Scribd
Upload
59 views2 pages

HB601WG TDS

Uploaded by

Bo Li
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
59 views2 pages

HB601WG TDS

Uploaded by

Bo Li
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

21.12.2022 Ed.

10
PRODUCT DATA SHEET

Polypropylene

HB601WG
Polypropylene Homopolymer

Description
HB601WG is a polypropylene homopolymer intended for injection moulding and blow moulding. The product is available in natural and is suitable for
high-gloss applications.

This material has excellent balanced mechanical properties and is easy to process.

Typical characteristics
HB601WG can be described with following typical characteristics:

High heat stabilised UL listed


Detergent resistant

Applications
HB601WG is intended for following applications:
Aesthetical parts Washing machine parts
Appliances Small appliances
Household applications Heat exchangers
Dishwashers components

Physical properties
Property Typical value * Unit Test method
Density 900 kg/m³ ISO 1183-1/Method A
Flexural modulus 1400 MPa ISO 178
Melt flow rate (230 °C/2.16 kg) 2 g/10min ISO 1133-1
Tensile strength (50 mm/min) 35 MPa ISO 527-2
Heat deflection temperature B (0.45 MPa) 85 °C ISO 75-2
Charpy impact strength, notched (23 °C) 6 kJ/m² ISO 179-1/1eA
* Data should not be used for specification work

Processing techniques
Processing Techniques:

The actual conditions will depend on the type of equipment used.

Injection Moulding:

This product is easy to process with standard injection moulding machines. Following parameters should be used
as guidelines:

1/2
Polypropylene
HB601WG
Processing setting Typical value/range

Feeding temperature 40 - 80 °C

Mass temperature 220 - 260 °C

Back pressure low to medium MPa

Holding pressure 30 - 60 MPa

Mould temperature 30 - 50 °C

Screw speed low to medium m/s

Flow front speed 100 - 200 mm/s

Packaging and storage


HB601WG should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which
can result in odour generation and colour changes and can have negative effects on the physical properties of this product.

Product compliance documents


Latest versions of product safety information sheets (PSIS), product safety data sheets (SDS) and other product liability documents are available in our
website www.borealisgroup.com.

Sustainability aspects
Borealis is ever mindful of the impact of our products on the planet. We promote Design for Circularity (DfC) and Design for Recycling (DfR) to conserve
natural resources and to reduce the environmental impact of products over their entire lifetime (including production, use phase and after phase). DfR
helps ensure that material can be effectively recycled while maximizing the material performance efficiency.

Further information on sustainability and Design for Recycling (DfR) can be found from our websites www.borealisgroup.com and
www.borealiseverminds.com.

Disclaimer
The product(s) mentioned herein are not intended to be used for medical, pharmaceutical or healthcare applications and we do not support their use for such
applications.
To the best of our knowledge, the information contained herein is accurate and reliable as of the date of publication; however we do not assume any liability whatsoever
for the accuracy and completeness of such information.
Borealis makes no warranties which extend beyond the description contained herein. Nothing herein shall constitute any warranty of merchantability or fitness for a
particular purpose.
It is the customer's responsibility to inspect and test our products in order to satisfy itself as to the suitability of the products for the customer's particular purpose. The
customer is responsible for the appropriate, safe and legal use, processing and handling of our products.
No liability can be accepted in respect of the use of any Borealis product in conjunction with any other products and/or materials. The information contained herein relates
exclusively to our products when not used in conjunction with any other material unless as specifically provided for in the test methods stated above.

Borealis AG | Trabrennstrasse 6-8 | A-1020 Vienna | Austria


Telephone: +43 1 22 400 0* | Fax: +43 1 22 400 333
Website www.borealisgroup.com

2/2

You might also like