Stainless Steel Grade 304 / 1.

4301

Stainless steel types1.4301 and 1.4307 Typical Chemical Composition

are also known as grades 304 and
304L respectively. Type 304 is the % 304 304L 304H
most versatile and widely used
C 0.08 max 0.03 max 0.10 max
stainless steel. It is still sometimes
referred to by its old name 18/8 which Mn 2.0 2.0 2.0
is derived from the nominal Si 0.75 0.75 0.75
composition of type 304 being 18%
chromium and 8% nickel. P 0.045 0.045 0.045

Type 304 stainless steel is an S 0.03 0.03 0.03

austenitic grade that can be severely Cr 18-20 18-20 18-20
deep drawn. This property has resulted Ni 10.5 12 10.5
in 304 being the dominant grade used
in applications like sinks and N 0.1 0.1 -
saucepans.
Type 304L is the low carbon version of
304. It is used in heavy gauge Typical Mechanical Properties
components for improved weldability.
Some products such as plate and pipe Grade 304 304L 304H
may be available as “dual certified” Tensile Strength
material that meets the criteria for 520 500 520
(MPa)
both 304 and 304L.
Compression
304H, a high carbon content variant, is Strength 210 210 210
also available for use at high
(MPa)
temperatures.
Proof Stress
Property data given in this document is 210 200 210
0.2% (MPa)
typical for flat rolled products covered
by ASTM A240/A240M. ASTM, EN or Elongation A5
45 45 45
other standards may cover products (%)
sold by Aalco. It is reasonable to Hardness
expect specifications in these 92 92 92
Rockwell B
standards to be similar but not
necessarily identical to those given in
this datasheet.
Typical Physical Properties

Property Value
Applications
Density 8.00 g/cm3
304 stainless steel is typically used in: Melting Point 1400-1450°C
Modulus of Elasticity 193 GPa
‹ Sinks and splashbacks Electrical Resistivity 0.072x10-6 Ω.m
‹ Saucepans
‹ Cutlery and flatware Thermal 16.2 W/m.K at
‹ Architectural panelling Conductivity 100°C
‹ Sanitaryware and troughs 17.2x10-6 /K at
Thermal Expansion
‹ Tubing 100°C
‹ Brewery, dairy, food and pharmaceutical
production equipment
‹ Springs, nuts, bolts and screws
X
Alloy Designations Cold Working

Stainless steel 304 also corresponds to the 304 stainless steel readily work hardens.
following standard designations and Fabrication methods involving cold working
specifications: may require an intermediate annealing
stage to alleviate work hardening and avoid
tearing or cracking. At the completion of
Euronorm UNS BS En Grade fabrication a full annealing operation should
1.4301 S30400 304S15 58E 304 be employed to reduce internal stresses
304S16 and optimise corrosion resistance.
304S31
1.4306 S30403 304S11 - 304L
Hot Working
1.4307 - 304S11 - 304L
1.4311 - 304S11 - 304L Fabrication methods, like forging, that
1.4948 S30409 304S51 - 304H involve hot working should occur after
uniform heating to 1149-1260°C. The
fabricated components should then be
rapidly cooled to ensure maximum
Corrosion Resistance
corrosion resistance.

304 has excellent corrosion resistance in a

wide variety of environments and when in
contact with different corrosive media. Heat Treatment
Pitting and crevice corrosion can occur in
environments containing chlorides. Stress 304 stainless steel cannot be hardened by
corrosion cracking can occur at heat treatment.
temperatures over 60°C. Solution treatment or annealing can be
done by rapid cooling after heating to
1010-1120°C.
Heat Resistance

304 has good resistance to oxidation in Machinability

intermittent service up to 870°C and in
continuous service to 925°C. However, 304 has good machinability. Machining can
continuous use at 425-860°C is not be enhanced by using the following rules:
recommended if corrosion resistance in
water is required. In this instance 304L is
recommended due to its resistance to ‹ Cutting edges must be kept sharp. Dull
carbide precipitation. edges cause excess work hardening.
‹ Cuts should be light but deep enough to
Where high strength is required at prevent work hardening by riding on the
temperatures above 500°C and up to surface of the material.
800°C, grade 304H is recommended. This ‹ Chip breakers should be employed to
material will retain aqueous corrosion assist in ensuring swarf remains clear of
resistance. the work
‹ Low thermal conductivity of austenitic
Fabrication alloys results in heat concentrating at
the cutting edges. This means coolants
Fabrication of all stainless steels should be and lubricants are necessary and must
done only with tools dedicated to stainless be used in large quantities.
steel materials. Tooling and work surfaces
must be thoroughly cleaned before use.
These precautions are necessary to avoid
cross contamination of stainless steel by
easily corroded metals that may discolour
the surface of the fabricated product.
X
Welding Supplied Forms

Fusion welding performance for type 304 304 is typically supplied by Aalco in a range
stainless steel is excellent both with and of finishes in the following forms:
without fillers. Recommended filler rods and
electrodes for stainless steel 304 is grade ‹ Sheet
308 stainless steel. For 304L the ‹ Plate
recommended filler is 308L. Heavy welded ‹ Welded mesh
sections may require post-weld annealing. ‹ Quarto plate
This step is not required for 304L. Grade ‹ Round bar
321 may be used if post-weld heat ‹ Flat bar and rolled edge flat bar
treatment is not possible. ‹ Equal angle
‹ Square bar
‹ Hollow bar
‹ Seamless pipe
‹ Welded pipe
‹ Seamless butt weld fittings
‹ Welded butt weld fittings
‹ Flanges
‹ Seamless tube
‹ Hygienic fittings
‹ Round, square and rectangular
decorative tube

This information is based on our present

knowledge and is given in good faith.
However, no liability will be accepted by the
Company is respect of any action taken by
any third party in reliance thereon
As the products detailed may be used for a
wide variety of purposes and as the
Company has no control over their use; the
Company specifically excludes all conditions
or warranties expressed or implied by
statute or otherwise as to dimensions,
properties and/or fitness for any particular
purpose. Any advice given by the Company
to any third party is given for that party’s
assistance only and without liability on the
part of the Company.
Any contract between the Company and a
customer will be subject to the Company’s
Conditions of Sale. The extent of the
Company’s liabilities to any customer is
clearly set out in those Conditions; a copy
of which is available on request.
 Stainless Steel Grade 316 / 1.4401
Stainless steel types 1.4401 and Typical Chemical Composition
1.4404 are also known as grades 316
and 3164L respectively. Grade 316 is % 316 316L 316H
an austenitic grade second only to 304
C 0.08max 0.03max 0.1max
in commercial importance.
Mn 2.0 2.0 2.0
316 stainless steel contains an addition
of molybdenum that gives it improved Si 0.75 0.75 0.75
corrosion resistance. This is P 0.045 0.045 0.045
particularly apparent for pitting and
crevice corrosion in chloride S 0.03 0.03 0.03
environments. Cr 16-18 16-18 16-18
316L, the low carbon version of 316 Mo 2-3 2-3 2-3
stainless steel, is immune to grain Ni 10-14 10-14 10-14
boundary carbide precipitation
(sensitisation). This makes it suited to N 0.1 0.1 -
use in heavy gauge (over about 6mm)
welded components.
For elevated temperature applications Typical Mechanical Properties
the high carbon variant, 316H stainless
steel and the stabilised grade 316Ti Grade 316 316L 316H
stainless steel should be employed. Tensile Strength
515 485 515
The austenitic structure of 316 (MPa)
stainless steel gives excellent Compression
toughness, even at cryogenic Strength 170 170 170
temperatures.
(MPa)
Property data given in this document is
Proof Stress
typical for flat rolled products covered 205 170 205
0.2% (MPa)
by ASTM A240/A240M. ASTM, EN or
other standards may cover products Elongation A5
40 40 40
sold by Aalco. It is reasonable to (%)
expect specifications in these Hardness
standards to be similar but not 95 95 95
Rockwell B
necessarily identical to those given in
this datasheet.
Typical Physical Properties
Applications
Property Value
Initially developed for use in paper mills Density 8.00 g/cm3
316 stainless steel is now typically used in: Melting Point 1375-1400°C
Modulus of Elasticity 193 GPa
‹ Food processing equipment
Electrical Resistivity 0.074x10-6 Ω.m
‹ Brewery equipment
‹ Chemical and petrochemical equipment Thermal 16.3 W/m.K at
‹ Laboratory benches & equipment Conductivity 100°C
‹ Coastal architectural panelling 15.9x10-6 /K at
‹ Coastal balustrading Thermal Expansion
100°C
‹ Boat fittings
‹ Chemical transportation containers
‹ Heat exchangers
‹ Mining screens
‹ Nuts and bolts
X
‹ Springs
‹ Medical implants
Alloy Designations Cold Working

Stainless steel 316 also corresponds to the Grade 316 is readily brake or roll formed
following standard designations and into a variety of parts. It is also suited to
specifications: stamping, heading and drawing but post
work annealing is recommended to relieve
internal stresses.
Euronorm UNS BS En Grade
Cold working will increase both strength
1.4401 S31600 316S31 58H 316 and hardness of 316 stainless steel.
1.4404 S31603 316S11 - 316L
- S31609 316S51 - 316H
Hot Working
1.4571 - 320S31 - 316Ti
All common hot working processes can be
performed on 316 stainless steel. Hot
Corrosion Resistance working should be avoided below 927°C.
The ideal temperature range for hot
Grade 316 has excellent corrosion working is 1149-1260°C. Post-work
resistance when exposed to a range of annealing is recommended to ensure
corrosive environments and media. It is optimum corrosion resistance.
usually regarded as “marine grade”
stainless steel but is not resistant to warm
sea water. Warm chloride environments can
Heat Treatment
cause pitting and crevice corrosion. Grade
316 is also subject to stress corrosion
cracking above around 60°C. 316 stainless steel cannot be hardened by
heat treatment.
Solution treatment or annealing can be
Heat Resistance done by rapid cooling after heating to
1010-1120°C.
316 has good resistance to oxidation in
intermittent service to 870°C and in
continuous service to 925°C. However, Machinability
continuous use at 425-860°C is not
recommended if corrosion resistance in 316 stainless steel has good machinability.
water is required. In this instance 316L is Machining can be enhanced using the
recommended due to its resistance to following rules:
carbide precipitation.
Where high strength is required at ‹ Cutting edges must be kept sharp. Dull
temperatures above 500°C, grade 316H is edges cause excess work hardening.
recommended. ‹ Cuts should be light but deep enough to
prevent work hardening by riding on the
surface of the material.
Fabrication ‹ Chip breakers should be employed to
assist in ensuring swarf remains clear of
the work
Fabrication of all stainless steels should be
‹ Low thermal conductivity of austenitic
done only with tools dedicated to stainless
alloys results in heat concentrating at
steel materials. Tooling and work surfaces
the cutting edges. This means coolants
must be thoroughly cleaned before use.
and lubricants are necessary and must
These precautions are necessary to avoid
be used in large quantities.
cross contamination of stainless steel by
easily corroded metals that may discolour
the surface of the fabricated product.

X
Welding Supplied Forms

Fusion welding performance for 316 316 stainless steel is typically supplied by
stainless steel is excellent both with and Aalco in a range of finishes in the following
without fillers. Recommended filler rods and forms:
electrodes for 316 and 316L are the same
as the base metal, 316 and 316L ‹ Sheet
respectively. Heavy welded sections may ‹ Plate
require post-weld annealing. Grade 316Ti ‹ Welded mesh
may be used as an alternative to 316 in ‹ Quarto plate
heavy section welds. ‹ Round bar
Oxyacetylene welding has not been found ‹ Flat bar and rolled edge flat bar
to be successful for joining of 316 stainless ‹ Equal angle
steel. ‹ Square bar
‹ Hollow bar
‹ Seamless pipe
‹ Welded pipe
316Ti
‹ Seamless butt weld fittings
‹ Welded butt weld fittings
Another variation of 316 is available. This ‹ Flanges
variation is 316Ti. Stainless steel grade ‹ Seamless tube
316Ti contains a small amount of titanium. ‹ Hygienic fittings
Titanium content is typically only around ‹ Round, square and rectangular
0.5%. The titanium atoms stabilise the decorative tube
structure of the 316 at temperatures over
800°C. This prevents carbide precipitation
at the grain boundaries and protects the
This information is based on our present
metal from corrosion. The main advantage
knowledge and is given in good faith.
of 316Ti is that it can be held at higher
However, no liability will be accepted by the
temperatures for a longer period without
Company is respect of any action taken by
sensitisation (precipitation) occurring. 316Ti
any third party in reliance thereon
retains physical and mechanical properties
similar to standard grades of 316. As the products detailed may be used for a
wide variety of purposes and as the
Company has no control over their use; the
Company specifically excludes all conditions
or warranties expressed or implied by
statute or otherwise as to dimensions,
properties and/or fitness for any particular
purpose. Any advice given by the Company
to any third party is given for that party’s
assistance only and without liability on the
part of the Company.
Any contract between the Company and a
customer will be subject to the Company’s
Conditions of Sale. The extent of the
Company’s liabilities to any customer is
clearly set out in those Conditions; a copy
of which is available on request.
 STAINLESS STEEL PIPES & FITTINGS

A stainless steel pipe system is the product of choice for carrying corrosive or sanitary fluids,
slurries and gases, particularly where high pressures, high temperatures or corrosive
environments are involved. Due to stainless steel’s aesthetic properties, stainless steel pipe is
also used in architectural applications.

Stainless steel pipe can be generally defined as a heavy wall thickness tubing, with dimensions as
specified by the American National Standards Institute (ANSI). Pipe dimensions are specified by outside
diameter – indicated by the NPS (imperial) or DN (metric) designator and sometimes confusingly referred
to as the ‘nominal bore’ – and wall thickness, reflected in the schedule number. ASME B36.19M covers
these dimensions.

Stainless steel pipe and fittings are supplied in the annealed condition to facilitate fabrication and ensure
best corrosion resistance. Atlas Steels can also supply stainless steel pipe with an abrasive polished
external finish suitable for architectural applications.

Welded Pipe
Welded stainless steel pipe is manufactured from 2B or HRAP stainless steel strip – formed to shape,
longitudinally welded and annealed.

Large size pipe is fabricated from plate.

All welds are made without the addition of filler metal, except for very large diameters.

Standard welded pipe is in nominal lengths of 6.0 or 6.1 metres.

Manufacturing specification: ASTM A312M – Austenitic

ASTM A358M – Austenitic (large diameter)
ASTM A790M – Duplex

Seamless Pipe
Seamless stainless steel pipe is produced from hollow billets, which are pierced then usually cold drawn
until they reach the final desired pipe size, then annealed.

Standard seamless pipe is supplied in nominal lengths of 6.1 metres to DN 150 (NPS 6) and above this in
random lengths.

Manufacturing specification: ASTM A312M – Austenitic

ASTM A790M – Duplex

Stainless steel piping systems can be joined by butt welding and, in the heavier 40S and 80S
schedules, by threaded connections.

The complete piping system is made possible using complementary fittings and flanges. These are
specified by the same DN or NPS designator and schedule numbering system as for pipe.
 STAINLESS STEEL PIPES & FITTINGS

Butt Welding Pipe Fittings

A piping system using butt welding fittings has many inherent advantages over other forms.

 Welding a fitting to the pipe means that it is permanently leak proof

 The continuous metal structure formed between pipe and fitting adds strength to the system

 Smooth inner surface and gradual direction changes reduce pressure losses and turbulence and
minimise the action of corrosion and erosion

 A welded system utilizes a minimum of space

Atlas Steels Supply Butt Welding Fittings in the following forms

 Elbows 45o and 90o – long radius is standard; short radius is also available

 Return bends 180o – long radius is standard; short radius is also available

 Reducers – concentric and eccentric

 Tees – equal and reducing

 Caps

 Stub ends – Type B, to MSS SP-43

Butt welding fittings can be supplied in either seamless or welded construction and are covered by
specification ASTM A403M (or ASTM A815M for Duplex grades) and ASME B16.9.

Screwed and Socket Weld Fittings

Piping systems can be connected using screwed fittings – BSP threaded (“150lb”) low pressure fittings
and NPT threaded (class 3000) high pressure fittings in Grade 316.

Socket weld fittings are used in high pressure piping systems and are available in grade 316L to suit
schedule 80S wall thickness piping.

Manufacturing specification: ASTM A182M (Class 3000 NPT and socket weld) and
ASME B16.11
ISO 4144 (BSP dimensions)
 STAINLESS STEEL PIPES & FITTINGS

Stainless Steel Pipe – Welded & Seamless – ASTM A312M / ASTM A790M
Grades: 304/304L, 316/316L, 2205

Stainless steel pipe is available in a wide range of sizes in welded and seamless construction, ex-stock or
on indent.

Nominal Wall Thickness (mm)

Outside
Pipe Size Sch 5S Sch 10S Sch 40S Sch 80S
Diameter
(mm) WT Weight WT Weight WT Weight WT Weight
DN NPS
(mm) (kg/m) (mm) (kg/m) (mm) (kg/m) (mm) (kg/m)
6 ⅛ 10.3 1.24 0.28 1.73 0.37 2.41 0.47
8 ¼ 13.7 1.65 0.49 2.24 0.63 3.02 0.80
10 ⅜ 17.1 1.65 0.63 2.31 0.84 3.20 1.10
15 ½ 21.3 1.65 0.80 2.11 1.00 2.77 1.27 3.73 1.62
20 ¾ 26.7 1.65 1.02 2.11 1.28 2.87 1.69 3.91 2.20
25 1 33.4 1.65 1.29 2.77 2.09 3.38 2.50 4.55 3.24
32 1¼ 42.2 1.65 1.65 2.77 2.69 3.56 3.39 4.85 4.47
40 1½ 48.3 1.65 1.90 2.77 3.11 3.68 4.05 5.08 5.41
50 2 60.3 1.65 2.39 2.77 3.93 3.91 5.44 5.54 7.48
65 2½ 73.0 2.11 3.69 3.05 5.26 5.16 8.63 7.01 11.41
80 3 88.9 2.11 4.52 3.05 6.46 5.49 11.29 7.62 15.27
90 3½ 101.6 2.11 5.18 3.05 7.41 5.74 13.57 8.08 18.64
100 4 114.3 2.11 5.84 3.05 8.37 6.02 16.08 8.56 22.32
125 5 141.3 2.77 9.46 3.40 11.56 6.55 21.77 9.53 30.97
150 6 168.3 2.77 11.31 3.40 13.83 7.11 28.26 10.97 42.56
200 8 219.1 2.77 14.78 3.76 19.97 8.18 42.55 12.70 64.64
250 10 273.1 3.40 22.61 4.19 27.79 9.27 60.31 12.70 81.56
300 12 323.9 3.96 31.25 4.57 35.99 9.53 73.88 12.70 97.47
350 14 355.6 3.96 34.34 4.78 41.36 9.53 81.33 12.70 107.40
400 16 406.4 4.19 41.56 4.78 47.34 9.53 93.27 12.70 123.31
450 18 457 4.19 46.79 4.78 53.31 9.53 105.17 12.70 139.16
500 20 508 4.78 59.32 5.54 68.65 9.53 117.15 12.70 155.13
550 22 559 4.78 65.33 5.54 75.62
600 24 610 5.54 82.58 6.35 94.53 9.53 141.12 12.70 187.07
650 26 660
700 28 711
750 30 762 6.35 118.34 7.92 147.29

 Stainless steel pipe nominal dimensions listed in the table are based on ASTM A312M and ASME B36.19M.
 These dimensions are nominal – substantial tolerances apply – refer to Atlas Steels TechNote 12 and the ASTM
and ASME standards for details.
 For other wall thicknesses and larger sizes consult ASME B36.10M; stainless steel pipe may be available to
these carbon steel pipe sizes.
 STAINLESS STEEL PIPES & FITTINGS

Welded Butt Welding Fittings – ASTM A403M & ASME B16.9

Product range and theoretical weights (kg)

Schedule 10S Schedule 40S
DN Stub Stub
900 450 Equal 900 450 Equal
end type End cap end type End cap
Elbow Elbow tee Elbow Elbow tee
B B

15 0.06 0.03 0.09 0.07 0.03 0.08 0.04 0.10 0.08 0.04
20 0.07 0.03 0.13 0.09 0.05 0.08 0.04 0.17 0.11 0.07
25 0.14 0.08 0.28 0.16 0.08 0.15 0.11 0.29 0.17 0.10
32 0.23 0.11 0.49 0.22 0.10 0.26 0.17 0.59 0.25 0.18
40 0.30 0.17 0.68 0.25 0.11 0.40 0.23 0.86 0.31 0.20
50 0.50 0.25 0.85 0.43 0.13 0.70 0.40 1.28 0.61 0.23
65 0.85 0.48 1.41 0.57 0.19 1.40 0.77 2.19 0.80 0.27
80 1.25 0.63 1.77 0.72 0.25 2.20 1.08 3.31 1.13 0.42
100 2.10 1.08 3.46 1.09 0.68 4.47 1.47 5.27 1.87 1.14
125 3.65 1.82 5.44 1.47 1.11 6.80 2.84 9.63 2.79 2.13
150 5.45 2.72 8.03 2.15 1.42 10.89 5.44 10.99 3.57 3.23
200 10.20 5.33 15.65 3.22 2.38 21.54 10.77 20.91 6.07 5.19
250 18.15 9.75 26.76 5.13 4.45 38.56 19.27 35.38 10.07 9.00
300 25.80 13.62 39.46 8.16 7.50 59.42 29.71 62.14 14.29 15.00
350 36.29 18.37 48.53 10.88 8.17 79.38 35.15 79.31 17.14 16.00
400 47.63 23.81 58.97 12.70 10.67 99.79 45.81 99.79 20.41 21.00
450 59.87 29.94 79.65 17.23 13.00 129.73 59.40 129.73 27.21 26.00
500 99.80 49.90 103.42 21.77 17.00 162.38 74.84 162.39 29.94 34.00
600 140.61 70.31 155.58 27.21 26.00 225.89 105.23 225.90 38.55 52.00

Grades: Butt welding fittings are usually supplied as dual certified 304/304L or 316/316L
 STAINLESS STEEL PIPES & FITTINGS

Welded Butt Welding Fittings – ASTM A403M & ASME B16.9

Product range and theoretical weights (kg)

Schedule 10S Schedule 40S
DN Con Ecc Reducing Con Ecc Reducing
reducer reducer tee reducer reducer tee
20x15 0.10 0.10 0.11 0.14 0.14 0.15
25x15 0.12 0.12 0.25 0.15 0.15 0.26
25x20 0.13 0.13 0.25 0.16 0.16 0.27
32x20 0.18 0.18 0.44 0.22 0.22 0.52
32x25 0.18 0.18 0.45 0.22 0.22 0.53
40x20 0.18 0.18 0.58 0.24 0.24 0.74
40x25 0.19 0.19 0.60 0.26 0.26 0.76
40x32 0.21 0.24 0.61 0.28 0.28 0.77
50x25 0.28 0.28 0.73 0.40 0.40 1.10
50x32 0.30 0.30 0.74 0.44 0.44 1.13
50x40 0.31 0.31 0.76 0.45 0.45 1.15
65x40 0.44 0.44 1.24 0.76 0.76 1.94
65x50 0.47 0.47 1.25 0.80 0.80 1.98
80x40 0.51 0.51 1.52 0.94 0.94 2.85
80x50 0.55 0.55 1.56 1.00 1.00 2.91
80x65 0.59 0.59 1.59 1.08 1.08 2.98
100x40 0.68 0.68 2.90 1.36 1.36 4.53
100x50 0.78 0.78 2.94 1.57 1.57 4.48
100x65 0.83 0.83 2.97 1.66 1.66 4.54
100x80 0.87 0.87 3.04 1.74 1.74 4.64
125x100 1.49 1.49 5.49 2.98 2.98 8.47
150x80 1.82 1.82 6.86 3.98 3.98 11.94
150x100 1.96 1.96 7.10 4.07 4.07 9.68
150x125 2.00 2.00 7.27 4.07 4.07 9.99
200x100 3.01 3.01 13.46 6.55 6.55 17.98
200x150 3.19 3.19 14.08 6.94 6.94 18.82
250x100 4.73 4.73 22.75 10.52 10.52 30.07
250x150 5.00 5.00 23.55 11.12 11.12 31.13
250x200 5.20 5.20 24.08 11.56 11.56 31.84
300x200 7.67 7.67 34.73 15.98 15.98 54.43
300x250 7.98 7.98 35.52 16.63 16.63 55.79
350x300 15.29 15.29 43.96 30.58 30.58 71.21
400x200 16.70 16.70 49.90 33.40 33.40 84.82
400x250 17.22 17.22 50.80 35.43 35.43 85.73
400x300 18.35 18.35 51.71 36.70 36.70 87.54

Grades: Butt Welding Fittings are usually supplied as dual certified 304/304L or 316/316L
 STAINLESS STEEL PIPES & FITTINGS

Seamless Butt Welding Fittings – ASTM A403M & ASME B16.9

Product range and theoretical weights (kg)

Schedule 10S Schedule 40S Schedule 80S
DN
0 0 0 0 0
90 Elbow 45 Elbow Equal tee 90 Elbow 45 Elbow Equal tee 90 Elbow 450 Elbow Equal tee

8 0.02 0.01 0.03 0.03 0.02 0.06 0.04 0.03 0.07

10 0.03 0.02 0.05 0.03 0.02 0.03 0.06 0.04 0.09
15 0.06 0.03 0.09 0.08 0.04 0.10 0.10 0.05 0.14
20 0.07 0.03 0.13 0.08 0.04 0.17 0.11 0.05 0.20
25 0.14 0.08 0.28 0.15 0.11 0.29 0.22 0.14 0.38
32 0.23 0.11 0.49 0.26 0.17 0.59 0.40 0.23 0.68
40 0.30 0.17 0.68 0.40 0.23 0.86 0.51 0.29 1.02
50 0.50 0.25 0.85 0.70 0.4 1.28 0.91 0.59 1.59
65 0.85 0.48 1.41 1.40 0.77 2.19 1.81 0.99 3.13
80 1.25 0.63 1.77 2.20 1.08 3.31 2.97 1.50 4.45
90 1.70 0.75 2.67 2.83 1.42 4.08 4.00 2.00 5.44
100 2.10 1.08 3.46 4.47 2.09 5.27 6.18 2.81 7.71
150 5.45 2.72 8.07 10.89 5.44 10.99 16.32 8.16 13.61
200 10.20 5.33 15.65 21.54 10.77 20.91 33.11 16.56 28.12
250 18.15 9.75 26.46 38.56 19.27 35.38 51.71 25.86 49.90
300 25.80 13.62 39.46 59.42 29.71 62.14 79.38 39.69 83.91

Seamless Butt Welding Fittings – ASTM A403 & ASME B16.9

Product range and theoretical weights (kg)

Schedule 10S Schedule 40S Schedule 80S
DN Con Ecc Reducing Con Ecc Reducing Con Ecc Reducing
reducer reducer tee reducer reducer tee reducer reducer tee

40x.25 0.19 0.19 0.60 0.26 0.26 0.76 0.34 0.34 0.90
50x25 0.28 0.28 0.73 0.40 0.40 1.10 0.54 0.54 1.37
50x40 0.31 0.31 0.76 0.45 0.45 1.15 0.59 0.59 1.43
80x.50 0.55 0.55 1.56 1.00 1.00 2.91 1.79 1.79 3.91
100x50 0.78 0.78 2.94 1.50 1.50 4.48 1.95 1.95 6.55
100x80 0.87 0.87 3.04 1.74 1.74 4.64 2.33 2.33 6.79
150x80 1.82 1.82 6.86 3.95 3.95 9.68 5.51 5.51 11.57
150x100 1.96 1.96 7.10 4.07 4.07 11.94 5.96 5.96 11.97
200x100 3.01 3.01 13.46 6.55 6.55 17.98 9.23 9.23 24.18
200x150 3.19 3.19 14.08 6.74 6.74 18.82 10.12 10.12 25.31

 Austenitic grades specified to ASTM A403M

 Duplex grades specified to ASTM A815M
 Buttwelding fittings are usually supplied as dual certified 304/304L or 316/316L
 Duplex grades 2205 and 2507 are also available in certain sizes.
 STAINLESS STEEL PIPES & FITTINGS

Stainless Steel Butt Welding Fittings – Dimensions

Butt Welding Fittings to ASME B16.9

Elbows Returns Stub Ends
Reducers
Nominal size OD Long Short Caps Radius Diam
Note 1
90 45 90 Long Short Long Short of of
deg deg deg Fillet Lap

DN NPS D A B A O K O K E H F F R G
15 ½ 21.3 38 16 76 48 25 76 51 3 35
20 ¾ 26.7 38 19 76 51 25 38 76 51 3 43
25 1 33.4 38 22 25 76 56 51 41 38 51 102 51 3 51
32 11/4 42.2 48 25 32 95 70 64 52 38 51 102 51 5 64
40 11/2 48.3 57 29 38 114 83 76 62 38 64 102 51 6 73
50 2 60.3 76 35 51 152 106 102 81 38 76 152 64 8 92
65 21/2 73.0 95 44 64 190 132 127 100 38 89 152 64 8 106
80 3 88.9 114 51 76 229 159 152 121 51 89 152 64 10 127
90 31/2 101.6 133 57 89 267 184 178 140 64 102 152 76 10 140
100 4 114.3 152 64 102 305 210 203 159 64 102 152 76 11 157
125 5 141.3 190 79 127 381 262 254 197 76 127 203 76 11 185
150 6 168.3 229 95 152 457 313 305 237 89 140 203 89 13 218
200 8 219.1 305 127 203 610 414 406 313 102 152 203 102 13 270
250 10 273.0 381 159 254 762 518 508 391 127 178 254 127 13 324
300 12 323.8 457 190 305 914 619 610 467 152 203 254 152 13 381
350 14 355.6 533 222 356 1067 711 711 533 165 330 305 152 13 413
400 16 406.4 610 254 406 1219 813 813 610 178 356 305 152 13 470
450 18 457 686 286 457 1372 914 914 686 203 381 305 152 13 533
500 20 508 762 318 508 1524 1016 1016 762 229 508 305 152 13 584
550 22 559 838 343 559 1676 1118 1118 838 254 508 305 152 13 641
600 24 610 914 381 610 1829 1219 1219 914 267 508 305 152 13 692
650 26 660 991 405 267 610
700 28 711 1067 438 267 610
750 30 762 1143 470 267 610
800 32 813 1219 502 267 610
850 34 864 1295 533 267 610
900 36 914 1372 565 267 610
950 38 965 1448 600 305 610
1000 40 1016 1524 632 305 610
1050 42 1067 1600 660 305 610
1100 44 1118 1676 695 343 610
1150 46 1168 1753 727 343 711
1200 48 1219 1829 759 343 711
Note 1: Reducer dimension “H” is based on large end nominal size.
 STAINLESS STEEL PIPES & FITTINGS

Stainless Steel Butt Welding Fittings – Dimensions

 STAINLESS STEEL PIPES & FITTINGS

Screwed Low Pressure “150lb” BSP 316 Fittings

Product range and theoretical weights (kg)

Male/
Pipe Pipe Hex/ Female Hex Square
Round Hex 3 pce fem Female Hex
DN nipple nipple round 90o head head
socket nipple union 90o tee locknut
TBE TOE cap elbow plug plug
elbow
6 0.02 0.02 0.01 0.02 0.02 0.13 0.03 0.02 0.05 0.02 0.02 0.01
8 0.04 0.03 0.02 0.03 0.03 0.11 0.04 0.04 0.05 0.03 0.02 0.02
10 0.05 0.04 0.03 0.03 0.05 0.18 0.06 0.06 0.09 0.03 0.03 0.03
15 0.09 0.08 0.05 0.07 0.08 0.22 0.10 0.11 0.14 0.05 0.04 0.03
20 0.13 0.11 0.08 0.10 0.11 0.33 0.14 0.16 0.21 0.09 0.05 0.07
25 0.20 0.16 0.11 0.17 0.17 0.50 0.27 0.26 0.36 0.12 0.10 0.10
32 0.29 0.29 0.19 0.24 0.25 0.70 0.38 0.40 0.50 0.19 0.14 0.15
40 0.34 0.35 0.23 0.38 0.37 0.87 0.51 0.50 0.70 0.27 0.15 0.21
50 0.52 0.58 0.30 0.47 0.53 1.39 0.75 0.82 1.01 0.40 0.25 031
65 0.78 0.92 0.57 0.85 1.14 2.07 1.69 1.68 2.41 0.76 0.51 0.59
80 1.05 1.45 0.86 1.24 1.37 2.98 2.33 2.06 3.32 1.03 0.55 0.71
100 1.90 2.07 1.38 2.09 1.90 4.82 3.43 3.45 4.81 1.66 0.92 1.10

TBE = Threaded Both Ends

TOE = Threaded One End
 STAINLESS STEEL PIPES & FITTINGS

Screwed Low Pressure “150 lb” BSP 316 Fittings

Product range and theoretical weights (kg)

Hex reducing Hex reducing
DN
bush nipple
8x6 0.01 0.03
10x6 0.02 0.05
10x8 0.03 0.05
15x6 0.04 0.08
15x8 0.06 0.08
BSP Fittings 15x10 0.06 0.08
Dimensions: generally to ISO4144.
20x8 0.08 0.12
Threading: BS21 (ISO 7-1).
Feed materials – sockets, TOE nipples, TBE nipples 20x10 0.07 0.12
manufactured from stainless steel pipe to ASTM A312M.
- Other fittings made from investment castings. 20x15 0.05 0.12
25x10 0.14 0.17
25x15 0.12 0.17
25x20 0.08 0.17
32x25 0.15 0.26
40x20 0.33 0.36
40x25 0.26 0.36
40x32 0.17 0.36
50x25 0.56 0.50
50x32 0.45 0.50
50x40 0.37 0.50
65x50 0.51 0.85
80x50 0.94 1.28
80x55 1.23 1.28
 STAINLESS STEEL PIPES & FITTINGS

Screwed Class 3000 NPT Fittings – ASTM A182M and ASME B16.11

Grade 316

Product range and theoretical weights (kg)

Schedule 40S Schedule 80S
Hex 45o 90o Hex Hex Female
DN Coupling Union Nipple Nipple Nipple Nipple
cap Elbow Elbow nipple plug tee
TBE TOE TBE TOE
8 0.05 0.06 0.13 0.14 0.03 0.03 0.21 0.20 0.06 0.05 0.08 0.06
10 0.06 0.07 0.25 0.27 0.06 0.06 0.27 0.31 0.08 0.06 0.11 0.09
15 0.13 0.14 0.36 0.37 0.08 0.08 0.46 0.49 0.13 0.09 0.16 0.10
20 0.21 0.20 0.53 0.60 0.15 0.15 0.61 0.80 0.17 0.12 0.22 0.16
25 0.37 0.30 0.78 1.08 0.24 0.24 0.99 1.31 0.24 0.18 0.31 0.23
32 0.60 0.73 1.02 1.22 0.37 0.37 1.55 1.61 0.33 0.24 0.44 0.35
40 0.73 1.03 1.70 2.45 0.45 0.45 1.90 3.20 0.40 0.30 0.53 0.40
50 1.10 1.35 2.35 2.50 0.76 0.76 2.86 3.55 0.53 0.40 0.74 0.56

TBE = Threaded Both Ends

TOE = Threaded One End

Grade 304

Product range and theoretical weights (kg)

90o Hex Hex
DN Coupling Union
Elbow nipple plug
15 0.11 0.41 0.08 0.07 0.30
20 0.20 0.68 0.17 0.13 0.58
25 0.29 1.02 0.38 0.20 0.76
32 0.73 1.22 0.37 0.41 1.55
40 1.00 2.44 0.63 0.60 1.60
50 1.42 2.52 1.10 1.10 2.42 Class 6000 and 9000
Higher pressure fittings are available subject to
enquiry
 STAINLESS STEEL PIPES & FITTINGS

Screwed Class 3000 NPT 316 Fittings – ASTM A182M and ASME B16.11

Product range and theoretical weights (kg)

Swage
Hex Hex
nipple Reducing
DN reducing reducing
TBE insert
bush nipple
80S
8x6 0.02 0.05 0.04 0.04
10x6 0.02 0.06 0.06 0.05
10x8 0.03 0.06 0.06 0.05
15x6 0.04 0.08 0.14 0.10
15x8 0.06 0.08 0.14 0.10
15x10 0.06 0.08 0.18 0.010
20x8 0.08 1.15 0.18 0.12
20x10 0.07 0.17 0.18 0.12
20x15 0.05 0.17 0.18 0.12
25x8 0.12 0.38 0.25 0.16
25x10 0.14 0.38 0.25 0.16
25x15 0.12 0.38 0.25 0.16
25x20 0.12 0.38 0.25 0.16
40x15 0.21 0.63 0.60 0.45
40x20 0.21 0.63 0.60 0.45
40x25 0.21 0.63 0.60 0.45
40x32 0.21 0.64 0.60 0.45
50x25 0.45 0.68 1.14 0.70
50x40 0.50 0.70 1.14 0.70
TBE = Threaded Both Ends

Class 6000 and 9000

Higher pressure fittings are available subject to enquiry
 STAINLESS STEEL PIPES & FITTINGS

Socket Weld Class 3000 Fittings – ASTM A182M and ASME B16.11

Grade 316L

Product range and theoretical weights (kg)

DN Cap Coupling 45o Elbow 90o Elbow Equal tee Union
8 0.06 0.07 0.25 0.26 0.30 0.21
15 0.12 0.14 0.36 0.36 0.50 0.30
20 0.21 0.20 0.53 0.60 0.80 0.50
25 0.40 0.40 0.80 1.10 1.31 0.80
32 0.60 0.70 1.00 1.20 1.61 1.20
40 0.70 1.00 1.70 2.40 3.20 1.50
50 1.10 1.30 2.30 2.50 3.50 2.30

Grade 316L Reducing Inserts

Product range and theoretical weights (kg)

Reducing Reducing
DN DN
inserts inserts
20x15 0.12 40x25 0.45
25x15 0.16 50x25 0.7
25x20 0.16 50x40 0.7
40x20 0.45

Class 6000 and 9000 higher pressure rated fittings are available subject to enquiry.
 STAINLESS STEEL PIPES & FITTINGS

Socket Weld Class 3000 Fittings – ASTM A182M and ASME

B16.11 Grade 304L

Product range and theoretical weights (kg)

DN Cap Coupling 45o Elbow 90o Elbow Equal tee Union
8 0.06 0.07 0.25 0.26 0.30 0.21
15 0.12 0.14 0.36 0.36 0.50 0.30
20 0.21 0.20 0.53 0.60 0.80 0.50
25 0.40 0.40 0.80 1.10 1.31 0.80
32 0.60 0.70 1.00 1.20 1.61 1.20
40 0.70 1.00 1.70 2.40 3.20 1.50
50 1.10 1.30 2.30 2.50 3.50 2.30

Branch Outlet Class 3000 304L and 316L – ASTM A182M and ASME B16.11

Product range and theoretical weights (kg)

Socket outlet Threaded Welding Socket outlet Threaded Welding
DN
304L outlet 304L outlet 304L 316L outlet 316L outlet 316L
15 0.15 0.12 0.13 0.15 0.12 0.13
20 0.17 0.24 0.24 0.17 0.24 0.24
25 0.27 0.38 0.38 0.27 0.38 038
40 0.48 0.66 0.66 0.48 0.66 0.66
50 0.07 1.02 1.02 0.75 1.02 1.02

Class 6000 and 9000

Higher pressure fittings are available subject to enquiry
 STAINLESS STEEL PIPES & FITTINGS

3 000 lbs 6 000 lbs

Dimensions Dimensions NIPOLET®

Inches®
C E C E
Outlet size
1/2 90 23,8 90 14,3
3/4 90 30,2 90 19,0
1/2 90 36,5 90 25,0
1 1/4 90 44,5 90 33,0
1 1/2 90 50,8 90 38,0
2 90 65,0 90 43,0

Reduction of varietes through intelligentconstruction

A Weldolet size is suitable for various run pipe sizes (applicable also for Thredolet®, Nipolet®, Elbolet®, Latrolet® and Sockolet®)

Table valid for Weldolet® (Standard and Extra Strong), Thredolet® (3 000 lbs) and Sockolet® (3 000 lbs), Nipolet(3000)

Inches®
suitable for run pipe
Outlet size
1/8 3/8 1/2 1-3/4 2 1/2-1 1/4 36-3
1/4 3/8 1/2 1-3/4 2 1/2-1 1/4 36-3
3/8 1/2 1-3/4 2 1/2-1 1/4 36-3
1/2 1/2 3/4 1 1 1/2-1 1/4 2 1/2-2 8-3 36-10
3/4 3/4 1 1 1/2-1 1/4 2 1/2-2 5-3 12-6 36-14
1 1 1 1/4 1 1/2 2 2 1/2 3 1/2-3 5-4 10-6 36-12
1 1/4 1 1/4 1 1/2 2 2 1/2 3 1/2-3 5-4 8-6 18-10 36-20
1 1/2 1 1/2 2 2 1/2 3 4-3 1/2 6-5 12-8 24-14 36-26
2 2 2 1/2 3 3 1/2 4 5 6 10-8 18-12 36-20
2 1/2 2 1/2 3 3 1/2 4 5 6 8 12-10 18-14 36-20
3 3 3 1/2 4 5 6 8 10 14-12 20-16 36-24
3 1/2 3 1/2 4 5 6 8 10 14-12 20-16 36-24
4 4 5 6 8 10 14-12 20-16 36-24

Table valid for Thredolet® (6 000 lbs) and Sockolet® (6 000 lbs) Table valid for Weldolet® (Schedule 160 & XXS)

Inches® suitable for run pipe suitable for run pipe

1/2 1-3/4 2-1 1/4 6-2 1/2 36-8 1/2 1 1/4-3/4 36-1 1/2
3/4 1 2 1/2-1 1/4 10-3 36-12 1-3/4 2-1 1/4 6-2 1/2 36-8
1 1 1/2-1 1/4 2 1/2-2 10-3 36-12 2 1/2-1 1/4 10-3 36-12
1 1/4 1 1/2 2 1/2-2 3 1/2-3 8-4 20-10 36-24 1 1/2-1 1/4 2 1/2-2 10-3 36-12
1 1/2 2 2 1/2 3 1/2-3 5-4 8-6 18-10 36-20 1 1/2 2 1/2-2 3 1/2-3 8-4 20-10 36-24
2 2 1/2 3 4 5 6 10-8 20-12 36-24 2 2 1/2 3 1/2-3 5-4 8-6 18-10 36-20
Stainless Steel Flanges

EN
STAINLESS STEEL FLANGES
EN1092-1 PN 6
 STAINLESS STEEL FLANGES
EN1092-1 PN 6

Mating dimensions Bore

Flanges thickness
Bolting Outside diameter
Diameter Diameter Cham- Collar
Outside diameter
of bolt of fer thickness
diameter of neck C2
circle bolt hole Number Size B1 B2 C1 C4 E F
D A C3
k k
DN
Flange type
11
11 01
"01 12
01, 02 , 05, 11, 12, 13, 21 21 12 2 05 02 32 35 36 37
02" 13
35-37 32
21
10 75 50 11 4 M10 17.2 18.0 21 12 12 12 3 10 5 2 2.5
15 80 55 11 4 M10 21.3 22.0 25 12 12 12 3 10 5 2 2.5
20 90 65 11 4 M10 26.9 27.5 31 14 14 14 4 10 6 2.5 3
25 100 75 11 4 M10 33.7 34.5 38 14 14 14 4 10 7 2.5 3
32 120 90 14 4 M12 42.4 43.5 46 16 14 14 5 10 8 3 3
40 130 100 14 4 M12 48.3 49.5 53 16 14 14 5 10 8 3 3
50 140 110 14 4 M12 60.3 61.5 65 16 14 14 5 12 8 3 3
65 160 130 14 4 M12 76.1 77.5 81 16 14 14 6 12 8 3 3
80 190 150 18 4 M16 88.9 90.5 94 18 16 16 6 12 10 3 4
100 210 170 18 4 M16 114.3 116.0 120 18 16 16 6 14 10 4 4
125 240 200 18 8 M16 139.7 141.5 145 20 18 18 6 14 10 4 4
150 265 225 18 8 M16 168.3 170.5 174 20 18 18 6 14 10 5 4
200 320 380 18 8 M16 219.1 221.5 226 22 20 20 6 16 11 5 5
250 375 335 18 12 M16 273.0 276.5 281 24 22 22 8 18 12 8
300 440 395 22 12 M20 323.9 327.5 333 24 22 22 8 18 12 8
350 490 445 22 12 M20 355.6 359.5 365 26 22 22 8 18 13 8
400 540 495 22 16 M20 406.4 411.0 416 28 22 22 8 20 14 8
450 595 550 22 16 M20 457.0 462.0 467 30 22 24 8 20 15 8
500 645 600 22 20 M20 508.0 513.5 519 30 24 24 8 22 16 8
600 755 705 26 20 M24 610.0 616.5 622 32 30 30 8 22 16
700 860 810 26 24 M24 711.0 721 40 30 40 4 16
800 975 920 30 24 M27 813.0 824 44 30 44 4 16
specified by purchaser

900 1075 1020 30 24 M27 914.0 926 48 34 48 4 16

1000 1175 1120 30 28 M27 1016.0 1028 52 38 52 4 18
1200 1405 1340 33 32 M30 1219.0 1234 60 42 60 5 20
1400 1630 1560 36 36 M33 1422.0 72 56 68
1600 1830 1760 36 40 M33 1626.0 80 63 76
1800 2045 1970 39 44 M36 1829.0 88 69 84
2000 2265 2180 42 48 M39 2032.0 96 74 92
2200 2475 2390 42 52 M39 2235.0 81
2400 2685 2600 42 56 M39 2438.0 87
2600 2905 2810 48 60 M45 2620.0 91
2800 3115 3020 48 64 M45 2820.0 101
3000 3315 3220 48 68 M45 3020.0 102
3200 3525 3430 48 72 M45 3220.0 106
3400 3735 3640 48 76 M45 3420.0 110
3600 3970 3860 56 80 M52 3620.0 124
 STAINLESS STEEL FLANGES
EN1092-1 PN 6

Diam-
eter Wall
of Length Neck diameter Corner
thick-
shoulder radii
ness
Gmax R1
S
DN H1 H2 H3 H4 H5 N1 N2 N3
Flange type
11
11, 35
12 12 12
05 11 11 35 36 37 11 21 to
13 13 13
37
21
10 20 28 6 28 35 7 26 25 20 4
15 20 30 6 30 38 7 30 30 26 4
20 24 32 6 32 40 8 38 40 34 4
25 24 35 6 35 40 10 42 50 44 4
32 26 35 6 35 42 12 55 60 54 6
40 26 38 7 38 45 15 62 70 64 6
50 28 38 8 38 45 20 74 80 74 6
65 55 32 38 9 38 45 20 88 100 94 6
80 70 34 42 10 42 50 25 102 110 110 8
100 90 40 45 10 45 52 25 130 130 130 8
125 115 44 48 10 48 55 25 155 160 160 8
150 140 44 48 12 48 55 25 184 185 182 10
200 190 44 55 15 55 62 30 236 240 238 10
250 235 44 60 15 60 68 290 295 284 12

Please see wall thickness table

300 285 44 62 15 62 68 342 355 342 12
350 330 62 15 62 68 385 392 12
400 380 65 15 65 72 438 442 12
450 425 65 15 72 72 492 494 12
500 475 68 15 75 75 538 544 12
600 575 70 16 70 640 642 12
700 670 76 16 70 740 746 12
800 770 76 16 70 842 850 12
900 860 78 16 70 942 950 12
1000 960 82 16 70 1045 1050 16
1200 1160 104 20 90 1248 1264 16
1400 1346 114 20 1452 1480 16
1600 1546 119 20 1655 1680 16
1800 1746 133 20 1855 1878 16
2000 1950 146 25 2058 2082 16
2200 154 25 2260 18
2400 168 25 2462 18
2600 175 25 2665 18
2800 188 30 2865 18
3000 192 30 3068 18
3200 202 30 3272 20
3400 214 35 3475 20
3600 229 35 3678 20
STAINLESS STEEL FLANGES
EN1092-1 PN 10
 STAINLESS STEEL FLANGES
EN1092-1 PN 10

Mating dimensions Outside Bore

diam- Flanges thickness
Outside Diameter Diameter Bolting diameter Chamfer
diam- of bolt of eter
Num- E
eter circle bolt hole Size of neck B1 B2 B3 C1 C2 C3 C4
D k k ber A
DN
Flange type
11
01 01 11
21 02
01, 02 , 05, 11, 12, 13, 21 12 02 04 02 12 21 05
34 04
32 04 13
35-37
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 2
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 2
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5
50 165 125 18 4 M16 60.3 61.5 65 77 20 18 18 18 5
65 185 145 18 8 M16 76.1 77.5 81 96 20 18 18 18 6
80 200 160 18 8 M16 88.9 90.5 94 108 20 20 20 20 6
100 220 180 18 8 M16 114.3 116.0 120 134 22 20 20 20 6
125 250 210 18 8 M16 139.7 141.5 145 162 22 22 22 22 6
150 285 240 22 8 M20 168.3 170.5 174 188 24 22 22 22 6
200 340 295 22 8 M20 219.1 221.5 226 240 24 24 24 24 6
250 395 350 22 12 M20 273.0 276.5 281 294 26 26 26 26 8
300 445 400 22 12 M20 323.9 327.5 333 348 26 26 26 26 8
350 505 460 22 16 M20 355.6 359.5 365 400 30 26 26 26 8
400 565 515 26 16 M24 406.4 411.0 416 450 32 26 26 26 8
450 615 565 26 20 M24 457.0 462.0 467 498 36 28 28 28 8
500 670 620 26 20 M24 508.0 513.5 519 550 38 28 28 28 8
600 780 725 30 20 M27 610.0 616.5 622 650 42 30 34 34 8
700 895 840 30 24 M27 711.0 721 50 35 38 8
specified by

800 1015 950 33 24 M30 813.0 824 56 38 48 8

purchaser

900 1115 1050 33 28 M30 914.0 926 62 38 50 8

1000 1230 1160 36 28 M33 1016.0 1028 70 44 54 8
1200 1455 1380 39 32 M36 1219.0 1234 83 55 66 8
1400 1675 1590 42 36 M39 1422.0 65
1600 1915 1820 48 40 M45 1626.0 75
1800 2115 2020 48 44 M45 1829.0 85
2000 2325 2230 48 48 M45 2032.0 90
2200 2550 2440 56 52 M52 2235.0 100
2400 2760 2650 56 56 M52 2438.0 110
2600 2960 2850 56 60 M52 2620.0 110
2800 3180 3070 56 64 M52 2820.0 124
3000 3405 3290 62 68 M56 3020.0 132
 STAINLESS STEEL FLANGES
EN1092-1 PN 10

Diam- Length Neck diameter

eter
Collar Corner
of Wall thickness
thickness radii
shoul- H1 H2 H3 H4 H5 N1 N2 N3 S
F R1
der
DN Gmax
Flange
11
11,35
32 12 11 11 11 12 12
35 36 37 05 35 36 37 21 34 to
34 13 34 34 34 13 13
37
21, 34
10 12 5 2 2.5 22 35 6 35 35 7 28 30 28 4 1.8
15 12 5 2 2.5 22 38 6 38 38 7 32 35 32 4 2.0
20 14 6 2.5 3 26 40 6 40 40 8 40 45 40 4 2.3
25 14 7 2.5 3 28 40 6 40 40 10 46 52 50 4 2.6
32 14 8 3 3 30 42 6 42 42 12 56 60 60 6 2.6
40 14 8 3 3 32 45 7 45 45 15 64 70 70 6 2.6
50 16 8 3 4 28 45 8 45 45 20 74 84 84 6 2.9
65 16 8 3 4 55 32 45 10 45 45 20 92 104 104 6 2.9
80 16 10 3 4 70 34 50 10 50 50 25 105 118 120 6 3.2
100 18 10 4 4 90 40 52 12 52 52 25 131 140 140 8 3.6
125 18 10 4 4 115 44 55 12 55 55 25 156 168 170 8 4.0
150 20 10 4 4 140 44 55 12 55 55 25 184 195 190 10 4.5
200 20 11 5 4 190 44 62 16 62 62 30 234 246 246 10 6.3
250 22 12 8 235 46 68 16 68 68 292 298 298 12 6.3
300 22 12 8 285 46 68 16 68 68 342 350 348 12 7.1
350 22 13 8 330 53 68 16 68 68 385 400 408 12 7.1
400 24 14 8 380 57 72 16 72 72 440 456 456 12 7.1
450 24 15 425 63 72 16 72 488 502 502 12 7.1
500 26 16 475 67 75 16 75 542 559 559 12 7.1
600 26 18 575 75 82 18 80 642 658 658 12
700 20 670 85 18 80 746 772 12
800 20 770 96 18 90 850 876 12
900 22 860 99 20 95 950 976 12
1000 24 960 105 20 95 1052 1080 16
1200 26 1160 132 25 115 1256 1292 16
1400 143 25 1460 1496 16
1600 159 25 1666 1712 16
1800 175 30 1868 1910 16
2000 186 30 2072 2120 16
2200 202 35 2275 18
2400 218 35 2478 18
2600 224 40 2680 18
2800 244 40 2882 18
3000 257 45 3085 18
STAINLESS STEEL FLANGES
EN1092-1 PN 16
 STAINLESS STEEL FLANGES
EN1092-1 PN 16

Mating dimensions
Out-
Diam- side Bore
Out- Diam- diam- Flanges thickness
eter Bolting diameter Chamfer
side eter eter
of E
diam- of bolt of
bolt
eter circle neck
hole Num-
DN D k Size A B1 B2 B3 C1 C2 C3 C4
k ber
Flange type
11
01 01 11
21 02
01, 02 , 05, 11, 12, 13, 21 12 02 04 02 12 21 05
34 04
32 04 13
35-37
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5
50 165 125 18 4 M16 60.3 61.5 65 77 20 18 18 18 5
65 185 145 18 8 M16 76.1 77.5 81 96 20 18 18 18 6
80 200 160 18 8 M16 88.9 90.5 94 108 20 20 20 20 6
100 220 180 18 8 M16 114.3 116.0 120 134 22 20 20 20 6
125 250 210 18 8 M16 139.7 141.5 145 162 22 22 22 22 6
150 285 240 22 8 M20 168.3 170.5 174 188 24 22 22 22 6
200 340 295 22 12 M20 219.1 221.5 226 240 26 24 24 24 6
250 395 350 26 12 M24 273.0 276.5 281 294 29 26 26 26 8
300 445 400 26 12 M24 323.9 327.5 333 348 32 28 28 28 8
350 505 460 26 16 M24 355.6 359.0 365 400 35 30 30 30 8
400 565 515 30 16 M27 406.4 411.0 416 454 38 32 32 32 8
450 615 565 30 20 M27 457.0 462.0 467 500 42 34 40 40 8
500 670 620 33 20 M30 508.0 513.5 519 556 46 36 44 44 8
600 780 725 36 20 M33 610.0 616.5 622 660 55 40 54 54 8
700 895 840 36 24 M33 711.0 721 63 40 58 8
specified by
purchaser

800 1015 950 39 24 M36 813.0 824 74 41 62 8

900 1115 1050 39 28 M36 914.0 926 82 48 64 8
specified by

1000 1230 1160 42 28 M39 1016.0 1030 90 59 68 8

purchaser

1200 1455 1380 48 32 M45 1219.0 78

1400 1675 1590 48 36 M45 1422.0 84
1600 1915 1820 56 40 M52 1626.0 102
1800 2115 2020 56 44 M52 1829.0 110
2000 2325 2230 62 48 M56 2032.0 124
 STAINLESS STEEL FLANGES
EN1092-1 PN 16

Diam-
Collar eter Length Neck diameter Corner Wall thick-
thickness of radii ness
F shoulder R1 S
Gmax
DN H1 H2 H3 H4 H5 N1 N2 N3
Flange
11
11, 35
32 12 11 11 11 12 12
35 36 37 05 35 36 37 21 34 to
34 13 34 34 34 13 13
37
21, 34
10 12 5 2 2.5 22 35 6 35 35 7 28 30 28 4 1.8
15 12 5 2 2.5 22 38 6 38 38 7 32 35 32 4 2.0
20 14 6 2.5 3 26 40 6 40 40 8 40 45 40 4 2.3
25 14 7 2.5 3 28 40 6 40 40 10 46 52 50 4 2.6
32 14 8 3 3 30 42 6 42 42 12 56 60 60 6 2.6
40 14 8 3 3 32 45 7 45 45 15 64 70 70 6 2.6
50 16 8 3 4 28 45 8 45 45 20 74 84 84 6 2.9
65 16 8 3 4 55 32 45 10 45 45 20 92 104 104 6 2.9
80 16 10 3 4 70 34 50 10 50 50 25 105 118 120 6 3.2
100 18 10 4 4 90 40 52 12 52 52 25 131 140 140 8 3.6
125 18 10 4 4 115 44 55 12 55 55 25 156 168 170 8 4.0
150 20 10 5 5 140 44 55 12 55 55 25 184 195 190 10 4.5

Please see thickness table

200 20 11 6 6 190 44 62 16 62 62 30 235 246 246 10 6.3
250 22 12 10 235 46 70 16 70 68 292 298 296 12 6.3
300 24 14 10 285 46 78 16 78 68 344 350 350 12 7.1
350 26 18 10 330 57 82 16 82 68 390 400 410 12 8.0
400 28 20 10 380 63 85 16 85 72 445 456 458 12 8.0
450 30 22 425 68 83 16 87 490 502 516 12 8.0
500 32 22 475 73 84 16 90 548 559 576 12 8.0
600 32 24 575 83 88 18 95 670 658 690 12 8.8
700 26 670 83 104 18 100 755 760 760 12
800 28 770 90 108 20 105 855 864 862 12
900 30 860 94 118 20 110 955 968 962 12
1000 35 960 100 137 22 120 1058 1072 1076 16
1200 1160 160 30 1262 1282 16
1400 1346 177 30 1465 1482 16
1600 1546 204 35 1668 1696 16
1800 1746 218 35 1870 1896 16
2000 1950 238 40 2072 2100 16
STAINLESS STEEL FLANGES
EN1092-1 PN 25
 STAINLESS STEEL FLANGES
EN1092-1 PN 25

Mating dimensions Bore

Flanges thickness
Di- Bolting diameter
Diam- Outside
Out- am-
eter diameter Chamfer
side eter
of of neck E
diam- of
bolt Num- Size A B1 B2 B3 C1 C2 C3 C4
eter bolt ber
hole
DN D circle
L
k
Flange type
11
01 01 11
21 02
01, 02, 05, 11, 12, 13, 21 12 02 04 02 12 21 05
34 04
32 04 13
35-37
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5
50 165 125 18 4 M16 60.3 61.5 65 77 20 20 20 20 5
65 185 145 18 8 M16 76.1 77.5 81 96 22 22 22 22 6
80 200 160 18 8 M16 88.9 90.5 94 114 24 24 24 24 6
100 235 190 22 8 M20 114.3 116.0 120 138 26 24 24 24 6
125 270 220 26 8 M24 139.7 141.5 145 166 28 26 26 26 6
150 300 250 26 8 M24 168.3 170.5 174 194 30 28 28 28 6
200 360 310 26 12 M24 219.1 221.5 226 250 32 30 30 30 6
250 425 370 30 12 M27 273.0 276.5 281 302 35 32 32 32 8
300 485 430 30 16 M27 323.9 327.5 333 356 38 34 34 34 8
350 555 490 33 16 M30 355.6 359.5 365 408 42 38 38 38 8
400 620 550 36 16 M33 406.4 411.0 416 462 48 40 40 40 8
450 670 600 36 20 M33 457.0 462.0 467 510 54 46 46 50 8
500 730 660 36 20 M33 508.0 513.5 519 568 58 48 48 51 8
600 845 770 39 20 M36 610.0 616.5 622 670 68 48 58 66 8
700 960 875 42 24 M39 711.0 721 85 50 8
specified by
purchaser

specified by pur-

specified by pur-

800 1085 990 48 24 M45 813.0 824 95 53 8

chaser

chaser
specified by

900 1185 1090 48 28 M45 914.0 57

purchaser

1200 1320 1210 56 28 M52 1016.0 63

1400
1600
Only mating dimension fixed
1800
2000
 STAINLESS STEEL FLANGES
EN1092-1 PN 25

Diam- Length Neck diameter Cor-

Collar eter
ner Wall thickness
thickness of
radii S
F shoulder H1 H2 H3 H4 N1 N2 N3 R1
Gmax
DN Flange type
11
12 11,35
32 12 11 11 11 12
35 05 35 21 13 34 to
34 13 34 34 34 13
21, 37
34
10 12 5 22 35 6 35 28 30 28 4 1.8
15 12 5 22 38 6 38 32 35 32 4 2.0
20 14 6 26 40 6 40 40 45 40 4 2.3
25 14 7 28 40 6 40 46 52 50 4 2.6
32 14 8 30 42 6 42 56 60 60 6 2.6
40 14 8 32 45 7 45 64 70 70 6 2.6
50 16 10 34 48 8 48 75 84 84 6 2.9
65 16 11 55 38 52 10 52 90 104 104 6 2.9
80 18 12 70 40 58 12 58 105 118 120 8 3.2

Please see thickness table

100 20 14 90 44 65 12 65 134 145 142 8 3.6
125 22 16 115 48 68 12 68 162 170 162 8 4.0
150 24 18 140 52 75 12 75 192 200 192 10 4.5
200 26 18 190 52 80 16 80 244 256 252 10 6.3
250 26 18 235 60 88 18 88 298 310 304 12 7.1
300 28 20 285 67 92 18 92 352 364 364 12 8
350 32 22 332 72 100 20 100 398 418 418 12 8.0
400 34 24 380 78 110 20 110 452 472 472 12 8.8
450 36 26 425 84 110 20 110 500 520 520 12 8.8
500 38 28 475 90 125 20 125 558 580 580 12 10.0
600 40 30 575 100 125 20 115 660 684 684 12 11
700 30 129 20 125 760 780 12
800 35 138 22 135 864 882 12
900 148 24 968 982 12
1200 160 24 1070 1086 16
1400
1600
1800 Only mating dimensions fixed

2000
STAINLESS STEEL FLANGES
EN1092-1 PN 40
 STAINLESS STEEL FLANGES
EN1092-1 PN 40

Mating dimensions Bore

Flanges thickness
Bolting diameter
Diam- Outside
Diam-
eter diameter Chamfer
Outside eter
of of neck E
diameter of bolt
bolt Number Size A B1 B2 B3 C1 C2 C3 C4
D circle
DN hole
k
L
Flange type
11 01 01 11
02
01, 02 , 05, 11, 12, 13, 21 21 12 02 04 02 12 21 05
04
34 32 04 13
10 90 60 14 4 M12 17.2 18.0 21 31 14 16 16 16 3
15 95 65 14 4 M12 21.3 22.0 25 35 14 16 16 16 3
20 105 75 14 4 M12 26.9 27.5 31 42 16 18 18 18 4
25 115 85 14 4 M12 33.7 34.5 38 49 16 18 18 18 4
32 140 100 18 4 M16 42.4 43.5 47 59 18 18 18 18 5
40 150 110 18 4 M16 48.3 49.5 53 67 18 18 18 18 5
50 165 125 18 4 M16 60.3 61.5 65 77 20 20 20 20 5
65 185 145 18 8 M16 76.1 77.5 81 96 22 22 22 22 6
80 200 160 18 8 M16 88.9 90.5 94 114 24 24 24 24 6
100 235 190 22 8 M20 114.3 116.0 120 138 26 24 24 24 6
125 270 220 26 8 M24 139.7 141.5 145 166 28 26 26 26 6
150 300 250 26 8 M24 168.3 170.5 174 194 30 28 28 28 6
200 375 320 30 12 M27 219.1 221.5 226 250 36 36 36 36 6
250 450 385 33 12 M30 273.0 276.5 281 312 42 38 38 38 8
300 515 450 33 16 M30 323.9 327.5 333 368 52 42 42 42 8
350 580 510 36 16 M33 355.6 359.5 365 418 58 46 46 46 8
400 660 585 39 16 M36 406.4 411.0 416 472 65 50 50 50 8
450 685 610 39 20 M36 457.0 462.0 467 510 57 57 57 8
Specified by
purchaser

500 755 670 42 20 M39 508.0 513.5 519 572 57 57 57 8

600 890 795 48 20 M45 610.0 616.5 622 676 72 72 72 8

700
800
900
1000 Only mating dimension
1200
1400
1600
 STAINLESS STEEL FLANGES
EN1092-1 PN 40

Length Neck diameter

Diameter
Collar Corner Wall thick-
of
thickness radii ness
shoulder H1 H2 H3 H4 N1 N2 N3
F R1 S
Gmax
DN

Flange type
11
11,
32 12 11 11 11 12 12
35 05 35 21 34 35
34 13 34 34 34 13 13
21
10 12 5 22 35 6 35 28 30 28 4 1.8
15 12 5 22 38 6 38 32 35 32 4 2.0
20 14 6 26 40 6 40 40 45 40 4 2.3
25 14 7 28 40 6 40 46 52 50 4 2.6
32 14 8 30 42 6 42 56 60 60 6 2.6
40 14 8 32 45 7 45 64 70 70 6 2.6
50 16 10 34 48 8 48 75 84 84 6 2.9

Please see thickness table

65 16 11 55 38 52 10 52 90 104 104 6 2.9
80 18 12 70 40 58 12 58 105 118 120 8 3.2
100 20 14 90 44 65 12 65 134 145 142 8 3.6
125 22 16 115 48 68 12 68 162 170 162 8 4.0
150 24 18 140 52 75 12 75 192 200 192 10 4.5
200 28 20 190 52 88 16 88 244 260 254 10 6.3
250 30 22 235 60 105 18 105 306 312 312 12 7.1
300 34 25 285 67 115 18 115 362 380 378 12 8
350 36 28 330 72 125 20 125 408 424 432 12 8.8
400 42 32 380 78 135 20 135 462 478 498 12 11.0
450 46 425 84 135 20 500 522 522 12 12.5
500 50 475 90 140 20 562 576 576 12 14.2
600 54 575 100 150 20 666 686 686 12 16
700
800
900
1000 Only mating dimension fixed
1200
1400
1600
STAINLESS STEEL FLANGES
EN1092-1 PN 63
 STAINLESS STEEL FLANGES
EN1092-1 PN 63

Mating dimensions Bore

diam- Flanges thickness
Out- Bolting Outside eter
Diameter Diameter diameter
side
of bolt of of neck
diam-
circle bolt hole Num- A
eter Size B1 C1 C2 C3 C4
k L ber
D
DN
Flange type

11 01 01 11
01 , 05, 11, 12, 13, 21 21 12 12 21 05
13

10 100 70 14 4 M12 17.2 18.0 20 20 20

15 105 75 14 4 M12 21.3 22.0 20 20 20
20 130 90 18 4 M16 26.9 27.5 22 22 18 22
25 140 100 18 4 M16 33.7 34.5 24 24 18 24
32 155 110 22 4 M20 42.4 43.5 24 24 18 26
40 170 125 22 4 M20 48.3 49.5 26 26 18 28
50 180 135 22 4 M20 60.3 61.5 26 26 20 26
65 205 160 22 8 M20 76.1 77.5 26 26 22 26
80 215 170 22 8 M20 88.9 90.5 30 28 24 28
100 250 200 26 8 M24 114.3 116.0 32 30 24 30
125 295 240 30 8 M27 139.7 141.5 34 34 26 34
150 345 280 33 8 M30 168.3 170.5 36 36 28 36
200 415 345 36 12 M23 219.1 221.5 48 42 30 42
250 470 400 36 12 M33 273.0 276.5 55 46 32 46
300 530 460 36 16 M33 323.9 327.5 65 52 34 52
350 600 525 39 16 M36 355.6 359.5 72 56 38 56
400 670 585 42 16 M39 406.4 411.0 80 60 40 60
500
600
700
800 Only mating dimension fixed
900
1000
1200
STAINLESS STEEL FLANGES
EN1092-1 PN 63

Length Neck diameter

Diameter
Corner
of Wall thickness
radii
shoulder H1 H2 H3 N1 N2 N3 S
R1
Gmax
DN
Flange type

11 12 13
12 11 11 12
05 11 21 21 11
13 13

28 45 6 32 40 40 4
10 28 45 6 34 43 45 4
15 30 48 8 42 52 50 4
20 32 58 8 52 60 61 4
25 32 60 8 62 68 68 6
32 34 62 10 70 80 82 6

Please see thickness table

40 36 62 10 82 90 90 6
50 45 40 68 12 98 112 105 6
65 60 44 72 12 112 125 122 8
80 80 52 78 12 138 152 146 8
100 105 56 88 12 168 185 177 8
125 130 60 95 12 202 215 204 10
150 180 110 16 256 264 10
200 220 125 18 316 320 12
250 270 140 18 372 378 12
300 310 150 20 420 343 12
350 360 160 20 475 490 12
400
500
600
700
Only mating dimension
800
900
1000
1200
STAINLESS STEEL FLANGES
EN1092-1 PN 100
 STAINLESS STEEL FLANGES
EN1092-1 PN 100

Mating dimensions

Outside Bore
Diameter Diameter Flanges thickness
Outside Bolting diameter diameter
of bolt of of neck
diameter
circle bolt hole A
D
DN k L
Number Size B1 C1 C2 C3 C4
Flange type
11 "01 01 11
01 , 05, 11, 12, 13, 21 21 12 12 21 05
13
10 100 70 14 4 M12 17.2 18.0 20 20 20 20
15 105 75 14 4 M12 21.3 22.0 20 20 20 20
20 130 90 18 4 M16 26.9 27.5 22 22 22 22
25 140 100 18 4 M16 33.7 34.5 24 24 24 24
32 155 110 22 4 M20 42.4 43.5 24 24 26 24
40 170 125 22 4 M20 48.3 49.5 26 26 28 26
50 195 145 26 4 M24 60.3 61.5 28 28 30 28
65 220 170 26 8 M24 76.1 77.5 30 30 34 30
80 230 180 26 8 M24 88.9 90.5 34 32 36 32
100 265 210 30 8 M27 114.3 116.0 36 36 40 36
125 315 250 33 8 M30 139.7 141.5 42 40 40 40
150 355 290 33 12 M30 168.3 170.5 48 44 44 44
200 430 360 36 12 M33 219.1 221.5 60 52 52 52
250 505 430 39 12 M36 273.0 276.5 72 60 60 60
300 585 500 42 16 M39 323.9 327.5 84 68 68 68
350 655 560 48 16 M45 355.6 359.5 95 74 74 74
400
Only mating dimension fixed
500
 STAINLESS STEEL FLANGES
EN1092-1 PN 100

Diameter
Length Neck diameter Corner Wall thick-
of
radii ness
shoulder
R1 S
Gmax
DN H1 H2 H3 N1 N2 N3
Flange type

12 11 11 12 11 12 13 21
05 11 21 11
13 13

10 28 45 6 32 40 40 4
15 28 45 6 34 43 45 4
20 30 48 8 42 52 50 4
25 32 58 8 52 60 61 4
32 32 60 8 62 68 68 6
40 34 62 10 70 80 82 6

Please see thickness table

50 36 68 10 90 95 96 6
65 45 40 76 12 108 118 118 6
80 60 44 78 12 120 130 128 8
100 80 52 90 12 150 158 150 8
125 105 56 105 12 180 188 185 8
150 130 60 115 12 210 225 216 10
200 180 130 16 278 278 10
250 210 157 18 340 340 12
300 260 170 18 400 407 12
350 300 189 20 460 460 12
400
Only mating dimension fixed
500
 STAINLESS STEEL FLANGES
EN1092-1
FLANGES FACING DIMENSIONS
d
DN PN2.5 PN6 PN10 PN16 PN25 PN40 PN63 PN100 PN160 PN250 PN320 PN400
mm mm mm mm mm mm mm mm mm mm mm mm
10.0 35.0 35.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0
15.0 40.0 40.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0 45.0
20.0 50.0 50.0 58.0 58.0 58.0 58.0 58.0 58.0 58.0 58.0 58.0 58.0
25.0 60.0 60.0 68.0 68.0 68.0 68.0 68.0 68.0 68.0 68.0 68.0 68.0
32.0 70.0 70.0 78.0 78.0 78.0 78.0 78.0 78.0 78.0 78.0 78.0 78.0
40.0 80.0 80.0 88.0 88.0 88.0 88.0 88.0 88.0 88.0 88.0 88.0 88.0
50.0 90.0 90.0 102.0 102.0 102.0 102.0 102.0 102.0 102.0 102.0 102.0 102.0
65.0 110.0 110.0 122.0 122.0 122.0 122.0 122.0 122.0 122.0 122.0 122.0 122.0
80.0 128.0 128.0 138.0 138.0 138.0 138.0 138.0 138.0 138.0 138.0 138.0 138.0
100.0 148.0 148.0 158.0 158.0 162.0 162.0 162.0 162.0 162.0 162.0 162.0 162.0
125.0 178.0 178.0 188.0 188.0 188.0 188.0 188.0 188.0 188.0 188.0 188.0 188.0
150.0 202.0 202.0 212.0 212.0 218.0 218.0 218.0 218.0 218.0 218.0 218.0 218.0
200.0 258.0 258.0 268.0 268.0 278.0 285.0 285.0 285.0 285.0 285.0 285.0 285.0
250.0 312.0 312.0 320.0 320.0 335.0 345.0 345.0 345.0 345.0 345.0 345.0
300.0 365.0 365.0 370.0 378.0 395.0 410.0 410.0 410.0 410.0
350.0 415.0 415.0 430.0 438.0 450.0 465.0 465.0 465.0
400.0 465.0 465.0 482.0 490.0 505.0 535.0 535.0 435.0
450.0 520.0 520.0 532.0 550.0 555.0 560.0 560.0 560.0
500.0 570.0 570.0 585.0 610.0 615.0 615.0 615.0 615.0
600.0 670.0 670.0 686.0 725.0 720.0 735.0 735.0
700.0 775.0 775.0 800.0 798.0 820.0 840.0 840.0
800.0 880.0 880.0 905.0 900.0 930.0 960.0 960.0
900.0 980.0 980.0 1005.0 1000.0 1030.0 1070.0 1070.0
1000.0 1080.0 1080.0 1110.0 1115.0 1140.0 1180.0 1180.0
1200.0 1280.0 1295.0 1330.0 1330.0 1350.0 1380.0 1380.0
1400.0 1480.0 1510.0 1535.0 1530.0 1560.0 1600.0
1600.0 1690.0 1710.0 1760.0 1750.0 1780.0 1815.0
1800.0 1890.0 1920.0 1960.0 1950.0 1985.0
2000.0 2090.0 2125.0 2170.0 2150.0 2210.0
2200.0 2295.0 2335.0 2370.0
2400.0 2498.0 2545.0 2570.0
2600.0 2695.0 2750.0 2780.0
2800.0 2910.0 2960.0 3000.0
3000.0 3110.0 3160.0 3210.0
3200.0 3310.0 3370.0
3400.0 3510.0 3580.0
3600.0 3720.0 3790.0
3800.0 3920.0
4000.0 4120.0
 TSINGSHAN

ANSI FLANGES

Weld Neck Flange

Threaded Flange
Slip On Flange
Lap Joint Flange
Socket Weld Flange
Blind Flange

Website: www.pipefittingweb.com Email: [email protected] Fax: 886-423112578

 STAINLESS STEEL FLANGES
ANSI B16.5 Class 150
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. Bolt
No./Dia.
Pipe O T R X Circle L2 H B2 L B r L3 B3 D
of Holes
Size Dia.
1/2 3.50 0.44 1.38 1.19 4-0.62 2.38 1.88 0.84 0.62 0.62 0.88 0.12 0.62 0.90 0.38
3/4 3.88 0.50 1.69 1.50 4-0.62 2.75 2.06 1.05 0.82 0.62 1.09 0.12 0.62 1.11 0.44
1 4.25 0.56 2.00 1.94 4-0.62 3.12 2.19 1.32 1.05 0.69 1.36 0.12 0.69 1.38 0.50
1-1/4 4.62 0.62 2.50 2.31 4-0.62 3.50 2.25 1.66 1.38 0.81 1.70 0.19 0.81 1.72 0.56
1-1/2 5.00 0.68 2.88 2.56 4-0.62 3.88 2.44 1.90 1.61 0.88 1.95 0.25 0.88 1.97 0.62
2 6.00 0.75 3.62 3.06 4-0.75 4.75 2.50 2.38 2.07 1.00 2.44 0.31 1.00 2.46 0.69
2-1/2 7.00 0.88 4.12 3.56 4-0.75 5.50 2.75 2.88 2.47 1.12 2.94 0.31 1.12 2.97 0.75
3 7.50 0.94 5.00 4.25 4-0.75 6.00 2.75 3.50 3.07 1.19 3.57 0.38 1.19 3.60 0.81
3-1/2 8.50 0.94 5.50 4.81 8-0.75 7.00 2.81 4.00 3.55 1.25 4.07 0.38 1.25 4.10 0.88
4 9.00 0.94 6.19 5.31 8-0.75 7.50 3.00 4.50 4.03 1.31 4.57 0.44 1.31 4.60 0.94
5 10.00 0.94 7.31 6.44 8-0.88 8.50 3.50 5.56 5.05 1.44 5.66 0.44 1.44 5.69 0.94
6 11.00 1.00 8.50 7.56 8-0.88 9.50 3.50 6.63 6.07 1.56 6.72 0.50 1.56 6.75 1.06
8 13.50 1.12 10.62 9.69 8-0.88 11.75 4.00 8.63 7.98 1.75 8.72 0.50 1.75 8.75 1.25
10 16.00 1.19 12.75 12.00 12-1.00 14.25 4.00 10.75 10.02 1.94 10.88 0.50 1.94 10.92 1.31
12 19.00 1.25 15.00 14.38 12-1.00 17.00 4.50 12.75 12.00 2.19 12.88 0.50 2.19 12.92 1.56
14 21.00 1.38 16.25 15.75 12-1.12 18.75 5.00 14.00 13.25 2.25 14.14 0.50 3.12 14.18 1.63
16 23.50 1.44 18.50 18.00 16-1.12 21.25 5.00 16.00 15.25 2.50 16.16 0.50 3.44 16.19 1.75
18 25.00 1.56 21.00 19.88 16-1.25 22.75 5.50 18.00 17.25 2.69 18.18 0.50 3.81 18.20 1.94
20 27.50 1.69 23.00 22.00 20-1.25 25.00 5.69 20.00 19.25 2.88 20.20 0.50 4.06 20.25 2.13
22 29.50 1.81 25.25 24.25 20-1.38 27.25 5.88 22.00 21.25 3.13 22.22 0.50 4.25 22.25 2.38
24 32.00 1.88 27.25 26.12 20-1.38 29.50 6.00 24.00 23.25 3.25 24.25 0.50 4.38 24.25 2.50
Dimensions in inches.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 300
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. No. & Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 B3 D C THr
Size Holes Dia.
1/2 3.75 0.56 1.38 1.5. 4-0.62 2.62 2.06 0.84 0.62 0.88 0.88 0.12 0.88 0.90 0.38 0.93 0.62
3/4 4.62 0.62 1.69 1.88 4-0.75 3.25 2.25 1.05 0.82 1.00 1.09 0.12 1.00 1.11 0.44 1.14 0.62
1 4.88 0.69 2.00 2.12 4-0.75 3.50 2.44 1.32 1.05 1.06 1.36 0.12 1.06 1.38 0.50 1.41 0.69
1-1/4 5.25 0.75 2.50 2.50 4-0.75 3.88 2.56 1.66 1.38 1.06 1.70 0.19 1.06 1.72 0.56 1.75 0.81
1-1/2 6.12 0.81 2.88 2.75 4-0.88 4.50 2.69 1.90 1.61 1.19 1.95 0.25 1.19 1.97 0.62 1.99 0.88
2 6.50 0.88 3.62 3.31 8-0.75 5.00 2.75 2.38 2.07 1.31 2.44 0.31 1.31 2.46 0.69 2.50 1.12
2-1/2 7.50 1.00 4.12 3.94 8-0.88 5.88 3.00 2.88 2.47 1.50 2.94 0.31 1.50 2.97 0.75 3.00 1.25
3 8.25 1.12 5.00 4.62 8-0.88 6.62 3.12 3.50 3.07 1.69 3.57 0.38 1.69 3.60 0.81 3.63 1.25
3-1/2 9.00 1.19 5.50 5.25 8-0.88 7.25 3.19 4.00 3.55 1.75 4.07 0.38 1.75 4.10 4.13 1.44
4 10.00 1.25 6.19 5.75 8-0.88 7.88 3.38 4.50 4.03 1.88 4.57 0.44 1.88 4.60 4.63 1.44
5 11.00 1.38 7.31 7.00 8-0.88 9.25 3.88 5.56 5.05 2.00 5.66 0.44 2.00 5.69 5.69 1.69
6 12.50 1.44 8.50 8.12 12-0.88 10.62 3.88 6.63 6.07 2.06 6.72 0.50 2.06 6.75 6.75 1.81
8 15.00 1.62 10.62 10.25 12-1.00 13.00 4.38 8.63 7.98 2.44 8.72 0.50 2.44 8.75 8.75 2.00
10 17.50 1.88 12.75 12.62 16-1.12 15.25 4.62 10.75 10.02 2.62 10.88 0.50 3.75 10.92 10.88 2.19
12 20.50 2.00 15.00 14.75 16-1.25 17.75 5.12 12.75 12.00 2.88 12.88 0.50 4.00 12.92 12.94 2.38
14 23.00 2.12 16.25 16.75 20-1.25 20.25 5.62 14.00 13.25 3.00 14.14 0.50 4.38 14.18 14.19 2.50
16 25.50 2.25 18.50 19.00 20-1.38 22.50 5.75 16.00 15.25 3.25 16.16 0.50 4.75 16.19 16.19 2.69
18 28.00 2.38 21.00 21.00 24-1.38 24.75 6.25 18.00 17.25 3.50 18.18 0.50 5.12 18.20 18.19 2.75
20 30.50 2.50 23.00 23.12 24-1.38 27.00 6.38 20.00 19.25 3.75 20.20 0.50 5.50 20.25 20.19 2.88
22 33.00 2.63 25.25 25.25 24-1.63 29.25 6.50 22.00 21.25 4.00 22.22 0.50 5.75 22.25 22.19 3.13
24 36.00 2.75 27.25 27.62 24-1.62 32.00 6.62 24.00 23.25 4.19 24.25 0.50 6.00 24.25 24.19 3.25
Dimensions in inches.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 400
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. No.& Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 B3 D C THr
Size Holes Dia.
1/2 3.75 0.56 1.38 1.50 4-0.62 2.62 2.06 0.84 0.88 0.88 0.12 0.88 0.90 0.38 0.93 0.62
3/4 4.62 0.62 1.69 1.88 4-0.75 3.25 2.25 1.05 1.00 1.09 0.12 1.00 1.11 0.44 1.14 0.62
1 4.88 0.69 2.00 2.12 4-.075 3.50 2.44 1.32 1.06 1.36 0.12 1.06 1.38 0.50 1.41 0.69
1-1/4 5.25 0.81 2.50 2.50 4-0.75 3.88 2.62 1.66 1.12 1.70 0.19 1.12 1.72 0.56 1.75 0.81
1-1/2 6.12 0.88 2.88 2.75 4-0.88 4.50 2.75 1.90 1.25 1.95 0.25 1.25 1.97 0.62 1.99 0.88
purchaser.

2 6.50 1.00 3.62 3.31 8-0.75 5.00 2.88 2.38 1.44 2.44 0.31 1.44 2.46 0.69 2.50 1.12
2-1/2 7.50 1.12 4.12 3.94 8-0.88 5.88 3.12 2.88 1.62 2.94 0.31 1.62 2.97 0.75 3.00 1.25
3 8.25 1.25 5.00 4.62 8-0.88 6.62 3.25 3.50 1.81 3.57 0.38 1.81 3.60 0.81 3.63 1.38
3-1/2 9.00 1.38 5.50 5.25 8-1.00 7.25 3.38 4.00 1.94 4.07 0.38 1.94 4.10 4.13 1.56
To be specified by

4 10.00 1.38 6.19 5.75 8-1.00 7.88 3.50 4.50 2.00 4.57 0.44 2.00 4.60 4.63 1.44
5 11.00 1.50 7.31 7.00 8-1.00 9.25 4.00 5.56 2.12 5.66 0.44 2.12 5.69 5.69 1.69
6 12.5 1.62 8.50 8.12 12-1.00 10.62 4.06 6.63 2.25 6.72 0.50 2.25 6.75 6.75 1.81
8 15.00 1.88 10.62 10.25 12-1.12 13.00 4.62 8.63 2.69 8.72 0.50 2.69 8.75 8.75 2.00
10 17.5 2.12 12.75 12.62 16-1.25 15.25 4.88 10.75 2.88 10.88 0.50 4.00 10.92 10.88 2.19
12 20.5 2.25 15.00 14.75 16-1.38 17.75 5.38 12.75 3.12 12.88 0.50 4.25 12.92 12.94 2.38
14 23.00 2.38 16.25 16.75 20-1.38 20.25 5.88 14.00 3.31 14.14 0.50 4.62 14.18 14.19 2.50
16 25.5 2.50 18.50 19.00 20-1.50 22.50 6.00 16.00 3.69 16.16 0.50 5.00 16.19 16.19 2.69
18 28.00 2.62 21.00 21.00 24-1.50 24.75 6.50 18.00 3.88 18.18 0.50 5.38 18.20 18.19 2.75
20 30.5 2.75 23.00 23.12 24-1.62 27.00 6.62 20.00 4.00 20.20 0.50 5.75 20.25 20.19 2.88
22 33.00 2.88 25.25 25.25 24-1.75 29.25 6.75 22.00 4.25 22.22 0.50 6.00 22.25 -- --
24 36.00 3.00 27.25 27.62 24-1.88 32.00 6.88 24.00 4.50 24.25 0.50 6.25 24.25 24.19 3.25
Dimensions in inches.
1. Sizes NPS 1/2 through 3-1/2 are same as Class 600 flanges.
2. 1/4 in. raised face not included in dimensions T, L and L2.
3. Bolt hole diameter 1/8 in. larger than bolt diameter.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 600
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. No.& Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 B3 D C THr
Size Holes Dia.
1/2 3.75 0.56 1.38 1.50 4-0.62 2.62 2.06 0.84 0.88 0.88 0.12 0.88 0.90 0.38 0.93 0.62
3/4 4.62 0.62 1.69 1.88 4-0.75 3.25 2.25 1.05 1.00 1.09 0.12 1.00 1.11 0.44 1.14 0.62
1 4.88 0.69 2.00 2.12 4-.075 3.50 2.44 1.32 1.06 1.36 0.12 1.06 1.38 0.50 1.41 0.69
1-1/4 5.25 0.81 2.50 2.50 4-0.75 3.88 2.62 1.66 1.12 1.70 0.19 1.12 1.72 0.56 1.75 0.81
1-1/2 6.12 0.88 2.88 2.75 4-0.88 4.50 2.75 1.90 1.25 1.95 0.25 1.25 1.97 0.62 1.99 0.88
purchaser.

2 6.50 1.00 3.62 3.31 8-0.75 5.00 2.88 2.38 1.44 2.44 0.31 1.44 2.46 0.69 2.50 1.12
2-1/2 7.50 1.12 4.12 3.94 8-0.88 5.88 3.12 2.88 1.62 2.94 0.31 1.62 2.97 0.75 3.00 1.25
3 8.25 1.25 5.00 4.62 8-0.88 6.62 3.25 3.50 1.81 3.57 0.38 1.81 3.60 0.81 3.63 1.38
3-1/2 9.00 1.38 5.50 5.25 8-1.00 7.25 3.38 4.00 1.94 4.07 0.38 1.94 4.10 4.13 1.56
To be specified by

4 10.75 1.50 6.19 6.00 8-1.00 8.50 4.00 4.50 2.12 4.57 0.44 2.12 4.60 4.63 1.62
5 13.00 1.75 7.31 7.44 8-1.12 10.50 4.50 5.56 2.38 5.66 0.44 2.38 5.69 5.69 1.88
6 14.00 1.88 8.50 8.75 12-1.12 11.50 4.62 6.63 2.62 6.72 0.50 2.62 6.75 6.75 2.00
8 16.50 2.19 10.62 10.75 12-1.25 13.75 5.25 8.63 3.00 8.72 0.50 3.00 8.75 8.75 2.25
10 20.00 2.50 12.75 13.50 16-1.38 17.00 6.00 10.75 3.38 10.88 0.50 4.38 10.92 10.88 2.56
12 22.00 2.62 15.00 15.75 20-1.38 19.25 6.12 12.75 3.62 12.88 0.50 4.62 12.92 12.94 2.75
14 23.75 2.75 16.25 17.00 20-1.50 20.75 6.50 14.00 3.69 14.14 0.50 5.00 14.18 14.19 2.88
16 27.00 3.00 18.50 19.50 20-1.62 23.75 7.00 16.00 4.19 16.16 0.50 5.50 16.19 18.19 3.06
18 29.25 3.25 21.00 21.50 20-1.75 25.75 7.25 18.00 4.62 18.18 0.50 6.00 18.20 18.10 3.12
20 32.00 3.50 23.00 24.00 24-1.75 28.50 7.50 20.00 5.00 20.20 0.50 6.50 20.25 20.19 3.25
22 34.25 3.75 25.25 26.25 24-1.75 30.63 7.75 22.00 5.25 22.22 0.50 6.88 22.25 -- --
24 37.00 4.00 27.25 28.25 24-2.00 33.00 8.00 24.00 5.50 24.25 0.50 7.25 24.25 24.19 3.62
Dimensions in inches.
1. Sizes NPS 1/2 through 3-1/2 are same as Class 400 flanges.
2. 1/4 in. raised face not included in dimensions T, L and L2.
3. Bolt hole diameter 1/8 in. larger than bolt diameter.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 900
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. No.& Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 B3 THr
Size Holes Dia.
Sizes 1/2" Thru 2-1/2" Are Identical To Class 1500.
3 9.50 1.50 5.00 5.00 8-1.00 7.50 4.00 3.50 2.13 3.57 0.38 2.13 3.60 1.63
To be specified by purchaser.

4 11.50 1.75 6.19 6.25 8-1.25 9.25 4.50 4.50 2.75 4.57 0.44 2.75 4.60 1.88
5 13.75 2.00 7.31 7.50 8-1.38 11.00 5.00 5.56 3.13 5.66 0.44 3.13 5.69 2.13
6 15.00 2.19 8.50 9.25 12-1.25 12.50 5.50 6.63 3.38 6.72 0.50 3.38 6.75 2.25
8 18.50 2.50 10.63 11.75 12-1.50 15.50 6.38 8.63 4.00 8.72 0.50 4.50 8.75 2.50
10 21.50 2.75 12.75 14.50 16-1.50 18.50 7.25 10.75 4.25 10.88 0.50 5.00 10.92 2.81
12 24.00 3.13 15.00 16.50 20-1.50 21.00 7.88 12.75 4.63 12.88 0.50 5.63 12.92 3.00
14 25.25 3.38 16.25 17.75 20-1.63 22.00 8.38 14.00 5.13 14.14 0.50 6.13 14.18 3.25
16 27.75 3.50 18.50 20.00 20-1.75 24.25 8.50 16.00 5.25 16.16 0.50 6.50 16.19 3.38
18 31.00 4.00 21.00 22.25 20-2.00 27.00 9.00 18.00 6.00 18.18 0.50 7.50 18.20 3.50
20 33.75 4.25 23.00 24.50 20-2.13 29.50 9.75 20.00 6.25 20.20 0.50 8.25 20.25 3.63
24 41.00 5.50 27.25 29.50 20-2.63 35.50 11.50 24.00 8.00 24.25 0.50 10.50 24.25 4.00
Dimensions in inches.
1. Sizes NPS 1/2 through 2-1/2 are same as Class 1500 flanges.
2. 1/4 in. raised face not included in dimensions T, L and L2.
3. Bolt hole diameter 1/8 in. larger than bolt diameter.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 1500
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Socket Weld Flange Blind Flange

Nom. No.& Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 D B3 THr
Size Holes Dia.
1/2 4.75 0.88 1.38 1.50 4-0.88 3.25 2.38 0.84 1.25 0.88 0.13 1.25 0.38 0.90 0.88
3/4 5.13 1.00 1.69 1.75 4-0.88 3.50 2.75 1.05 1.38 1.09 0.13 1.38 0.44 1.11 1.00
1 5.88 1.13 2.00 2.06 4-1.00 4.00 2.88 1.32 1.63 1.36 0.13 1.63 0.50 1.38 1.13
1-1/4 6.25 1.13 2.50 2.50 4-1.00 4.38 2.88 1.66 1.63 1.70 0.19 1.63 0.56 1.72 1.19
purchaser.

1-1/2 7.00 1.25 2.88 2.75 4-1.13 4.88 3.25 1.90 1.75 1.95 0.25 1.75 0.63 1.97 1.25
2 8.50 1.50 3.63 4.13 8-1.00 6.50 4.00 2.38 2.25 2.44 0.31 2.25 0.69 2.46 1.50
2-1/2 9.63 1.63 4.13 4.88 8-1.13 7.50 4.13 2.88 2.50 2.94 0.31 2.50 0.75 2.97 1.88
3 10.50 1.88 5.00 5.25 8-1.25 8.00 4.63 3.50 2.88 3.57 0.38 2.88 -- 3.60 2.00
To be specified by

4 12.25 2.13 6.19 6.38 8-1.38 9.50 4.88 4.50 3.56 4.57 0.44 3.56 -- 4.60 2.25
5 14.75 2.88 7.31 7.75 8-1.63 11.50 6.13 5.56 4.13 5.66 0.44 4.13 -- 5.69 2.50
6 15.50 3.25 8.50 9.00 12-1.50 12.50 6.75 6.63 4.69 6.72 0.50 4.69 -- 6.75 2.75
8 19.00 3.63 10.63 11.50 12-1.75 15.50 8.38 8.63 5.63 8.72 0.50 5.63 -- 8.75 3.00
10 23.00 4.25 12.75 14.50 12-2.00 19.00 10.00 10.75 6.25 10.88 0.50 7.00 -- 10.92 3.31
12 26.50 4.88 15.00 17.75 16-2.13 22.50 11.13 12.75 7.13 12.88 0.50 8.63 -- 12.92 3.63
14 29.50 5.25 16.25 19.50 16-2.38 25.00 11.75 14.00 -- -- 0.50 9.50 -- 14.18 --
16 32.50 5.75 18.50 21.75 16-2.63 27.75 12.25 16.00 -- -- 0.50 10.25 -- 16.19 --
18 36.00 6.38 21.00 23.50 16-2.88 30.50 12.88 18.00 -- -- 0.50 10.88 -- 18.20 --
20 38.75 7.00 23.00 25.25 16-3.13 32.75 14.00 20.00 -- -- 0.50 11.50 -- 20.25 --
24 46.00 8.00 27.25 30.00 16-3.63 39.00 16.00 24.00 -- -- 0.50 13.00 -- 24.25 --
Dimensions in inches.
1. 1/4 in. raised face not included in dimensions T, L and L2.
2. Bolt hole diameter 1/8 in. larger than bolt diameter.
 STAINLESS STEEL FLANGES
ANSI B16.5 Class 2500
Flanges

Weld Neck Flange Threaded Flange Slip On Flange

Lap Joint Flange Blind Flange

Nom. No.& Bolt

Pipe O T R X Dia. of Circle L2 H B2 L B r L3 B3 THr
Size Holes Dia.
1/2 5.25 1.19 1.38 1.69 4-0.88 3.50 2.88 0.84 1.56 0.88 0.13 1.56 0.90 1.13
purchaser.

3/4 5.50 1.25 1.69 2.00 4-0.88 3.75 3.13 1.05 1.69 1.09 0.13 1.69 1.11 1.25
1 6.25 1.38 2.00 2.25 4-1.00 4.25 3.50 1.32 1.88 1.36 0.13 1.88 1.38 1.38
1-1/4 7.25 1.50 2.50 2.88 4-1.13 5.13 3.75 1.66 2.06 1.70 0.18 2.06 1.72 1.50
1-1/2 8.00 1.75 2.88 3.13 4-1.25 5.75 4.38 1.90 2.38 1.95 0.25 2.38 1.97 1.75
2 9.25 2.00 3.63 3.75 8-1.13 6.75 5.00 2.38 2.75 2.44 0.31 2.75 2.46 2.00
To be specified by

2-1/2 10.50 2.25 4.13 4.50 8-1.25 7.75 5.63 2.88 3.13 2.94 0.31 3.13 2.97 2.25
3 12.00 2.63 5.00 5.25 8-1.38 9.00 6.63 3.50 3.63 3.57 0.37 3.63 3.60 2.50
4 14.00 3.00 6.19 6.50 8-1.63 10.75 7.50 4.50 4.25 4.57 0.44 4.25 4.60 2.75
5 16.50 3.63 7.31 8.00 8-1.88 12.75 9.00 5.56 5.13 5.66 0.44 5.13 5.69 3.00
6 19.00 4.25 8.50 9.25 8-2.13 14.50 10.75 6.63 6.00 6.72 0.50 6.00 6.75 3.25
8 21.75 5.00 10.63 12.00 12-2.13 17.25 12.50 8.63 7.00 8.72 0.50 7.00 8.75 3.75
10 26.50 6.50 12.75 14.75 12-2.63 21.25 16.50 10.75 9.00 10.88 0.50 9.00 10.92 4.25
12 30.00 7.25 15.00 17.38 12-2.88 24.38 18.25 12.75 10.00 12.88 0.50 10.00 12.92 4.75
Dimensions in inches.
1. 1/4 in. raised face not included in dimensions T, L and L2.
2. Bolt hole diameter 1/8 in. larger than bolt diameter.
 STAINLESS STEEL FLANGES
Dimensional Tolerance
ANSI B16.5

Threaded, Socket-Welding, Slip-On, Lap Joint and Blind Weld Neck

Outside 6” and below ±1.5mm 6” and below ±1.5mm
Outside Diameter
Diameter 8” ~ 24” ±2.0mm 8” ~ 24” ±2.0mm
*
* over 24” ±3.0mm over 24” ±3.0mm
Threaded Within limits on boring +0.8mm
1/2” ~ 10”
gauge -0mm
2-1/2” and +0.5mm
Inside Diameter Socket-Welding, below -0mm Inside Diameter 12” ~ 18” ±1.6mm
+0.8mm
Slip-On and 3” ~ 10”
-0mm
Lap-Joint +3.2mm
+1.6mm 20” and above
12” and above -1.6mm
-0mm
Outside +3.0mm +3.0mm
Diameter of Hub
Diameter of Hub 1/2” ~ 24” -1.0mm 1/2” ~ 24” -1.0mm
at Base *
*
1/16” Raised Face ±0.8mm 1/16” Raised Face ±0.8mm
Diameter of 1/4” Raised Face Diameter of 1/4” Raised Face
Contact Face Tongue & Groove ±0.5mm Contact Face Tongue & Groove ±0.5mm
Male, Female Male, Female
1/2” ~ 5” +2.4mm
Diameter of Diameter of Hub -0.8mm
Same as for Inside Diameter
Counter Bore at Point of Welding 6” and above +4.0mm
-0.8mm
6” and below ±1.0mm Bore 6” and below ±1.0mm
Bore
8” ~ 24” ±1.6mm 8” ~ 24” ±1.6mm
Eccentricity of Bore ±0.8mm Eccentricity of Bore ±0.8mm
Drilling Diameter of Bolt Drilling Diameter of Bolt
±0.5mm ±0.5mm
Hole Hole
Bolt hole spacing Bolt hole spacing
±0.8mm ±0.8mm
24” and above 24” and above
+1.6mm +1.6mm
1/2” ~ 4” 1/2” ~ 4”
-0mm -0mm
+2.0mm +2.0mm
5” ~ 12” 5” ~ 12”
-0mm -0mm
Thickness Thickness
+3.0mm +3.0mm
14” ~ 18” 14” ~ 18”
-0mm -0mm
+4.0mm +4.0mm
20” and above 20” and above
-0mm -0mm
Length Through 1/2” ~ 10” ±1.6mm Length Through 1/2” ~ 10” ±1.6mm
the Hub * 12” and above ±3.0mm the Hub 12” and above ±3.0mm
* Tolerances not listed in B16.5

Welding Bevel Standards

For Wall Thickness “t” 3/16” to 3/4” including For Wall Thickness “t” greater than 3/4”
 STAINLESS STEEL FLANGES
ANSI B16.47 Series A
Class 150 Flanges

Thickness Drilling Weight

Nom.
Weld OD Dia at Dia Bolt Dia # Weld
Pipe OD Blind Bore LTH Blind
Neck RF Base Bevel Circle Holes Holes Neck
Size
O C C R X B Y A
26 34.25 2.69 2.69 29.50 26.62 4.75 26.00 31.75 1.38 24.00 300 702
28 36.50 2.81 2.81 31.50 28.62 4.94 28.00 34.00 1.38 28.00 345 833
30 38.75 2.94 2.94 33.75 30.75 5.38 30.00 36.00 1.38 28.00 400 982
by purchaser.

32 41.75 3.19 3.19 36.00 32.75 5.69 32.00 38.50 1.62 28.00 505 1237
34 43.75 3.25 3.25 38.00 34.75 5.88 34.00 40.50 1.62 32.00 540 1384
36 46.00 3.56 3.56 40.25 36.75 6.19 36.00 42.75 1.62 32.00 640 1676
38 48.75 3.44 3.44 42.25 39.00 6.19 38.00 45.25 1.62 32.00 720 1819
40 50.75 3.56 3.56 44.25 41.00 6.44 40.00 47.25 1.62 36.00 775 2040
42 53.00 3.81 3.81 47.00 43.00 6.75 42.00 49.50 1.62 36.00 890 2381
To be specified

44 55.25 4.00 4.00 49.00 45.00 7.00 44.00 51.75 1.62 40.00 990 2717
46 57.25 4.06 4.06 51.00 47.12 7.31 46.00 53.75 1.62 40.00 1060 2961
48 59.50 4.25 4.25 53.50 49.12 7.56 48.00 56.00 1.62 44.00 1185 3348
50 61.75 4.38 4.38 55.50 51.25 8.00 50.00 58.25 1.88 44.00 1270 3716
52 64.00 4.56 4.56 57.50 53.25 8.25 52.00 60.50 1.88 44.00 1410 4156
54 66.25 4.75 4.75 59.50 55.25 8.50 54.00 62.75 1.88 44.00 1585 4639
56 68.75 4.88 4.88 62.00 57.38 9.00 56.00 65.00 1.88 48.00 1760 5132
58 71.00 5.06 5.06 64.00 59.38 9.25 58.00 67.25 1.88 48.00 1915 5675
60 73.00 5.19 5.19 66.00 61.38 9.44 60.00 69.25 1.88 52.00 2045 6154
Dimensions in inches. Weight in pounds.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series A
Class 300 Flanges

Weld Neck Flange Blind Flange

Thickness Drilling Weight

Nom.
Weld OD Dia at Dia Bolt Dia # Weld
Pipe OD Blind Bore LTH Blind
Neck RF Base Bevel Circle Holes Holes Neck
Size
O C C R X B Y A
26 38.25 3.12 3.31 29.50 28.38 7.25 26.00 34.50 1.75 28.00 605 1078
28 40.75 3.38 3.56 31.50 30.50 7.75 28.00 37.00 1.75 28.00 745 1315
30 43.00 3.62 3.75 33.75 32.56 8.25 30.00 39.25 1.88 28.00 870 1543
32 45.25 3.88 3.94 36.00 34.69 8.75 32.00 41.50 2.00 28.00 1005 1795
by purchaser.

34 47.50 4.00 4.12 38.00 36.88 9.12 34.00 43.50 2.00 28.00 1145 2068
36 50.00 4.12 4.38 40.25 39.00 9.50 36.00 46.00 2.12 32.00 1275 2436
38 46.00 4.25 4.25 40.50 39.12 7.12 38.00 43.00 1.62 32.00 695 2001
40 48.75 4.50 4.50 42.75 41.25 7.62 40.00 45.50 1.75 32.00 840 2380
42 50.75 4.69 4.69 44.75 43.25 7.88 42.00 47.50 1.75 32.00 950 2688
To be specified

44 53.25 4.88 4.88 47.00 45.25 8.12 44.00 49.75 1.88 32.00 1055 3079
46 55.75 5.06 5.06 49.00 47.38 8.50 46.00 52.00 2.00 28.00 1235 3499
48 57.75 5.25 5.25 51.25 49.38 8.81 48.00 54.00 2.00 32.00 1380 3896
50 60.25 5.50 5.50 53.50 51.38 9.12 50.00 56.25 2.12 32.00 1530 4442
52 62.25 5.69 5.69 55.50 53.38 9.38 52.00 58.25 2.12 32.00 1660 4906
54 65.25 6.00 6.00 57.75 55.50 9.94 54.00 61.00 2.38 28.00 2050 5684
56 67.25 6.06 6.06 59.75 57.62 10.25 56.00 63.00 2.38 28.00 2155 6098
58 69.25 6.25 6.25 62.00 59.62 10.50 58.00 65.00 2.38 32.00 2270 6669
60 71.25 6.44 6.44 64.00 61.62 10.75 60.00 67.00 2.38 32.00 2470 7274
Dimensions in inches. Weights in pounds.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series A
Class 400 Flanges

Weld Neck Flange Blind Flange

Thickness Drilling Weight

Nom.
Weld Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Dia at Base Blind
Neck Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 38.25 3.50 3.88 7.62 28.62 26.00 29.50 34.50 28.00 1.88 650 1263
28 40.75 3.75 4.12 8.12 30.81 28.00 31.50 37.00 28.00 2.00 785 1522
30 43.00 4.00 4.38 8.62 32.94 30.00 33.75 39.25 28.00 2.12 905 1802
32 45.25 4.25 4.56 9.12 35.00 32.00 36.00 41.50 28.00 2.12 1065 2077
34 47.50 4.38 4.81 9.50 37.19 34.00 38.00 43.50 28.00 2.12 1200 2415
36 50.00 4.50 5.06 9.88 39.38 36.00 40.25 46.00 32.00 2.12 1340 2815
38 47.50 4.88 4.88 8.12 39.50 38.00 40.75 44.00 32.00 1.88 935 2450
40 50.00 5.12 5.12 8.50 41.50 40.00 43.00 46.25 32.00 2.00 1090 2848
42 52.00 5.25 5.25 8.81 43.62 42.00 45.00 48.25 32.00 2.00 1190 3159
44 54.50 5.50 5.50 9.18 45.62 44.00 47.25 50.50 32.00 2.12 1375 3635
46 56.75 5.75 5.75 9.62 47.75 46.00 49.50 52.75 36.00 2.12 1525 4120
48 59.50 6.00 6.00 10.12 49.88 48.00 51.50 55.25 28.00 2.38 1790 4726
50 61.75 6.19 6.25 10.56 52.00 50.00 53.62 57.50 32.00 2.38 1950 5303
52 63.75 6.38 6.44 10.88 54.00 52.00 55.62 59.50 32.00 2.38 2125 5823
54 67.00 6.69 6.75 11.38 56.12 54.00 57.88 62.25 28.00 2.62 2565 6742
56 69.00 6.88 6.94 11.75 58.25 56.00 60.12 64.25 32.00 2.62 2710 7352
58 71.00 7.00 7.12 12.06 60.25 58.00 62.12 66.25 32.00 2.62 3230 7986
60 74.25 7.31 7.44 12.56 62.38 60.00 64.38 69.00 32.00 2.88 3820 9126
Dimensions in inches. Weights in pounds.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series A
Class 600 Flanges

Weld Neck Flange Blind Flange

Thickness Drilling Weight

Nom.
Weld Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Dia at Base Blind
Neck Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 40.00 4.25 4.94 8.75 29.44 26.00 29.50 36.00 28.00 2.00 940 1759
28 42.25 4.38 5.19 9.25 31.62 28.00 31.50 38.00 28.00 2.12 1060 2061
30 44.50 4.50 5.50 9.75 33.94 30.00 33.75 40.25 28.00 2.12 1210 2423
32 47.00 4.62 5.81 10.25 36.12 32.00 36.00 42.50 28.00 2.38 1375 2856
34 49.00 4.75 6.06 10.62 38.31 34.00 38.00 44.50 28.00 2.38 1540 3237
36 51.75 4.88 6.38 11.12 40.62 36.00 40.25 47.00 28.00 2.62 1705 3802
38 50.00 6.00 6.12 10.00 40.25 38.00 41.50 45.75 28.00 2.38 1470 3404
40 52.00 6.25 6.38 10.38 42.25 40.00 43.75 47.75 32.00 2.38 1630 3838
42 55.25 6.62 6.75 11.00 44.38 42.00 46.00 50.50 28.00 2.62 2030 4585
44 57.25 6.81 7.00 11.38 46.50 44.00 48.25 52.50 32.00 2.62 2160 5105
46 59.50 7.06 7.31 11.81 48.62 46.00 50.25 54.75 32.00 2.62 2410 5758
48 62.75 7.44 7.69 12.44 50.75 48.00 52.50 57.50 32.00 2.88 2855 6737
50 65.75 7.75 8.00 12.94 52.88 50.00 54.50 60.00 28.00 3.12 3330 7695
52 67.75 8.00 8.25 13.25 54.88 52.00 56.50 62.00 32.00 3.12 3560 8426
54 70.00 8.25 8.56 13.75 57.00 54.00 58.75 64.25 32.00 3.12 3920 9333
56 73.00 8.56 8.88 14.25 59.12 56.00 60.75 66.75 32.00 3.38 4280 10529
58 75.00 8.75 9.12 14.56 61.12 58.00 63.00 68.75 32.00 3.38 4640 11414
60 78.50 9.19 9.56 15.31 63.38 60.00 65.25 71.75 28.00 3.62 5000 13108
Dimensions in inches. Weights in pounds.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series A
Class 900 Flanges

Weld Neck Flange Blind Flange

Thickness Drilling Weight

Nom.
Weld Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Dia at Base Blind
Neck Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 42.75 5.50 6.31 11.25 30.50 26.00 29.50 37.50 20.00 2.88 1,525 2,566
28 46.00 5.62 6.75 11.75 32.75 28.00 31.50 40.25 20.00 3.12 1,810 3,178
30 48.50 5.88 7.18 12.25 35.00 30.00 33.75 42.75 20.00 3.12 2,120 3,758
32 51.75 6.25 7.62 13.00 37.25 32.00 36.00 45.50 20.00 3.38 2,545 4,541
34 55.00 6.50 8.06 13.75 39.62 34.00 38.00 48.25 20.00 3.62 2,970 5,425
36 57.50 6.75 8.44 14.25 41.88 36.00 40.25 50.75 20.00 3.62 3,395 6,209
38 57.50 7.50 8.50 13.88 42.25 38.00 43.25 50.75 20.00 3.62 3,385 6,253
40 59.50 7.75 8.81 14.31 44.38 40.00 45.75 52.75 24.00 3.62 3,620 6,940
42 61.50 8.12 9.12 14.62 46.31 42.00 47.75 54.75 24.00 3.62 3,960 7,675
44 64.88 8.44 9.56 15.38 48.62 44.00 50.00 57.62 24.00 3.88 4,300 8,954
46 68.25 8.88 10.06 16.18 50.88 46.00 52.50 60.50 24.00 4.12 4,640 10,426
48 70.25 9.19 10.38 16.50 52.88 48.00 54.50 62.50 24.00 4.12 4,980 11,398
Dimensions in inches. Weights in pounds.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 75 Flanges

Thickness Drilling Weight

Nom. Weld OD Dia at Dia Bolt Dia # Weld
Pipe OD Blind Bore LTH Blind
Neck RF Base Bevel Circle Holes Holes Neck
Size
O C C R X B Y A
26 30.00 1.31 1.31 27.75 26.62 2.31 26.06 28.50 0.75 36.00 80 255
28 32.00 1.31 1.31 29.75 28.62 2.44 28.06 30.50 0.75 40.00 85 290
30 34.00 1.31 1.31 31.75 30.62 2.56 30.06 32.50 0.75 44.00 90 330
by purchaser.

32 36.00 1.38 1.44 33.75 32.62 2.75 32.06 34.50 0.75 48.00 105 390
34 38.00 1.38 1.50 35.75 34.62 2.88 34.06 36.50 0.75 52.00 110 430
36 40.69 1.44 1.67 38.00 36.81 3.38 36.06 39.06 0.88 40.00 145 518
38 42.69 1.50 1.75 40.00 38.81 3.50 38.06 41.06 0.88 40.00 160 595
40 44.69 1.50 1.75 42.00 40.81 3.62 40.06 43.06 0.88 44.00 170 760
42 46.69 1.56 1.88 44.00 42.81 3.75 42.06 45.06 0.88 48.00 185 895
To be specified

44 49.25 1.69 1.94 46.25 44.88 4.12 44.06 47.38 1.00 36.00 230 1,065
46 51.25 1.75 2.00 48.25 46.88 4.25 46.06 49.38 1.00 40.00 245 1,185
48 53.25 1.81 2.12 50.25 48.88 4.38 48.06 51.38 1.00 44.00 270 1,315
50 55.25 1.88 2.18 52.25 50.94 4.56 50.06 53.38 1.00 44.00 290 1,505
52 57.38 1.88 2.25 54.25 52.94 4.75 52.06 55.50 1.00 48.00 310 1,665
54 59.38 1.94 2.38 56.25 55.00 4.94 54.06 57.50 1.00 48.00 340 1,840
56 62.00 2.00 2.44 58.50 57.12 5.31 56.06 59.88 1.12 40.00 400 2,110
58 64.00 2.06 2.50 60.50 59.12 5.44 58.06 61.88 1.12 44.00 430 2,300
60 66.00 2.19 2.62 62.50 61.12 5.69 60.06 63.88 1.12 44.00 475 2,500
Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 150 Flanges

ANSI B16.47 Series B Class 150 Flanges

Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.

Thickness Drilling Weight

Nom.
Weld OD Dia at Dia
Pipe OD Blind Bore LTH
Neck RF Base Bevel Bolt Dia # Weld
Blind
Size Circle Holes Holes Neck
O C C R X B Y A
26 30.94 1.62 1.75 28.00 26.94 3.50 26.06 29.31 0.88 36.00 120 373
28 32.94 1.75 1.88 30.00 28.94 3.75 28.06 31.31 0.88 40.00 140 454
30 34.94 1.75 2.00 32.00 31.00 3.94 30.06 33.31 0.88 44.00 150 543
by purchaser.

32 37.06 1.81 2.12 34.00 33.06 4.25 32.06 35.44 0.88 48.00 170 648
34 39.56 1.94 2.25 36.25 35.12 4.34 34.06 37.69 1.00 40.00 210 783
36 41.62 2.06 2.31 38.25 37.19 4.62 36.06 39.75 1.00 44.00 240 890
38 44.25 2.12 2.50 40.25 39.25 4.88 38.12 42.12 1.12 40.00 290 1,089
40 46.25 2.19 2.62 42.50 41.31 5.06 40.12 44.12 1.12 44.00 310 1,247
42 48.25 2.31 2.69 44.50 43.38 5.25 42.12 46.12 1.12 48.00 345 1,393
To be specified

44 50.25 2.38 2.81 46.50 45.38 5.38 44.12 48.12 1.12 52.00 370 1,579
46 52.81 2.44 2.94 48.62 47.44 5.69 46.12 50.56 1.25 40.00 435 1,824
48 54.81 2.56 3.06 50.75 49.50 5.88 48.12 52.56 1.25 44.00 480 2,045
50 56.81 2.69 3.18 52.75 51.50 6.06 50.12 54.56 1.25 48.00 520 2,284
52 58.81 2.75 3.31 54.75 53.56 6.19 52.12 56.56 1.25 52.00 550 2,547
54 61.00 2.81 3.44 56.75 55.62 6.38 54.12 58.75 1.25 56.00 620 2,848
56 63.00 2.88 3.56 58.75 57.69 6.56 56.12 60.75 1.25 60.00 650 3,144
58 65.94 2.94 3.68 60.75 59.69 6.88 58.12 63.44 1.38 48.00 780 3,560
60 67.94 3.00 3.81 63.00 61.81 7.06 60.12 65.44 1.38 52.00 850 3,913
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 300 Flanges

Thickness Drilling Weight

Nom. Weld OD Dia at Dia Bolt Dia # Weld
Pipe OD Blind Bore LTH Blind
Neck RF Base Bevel Circle Holes Holes Neck
Size
O C C R X B Y A
26 34.12 3.50 3.50 29.00 27.62 5.69 26.19 31.62 1.38 32.00 400 907
28 36.25 3.50 3.50 31.00 29.75 5.88 28.19 33.75 1.38 36.00 450 1,023
30 39.00 3.69 3.69 33.25 32.00 6.22 30.25 36.25 1.50 36.00 550 1,249
by purchaser.

32 41.50 4.06 4.06 35.50 34.00 6.62 32.25 38.50 1.62 32.00 685 1,556
34 43.62 4.06 4.06 37.50 36.12 6.81 34.25 40.62 1.62 36.00 750 1,719
36 46.12 4.06 4.06 39.75 38.00 7.12 36.25 42.88 1.75 32.00 840 1,921
38 48.12 4.38 4.38 41.75 40.00 7.56 38.25 44.88 1.75 36.00 915 2,257
40 50.12 4.56 4.56 43.88 42.00 7.81 40.25 46.88 1.75 40.00 990 2,549
42 52.50 4.69 4.69 46.00 44.00 8.06 42.31 49.00 1.88 36.00 1,135 2,876
To be specified

44 54.50 5.00 5.00 48.00 46.19 8.44 44.31 51.00 1.88 40.00 1,235 3,304
46 57.50 5.06 5.12 50.00 48.38 8.75 46.31 53.75 2.00 36.00 1,470 3,766
48 59.50 5.06 5.31 52.25 50.31 8.81 48.31 55.75 2.00 40.00 1,575 4,183
50 61.50 5.44 5.50 54.25 52.38 9.25 50.31 57.75 2.00 44.00 1,710 4,629
52 63.50 5.62 5.68 56.25 54.44 9.56 52.31 59.75 2.00 48.00 1,840 5,096
54 65.88 5.38 5.88 58.25 56.50 9.44 54.31 62.12 2.00 48.00 1,980 5,678
56 69.50 6.06 6.18 60.50 58.81 10.56 56.31 65.00 2.38 36.00 2,595 6,642
58 71.94 6.06 6.38 62.75 60.94 10.81 58.31 67.44 2.38 40.00 2,770 7,347
60 73.94 5.94 6.56 65.00 62.94 10.69 60.31 69.44 2.38 40.00 2,870 7,980
Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 400 Flanges

Thickness Drilling Weight

Nom.
Weld Dia at Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Blind
Neck Base Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 33.50 3.50 3.50 5.88 27.12 26.00 28.00 30.75 28.00 1.50 360 874
28 36.00 3.75 3.75 6.25 29.12 28.00 30.00 33.00 24.00 1.62 450 1,081
30 38.25 4.00 4.00 6.69 31.25 30.00 32.25 35.25 28.00 1.62 530 1,302
32 40.75 4.25 4.25 7.06 33.25 32.00 34.38 37.50 28.00 1.75 635 1,570
34 42.75 4.38 4.38 7.38 35.38 34.00 36.50 39.50 32.00 1.75 690 1,781
36 45.50 4.69 4.69 7.88 37.50 36.00 38.62 42.00 28.00 1.88 855 2,160
38 47.50 4.88 4.88 8.12 39.50 38.00 40.75 44.00 32.00 1.88 935 2,450
40 50.00 5.12 5.12 8.50 41.50 40.00 43.00 46.25 32.00 2.00 1,090 2,848
42 52.00 5.25 5.25 8.81 43.62 42.00 45.00 48.25 32.00 2.00 1,190 3,159
44 54.50 5.50 5.50 9.18 45.62 44.00 47.25 50.50 32.00 2.12 1,375 3,635
46 56.75 5.75 5.75 9.62 47.75 46.00 49.50 52.75 36.00 2.12 1,525 4,120
48 59.50 6.00 6.00 10.12 49.88 48.00 51.50 55.25 28.00 2.38 1,790 4,726
50 61.75 6.19 6.25 10.56 52.00 50.00 53.62 57.50 32.00 2.38 1,950 5,303
52 63.75 6.38 6.44 10.88 54.00 52.00 55.62 59.50 32.00 2.38 2,125 5,823
54 67.00 6.69 6.75 11.38 56.12 54.00 57.88 62.25 28.00 2.62 2,565 6,742
56 69.00 6.88 6.94 11.75 58.25 56.00 60.12 64.25 32.00 2.62 2,710 7,352
58 71.00 7.00 7.12 12.06 60.25 58.00 62.12 66.25 32.00 2.62 3,230 7,986
60 74.25 7.31 7.44 12.56 62.38 60.00 64.38 69.00 32.00 2.88 3,820 9,126
Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 600 Flanges

Thickness Drilling Weight

Nom.
Weld Dia at Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Blind
Neck Base Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 35.00 4.38 4.38 7.12 27.50 26.00 28.62 31.75 28.00 1.75 550 1,194
28 37.50 4.56 4.56 7.50 29.62 28.00 30.88 34.00 28.00 1.88 650 1,427
30 40.25 4.94 5.00 8.06 31.75 30.00 33.12 36.50 28.00 2.00 810 1,802
32 42.75 5.12 5.31 8.50 33.88 32.00 35.25 38.75 28.00 2.12 950 2,159
34 45.75 5.56 5.68 9.19 36.00 34.00 37.50 41.50 24.00 2.38 1,205 2,645
36 47.75 5.75 5.94 9.56 38.12 36.00 39.75 43.50 28.00 2.38 1,340 3,013
38 50.00 6.00 6.12 10.00 40.25 38.00 41.50 45.75 28.00 2.38 1,470 3,404
40 52.00 6.25 6.38 10.38 42.25 40.00 43.75 47.75 32.00 2.38 1,630 3,838
42 55.25 6.62 6.75 11.00 44.38 42.00 46.00 50.50 28.00 2.62 2,030 4,585
44 57.25 6.81 7.00 11.38 46.50 44.00 48.25 52.50 32.00 2.62 2,160 5,105
46 59.50 7.06 7.31 11.81 48.62 46.00 50.25 54.75 32.00 2.62 2,410 5,758
48 62.75 7.44 7.69 12.44 50.75 48.00 52.50 57.50 32.00 2.88 2,855 6,737
50 65.75 7.75 8.00 12.94 52.88 50.00 54.50 60.00 28.00 3.12 3,330 7,695
52 67.75 8.00 8.25 13.25 54.88 52.00 56.50 62.00 32.00 3.12 3,560 8,426
54 70.00 8.25 8.56 13.75 57.00 54.00 58.75 64.25 32.00 3.12 3,920 9,333
56 73.00 8.56 8.88 14.25 59.12 56.00 60.75 66.75 32.00 3.38 4,280 10,529
58 75.00 8.75 9.12 14.56 61.12 58.00 63.00 68.75 32.00 3.38 4,640 11,414
60 78.50 9.19 9.56 15.31 63.38 60.00 65.25 71.75 28.00 3.62 5,000 13,108
Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.
 STAINLESS STEEL FLANGES
ANSI B16.47 Series B
Class 900 Flanges

Thickness Drilling Weight

Nom.
Weld Dia at Dia OD Bolt # Dia Weld
Pipe OD Blind LTH Blind
Neck Base Bevel RF Circle Holes Holes Neck
Size
O C C Y X A R
26 40.25 5.31 6.06 10.19 29.25 26.00 30.00 35.50 20.00 2.62 1,050 2,184
28 43.50 5.81 6.56 10.88 31.38 28.00 32.25 38.25 20.00 2.88 1,520 2,762
30 46.50 6.12 6.93 11.38 33.50 30.00 34.50 40.75 20.00 3.12 1,820 3,334
32 48.75 6.31 7.31 11.94 35.75 32.00 36.50 43.00 20.00 3.12 2,065 3,865
34 51.75 6.75 7.68 12.56 37.88 34.00 39.00 45.50 20.00 3.38 2,450 4,576
36 53.00 6.81 7.94 12.81 40.00 36.00 40.50 47.25 24.00 3.12 2,520 4,963
38 57.50 7.50 8.50 13.88 42.25 38.00 43.25 50.75 20.00 3.62 3,385 6,253
40 59.50 7.75 8.81 14.31 44.38 40.00 45.75 52.75 24.00 3.62 3,620 6,940
42 61.50 8.12 9.12 14.62 46.31 42.00 47.75 54.75 24.00 3.62 3,960 7,675
44 64.88 8.44 9.56 15.38 48.62 44.00 50.00 57.62 24.00 3.88 4,300 8,954
46 68.25 8.88 10.06 16.18 50.88 46.00 52.50 60.50 24.00 4.12 4,640 10,426
48 70.25 9.19 10.38 16.50 52.88 48.00 54.50 62.50 24.00 4.12 4,980 11,398
Dimensions in inches.
Note: Larger sizes as well as intermediate sizes can be furnished.