4th
REMOTE CONTROL RC CAR
AGES
TURBO RACING, TABLE RACING, TOP RACING
www.turboracing.net
Please read the manual before using the product and keep the manual for future use.
Safety information
● Movable parts are dangerous, so it is forbidden to put fingers、hair、clothes and other things into the
space between the tire and the car body, to avoid being clamped by the rotating parts.
● Please play the car with the following scence:
Please don’t play in places where the car is running or near children, then avoid the risk of collision.
Please don’t play it in sand、water or dust, then avoid trobule.
Please don’t play towards people or animal, then avoid accident.
● For functional requirements, this product contains sharp parts, please follow the correct steps and use
methods, pay attention to eye safety.
● Please don’t bend or throw the product or play it with rough ways, then avoid an accidents.
● Please don’t put this product into water or fire source(such as stove、gas stove,etc.), then avoid accidents.
The package contains
C10: 1*car C71: 1*car
C72: 1*car C73: 1*car C81: 1*car
1*transmitter
2
1* M1.5 Bolt driver 1*Stainless steel tweezers 1*Stainless steel brush
1*Repair bench 1*Type-C line+Bind 1*manual
Prepare for run
1. Charging
Please take out the remote control car and accessories from the box, and insert the end of the Type-C line
into the charging hole of the car and the other end of the Type-C line connect the power source, please
make sure the switch is off. Pay attention please, you must be charging if you play the car with the first time.
Tip: if the charging indicator light is on for a long time, it indicates that
charging is in progress,If the indicator light goes out, it indicates
that the charging is completed.
Tips: if the switch is on, it will not be charged; the switch must be in Red light
off if you charging.
Note: Before charging the car, make sure the charging plug is dry.
Do not leave when charging the car. Extinguish
3
2. Turn on/off the power of the car
Power ON: Switch on the power supply of the car. The car is power on when the LED light starts flashing.
Switch power
If the rear light of the car stays on, it indicates that it’s connected with the remote control.
If the rear light of the car is flashing, please check whether the power of remote control has
been turned on. If yes, you need to re-code the remote control with the car. (See page 6 for details)
Turn off the car: Turn off the power switch, (switch to "OFF" position), the LED goes off and the the car is power off.
3. Transmitter battery installation
Tip: instructions for safe use of replaceable battery of remote control:
1. Non rechargeable batteries cannot be charged; rechargeable batteries can only be charged under the
supervision of adults.
2. Before charging, the rechargeable battery should be taken out from the remote control; different types
of batteries or old and new batteries cannot be mixed.
3. The battery shall be placed in the correct polarity; the exhausted battery shall be taken out of the remote
control; the power terminal shall not be short circuited.
Battery installation
4x 1.5V (AAA) Use AAA*4 or NIMH battery, when the voltage is lower
than 4.5V±0.2V, the transmitter’s LED will start flashing.
1. Remove the battery cover from the transmitter.
2. Install four new AAA batteries according to the polarity
markings on the battery holder.
3. Reinstall the battery cover.
WARMING :DO NOT KEEP THE BATTERY IN THE
BATTERY COMPARTMENT FOR A LONG TIME TO
AVOID BATTERY OXIDATION AND DAMAGE THE
PRODUCT.
4
Operation Note
Note: If you’re the first time to use the 1:76 RC sports car, please take a few minutes to read this statement
carefully to get familiar with different features of this operation system.
1 Functions Transmitter
Antenna
Steering wheel
ST trim+
LCD Display
ST trim-
+ button - button
SEL/CH
Throttle trigger CH3
Power
Disassemble key
Bat box
2� � � � � � Install and remove the remote
control handle
1. Press the button
2. Remove the handle
3. Press and hold the remove button and
push the handle inside
Tips: Pay attention to the direction of the handle
5
BIND
3 Binding
1.Switch on the transmitter. 2.Turn on the power switch on the 3.Insert the binding plug into the BIND
car, and the rear light on the channel slot on the car, if the LED rear
car flashes. light , and stays lit permanently, the
binding procedure is completed.
Tip: If fail binding , please turn off the power switch of the car and remote , and restart the binding.
Note: The wireless rc car has been connected to the remote. The above procedure is only necessary when use a
new remote or car.
Turn off the car: Please turn off the power switch of the car first, and then turn off the power switch of the remote
to prevent the car from losing control.
2 Car running settings
Neutral Forward/speed up
Left Right
Left Right
Backward/speed up
Neutral
Forward/
speed up
Backward/speed up
ST trim+
ST trim-
Linearity
6
5 LED FUNCTION DISPLAY
CH4 M: M means that the front and rear
lights are on for a long time
CH4 L: L stands for turning off the front
and rear lights
CH4 H: H represents that the headlights
flash twice
7
A) MODEL SELECT
• This transmitter can store 15 sets of models (01-15) to adapt different model
products to quickly invoke saved Settings.
1. Press the "sel / CH" button to enter the model option setting ("000 01" mode).
2. Press the "+" key or "-" key to select the mode option and set it.
B) REV
• This function is used for correct the control direction of servo or motor.
1. Press "set / CH" button to enter rev-st setting.
2. Press + / - key to select off or on.
3. Long press the "set / CH" button to switch to the next channel: rev-th,
rev-3c, rev-4c, and repeat the above steps to set off or on.
C) EPA
• This function is used for set the maximum servo travel limiter of each channel and
adjust the maximum servo travel limiter according to the model structure.
1. Press "set / CH" button to enter epa-st setting.
2. Press + / - key to set the rudder at 0-120%.
3. Long press the "set / CH" button to switch to the next channel: epa-th, epa-3c,
epa-4c. Repeat the above steps 0-120% rudder capacity.
D) ABS
• ABS is used to set the automatic braking (snub) of the throttle output channel to
achieve the best braking effect and the control effect of turning corners without
tail flicking and insufficient turning.
1. Press the "set / CH" button to enter abs-th
2. Press + / - key to turn on or off (off / on).
8
E) EXP
• Exp is used to adjust exp-st (steering), exp-fw (forward) and exp-bk (backward) curves,
and the adjustment range is between 0% - 100%; When the value is 0%, the curve is
linear, and the curve can be set to positive or negative value. A positive value will reduce
the sensitivity near and increase the sensitivity at both ends, while a negative value will
increase the sensitivity near the median and reduce the sensitivity at both ends.
1. Press the "set / CH" button to enter exp-st.
2. Press + / - key to set between 0-100%.
3. Long press the "set / CH" button to switch to the next channel: exp-th, exp-bk. repeat
the above steps to set the 0-100% curve.
F) TRIM
• This function is used to adjust the moddle position of the throttle.CH3. CH4.
1. Press the "set / CH" button to enter trim-st, and long press the "set / CH" button to
select the channel to be adjusted.
2. Press + / - key to set between 0-100%.
3. A steering fine adjustment shortcut key is set outside the remote control for rapid
adjustment.
G) SVC
• The smart vehicle control function can use for the gyroscope of the receiver to control
the direction of the vehicle intelligently, which can guarantee the vehicle to run
normally in the expected direction even in the case of road bumps or sharp turns.
1. Press the "set / CH" button to enter svc-01.
2. Press + / - key to switch svc-01 / svc-02 switch.
H) D/R
• DR function is used for adjust the maximum value at both ends of the channel, and to
reduce or enlarge at the same rate. Default 100% maximum.
1. Press "set / CH" button to enter D / r-st.
2. Press + / - key to set between 0-100%.
3. Long press the "set / CH" button to select the channel to be adjusted for setting.
I) MODEL NAME
• This function is to number the name of the machine type stored by the transmitter (use 3
characters). To facilitate memory and invoking，the below characters can be used：
0-9/A-Z
1. Press the "set / CH" button to enter 000 01. You can enter characters 0-9 and A-Z through
+/-.
2. Long press the "set / CH" button to select the next character, and repeat the above steps
to select the required number or letter.
9
Precaution
● The car contains lithium batteries. Disassembling, striking, squeezing or throwing the car into the fire is
prohibited. If severe swelling occurs, do not continue to use it. Do not place it in high-temperature
environment.
● Due to the special feature of lithium batteries, overly high or low temperature will affect the battery charge
and discharge performance and battery life, so please do not use or store this product under environments
such as high temperature, low temperature, high humidity or direct sunlight.
● The charging cable, plug, body shell, and other parts must be checked regularly for damage. If the damage is
found, stop using until the repair is complete.
● The car has low battery voltage protection.
● When the battery voltage is lower than 3.0V, it will automatically cut off the current and the car will seize
all functions to protect the battery.
● When using remote control nearby high-voltage power lines, light rails, microwave ovens electric waves of
the same frequency will lead to dysfunction of the car. Please change the location or choose another time
to operate.
● Our company holds no responsibility if accidents such as injury to others or damage due to operating errors.
10
Troubleshooting
Fault symptom Cause of failure Solutions
1. Distance is too far Make sure that the product is in car
The tranmitter connection receiving mode.(The headlights flash).
failed 2. Multicars pairing at the The pairing distance is less than 2 meters
same time and only one car is paired at the same time
Foreign object between Check the wheels for foreign objects
Freeze the wheels
No reaction when remote
control left and right The steering angle is set Reset the steering angle
steering / no response too small
when steering
The steering is in the The remote steering Set the remote steering reverse switch to
opposite direction of the reverse switch is not the correct direction
remote steering operation properly set
When the throttle is in
neutral position, the car The throttle fine-tuning
does not set to the center Set the remote throttle fine-tuning to the
immediately starts to
position center position
move forward or backward
The car cannot move in a
straight line/The left and Steering fine-tuning is not Set the steering fine-tuning to the center
right steering radius is set to the center position position
significantly different
1. The throttle DR setting is
too small Set the throttle DR size on the remote
The maximum speed 2. Battery Low throttle DR, and check for foreign objects
cannot be reached 3. Foreign objects between and battery level
the wheels
The car should be immediately turned off
Ambient temperature is too and placed in a cool, well-ventilated place
Overheating in the motor high for cooling to avoid damage to electronic
part parts
The power-on light is not
on The voltage is less than
Charge in a timely manner
3.0V and there is not
enough power
Shutdown
11
Product performance failure table
Product Name Product performance failure
1. The product cannot be turned on.
1:76 Remote control car 2. Cannot charge.
3. Unable to operate.
4. Dysfunction.
Maintenance
1. Before using the product, please ensure that all components have been tightened, check and clear foreign
matter in the gap between the wheel and chassis.
2. When the car is to be stored for a long time, it should be kept at 70% of its power to maximize battery
life. And charge the battery once every 3 months to avoid battery damage. (It is recommended to fully
charge the battery and store it after 20 minutes of use).
3.If the remote control will not be used for a long time, please remove the batteries to avoid oxidation.
Non-warranty regulations
● Unauthorized repair, misuse, collision, negligence, abuse, fluid intake, accidents, alterations, incorrect use.
Non-product accessories, or tear, alter marks and anti-counterfeiting marks;
● The validity period of "three guarantees" has passed.
● Damage caused by force majeure;
● Does not meet the performance failures listed in “performance failure table of 1:76 remote control car”;
● Performance failure of the product and its accessories that meets the “performance failure table of 1:76
remote control car” due to human factors.
1. Return and exchange services require confirmation.
When the client applies for return and exchange, it is necessary to follow the smart remote-control car
warranty instructions and the customer service should confirm whether it meets the after-sales conditions
and then arrange relevant service.
Notice: The products, accessories, remote control, etc. in the instruction manual are schematic diagrams and
for reference only. Due to product updates and upgrades the physical and schematics of the product may differ
slightly, please refer to the actual product.
12
Choose a variety of styles
1 RC car
C10 C10 C10 C10
Fluorescent green Fluorescent red Cement gray Dark green
C10 C10 C10 C10
Mint green Orange Purple Light yellow
C10 C10
Light blue Blue
2� � � � � � � RC Sports car
C71-RD C71-YE C71-WH
Red Yellow White
C72 C73
Violet Cement grey
13
3� � � � � � � Off-road vehicle
C81-BK C81-YE
Black Yellow
14
Shenzhen NewStone Technology Co., Ltd.
Manufacturer: Shenzhen NewStone Technology Co., Ltd.
Address: Yuhong Industrial Park, No.20 Xingye West Road, ShaJing Town, Bao'an
District, Shenzhen, Guangdong Province
If this product can not operate normally during the warranty period, please
contact the local distributor or manufacturer that sold this product to obtain
warranty service. When the product is under warranty, please show the product
warranty card and proof of whether it is within the warranty period.
1. If your product was sold by a distributor, please consult with the distributor
or manufacturer to resolve it. (It is recommended to negotiate with the local
distributor)
2. Manufacturers have the responsibility to "repair" or "replace" the product.
3. The warranty period of all products provided by the manufacturer is 15 days.
4. When the product is under warranty, manufacturers and distributors have the
responsibility to "repair" or "replace" the product.
www.turboracing.net
