SINCE 1949

SKU: 82-270-USA / 82-270A-USA

Medium Magnetic Tumblers

Product Manual

8/22/23 Romanoff.com • [email protected] • 631-842-2400 Page 1 of 4

 82-270-USA / 82-270A-USA Romanoff Medium Magnetic Tumbler

Thank You For Your Purchase!

Congratulations on the purchase of your new Romanoff Medium Magnetic Tumbler.

Please keep in mind that, due to the internal circuitry protection of the unit, rotation will
begin 45 seconds after green button is pressed. As a suggestion as to the use of the
unit, please use the following as a general guide:

1. Fill bowl with approximately 2 inches of water.

2. Fill the bowl with approximately one cup (8 ounces) of soap (BCR recommended)
3. Place ½ pound of stainless steel shots (one of the containers provided).
4. Place pieces to be tumbled inside bowl and run for 45 minutes at a speed of
approximately 6.5.

The timer on the unit controls total tumbling time. The unit will automatically reverse
rotation approximately every 7 minutes. If desired finish is not accomplished after the
first run, some experimentation should be done with regards to motor speed, amount of
water, shot and soap used. However, the amounts given above have been proven to be
generally successful. Good Luck!

8/22/23 Romanoff.com • [email protected] • 631-842-2400 Page 2 of 4

 82-270-USA / 82-270A-USA Romanoff Medium Magnetic Tumbler

1.SAFETY INSTRUCTIONS
GROUND INSTRUCTIONS 1. GROUND INSTRUCTIONS
This tool should be grounded while in use to This tool should be grounded while in use to
protect the operator from electric shock. The tool is protect the operator from electric shock. The tool is
equipped with an approved three-conductor cord equipped with an approved three-conductor cord
Figure 1
and three-prong grounding type plug to fit the and three-prong grounding type plug to fit the
proper grounding type receptacle. The green (or proper grounding type receptacle. The green (or
green and yellow) conductor in the cord is the green and yellow) conductor in the cord is the
grounding wire. grounding wire.
Never connect the green (or green and yellow) Never connect the green (or green and yellow)
wire to a live terminal. If your unit is for use on lesswire to a live terminal. If your unit is for use on less
than 150 volts, it has a plug that looks like that than 150 volts, it has a plug that looks like that
A. Cover of grounded B.
shown in sketch outlet
(A) in box
Figure 1. If it is for use on shown in sketch (A) in Figure 1. If it is for use on
150 to 250 volts, it has a plug that looks like that 150 to 250 volts, it has a plug that looks like that
shown in sketch (B). Use of an extension cords orshown in sketch (B). Use of an extension cords or
a 2 prong adapter is not recommended. a 2 prong adapter is not recommended.

2. TOOL SAFETY INSTRUCTIONS

1. Keep Work Area Clean 1.8.Keep
Use Work
Safety AreaGlassesClean
Cluttered areas and benches invite Cluttered
Use safety areas and benches
glasses invite tools.
with all rotating
accidents. accidents.
Also use a face or dust mask if cutting
operation is dusty.
2. Avoid Dangerous Equipment 2. Avoid Dangerous Equipment
Don’t expose power tools to rain. Don’t use 9.Don’t
Don't expose
Abuse power
Cordtools to rain. Don’t use
power tools in damp or wet locations. Keep power
Never tools
carryin tool
damp byor wetorlocations.
cord yank it toKeep
work area well lit. work area wellfrom
disconnect lit. receptacle. Keep cord
from heat, oil, and sharp edges.
3. Keep Children Away 3. Keep Children Away
All visitors should be kept safe distance AllSecure
10. visitorsWork
should be kept safe distance
from work area and appliance. from
Usework areaorand
clamps appliance.
a vise to hold work. It's
safer than using your hand and it frees
4. Store Idle Tools 4. Store
bothIdle
handsToolsto operate tool.
When not in use, tools should be stored in When not in use, tools should be stored in
dry, high, and locked location out of the dry,
11. high,Overreach
Don't and locked location out of the
reach of children. reach
Keepofproper
children. footing and balance at all
times.
5. Don't Force Tool 5. Don't Force Tool
It will do the job better and be safe at the It will
12. do theTools
Maintain job betterwithand
Carebe safe at the
rate for which it was designed. rate
Keepfor which it wasand
tools sharp designed.
clean for best and
safest performance. Follow instructions
6. Use Right Tool 6. Use for Right Tool and changing accessories.
lubricating
Don’t force small tool or attachment to do Don’t force small tool or attachment to do
the job of a heavy-duty tool. the
13. job of a heavy-duty
Disconnect Tools tool.
When not in use; before servicing; when
7. Wear Proper Apparel 7. Wear Proper
changing Apparel such as blades,
accessories
Do not wear loose clothing or jewelry Dobits,
notcutters,
wear loose etc. clothing or jewelry
which may get caught in moving parts. which may get caught in moving parts.
Tie back long hair or use a proper hair net. TieAvoid
14. back Accidental
long hair or Starting
use a proper hair net.
Be sure switch is OFF when plugging in.

8/22/23 Romanoff.com • [email protected] • 631-842-2400 Page 3 of 4

 82-270-USA / 82-270A-USA Romanoff Medium Magnetic Tumbler

WARRANTY POLICY

Romanoff warrants all products furnished by it are free from defects in material and
workmanship at the time of shipment for a period of eighteen (18) months from the date
of shipment, or one (1) year from the date of installation, whichever occurs first. Claims
must be made during that period and are limited to the replacement of parts claimed to
be defective.

This warranty shall not extend to products that have been misused,
neglected, altered or repaired without factory authorization during the warranty
period. Operating conditions beyond our control such as improper voltage,
excessive ambient temperatures, or other conditions that would affect the
performance or life of the product will also cause the warranty to become void.

Permission to return parts for warranty repair must be obtained, and all
returns must be prepaid factory. If, after examination, the product or part is found
to be defective, it will be repaired or replaced on a no-charge basis and returned.
On the other hand, if it is determined that the warranty has not been breached by
Romanoff then the usual charges for repair or replacement will be
made. Parts or products that are obsolete or those made to special order are not
returnable.

This limited warranty applies only to the above and is for the period set
forth. Romanoff maximum liability shall not, in any case, exceed the contract price for
the product, part, or component claimed to be defective; and Romanoff assumes no
liability at all for any special, indirect, or consequential damages arising from defective
equipment.

THERE ARE NO WARRANTIES APPLIED OR EXPRESSED THAT

EXTEND BEYOND THOSE CONTAINED IN THIS LIMITED WARRANTY.

8/22/23 Romanoff.com • [email protected] • 631-842-2400 Page 4 of 4