SOLENOID VALVES 1

3/2
no voltage release (lever type) U Series
manual reset construction 3 2
307
1/4 to 1/2
FEATURES
● Lever type Manual Reset function which means that the valve has to be energized
as well as manually operated before it stays in the "latched" position
● The No Voltage Release (NVR) function will make sure that the valve trips when
de-energized
● The solenoid valves are recommended for 3/2 way pilot applications with full flow
and wide pressure ranges
● Stainless steel or brass bodied valves with stainless steel internal parts
● The use of first class materials and thorough valves testing ensure a high
reliability and a long service life
● The solenoid valves satisfy all relevant EC Directives

GENERAL
Differential pressure 0 - 10 bar [1 bar = 100kPa]
Maximum viscosity 65cST (mm2/s)
Response times 75 - 100 ms
fluids () temperature range (TS) seal material ()
air, inert gas - 38°C to + 60°C NBR (nitrile)

MATERIALS IN CONTACT WITH FLUID

() Ensure that the compatibility of the fluids in contact with the materials is verified
Brass body Stainless steel body
Body Brass AISI 316 SS
Core tube Stainless steel Stainless steel
Core and plugnut Stainless steel Stainless steel
Springs Stainless steel Stainless steel
Seals NBR NBR
Disc and poppets NBR NBR
Seat Brass Stainless steel

BP
MP
RP
LP
Not Not
0,4W - 1,7W Available Available 16,7W-22,6W

Low Reduced Medium Basic

power power power power

POWER LEVELS - cold electrical holding values (watt)

SPECIFICATIONS
operating pressure
flow prefix optional solenoids basic
pipe orifice differential (bar) power
coefficient catalogue
size size min. max. (PS) level NEMA ATEX / IECEx
Kv IP65 number
air () 7&9 Ex d Ex e mb Ex mb Ex ia
Npt (mm) (m3/h) (l/min) ~/= ~/= EF NF EM PV IS SC brass stainless st.
3/2 - U - Universal, single solenoid, manual reset (NVR)
1/4 9,0 0,68 11,3 0,0 10,0 LP - -  -   B307A416 B307A406
1/4 9,0 0,68 11,3 0,0 10,0 BP   - - -  B307B016 B307B006
3/8 9,0 0,68 11,3 0,0 10,0 LP - -  -  B307A446 B307A436
80340GB-2017/R01


3/8 9,0 0,68 11,3 0,0 10,0 BP   - - -  B307B046 B307B036
1/2 9,0 0,68 11,3 0,0 10,0 LP - -  -   B307A476 B307A466
1/2 9,0 0,68 11,3 0,0 10,0 BP   - - -  B307B076 B307B066
● Available feature  Available feature in DC only - Not available

All leaflets are available on: www.asco.com

1
 SERIES 307

PREFIX TABLE PRODUCT SELECTION GUIDE

prefix description power level STEP 1
1 2 3 4 5 6 7 LP RP MP BP Select basic catalogue number,
E F Explosionproof - NEMA 7, 9 - Zinc plated steel conduit - - - ¶ including pipe thread indentification
E V Explosionproof - NEMA 7, 9 - 316 SS conduit - - - ¶ letter. Refer to the specifications table
E M Waterproof IP66/67 - Metal enclosure (EN/IEC 60079-7,-18 and -31)*  - - -
on page 1 or 2.
E T Threaded conduit/hole (M20 x 1,5)  - - 
I S S C Intrinsically safe with SC coil (EN/IEC 60079-11+26, 61241-11)*  - - - Example: B307B016
N F Flameproof - Aluminium (EN/IEC 60079-1, 60079-31)* - - - 
S C Solenoid with spade plug connector (EN/IEC 60730)  - -  STEP 2
W P Waterproof IP67 - Metal enclosure  - -  Select prefix (combination). Refer to
W P I S I.S. with Metal IP67 enclosure (EN/IEC 60079-11+26, 61241-11)*  - - - the specifications table on page 1 and
W S Waterproof IP67 - 316 SS enclosure  - - 
the prefix table on page 2, respect the
W S E M Waterproof IP66/67 - 316 SS enclosure (EN/IEC 60079-7,-18 and -31)*  - - -
W S I S I.S. with 316 SS IP67 enclosure (EN/IEC 60079-11+26, 61241-11)*  - - - indicated power level.
W S N F Flameproof - 316L SS (EN/IEC 60079-1, 60079-31)* - - -  Example: EMET
T Threaded conduit (1/2" NPT)  - - 
H C Class H - Battery charging circuit - - -  STEP 3
H T Class H - High temperature - - -  Select suffix (combination) if required.
X Other special constructions  - -  Refer to the suffix table on page 2,
SUFFIX TABLE respect the indicated power level.
Example: V
suffix description power level
1 2 3 4 5 LP RP MP BP STEP 4
N V FPM (fluoroelastomer) and parts cleaned for oxygen service  - -  Select voltage. Refer to standard
V FPM (fluoroelastomer)  - - 
voltages on page 3.
C O Epoxy coating on all external surfaces  - - 
M B Mounting bracket  - -  Example: 230V / 50Hz
● Available feature
 Available feature in DC only STEP 5
¶ Available feature in AC only Final catalogue / ordering number.
- Not available
* ATEX/IECEx valves using these solenoids are approved according to EN 13463-1 (non electrical)
Example:
EMET B307B016 V 230V / 50 Hz

OPTIONS & ACCESSORIES ORDERING EXAMPLES VALVES:

catalogue spare parts kit no. (1)
mouting SC B 307C009 NV 24V / DC
number ~ = bracket no. WS B 307C019 CO 24V / DC
WP B 307C039 NV 24V / DC
SC B 307B006 C115468 C115472 115292-001
SC B 307B016 C115469 C115473 115292-001 prefix voltage
SC B 307B036 C115468 C115472 115292-001 pipe thread suffix
SC B 307B046 C115469 C115473 115292-001 basic number
SC B 307B066 C115468 C115472 115292-001
SC B 307B076 C115469 C115473 115292-001
SC B 307A406 C132660 C132660 115292-001 ORDERING EXAMPLES KITS:
SC B 307A416 C132661 C132661 115292-001
C115472 (2)
SC B 307A436 C132660 C132660 115292-001
WS C115473
SC B 307A446 C132661 C132661 115292-001
WS C115469
SC B 307A466 C132660 C132660 115292-001
80340GB-2017/R01

SC B 307A476 C132661 C132661 115292-001

prefix
(1)
Standard prefixes/suffixes are also applicable to kits basic number
(2)
Basic kit number applies to SC coil construction

All leaflets are available on: www.asco.com

2
 SERIES 307

EXPLANATION OF TEMPERATURE RANGES OF SOLENOID VALVES

Valve temperature range The valve temperature range (TS) is determined by the selected seal material, the temperature
range for proper operation of the valve and sometimes by the fluid (e.g. steam)
Operator ambient temperature range The operator ambient temperature range is determined by the selected power level and the
safety code
Total temperature range The temperature range of the complete solenoid valve is determined by the limitations of both
temperature ranges above

ELECTRICAL CHARACTERISTICS
Coil insulation class F
Connector Spade plug
Connector specification ISO 4400 (cable Ø 6-10 mm)
Electrical safety IEC 335
Standard voltages: DC (=) 24V - 48V
AC (~) 24V - 48V - 115V - 230V/50 Hz; Other voltages are available on request
power ratings operator
ambient electrical replacement coil / kit
prefix inrush holding hot/cold temperature enclosure
safety code
option ~ ~ = range (TS) protection ~ = type(2)
(VA) (VA) (W) (W) (C°)(1) (EN 60529)
230V/50 Hz 24V/DC
Basic power (BP)
SC 78 35 16,7 13,5/19,7 -40 to +75 EN 60730 IP65, moulded 400-425-217 400-425-342 01
WP/WS 78 35 16,7 13,5/19,7 -40 to +75 EN 60730 IP67, steel/SS 400-405-217 400-405-342 02
NF/WSNF 78 35 16,7 13,5/19,7 -60 to +60 II2G Ex d IIC Gb T4, II2D Ex tb IIIC Db IP66/67, alu./SS 400-405-217 400-405-342 -
EF/EV 70 40 17,1 15,8/22,6 -40 to +52/40 NEMA type 7 and 9 4X, moulded 238-614-159D 274-714-106D 03
Low Power (LP)
SC 1,2 1,2 1,2 1,3/1,3 -40 to +75 EN 60730 IP65, moulded 400-929-097 400-929-042 04
WP/WS 1,2 1,2 1,2 1,3/1,3 -40 to +75 EN 60730 IP67, steel/SS 400-930-097 400-930-042 05
EM/WSEM 1,2 1,2 1,2 1,3/1,3 -40 to +60 II2G Ex e mb IIC Gb T6, II2D Ex tb IIIC Db IP66/67, steel/SS 400-930-097 400-930-042 05
ISSC - - - 0,4/0,4 -40 to +60 II1G Ex ia IIC T6, II2D Ex iaD 21 IP65, moulded - 123-256-001 04
WPIS/WSIS - - - 0,4/0,4 -40 to +60 II1G Ex ia IIC T6, II2D Ex iaD 21 IP67, steel/SS - 109-496-003 05
(1)
Temperature range can be limited by sealings (3 ) Multiple coil kits are available under ATEX/IECEx, contact us
(2)
Refer to the dimensional drawings on page 4 - Not available

ADDITIONAL OPTIONS
● Other pipe threads are available on request
● Compliance with “UL”, “CSA” and other local approvals available on request
● 1/2” NPT (prefix “T”) and M20 x 1,5 (prefix “ET”) conduits (aluminium or 316 SS) available for steel solenoid housing
● Special moulded-in solid state components for peak voltage suppression and/or rectification (four diode bridge)

INSTALLATION
● The solenoid valves have to be mounted vertically and in an upright position for best performance
● Multi language installation/maintenance instructions are included with each valve
● Threaded pipe connection identifier is B = NPT (ANSI 1.20.3)
● Other pipe threads are available on request
● Ex e mb (prefix “EM”) execution: solenoid enclosure has a cable gland with integral strain relief for cables with an o.d.
from 7 to 12 mm and is provided with an internal and external connection facility for an earthing or bonding conductor
80340GB-2017/R01

All leaflets are available on: www.asco.com

3
 SERIES 307

DIMENSIONS (mm), WEIGHT (kg)

TYPE 01: TYPE 02:

Epoxy moulded Metal, epoxy coated / AISI 316 SS
SC: IEC 335 / ISO 4400 WP / WS: IEC 335

307B006 / B016 / B036 / B046 / B066 / B076 307B006 / B016 / B036 / B046 / B066 / B076

A G
 

L
K 

E F HJ  

B C  
D 

TYPE 03: TYPE 04:

Epoxy encapsulated Epoxy moulded
EF and EV: NEMA type 7, 9 / ICS-6 ANSI SC: IEC 335 / ISO 4400
ISSC: EN/IEC 60079-11+26, 61241-11

307A406 / A416 / A436 / A446 / A466 / A476 307A406 / A416 / A436 / A446 / A466 / A476

A G A G

L L
K K

E F J H E F HJ

B C B C
D D

TYPE 05:
Metal, epoxy coated / AISI 316 SS
WP / WS: IEC 335
EM / WSEM: EN/IEC 60079-7+18+31
WPIS / WSIS: EN/IEC 60079-11+26, 61241-11

307A406 / A416 / A436 / A446 / A466 / A476

A G

KL
80340GB-2017/R01

EF HJ

B C
D

All leaflets are available on: www.asco.com

4
 SERIES 307

DIMENSIONS (mm), WEIGHT (kg)

power
type prefix option A B C D E F G H J K L weight
level
01 SC BP 128 102 25 127 27 6 132 24 30 152 180 2,5 kg
02 WP, WS BP 134 102 25 127 27 6 130 24 30 168 180 2,5 kg
03 EF, EV BP 128 102 25 127 27 6 167 24 30 152 180 2,5 kg
04 SC, ISSC LP 134 102 25 127 27 6 153 24 30 154 180 2,5 kg
05 WP, WS, EM, WSEM, WPIS, WSIS LP 134 102 25 127 27 6 167 24 30 168 180 2,5 kg

MOUNTING BRACKETS






Bracket number : 115292-001

Material : Zinc plated steel

80340GB-2017/R01

All leaflets are available on: www.asco.com

5
6
All leaflets are available on: www.asco.com
SERIES 307

PIC-11-0040-GB -- Availability, design and specifications are subject to change without notice. All rights reserved.
80340GB-2017/R01