Product Information for LOGO!

System Manual in 06/2023 edition

Introduction 1

Certification and approvals 2

Secure decommissioning 3

Technical data 4
LOGO!
Product Information for LOGO! LOGO! power modules
5
order number
System Manual in 06/2023 edition

Product Information

05/2024
A5E53808149-AA
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens Aktiengesellschaft. The remaining trademarks in
this publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens Aktiengesellschaft A5E53808149-AA Copyright © Siemens 2024.

Digital Industries Ⓟ 05/2024 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Table of contents

1 Introduction ........................................................................................................................................... 4
2 Certification and approvals ................................................................................................................... 5
3 Secure decommissioning....................................................................................................................... 9
3.1 Securely removing data........................................................................................................ 9
3.2 Recycling and disposal ....................................................................................................... 10
4 Technical data...................................................................................................................................... 11
4.1 General technical data ....................................................................................................... 11
4.2 Technical data: LOGO! 230................................................................................................. 14
4.3 Technical data: LOGO! DM8 230R and LOGO! DM16 230R .................................................. 16
4.4 Technical data: LOGO! 24................................................................................................... 18
4.5 Technical data: LOGO! DM8 24 and LOGO! DM16 24 .......................................................... 20
4.6 Technical data: LOGO! 24RC............................................................................................... 22
4.7 Technical data: LOGO! DM8 24R and LOGO! DM16 24R ...................................................... 24
4.8 Technical data: LOGO! 12/24... LOGO! DM8 12/24R ............................................................ 26
4.9 Technical data: LOGO! TDE (Text Display with Ethernet interfaces)...................................... 28
5 LOGO! power modules order number ................................................................................................. 30
Index .................................................................................................................................................... 31

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 3
Introduction 1
This product information describes revision and supplements to the LOGO! System Manual
(A5E33039675-AL) in edition 06/2023:
• Revision of certification and approvals
• Supplement of LOGO! devices secure decommissioning
• Revision of LOGO! BM technical data
• Revision of LOGO! power modules order number
You can find LOGO! System Manual (A5E33039675-AL) in edition 06/2023 on Siemens
Industry Online Support (https://support.industry.siemens.com/cs/us/en/view/109826499).
This product information applies to the following LOGO! devices:

Variant Designation Order number

LOGO! Basic (Base Module LOGO! 12/24RCE * 6ED1052-1MD08-0BA2
with display) LOGO! 24CE * 6ED1052-1CC08-0BA2
LOGO! 24RCE (AC/DC) 6ED1052-1HB08-0BA2
LOGO! 230RCE (AC/DC) 6ED1052-1FB08-0BA2
LOGO! Pure (Base Module LOGO! 12/24RCEo * 6ED1052-2MD08-0BA2
without display) LOGO! 24CEo * 6ED1052-2CC08-0BA2
LOGO! 24RCEo (AC/DC) 6ED1052-2HB08-0BA2
LOGO! 230RCEo (AC/DC) 6ED1052-2FB08-0BA2
Digital modules LOGO! DM8 12/24R 6ED1055-1MB00-0BA2
LOGO! DM8 24 6ED1055-1CB00-0BA2
LOGO! DM8 24R 6ED1055-1HB00-0BA2
LOGO! DM8 230R 6ED1055-1FB00-0BA2
LOGO! DM16 24 6ED1055-1CB10-0BA2
LOGO! DM16 24R 6ED1055-1NB10-0BA2
LOGO! DM16 230R 6ED1055-1FB10-0BA2
Analog modules LOGO! AM2 6ED1055-1MA00-0BA2
LOGO! AM2 RTD 6ED1055-1MD00-0BA2
LOGO! AM2 AQ (0...10V, 0/4...20mA) 6ED1055-1MM00-0BA2
Text Display module with LOGO! TDE 6ED1055-4MH08-0BA1
Ethernet interfaces

*: Also with analog inputs

Product Information for LOGO! System Manual in 06/2023 edition

4 Product Information, 05/2024, A5E53808149-AA
Certification and approvals 2
Certification and approvals
LOGO! is certified to cULus and cFMus.
• cULus Haz. and ordinary Loc.
Underwriters Laboratories Inc. (UL) to
- UL 508 (Industrial Control Equipment)
- CSA C22.2 No. 142 (Process Control Equipment)
- UL 121201 (Hazardous Location)
- CSA C22.2 No.213 (Hazardous Location)
APPROVED for use in
Class I, Division 2, Group A, B, C, D T4
Class I, Zone 2, Group IIC Tx
• FM Approval (US Approval and Canada Approval)
Factory Mutual Research (FM) to
- Approval Standard Class Number 3611, 3600, 3810
- ANSI/UL 61010-1
- ANSI/UL 121201
- ANSI/IEC60529
- ANSI/NEMA 250
- CSN/CSA-C22.2 No. 213
- CAN/CSA-C22.2 No. 61010-1
- CAN/CSA-C22.2 No.94
APPROVED for use in
- Class I, Division 2, Group A, B, C, D Tx
- Class I, Zone 2, Group IIC Tx

WARNING
Substitution of components can impair the suitability for Class I, Division 2 and
Zone 2.
Repair of units must be done by an authorized Siemens Service Center.

Note
You will find current approvals on the rating plate of the relevant module.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 5
Certification and approvals

LOGO! is issued with the CE Certificate of Conformity. It is compliant with following

standards:
• EN 61131-2
• EN 61000-6-1, EN 61000-6-2, EN 61000-6-3, EN 61000-6-4
• EN IEC 63000
Marine certificate of approval:
• ABS (American Bureau of Shipping)
• BV (Bureau Veritas)
• DNV-GL (Det Norske Veritas (Norwegen)-Germanischer Lloyd)
• LRS (Lloyds Register of Shipping)
• Class NK (Nippon Kaiji Kyokai)
• CCS (CHINA CLASSIFICATION SOCIETY)
• KR (KOREAN REGISTER)

ID for Australia

Our products carrying the label shown at the side are compliant with AS/NZS
61000.6.4, AS/NZS 61000.6.3 standard.

ID for Korea

Our products (except the LOGO! CSM modules) carrying the label shown at the
side are compliant with Korean standards.

WEEE label (European Union)

Disposal instructions, observe the local regulations and below Recycling and
Disposal.

Product Information for LOGO! System Manual in 06/2023 edition

6 Product Information, 05/2024, A5E53808149-AA
 Certification and approvals

Recycling and disposal

You can fully recycle LOGO! devices due to their low-pollutant equipment. For
environmentally friendly recycling and disposal of your old equipment, contact a certified
electronic waste disposal company and dispose of the equipment according to the applicable
regulations in your country.

UK Conformity Assessed marking

The device complies with the designated British standards (BS) for programmable logic
controllers published in the official consolidated list of the British Government. The device
meets the requirements and protection targets of the following regulations and related
amendments:
• Electrical Equipment (Safety) Regulations 2016 (Low-Voltage)
• Electromagnetic Compatibility Regulations 2016 (EMC)
• Regulations on the restriction of the use of certain hazardous substances in electrical and
electronic equipment 2012 (RoHS).
UK Declarations of Conformity for the respective authorities are available from:
Siemens AG
Digital Industries
Factory Automation
DI FA TI COS TT
P.O. Box 1963
D-92209 Amberg
The UK Declaration of Conformity is also available for download from the Siemens Industry
Online Support website under the keyword "Declaration of Conformity".
Approval Standard Class Number 3611, 3600, 3810Factory Mutual Research (FM) in
accordance with
Approval Standard Class Number 3611, 3600, 3810
ANSI/UL61010-1, ANSI/UL 121201
CAN/CSA-C22.2 No. 0-10
CSA C22.2 No. 213
CAN/CSA-C22.2 No. 61010-1
APPROVED for use in Class I, Division 2, Group A, B, C, D T4;
Class I, Zone 2, Group IIC Tx
Installation Instructions for FM
• WARNING – Explosion Hazard – Do not disconnect while circuit is live unless area is
known to be non-hazardous.
• WARNING - Explosion Hazard - Substitution of components may impair suitability for Class
I, Division 2 or Zone 2.
• This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class I, Zone 2,
Group IIC; or non-hazardous locations.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 7
Certification and approvals

LOGO! modules are therefore suitable for use in industrial and residential areas. Use in Class I,
Division 2, Group A, B, C and D locations or in non-hazardous locations is supported.

Identification for Eurasion Customs Union

• EAC (Eurasian Conformity)
• Customs union of Russia, Belarus and Kazakhstan
• Declaration of conformity according to Technical Regulations of the Customs Union (TR
CU)

CCCEx approval
The following approvals according to the following standards are valid for a device with the
"CCC" marking.
• Standards:
– GB/T 3836.1-2021 (Explosive atmospheres - Part 1: Equipment - General requirements)
– GB/T 3836.3-2021 (Explosive atmospheres - Part 3: Equipment protection by increased
safety "e")
– GB/T 3836.8-2021 (Explosive atmospheres - Part 8: Equipment protection by type of
protection "n")
• Approvals:
– Ex ec nC IIC T4 Gc (module with relay outputs)
– Ex ec IIC T4 Gc
– -20 °C to +55 °C

Special conditions for safe operation of the devices

• The equipment shall only be used in an area of not more than pollution degree 2, as
defined in GB/T 16935.1.
• The equipment shall be installed in an enclosure that provides a minimum ingress
protection of IP 54 in accordance with GB/T 3836.1, and accessible only by use of a tool.
• Transient protection shall be provided that is set at a level not exceeding 140% of the peak
rated voltage value at the supply terminals to the equipment.
• Antenna shall be installed within the end use enclosure. Routing and remote installation
(not evaluated as part of this certification) of the antenna shall be in accordance with the
appropriate location regulations when installed in unclassified and/or zone 2 Hazardous
Locations.

Product Information for LOGO! System Manual in 06/2023 edition

8 Product Information, 05/2024, A5E53808149-AA
Secure decommissioning 3
In this section, you will find information on how to properly decommission individual
components of your automation system. Decommissioning is necessary when the component
has reached the end of its service life.
Decommissioning includes environmentally sound disposal and secure removal of all digital
data of electronic components with storage medium.

3.1 Securely removing data

Before disposing of components of your automation system, you should securely delete all
data from the storage media of these components. How to securely delete data from the
devices so that it cannot be recovered is described below.

NOTICE
Data misuse resulting from non-secure deletion of data
Incomplete or non-secure deletion of data from data memories can result in data misuse by
third parties.
For this reason, ensure secure deletion of data from all storage media used before disposing
of the product.

To delete all data from the data memories of LOGO! device, reset the device to factory
setting. The function deletes all information that was saved internally on the module. You
can take the following three methods to reset your LOGO! device to factory setting.

Factory reset by LOGO! BM/TDE menu command

1. Switch the LOGO! to programming mode. LOGO! opens the main menu:
2. Press or to move the cursor to ①, then press OK. LOGO! open the programming menu.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 9
Secure decommissioning
3.2 Recycling and disposal

3. Move the cursor to ②, then press OK.

4. Move the cursor to ③, then press OK to confirm factory reset operation.

Factory reset by LOGO!Soft Comfort

Use menu command in LOGO!Soft Comfort: Tools -> Transfer -> Factory Reset LOGO!. For
detailed operation, refer to the section: Tools -> Transfer -> Factory Reset LOGO! (LOGO!
8.FS4 and later versions only) in LOGO!Soft Comfort Online Help.

Factory reset by reset file

1. Copy _reset.bm file in the DVD-ROM into the root directory of an SD card.
2. Insert the SD card into the LOGO! BM.
3. Power on the LOGO! BM to execute factory reset. After the BM is reset to factory setting,
_reset.bm file in the SD card is deleted automatically.

Note
The _reset.bm file can only be used to reset factory setting for LOGO! BM 8.3 and later
versions.

3.2 Recycling and disposal

You can fully recycle LOGO! devices due to their low-pollutant equipment. For
environmentally friendly recycling and disposal of your old equipment, contact a certified
electronic waste disposal company and dispose of the equipment according to the applicable
regulations in your country.

Product Information for LOGO! System Manual in 06/2023 edition

10 Product Information, 05/2024, A5E53808149-AA
Technical data 4
4.1 General technical data

Criterion Tested in Values

accordance with
LOGO! Base Modules (0BA8)
LOGO! Basic
Dimensions (WxHxD) 71.5 x 90 x 60 mm
Weight
• Modules with relay output Approx. 240 g
• Modules with transistor output Approx. 195 g
Installation On a 35 mm profile rail four module
widths or wall mounting

LOGO! Pure
71.5 x 90 x 58 mm
Dimensions (WxHxD)
Weight
Approx. 200 g
• Modules with relay output
Approx. 160 g
• Modules with transistor output On a 35 mm profile rail four module
Installation widths or wall mounting
LOGO! expansion modules DM16...
Dimensions (WxHxD) 71.5 x 90 x 58 mm
Weight
• Modules with relay output Approx. 225 g
Approx. 165 g
• Modules with transistor output
On a 35 mm profile rail four module
Installation widths or wall mounting
LOGO! expansion modules
DM8...
Dimensions (WxHxD) 35.5 x 90 x 58 mm
Weight
• Modules with relay output Approx. 130 g
• Modules with transistor output Approx. 95 g
On a 35 mm profile rail two module
Installation widths or wall mounting
LOGO! expansion modules
AM...
Dimensions (WxHxD) 35.5 x 90 x 58 mm
Weight Approx. 95 g
Installation On a 35 mm profile rail two module
widths or wall mounting
LOGO! TDE (Text Display with
Ethernet interfaces)
Dimensions (WxHxD) 128.2 x 86 x 38.7 mm
Weight Approx. 220 g
Installation Bracket mounting

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 11
Technical data
4.1 General technical data

Criterion Tested in Values

accordance with
Climatic conditions
Ambient temperature for BM and EM Low temperature to
IEC 60068-2-1
• Horizontal installation • -20 °C to +55 °C 1)
High temperature to
• Vertical installation IEC 60068-2-2 • -20 °C to +55 °C
Ambient temperature for TDE Low temperature to
IEC 60068-2-1
• Horizontal installation • -20 °C to +55 °C 1)
High temperature to
• Vertical installation IEC 60068-2-2 • -20 °C to +55 °C
Storage and Transport - 40 °C to +70 °C
Relative humidity IEC 60068-2-30 From 10% to 95% no condensation
Atmospheric pressure, Altitude
• Operation • 1080 to 795 hPa, corresponds to
• Storage/transport an elevation of -1000 m to 2000 m
• 1080 to 660 hPa, corresponds to
an elevation of -1000 m to 3500 m
Altitude during operation Up to 2000 m
Pollutants IEC 60068-2-42 SO2 10 cm3/m3, 21 days
IEC 60068-2-43 H2S 1 cm3/m3, 21 days
Pollution degree 2
Ambient mechanical conditions
Degree of protection • IP20 for LOGO! Base Modules,
expansion modules, and the
LOGO! TDE excluding the TDE
front panel
• IP65 for LOGO! TDE front panel
Enclosure type • Type 1 for the front panel of
LOGO! Base Modules and
expansion modules
• Type 4X/12 for LOGO! TDE front
panel
Vibrations: IEC 60068-2-6 5 Hz to 8.4 Hz
(constant amplitude 3.5 mm)
8.4 Hz to 200 Hz
(constant acceleration 1 g)
Shock IEC 60068-2-27 half-sine wave 15 g/11 ms
Free fall (packaged) IEC 60068-2-32 0.3 m
Electromagnetic compatibility (EMC)
Radiated emission EN 61000-6-3 Limit class B group 1
EN 61000-6-4 Limit class B
Electrostatic discharge IEC 61000-4-2 ±2 kV, ±4kV, ±8 kV air discharge
±6 kV contact discharge
Radiated electromagnetic field IEC 61000-4-3 80 MHz-1000 MHz and 1.4 GHz-
2.0 GHz 10V/m, 80% AM(1 kHz)
2.0 GHz-6.0 GHz 3V/m, 80%
AM(1 kHz)

Product Information for LOGO! System Manual in 06/2023 edition

12 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.1 General technical data

Criterion Tested in Values

accordance with
Conducted disturbance IEC 61000-4-6 150 KHz-80 MHz
10 V, 80%AM(1 kHz)
Fast transient bursts IEC 61000-4-4 • For power port: 2 kV
• For signal port:
– Signal Lines<30 m: 1 kV/5 kHz
and 100 kHz
– Signal Lines>30 m: 2 kV/5 kHz
and 100 kHz
Surge immunity (applies only to IEC 61000-4-5 1 kV line-to-line
LOGO! 230 and DM8/16 230R) 2 kV line-to-earth
Surge immunity (applies to low- With surge arrester (such as BVT AD
voltage (12 V or 24 V) LOGO! 24):
modules)
• 1 kV line-to-line
• 2 kV line-to-earth
Without surge arrester:
• 0.5 kV line-to-line
• 1 kV line-to-earth
Safety to IEC
Clearance and creepage distance IEC 60664, IEC Fulfilled
rating 61131-2, cULus to UL
508, CSA C22.2 No.
142, IEC 60730
Insulation strength IEC 61131-2 Fulfilled
Cycle time
Cycle time per function < 0.1 ms
Startup
Startup time at power-up Typ. 1.6 s
Overvoltage
Overvoltage category • Category II: LOGO! 24CE, LOGO!
DM8 24, LOGO! DM16 24, LOGO!
AM2, LOGO! AM2 RTD, LOGO!
AM2 AQ, LOGO! TDE
• Category III: LOGO! 12/24RCE,
LOGO! 24RCE (AC/DC), LOGO!
230RCE (AC/DC), LOGO! DM8
12/24R, LOGO! DM8 24R, LOGO!
DM8 230R, LOGO! DM16 24R,
LOGO! DM16 230R

1) The updating rate of LCD can be reduced at operating temperature less than 0°C.

Note
The maximum length for directly connecting two LOGO! Base Modules through CAT5e
shielded network cable is 100 meters.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 13
Technical data
4.2 Technical data: LOGO! 230...

4.2 Technical data: LOGO! 230...

LOGO! 230RCEo LOGO! 230RCE

Power supply
Input voltage 115 VAC/VDC to 240 VAC/VDC 115 VAC/VDC to 240 VAC/VDC
Permissible range 85 VAC to 265 VAC 85 VAC to 265 VAC
100 VDC to 253 VDC 100 VDC to 253 VDC
Input frequency 50/60 Hz 50/60 Hz
Permissible mains frequency 47 Hz to 63 Hz 47 Hz to 63 Hz
Power consumption
• 115 VAC • 20 mA to 40 mA • 20 mA to 40 mA
• 240 VAC • 15 mA to 25 mA • 15 mA to 25 mA
• 115 VDC • 10 mA to 20 mA • 10 mA to 20 mA
• 240 VDC • 5 mA to 15 mA • 5 mA to 15 mA
Voltage failure buffering
• 115 VAC/VDC • Typ. 10 ms • Typ. 10 ms
• 240 VAC/VDC • Typ. 20 ms • Typ. 20 ms
Power loss at
• 115 VAC • 2.3 W to 4.6 W • 2.3 W to 4.6 W
• 240 VAC • 3.6 W to 6.0 W • 3.6 W to 6.0 W
• 115 VDC • 1.2 W to 2.3 W • 1.2 W to 2.3 W
• 240 VDC • 1.2 W to 3.6 W • 1.2 W to 3.6 W
Backup of the real-time clock at 25 Typ. 20 days Typ. 20 days
°C
Accuracy of the real-time clock Typ. ± 2 s/day Typ. ± 2 s/day
Digital inputs
Number 8 8
Electrical isolation No No
Number of high speed inputs 0 0
Input frequency
• Normal input • Max. 4 Hz • Max. 4 Hz
• High speed input • -- • --
Digital input 115 to 240 VAC/DC, 50/60 Hz 115 to 240 VAC/DC, 50/60 Hz
Max. continuous permissible 265 VAC 265 VAC
voltage 253 VDC 253 VDC
Input voltage L1
• Signal 0 • < 40 VAC • < 40 VAC
• Signal 1 • > 79 VAC • > 79 VAC
• Signal 0 • < 30 VDC • < 30 VDC
• Signal 1 • > 79 VDC • > 79 VDC

Product Information for LOGO! System Manual in 06/2023 edition

14 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.2 Technical data: LOGO! 230...

LOGO! 230RCEo LOGO! 230RCE

Input current at
• Signal 0 • < 0.05 mA AC • < 0.05 mA AC
• Signal 1 • > 0.08 mA AC • > 0.08 mA AC
• Signal 0 • < 0.06 mA DC • < 0.06 mA DC
• Signal 1 • > 0.13 mA DC • > 0.13 mA DC
Delay time at 0 to 1:
• 120 VAC • Typ. 40 ms • Typ. 40 ms
• 240 VAC • Typ. 30 ms • Typ. 30 ms
• 120 VDC • Typ. 25 ms • Typ. 25 ms
• 240 VDC • Typ. 20 ms • Typ. 20 ms

Delay time at 1 to 0:
• 120 VAC • Typ. 45 ms • Typ. 45 ms
• 240 VAC • Typ. 70 ms • Typ. 70 ms
• 120 VDC • Typ. 60 ms • Typ. 60 ms
• 240 VDC • Typ. 75 ms • Typ. 75 ms
Line length (unshielded) max. 100 m max. 100 m
Digital outputs
Number 4 4
Output type Relay outputs Relay outputs
Electrical isolation Yes Yes
In groups of 1 1
Control of a digital input Yes Yes
Continuous current Ith Recommended range of Recommended range of
application ≥ 100 mA at application ≥ 100 mA at
12 VAC/VDC 12 VAC/VDC
Max. 10 A per relay Max. 10 A per relay
Relay rated voltage 240 VAC/VDC 240 VAC/VDC
Surge current Max. 30 A Max. 30 A
Incandescent lamp load (25000
switching cycles) at
• 230/240 VAC • 1000 W • 1000 W
• 115/120 VAC • 500 W • 500 W
Fluorescent tubes with ballast 10 x 58 W (at 230/240 VAC) 10 x 58 W (at 230/240 VAC)
(25000 switching cycles)
Fluorescent tubes, conventionally 1 x 58 W (at 230/240 VAC) 1 x 58 W (at 230/240 VAC)
compensated (25000 switching
cycles)
Fluorescent tubes, uncompensated 10 x 58 W (at 230/240 VAC) 10 x 58 W (at 230/240 VAC)
(25000 switching cycles)
Short circuit-proof cos 1 Power protection B16, 600 A Power protection B16, 600 A
Short circuit-proof cos 0.5 to 0.7 Power protection B16, 900 A Power protection B16, 900 A
Derating None; across the entire None; across the entire
temperature range temperature range
Parallel output circuits for power Not permitted Not permitted
increase

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 15
Technical data
4.3 Technical data: LOGO! DM8 230R and LOGO! DM16 230R

LOGO! 230RCEo LOGO! 230RCE

Protection of output relay (if Max. 16 A, characteristic B16 Max. 16 A, characteristic B16
desired)
Line length (unshielded) Max. 100 m Max. 100 m
Switching rate
Mechanical 10 Hz 10 Hz
Ohmic load/lamp load 2 Hz 2 Hz
Inductive load 0.5 Hz 0.5 Hz

Notice: For fluorescent lamps with capacitors, you must consider the technical data of
fluorescent lamp ballasts. If the current exceeds the maximum allowed surge current,
appropriate contactor relays must switch the fluorescent lamps.
Notice: Output: B300, R300; 8A, 24 VDC, G.P.; 10A, 240 VAC, G.P.; 3A, 120 VAC, Tungsten.
The data was determined with the following devices:
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 uncompensated.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 parallel compensated with 7 μF.
• Siemens fluorescent tubes 58 W VVG 5LZ 501 1-1N with ballast.

4.3 Technical data: LOGO! DM8 230R and LOGO! DM16 230R

LOGO! DM8 230R LOGO! DM16 230R

Power supply
Input voltage 115 VAC/VDC to 240 VAC/VDC 115 VAC/VDC to 240 VAC/VDC
Permissible range 85 VAC to 265 VAC 85 VAC to 265 VAC
100 VDC to 253 VDC 100 VDC to 253 VDC
Input frequency 50/60 Hz 50/60 Hz
Permissible mains frequency 47Hz to 63 Hz 47Hz to 63 Hz
Power consumption
• 115 VAC • 20 mA to 40 mA • 20 mA to 40 mA
• 240 VAC • 15 mA to 30 mA • 15 mA to 30 mA
• 115 VDC • 10 mA to 25 mA • 10 mA to 25 mA
• 240 VDC • 5 mA to 15 mA • 5 mA to 15 mA

Voltage failure buffering

• 115 VAC/VDC • Typ. 10 ms • Typ. 10 ms
• 240 VAC/VDC • Typ. 20 ms • Typ. 20 ms
Power loss at
• 115 VAC • 2.3 W to 4.6 W • 2.3 W to 4.6 W
• 240 VAC • 3.6 W to 7.2 W • 3.6 W to 7.2 W
• 115 VDC • 1.2 W to 2.9 W • 1.2 W to 2.9 W
• 240 VDC • 1.2 W to 3.6 W • 1.2 W to 3.6 W

Product Information for LOGO! System Manual in 06/2023 edition

16 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.3 Technical data: LOGO! DM8 230R and LOGO! DM16 230R

LOGO! DM8 230R LOGO! DM16 230R

Digital inputs
Number 4 8
Electrical isolation No No
Number of high speed inputs 0 0
Input frequency
• Normal input • Max. 4 Hz • Max. 4 Hz
• High speed input • -- • --
Digital input 115 to 240 VAC/DC, 50/60 Hz 115 to 240 VAC/DC, 50/60 Hz
Max. continuous permissible 265 VAC 265 VAC
voltage 253 VDC 253 VDC
Input voltage L1
• Signal 0 • < 40 VAC • < 40 VAC
• Signal 1 • > 79 VAC • > 79 VAC
• Signal 0 • < 30 VDC • < 30 VDC
• Signal 1 • > 79 VDC • > 79 VDC
Input current at
• Signal 0 • < 0.05 mA AC • < 0.05 mA AC
• Signal 1 • > 0.08 mA AC • > 0.08 mA AC
• Signal 0 • < 0.06 mA DC • < 0.06 mA DC
• Signal 1 • > 0.13 mA DC • > 0.13 mA DC
Delay time at 0 to 1:
• 120 VAC • Typ. 40 ms • Typ. 40 ms
• 240 VAC • Typ. 30 ms • Typ. 30 ms
• 120 VDC • Typ. 25 ms • Typ. 25 ms
• 240 VDC • Typ. 20 ms • Typ. 20 ms

Delay time at 1 to 0:
• 120 VAC • Typ. 45 ms • Typ. 45 ms
• 240 VAC • Typ. 70 ms • Typ. 70 ms
• 120 VDC • Typ. 60 ms • Typ. 60 ms
• 240 VDC • Typ. 75 ms • Typ. 75 ms
Line length (unshielded) Max. 100 m Max. 100 m
Digital outputs
Number 4 8
Output type Relay outputs Relay outputs
Electrical isolation Yes Yes
In groups of 1 1
Control of a digital input Yes Yes
Continuous current Ith Recommended range of Recommended range of
application ≥ 100 mA at application ≥ 100 mA at
12 VAC/VDC 12 VAC/VDC
Max. 5 A per relay Max. 5 A per relay
Relay rated voltage 240 VAC/VDC 240 VAC/VDC

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 17
Technical data
4.4 Technical data: LOGO! 24...

LOGO! DM8 230R LOGO! DM16 230R

Surge current Max. 30 A Max. 30 A
Incandescent lamp load (25000
switching cycles) at:
230/240 VAC 1000 W 1000 W
115/120 VAC 500 W 500 W
Fluorescent tubes with ballast 10 x 58 W (at 230/240 VAC) 10 x 58 W (at 230/240 VAC)
(25000 switching cycles)
Fluorescent tubes, 1 x 58 W (at 230/240 VAC) 1 x 58 W (at 230/240 VAC)
conventionally compensated
(25000 switching cycles)
Fluorescent tubes, 10 x 58 W (at 230/240 VAC) 10 x 58 W (at 230/240 VAC)
uncompensated (25000
switching cycles)
Short circuit-proof cos 1 Power protection B16, 600 A Power protection B16, 600 A
Short circuit-proof cos 0.5 to 0.7 Power protection B16, 900 A Power protection B16, 900 A
Derating None; across the entire None; across the entire
temperature range temperature range
Parallel output circuits for power Not permitted Not permitted
increase
Protection of output relay (if Max. 16 A, Max. 16 A,
desired) characteristic B16 characteristic B16
Line length (unshielded) Max. 100 m Max. 100 m
Switching rate
Mechanical 10 Hz 10 Hz
Ohmic load/lamp load 2 Hz 2 Hz
Inductive load 0.5 Hz 0.5 Hz

Notice: For fluorescent lamps with capacitors, you must consider the technical data of
fluorescent lamp ballasts. If the current exceeds the maximum allowed surge current,
appropriate contactor relays must switch the fluorescent lamps.
The data was determined with the following devices:
Notice: Output: B300, R300; 5A, 24VDC, G,P.; 5A, 240 VAC, G.P.; 3A, 120VAC, Tungsten.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 uncompensated.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 parallel compensated with 7 μF.
• Siemens fluorescent tubes 58 W VVG 5LZ 501 1-1N with ballast.

4.4 Technical data: LOGO! 24...

LOGO! 24CE
LOGO! 24CEo
Power supply
Input voltage 24 VDC
Permissible range 20.4 VDC to 28.8 VDC
Reverse polarity protection Yes

Product Information for LOGO! System Manual in 06/2023 edition

18 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.4 Technical data: LOGO! 24...

LOGO! 24CE
LOGO! 24CEo
Permissible mains frequency --
Power consumption from 24 VDC 25 mA to 50 mA (no load on digital output)
1.2 A (with max. load on digital output)
Voltage failure buffering --
Power loss at 24 VDC 0.6 W to 1.2 W
Backup of the real-time clock at 25 °C Typ. 20 days
Accuracy of the real-time clock Typ. ± 2 s/day
Digital inputs
Number 8
Electrical isolation No
Number of high speed inputs 4 (I3, I4, I5, I6)
Input frequency
• Normal input • Max. 4 Hz
• High speed input • Max. 5 kHz
Digital input 24 VDC
Max. continuous permissible voltage 28.8 VDC
Input voltage L+
Signal 0 < 5 VDC
Signal 1 > 12 VDC
Input current at
Signal 0 < 0.9 mA (I3 to I6)
< 0.07 mA (I1, I2, I7, I8)
Signal 1 > 2.1 mA (I3 to I6)
> 0.18 mA (I1, I2, I7, I8)
Delay time at
0 to 1 • Typ. 1.5 ms
<1.0 ms (I3 to I6)
1 to 0 • Typ. 1.5 ms
<1.0 ms (I3 to I6)
Line length (unshielded) Max. 100 m
Analog inputs
Number 4 (I1=AI3, I2=AI4, I7=AI1, I8=AI2)
Range 0 VDC to 10 VDC
Input impedance 80 kΩ
Cycle time for analog value generation 300 ms
Line length (shielded and twisted) Max. 10 m
Error limit ± 1.5% at FS
Digital outputs
Number 4
Output type Transistor,
current-sourcing 1)
Electrical isolation No
In groups of --
Control of a digital input Yes
Output voltage ≤ Supply voltage

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 19
Technical data
4.5 Technical data: LOGO! DM8 24 and LOGO! DM16 24

LOGO! 24CE
LOGO! 24CEo
Output current Max. 0.3 A per channel
Short circuit-proof and overload-proof Yes
Short circuit current limitation Approx. 1 A per channel
Derating None; across the entire temperature range
Short circuit-proof cos 1 --
Short circuit-proof cos 0.5 to 0.7 --
Parallel output circuit for power increase Not permitted
Protection of output relay (if desired) --
Line length (unshielded) Max. 100 m
Switching rate 2)
Mechanical --
Electrical 10 Hz
Ohmic load/lamp load 10 Hz
Inductive load 0.5 Hz
1) When you switch on LOGO! 24CE/24CEo, LOGO! DM8 24 or LOGO! DM16 24, the CPU sends signal
1 to the digital outputs for about 50 μs. Take this into account, especially when using devices that
react to short pulses.
2) The maximum switching rate is only dependent on the switching program's cycle time.
Notice: Output: 24 VDC, 0.3 A, RES./P.D.

4.5 Technical data: LOGO! DM8 24 and LOGO! DM16 24

LOGO! DM8 24 LOGO! DM16 24

Power supply
Input voltage 24 VDC 24 VDC
Permissible range 20.4 VDC to 28.8 VDC 20.4 VDC to 28.8 VDC
Reverse polarity protection Yes Yes
Permissible mains frequency -- --
Power consumption from 25 mA to 40 mA (no load on 25 mA to 50 mA (no load on
24 VDC digital output) digital output)
1.2 A (with max. load on digital 2.4 A (with max. load on digital
output) output)
Power loss at 24 V 0.6 W to 1.0 W 0.6 W to 1.2 W
Digital inputs
Number 4 8
Electrical isolation No No
Number of high speed inputs 0 0
Input frequency
• Normal input • Max. 4 Hz • Max. 4 Hz
• High speed input • -- • --
Digital input 24 VDC 24 VDC

Product Information for LOGO! System Manual in 06/2023 edition

20 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.5 Technical data: LOGO! DM8 24 and LOGO! DM16 24

LOGO! DM8 24 LOGO! DM16 24

Max. continuous permissible 28.8 VDC 28.8 VDC
voltage
Input voltage L+ L+
• Signal 0 • < 5 VDC • < 5 VDC
• Signal 1 • > 12 VDC • > 12 VDC
Input current at
• Signal 0 • < 0.88 mA • < 0.85 mA
• Signal 1 • > 2.1 mA • > 2 mA
Delay time at
• 0 to 1 • Typ. 1.5 ms • Typ. 1.5 ms
• 1 to 0 • Typ. 1.5 ms • Typ. 1.5 ms
Line length (unshielded) Max. 100 m Max. 100 m
Digital outputs
Number 4 8
Output type Transistor, Transistor,
current-sourcing 1) current-sourcing 1)
Electrical isolation No No
In groups of -- --
Control of a digital input Yes Yes
Output voltage ≤ Supply voltage ≤ Supply voltage
Output current Max. 0.3 A per channel Max. 0.3 A per channel
Short circuit-proof and Yes Yes
overload-proof
Short circuit current Approx. 1 A per channel Approx. 1 A per channel
limitation
Derating None; across the entire None; across the entire
temperature range temperature range
Short circuit-proof cos 1 -- --
Short circuit-proof cos 0.5 to -- --
0.7
Parallel output circuit for Not permitted Not permitted
power increase
Protection of output relay (if -- --
desired)
Line length (unshielded) Max. 100 m Max. 100 m
Switching rate
Mechanical -- --
Electrical 10 Hz 10 Hz
Ohmic load/lamp load 10 Hz 10 Hz
Inductive load 0.5 Hz 0.5 Hz
1) When you switch on LOGO! 24CE/24CEo, LOGO! DM8 24 or LOGO! DM16 24, the CPU sends signal
1 to the digital outputs for about 50 μs. Take this into account, especially when using devices that
react to short pulses.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 21
Technical data
4.6 Technical data: LOGO! 24RC...

Notice:
• Output of LOGO! DM8 24: 24 VDC, 0.3 A, RES./P.D.
• Output of LOGO! DM16 24: 24 VDC, 0.3 A, RES./P.D.; 3W, 24 VDC, Tungsten.

4.6 Technical data: LOGO! 24RC...

LOGO! 24RCE
LOGO! 24RCEo
Power supply
Input voltage 24 VAC/VDC
Permissible range 20.4 VAC to 26.4 VAC
20.4 VDC to 28.8 VDC
Reverse polarity protection --
Input frequency 50/60 Hz
Permissible mains frequency 47 Hz to 63 Hz
Power consumption
• 24 VAC • 60 mA to 185 mA
• 24 VDC • 25 mA to 100 mA
Voltage failure buffering Typ. 5 ms
Power loss
• 24 VAC • 1.4 W to 4.4 W
• 24 VDC • 0.6 W to 2.4 W
Backup of the real-time clock at 25 °C Typ. 20 days
Accuracy of the real-time clock Typ. ± 2 s/day
Digital inputs
Number 8, optional positive voltage or negative voltage
Electrical isolation No
Number of high speed inputs 0
Input frequency
• Normal input • Max. 4 Hz
• High speed input • --
Digital input 24 VAC/DC, 50/60 Hz
Max. continuous permissible voltage 26.4 VAC
28.8 VDC
Input voltage L
• Signal 0 • < 5 VAC/VDC
• Signal 1 • > 12 VAC/VDC
Input current at
• Signal 0 • < 1.2 mA
• Signal 1 • > 2.6 mA

Product Information for LOGO! System Manual in 06/2023 edition

22 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.6 Technical data: LOGO! 24RC...

LOGO! 24RCE
LOGO! 24RCEo
Delay time at
• 0 to 1 • Typ. 1.5 ms
• 1 to 0 • Typ. 15 ms
Line length (unshielded) Max. 100 m
Analog inputs
Number --
Range --
max. Input voltage --
Digital outputs
Number 4
Output type Relay outputs
Electrical isolation Yes
In groups of 1
Control of a digital input Yes
Continuous current Ith Recommended range of application ≥ 100 mA at
12 VAC/VDC
Max. 10 A per relay
Relay rated voltage 240 VAC/VDC
Surge current Max. 30 A
Incandescent lamp load (25000 switching 1000 W
cycles) at
Fluorescent tubes with ballast (25000 10 x 58 W
switching cycles)
Fluorescent tubes, conventionally 1 x 58 W
compensated (25000 switching cycles)
Fluorescent tubes, uncompensated (25000 10 x 58 W
switching cycles)
Derating None; across the entire temperature range
Short circuit-proof cos 1 Power protection B16, 600 A
Short circuit-proof cos 0.5 to 0.7 Power protection B16, 900 A
Parallel output circuits for power increase Not permitted
Protection of output relay Max. 16 A,
(if desired) characteristic B16
Line length (unshielded) Max. 100 m
Switching rate
Mechanical 10 Hz
Ohmic load/lamp load 2 Hz
Inductive load 0.5 Hz

Notice: For fluorescent lamps with capacitors, you must consider the technical data of
fluorescent lamp ballasts. If the current exceeds the maximum allowed surge current,
appropriate contactor relays must switch the fluorescent lamps.
Notice: Output: B300, R300; 8A, 24 VDC, G.P.; 10A, 24 VAC, G,P.; 3A, 120 VAC, Tungsten.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 23
Technical data
4.7 Technical data: LOGO! DM8 24R and LOGO! DM16 24R

The data was determined with the following devices:

• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 uncompensated.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 parallel compensated with 7 μF.
• Siemens fluorescent tubes 58 W VVG 5LZ 501 1-1N with ballast.

4.7 Technical data: LOGO! DM8 24R and LOGO! DM16 24R

LOGO! DM8 24R LOGO! DM16 24R

Power supply
Input voltage 24 VAC/VDC 24 VDC
Permissible range 20.4 VAC to 26.4 VAC
20.4 VDC to 28.8 VDC 20.4 VDC to 28.8 VDC
Reverse polarity protection -- Yes
Input frequency 50/60 Hz --
Permissible mains frequency 47 Hz to 63 Hz --
Power consumption
• 24 VAC • 40 mA to 110 mA • --
• 24 VDC • 15 mA to 50 mA • 30 mA to 115 mA
Voltage failure buffering Typ. 5 ms Typ. 5 ms
Power loss
• 24 VAC • 1.0 W to 2.6 W • --
• 24 VDC • 0.4 W to 1.2 W • 0.7 W to 2.8 W
Digital inputs
Number 4, optional positive voltage or 8
negative voltage
Electrical isolation No No
Number of high speed inputs 0 0
Input frequency
• Normal input • Max. 4 Hz • Max. 4 Hz
• High speed input • -- • --
Digital input 24 VAC/DC, 50/60 Hz 24 VDC
Max. continuous permissible • 26.4 VAC • --
voltage
• 28.8 VDC • 28.8 VDC
Input voltage L
• Signal 0 • < 5 VAC/VDC • < 5 VDC
• Signal 1 • > 12 VAC/VDC • > 12 VDC
Input current at
• Signal 0 • < 1.1 mA • < 0.85 mA
• Signal 1 • > 2.63 mA • > 2.0 mA

Product Information for LOGO! System Manual in 06/2023 edition

24 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.7 Technical data: LOGO! DM8 24R and LOGO! DM16 24R

LOGO! DM8 24R LOGO! DM16 24R

Delay time at
• 0 to 1 • Typ. 1.5 ms • Typ. 1.5 ms
• 1 to 0 • Typ. 15 ms • Typ. 1.5 ms
Line length (unshielded) Max. 100 m Max. 100 m
Digital outputs
Number 4 8
Output type Relay outputs Relay outputs
Electrical isolation Yes Yes
In groups of 1 1
Control of a digital input Yes Yes
Continuous current Ith Recommended range of Recommended range of
application ≥ 100 mA at application ≥ 100 mA at
12 VAC/VDC 12 VAC/VDC
Max. 5 A per relay Max. 5 A per relay
Relay rated voltage 240 VAC/VDC 240 VAC/VDC
Surge current Max. 30 A Max. 30 A
Incandescent lamp load (25000 1000 W 1000 W
switching cycles) at
Fluorescent tubes with ballast 10 x 58 W 10 x 58 W
(25000 switching cycles)
Fluorescent tubes, 1 x 58 W 1 x 58 W
conventionally compensated
(25000 switching cycles)
Fluorescent tubes, 10 x 58 W 10 x 58 W
uncompensated (25000
switching cycles)
Derating None; across the entire None; across the entire
temperature range temperature range
Short circuit-proof cos 1 Power protection B16, 600 A Power protection B16, 600 A
Short circuit-proof cos 0.5 to 0.7 Power protection B16, 900 A Power protection B16, 900 A
Parallel output circuits for power Not permitted Not permitted
increase
Protection of output relay (if Max. 16 A, Max. 16 A,
desired) characteristic B16 characteristic B16
Line length (unshielded) Max. 100 m Max. 100 m
Switching rate
Mechanical 10 Hz 10 Hz
Ohmic load/lamp load 2 Hz 2 Hz
Inductive load 0.5 Hz 0.5 Hz

Notice: For fluorescent lamps with capacitors, you must consider the technical data of
fluorescent lamp ballasts. If the current exceeds the maximum allowed surge current,
appropriate contactor relays must switch the fluorescent lamps.
Notice: Output: B300, R300; 5A, 24 VDC, G.P.; 5A, 240 VAC, G.P.; 3A, 120 VAC, Tungsten.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 25
Technical data
4.8 Technical data: LOGO! 12/24... LOGO! DM8 12/24R

The data was determined with the following devices:

• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 uncompensated.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 parallel compensated with 7 μF.
• Siemens fluorescent tubes 58 W VVG 5LZ 501 1-1N with ballast.

4.8 Technical data: LOGO! 12/24... LOGO! DM8 12/24R

LOGO! 12/24RCEo LOGO! DM8 12/24R

LOGO! 12/24RCE
Power supply
Input voltage 12/24 VDC 12/24 VDC
Permissible range 10.8 VDC to 28.8 VDC 10.8 VDC to 28.8 VDC
Reverse polarity protection Yes Yes
Power consumption
• 12 VDC • 50 mA to 165 mA • 20 mA to 90 mA
• 24 VDC • 25 mA to 90 mA • 15 mA to 50 mA
Voltage failure buffering
• 12 VDC • Typ. 2 ms • Typ. 2 ms
• 24 VDC • Typ. 5 ms • Typ. 5 ms
Power loss
• 12 VDC • 0.6 W to 2.0 W • 0.2 W to 1.1 W
• 24 VDC • 0.6 W to 2.2 W • 0.4 W to 1.2 W
Backup of the real-time clock at Typ. 20 days --
25 °C
Accuracy of the real-time clock Typ. ± 2 s/day --
Electrical isolation No No
Digital inputs
Number 8 4
Electrical isolation No No
Number of high speed inputs 4 (I3, I4, I5, I6) 0
Input frequency
• Normal input • Max. 4 Hz • Max. 4 Hz
• High speed input • Max. 5 kHz • --
Digital input 12/24 VDC 12/24 VDC
Max. continuous permissible 28.8 VDC 28.8 VDC
voltage
Input voltage L+
• Signal 0 • < 5 VDC • < 5 VDC
• Signal 1 • > 8.5 VDC • > 8.5 VDC

Product Information for LOGO! System Manual in 06/2023 edition

26 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.8 Technical data: LOGO! 12/24... LOGO! DM8 12/24R

LOGO! 12/24RCEo LOGO! DM8 12/24R

LOGO! 12/24RCE
Input current at
• Signal 0 < 0.88 mA (I3 to I6) < 0.88 mA
< 0.07 mA (I1, I2, I7, I8)
> 1.5 mA (I3 to I6) > 1.5 mA
• Signal 1 > 0.12 mA (I1, I2, I7, I8)
Delay time at
• 0 to 1 • Typ. 1.5 ms • Typ. 1.5 ms
<1.0 ms (I3 to I6)
• 1 to 0 • Typ. 1.5 ms • Typ. 1.5 ms
<1.0 ms (I3 to I6)
Line length (unshielded) Max. 100 m Max. 100 m
Analog inputs
Number 4 (I1=AI3, I2=AI4, I7=AI1, I8=AI2) - -
Range 0 VDC to 10 VDC --
Input impedance 80 kΩ
Cycle time for analog value 300 ms --
generation
Line length (shielded and Max. 10 m --
twisted)
Error limit ± 1.5% at FS --
Digital outputs
Number 4 4
Output type Relay outputs Relay outputs
Electrical isolation Yes Yes
In groups of 1 1
Control of a digital input Yes Yes
Continuous current Ith (per terminal) Recommended range of Recommended range of
application ≥ 100 mA at application ≥ 100 mA at
12 VAC/VDC 12 VAC/VDC
Max. 10 A per relay Max. 5 A per relay
Relay rated voltage 240 VAC/VDC 240 VAC/VDC
Surge current Max. 30 A Max. 30 A
Incandescent lamp load (25000 1000 W 1000 W
switching cycles) at
Fluorescent tubes with ballast 10 x 58 W 10 x 58 W
(25000 switching cycles)
Fluorescent tubes, 1 x 58 W 1 x 58 W
conventionally compensated
(25000 switching cycles)
Fluorescent tubes, 10 x 58 W 10 x 58 W
uncompensated (25000
switching cycles)
Derating None; across the entire None; across the entire
temperature range temperature range
Short circuit-proof cos 1 Power protection B16, 600 A Power protection B16, 600 A
Short circuit-proof cos 0.5 to 0.7 Power protection B16, 900 A Power protection B16, 900 A
Parallel output circuits for power Not permitted Not permitted
increase

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 27
Technical data
4.9 Technical data: LOGO! TDE (Text Display with Ethernet interfaces)

LOGO! 12/24RCEo LOGO! DM8 12/24R

LOGO! 12/24RCE
Protection of output relay Max. 16 A, Max. 16 A,
(if desired) characteristic B16 characteristic B16
Line length (unshielded) Max. 100 m Max. 100 m
Switching rate
Mechanical 10 Hz 10 Hz
Ohmic load/lamp load 2 Hz 2 Hz
Inductive load 0.5 Hz 0.5 Hz

Notice: For fluorescent lamps with capacitors, you must consider the technical data of
fluorescent lamp ballasts. If the current exceeds the maximum allowed surge current,
appropriate contactor relays must switch the fluorescent lamps.
Notice:
• Output of LOGO! 12/24RCE/RCEo: B300, R300; 8A, 24 VDC, G.P.; 10A, 240 VAC, G.P.; 3A,
120 VAC, Tungsten.
• Output of LOGO! DM8 12/24R: B300, R300; 5A, 24 VDC, G.P.; 5A, 240 VAC, G.P.; 3A, 120
VAC, Tungsten.
The data was determined with the following devices:
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 uncompensated.
• Siemens fluorescent tubes 58 W VVG 5LZ 583 3-1 parallel compensated with 7 μF.
• Siemens fluorescent tubes 58 W VVG 5LZ 501 1-1N with ballast.

4.9 Technical data: LOGO! TDE (Text Display with Ethernet

interfaces)

LOGO! TDE
Mechanical data
Keyboard Membrane keypad with 10 keys
Display FSTN-Graphic Display with 160 x 96 (columns x rows), LED
backlight (white/amber/red)
Power supply
Input voltage 24 VAC/VDC
12 VDC
Permissible range 20.4 VAC to 26.4 VAC
10.2 VDC to 28.8 VDC
Input frequency 50/60 Hz
Permissible mains frequency 47Hz to 63 Hz
Power consumption (Ethernet and
white backlight active)
• 12 VDC • Typ. 150 mA
• 24 VDC • Typ. 75 mA
• 24 VAC • Typ. 145 mA

Product Information for LOGO! System Manual in 06/2023 edition

28 Product Information, 05/2024, A5E53808149-AA
 Technical data
4.9 Technical data: LOGO! TDE (Text Display with Ethernet interfaces)

LOGO! TDE
Degree of protection
IP20 for LOGO! TDE excluding front panel
IP65 for LOGO! TDE front panel
Enclosure type Type 4X/12 for LOGO! TDE front panel
Communication port
Ethernet performance Two Ethernet interfaces with 10/100 M full/half duplex data
transmission rate
Connection distance Max. 30 m
LCD Display and Backlight
Backlight lifetime 1) 20,000 hours
Display lifetime 2) 50,000 hours
Mounting
Mounting hole dimensions (WxH) (119 + 0.5 mm) x (78.5 + 0.5 mm)
Mounting conditions Mount the LOGO! TDE vertically on a flat surface of an IP 65
or Type 4x/12 enclosure.
1) The backlight lifetime is when the final brightness is 50% of the original brightness.
2) The display lifetime is calculated under ordinary operating and storage conditions: room
temperature (20 ± 8 °C), normal humidity below 65% relative humidity, and not in exposure to
direct sunlight.

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 29
LOGO! power modules order number 5
Accessories Designation Order number
LOGO!POWER 5 V / 3 A 6EP3310-6SB00-0AY0
LOGO!POWER 5 V / 6.3 A 6EP3311-6SB00-0AY0
LOGO!POWER 12 V / 0.9 A 6EP3320-6SB00-0AY0
OGO!POWER 12 V / 1.9 A 6EP3321-6SB00-0AY0
LOGO!POWER 12 V / 4.5 A 6EP3322-6SB00-0AY0
Power modules LOGO!POWER 15 V / 1.9 A 6EP3321-6SB10-0AY0
LOGO!POWER 15 V / 4 A 6EP3322-6SB10-0AY0
LOGO!POWER 24 V / 0.6 A 6EP3330-6SB00-0AY0
LOGO!POWER 24 V / 1.3 A 6EP3331-6SB00-0AY0
LOGO!POWER 24 V / 2.5 A 6EP3332-6SB00-0AY0
LOGO!POWER 24 V / 4 A 6EP3333-6SB00-0AY0
LOGO!POWER EX 24 V / 4 A 6EP3333-6SC00-0AY0

30 Product Information, 05/2024, A5E53808149-AA

Index

A
Approval
CCCEx, 8
FM, 8

C
CCCEx, 8
Certification and approvals
CE label, 6
cFMus, 5
C-tick label, 6
cULus, 5
KCC label, 6

E
EAC, 8

F
Factory reset, 9
FM, 8

L
LOGO! TDE
backlight lifetime
display lifetime
LCD lifetime, 29

R
Recycling and disposal, 10

U
UKCA, 7

Product Information for LOGO! System Manual in 06/2023 edition

Product Information, 05/2024, A5E53808149-AA 31