Draft for Public Comment

Form 36

DPC: 23 / 30465607 DC

BSI Group Headquarters

Date: 24 January 2023
389 Chiswick High Road London W4 4AL Origin: European
Tel: +44 (0)20 8996 9000
Fax: +44 (0)20 8996 7400
www.bsigroup.com

Latest date for receipt of comments: 14 March 2023 Project No. 2022/02635

Responsible committee: ISE/110 Steel Tubes, and Iron and Steel Fittings

Interested committees:

Title: BS EN 10217-1:2019/A1 Welded steel tubes for pressure purposes - Technical delivery conditions

Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties

Please notify the secretary if you are aware of any keywords that might assist in classifying or identifying the standard or if the
content of this standard
i) has any issues related to 3rd party IPR, patent or copyright
ii) affects other national standard(s)
iii) requires additional national guidance or information

WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD.
THIS DRAFT IS NOT CURRENT BEYOND 14 March 2023

This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No
acknowledgement will normally be sent. See overleaf for information on the submission of comments.

No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs
and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to
dissemination by e-mail within such an organization by committee members.

Further copies of this draft may be purchased from BSI Shop http://shop.bsigroup.com
or from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email [email protected].
British, International and foreign standards are also available from BSI Customer Services.

Information on the co-operating organizations represented on the committees referenced above may be obtained from
http://standardsdevelopment.bsigroup.com

Responsible Committee Secretary: Ms Julie Weller (BSI)

Direct tel:
E-mail: [email protected]
Introduction
This draft standard is based on national and international discussions. Your comments on this draft are invited and will assist in
the preparation of the consequent standard.

For international standards, comments will be reviewed by the relevant UK national committee before sending the consensus
UK vote and comments to the international committee, which will then decide appropriate action. If the international standard is
approved, it is usual for the text to be published as a British Standard.

For national standards, comments will be reviewed by the relevant UK national committee and the resulting standards published
as a British Standard.

UK Vote
Please indicate whether you consider the UK should submit a negative (with supporting technical reasons) or positive vote on
this draft. Please indicate if you are aware of any reason why this draft standard should not be published as a British Standard.

Submission of Comments
- Annotated drafts are not acceptable and will be rejected.

- All comments should be submitted online at https://standardsdevelopment.bsigroup.com/. You will need to register in
order to comment.

Template for comments and secretariat observations Date: xx/xx/20xx Document: ISO/DIS xxxx

1 2 (3) 4 5 (6) 7
MB Clause No./ Subclause Paragraph/Figure/ Type of Commend (justification Proposed change by the MB Secretariat observations on
No./Annex (e.g. 3.1) Table/Note comment for change) by the MB each comment submitted

3.1 Definition 1 ed Definition is ambiguous and needs Amend to read '...so that the mains
clarifying. connector to which no connection...'

6.4 Paragraph 2 te The use of the UV photometer as Delete reference to UV photometer.

an alternative cannot be supported
as serious problems have been
encountered in its use in the UK.
EUROPEAN STANDARD DRAFT
NORME EUROPÉENNE EN 10217-1:2019
EUROPÄISCHE NORM prA1
January 2023

ICS 23.040.10; 77.140.75

English Version

Welded steel tubes for pressure purposes - Technical

delivery conditions - Part 1: Electric welded and
submerged arc welded non-alloy steel tubes with specified
room temperature properties
Tubes soudés en acier pour service sous pression - Geschweißte Stahlrohre für Druckbeanspruchungen -
Conditions techniques de livraison - Partie 1 : Tubes en Technische Lieferbedingungen - Teil 1: Elektrisch
acier non allié, soudés électriquement et soudés à l'arc geschweißte und unterpulvergeschweißte Rohre aus
immergé, avec caractéristiques spécifiées à unlegierten Stählen mit festgelegten Eigenschaften bei
température ambiante Raumtemperatur

This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC
459/SC 10.

This draft amendment A1, if approved, will modify the European Standard EN 10217-1:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10217-1:2019/prA1:2023 E
worldwide for CEN national Members.
EN 10217-1:2019/prA1:2023 (E)

Contents Page

European foreword ...................................................................................................................................................... 3

1 Modification to the European foreword ................................................................................................. 4
2 Modification to Clause 2 “Normative references” ............................................................................... 4
3 Modifications to 7.2.5, Table 1 ................................................................................................................... 5
4 Deletion of Annex B ........................................................................................................................................ 5

2
 EN 10217-1:2019/prA1:2023 (E)

European foreword
This document (EN 10217-1:2019/prA1:2023) has been prepared by Technical Committee
CEN/TC 459/SC 10 “Steel tubes, and iron and steel fittings”, the secretariat of which is held by UNI.

This document is currently submitted to the CEN Enquiry.

3
EN 10217-1:2019/prA1:2023 (E)

1 Modification to the European foreword

Add the following paragraph "In comparison with the previous version of this edition, EN 10217-1:2019,
the following technical modifications have been made in the amended and new version of edition
EN 10217-1:2019:
— in Table 1 for manufacturing route 1 for small diameter the possibility to use cold rolled strip was
added;

— references to EN ISO 10893 and EN ISO 6892-1 were updated;

— Annex B was deleted.".

2 Modification to Clause 2 “Normative references”

Update the following references including their footnotes to text:
EN ISO 6892-1:2019, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
(ISO 6892-1:2019)
EN ISO 10893-1:2011, 1 Non-destructive testing of steel tubes — Part 1: Automated electromagnetic testing
of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leak
tightness (ISO 10893-1:2011)
EN ISO 10893-2:2011, 2 Non-destructive testing of steel tubes — Part 2: Automated eddy current testing of
seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO
10893-2:2011)
EN ISO 10893-3:2011, 3 Non-destructive testing of steel tubes — Part 3: Automated full peripheral flux
leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the
detection of longitudinal and/or transverse imperfections (ISO 10893-3:2011)
EN ISO 10893-6:2019, Non-destructive testing of steel tubes — Part 6: Radiographic testing of the weld
seam of welded steel tubes for the detection of imperfections (ISO 10893-6:2019)
EN ISO 10893-7:2019, Non-destructive testing of steel tubes — Part 7: Digital radiographic testing of the
weld seam of welded steel tubes for the detection of imperfections (ISO 10893-7:2019)
EN ISO 10893-10:2011, 4 Non-destructive testing of steel tubes — Part 10: Automated full peripheral
ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of
longitudinal and/or transverse imperfections (ISO 10893-10:2011)
EN ISO 10893-11:2011, 5 Non-destructive testing of steel tubes — Part 11: Automated ultrasonic testing of
the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO
10893-11:2011)

1 As impacted by EN ISO 10893-1:2011/A1:2020.

2 As impacted by EN ISO 10893-2:2011/A1:2020.
3 As impacted by EN ISO 10893-3:2011/A1:2019 and EN ISO 10893-3:2011/A2:2020.
4 As impacted by EN ISO 10893-10:2011/A1:2020.
5 As impacted by EN ISO 10893-11:2011/A1:2020.

4
 EN 10217-1:2019/prA1:2023 (E)

3 Modifications to 7.2.5, Table 1

Insert in Table 1 for manufacturing route 1a to 1d in the fourth column "or for small wall thicknesses up to
2 mm cold rolled strip is also permitted”.

4 Deletion of Annex B
Delete Annex B in its entirety.