Installation guide of Pandora security-service and remote start system for

Toyota Yaris IV 2020 - ...

Push-to-Start button
Automatic transmission
Model code: 2149

WARNING! This installation manual has the status of recommendation.

This system MUST BE installed by a certified technician.

Connect the wires only when the base unit is disconnected.

It’s prohibited to place the wires near sharp elements and moving parts of a car. Wiring through the
holes should be passed using special rubber bushings.
The car’s electrical scheme and wire colors may differs from the information shown in this guide,
so suggested connection points MUST BE checked before installation.

www.pandorainfo.com e-mail: [email protected]

Page 1
Document structure:
• Commands and statuses / components location
• System settings
• Wiring diagram
• Learning procedure

It’s necessary to install special software before starting the installation of the security
system to the car. Base unit settings can be configured by:

1. «Alarm Studio» program:

• Download the latest version of Alarm Studio: https://pandorainfo.com/alarmstudio-firmware/

(program is archived, ZIP file is password protected);
• Unpack the archive > run the program > connect the base unit to PC;
• Switch the base unit to program mode by entering «service PIN-code» using Valet button (1-1-1-
1 by default);
• Update the firmware of the base unit, choose the vehicle model and adjust the settings of
security system in accordance with the «System settings» table.
•
2. Using «Pandora Specialist» application:

• Download the app from Play Market/App Store, create an account, log in;
• Connect the base unit to mobile device via Bluetooth or using USB-OTG cable, following the tips
in the application;
• Update the firmware of the base unit and Bluetooth modem;
• Download the configuration for selected vehicle, if it available, from «Quick installation» section
or change the settings of security system using «Advanced mounting» menu.

Loading
ready-made
configurations
If Bluetooth connection is choosed:
1. Enter «service PIN-code»;
2. Go to 50th programming level
according to user’s guide and pair the
system followings the tips in the app.
Manual configuring
of the system

www.pandorainfo.com e-mail: [email protected] Toyota Yaris IV 2020 - ...

Page 2
 Bus
Bus

code
2149

CAN 1
CAN 1

IMO/IMI
Model

-
•
•
Algorithmic immobilizer bypass Driver door

-
•
Takeover 4 Passenger door

•
•
Remote start from car’s key Rear left door

-
•
ACC\Autolights OFF via CAN Rear right door

RS features

-
-
Remote start via CAN Hood

www.pandorainfo.com
-
•

connector
Distance to empty Trunk

Wire-to-Wire
-
•
Washer fluid level Ignition

-
•
Window glass position Brake pedal

-
•
Tires pressure (TPMS) Parking lights

Advanced
parameters *

-
•
OBD II diagnostic trouble codes Parking brake

-
•

Battery charger connector status Neutral status

-
•

Fast charging Tachometer

-
•

BCM module
Slow charging Slave mode

-
•

Remaining distance on HV battery Slave by trunk

Statuses

-
-

«Ready» status Slave by OE remote start

-
-

Battery state of health (SOH) OE alarm status

in hybrid vehicles

-
-

Battery state of charge (SOC) Vehicle speed

-
L

Advanced parameters for

HV battery temperature Fuel level 1

e-mail: [email protected]
-

Engine temperature
-

Outside temperature
-

Interior temperature

COMPONENTS LOCATION
COMMANDS AND STATUSES

Central lock status

3 - Hazard lights;
-

Mileage
-

Valet button
•

- Smart Pro V3, Smart V3

Validator buttons 2
-

settings of the alarm system.

Central lock control

•

1 - Fuel level is displayed in liters;

Windows closing at arming

Smart key ECU

H

Parking lights control 3

All connections are located at Smart key ECU, in a Wire-to-Wire connector and at BCM module.
-

Arm OE alarm
2 - Shift lever knob, only with ignition OFF;
-

Disarm OE alarm
-

Trunk release
-
Commands

Additional function via CAN

electric, hybrid and plug- * Security systems that support advanced parameters:
-

Pre-heater control
4 - Choose «Stop engine when disarming» parameter in the
-

Blocking via CAN

BACK
•

Keyless entry blocking

Page 3
Toyota Yaris IV 2020 - ...
 SECURITY SYSTEM SETTINGS

Name Item Setting Note

Setting of the warning level of the shock sensor 1.1.1 30
Setting of the alarm level of the shock sensor 1.1.2 25 Test the sensitivity after
Setting of the alarm level of the motion sensor 1.1.3 25 installation. Adjust if necessary
I. MAIN

Setting of the alarm level of the tilt sensor 1.1.4 25

Algorithm of processing data from accelerometer 1.1.12 Algorithm F
Radio tag RSSI level 1.8(9).5 120% (max)
Radio tag hysteresis 1.8(9).6 5%
II. AUTOMATIC START

Transmission type 2.1.2 Automatic

Stop engine when disarming 2.1.14 Enable

Car with START/STOP button 2.2.1 Disable
Enable bypass when engine is running 2.3.1 Enable
Keyless bypass option 2.3.3 Toyota imo_imi v3
III. NPUTS / OUTPUTS

Assign the inputs according to the wiring diagram. All other

Inputs settings 3.1
inputs should be DISABLED.

Assign the outputs according to wiring diagram and selected

Outputs settings 3.2
channels. All other outputs should be DISABLED.

Valet button 5.2.9 Disable

Central lock control 5.3.1 Disable
Turn lights control 5.3.3 Enable
V. CAN

Control over vehicle security system 5.3.5 Disable

Slave mode when arming factory alarm 5.4.1 Enable
Slave mode when disarming factory alarm 5.4.2 Enable
Slave mode when the trunk is opening 5.4.3 Enable
VII. GPS

GPS anchor 7.1.3 Disable

BACK

www.pandorainfo.com e-mail: [email protected] Toyota Yaris IV 2020 - ...

Page 4
 WIRING DIAGRAM BACK

Pin#6: green
IMO
2 White IMI connector side
1 Green IMI vehicle side Pin#5: red
IMI
LED
3 Black IMO
External
Wire and wire connector «AH5».
button
White, to the left of driver’s power
distribution box
Valet
Base unit

Engine/Starter
blocking circuit

Temperature Blue/Black CHx Blocking N.C.

sensor
Blue/Red CHx Blocking N.C.

10А
To +12V
Red +12V

Orange CHx Starter (+)

Pin#3: pink
Orange CHx+ Starter (+) Starter (+)

It's allowed to directly supply a starter output without using

an additional relay/relay module for systems with ajustable
polarity(-/+) of output channels or with positive outputs
«H45» Smart Key ECU
connector, behind the
glove box
Status
LED

CHx- Status LED (-)

Use an additional resistor if

560 Ω Pin#22: blue
it’s not built inside status LED
+12V
3А
Red +12V Pin#2: white
Beeper CAN 1 L
CHx- Beeper (-)
Pin#1: blue
CAN 1 H
Orange/White CAN1 H

Orange/Black CAN1 L

«H46» Smart Key ECU

connector, behind the
glove box

Black GND

Pin#29: white/
black - «GND»
Pin#4: purple
Unlock (-)
Pin#28: green
Lock (-)
«H4» BCM module
connector, at left power
distribution box

CHx- Unlock (-)

CHx- Lock (-)

Brown/White INPx- Hood (-) Bonnet switch

Purple CHx+ Siren (+) Siren

www.pandorainfo.com e-mail: [email protected] Toyota Yaris IV 2020 - ...

Page 5
 LEARNING AT THE VEHICLE BACK

1. Switching to the program mode*.

Conditions:
- System is disarmed;
- System is not in the service mode; Press

1.1 - Ignition is OFF.

shortly
1 time
X4
With ~ 2
Enter «Service PIN-code» (1-1-1-1 by default) short one-time (for code sec. pause

1-1-1-1) pressings of the «Valet» button with ~ 2 sec. pauses.

Successful entering of «Service PIN-code» will be confirmed by a

series of red and green flashes of LED indicator.
1.2
If PIN-code was entered incorrectly, LED will light red for a while.
Repeat entering ot the PIN-code after 5 sec.

2. Learning of immobiliser bypass.

Enter 17th programming level: Press

2.1 - Press «Valet» button 17 times in a row with intervals of no more than
shortly
1 time
X 17
1 sec.

Successful entering to 17th level will be confirmed by 17 red flashes of X 17 +

2.2
LED indicator and 17 short sound signals of siren/beeper.
X 17

LED will light solid green. Start the engine (turn READY ON). OFF ACC IGN START

2.3 If the procedure fails (LED blinks red, siren sounds several times),
ENGINE
START
STOP

check the settings and/or connection of the security system and repeat
the learning attempt.

2.4 Wait, LED will blink green then turn solid green. Siren will sound once.

+ X1

OFF ACC IGN START

Press
shortly ENGINE

2.5 Press «Valet» button and turn the ignition OFF. 1 time
START
STOP

OFF ACC ON START

IGN OFF ACC IGN START

ENGINE ENGINE
START START
STOP STOP

Turn the ignition ON and OFF again. System will be rebooted after 5
2.6
sec. and will be ready for CLONE procedure.

Perform the CLONE procedure using Alarm Studio program or Pandora

2.7
Specialist application. Learning is finished.

*All described steps can be perfomed manually or in automated mode using «Pandora Specialist» application

www.pandorainfo.com e-mail: [email protected] Toyota Yaris IV 2020 - ...

Page 6