RFID Card Access control Operating manual
0 0
[I] [g] ~
@][ID[ID
[z] [ID [ID
[b)] [ill [i]
(please read operating maual carefully before use)
[operating manual] Please keep the operating manual carefully
Technical specification
1. Product main tech nical Specification
ec11catIon
-
nta temperature:
requency z
IC Model: 1 .56MHz
or compatI e
atible
IC Model:3-SCM
t or eve out ut
to cetam mo es
2.
conds
D,
Programming
3. Sound and Light show
3.1: Normal working condition
3.1.1. valide command : a short beep sound
3.1.2. Invalid command:a long beep sound
3.2. Programming mode:
3.2.1 Green LED On
3.2.2 valid command: beep beep two sounds
3.2.3 invalid valid: three beeps
4. Cancel command
command have not all been completed, press the[#] key, you can cancel the command
5.functions and settings programming
5.1 Enter the programming mode:
press [#J+[ 6-digit pin]( default: 881, 122)
5.2 mod,~ the programming PIN:
Press [O + [new 6-digit pin] + [confirm the nes 6-digit pin]
5.3 Erol card:
press rs] + [3-digit index code] (2 beeps ) + [card 1] (beep, 2 beeps ) + [card 2] (beep, 2 beeps )+ .... . .
+ rcard n ] (beep, 2 beeps ) + [#] (2 beeps )
5.3.1.3-digit index code : rang from 001--------- 999 number can not be repeated. The code is an
important way deleted the carcf after the card is lost, please save the card coded issuer properly
5.3.2. when enrolling multiple cards, every card index code will be calculated in order. For example,
card one's indes cocfe is 015, once again, card two's will be 016 ...... and so on
5.3.3 the default private pin for each card is : 0000
5.4 Delete Card:
5.4.1 Delete by index Card:
~#ress[7] + [3-digit code 1J (2beeps) + [3-digit code 2] (2beeps )+ .. . + [3-digit code N] (2beeps )+
§ ](2beeps) complete the delete cards . .
.4.2. delete by presenting cards: press[?] + [proximity card 1] (beep, 2beeps ) + [proximity ca rd 2]
-
Programming a
(beep, 2beeps ) + ...... + (proximity card NJ (beep, 2beeps ) + [#] (2beeps ) complete the deletion
g~J~3 delete all car~s: Please restore the factory default
5.4.4 the private pin will be deleted when the card Is deleted
5.5. exit programming mode: press[#] (2beeps )
5.6. set up door open mode
5.6.1. card or pin mode:press (1] + (O] (2beeps ) (default)
5.6.2. Card +private PIN mode: [1] + [1 ] (2beeps)
5.7 pins . . . .
5.7.1. "Card or pin" for the mode is either the public ptn or private pm (up to 999)
5.7.2. disable changing private pin:press [1] + [2] (2beeps) (default)
5.7.3. enable changing private pin: press[1] + (31 (2beeps )
5.7.4 change frivate pin:
f
press[# (beep,2beeps ) + presenting card] (beep,2beeps ) + [4-digH old pin] ( default 0000)
(2beeps ) + [4-digit new pin + fconfirm the new pinl (2beeps )
5.7.5. change public pin:press [3] +J4-digit pin] (default 1234)
When the public or priv~te pin is O 00,tfle pin is void in "card or pin" mode
5.8. c~ang~ door open time: press[2]+[TT]. TT is the time interval in seconds. For example.if the door
open time Is 3 seconds, TT=03
5.9.Anti-break:
5.9.1.Disable anti-break:press [4]+[0]
5.9.2. Enable anti-break: press[4]+[1J
5.10. Door contact sensor·
5.10.1. disable door sensor : pressf6]+f0]
5.10.2. enable door sensor:press [6]+[1]
5.11 . Door sensor alarm·
5.11 .1 Disable alarm: pressf8]+f0]
5.11 .2 enable alarm: pres (8]+[ 1 . . .
s ] After turning on this function ,the cotroller will give off continuous long
l
Programming
beep when the door is not closed after normal opening ,or the door is not opened through the controller.
5.12. Alarm de~ime:
press [82l+ll TJ.
TT is the lime interval in seconds.For example,if the delay time is 3 seconds ,then TT=3
When door is locked TT seconds,if the door contact sensor is in alarm status,the controller is in
alarm mode.This function should be used when the door sensor alarm is on .
6.Restore factory default: press[86] There will be 2 beeps, 3 beeps and 3 beeps after 5 seconds , then
the factory defaults are restored.
7. User's instruction:
7.1. Card or PIN mode:
7 .1.1. The pins should be enered in 2 seconds
7.1.2. press [#] key to cancel pin input
7.2. Card +Private PIN mode
7 .2.1[reading card] +[enter 4-di_gi~ pin ] to open
7.2.2. press t#] key to cancel pm mput
8. Reset programming pin: . ..
Short the J2 on controller to res~t the programming pin to factory default (for details sees wiring
diagram explanation)
9. warning output: When has one of above the following conditions, has the warning to
output .
1. reports to the police the AUX IN electric potential to be low;
2. antiwithdrawl has the warning;
3. a magnetism has the warning .
,.
Programming
10. frequently asked questions
Symptom Possible wrongs and solutions
After the lock is opened.there The controller needs higher voltage; the power supply should be
are 8 short beeps checked
The ca rd reading distance is 1. The controller puts in the metal surface, adjusts the controller
short or card cannot be read position
2. The electric current insufficient supply, adjusting power
source
After reading card ,there are 3 1. It's in card +pin mode
beeps and lock is not open 2. [#]key is pressed wait for 5 seconds to present the card
The enrolled card cannot open Check if the door sensor is in alarm status.
the door Disable the door sensor alarm
Press[#] + [programming pin] Other keys are pressed befor pressing the [#]key, Keep on
there is long beep and cannot pressing [#] key after ong beep. Then enter the programming
enter the programming mode mode again.
Press[#] key, there is a long Other keys are pressed before pressing the [#]key, Keep on
beep and cannot enter the pressing[#] key after ong beep, then press the [#] key again
programming mode
press I51, there are 3 beeps The controller has full card capacity
Press [5] + [index code] This code was already used, must press [5] + (3 codes] to
3beeps operate
Press[5] + [index code] This index code is in use ,select another index code.
2beeps+ [presenting card]
3beeps
under the programming mode In programming mode, if there is no input in 20 seconds.the
has not operated, the controller exits programming mode automatically
controller exit programming
mode
Do •
Controller positive/Wiring diagram
Access Controller positive Access Controller on t he back of Wiring Diagram
0 0
[I] [g] ~
@J[ID[ID Electric Lock
Relay Output~-f.-MH
COM
NC
NO
AUA-COM
NC
Ala rm Relay
Output
NOl~.....+---1.__ ______.
[z] [ID CID
~[Q][j
Power ....
0
0
Q)
,:,
C
BATT Cc
--
1:1 0
Q)
C
.0
....
0
E
~-
(0 ...
Q) :::,
+12V
GND
:::i -
0 ~
0
0 ....
Ill
<(
~~-=
· - (0 ci
PUSH
NC
NO
Force to resto re fac tory program med Password ·
afte r release sho rt J2 legs
Professional Card &Program Developers And Manuf Actures
The rights change and upgrade definition and other product information without advance
notice are preserved by our Company
