11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?

OpenDocument

DURABLE PORTFOLIO

Product Data Sheet

Fasson® 2 Mil White Polyester TC/S8025/50#SCK Spec#: 77920 Durable

Facestock Facestock physical properties

2 Mil White Polyester TC is a Imperial Value Units Metric Value Units
homogeneously pigmented white Caliper: 0,0020 inches 50,80 micron
facestock featuring excellent tear ASTM D1000
strength, heat resistance,
dimensional stability, opacity, and Tensile: MD 21.300 PSI 1.497 kg/cm2
chemical resistance. ASTM D882 CD 28.400 PSI 1.997 kg/cm2

Adhesive Adhesive physical properties

S8025 is a high performance, clear Imperial Value Units Metric Value Units
permanent solvent acrylic pressure Type: Solvent Acrylic
sensitive adhesive with balanced
adhesion to a wide variety of Caliper: 0,0009 Inches 22,86 microns
substrates, including low surface ASTM D1000
energy plastics, engineering grade
plastics, bare, coated, or painted Standard Coat Wt: 27 g/sq m
metals, including powder coat and Minimum Appl Temp: 50 F 10 C
enamel paints. It features medium
Service Temp Min -40 F -40 C
tack for good short term
Range:
repositionability, low ooze, and Max 302 F 150 C
excellent chemical and UV Loop Tack Stainless 50,6 oz/in 55,7 N/100 mm
resistance for outdoor industrial Steel: PSTC11
applications.

Liner Liner physical properties

50#SCK is a bleached, super- Imperial Value Units Metric Value Units
calendered paper stock with very Caliper: 0,0032 inches 81,2800 microns
good diecutting and matrix stripping ASTM D1000
properties. Suitable for back-printing Basis Wt: TAPPI T410 53,9 lb/ream 86,2 g/sq m
with standard inks. * (24" x 36" 500 sheets)
Tensile: MD 48,0 lb/inch 211,2 N/25 mm
ASTM D882 CD 26,0 lb/inch 114,4 N/25 mm
Tear: MD 1,8 ounces 51,1 grams
TAPPI T414 CD 2,0 ounces 56,8 grams

Liner Release: Total Construction Caliper

TMLI 90o removal of Liner from Facestock. (approximate):
Rate of Removal Grams/2" Width
400 inches/min. 55 0.0062 inches (6.2 mils; 154.9 microns)

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 1/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument

DURABLE PORTFOLIO

Product Data Sheet

Features and Benefits

Opaque white facestock with very good hiding power and physical strength
Glossy clear topcoat which accepts most flexographic, letterpress, and rotary screen inks
Excellent thermal transfer printability with most wax/resin and resin ribbons
Topcoat and adhesive have excellent chemical resistance

Applications and Uses

This product is suitable for wide variety of durable labeling applications such as:

Product identification labels

Barcodes and rating plates
Work in progress labels (WIP)
Property identification and asset tags
Durable goods labeling
For safety-critical medical devices, labeling to IEC 60601 standards helps to ensure the safety and
effectiveness of a device
UL and UL-c recognized for indoor and outdoor use. Specific recognition information will be found in UL file #
MH17205.

Printing and Converting

The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks; UV cured letterpress and
rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink
system selections. The following press inks are UL Recognized at 150ºC (302ºF) without the need for overlaminations. Color
recognitions or restrictions and additional chemical resistances are noted for each ink system:
► Water-based flexogrphic inks with lube oil resistance: Environmental Inks & Coatings' "DR III FR" {recognized in all colors
for indoor use, blue and black for outdoor use}, "Aqua Plus" and "Aqua Film III" {recognized for indoor use in blue, black, and
red, for outdoor use in blue and black}; Flint Ink's "HydroFilm ACE" {recognized in blue, black, and red for indoor and outdoor
use}; and ACTEGA WIT, Inc. "Versifilm Plus ULF" {recognized in all colors for indoor and outdoor use}, and "Water Gloss"
{recognized in all colors for indoor and outdoor use}.
► UV flexographic inks with lube oil and gas splash resistance: Environmental Inks & Coatings' "UltraFlex III SFR"
{recognized in all colors for indoor use; blue, black and red for outdoor use}; Flint Ink's "Flexocure Sigma" {recognized in all
colors for indoor use; blue, black and red for outdoor use or with gasoline}; and ACTEGA WIT, Inc. "PharmaFlex UV"
{recognized in blue, black, and red for indoors and outdoor use}.
► UV ink jet: EFI Jetrion 4000 series {recognized with lube oil and gas splash resistance in all colors for indoor and outdoor
use}.

Note: With most press inks, overlamination is required to meet the abrasion requirement for c-UL (CSA) recognition. At the
150ºC recognition temperature, overlaminations darken enough to hinder the readability of most yellow colored inks. If
overlamination is desired with UL or c-UL recognition, seek recognition at a lower maximum use temperature.

Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson
Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on
most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard
labeling systems.

RoHS/Regulation 2002/95/EU
The substances listed in article 4 lid 1 of 2002/95/EU (RoHS) are not intentionally used in this product. The concentration
limits of these substances will not exceed the set maximum concentration limits as provided in the proposed amendment for
2002/95/EU.

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 2/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument

Optimal Storage Conditions

Unless otherwise specified in this document, ideally store at 72F and 50% RH

Note:
The technical data presented is from tests we believe to be reliable but should be considered representative or typical only
and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to
ensure it meets the requirements of the specific application.

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 3/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument

DURABLE PORTFOLIO

Product Data Sheet

Appendix
Performance Data:
The following technical data should be considered representative or typical only and should not be used for specification
purposes.

Initial 72 Hours at Room 72 Hours at 1200F 96 Hours at 1500F

(15 minute dwell) Temperature
(650C) &
80% Relative Humidity
Surface oz/in N/100mm oz/in N/100mm oz/in N/100mm oz/in N/100mm
1. Stainless Steel 62.7 69 65.8 72.4 75.2 82.7 89.6 98.6

2. Aluminum 42.7 47 52.8 58.1 67.2 73.9 85.1 93.6

3. Polypropylene 52.3 57.5 62.9 69.2 59.2 65.1 57.9 63.7

4. HDPE 32 35.2 32 35.2 36.8 40.5 36.3 39.9

5. LDPE 24.8 27.3 42.1 46.3 35.4 38.9 23.7 26.1

6. ABS Plastic 56.2 61.8 65.6 72.2 56 61.6 54.7 60.2

Environmental Performance: Chemical Resistance test results

The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour).
Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately
upon removal. Adhesion measured at 180° peel.

Adhesion to Stainless Steel Visual Edge

Chemical oz/in N/100mm Appearance Penetration mm
1. 70% IPA 43 47.3 No Change 0

2. Tide® Detergent 57.9 63.7 No Change 0

3. Engine Oil (10W30) 53.6 59 No Change 0

4. Water 60 66 No Change 0

5. Ammonia - pH 11 42.4 46.6 Edge Swell 0

6. 409® Cleaner 56.2 61.8 No Change 0

7. Toluene 29.4 32.3 Edge Swell 6.4

8. Brake Fluid 51 56.1 No Change 0

9. Reference Fuel C 48.8 53.7 Edge Swell 0

10. Kerosene K1 56.5 62.2 No Change 0

11. Heptane 43 47.3 No Change 0

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 4/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument

Compliance Recognition: UL, C-U

Underwriters Laboratories, Inc.

Minimum Temperature Maximum Temperature
Substrates oF oC oF oC (I=Indoor Only
I/O=Indoor &
Outdoor)
1. Acrylic Paint -40 -40 302 150 I/O

2. Alkyd Enamel -40 -40 302 150 I/O

3. Aluminum -40 -40 302 150 I/O

4. Epoxy Paint -40 -40 302 150 I/O

5. Galvanized Steel -40 -40 302 150 I/O

6. Polyester Paint -40 -40 302 150 I/O

7. Polyester PCP* -40 -40 302 150 I/O

8. Polyurethane PCP* -40 -40 302 150 I/O

9. Porcelain -40 -40 302 150 I/O

10. Stainless Steel -40 -40 302 150 I/O

11. Epoxy PCP* -40 -40 302 150 I/O

12. Melamine -40 -40 212 100 I/O

13. Nylon -40 -40 212 100 I/O

14. Polycarbonate -40 -40 212 100 I/O

15. Thermoset Polyester -40 -40 212 100 I/O

16. ABS Plastic -40 -40 176 80 I/O

17. PBT Plastic -40 -40 176 80 I/O

18. Polystyrene -40 -40 176 80 I/O

19. Polyphenylene -40 -40 176 80 I/O

Oxide
-40 -40 176 80 I/O
20. Polypropylene

21. and others

22. *PCP=Powder Coat

Paint

Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med Inc "R-5", Astro Med "RF", Astro Med
"RY", Coding Prds "5940", Dai Nippon "R-300", Dai Nippon "R-510", Iimak "SP-410", Iimak "SP-330",
Iimak "Primemark", Intermec "TMX 1500", Intermec "TMX 3200", ITW "B324", Kurz "K300", Kurz
"K500", Kurz "K501", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR
"K3", Ricoh "B110C", Ricoh "B110CR", Ricoh "120EC", Sato Corp. "Premier 1", Sony "TR4070",
Sony "TR4075", Sony "TR5070", Sony "TR6070", Sony "TR6075", Sony "TRX75", Sony "Signature

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 5/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument

Series Resin", Union Chemicar "US300", Zebra "5095", Zebra "5100", Zebra "5175", Zebra "5463",
Zebra "5555", Zebra "Z-4100", and others.

Tested by Underwriters Laboratories, Inc.

to meet the requirements of the Canadian Standards Association for labeling
materials
Minimum Temperature Maximum Temperature
Substrates oF oC oF oC (I=Indoor Only
I/O=Indoor &
Outdoor)
1. Metals -40 -40 302 150 I/O

2. Electrostatic Paints -40 -40 302 150 I/O

3. Plastics Group I -40 -40 212 100 I/O

4. Plastics Group II -40 -40 176 80 I/O

5. Plastics Group III -40 -40 176 80 I/O

6. Plastics Group IV -40 -40 176 80 I/O

7. Plastics Group V -40 -40 176 80 I/O

8. Plastics Group VI -40 -40 176 80 I/O

9. Plastics Group VII -40 -40 176 80 I/O

10. Plastics Group VIII -40 -40 176 80 I/O

Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR600", Astro Med "RY", Dai Nippon "R-300", Dai Nippon
"R-510", Kurz "K500", NCR "Promark 3", Ricoh "B110C", Ricoh "B110CR", Sato Corp. "Premier 1",
Sony "TR4070", Sony "TR5070", Sony "TRX75", Sony "Signature Series Resin", Union Chemicar
"US300", Zebra "5100", and others.

409® is a registered trademark of the Clorox Company

Tide® is a registered trademark of the Procter & Gamble Company

The information on compliance conditions, substrates, and printing products contained in the tables above represent a
summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products
may be recognized with this material. Please consult the specific compliance organization records or specific files for a
complete listing.

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 6/7
11/9/2017 Durable Form - http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument
Warranty
All sales and contracts for sale are expressly conditioned on the buyer’s assent to Avery Dennison’s terms and conditions found on its website at
www.na.fasson.com. Avery Dennison hereby objects to any term, different from or additional to Avery Dennison’s terms, contained in any buyer communication in
any form, unless agreed to in a writing signed by an officer of Avery Dennison.

www.na.fasson.com Label and Packaging Materials-North America

8080 Norton Parkway
Mentor, OH 44060
800-944-8511

http://na1.fasson.com/frna/Prod_sht.nsf/frna/Prod_sht.nsf/2049EA472D5B6599852572120044F568?OpenDocument 7/7