Renovation & interior fitout at CGHS MCTC office on the 2nd floor,

South market shopping complex, East Kidwai Nagar, New

Delhi-110023
SUMMARY
Cost of Non DSR
S NO DESCRIPTION Cost of DSR Items
Items
1 CIVIL WORKS 5,803,051.0 12,990,961.0

2 SANITARY / PLUMBING WORKS 746,727.4 3,313,750.0

3 ELECTRICAL WORKS 2,986,504.0 3,622,425.0

4 HVAC WORKS 3,468,473.5 1,410,143.0

5 DATA & VOICE 313,500.0 2,138,224.0

6 CCTV WORKS 0.0 263,533.0

7 LIGHTING 0.0 1,308,030.0

8 FIRE ALARM & PA SYSTEM 1,260,056.0 329,460.0

9 FIRE FIGHTING SYSTEM 0.0 592,328.0

10 AV and VC WORK 0.0 8,824,666.5

11 MODULAR & LOOSE FURNITURE 0.0 6,598,207.0

TOTAL COST 14,578,312.0 41,391,727.5

Amount Inclusive GST (Add GST multiplying factor @ 1.0633 on DSR items ) 15501119.11 41391727.48
Total ₹ 56,892,846.00
Digitally signed by AMIT
SINGH
1 Date: 2024.08.27 16:02:05 IST
 SCHEDULE OF QUANTITIES CIVIL
QUANTIT AMOUNT AMOUNT
S.NO. DSR / MR DESCRIPTION UNIT RATE
Y DSR ITEM NON DSR ITEM
1 CONCRETE WORK
DSR 2021 VOL-
Providing and laying in position cement concrete of specified grade exluding the
1.01 4.1 cost of centring and shuttering-all work upto plinth level.

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 103.00 Cum 6,326.05 651,583.15

2 BRICK WORK
DSR 2021 VOL-
1 BRICK WALL: Half brick masonry with common burnt clay F.P.S. (non modular)
2.01 6.13 bricks of class designation 7.5 in superstructure above plinth level up to floor
V level.
6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 60 Sqm 1,018.05 61,083.00
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third
2.02 6.15 60 Sqm 86.45 5,187.00
course of half brick masonry.
Brick work with common burnt clay F.P.S. (non modular) bricks of class
6.4 designation 7.5 in superstructure above plinth level up to floor V level in
all shapes and sizes in :

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 10 Cum 8,512.10 85,121.00

AAC WALL (150 MM): Providing and laying autoclaved aerated cement blocks
masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above
plinth level up to floor V level with RCC band at sill level and lintel level with
2.03 6.47 approved block laying polymer modified adhesive mortar all complete as per 30 Cum 6,994.15 209,824.50
direction of Engineer-in-Charge. (The payment of RCC band and reinforcement
shall be made for seperately).
AAC BLOCK FILLING: Providing and Laying of AAC Block Filling in the Slab
Sunk or Raised Areas as a Back fill or platform. Laying should be done in layers
with pounding done at every level to ensure a proper cavity free installation
2.04 MR 10 Cum 5,000.00 50,000.00
without disturbing any existing services in the area. Cost to also include
haunching for plumbing pipes.

3 FINISHING WORK
DSR 2021 VOL-
3.01 13.4 CEMENT PLASTER: 12 mm cement plaster of mix :

13.4.1 1:4 (1 cement: 4 coarse sand) 280 Sqm 307.25 86,030.00

DSR 2021 VOL-
PLASTIC PAINT: Wall painting with acrylic emulsion paint of approved brand and
3.02 13.60 manufacture to give an even shade :

13.60.1 Two or more coats on new work 3360 Sqm 137.85 463,176.00
DSR 2021 VOL-
Painting with synthetic enamel paint of approved brand and manufacture to give
3.03 13.61 an even shade :
Digitally signed by AMIT
SINGH
13.61.1 Two or more coats on new work 20 Sqm 131.45 2,629.00
Date: 2024.08.27 16:02:05 IST
1
 DSR 2021 VOL-
PUTTY WORKS ON SLAB: Providing and applying plaster of paris putty of 2 mm
3.04 13.26 thickness over plastered surface to prepare the surface even and smooth 520 Sqm 214.30 111,436.00
complete.

DSR 2021 VOL-

2
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622
(thickness to be specified by the manufacturer), of approved make, in all colours,
shades except burgundy, bottle green, black of any size as approved by Engineer-
in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement
3.06 8.31 mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 342 Sqm 1,063.45 363,699.90
3.3kg per sqm, including pointing in white cement mixed with pigment of matching
shade complete.

DECORATIVE DADO WALL TILES ABOVE COUNTER: P/F High Quality

Ceramic / Subway/ Pattern Tiles as Selected by Engineer in charge and
installation in Herring bone type / random etc to be done to bring the surface
plumb and minimize cut tiles/ joints. Tile joints to be finished ist up to 4mm Width
3.07 MR and Full Depth installed with removable spacers and installation in Design, Laying 7 Sqm 1,064.00 7,448.00
Pattern and Colour as approved by the Engineer in charge. Quoted item Rate
shall include Wastages as per installation methodology.

WASHROOM ACCENT TILES ON WALLS: Providing and fixing Ist quality

ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except burgundy, bottle
green, black of any size as approved by Engineer-in-Charge, in skirting, risers of
3.08 MR steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 45 Sqm 2,200.00 99,000.00
coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade complete.

Cutting core of required size i.e 100mm, 150mm,300mm of required depth upto
3.09 MR 450mm complete in all respect 6 Nos 1,500.00 9,000.00

Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay
stone flooring laid in required pattern in linear portion of the building all complete
as per architectural drawings, with 18 mm thick stone slab laid over 20 mm
(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and
3.10 11.51
jointed with white cement slurry @ 4.4 kg/sqm including pointing with white
cement slurry admixed with pigment to match the marble shade including rubbing,
curing and polishing etc. all complete as specified and as directed by the
Engineer-in-Charge.
11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 50 sq m 6095.50 304775

4 WATERPROOFING WORK
DSR 2021 VOL-

Digitally signed by AMIT

SINGH
2 Date: 2024.08.27 16:02:05 IST
 WATER PROOFING: Providing and laying water proofing treatment to vertical
and horizontal surfaces of depressed portions of W.C., kitchen and the like
consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with
water proofing compound conforming to IS 2645 in recommended proportions
including rounding off junction of vertical and horizontal surface. (ii) IInd course of
20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing
4.01 22.3 compound in recommended proportion including rounding off junction of vertical 1250 Sqm 774.25 967,812.50
and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen
applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC
sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to
each other with bitumen @ 1.7 kg/sqm). Quantity is inclusive terrace floor.

DSR 2021 VOL-

Indian Patent Stone Flooring (IPS)
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate) finished with a floating coat of neat cement, including cement slurry,
4.02 11.3 but excluding the cost of nosing of steps etc. complete. 35 Sqm 545.00 19,075.00

11.3.1 40 mm thick with 20 mm nominal size stone aggregate

Structural steel work riveted, bolted or welded in built up sections, trusses and
5.03 10.2 framed work, including cutting, hoisting, fixing in position and applying a priming 1050 kg 111.95 117,547.50
coat of approved steel primer all complete

DSR 2021 VOL-

Providing wood work in frames of doors, windows, clerestory windows and other
frames, wrought framed and fixed in position with hold fast lugs or with dash
fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for
5.04 9.1
separately).

9.1.1 Second class teak wood 1 Cum 131,576.95 131,576.95

DSR 2021 VOL-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part
I) non-decorative type, core of block board construction with frame of 1st class
5.05 9.21 hard wood and well matched commercial 3 ply veneering with vertical grains or
cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary 19.20 Sqm 2,015.75 38,702.40

DSR 2021 VOL-

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum
5.06 9.23 depth on all edges of flush door shutters (over all area of door shutter to be 19.20 Sqm 401.40 7,706.88
measured).
Providing and fixing Stainless steel satin finish SS 304 grade Tower Bolts SS
screws for wooden doors of approved make and model all complete as per the
5.07 MR directions of Engineer-in-charge 8 Each 215.00 1,720.00
250x10mm
Digitally signed by AMIT
SINGH
3 Date: 2024.08.27 16:02:05 IST
 Providing and fixing Stainless steel satin finish SS 304 grade D type Handles with
SS screws for wooden doors of approved make and model all complete as per
5.08 MR the directions of Engineer-in-charge 32 set 1,256.00 40,192.00
300mm

DSR 2021 VOL-

Providing and fixing aluminium die cast body tubular type universal hydraulic door
closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight
5.09 9.83 upto 35 kg and door width upto 700 mm), with necessary accessories and screws 8 Each 1,025.65 8,205.20
etc. complete.
DSR 2021 VOL-
1
Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10
mm diameter bolts, nuts and wooden plugs and embedding in cement concrete
5.10 9.53 block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone 88 Each 194.35 17,102.80
aggregate 20mm nominal size).

FRAMED SINGLE GLAZED ALUMINIUM PARTITIONS: Supply & Installation of

Full Height demountable Anodised Aluminium Single Glazed Series Straight
Partitions systems of Matt anodized finish of 100x18/100x25/105x50mm cross
section and 'T' Section, corner Section & 'I 'between glass to glass joint of
proprietary make formed out of the following components as per the detail
drawing / design .
Framing: Proprietary anodized aluminium profile using sections on all four sides
for the partition as per manufacturer specifications from FFL up to 2700 mm.
Glazing: 10mm thick toughened Glass for partition system with joint sealed using
3M make clear & non staining double sided tape for glass to glass joint with
5.11 MR Frosted Translucent glass film, cast PVC, self-adhesive vinyl, special CRYSTAL- 110 Sqm 5,500.00 605,000.00
effect film to reproduce Sand-blasting effect on glass with customised designs,
thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having
minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C) . All
exposed edges of the glass shall be machine polished. Quoted rate shall include
packing/liner for all partitions as floor level. Capping & gaskets shall be of
EPDM.including fasteners making hole in walls in floors, making door provision.

DAR 2021 VOL-

2
Providing & Fixing Frosted Translucent glass film, cast PVC, self-adhesive vinyl,
special CRYSTAL-effect film to reproduce Sand-blasting effect on glass with
customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil
(0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6
kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7
5.12 MR kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to 110 Sqm 1,400.00 154,000.00
direct sunlight) to 15yrs (indoors) must be endorsed by 3M India Limited Engineer
in chargeural Market Department. Contractors payment wouldn't be released until
& unless he/she produces orginal warranty certificate from the manufacturer.

Digitally signed by AMIT

SINGH
4 Date: 2024.08.27 16:02:05 IST
 SINGLE LEAF ALUMINIUM FRAME & STILE GLASS DOOR: P/F of Single
Glazed Door-Consisting of Single Shutter Anodized aluminium finish in 75x45 /
65 x40 mm as approved by Engineer in charge of system on all four sides using
in vertical, and in top of the door and on the bottom of the door for 10 mm thick
tempered glass insert with around beading, Door shutter to be fixed , 70mm EPC
with one side key and one side thumb turn, Door closer with hold open, floor
mounted door stopper and side / astragal drop seal for sound barrier. Door Frame
made put of horizontal member on top 36x100 / 50X100 mm and both vertical
member 36x100mm / 50x100 mm Along door jamb with schlegal door trim and
5.12 MR Hinges for 45mm Door as per manufacturers specification. The door frame
should be Compatible to hold the Single glazed aluminium style door shutter.
Cost to include overhead guide rail door closer with hold open , 9168483
Narrow stile mortise sash lock in Make as approved by Engineer in charge , 92
mm C/C x 35mm backset includes strike plate and screws, K35/K35, double
cylinder in 70mm length with 3keys and fixing screws in SNP finish.

Handle, lock , Door closer , hinges hardware included in the rate etc for complete
5.12(a) 19 Nos 29,500.00 560,500.00
door installation.

DOUBLE LEAF ALUMINIUM FRAME & STILE GLASS DOOR: P/F of Single
Glazed Door-Consisting of Double Shutters Anodized aluminium finish in 75x45
/ 65 x40 mm as approved by Engineer in charge of system on all four sides using
in vertical, and in top of the door and on the bottom of the door for 10mm thick
tempered glass insert with around beading, Door shutter to be fixed with Narrow
stile , 70mm EPC with one side key and one side thumb turn, Door closer with
hold open, floor mounted door stopper and side / astragal drop seal for sound
barrier. Door Frame made put of horizontal member on top 36x100 / 50X100
5.13 MR 2 Nos 49,500.00 99,000.00
mm and both vertical member 36x100mm / 50x100 mm Along door jamb with
schlegal door trim and Hinges for 45mm Door as per manufacturers
specification. The door frame should be Compatible to hold the Single glazed
aluminium style door shutter. Cost to include overhead guide rail door closer
with hold open 9168483 Narrow stile mortise sash lock ML NSL 92 , 92 mm C/C x
35mm backset includes strike plate and screws, EPC K35/K35, double cylinder in
70mm length with 3keys and fixing screws in SNP finish.Lever handle, lock , Door
closer , hinges hardware etc for complete door installation.

VERTICAL TUBE TRANSOM PANEL: P/F of Proprietary anodized aluminium

post profile integrated to framing system up to 2700 mm High as per sections of
Matt anodized finish of 200x100/40mm with specs and finish as specified as per
5.14 MR 5 Nos 29,500.00 147,500.00
Aluminium Glazing to be installed adjacent to doors having provision of Access
Control as per the Door Schedule of Engineer in charge. Finish & Colour as
approved by Engineer in charge.

Digitally signed by AMIT

SINGH
5 Date: 2024.08.27 16:02:05 IST
 SINGLE LEAF FIRE RATED DOORS SOLID CORE: Supply & installation of
approved make 40mm thick light weight asbestos free Single Leaf fire proof doors
of 120 minutes fire rating duly tested for Integrity & Insulation Criteria confirming
to IS: 3614 Part 2 and BS: 476 part 22 at Fire Research Laboratory Central
Building Research Institute Roorkee with standard heating conditions as specified
in IS: 3809 - 1979 and BS: 476 part 20 & 22 1987 to achieve the required integrity
& insulation (i.e. to restrict the heat radiation, temperature rise on the non fire side
to the maximum of 140 degree Centigrade above the ambient temperature on the
unexposed surface of the shutter) complete in all respect as per detail.Door
Frame: Formed out of 1.6mm thick Galvanized steel sheet pressed form to
double rebate profile of size 100mm x 65mm as per IS277. Shutter: Formed out
of 2 NUMBER. 1.6mm thick Galvanized steel sheet with infill of fire rated Acrylic
Sealant and non-combustible core (Rock wool 96Kg/M³) bonded to both faces of
sheet with lock seam joints at stile edges and internal reinforcement at top,
bottom and stile edges for fire rating. Finish : Door frames and shutter shall be Nos 65,000.00 195,000.00
5.15 MR 3
finished with primer coating, stoved zinc phosphate primer (35 micron DFT) and
thermosetting Polyurethane aliphtic grade paint (35 micron DFT) of approved
colour. Vision Panel : 1 no. of size upto 450 mm. x 450mm. Vision panel formed
out of 6mm thick Pilkington Pyro shield of 120 minutes fire rated clear wired glass
with metal beading as per detail. Contractor to make provision for fixing of Access
Control System Device where ever required as per detail. Rate shall include for
supply and fix 3mm thick base plates, all joints of frames with provision for anchor
bolt fixing to wall/ RC surface, reinforcement pad for fixing of door closers, factory
finish, pre-punched cut outs to receive hardware's and iron mongery. Rate shall
also include for grouting the frame with cement slurry between Wall & Frame and
silicone sealant as per approval to the required thickness as per manufacturer’s
specifications. Cost to include 25/32 mm x 450/600 mm D Offset Handle /Panic
Bar as approved by Engineer in charge with facility for Access control integration
and pelmet arm Door Closer. All Hardware shall be as per Fire Norms and
approved Shop Dwgs by the Engineer in charge.

SHAFT SHUTTER: P/F 35 mm Thk 2 Hrs FR readymade shaft shutters with

frame mounted with 3" ball bearing hinge customised to cover the opening size
5.16 MR with L Key locking mechanism. The Frame and Shutter to be finished with Powder 5 Sqm 18000.00 90,000.00
Coated Finish on all surfaces as approved by the Engineer in charge. All
Hardware used to be 2 HR fire Rated.

5.17 9.133.2 Multipurpose cement board reinforced with suitable fibre cement screw.

9.133.2.1 8 mm thick cement fibre board as per IS : 14862 20 Sqm 1209.10 24,182.00
6 PARTITION WORK
DSR 2021 VOL-
1
Digitally signed by AMIT
SINGH
6 Date: 2024.08.27 16:02:05 IST
 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails,
including a coat of approved primer on one face, and fixed on wooden / steel
6.01 9.140 frame work, complete as per direction of Engineer-in- charge (Frame work shall
be paid for separately).

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type 50 Sqm 1,084.60 54,230.00
Providing and fixing metal system up to ceiling height, which includes frame work
made of special section power pressed/ roll form G.I. sheet with zinc coating of
120 GSM, consisting of U track 52mm wide having equal flanges of 30mm and
0.55mm thick (Base metal thickness) fastened to the floor slab and ceiling soffit
using rawl plugs with screw at 600mm centers, with first & last fixing point at not
greater than 50 mm from either end. C studs 50mm wide having one flange of
6.02 MR 100 Sqm 1,022.00 102,200.00
34mm, other flange 36mm, lip size 6 mm and 0.55mm thick installed
perpendicularly within the flanges of floor and ceiling channels located directly
opposite to each other at not more than 610mm centers. Maintain 5 to 10mm gap
between C Stud and web of U Track.

Providing and fixing of 4mm MDF sheet on existing plywood partition / panelling
with 4mm wide grooves in approved pattern complete in all respects with
6.03 MR adhesive and all accessories as required.The grooves to be finished using paint 30 Sqm 450.00 13,500.00
of approves shade.

DSR 2021 VOL-

6.04
1
Providing and fixing partition upto ceiling height consisting of G.I. frame and
required board, including providing and fixing of frame work made of special
section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both
side inclusive), consisting of floor and ceiling channel 50mm wide having equal
flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing
of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm
length or suitable anchor fastener or metal screws with nylon plugs and the studs
48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm
thick fixed vertically within flanges of floor and ceiling channel and placed at a
spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of
studs along both ends of partition fixed flush to wall with suitable anchor fastener
or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing
9.105 of boards to both side of frame work by 25 mm long dry wall screws on studs,
floor and ceiling channels at the spacing of 300 mm centre to centre. The boards
are to be fixed to the frame work with joints staggered to avoid through cracks,
M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm
each) to be provided at the horizontal joints of two boards, fixed to the studs using
metal to metal flat head screws, including jointing and finishing to a flush finish
with recommended jointing compound, jointing tape, angle beads at corners (25
mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board
as per manufacture's specification and direction of engineer in charge all
complete.

Digitally signed by AMIT

SINGH
7 Date: 2024.08.27 16:02:05 IST
 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass
Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board
6.05 9.105.1 with BIS certification marks) 18 Sqm 1,797.65 32,357.70

75mm overall thickness partition with 12.5 mm thick double skin tapered edged
plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS
6.06 9.105.2 113 Sqm 1,530.05 172,895.65
certification marks)

SINGLE GYPSUM EXTRA SKINNING: P/F Plain 12.5 mm One Side High density
6.07 MR Gypsum Board Skin with Taping and Jointing work 39 Sqm 1,200.00 46,800.00

7 FLOORING WORK
DSR 2021 VOL-
1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be
specified by the manufacturer) with water absorption less than 0.08% and
conforming to IS:15622, of approved brand & manufacturer, in all colours and
shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing
with grey cement slurry @3.3 kg/sqm including grouting the joints with white
7.01 11.41 cement and matching pigments etc. The tiles must be cut with the zero chipping
diamond cutter only . Laying of
tiles will be done with the notch trowel, plier, wedge, clips of required thickness,
leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.1.3 Double charge vitrified tile polished finish of size of Tile 600 x 1200 mm 400 Sqm 1,407.05 562,820.00
MOSAIC TILE: Providing and fixing made in India Glass mosaic tiles at Floor &
finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design ,
fixing in customize design as per direction of Engineer-in- Charge. The glass
mosaic tiles to be fixed on the wall surface with the help of approved Adhesive AD
7.02 MR HOC (2,7 kg) + Epoxy coloured grout FILLGEL PLUS UVR (3 kg) applied at the 200 Sqm 3,200.00 640,000.00
rate per sqm. The rate is inclusive of all operation, material and required pattern

Providing Supply and laying LVT flooring 5 mm thickness with 0.50 wear layer (
Luxury vinyl flooring of approved design & pattern as per engineer in charge
approval & instruction). Type of flooring: Vinyl synthetic floor covering,
heterogeneous with EPT Sheild (Anti Bacterial & anti Fungal) ,SGBP Certified
.Overall thickness:- EN ISO 24346: 5.0 mm. Thickness of wear layer :- ISO
24340: 0.50- 0.55mm. Abrasion Group: EN 660-2, Class T. Binder content wear
layer : EN ISO 10582 typer I (HPD certified). Level of use - EN ISO 10874 class
23/33/42. Dimensional stability :- ISO 23999<0.10% & Culing after exposure to
7.03 MR heat <1.0mm . Safety Creteria, Fire resistance EN 13501-I Bfl-s1 (Class A) Slip 200 Sqm 4,250.00 850,000.00
resistance: EN 13893 (DS), DIN 51130-R 10 Light Fastness :- ISO 105-B02>6
Performance Impact sound reduction :- EN ISO 10140-3 (9 dB), Resistance to
Chemicals :- ISO 26987 (No Damage ) Warm water :- under floor heating suitable
max.27 C Static Load Limit : ASTM F970 <0.005in @ 250psi min Formaldehyde
Group :- EN 717-1 (Ei0 VOC emissions:- IAC Gold Certified very low VOC of
approved quality complete as per Engineer in charge .

Digitally signed by AMIT

SINGH
8 Date: 2024.08.27 16:02:05 IST
 Providing and laying Carpet tiles of Yarn type Nylon (Nylon 6) only; Multi-Level
Pattern Loop, manufactured using 100% solution dyeing process, Tiles of size
61cms x 61cms equivalent as per direction of EIC and site requirement with
SSP® Soil Protection treatment ™ or equivalent containing properties of Stain
Repel, with Tile- 100% PVC Free/ 100% Bitumen Free/ 100% Recyclable -
backing system with recycled content, made from thermoplastic polyolefin
compound with reinforcing layer high-performance environments requiring
modular flooring, having tufted yarn weight of 542.5 gsm/sqm and average yarn
MR density of Minimum 6128 oz/cu. yd. or more, Nominal total thickness 5.84 mm 80 Sqm 3,500.00 280,000.00
minimum, Radiant Panel class 1rated ( ASTM E648), NBS smoke < 450, Pill
test -Passed, Anti Static Property less Than 3.5 kv, Texture Appearance
Retention Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes
(AATCC-174). CRI Green Label Plus is certified for indoor air quality, including
fixing/ installation with Low/ Zero VOC content Adhesive. Impact Sound (ISO
10140-3) 20 dB & Sound absorption (ISO 354)

Providing and fixing removable raised/false access flooring with system and its
components of approved make for different plenum height with possible height
adjustment upto 50 mm, comprising of modular load bearing floor panels
7.04 11.54 supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all
complete, as per the Engineer in chargel drawings, as specified and as directed
by Engineer-in-charge

a) Providing at required spacing to form modular framework, pedestals made out

of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on
to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the
pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI
fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the
stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in
position at the required level. The pedestals shall be fixed to the subfloor (base)
through base plate using epoxy based adhesive of approved make or the
machine screw with rawl plug.
(b) Stringers system in all steel construction hot dipped galvanized of rectangular
size 570x20x30x0.80mm thick having holes at both ends for securing the
stringers on to the pedestal head using fully threaded screws ensuring maximum
lateral stability in all directions, the grid formed by the pedestal and stringer
assembly shall receive the floor panel, this system shall provide adequate solid,
rigid support for access floor panel, the system shall provide a minimum clear
uninterrupted clearance between the bottom of the floor for electrical conduits and
wiring etc. all complete as per the Engineer in chargeural drawings, as specified
and as directed by the Engineer-in-charge.

Digitally signed by AMIT

SINGH
9 Date: 2024.08.27 16:02:05 IST
 (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade
Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access
Floor panel shall be steel welded construction with an enclosed bottom pan with
uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel
Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum
64 welds in each dome and 20 welds along each flange). The panel should be
Corroresist epoxy coated for lifetime rust protection and cavity formed by the top
and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core
mixed with lightweight foaming compound. The access floor shall be factory
finished with Anti-static High Pressure laminate with Non Warp technology upto
1mm thickness for superior adhesion and Surface flatness within 0.75mm.The
panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x
25mm without collapse in the centre of the panel which is placed on four steel
blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum
1250 kg/sqm and an impact load of 50kg all complete as per the approved
manufacturers specification and as per the direction of Engineer-in-charge. All
specification must be printed on the side of the panel to ensure the quality of the
product.

11.54.2 450 mm Finished Floor Height (FFH). 12 Sqm 5,407.15 64,885.80

ALUMINIUM SKIRTING: P/F High Grade Sand Blasted Finish Aluminium skirting
in colour and Finish as approved by Engineer in charge of easy stick type with all
aluminium trims and Aluminium champhered corners as per Engineer in charge’s
7.06 MR approval fixed as per detail and Engineer in charges instructions. Skirting to be 450.00 Rmt 500.00 225,000.00
affixed on to plastered/POP finished wall surface.

MR THROW RUGS: Providing and laying Rugs Broadlooms in Hand Tufted to

Customised design of approved size in locations as directed. The cost shall
7.07 include all adhesive necessary items required for installation. 25 Sqm 3,520.00 88,000.00

8 FALSE CEILING WORK

DSR 2021 VOL-
1 Providing and fixing false ceiling at all height including providing and fixing of
frame work made of special sections, power pressed from M.S. sheets and
galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277
and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of
27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling
with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of
cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts &
bolts of required size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to
8.01 12.45 which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered
flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall
be fixed in a direction perpendicular to G.I. intermediate channel with connecting
clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including
fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and
30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl
plugs
Digitally signed by AMIT
SINGH
10 Date: 2024.08.27 16:02:05 IST
 at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including
fixing of gypsum board to ceiling section and perimeter channel with the help of
dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing
to a flush finish of tapered and square edges of the board with recommended
jointing compound , jointing tapes , finishing with jointing compound in 3 layers
covering upto 150 mm on both sides of joint and two coats of primer suitable for
board, all as per manufacturer's specification and also including the cost of
making openings for light fittings, grills, diffusers, cutouts made with frame of
perimeter channels suitably fixed, all complete as per drawings, specification and
direction of the Engineer in Charge but excluding the cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I)
12.45.1 :2011 (Board with BIS certification marks) 750 Sqm 1,145.95 859,462.50

TRAP DOORS - HVAC UNIT: Providing and Fixing and Installation of Trap Door
made of 6mm thick wpc board , finisanhed with laminate/paint as per requirement
, including framworks, Single Leaf /Double leaf with all necessary hardwares as
8.02 MR per Interior Design and the direction of Engineer-in-charge 5 Sqm 1,249.00 6,245.00

ACCESS PANELS: P & F ready made acess panels in ceiling made of Metal and
HDMHR pane of Max size 600mm x 1200 mm in gypsum ceiling of manufacturer
supplied prefab recessed frame placed inside gypsum ceiling frame work which
is fixed to gypsum board on all sides with push pull mechanism, panel to be
8.03 MR cladded with matching paint/Finish of the surrounding ceiling Member, complete 2 Sqm 1,850.00 3,700.00
as per design & drawing & instructions of Engineer in charges.

METAL BAFFLE CEILING: Providing and fixing decorative ceiling system

manufactured from anodised /powder coated lightweight aluminium Baffles The
system comprises baffles upto 50 mm wide & height of the baffle shall be upto
150mm manufactured out of 0.50mm Thick GMS, installed at upto 150mm C/C
distance with Straight / Curved Edge profile. The profile if required by Engineer in
charge shall have perforation design as per patttern and dia approved by
Engineer in charge.The carrier rails run perpendicular to the baffles. Individual
baffle lengths between 300 and 2400 mm can be selected. Baffle ceiling are
supplied with the end cap matching the similar finish of baffle. Tolerances
according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015
approved by SIS. Substructure for Vertical baffle system consisting of
30X40X30X1.2mm Thick GMS C Channels installed perpendicularly to baffles at
1200 mm c/c. The C channels must be connected to one another with longitudinal
C channel connectors. The entire ceiling module shall be suspended with 6mm
8.06 MR diameter galvanized steel threaded rods from the true ceiling officially approved 100 Sqm 6,200.00 620,000.00

Digitally signed by AMIT

SINGH
11 Date: 2024.08.27 16:02:05 IST
8.06 MR diameter galvanized steel threaded rods from the true ceiling officially approved 100 Sqm 6,200.00 620,000.00
anchor fasteners maximum at 1200mm Centres as per the requirements of DIN
EN 13964 and the statics of the system. Ensure horizontal and flush alignment
during installation.
Finish: RAL 9016 white Finish or any other colour in solids or wood textured and
printed as per approval of the Engineer in charge.
Manufacturer shall have the fully automatic powder coating system with power
and free conveyorize 3mtr/minute capacity. Powder coating plant shall be
equipped with latest modern technology with fully automatic inline Pre-treatment
using nano technology, Inline automatic water Drying system after pre-
treatment.Installation to be done as per the manufacturers proprietary Specs
according the Ceiling Design of the Engineer in charge. Shop Drawing of
formation pattern to be furnished by contractor for approval of the Engineer in
charge.
PET FELT PANEL DESIGNER PARTITION: Providing and fixing factory finished
PET Array panels in total thickness of upto 27 mm and 200 Kg per Cum in design
and CNC cut profile in shape as size with up to 8 mm Thk MDF Skeleton if
required as per the instructions of the Engineer in charge .Cost to include
aluminium U channel hung from Existing Ceiling and Slab in Colour and Profile as
designed engineer in charge the choice of colours shall be as selected engineer
8.08 MR in charge and client. Hung directly from the structural soffit or from a primary 12 Sqm 3,500.00 42,000.00
angle section and restrained on floor. Clutch wire / M6 threaded rod or approved
hangers with suspension height void minimum 150 mm. Installation to be done as
per the manufacturers proprietary Specs according the Ceiling Design of the EICr.

TILE GRID CEILING - MINERAL FIBRE 600 X 600 MM (0.7 NRC): General
Notes :Providing and Fixing modular ceiling system consisting of Grid & Tile
System in 15 mm Tile Thk and NRC 0.7 and CAC of 33 DB with 20 mm Thicknes
Tegular Edge of size up to 600 x 600 Module with 15 mm Groove Silhouette
Microgrid Grid or equivalent with suggested generic specs as follows:
1. Tiles of , nominal size range or equivalent with Tegular edge.
2. Ceiling grid to be of hot dip galvanized steel system, power coated white finish,
including main runners, cross tees and wall angles. The tile shall be laid on profile
grid system with 15mm white flanges incorporating a 6mm central reveal in
white/black colour. Main Runners & Cross Tees to have mitred ends & “birds
mouth” notches to provide mitred cruciform junctions. The T Sections have a
galvanizing of 120 grams per M2 & passed through 500 hrs of Salt test.
8.09 MR 3. Main runners to be spaced at 1200mm centres, fixed to soffit by approved 500 Sqm 1,850.00 925,000.00
hangers at 1200 mm distance. First and last hangers should not be at a distance
of more than 450 mm from the adjacent wall. module to be formed by fixing 600
mm cross tee between centre of 1200 mm cross tees.

4.Wall angle to be secured to wall at 450mm centres. tile shall be laid on

reveal profile grid system with 15mm white flanges incorporating a 6mm central
reveal in white/black colour and with a web height of 45mm. Overall Light
Reflectance in the Range of 80 - 85 %. Overall system to be designed as per
manufacturer specs following ASTM C 635, 636 & 645 with proper lab certification
to be furnished.

Digitally signed by AMIT

SINGH
12 Date: 2024.08.27 16:02:05 IST
 LACQUERED GLASS CLADDING: P/F up to 6mm Thk Lacquered Glass on a
backing of Existing Partition and Panelling and faced front side with up to 6 mm
thick MDF and finished with 6mm Lacquered Glass Super White Colour or As
Approved by the Engineer in charge to make it flush in level with adjoining
surfaces. Cost to also include Neutral Silicon Adhesive or equivalent
9.01 MR 150 Sqm 4,200.00 630,000.00
manufacturer suggested adhesive as per approved Design make and edge
polishing. Item Billing shall be done on Installed area on site with wastage to be
included in the rates.

3D PET FELT ECHO PANEL WITH PRINTING: Providing and fixing factory
finished Smart PET panels in thickness up to 12 mm of 0.5 NRC in wave and
other 3D pattern as per design and embossing as per the instructions of the
Engineer in charge. Cost to include screen printing work and Provision for making
9.02 MR Champhered Edges and Grooves in different cuts like fishbone etc as per the 115 Sqm 4,250.00 488,750.00
instruction of the Engineer in charge. Installation to be done as per the
manufacturers proprietary Specs according the Design of the Engineer in charge.
Shop Drawing of pattern and panel joints to be furnished by contractor for
approval of the Engineer in charge.
DSR 2021 VOL-
1 Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain
9.03 a 8.29 lining with necessary screws, priming coat on unexposed surface etc., complete. 45 Sqm 1,549.45 69,725.25

9.03 b MR PU POLISH: PU polish in shade as per Engineer in charge’s approval. 45 Sqm 1,532.00 68,940.00
DSR 2021 VOL-
1 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain
in gloss / matt/ suede finish with high density protective surface layer and reverse
9.04 9.127 side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of
adhesive of approved quality.

9.127.2 1 mm thick 119 Sqm 764.00 90,916.00

PREMIUM TEXTURED VINYL WALL COVERINGS: P/F Decorative Vinyl
covering of upto 34 oz /Sq yd as Approved by Engineer in charge on Existing
Partition and Panelling finished with water resistant stain resistant vinyl
coverings Selection as per Engineer in charge’s approval. Wall /Ceiling Base to
be prepared by applying coat of cement primer scrapped and smoothened to
plumb level on backing panel of Gypsum/ MDF, intermediate grooves to be
9.05 MR finished with Paint. Including cost of providing grooves and/Wall with divisions in 200 Sqm 2,350.00 470,000.00
pane as per Engineer in charges approval. Cost to also include Neutral Silicon
Adhesive or equivalent manufacturer suggested adhesive. Rate to Include
Wastage as per design.
.

Note : Area to be measured and paid for the actual installed on site.

Digitally signed by AMIT

SINGH
13 Date: 2024.08.27 16:02:05 IST
 ROLLER SHADES: Providing & supplying of Window Blinds as per the approved
sample in required shade and style consisting, of Roller Blindscomprising of
optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-
480G weight per sq m, Thickness 0.67 mm, Yarn count 18-19/cm, having fire
resistance standard – NFPA 701-89 small testing ISO-5659-2 .Thetear resistance
should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE
UNIT shall be of clutch forquick,easy
andsafeinstallation,moldedplasticwithsteelspringsupportandinserted intothe
tubeend.Itshallbe drivenby a ball chain pulley with ball chain and can be
positioned at right side or left hand side of the Shade.The Shade whenlowering or
raising, shall be automatically locked in position upon release of the ball chain by
means of a built in friction lock.Universal clutch for left and right hand
operation.Chain Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic
witha steel location pin.The plug shall be inserted into the tube end.(Opposite to
the Drive Unit) for ease of installation. TheSUPPORT BRACKETS shall be of
9.06 MR coated steel & provided with covers and used in right hand or left handpositions 175 Sqm 2,760.00 483,000.00
differentiated by the acceptance of the of the rectangular drive unit support or the
round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame
(d) in Recess. The Bracket should be protruding outside maximum of80mm.The
ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter &
skin thickness of 1mm and shallincorporateakeywayintegral
withthetubetoaccommodatethespline. The BOTTOM RAIL shall be a Flat Bottom
made up of powder coated steel. The BALLCHAINshall be 2mm diameter cord
with 4.5mm diameter acetal balls molded co-axially toit on6mm
pitchtoformanendless ballchain.It is usedforraisingor loweringactionoftheshades.
including Providing and Fixing Somfy or equivalent make motors as per
manufacturer specifications in rating and configuration as per blinds suppliers
specifications and load capacity . Cost to include wireless remote per zone as
approved by Engineer in charge. All accessories and fittings to install motors with
Blind/Curtains shall be included in the cost.

Providing & Fixing UPVC sliding windows 2-track Minimum 2.5mm Gauge
(Medium) (Fenestech /Torfenster or of Approved Make) with 6mm glass with all
MR 30 Sqm 5,000.00 150,000.00
fittings like rollers, locking arrangement, beading, handle etc. & required hardware
of approved quality, etc.
DSR 2021 VOL-
1
Providing and fixing thermal insulation with Resin Bonded Fibre glass wool
conforming to IS: 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200G
9.07 12.57 Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in 300 Sqm 307.35 92,205.00
position by criss crossing GI wire etc. complete as per directions of Engineer-in-
Charge.
WINDOW CILL: Fabricate and install 250x200 (WxH), window cill along external
windows. Cill to be constructed out of 18 mm Plywood, finished with 1mm. Thk
9.11 MR 55 RM 1,770.00 97,350.00
laminate shade as per Engineer in charge’s approval. Cost to include edge
margin in teak wood and poilshed in colour matching laminate.
PELMET: Fabricate and install pelmet made of 18 mm thick Plywood, up to 300
mm high and 300 mm width in line with external glazing as per details of Engineer
9.12 MR in charge. Rate to include finishing exposed surfaces of the Pelmet with enamel 45 RM 1,770.00 79,650.00
paint of approved shade or 1mm laminate as approved by Engineer In Charge.

Digitally signed by AMIT

SINGH
14 Date: 2024.08.27 16:02:05 IST
 MIRROR PANELLING: P/F Mirror on a backing of Hollow Panelling of up to 75
mm depth and formed with 12 mm thick PLYWOOD with provision of light coves
and finished with 6mm Mirror of Glass framed in Metal Jamb Frame of PVD finish
of Approved make to be flush in level with adjoining surfaces. Cost to also include
9.13 MR 31 Sqm 2,800.00 86,800.00
Neutral Silicon Adhesive or equivalent manufacturer suggested adhesive as per
approved Design make and edge polishing. Cost to also include frosting/de
mirroring as per Engineer in charges Design.

10 Miscellaneous Work
General Notes:Fabricating and fixing built up storage cupboards as per detail. All
shutters, Carcass sides and Top, bottom along with shelves to be made out of
19mm BWP Ply as approved by the Engineer in charge. The storage Back to be
formed of 19 mm thick BWP Ply as approved by the Engineer in charge. All
internal and External surfaces to be faced with 1 mm thick laminate of approved
shade. Laminate to be pasted with High Quality fast setting Adhesive , Cost to
include all necessary fittings like tension hinges, ball catchers, tower bolts, locks,
handles, adjustable shelves etc. as per directions of Engineer in charge.

Adjustable Shelves to be provided as per the requirement and to be and to be

10.01
supported on SS Brackets. All the door and other exposed edges shall be
Finished with the PVC Edge Banding of approved make and Colour with
provision of finger grooves. Drawers shall be provided as per the requirement
and Drawings of the Engineer in charge with Handles and Soft Closing Channel
as approved by the Engineer in charge .
The storage to have all necessary
hardware, locks, handle etc. complete as per detail. All provision of fixing/hanging
the Storage on the Wall shall be done and included in the quoted rates.

FULL HEIGHT LAMINATED HINGED SHUTTER STORAGE: Providing and fixing

storage of depth up to 450 mm with Caracas and general Spec as 10.01 as
10.01.1 MR approved by the Engineer in charge and faced with 1.00 mm thick laminate and 15 Sqm 9,775.00 146,625.00
PVC edge Banding as per the selection of the Engineer in charge.

OVER HEAD STORAGE LAMINATED: Providing and fixing storage of depth up

to 450 mm with Caracas and general Spec as 10.01 as approved by the
Engineer in charge and faced with 1.00 mm thick laminate and PVC edge
10.01.2 MR Banding as per the selection of the Engineer in charge. 25 Sqm 9,775.00 244,375.00

MICROWAVE & CUTLERY STORAGE WITH OPEN SHELVES & DUSTBIN &
WATER DISPENSAR BLOCK: P/F Laminated Storage Shutters & open storage
with overall width of up to 650 mm deep with open & Closed shelves up to 450
mm High. The cabinet box of back//shelves /top/sides formed out of 19 mm Thk
HDMHR board with open shelves in fascia of 50 mm Thk double ply finished
upto 1.25 mm Laminate with PVC edge banding as per detailed drawing and as
10.01.5 MR 12 Sqm 10,625.00 127,500.00
directed by Engineer in charge. Storage to Comprise of Adjustable shelves /
Drawers with Auto close Telescopic channels as per Engineer in charge
approval.
Note : For Calculation of Rates the Overall front elevation
area shall be measured.
Digitally signed by AMIT
SINGH
15 Date: 2024.08.27 16:02:05 IST
 OVERHEAD OPEN & CLOSED SHELVING STORAGE : Providing and fixing up
to 450 mm deep open shelves cabinet with Closed Boxing /shutters as per
Engineer in charge Design with cabinet box/shelves /top/sides formed and back
of out of Double pressed 25 mm Thk Ply with all fascia members to be 50 mm
10.01.6 MR Double ply Thk finished with upto 1.25 mm Laminate with PVC edge banding as 2 Sqm 17,000.00 34,000.00
per detailed drawing and as directed by Engineer in charge. Each Compartment
considered 600 mm Wide with 400 mm High. Note : For Calculation of Rates the
Overall front elevation area shall be measured

SLOTTED ANGLE RACK: P/F slotted prime CRC Angle Racks in sturdy
demountable MS sections and framework with shelves finished in hot dip
galvanized/powder coated finishes as per approval for taking a load of
10.01.8 MR 20 Sqm 11,475.00 229,500.00
300kg/shelf with 4 intermediate shelved provided with adjustment provision with a
total height upto 2100 mm and depth of upto 600 mm.

CORNER GUARD FOR WALLS: Providing and fixing of Anodised Polished

Aluminium Corner Guards of 15mm x 15mm in all exposed Protruding corners as
10.02 MR per as per the colour and Design as approved by Engineer in charge. Cost to 15 RM 1,020.00 15,300.00
include fixing on the existing surface with neat structural tape without gaps and
undulations.

HAT SECTION PROFILE FOR WRITING GLASS: Providing and fixing of

Anodised Polished Aluminium T profile of 10 mm x 10 mm in all exposed edges
of Lacquered glass , Wall grooves as per the as per the colour and Design as
10.03 MR approved by Engineer in charge. Cost to include fixing on the existing surface with 72 RM 850.00 61,200.00
neat structural tape without gaps and undulations.

ENTRANCE MAT: P/F Dust mats as specified for all Main Entry Egress Points as
per the Colour and Size approved by the Engineer in charge. Euronics - Medium
10.04 MR Duty X-lertaor matting (8mm Thk) (MAT-02 or Equivalent as approved by 3 Sqm 3,876.00 11,628.00
Engineer in charge.

TUCK SHOP : P/F two level Tuck Shop Counter made of 19 mm Thk. BWP ply
and multi level fascia. The worktop shall have Granite top and the second level
will be 12th toughened glass top with etching film and clear edge polishing. This
will be fixed to the wood work with 25 dia. SS pipe and stud arrangement.
Aluminium skirting with other areas in laminated finish as per approval complete
MR with grooves. Over all assembly to incorporate a refrigerated pastry counter (To 1 Nos 80,000.00 80,000.00
be supplied by Pantry Equipment Supplier),cost of unit to be inclusive cost of
Acrylic Solid Surface top. This will also include a move-in Saloon door
arrangement.

Digitally signed by AMIT

SINGH
16 Date: 2024.08.27 16:02:05 IST
 6 PASSENGER ELEVATOR : Elevator Type :Passenger elevator :No of Units :1.
Load & Capacity :408 kg or 6 persons. Speed : 1 m/s. Stops & Openings : 2 stops
& 2 openings, Single entrance car. Travel height :8 m.
Elevator Grouping :SimplexFull Collective Control. Well Dimension:1550 mm
width and 1550 mm depth (required). Head Room height : 4500 mm (required).
Pit Height: 1500 mm (required). MAP Floor Position: Topmost floor (TOP). Car
dimensions: 1000 mm wide x 1050 mm deep x 2200 mm high. Door dimensions
:700 mm wide x 2000 mm internal height. Door type: Two-panel centre opening
Plain Panel.
MR 1 Nos 1,512,500.00 1,512,500.00
Finishes
Car design: SS silver brushed. Car Panel Finish: Stainless steel Hairline AISI441.
Handrail: Round Bend Handrail Silver brushed stainless steel (ST4) at Rear Wall.
Ceiling & Lighting : Integrated Roof RL20 Stainless Steel Ring Lighting LED :
Flooring 20 mm. Car skirting material: Stainless steel Hairline AISI441. Car Door
Finish: Stainless steel Hairline AISI441 including required civil and electrical works

G3.-68 RECEPTION DESK : Supply and installing reception desk as per

Architect/Designers design. Reception desk to consist of front and Side Runner
along with storage units. Front unit to have additional horizontal surface at ht.
1100 mm above the floor level and Working Top at 750 mm Height. Front & sides
finished with Lacquered Glass / Acrylic Solid Surface with Grooves and colour as
approved, with machine cut & polished edges and sides finished All other
MR exposed surface faced with 1mm Thk Laminate to Engineer in charge approval. 1 NUMBER 375000.00 375000
Table to have wire management detail, if required. Movable Laminated drawer
units to consist of one pencil drawer of 75 mm ht, two equal drawers and bottom
filing system drawers.Overall Length upto : Main Table - 2000mmx 800mm, Side
Runner - 900 mm x 600 mm.

G4.-78 BAIN MARIE CLADDING : P/F Bain Marie Cladding with counter comprising of
12mm Thk. acrylic solid surface finish top/ Front with SS inlay as per Dwg. All
other surfaces and 19mm Thk HDMHR carcass to be finished in 1.25 MM Thk
Laminate and SS skirting. Cost to also include shutters and storage in the back
4 RMTS 65000.00 260000
side as per the design. Fabrication to accommodates niches with lights for Plate
storage. All construction to be in BWP Ply. Consider Height Up to 1050 MM .

SIGNAGE - 2
Company name Logo cut in 3mm acrylic sheet, finished with brass/ golden
coolour / or any other colour SS plate, 3d letter CNC be cut to sizes and directly
10.06 MR installed on 3mm acrylic sheet with premiume quality adhesive tape, to be
hanged/fixed on wall/surface as per the requirement including necessary 1 Nos 35,000.00 35,000.00
hardware, substructure, extra, as specified and directed by Engineer in charge.
Base plate sizes to be measured for payment

Dismantling tile work in floors and roofs laid in cement mortar including stacking
15.23
material within 50 metres lead.
15.23.2 For thickness of tiles above 25 mm and up to 40 mm 380.00 SQM 93.40 35492.00
MR Dismantling tile work in Wall dado laid in cement mortar including stacking
175.00 SQM 97.26 17020.50
ased on 15.23.2 material within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for Digitally signed by AMIT
15.56 175.00 SQM 45.05 7883.75 SINGH
plaster including disposal of rubbish to the dumping ground within 50 metres lead. Date: 2024.08.27 16:02:05 IST
17
 Demolishing brick work manually / by mechanical means including stacking of
15.7 serviceable material and disposal of unserviceable material within 50 metres lead
as per direction of Engineer-in-Charge.
15.7.4 In cement mortar 2.00 CUM 1698.45 3396.90
Dismantling doors, windows and clerestory windows (steel or wood) shutter
15.12 including chowkhats, architrave, holdfasts etc. complete and stacking within 50
metres lead:
15.12.1 Of area 3 sq. metres and below 2.00 EACH 302.70 605.40
15.12.2 Of area beyond 3 sq. metres 2.00 EACH 414.55 829.10
Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and
15.57 false ceiling including disposal of unserviceable surplus material and stacking of 145.00 SQM 46.50 6742.50
serviceable material with in 50 meters lead as directed by Engineer-in-Charge.

Demolishing cement concrete manually / by mechanical means including disposal

15.2
of material within 50 metres lead as per direction of Engineer-in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 2.00 CUM 2007.10 4014.20
Dismantling C.I. pipes including excavation and refilling trenches after taking out
the pipes, manually / by mechanical means breaking lead caulked joints, melting
15.45
of lead and making into blocks including stacking of pipes & lead at site within 50
metre lead as per direction of Engineer-in- Charge:
15.45.1 Up to 150 mm diameter 15.00 RM 340.70 5110.50
Dismantling G.I. pipes (external work) including excavation and refilling trenches
15.44 after taking out the pipes, manually / by mechanical means including stacking of
pipes within 50 metres lead as per direction of Engineer-in-Charge:
15.44.1 15 mm to 40 mm nominal bore 10.00 RM 124.10 1241.00
15.44.2 Above 40 mm nominal bore 10.00 RM 134.25 1342.50
Dismantling of flushing cistern of all types (C.I. /PVC/Vitrous China) including
15.52 stacking of useful materials near the site and disposal of unserviceable materials 2.00 Nos 744.60 1489.20
within 50 metres lead.
MR Based
Dismantling of Wash basins, Urinals, WC including stacking of useful material
on item No 2.00 Nos 668.14 1336.28
near the site and disposal of unservicable materials within 50 metres lead
15.52
Demolishing R.C.C. work manually / by mechanical means including stacking of
15.3 steel bars and disposal of unserviceable material within 50 metres lead as per 1.00 cum 2928.10 2928.10
direction of Engineer-in-Charge.
Extra for cutting reinforcement bars manually / by mechanical means in R.C.C. or
15.5 R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. 5.00 sqm 947.10 4735.50
work) as per direction of Engineer - in -charge.
Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B.
15.6 10.00 kg 7.45 74.50
work.
Carriage of material by mechanical transport including loading unloading and
1.1
stacking
1.1.1 Lime, murrum, building rubbish
upto 30 kms 50.00 Cum 522.56 26128.00

11 ART WORK

Digitally signed by AMIT

SINGH
18 Date: 2024.08.27 16:02:05 IST
 Canvas paintings (Oil/ Acrylic medium)
Concept Creation
Creating design and creation of Art work concept on given subject. With initial visit
to site, preparation of various designs with different material, providing the
samples, layout for approval, improvisation in short listed creative’s and making of
final layout for final production by enlargement of drawing as per ratio of actual
11.01 MR size, to prepare detailed working shop drawings (full scale) based on the Concept 26 Sqm 9,658.00 251,108.00
drawings/ Views/ site conditions, display of actual size dummy/ mock up
fabricated in sun board with digital print for client approval

ART WORK EXECUTION

Towards the cost of doing canvas painting by qualified artist including frame and
installation at site

12 Horticulture and Landscaping

12.01 MR Supply and Planting Draco plant having 6ft height complete. 5 Each 3,250.00 16,250.00
Supply and Planting Monstera plant having 3-4 ft height complete.
12.02 MR 20 Each 1,425.00 28,500.00
Supply and Planting Lolina plant having 2-3 ft height with Coco-peat, mud and
12.03 MR 20 Each 970.00 19,400.00
manure complete.
Providing and displaying of Seaforthia Palm having ht. 90 cm to 1.20 m
with 6-8 suckers, well developed, fresh and healthy lush green leaves from
12.04 3.81 20 Each 180.00 3,600.00
bottom to top in 20 cm size of Earthen pot/Plastic pot & as per direction of
the officer-in-charge.

Providing and displaying of Raphis palm specimen plant, having ht. 1.50 m to
1.65 m with 40 to 50 lush green suckers, well developed, fresh & healthy foliage
12.05 3.78 12 Each 270.00 3,127.41
leaves in 40 cm size of Earthen Pot / Chali / Tray & as per direction of the officer-
in-charge.
Supply of full soil fill conical shaped planters of specified volume and dimensions
in stone finish or equivalent. planters to be indigenously made by rotational
moulding, with homogeneous recyclable, industrial grade polymer-resin mix, and
textured surface. planters should have an integrated water outlet hole & plug,
single layered peel-proof construction, light weight, rust proof, uv stabilized, anti-
12.06 MR frost feature without any joints, and easy to clean. planter supplier must give 1
year warranty against any fading or cracking for both indoor and outdoor use.
green plant and laying is extra. potting instructions as per company catalogue.

12.06(a) C-1613 - 40 (D) X 33(H) CM ; V- 27LTR 20 Each 970.50 19,410.00

12.06(b) C-2016 49 (D) X 41 (H) CM V- 51LTR 20 Each 1,168.50 23,370.00
12.06© C-2420 61 (D) X 51(H) CM ; V- 100 LTR 20 Each 1,625.00 32,500.00

Digitally signed by AMIT

SINGH
19 Date: 2024.08.27 16:02:05 IST
 Supply of double layered translucent backlit cylinderical shaped - hand carfted
pattern planters of volume 18 ltr; approx. dimension 24(h)x18(d) in granite/
stone/ solid finish or equivalent. planters to be indigenously made by rotational
moulding, with homogeneous 100% recyclable, industrial grade polymer-resin
mix, with textured surface and stone match finishes. planters to have concealed
shock resistant back lighting system with secured supply wire and an integrated
12.07 MR 10 Each 4,500.00 45,000.00
water outlet hole & plug, peel proof construction, asbestos free, light in weight,
without any joints, rust proof, uv stabilized, anti-frost feature and easy to clean.
planter supplier must give 1 year warranty against any led, fading or cracking for
indoor and outdoor use.

Supply of double layered translucent backlit cylinderical shaped - hand carfted

pattern planters of volume 40 ltr; approx. dimension 40(h)x18.5(d) in granite/
stone/ solid finish or equivalent. planters to be indigenously made by rotational
moulding, with homogeneous 100% recyclable, industrial grade polymer-resin
mix, with textured surface and stone match finishes. planters to have concealed
12.08 MR shock resistant back lighting system with secured supply wire and an integrated 10 Each 6,750.00 67,500.00
water outlet hole & plug, peel proof construction, asbestos free, light in weight,
without any joints, rust proof, uv stabilized, anti-frost feature and easy to clean.
planter supplier must give 1 year warranty against any led, fading or cracking for
indoor and outdoor use.

MR Third Party Inspection charges 1 Lot 600,000.00 600,000.00

To provide the drawings & Lift aprroval from NDMC for the interior fitout of CGHS
MR 1 Lot 300,000.00 300,000.00
MCTC office

5,803,051.02 12,990,961.00

GRAND TOTAL 18,794,012.02

Digitally signed by AMIT

SINGH
20 Date: 2024.08.27 16:02:05 IST
PROJECT : OFFICE INTERIORS FOR CGHS AT NEW DELHI
SUBHEAD : SANITARY PLUMBING INSTALLATIONS
TOTAL PLUMBING WORK AMOUNT

DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-

S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)

1 Providing and Fixing soil, waste and vent pipes.

100mm dia Centrifugally cast (spun) iron socketed pipe as per IS:
a 17.35.1.2 M 55.00 ₹ 1,077.40 ₹ 59,257.00
3989

Providing and fixing PTMT Bottle Trap for Wash basin and sink.
Bottle trap 38 mm single piece moulded with height of 270 mm,
2 17.70.2 effective length of tail pipe 260 mm from the centre of the waste Each 20.00 ₹ 325.10 ₹ 6,502.00
coupling, 77 mm breadth with 25 mm minimum water seal, weighing not
less than 263 gms

Providing and Fixing trap of self cleansing design with screwed down or
3 hinged grating with or without vent arm complete, including cost of
cutting and making good the floor and walls

a 17.60.2.2 100mm inlet and 100mm outlet Sand cast iron S&S as per IS - 3989 Each 18.00 ₹ 1,604.10 ₹ 28,873.80

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent
4 pipes and fittings with paint of any colour such as chocolate grey or buff
etc. over a coat of primer (of approved quality) for new work.
a 17.65.1 100mm dia meter pipe M 55.00 ₹ 69.55 ₹ 3,825.25

Providing and fixing bend of required degree with access door

5
insertion rubber washer 3mm thick bolts and nuts complete
a 17.38.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 20.00 ₹ 597.70 ₹ 11,954.00
b 17.38.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 0.00 ₹ 453.40

6 Providing and fixing plain bend of required degree

a 17.39.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 20.00 ₹ 439.75 ₹ 8,795.00

Providing and fixing single equal plain junction of required degree with
7 access door, insertion rubber washer 3 mm thick, bolts and nuts
complete.
a 17.44.1.2 100x100x100 mm Sand cast iron S&S as per IS - 3989 Each 20.00 ₹ 707.30 ₹ 14,146.00

8 Providing and fixing collars

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)
a 17.57.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 60.00 ₹ 439.75 ₹ 26,385.00

Providing lead caulked joints to sand cast iron/centrifugally cast

9
(spun) iron pipes & fittings of dia
a 17.58.1 100mm Each 60.00 ₹ 549.65 ₹ 32,979.00

Providing and fixing C.P. brass long body bib cock of approved quality
10 18.51
conforming to IS standards and weighing not less than 690 gms.

a 18.51.1 15 mm nominal bore Each 2.00 ₹ 708.40 ₹ 1,416.80

Providing and fixing C.P. brass angle valve for basin mixer and gyser
11
points of approved quality conforming to IS : 8931
a 18.53.1 15 mm nominal bore Each 75.00 ₹ 500.35 ₹ 37,526.25

Cutting chases in brick masonry walls for following diameter sand cast
iron/centrifugally cast (spun) iron pipes and making good the same with
12 17.61 cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 12.5 m nominal size) including necessary plaster and
pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :
a 17.61.1 100 mm dia M 20.00 ₹ 615.70 ₹ 12,314.00

13 18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.
18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 30.00 ₹ 362.40 ₹ 10,872.00

Making chases upto 7.5 X 7.5 cm in walls including making good after
14 18.78 M 30.00 ₹ 171.80 ₹ 5,154.00
housing G.I. pipe etc.

Providing and fixing in position, the following G.I. medium class Waste
Pipes (IS:1239) with all necessary specials complete, cutting and
15 MR
chasing walls, floors, etc. and making good the same including painting
the pipes with two coats of anti-corrosive paint.
a) 32 mm dia pipe M 24.00 ₹ 800.00 ₹ 19,200.00
b) 40 mm dia pipe M 25.00 ₹ 1,100.00 ₹ 27,500.00
c) 50 mm dia pipe M 165.00 ₹ 1,400.00 ₹ 231,000.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)
Providing and fixing floor trap Extension Piece made out of 100 mm
dia M.S pipe ( medium grade) of required length (upto 450 mm) with 32
mm to 50 mm dia threaded maleable iron sockets ( maximum 4 nos.)
16 MR welded as side inlets, neatly finished, inside and outside epoxy painted, Each 18.00 ₹ 1,500.00 ₹ 27,000.00
including the cost of jointing with floor trap with dripseal joint.

Providing, installing, testing and commissioning of package sump unit

with built-in submersible drainage pump, nonreturn valves, cutter,
electrical panel/starter, all as per standard design and including making
17 MR
connections with grease separator/sink waste pipes drain pipe and
make it operational

Model: Sanispeed ( for Pantry) Each 2.00 ₹ 75,000.00 ₹ 150,000.00

Model: Sanipack ( for Toilet) Each 0.00 ₹ 85,000.00 ₹ -
Model: Sanicubic classic-2 ( for Toilet) Each 3.00 ₹ 245,000.00 ₹ 735,000.00

Providing and fixing floor drain points formed out of 100X50 mm dia
elbow with suitable extension piece, complete,setting in 1:2:4 mix
18 MR cement concrete block or clamping to the wall or suspending with the Each 10.00 ₹ 750.00 ₹ 7,500.00
ceiling including cutting and making good the walls and floors wherever
required.

Providing and fixing screwed down type nickel bronze alloy cast floor
cleanout/ CO with opening arrangements for soil / waste pipe and
19 MR other necessary fittings inlcuding jointing, all complete as per standard
detail.
a) for 100 mm dia pipe Each 4.00 ₹ 2,200.00 ₹ 8,800.00

Providing and fixing 110 mm dia round chrome plated bronze grating
20 MR Each 21.00 ₹ 600.00 ₹ 12,600.00
with frame, rotate lock type embedded in floor, all complete.

Making connection with existing C.I. Soil and Waste pipework. The
work includes loosening / removing the existing lead joints, rotating the
direction of the existing tees, bends etc. so as to connect with new
21 MR branch lines from the toilets, redoing the joints with 'Dripsel', testing, Each 4.00 ₹ 2,000.00 ₹ 8,000.00
commissioning all complete. Any pipe piece, fittings etc. required to
make the connection shall be measured in Item No. 2.1

Providing, installing, testing and commissioning of Grease Separator

having grease storage capacity of 9 litre and total iquid holding capacity
22 MR of 34.3 litre , all as per standard design and including making
connections with scullery sink

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)

Material : Fabricated with 2 mm

thick SS 304 grade stainless Each 1.00 ₹ 52,000.00 ₹ 52,000.00
steel sheet

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all CPVC
plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m
spacing.
23
This includes jointing of pipes & fittings with one step CPVC solvent
cement and the cost of cutting chases and making good the same
including testing of joints complete as per direction of Engineer in
Charge.
Concealed work including cutting chases and making good the
walls etc.
a 18.8.1 15mm nominal outer dia pipes M 110.00 ₹ 441.15 ₹ 48,526.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all CPVC
plain & brass threaded fittings, including fixing the pipe with clamps at
24
1.00 m spacing. This includes jointing of pipes & fittings with one step
CPVC solvent cement and testing of joints complete as per direction of
Engineer in Charge.
18.7.1 15 mm nominal outer dia Pipes M 190.00 ₹ 255.90 ₹ 48,621.00
18.7.2 20 mm nominal outer dia Pipes M 55.00 ₹ 325.10 ₹ 17,880.50
18.7.3 25 mm nominal outer dia Pipes M 55.00 ₹ 408.55 ₹ 22,470.25
18.7.4 32 mm nominal outer dia Pipes M 60.00 ₹ 500.95 ₹ 30,057.00
18.7.5 40 mm nominal outer dia Pipes M 100.00 ₹ 674.35 ₹ 67,435.00
18.7.6 50 mm nominal outer dia Pipes M 210.00 ₹ 927.00 ₹ 194,670.00

Providing and fixing insulation to hot water piping with closed cell
chemically cross-linked polyethylene ( XLPE) preformed pipe sleeves
25 MR of specified wall thickness using propriety adhesive and self adhesive
tapes, all as per the manufacturer's specifications. (For exposed water
pipes in plumbing shaft and on terrace)
a MR a) 15 mm dia - 9 mm thickness M 70.00 ₹ 95.00 ₹ 6,650.00
b MR b) 20 mm dia - 9 mm thickness M 5.00 ₹ 110.00 ₹ 550.00

Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete with hard chrome plated ball
26 18.18 inside PTFE (Teflon) seat & ring with chrome plated centre handle with
female BSP threads complete:in all respects (PN 1.6). Tested to 25
kg/cm2 hyd.
18.18.1 15 mm dia Each 2.00 ₹ 348.85 ₹ 697.70

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)
18.18.2 20 mm dia Each 3.00 ₹ 397.45 ₹ 1,192.35
18.18.3 25 mm dia Each 2.00 ₹ 399.05 ₹ 798.10
MR 32 mm dia Each 5.00 ₹ 1,400.00 ₹ 7,000.00
MR 40 mm dia Each 3.00 ₹ 1,650.00 ₹ 4,950.00
MR 50mm dia Each 4.00 ₹ 1,800.00 ₹ 7,200.00

Providing and fixing gun metal non- return valve of approved quality
27 18.19 (screwed
end) :
NRV
18.19.2.2 32 mm dia. nominal bore Each 2.00 ₹ 777.90 ₹ 1,555.80
18.19.4.2 50 mm dia. nominal bore Each 3.00 ₹ 1,320.80 ₹ 3,962.40

Providing and fixing unplasticised PVC connection pipe with brass

28 18.21
unions.
a 18.21.1.1 30cm lengh &15 mm nominal bore Each 75.00 ₹ 74.80 ₹ 5,610.00

Providing and fixing electric water storage heater (geyser) of following

29 MR capacities including making inlet / outlet connections, of approved
makes.

a) Capacity : 25 litre Each 6.00 ₹ 9,500.00 ₹ 57,000.00

a) Capacity : 50 litre Each 1.00 ₹ 14,500.00 ₹ 14,500.00

Providing and fixing white vitreous china clay wall mounted

European type Water Closet (EWC) with dual flush concealed
cistern of approved make, of approved shade including matching
shade of plastic seat and lid cover, fittings, connectors, necessary
30 MR hanging arrangement, rubber buffers etc. including cutting and making Each 19 ₹ 16,000.00 ₹ 304,000.00
good the wall and floors wherever required, making connections to soil
/ vent pipe etc., complete in all respects inclusive of cost of all required
fittings, fixtures, materials, labour, tools, tackles etc. as per
specifications and direction of Engineer-in-Charge.

Providing and fixing glazed vitreous China rectangular wash basin of

560x410 mm size of approved make similar with MS or CI brackets
painted white, C.P. brass chain with rubber plug, 32 mm CP brass
waste coupling of standard pattern, 32 mm CP brass bottle trap and
31 MR
union, 32 mm dia C.P. pipes to wall flange etc. including cutting and
making good the walls & floors where required complete in all respects
inclusive of cost of all required fittings, fixtures, materials, labour, tools,
tackles etc. as per specifications and direction of Engineer in Charge

a) White colour Each 14 ₹ 18,000.00 ₹ 252,000.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)

Providing and fixing stainless steel sink of approved make with

40mm dia CP brass waste coupling of standard pattern, CP brass
chain & plug, 40 mm dia PVC waste, CP grating including fixing under
32 17.10 counter top, cutting and making good the walls & floors where required
complete in all respects inclusive of cost of all required fittings, fixtures,
materials, labour, tools, tackles etc. as per specifications and direction
of Site Engineer.
a) Stainless steel sink single bowl with drain board of overall size
17.10.1 Each 6.00 ₹ 6,008.45 ₹ 36,050.70
510mmx1040mm, 250mm deep

Providing and fixing ivory coloured vitreous china flat back urinal
basin set of Urinals approved make with auto sensor flushing system
with built in sensor including spreader, all fittings, brackets for wall
fixing, connection pipe, waste pipe etc. for individual urinal including
33 MR Each 9.00 ₹ 11,500.00 ₹ 103,500.00
cutting and making good the walls and floors wherever required etc.,
complete in all respects inclusive of cost of all required fittings, fixtures,
materials, labour, tools, tackles etc. as per specifications and direction
of Site Engineer.

Providing and fixing CP Central hole single lever wash basin mixer
with tuchfree senser & popup waste system with 2 nos. 10 mm dia.
34 MR 450mm long copper pipes and brass nuts, size 15mm including cutting Each 14.00 ₹ 10,800.00 ₹ 151,200.00
and making good the walls where required complete in all respects as
per direction of Engineer-in-Charge.

Providing and fixing sensor based CP brass tap with CP brass

flange including cutting and making good the walls where required
35 MR complete in all respects inclusive of cost of all materials, labour, tools, Each 6.00 ₹ 1,800.00 ₹ 10,800.00
tackles etc. as per specifications and direction of Site Engineer. Two
way Bib Cock with wall flange.

Supply and fixing of all accessories for wash room including hand
36 MR dryer, shoe polisher, touch-free sanitizer, touch free soap dispenser, Nos. 3.00 ₹ 85,000.00 ₹ 255,000.00
multi recess panel,airpurifier, console,

Recess Panel 3 in 1 Panel (Hand Dryer + Auto Tissue Roll Dispenser

+ Waste Receptacle), Multifunction Recessed Washroom Panel
(Consisting of Hand Dryer + Auto Tissue Roll Dispenser + Waste
Receptacle) ,Hand Dryer :1350W,Wall Opening Required : 320mm (W)
x 1605mm (H) x 160mm (D)

Twin Toilet Paper Holder - Steel Twin Toilet Paper Holder -

Steel,Application : WC Cubicle Area

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR NO. TOTAL AMOUNT TOTAL AMOUNT NON-
S NO. DESCRIPTION OF ITEM UNIT BOQ QTY. RATE
2021 DSR (INR) DSR (INR)

Providing and fixing storage of depth up to 450 mm with Caracas and

shutters in 19 mm thk HDMHR Board in colour and design as
37 MR approved by the Engineer in charge and faced with 1.00 mm thick Sqm 3.00 ₹ 13,500.00 ₹ 40,500.00
laminate and PVC edge Banding as per the selection of the Engineer in
charge.

Supplying & fixing in position Toilet Cubicle as per standard

manufacturers specifications closest to the following standard
dimension which includes 600mm door size width made of heat,
bacteria, water, chemical, scratch and impact resistant 12mm thick
solid compact laminate pane including doors, pilasters & intermediate
pane finished with approved texture/shade as per the detail drawings
This also includes providing and fixing in position necessary hardware
made out of Stainless steel (Grade 304) as per manufacturer’s
specifications & Engineer in charges instructions like (1) Door Knob, (2)
Gravity Hinges, (3) Thumb turn lockset with Occupancy indicators, (4)
38 MR Coat hooks with Door stopper (5) U channel , (6) adjustable No. 18.00 ₹ 40,000.00 ₹ 720,000.00
foot/pedestal, (7) Top rail with Corner connector (8) Rubber noise
deafening tape, (9) Screws & wall Plugs.
The top fitting should consist of SS round top rail which will get fixed
with pilasters, with SS panel tube holder, SS corner bend (connected
with top rail) will be used on the corner of cubicle in absence of brick
wall, SS wall fixing is used only on the wall which will hold the ss top rail.
All screws will of 304 Grade in stainless steel with satin finish. All
pilasters are supported by stainless steel Bottom Cladding. The base of
the stainless steel bottom cladding will be anchored to the floor with a
clearance height up to 150mm.

Providing and Fixing Urinal Dividers with a Outline profile as approved

by Engineer in charge in Frosted Tempered Glass 12 MM Thick and
39 MR No. 11.00 ₹ 2,500.00 ₹ 27,500.00
each divider to be installed with minimum 3 Ozone U Brackets with
Concealed Screwing mechanism.

Providing and fixing high density Polyethelene (Sintex type) three layer
single piece water storage tanks/loft tank with cover, inlet and outlet,
scour and overflow & vent connections shall be provided with
40 MR No. 1.00 ₹ 80,000.00 ₹ 80,000.00
necessary nipples and flanges, fabricated with GI/ CPVC pipes, heavy
duty float valve all complete as per Detail. of following capacity : 5000
Litres. MS Base also included above.

TOTAL PLUMBING WORK AMOUNT ₹ 746,727.40 ₹ 3,313,750.00

Grand Total ₹ 4,060,477.40

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR (E & DESCRIPTION UNIT QTY RATE TOTAL AMOUNT TOTAL AMOUNT
SNO. M - 2022)
/ MR N0N -DSR (
DSR ( INR )
INR )
A POINT WIRING
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm
FRLS PVC insulated copper conductor single core cable in surface / recessed
1 1.10 medium class PVC conduit, with modular switch, modular plate, suitable GI box
and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor
single core cable etc as required.
1.10.3 Group C Point 145 1467.00 ₹ 212,715.00
Wiring for group controlled (looped) light point/ fan point/call bell point (without
independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor
2 1.55 single core cable in surface / recessed PVC conduit, and earthing the point with
1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as
required.
1.55.3 Group C Point 329 858.00 ₹ 282,282.00
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper
conductor single core cable in surface/ recessed medium class PVC conduit
3 1.5 alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable Metre 900 433.00 ₹ 389,700.00
for loop earthing as required.
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper
conductor single core cable in surface/ recessed medium class PVC conduit
4 1.6 alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable Metre 50 662.00 ₹ 33,100.00
for loop earthing as required.
Supplying and fixing following modular switch/ socket on the existing modular plate
5 1.24 & switch box including connections but excluding modular plate etc. as required.

1.24.1 5/6 amps switch Each 425 103.00 ₹ 43,775.00

1.24.3 15/16 amp switch Each 50 156.00 ₹ 7,800.00
1.24.4 3 pin 5/6 amp socket outlet Each 390 122.00 ₹ 47,580.00
1.24.5 6 pin 15/16 amp socket outlet Each 49 197.00 ₹ 9,653.00
Supplying and fixing following size/module, GI box along with Modular base &
6 1.27
cover plate on existing modular metal boxes etc. as required.
1.27.2 3 Module Each 205 327.00 ₹ 67,035.00
1.27.3 4 Module Each 50 343.00 ₹ 17,150.00
1.27.4 6 Module Each 140 402.00 ₹ 56,280.00
1.27.5 8 Module Each 5 454.00 ₹ 2,270.00
B SUBMAIN AND CONTROL WIRING
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR
B.1 1.14 PVC insulated copper conductor, single core cable in surface/ recessed medium
class PVC conduit as required
1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 1400 275.00 ₹ 385,000.00
1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 500 334.00 ₹ 167,000.00
Digitally signed by AMIT
1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 100 439.00 ₹ SINGH
43,900.00
1 Date: 2024.08.27 16:02:05 IST
 1.14.6 2 X 16 sq. mm + 1 X 6 sq. mm earth wire Metre 80.00 772.00 ₹ 61,760.00
1.14.11 4 x 16 sq.mm + 2 x 6 sq.mm. earth wire Metre 80.00 1,365.00 ₹ 109,200.00
Supply and drawing following sizes of FR PVC insulated copper conductor, single
1.17
core cable in the existing surface/ recessed steel / PVC conduit as required
1.17.12 3 X 2.5 sq. mm Metre 700 137.00 ₹ 95,900.00
1.17.21 3 X 4 sq. mm Metre 600 206.00 ₹ 123,600.00
Supplying and fixing of following sizes medium class PVC conduit aong with
B.2 1.21 accessories in surface/ recess including cutting the wall and making good the
same incase of recessed conduit as required
1.21.2 25 mm Metre 800 145.00 ₹ 116,000.00
1.21.3 32 mm Metre 300 184.00 ₹ 55,200.00
C CABLES
Supplying and making end termination with brass compression gland and
C.2 9.1 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE
aluminium conductor cable of 1.1 KV grade as required.
9.1.27 3½ X 185 sq. mm (57mm) Each 2 875.00 ₹ 1,750.00
9.1.32 4 X 10 sq. mm (25mm) Each 8 269.00 ₹ 2,152.00
9.1.33 4 X 16 sq. mm (28mm) Each 10 309.00 ₹ 3,090.00

Supply of following size cables & making proper end termination with sutable
3 MR accessories of under noted sizes of copper conductor PVC insulated PVC sleeved
1.1 KV grade power distribution flexible cable/wires heavy duty conforming to
relevant IS code and as per specification in ground or in existing trenches/ through
pipe/ on wall / on cable trays including dressing and clamping the cable as required.
a 1 x 25 sq.mm PVC insulated flexible copper conductor cables RM 150.00 482.00 ₹ 72,300.00
b 1 x 10 sq.mm PVC insulated flexible copper conductor cables RM 50.00 134.00 ₹ 6,700.00
c 4 x 16 sq.mm XLPE armoured copper cable RM 250.00 1,007.00 ₹ 251,750.00
d. 4 x 10 sq.mm XLPE armoured copper cable RM 80.00 756.00 ₹ 60,480.00
e 4 x 6 sq.mm XLPE armoured copper cable RM 105.00 502.00 ₹ 52,710.00
f 4 x 2.5 sq.mm XLPE armoured copper cable RM 120.00 227.00 ₹ 27,240.00
g 3.5 x 185 sq.mm XLPE armoured aluminium cable RM 220.00 1,541.00 ₹ 339,020.00

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power
7.8
cable of 1.1 KV grade of following size on cable tray as required.
7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Metre 805.00 45.00 ₹ 36,225.00
Above 95 sq. mm and upto 185 sq. mm (clamped with 25x3mm
7.8.2 Metre 220.00 92.00 ₹ 20,240.00
MS flat clamp)

D DISTRIBUTION BOARD
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature
circuit breaker suitable for inductive load of following poles in the existing MCB DB
D.2 2.10 complete with connections, testing and commissioning etc. as required.

2.10.1 Single pole Each 220 256.00 ₹ 56,320.00

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing
2.13
MCB DB complete with connections, testing and commissioning etc. as required.
Digitally signed by AMIT
2.13.2 63 amps Each 6 1,034.00 ₹ 6,204.00
SINGH
2 Date: 2024.08.27 16:02:05 IST
 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415
volts, TPN MCB distribution board of sheet steel, dust protected, duly powder
painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth
D.3 2.5 bar, din bar for mounting MCB’s (but without MCB’s and incomer ) as required .
(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are
required.)
2.5.3 12 way (4 + 36), Double door Each 6 12833.00 ₹ 76,998.00
Supplying and fixing following way, single pole and neutral, sheet steel, MCB
distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar,
2.3 neutral bus bar, earth bar, din bar, interconnections, powder painted including
earthing etc. as required. (But without MCB/RCCB/Isolator)
2.3.2 8 way , Double door Each 2 2573 ₹ 5,146.00
2.3.3 12 way , Double door Each 1 2315 ₹ 2,315.00
Supplying and fixing following rating, double pole, (single phase and neutral), 240
volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300
D.5 2.14 milliamperes in the existing MCB DB complete with connections, testing and
commissioning etc. as required.
2.14.3 63 amps Each 21 2722.00 ₹ 57,162.00
Supplying and fixing following rating ,double pole, 240 Volts, isolator in the existing
2.12
MCB DB complete with connections, testing and commissioning etc. as required.
2.12.2 63 amps Each 3 527 ₹ 1,581.00

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate
E.16 1.24 & switch box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 2 148.00 ₹ 296.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways
E.20 MR along with required suitable number of GI couplers for joining raceways and fixing
GI brackets and all accessories complete in all respect as per the directions of
engineer in charge
(b) 250mmx40mm(GI) Mtr 100 1264.00 ₹ 126,400.00
(c ) 150mmx40mm(GI) Mtr 90 1057.00 ₹ 95,130.00
(d) 100mmx40mm(GI) Mtr 90 823.00 ₹ 74,070.00
Supply, Installation, Testing and Commisioning of Junction boxes for direct access
to cables at the intersection of raceways supplied completely with base and cover
E.21 MR plates, height adjustable junction box 65- 90 mm including all accessories
complete in all respect as per the directions of engineer i
(a) 300x 300 x 65-90 mm Each 30 1000.00 ₹ 30,000.00
(b) 225x 225x 65-90 mm Each 30 900.00 ₹ 27,000.00
(c ) 150x 150 x 65-90 mm Each 10 800.00 ₹ 8,000.00
(d ) 100x 100 x 65-90 mm Each 10 700.00 ₹ 7,000.00
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper
E.22 1.19 conductor PE insulated, shielded with fine tinned copper braid and protected with Metre 300 47.00 ₹ 14,100.00
PVC sheath in the exisitng surface/recessed steel/ PVC conduit as required
Supplying and Installation of following size perforated of painting with powder
coating M.S. cable trays of perforation of not more than 17.5% in convinient
E.24 4.1 sections, joined with connectors suspended from the cieleing with MS suspenders
Digitally signed by AMIT
SINGH
including bolts and nuts painting suspenders etc as required Date: 2024.08.27 16:02:05 IST
3
 4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 5 1137.00 ₹ 5,685.00
4.1.4 300 mm width x 50 mm depth x 1.6 mm thickness Metre 90 777.00 ₹ 69,930.00
4.1.2 150 mm width x 50 mm depth x 1.6 mm thickness Metre 200 604.00 ₹ 120,800.00

EARTHING
Earthing with G.I. earth plate 600 mm X 600 mm X 3 mm thick including
5.4 accessories, and providing masonry enclosure with cover plate having locking SET 2 7472.00 ₹ 14,944.00
arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt
as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
1 5.6 arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt SET 3 13838.00 ₹ 41,514.00
as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for

2 5.14 MTR 50 1162.00 ₹ 58,100.00
connections etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for
3 5.15 MTR 150 244.00 ₹ 36,600.00
connections etc. as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing
4 5.16 MTR 400 70.00 ₹ 28,000.00
as required.
PANEL BOARDS
14 MR Floor Panels
Designing, fabricating, transporting, unloading, storing, fixing in position, testing
and commissioning the following sheet steel cubicle type panels fabricated from
1.6mm thick CRCA sheet, dust and vermin proof, indoor type TPN Panels with
hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3
phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated Each 1 270085.00 ₹ 270,085.00
bus-bar chamber with tinned aluminium bus bar of capacity 500 AMPS and
including supplying and fixing following switchgears, meters and accessories, inter-
connections, bonding to earth, powder coated painting and marking as specified.
Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42
The LT PANEL shall be electrically inter-locked as shown in Schematic diagram
and as detailed in the Specifications
Colour: Gray Powder Coated, as per approved sample.
Incomings:
1 nos, 400 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of
fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect
Bus Bars:
TPN aluminum bus bars of minimum of 250 Amps capacity with heat shrinkable
colored sleeves and I/C DMC/SMC bus bars supports at required intervals
complete for cross section, size supports & their spacing etc. for withstanding fault
level of 25 MVA for 1 Sec.
Outgoings:
(a) 125 Amps, TPN, MCB -4 Nos.
(a) 63 Amps, FP, MCB -12 Nos.
(a) 32 Amps, FP, MCB -4 Nos.
(b) 40 Amps, DP, MCB - 4 nos Digitally signed by AMIT
(b) 16 Amps, 4P, MCB - 4 nos SINGH
4 Date: 2024.08.27 16:02:05 IST
 Panel complete as above
15 MR UPS Panel
Designing, fabricating, transporting, unloading, storing, fixing in position, testing
and commissioning the following sheet steel cubicle type panels fabricated from
1.6mm thick CRCA sheet, dust and vermin proof, indoor type TPN Panels with
hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3
phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated Each 1 142060.00 ₹ 142,060.00
bus-bar chamber with tinned aluminium bus bar of capacity 200 Amps and
including supplying and fixing following switchgears, meters and accessories, inter-
connections, bonding to earth, powder coated painting and marking as specified.
Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42
The LT PANEL shall be electrically inter-locked as shown in Schematic diagram
and as detailed in the Specifications
Colour: Gray Powder Coated, as per approved sample.
Incomings:
1 nos, 125 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of
fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

Bus Bars:
TPN copper bus bars of minimum of 150 Amps capacity with heat shrinkable
colored sleeves and I/C DMC/SMC bus bars supports at required intervals
complete for cross section, size supports & their spacing etc. for withstanding fault
level of 25 MVA for 1 Sec.
Outgoings:
(A) 63 Amps, FP, MCB - 6 nos
(B) 40 Amps, FP, MCB - 4 nos
(C ) 63 Amps, DP MCB - 3 nos
Panel complete as above
15 MR HVAC PANEL
Designing, fabricating, transporting, unloading, storing, fixing in position, testing
and commissioning the following sheet steel cubicle type panels fabricated from
1.6mm thick CRCA sheet, dust and vermin proof, indoor type TPN Panels with
hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3
phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated Each 1 125845.00 ₹ 125,845.00
bus-bar chamber with tinned aluminium bus bar of capacity 160 amps and
including supplying and fixing following switchgears, meters and accessories, inter-
connections, bonding to earth, powder coated painting and marking as specified.
Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42
The LT PANEL shall be electrically inter-locked as shown in Schematic diagram
and as detailed in the Specifications
Colour: Gray Powder Coated, as per approved sample.
Incomings:
1 nos, 160 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of
fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect Digitally signed by AMIT
Bus Bars: SINGH
5 Date: 2024.08.27 16:02:05 IST
 TPN copper bus bars of minimum of 150 Amps capacity with heat shrinkable
colored sleeves and I/C DMC/SMC bus bars supports at required intervals
complete for cross section, size supports & their spacing etc. for withstanding fault
level of 25 MVA for 1 Sec.
Outgoings:
(A) 63 Amps, FP, RCCB - 8 nos
(B) 40 Amps, FP, RCCB - 8 nos
(C ) 32 Amps, FP RCCB - 4 nos
Panel complete as above
SAFETY ITEMS
Providing and fixing MV danger notice plate of 200mm x 150mm made of mild
17 2.21 steel, atleast 2 mm thick, and vitreos enamelled white on both sides and with Nos. 2 226.00 ₹ 452.00
iscription in single red colour on front side as required

Providing and fixing of wall mounted 24" dia fan including all fixing acceesories ,
18 MR Nos. 35 3961.00 ₹ 138,635.00
the motor should be thermal overload protection

Supply, Installation, Testing and Commissiong of 40 KVA True Online Double

Conversion UPS 3Phase Input - 3Phase Output in Parallel Redundant N+1
Configuration IGBT Based Rectifier and IGBT Based Inverter Batteries:12 V, SMF
Amararaja/Exide with minimum VAH capacity of 15600 suitable for 30 minutes
MR backup with each ups Along with Accessories Rack, stand, Interlinks, SFU, Parallel Each 2 840000.00 ₹ 1,680,000.00
Kit, DC Cable Upto 5 Meters, neccesary earthing setup and complete in all respect
as per the directions of the engineer in charge. UPS should have availability of
Input /Output isolator, Inbuilt manual bypass along with phase sequence corrector.
UPS Efficiency shall not be less than 94% from 25% to 100% Load
19

Supply, Installation, Testing and Commissiong of 4 KVA True Online Double

Conversion UPS 3Phase Input - 3Phase Output in Parallel Redundant N+1
Configuration IGBT Based Rectifier and IGBT Based Inverter Batteries:12 V, SMF
Amararaja/Exide with minimum VAH capacity of 15600 suitable for 30 minutes
MR backup with each ups Along with Accessories Rack, stand, Interlinks, SFU, Parallel Each 1 88000.00 ₹ 88,000.00
Kit, DC Cable Upto 5 Meters, neccesary earthing setup and complete in all respect
as per the directions of the engineer in charge. UPS should have availability of
Input /Output isolator, Inbuilt manual bypass along with phase sequence corrector.
UPS Efficiency shall not be less than 94% from 25% to 100% Load
20

Total ₹ 2,986,504.00 ₹ 3,622,425.00

Total of Electrical items ₹ 6,608,929.00

Digitally signed by AMIT

SINGH
6 Date: 2024.08.27 16:02:05 IST
 SCHEDULE OF QUANTITIES - HVAC WORKS
S NO DSR (E & M- DESCRIPTION TOTAL TOTAL
UNIT QTY RATE
2022)/ MR AMOUNT AMOUNT
DSR (INR) NON-DSR (INR)

Fire damper
Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch
and return air path as and where required of required sizes i/c control wiring,the damper
shall be motorized and spring return so as to close the damper in the event of power failure
automatically and open the same in case of power being restored. The spring return action
1.0 16.20
shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in
the event of fire signal complete as required and as per specifications.
(Fire damper shall ve suitable for 120 minutes fore rating as per NBC norms)

a 16.20.1 Fire damper SQM 0.5 10659.00 5329.50

b 16.20.2 Actuator NOS 1.0 9948.00 9948.00

GI Gravity Louver
2.0 M.R. Supply, installation, testing and commissioning of GI Gravity Louver complete with
neoperene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. SQM 0.5 6600.00 3300.00

3.0 VOLUME CONTROL DAMPER

Supply, Installation and Testing of GI box type volume control dampers as per the
M.R.
a specifications and shop drawings. SQM 2.0 5900.00 11800.00
- For Rectangular Ducts

Insulated Flexible Duct

Supply, Installation, Testing and Balancing of flexible ducting comprising of inner as well as
outer skin constructed out of aluminium & fibre glass insulation 25mm thick of minimum 24
kg/cu.m density insulation sandwitched in between. Duct should confirm to fire rating
standards BS-476 part 5, 6 & 7.
4.0 Flexible Ducts of following sizes as per approved shop drawings, specifications :
Universal (Jubilee) clamp should be provided to fix the flexible duct in the spigots/Butterfly
MR Dampers and covered with aluminium tape. Circular clip with chain/GI threaded rod to be
provided to support the flexible duct.

a 300 mm dia RMT 10.0 720.00 7200.00

b 250 mm dia RMT 10.0 550.00 5500.00
c 200 mm dia RMT 150.0 500.00 75000.00
d 150 mm dia RMT 10.0 460.00 4600.00

Supply, Installation and Testing of single piece GI round spigot made out of spinning
5.0 process with 50mm height and having grooves on both sides and circular flanges. Spigots
shall be installed on main ducts to facilitate connection of flexible ducts.

a MR 300 mm dia each 2.0 780.00 1560.00

1
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
S NO DSR (E & M- DESCRIPTION TOTAL TOTAL
UNIT QTY RATE
2022)/ MR AMOUNT AMOUNT
b 250 mm dia each 5.0 360.00 1800.00
c 200 mm dia each 5.0 310.00 1550.00
d 150 mm dia each 2.0 270.00 540.00

Supply, Installation and Testing of Butterfly damper of GI sheet construction with two flap
with round flange on one side and 10mm grove on other side for fixing of flexible duct with
6.0 the help of band, 20 Gauge Frame 250mm dia & above, 22 Gauge Frame upto 200mm dia
& 22 Gauge Blade in all sizes as per the specifications and shop drawings.
MR
a 300 mm dia each 2.0 780.00 1560.00
b 250 mm dia each 5.0 730.00 3650.00
c 200 mm dia each 5.0 680.00 3400.00
d 150 mm dia each 2.0 630.00 1260.00

DUCTING
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal
7.0 rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter
16.12.1 dampers, vanes, hangers, supports etc. as per approved drawings and specifications of
following sheet thickness complete as required.

a 16.12.1.1 Thickness 0.63 mm sheet SQM 20.0 1080.00 21600.00

b 16.12.1.2 Thickness 0.80 mm sheet SQM 10.0 1263.00 12630.00
c 16.12.1.3 Thickness 1.00 mm sheet SQM 10.0 1381.00 13810.00
d 16.12.1.4 Thickness 1.25 mm sheet SQM 10.0 1836.00 18360.00

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium
8.0 16.15 SQM 5.0 9105.00 45525.00
volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but
9.0 16.16 SQM 10.0 5910.00 59100.00
without volume control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium
10.0 16.17 SQM 5.0 12184.00 60920.00
with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium
11.0 16.18 without volume control dampers with anti smudge ring & removable core. SQM 5.0 8121.00 40605.00

Supply, Installation, Testing of antivibration flexible joints at the outlet of air handling
12.0 MR units/ductable split units//inline fans. Flexible connections shall be constructed using each 1.0 1440.00 1440.00
imported fire retardant fabric with extruded aluminium frame/flange on both sides of
approved make.
Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the SQM 0.5 5500.00 2750.00
13.0 MR suction of fresh air/discharge of Exhaust air as per the specifications and shop drawings.
Sample of bird screen to be got approved from consultants and Clients prior to procurement.
2
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
S NO DSR (E & M- DESCRIPTION TOTAL TOTAL
UNIT QTY RATE
2022)/ MR AMOUNT AMOUNT

INSULATION
Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed
cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for
14.0 16.23 Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive
nitrile rubber tape insulation complete as per specifications and as required.

16.23.1 19mm SQM 50.0 754.00 37700.00

ACOUSTIC

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin
bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm
15.0
16.21 thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm SQM 50.0 708.00 35400.00
thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts,
bolts, stick pins, CPRX compound etc. complete as required and as per specifications

Supply, Installation, Testing and Commissioning of Air Purification systems in the specified
areas where AHU/VRF/FCU/Cassette/Hi-Wall/Ductable units etc are installed, so as to
improve indoor air quality by using, Self-cleaning Needlepoint Ionizer made of Carbon brush
emitters. The Needlepoint brushes shall be designed to properly release equal amount of
positive and negative ions in the supply air,>400Million ions/cc without any obstruction. The
units to be suitable for following capacities with universal voltage input 24V to 240V AC/DC,
16.0 MR ionizer indicator LED, set of dry contacts which will indicate ionizer functionality. The unit
shall have capability to be switched on 24/7 .System should kill microorganisms and
pathogens and backed with Independent lab test reports on the real virus and not surrogate.
The system also should reduce odors, TVOC’s and reduce particle/particulate
matter/PM2.5/PM10. The products should be UL 2998 listed with zero Ozone Emission.

16.1 For Indoor Cassete unit from 1.6 TR to 4.0 TR Nos 16.0 16575.00 265200.00

17 2.5 GATE VALVES

Supply, Installation , Testing and Commissioning of following Gate Valves in accordance

with the approved shop drawings and specifications. Quoted price shall be inclusive of
insulation as per the specifications.
a. 40mm dia No 1 1,960.00 1,960.00
b. 32mm dia No 1 1450.00 1,450.00
c 25mm dia No 1 980.00 980.00

18 VRV SYSTEM

3
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
S NO DSR (E & M- DESCRIPTION TOTAL TOTAL
UNIT QTY RATE
2022)/ MR AMOUNT AMOUNT
Supply Installation, Testing & Commissioning of modular type Variable Refrigerant
Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,
having all hermetically sealed inverter type Scroll Compressor(s), minimum two
compressors for above 14 HP modules, microprocessor based Controller, top discharge
18 1 type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable per 96 16415.00 1575840.00
foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI HP
Conditions and work even at 50°C ambient temperature without tripping. The unit shall be
suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled
with first charge of the refrigerant and ready for use as required. The COP at AHRI
conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow
VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable
media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed
motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain
pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for
19 2
operation on
single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have
automatic force shut down provision in case of fire on receiving signal from BMS System.
The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19
Degree C WB temperature.
20 2.2 1 TR Each 12 29137.00 349644.00
20.1 2.4 1.6 TR Each 6 30204.00 181224.00
20.2 2.5 2.0 TR Each 7 30801.00 215607.00
20.3 2.6 2.4 TR Each 7 31453.00 220171.00
20.4 2.8 3.2 TR Each 9 32787.00 295083.00
20.5 2.10 4 TR Each 1 33981.00 33981.00

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T"
21 4 Joints i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

21.1 MR Y Joints NOS 42 4256.00 178752.00

21.2 MR Header NOS 4 8458.00 33832.00

Refrigerant Piping
Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen
testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF
22 5 system, complete with fittings, with suitable adjustable ring type hanger supports,
jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with
Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified
thickness as given below for Suction and Liquid lines, all accessories as per specifications
etc. as required :
22.1 5.1 6.4 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation M 60.00 245.00 14700.00
22.2 5.2 9.5 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation M 60.00 331.00 19860.00
22.3 5.3 12.7 mm
15.86 mmdia
dia(OD) (Soft/Hard
(OD) drawn)
(Soft/Hard with
drawn) tube
with thickness
tube 1.2
thickness mm
1.2 mmwith 1919
with mmmmthick insulation
thick M 75.00 466.00 34950.00
22.4 5.4 insulation M 60.00 588.00 35280.00
22.5 5.5 19 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 419 mm thick insulation M 50.00 707.00 35350.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
S NO DSR (E & M- DESCRIPTION TOTAL TOTAL
UNIT QTY RATE
2022)/ MR AMOUNT AMOUNT
22.6 5.6 22.2 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation M 25.00 865.00 21625.00
22.7 5.7 25.4 mm
28.58 mmdia
dia(OD)
(OD)(Soft/Hard
(Soft/Harddrawn)
drawn)with
withtube
tubethickness
thickness1.2
1.2mm
mmwith
with19
19mm
mmthick
thickinsulation M 10.00 1022.00 10220.00
22.8 5.8 insulation M 40.00 1108.00 44320.00
22.9 5.9 31.8 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation M 5.00 1170.00 5850.00
22.10 5.1 34.9 mm dia (OD) (Soft/Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation M 90.00 1230.00 110700.00
22.11 5.11 38.1
41.27mmmmdia
dia(OD)
(OD)(Soft/Hard
(Soft/Harddrawn)
drawn)with
withtube
tubethickness
thickness1.2
1.2mm
mmwith
with19
19mm
mmthick
thickinsulation M 90.00 1265.00 113850.00
22.12 5.12 insulation M 20.00 1309.00 1309.00
Cable/Wiring
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC
23 1.14
insulated copper conductor, single core cable in surface/ recessed medium class PVC
conduit as required.
23.1 1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Rm 50 233.00 11650.00
23.2 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Rm 150 275.00 41250.00
23.3 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Rm 150 334.00 50100.00
Supply , Installation and testing of control & transmission wiring of suitable size of VRV as
23.4 MR per site conditions on cable trays , conduits as required complete in all respects Rm 400 178.00 71200.00

24 Cable Trays with Covers

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray
(Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in
convenient sections, joined with connectors, suspended from the ceiling with G.I.
suspenders including G.I. bolts & nuts, etc. as required.
24.1 4.6.8 300 mm width X 62.5 mm depth X 2.0 mm thickness meter 50 1190.00 59500.00
24.2 4.6.10 450 mm width X 62.5 mm depth X 2.0 mm thickness meter 47 1574.00 73496.04

25 MR Drain Piping
Supply,installation,testing and commissioning of PVC drain water with necessary clamps,
fittings such as bends tees etc. and duly insulated.
32 mm dia (9 mm thickness insulation.) Rm 200 354.00 70800.00
40 mm dia (9 mm thickness insulation.) Rm 200 374.00 74800.00

26 MR Supply, Installation, Testing and Commissioning of Central Advance Intelligent Control

Manager with touch color LCD Display, Suitable for automatic control of all indoor units by
schedule function, troubleshooting, auto heat/cool changeover, temperature limitation, Each 1 115345.00 115345.00
history function, etc., complete as per technical specifications, capable of connecting upto
64 nos. indoor units as required.

Supply Installation testing & commisoining of following dia Heavy duty Exhaust fans Ceiling
MR
27 Mounted/ Wall Mounted Complete in All respects
150 mm PVC BODY Each 1 1800.00 1800.00
200 mm PVC BODY Each 1 2200.00 2200.00
300 mm PVC BODY Each 3 2800.00 8400.00
450 mm STEEL HEAVY DUTY Each 1 8500.00 8500.00
TOTAL HVAC WORKS 3468473.5 1410143.0
5
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
 TOTAL
TOTAL AMOUNT
S No DESCRIPTION UNIT QTY RATE AMOUNT
NON-DSR (INR)
DSR (INR)
CCTV
A. CCTV

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof

Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR
distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise
Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis,
IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video
1 Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Nos 10 ₹ 11,000.00 ₹ 110,000.00
Crossing line, Motion detection, Object left, Missing object,Intelligent Identification
Face detection, Defocus, Scene Change,PoE (IEEE802.3 af) Power consumption:
Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR Support,Working
Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible
Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 16 Ch Embedded Network

Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,
2 Nos 1 ₹ 55,723.00 ₹ 55,723.00
RAID, Redundant power supply, Smart Analytics
and ONVIF

SITC of Hard Disk Drive 10TB, 24/7 surveillance category Only complete etc as
3 Nos 2 ₹ 24,147.00 ₹ 48,294.00
required.etc.all complete.

Supply, Installation, Testing & Commissioning of 32" Flat Screen HD led (24X7) with
Interfaces include HDMI, DVI, D-sub, Component and Composite input as well as
4 RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / Nos 1 ₹ 32,659.00 ₹ 32,659.00
floor stand complete with making connections etc complete as reqd including 2 KVA
UPS Single Phase for Power Backup
5 SITC of HDMI cables 10 meters M2M etc all compelte. Nos 1 ₹ 1,857.00 ₹ 1,857.00
6 meter 200 ₹ 75.00 ₹ 15,000.00
Supply of Power Cum Communication cable for the above CCTV System
Total DSR + NDSR ₹ - ₹ 263,533.00
Grand Total ₹ 263,533.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 LIGHTING
Rate
SL NO DSR/MR Luminaire Description UOM QTY Rate( DSR) TOTAL AMOUNT
(Non DSR)
Supplying, fixing, connecting, testing and commissioning of 1x36-45 watt
LED light fixture suitable for 600x600 ceiling with electronic ballast, with
integral ballast, profiled diffuser, grey colored body , suitable mounts,
1 MR suspension cables complete as required, IP 40 rated, CRCA/ Aluminium no ₹ 80.00 ₹ 3,200.00 ₹ 256,000.00
housing.

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system
power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system
efficacy, Colour temperature of 4000 K, Neutral white, CRI > 80, 230V
constant current driver, 70% of luminous flux after 50,000 operating hours;
energy-efficient LEDs, direct light emission, housing in die-cast aluminium,
Polyester powder white coloured coat applied over a 5-stage pre-treatment
2 MR trim, prismatic diffuser for homogenous light distribution, ZHLS (ZERO no 150 ₹ 1,800.00 ₹ 270,000.00
HALOGEN LOW SMOKE) wiring, Electronic control gear,

Protection class II, IP 40,

Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm or its equivalent

Supply, Installation, Testing and Commissioing of Pendant luminaire with

LED (Light Emitting Diode), system power 28 W, luminous flux of luminaire
3080 lm, 110 LM/W system efficacy, direct light emission CRI>80, colour
temperature of 4000K, Neutral white, 230V constant current driver, 70% of
luminous flux after 50,000 operating hours, energy efficient LEDs, luminaire
profile in aluminium, Plastic moulded end caps, Polyester powder Aluminium
white coloured coat applied over a 5- stage pre-treatment, high efficiency
3 MR glare-free snap fit micro-prismatic diffuser for homogeneous light no 50 ₹ 7,500.00 ₹ 375,000.00
distribution, ZHLS (Zero Halogen Low Smoke) internal wiring, integral
Electronic control gear, adjustable suspender,

Protection class I, IP 20,

L = 1199 mm, B = 75 mm, H = 90 mm, PL max = 1500 mm

1 Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, Installation, Testing and Commissioing of Modular recessed luminaire with
HPE (High Performance Efficiency) LED (Light Emitting Diode), system power: 14W,
Luminous flux of luminaire 1540 lm, 120 LM/W system efficacy, colour temperature
of 4000 K, neutral white, CRI > 80, 230V constant current driver, 70% of luminous
flux after 50,000 operating hours, Energy efficient LEDs, Direct light emission,
Luminaire profile in aluminium, Polyester powder aluminium white coloured coat
applied over a 5- stage pre-treatment, Snap fit satin diffuser for a homogenous light
4 MR distribution ZHLS(ZERO HALOGEN LOW SMOKE) internal wiring, integral electronic
no 24 ₹ 5,500.00 ₹ 132,000.00
control gear,

Protection class I, IP 40, MacAdam 3, T.H.D ≤ 10%, driver efficiency ≥ 88%, surge
protection of 2.5kV, or its equivalent

L =1187 mm, B = 64 mm, H = 64 mm, L(ET) = 1175 mm, B(ET)= 52 mm.

Supply, Installation, Testing and Commissioing of recess type light fixture or
5 MR its equivalent Rm 28 ₹ 4,500.00 ₹ 126,000.00

Supply, Installation, Testing and Commissioing of Recessed downlight with

LED (Light Emitting Diode) system power: 8 W, Luminous flux of luminaire
640 lm, Colour temperature of 3000 K, Warm white, CRI > 80, 230V constant
current driver, 70% of luminous flux after 50,000 operating hours; energy-
efficient LED, direct light emission, housing in die-cast aluminium, Polyester
powder black coloured coat applied over a 5-stage pre-treatment ceiling trim,
6 MR with reflector, beam angle of 11-15°, electronic control gear, no 20 ₹ 1,600.00 ₹ 32,000.00

Protection class II, IP 20,

Ø = 60 mm, DA(ø) = 55 mm, H = 82 mm or its equivalent

Supply, Installation, Testing and Commissioing of LED strip Light fixture or

7 MR 120
its equivalent Rm ₹ 400.00 ₹ 48,000.00
DSR-
LIGHTING
CONTROL
Supply, Installation, Testing and Commissioing of Passive infrared (PIR)
technology based occupancy sensor having high performance, non regulating
programmable tupe, suitable for connected load up to 10 AMP, for mounting
8 15.1 height upto 2.8 mtr and for 5m diameter coverage area along with necessary no 15 ₹ 4,602.00 ₹ 69,030.00
fixing arrangements i/c programming at site etc. complete as required

TOTAL ₹ 1,308,030.00

2 Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 DSR (E & M -
SNO. DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT
2018) / MR
N0N -DSR ( INR
DSR ( INR )
)

Supplying & Fixing of battery operated illiminated "EXIT"

18 M.R. NOS 8 ₹ 3,870.00 ₹ 30,960.00
signage, with 2hrs power Battery backup complete as required.

21 Supply Installation Main Fire Alarm Panel Having Capacity to

integrate 1000 devices with 2 KVA 30 Min UPS, BMS
MR Integartion Module, Talk Back System Phone System, Nos 1 ₹ 266,500.00 ₹ 266,500.00
Intergartion with PA System, Addressable type,Complete in all
respects
Supply Installation testing & Commisioning 24 U Rack with
MR Power Sockets, Cable Cubbies, Cooling Fans etc for the Nos 1 ₹ 32,000.00 ₹ 32,000.00
above system Complete in all respects
TOTAL FIRE ALARM WORKS DSR +NDSR ₹ 1,260,056.00 ₹ 329,460.00

1
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
PROJECT : OFFICE INTERIORS FOR CGHS AT NEW DELHI
FIRE FIGHTING
TOTAL
TOTAL AMOUNT
S No DSR DESCRIPTION UNIT QTY RATE AMOUN
NON-DSR (INR)
T DSR
(INR)
1.0 FIRE EXTINGUISHER

Providing and fixing ISI Marked of approved make Fire

1.0 MR Extinguishers complete with all accessories as per
manufacturer's specifications.
1.1 MR a) CO2 gas nozzle type - 4.5 Litre capacity (IS:15683). NOS 6 ₹ 6,500.00 ₹ 39,000.00
1.2 MR b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). NOS 1 ₹ 3,228.00 ₹ 3,228.00

1.3 MR c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 10 ₹ 4,500.00 ₹ 45,000.00
Providing & fixing of clean agent gas based residue free stored
pressure FE-36 Dupont- HFC-236fa (HEXAFLUOROPROPANE
– CF3-CH2-CF3) multipurpose type having 0% ODP with
magnetic pressure gauge having the facility to check with the
magnetic pressure kit on site pressurised by dry nitrogen, can
2 MR height 341MM,
diamater is 108 MM Gross weight 3.6Kg, empty weight 1.6 Kg,
discharge time is minimum 6 sec, controllable discharge
machanisim, embossed fire rating as per the BS EN 3 - 21B, BIS
15683 marked with EPDM Hose with helium leak detection tested
2.1 and certificate
Capacity 5.0 kgenclosed, range 4 mtr
(ceiling mounted with plastic
for electrical yellow
& ups safety
room) NOS 2 ₹ 40,000.00 ₹ 80,000.00

3.0 NOVEC-1230 FOR SERVER ROOM

3.1 Supplying, installation, testing and commissioning of CCOE,
Nagpur approved, seamless storage cylinder meant for use in
MR NOVAC 1230 Gas suppression system ( Clean Agent ) Based
Fire Suppression System ( UL & FM Approved). The cylinder
shall be complete with:

1
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
 Bank of 1 Nos. (1 Operational + 1 stand by) 34Litre
Seamless Cylinders ( as per manufacture`s recommendation)
including the following:
a) Master discharge valves ( electrically operated resettable
type) & slave discharge valves ( Pneuomatically Operated)
b) Manual Actuation Device
c) Cylinder pressure monitoring system
d) Pressure guage with safety burst disc
e) Discharge flexible hose
f) Manifold with pressure switch
g)
h) Non-Return
Mounting rackValves
complete to be provided with MS brackets and
stand with duly painted.
i) Straps
j) Mounting Arrangements,Gas Filling, certification, testing ,
design Calculations, operation Manuals , Safety Kits
3.2 k) Safety Caps Set 1 ₹ 155,000.00 ₹ 155,000.00

4 Supply of Novec 1230 agent (Clean Agent Gas -UL & FM

MR Kg 50 ₹ 3,200.00 ₹ 160,000.00
Approved) including filling in the cylinder

4.1 Providing, fixing and testing Mild Steel Seamless pipes as per
ASTM A 106 Gr. B, Schedule-40 including necessary fittings and
MR accessories like tees, bends, elbows, unions, reducers, flanges,
gaskets etc. as required including fixing of pipework on walls,
slabs with supports, clamps etc. all complete Lot 1 ₹ 25,000.00 ₹ 25,000.00

4.2 Providing, calibrating and fixing Gas Discharge Nozzles, of

suitable dia designed to provide the proper flow rate &
MR
distribution of NOVEC 1230 to total flood a hazard area: 180
deg. / 360 deg Nos 3 ₹ 6,500.00 ₹ 19,500.00

4.5 Supply, installing, connecting up, testing and commissioning of

MR
the following fire alarm equipment :

2
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
 a) Single loop Analogue Addressable fire Alarm Panel:
Microprocessor based 1 loop analogue addressable type fire
alarm control panel with 80 character LCD display, four access
levels 500 event historcal logging, main power supply, battery
charger and maintenance free 24V baterry, Gas Release Control
Panel Module, an additional out put drive card/ monitor module to
facilitate networking with the Main Smoke Detector Panel/ BMS
Connectivity with RS485, all complete. with 1 KVA UPS Power
Supply. No. 1 ₹ 45,000.00 ₹ 45,000.00
a) Photo cum thermal (multicriteria) Smoke Detector with Nos 2 ₹ 3,800.00 ₹ 7,600.00
b) Addressable Manual call point No 1 ₹ 3,500.00 ₹ 3,500.00
c) Addressable loop powered Hooter Nos 2 ₹ 4,000.00 ₹ 8,000.00

4.6 Writing With Nos, alphabets (Enamel Paint) GAS

SUPPERSSION SYSTEM with capacity Complete in all respects No. 1 ₹ 1,500.00 ₹ 1,500.00
TOTAL for Server Room " carried over to SUMMARY ₹ - ₹ 592,328.00

Grand Total ₹ 592,328.00

3
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
 TOTAL TOTAL
DESCRIPTION UNIT QTY RATE AMOUNT DSR AMOUNT NON-
(INR) DSR (INR)

IT WORKS
A. UTP Components for Data
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the
1.53
existing surface/ recessed Steel/ PVC conduit as required.
1.53.1 1 run of cable Mtr 2500 ₹ 57.00 ₹ 142,500.00
1 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
130 ₹ 310.00 ₹ 40,300.00
at Work Station end. Keystone Unshielded Outlet, 180DG C6, Blue Nos.
2 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
at Work Station end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow 0 ₹ 310.00 ₹ -
Nos.
3 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
144 ₹ 310.00 ₹ 44,640.00
at Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue Nos.
4 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
at Rack Side end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow 0 ₹ 310.00 ₹ -
Nos.
5 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user device connectivity.High Speed Gigabit 24AWG 130 ₹ 260.00 ₹ 33,800.00
U/UTP Patch Cord Blue, LSZH, C6, 2M Nos.
6 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user device connectivity. (Rack end), High Speed 150 ₹ 260.00 ₹ 39,000.00
Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M Nos.
7 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user Redantant device connectivity.High Speed 0 ₹ 260.00 ₹ -
Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow) Nos.
8 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to Rack End Redantant device connectivity.High Speed 0 ₹ 260.00 ₹ -
Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow) Nos.
9 Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Staggred
6 ₹ 4,334.00 ₹ 26,004.00
Jack Panel for CAT6 cable termination at rack end. Data Active Nos.
UTP Components for VOICE
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the
1.53
existing surface/ recessed Steel/ PVC conduit as required.
1.53.1 1 run of cable Mtr 2500 ₹ 57.00 ₹ 142,500.00
10 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
125 ₹ 310.00 ₹ 38,750.00
at Work Station end. Keystone Unshielded Outlet, 180DG C6, (Ivory) Nos.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 11 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
₹ 310.00 ₹ -
at Rack end. Keystone Unshielded Outlet, 180DG C6, (Ivory) Nos.
12 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
at Rack End. Keystone Unshielded Outlet, 180DG C6, For Voice Active Riser Cable Nos. 144 ₹ 310.00 ₹ 44,640.00
(Ivory)
13 Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Staggred
Nos. 6.00 ₹ 4,334.00 ₹ 26,004.00
Jack Panel for CAT6 cable termination at rack end. Voice Active
14 Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled Staggred
Nos. 6.00 ₹ 4,334.00 ₹ 26,004.00
Jack Panel for CAT6 cable termination at rack end. Voice Active --- Riser Side
15 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user device connectivity. (Rack end), High Speed Nos. 150.00 ₹ 260.00 ₹ 39,000.00
Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M
16 Supply , Installtion , Testing and Comissioning of 4 Port British Style Shuttered Face
Nos. 130 ₹ 111.00 ₹ 14,430.00
Plate white for I/O fixing at user side

B. SERVER RACK and Accessories

1 SMART RACK 42U 800/1000D ,Perforated DOOR STEEL 800W 42U PRFFUL-4
Nos, CASTOR MED DTY FT BRAKE 100 KG - 1 No, EQUIPMENT SHELF
725MMD/600W - 3 Nos,KB TRAY ROTARY,19"/1000D+SLIDES 1 No,Fans Set of 4 Nos. 2 ₹ 42,584.00 ₹ 85,168.00
Nos Cable Managers, Hardware Fron Panel Etc complete as required as per site
requirement

C. 200 Pair MDF Box

1 200 Pair MDF Box with mounting Frame Powder Coated Box With Fans. Nos. 1 ₹ 32,586.00 ₹ 32,586.00
2 10 Pair Krone Module Nos. 15 ₹ 433.00 ₹ 6,495.00
3 25 Pair Riser Cable Mtr. 150 ₹ 223.00 ₹ 33,450.00

D UTP Components for Wifi

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the
1.53
existing surface/ recessed Steel/ PVC conduit as required.
1.53.1 1 run of cable Mtr 500 ₹ 57.00 ₹ 28,500.00
1 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
Nos. 18 ₹ 310.00 ₹ 5,580.00
at Work Station end. Keystone Unshielded Outlet, 180DG C6, White
2 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination
Nos. 18 ₹ 310.00 ₹ 5,580.00
at Rack end. Keystone Unshielded Outlet, 180DG C6, White
3 Supply , Installtion , Testing and Comissioning of 24 port Unloaded Angled Staggred
Nos. 1.00 ₹ 4,334.00 ₹ 4,334.00
Jack Panel for CAT6 cable termination at rack end. Voice Active
4 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user device connectivity. (Field End), High Speed Nos. 18.00 ₹ 260.00 ₹ 4,680.00
Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
5 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for
information outlet (I/O) to end user device connectivity. (Rack end), High Speed Nos. 18.00 ₹ 260.00 ₹ 4,680.00
Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M
6 Supply , Installtion , Testing and Comissioning of Single Port British Style Shuttered
Nos. 9 ₹ 111.00 ₹ 999.00
Face Plate white for I/O fixing at user side
F. Active Component for Data, Wifi

Supply, Installation, Testing & Commissioning of L3 Access Switch with SFP plus,
supporting 48-Port Layer 3 Stackable Managed Gigabit Switch, catalyst 9500
1 Nos. 1 315000.00 315000.00
24x1/10/25G and 4 port 40/100G advantage an 24-port 25/100 G advantage with 650
W power supply complete with all accesories Complete in all respects

SITC of 24 port 10/100/1000 Base T Switch with 4 x 10G SFP+ ports,The Switch
should have 16K MAC/IP address, Should have RJ-45 console port should support
MSTP and DUAL configuration, Should support Static Route Entry: IPv4 124; IPv6 50
2 , Should support IP-MAC- Port Binding strictly management network devices Nos. 2 218000.00 436000.00
preventing illegal access and the Man-in- the-middle attack, Should support
Asymmetric VLAN, Auto Voice VLAN, Should support Cable diagnostics, Timebased
PoE: PoE ports can be turned on/off by port or system through schedule, Operating
Temperature -5 to 50°C (23 to 122°F).

SITC of Wifi router 10G compatible with ethernet port 6 GHz 5400mbps dual core one
3 Nos. 4 18000.00 72000.00
mesh supported wireless 6E wi fi router archer AXE75 including 5 amps power
socket, IO, pvc box etc mounting arrangement & wifi mapping complete in all respect
SITC of 6mode opticle fibre cable including laying the same in pvc conduit, HDPE
4 pipe as required at site cost include cost of cable & conduit inclduing splicing kits, Mtr 300 40.00 12000.00
connection etc complete in all respects
5 Providing and laying of LC- LC multimode OFC type patch cord for data and voice. Nos. 6 3850.00 23100.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, Installation, Testing and comissioning of Firewall . Supply, Installation,
Testing and comissioning of Firewall. The UTM solution should be Hardware based,
Reliable, purpose-built security appliance with hardened operating system that
eliminates the security risks associated with general-purpose operating systems. The
Xstream Deep-Packet Inspection (DPI) engine provides high-performance traffic
scanning for IPS, AV, Web Protection, and App Control in a single streaming engine.
6 Firewall throughput should be 33 Gbps or above, IPS throughput should be 6.5 Gbps, Nos. 1 320000.00 320000.00
Threat Protection throughput 1.2 Gbps Concurrent connections 6 Million, New
connections/sec 140,000. Should support TLS 1.3 inspection, Next-Gen Intrusion
Prevention (IPS), Zero-day threat protection, Proxy-based dual-engine AV scanning,
TLS 1.3 without downgrading, Intelligent traffic selection, Cloud Sandbox/ ATP,
Advanced Web Protection, Advanced Threat Protection, Web caching. Storage
(local quarantine/logs)-Integrated min. 240 GB SATA-III SSD, Ethernet interfaces
(fixed)- 8 x GE copper, 2 x SFP fiber*, 2 x SFP+ 10 GbE fiber*, Bypass port pairs- 1,
Management ports- 1 x RJ45 MGMT, 1 x COM RJ45, 1 x Micro-USB (cable incl.).

Supply, Installation, Testing & Commissioning of Server based Communication

System with all the required Software licenses and Hardware - IP-PBX/IP Telephony
Communications Server: The IP Telephony Solution shall support the following
Services - Voice, Video, IM, Presence and Audio Conference The Solution should be
7 built on Active-Redundant Servers The IP Telephony Solution should support H.323 Nos. 1 275000.00 275000.00
and SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP
The IP Telephony solution should incorporate all licenses for the Phones and Trunks
Solution should support 100 Extensions from Day 1 with future scalabilityupto 1000
users. Licenses for all Phones supplied should be provisioned on Day1 Solution
should support Hard IP Phones, Softphones, Video Phones, 50 Analog Extensions
with necessary Licenses, Rack mount architecture, complete as required and as per
technical specifications.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, Installation,Testing and commisioning of Executive Level IP Phone with Color
display – 3.7 inches x 2.1 inches (9.5 cm x 5.4 cm)- Diagonal width: 4.3 inches (11
cm), Touch Screen display, 4-position adjustable tilt display, Permanently-labeled
feature buttons:, speaker, mute, headset, contacts, home, history, message, phone,
forwarding, volume (separate volume levels in handset, speaker, ringer, and
headset), Red LEDs on speaker, mute, headset, message and history, 24
administrative buttons, Wideband speakerphone 0-5 Softkeys, Ergonomic hearing
Nos. 6 12500.00 75000.00
aid compatible, handset supporting TTD acoustic coupler, Bluetooth and DECT
headset support with adapter, Message waiting indicator, Ethernet (10/100/1000)
line interface, Secondary Ethernet (10/100/1000)line interface, Optional IEEE PoE
802.3af adapter registers as class 2 device, SIP protocol, H.323 protocol support,
Standards-based codec support: G.711, G.726, G.729A/B, G722 , Supports the
following languages: Arabic, Brazilian Portuguese, Simplified, Chinese, Dutch,
English, Canadian,French, Parisian French, German,Hebrew, Italian, Japanese
(Kanji,Hiragana and Katakana), Korean, Latin American Spanish, Castilian Spanish,
8 and Russian. Includ Licence.
Supply Installation testing & commisoing of IP Phones for Officers with, Digital Calling
, LED Panels, Builtin Speaker Superior Quality Phone Nos. 30 1800.00 54000.00
9
Total ₹ 313,500.00 ₹ 2,138,224.00
Total DSR & NDSR ₹ 2,451,724.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Audio visual system
Board Room
S No. Description Qty Unit Rate Total DSR Total NDSR
Supply, installation, testing and commissiong of 1*4 distribution amplifier with Automatic
down-conversion on the output from 4k to 1080p if required by the connected HDMI
display, Advanced EDID Management,CEC support (pass-through),HDMI 2.0 signal
support,Input cable equalization,Compact size,Support for all HDMI 2.0 embedded
audio formats,Mounting ears for easy fixture,EDID emulation of factory EDIDs, EDIDs
1 read dynamically from the outputs, or custom EDID stored in memory,3D pass-through 1 Nos 83,300.00 ₹ 83,300.00
support,EDID emulation in transmitter, HDCP enable/disable function on input,No signal
latency, zero frame delay, Firmware upgrade through USB all complete.

Supply, installation, testing and commissiong of HDMI transmiter which can be remote
powered through CATx cable (12V),Supports HDMI 3D signal formats ,Supports deep
color signals (24/30/36 bit RGB/YCbCr 4:4:4),1920x1080@120Hz/4:4:4,
4096x2160@30Hz/4:4:4 or 60Hz/4:2:0 maximum resolutions (300MHz),Supports all
VESA and HDTV resolutions,HDMI 1.4, HDCP 1.4 and DVI 1.0 compliant,Bi-directional
RS-232 extension (pass-through),HDCP 2.2 compliant (transparent pass-
through),Compatible with 120 Hz 3D video signals,Uncompressed video up to 9 Gbps
datarate,No signal latency, zero frame delay,Selectable operation mode (Auto or forced
Long Reach mode)Cross compatible with TPS series Lightware extenders and I/O
boards (HDBaseT compatible),Supports all embedded audio formats (including PCM,
Dolby Digital and DTS high bitrate audio).Extension distance up to 170 meters (with
2 1 Nos 172,550.00 ₹ 172,550.00
CAT7 S/FTP AWG23 cable, 1920x1080p60),HDBaseT compatible,Transparent EDID
pass-through,Bi-directional IR extension (pass-through),CEC support (pass-
through),Supports HDMI 4K signal formats (4K UHD @30Hz RGB 4:4:4 or @60Hz YUV
4:2:0, up to 9 Gbps),No video compression,Bi-directional RS-232 and IR extension
(pass-through),Status LEDs (Live, TPS link, signal and HDCP detect),Twist-and-lock DC
power connector,Low power mode (standby),Local or remote (remote-send / remote-
receive) power source,External universal power adaptor all complete.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, installation, testing and commissiong of HDMI receiver which can be remote
powered through CATx cable (PoE PD), Supports HDMI 3D signal formats (frame
packing, side-by-side and top-bottom), Supports deep color signals (24/30/36 bit
RGB/YCbCr 4:4:4), 1920x1080@120Hz/4:4:4, 4096x2160@30Hz/4:4:4 or 60Hz/4:2:0
maximum resolutions (300MHz), Supports all VESA and HDTV resolutions, HDMI 1.4,
HDCP 1.4 and DVI 1.0 compliant, Bi-directional RS-232 extension (pass-through),
HDCP 2.2 compliant (transparent pass-through), Compatible with 120 Hz 3D video
signals, Uncompressed video up to 9 Gbps datarate (300 MHz pixel clock), No signal
latency, zero frame delay, Selectable operation mode (Auto or forced Long Reach
mode), Cross compatible with TPS series Lightware extenders and I/O boards
3 (HDBaseT compatible), Supports all embedded audio formats (including PCM, Dolby 1 Nos 132,600.00 ₹ 132,600.00
Digital and DTS high bitrate audio), Extension distance up to 170 meters (with CAT7
S/FTP AWG23 cable, 1920x1080p60), HDBaseT compatible, Ethernet extension (100
Mbps), Selectable IR output mode for emitter or wired connectivity, Transparent EDID
pass-through, Bi-directional IR extension (pass-through), CEC support (pass-through),
Supports HDMI 4K signal formats (4K UHD @30Hz RGB 4:4:4 or @60Hz YUV 4:2:0, up
to 9 Gbps), No video compression etc all complete.

Supply, installation, testing and commissiong of delegate unit with network based
architechture, Crystal-clear sound due to a very high signal-to-noise ratio, Maximum
speech intelligibility is guaranteed, The loudspeaker and microphone can be active at
the same time to facilitate a face-to-face meeting experience. A feedback suppressor is
built in to prevent acoustic feedback, OLED screen, inbuilt loudspeaker, Enables
participants to speak and listen to the proceedings, Operates as stand-alone discussion
system or connects to external AV equipment or videoconferencing system, Headphone
socket with built-in volume control, Line-in interface to connect device to the ongoing
4 conference, A 48-bit digital audio signal is transported to each discussion unit for real- 18 Nos 23,650.00 ₹ 425,700.00
time monitoring from the loudspeaker, GSM immune, Built-in loudspeaker, the unit
should show time/date on the screen. Should have timer on display to set for each
delegate to speak, should have touchable button interface, Sensitivity: -46 dBV / Pa,
Directivity: 0 ° / 170 °> 20 dB (1 kHz), Headphone load: 16Ω, Input impedance: 2kΩ,
signal to noise ratio: 70dB, Frequency response: 20 ~ 20000Hz, should have hot swap
functionality.Bidder should provide bid specific OEM authorization etc all complete.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, installation, testing and commissiong of chairman unit with priority and network
based architechture, Crystal-clear sound due to a very high signal-to-noise ratio,
Maximum speech intelligibility is guaranteed, The loudspeaker and microphone can be
active at the same time to facilitate a face-to-face meeting experience. A feedback
suppressor is built in to prevent acoustic feedback, OLED screen, inbuilt loudspeaker,
Enables participants to speak and listen to the proceedings, Operates as stand-alone
discussion system or connects to external AV equipment or videoconferencing system,
Headphone socket with built-in volume control, Line-in interface to connect device to the
5 ongoing conference, A 48-bit digital audio signal is transported to each discussion unit 1 Nos 24,650.00 ₹ 24,650.00
for real-time monitoring from the loudspeaker, GSM immune, Built-in loudspeaker, the
unit should show time/date on the screen. Should have timer on display to set for each
delegate to speak, should have touchable button interface, Sensitivity: -46 dBV / Pa,
Directivity: 0 ° / 170 °> 20 dB (1 kHz), Headphone load: 16Ω, Input impedance: 2kΩ,
signal to noise ratio: 70dB, Frequency response: 20 ~ 20000Hz, should have hot swap
functionality etc all complete

Supply, installation, testing and commissiong of digital discussion central controller,

should expand up to 2500 or more discussion devices and easily connected to audio
system, with short-circuit protection, freestanding or 19” rack mounted, transmit upto 64
channels of audio, 48K audio sampling rate and 20Hz ~20KHz frequency response,
sensitivity of the microphone and 8 segment equalizer EQ should be adjusted
independently, should have 16 segment equalized EQ, AGC, AEC, AFC, USB
recording, should have atlesat 4 dante output ports, shoudl have TCP/IP connection for
6 software server and controller, RS232 for control, RS232 or RS485 to achieve look at 1 Nos 160,650.00 ₹ 160,650.00
me functionality, Hot plug-and-play, shoudl have voting functionality, should have LCD
display on controller to show all functions, should have 3.5mm headphone for
monitoring, 2 audio input ports, 1x RCA, 1x XLR and atleast 5 audio output ports, atleast
3 ports for conneciton of loops or series connection, (S / N) >97dBA, Total harmonic
distortion <0.05%, Channel Crosstalk> 84dB, Dynamic range >93dB etc all complete
Approved makes: Brahler/Bronx/Bosch
Supply, installation , testing & commissioning of 30x optical zoom PTZ camera with SDI,
HDMI, RJ45, RS232/RS485 connectors, should be compatible witht the wirless
7 conference controller to enable look at me feature, should have BIS, CE, FCC, ROHS, 2 Nos 180,960.00 ₹ 361,920.00
should be supplied with mounts as per site requirement etc all complete
Supply, installation , testing & commissioning of camera switcher and mixer with atlease
6 video input ports with 2 HDMI and 4 SDI ports, suystem should have capability to do
PIP and PBP output, shoudl have one HDMI output with parellel local monitor output,
should have RS232 port for integration with thirdparty devices, should have audio and
8 video bridging builtin the system through USB passthrough for integration with all cloud 1 Nos 198,900.00 ₹ 198,900.00
based video conferencing solutions, should have audio input,
1280x720@50Hz;1280x720@60Hz; 1920x1080@25Hz; 1920x1080@30Hz, bidder to
submit bid specific OEM authorization etc all complete

Supply, installation , testing & commissioning of Ceiling Speaker - 8" / 7.5&15W,

Power(RMS):7.5W/15W, Impedance: 8 ohms , Line Voltage: 70V/100V AC, Frequency
9 10 Nos 2,465.00 ₹ 24,650.00
Response: 85Hz-17KHz, Sensitivity(1w/1m): 91dB, Speaker unit: 8" (203mm) , Cutout
Dimension: Φ 220mm, Over Dimension: Φ 250*75mm

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, installation , testing & commissioning of Mixing Amplifier-250W, Built-in MP3
player and FM tuner and remote control, MP3 Player with USB,SD port and fluorescent
screen to display the sound number, Four function buttons: previous, play/stop, next and
10 mode, 70V,100V and low impedance 4-16 ohms speaker output, 5 zone and all zone 1 Nos 26,826.00 ₹ 26,826.00
speaker outputs, Three Mic input by phone jack type, AUX 1-3, Mic 1-3 volume controls
and bass/treble tone control, High temp, overload and short-circuit protection
Supply, installation , testing & commissioning of 24U rack Approved
11 1 Nos 24,225.00 ₹ 24,225.00
Supply, installation , testing & commissioning of speaker cable 1.5sqmm 2 cose etc
12 including conduiting,casing caping, chase cutting at site complete in all respect 300 Meter 80.00 ₹ 24,000.00

Supply, installation , testing & commissioning of UTP Cat6 cable in 25mm conduit etc
13 including conduiting,casing caping, chase cutting at site complete in all respect 600 Meter 75.00 ₹ 45,000.00

Supply, installation , testing & commissioning of 15 meter HDMI cable etc including
14 conduiting,casing caping, chase cutting at site complete in all respect 4 Nos 4,500.00 ₹ 18,000.00

Supply, installation , testing & commissioning of 1.5 meter HDMI cable etc including
15 conduiting,casing caping, chase cutting at site complete in all respect 5 Nos 2,300.00 ₹ 11,500.00

Supply, installation , testing & commissioning of 23Awg or better microphone cable etc
16 including conduiting,casing caping, chase cutting at site complete in all respect 50 Meter 99.00 ₹ 4,950.00

Supply, installation , testing & commissioning of 42U equipment rack etc

17 1 Nos 32,560.00 ₹ 32,560.00

Supply, installation, testing and commissiong of All-in-one design video conferencing

bar The three-in-one design of 4K ultra HD camera, beam-forming microphone and full-
frequency loudspeaker reduces wiring and makes video communication easy, 4K UHD
Using 1/2.5 inch, 8.51M pixel high quality UHD CMOS sensor, 4K (3840x2160) @ 60fps
ultra high resolution clear image, and downward compatible with 1080P, 720P and other
resolutions. Can meet the needs of users for different video experiences, and can
provide clear, real, smooth and accurate communication, Wide FoV 120°wide field of
view (110° horizontal field of view), 5 times zoom, optical lens customized for the
conference scene, builtin electric head (horizontal and pitch ±15° motion range), no
need to worry about the camera position, participants can easily enter the scene clearly,
Beam Forming (BF) microphone is built in, with a pickup distance of 6 meters. Low-
distortion transverse beam-forming algorithm can direct the microphone directly to the
18 speaker, with better sound, clearer communication, fuller and more authentic.Built-in 1 Nos 130900.00 ₹ 130,900.00
audio 3A algorithm (AEC/AGC/ANS), full duplex dialogue, can meet the communication
needs of different room structures, whether sitting at a conference table, sitting against
the wall or standing, can have comfortable experience for calling, Full frequency speaker
Full frequency Hi-Fi loudspeaker, professional acoustics design, reduce noise
interference, provide outstanding sound effect, Plug and play type Through plug and
play USB interface connect with the computer or business display screen, very easy to
use. Less wiring, convenient video communication, reduce the user's learning cost, Built-
in intelligent analysis algorithm, listening to the speaker position, automatic framing of
participants, automatic tracking of speakers, switching the speaker screen, to ensure
that the speaker is always clearly in the picture, Rich interfaces Support HDMI 2.0 and
USB 3.0 audio video output simultaneously, Easy installation etc all complete.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Supply, installation , testing & commissioning of 15 meter HDMI cable etc including
19 conduiting,casing caping, chase cutting at site complete in all respect 1 Nos 4,500.00 ₹ 4,500.00

Supply, installation , testing & commissioning of USB 3.0 Extention cable 10 meter etc
20 including conduiting,casing caping, chase cutting at site complete in all respect 1 Nos 9000.00 ₹ 9,000.00

₹ -

Supply, installation, testing and commissiong of Diagnol size 54.6" /

138.7cm 4k LED TV, Resolution 3840x2160(16:9), Brightness(Typ.) 700 nit,
Orientation Landscape / Portrait , Contrast Ratio (Typ.) 4000:1, Haze Non-
Glare, Type VA, Active Display Area 1209.6(H) x 680.4(V) , Pixel Pitch (mm)
0.315 x 0.315, Color Gamut 92% (DCI-P3, CIE 1976), Operation Hour 24/7,
INPUT VIDEO DP 1.2 (1), HDMI 2.0 (3), INPUT AUDIO N/A, INPUT USB USB
2.0 x 2, OUTPUT VIDEO N/A , OUTPUT AUDIO Stereo mini Jack, OUTPUT USB
22 10 Nos 82450.00 ₹ 824,500.00
N/A, WiFi / BT O / O, EXTERNAL CONTROL RS232C(in/out), RJ45, Speaker
10W 2ch, Dimension(mm) Set 1235.1 x 707.9 x 46.3, Operating System
Tizen 6.5, Storage 16 GB, Processor Cortex A72 1.7GHz Quad-Core CPU,
Safety 60950-1 / 62368-1, EMC Class B, IP Rating IP5x, Security
802.1x(WPA2 Enterprise) : EAP-TLS, EAP-TTLS, EAP-PEAP, Power Supply AC
100 - 240 V, 50/60 Hz, Temperature 0℃~ 40℃, Relative Humidity 10~80%,
etc all complete.

SITC of 43''4k LED TV diagonal size , resolution 3840*2160( 16:9), bightness

700 nit,haze - non glare, active display size 941.84(H)*529.416(V), Pixel
pitch(mm)- 0.2451* 0.2451, color gamut 92%(DCI-P3,CIE1976), operating
23 system tizen 6.5, processor Cortex A72 1.7GHz, Quad-Core CPU ,Storge 7 Nos 56950.00 ₹ 398,650.00
(FDM) 16GB,Safety 60950-1 / 62368-1,input DP 1.2 (1), HDMI 2.0 (3), USB
2.0 x 2, output Stereo mini jack ,EXTERNAL CONTROL RS232C(in/out), RJ45
port , Speaker 10W 2ch, IP Rating ,IP5,Operation hour 24/7

Supply, installation, testing and commissiong of 75'' diagonal size , 4k LED

TV resolution 3840*2160( 16:9), Contrast Ratio (Typ.) 6000:1,bightness 700
nit,haze - non glare, active display size 1650.24 (H) x 928.26 (V), Pixel
pitch(mm)- 0.42975* 0.42975, color gamut 92%(DCI-P3,CIE1976),
24 operating system tizen 6.5, processor Cortex A72 1.7GHz Quad-Core CPU 1 Nos 195500.00 ₹ 195,500.00
,Storge (FDM) 16GB,Safety 60950-1 / 62368-1,input DP 1.2 (1), HDMI 2.0
(3), USB 2.0 x 2, output Stereo mini jack ,EXTERNAL CONTROL
RS232C(in/out), RJ45 port , Speaker 10W 2ch, IP Rating ,IP5,Operation hour
24/7, ,etc all complete.

ZBOOK POWER G8, 50U12PA, i7-11800H, 16GB (1x16GB) DDR4, 1TB SSD,
25 32 Nos ₹ 155,216.00 ₹ 4,966,912.00
NVIDIA Quadro T600 4GB, Win11 Pro, 15.6'' FHD AG, 250nits, 3yr Onsite,

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 LG 65TR3DJ
Brightness : 390 nit (w/o Glass, Typ.) Multi Touch Point : 20 Points (Max.)
Interface : HDMI (3), RGB (1), Audio In (1), RS-232C In (1), RJ45 (1), USB
3.0 Type A
(3), USB 2.0 Type A (3), Audio Out / Optical Output, Touch USB (2), Screen
Size : 65"
Panel Technology : IPS Aspect Ratio : 16 : 9
Native Resolution : 3,840 x 2,160 (UHD)
26 3 Nos ₹ 153,742.20 ₹ 461,226.60
Brightness : w/o Glass : 490 nit (Max.), 390 nit (Typ.) w/ Glass : 450 nit
(Max.), 350 nit (Typ.)
Contrast Ratio : 1,200:1
Viewing Angle (H x V) : 178 x 178 Response Time : 8ms (G to G) Life Time
(Typ.) : 30,000 Hrs (Min.)
Operation Hours (Hours / Days) : 16/7
Portrait / Landscape : Landscape

27 Bronx Wall Mount for 65" Display 3 Nos 20498.96 ₹ 61,496.88

Total DSR + NDSR Grand total ₹ - ₹ 8,824,666.48

Total ₹ 8,824,666.48

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 MODULAR FURNITURE BOQ
Total
S.No. Specification unit Rate In Rs Amount
Qty.
Modular Furniture
1 Officer Cabin Table
Main Table Dimension : 1500mm(L) X 750mm(D) X 750mm(H)
5 nos ₹ 73,000.00 ₹ 365,000.00
Overall Side Unit Dimension : 1500mm(L) X 450mm(D) x 750mm(H)

Supplying, and placing in position of main Table as per drawing/image. The Table top are made out of
25mm thk prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel are made
up of 18mm thick pre-laminated particle board .The working edges shall be provided with machine pressed
2mm thick PVC edging using special hot melt glue at hot temperature. The table have a provision of Side
Storage, Storage Top are made out of 25mm thick pre laminated particle board and rest all storage to be
made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine
pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Side Storage having a provision of 3
drawer unit of size: 400mm(L) x 450mm(D) x 675mm(H) attached to the side storage top with the help of
shiny metal rods. Pedestal Unit have a combination of 2 drawer & one filing drawer. The pedestal storage
unit shall be made of 18 mm thick prelaminated Particle board with provision of central Locking
arrangement. The table shall be provisioned with back storage. The back storage unit having Openable
shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-laminated
particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-
laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be
provided with 2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles &
locking arrangement.The product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
S.No. Specification unit Rate In Rs Amount
Qty.
2 Officer Cabin Table
Main Table Dimension : 1700mm(L) X 750mm(D) X 750mm(H)
7 nos ₹ 88,904.00 ₹ 622,328.00
Overall Side Unit Dimension : 1500mm(L) X 450mm(D) x 750mm(H)

Supplying, and placing in position of main Table as per drawing/image. The Table top are made out of
25mm thk prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel are made
up of 18mm thick pre-laminated particle board .The working edges shall be provided with machine pressed
2mm thick PVC edging using special hot melt glue at hot temperature. The table have a provision of Side
Storage. Storage Top are made out of 25mm thick pre laminated particle board and rest all storage to be
made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine
pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Side Storage having a provision of 3
drawer unit of size: 400mm(L) x 450mm(D) x 675mm(H) attached to the side storage top with the help of
shiny metal rods. Pedestal Unit have a combination of 2 drawer & one filing drawer. The pedestal storage
unit shall be made of 18 mm thick prelaminated Particle board with provision of central Locking
arrangement. The product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

3 Clerk Table
Main Table Dimension : 1500mm(L) X 600mm(D) X 750mm(H)
1 nos ₹ 50,800.00 ₹ 50,800.00
Overall Side Unit Dimension : 900mm(L) X 450mm(D) x 750mm(H)

Supplying, and placing in position of table as per drawing. Table top made up of 25mm thick pre-
laminated particle board and understructure shall be made of 18mm thick prelaminated particle board
gable ends and modesty panels. The working edges shall be provided with machine pressed 2mm thick
PVC edging using special hot melt glue at hot temperature. Provision of 3 drawer mobile pedestal, one
CPU trolley and PVC keyboard tray attached to the table top. The table shall be provisioned with free
standing. Storage Top made out of 25mm thick pre laminated particle board and rest all storage to be
made out of 18 mm thick prelaminated particle board . Storage having a openable shutter with handles
and central locking arrangement. All exposed edges shall be provided with machine pressed 2 mm thick
PVC lipping glued with hot melt EVA glue. The product should be from the manufacture which have BIFMA
membership Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX
Certification. The product should be as per above given specification under the guidance of Engineer in
charge.

4 Medium Height Storage

Dimension: 1350mm(L) X 450mm(D) x 1200mm(H) Digitally signed by AMIT
SINGH 6 nos ₹ 39,600.00 ₹ 237,600.00
Date: 2024.08.27 16:02:05 IST
 Total
S.No. Specification unit Rate In Rs Amount
Qty.

Supplying, and placing in position of medium height storage @ 1200mm height as per photograph/drawing
. The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made
from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be
made up of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated
particle board. All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable
shutters withD shape handles & locking arrangement.The product should be from the manufacture which
have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification,
SEDEX Certification. The product should be as per above given specification under the guidance of
Engineer in charge.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
S.No. Specification unit Rate In Rs Amount
Qty.
5 Reception Table
Dimension: 2400mm(L) X 900mm(D) x 1050mm(H) 1 nos ₹ 137,525.00 ₹ 137,525.00

Supplying & placing in position of modern design reception desk in engineered wood make the products
utile and a delight. Timeless design that elevates your office space structure of spacious reception desk,
table top offers you a generous look for work surface use premium quality materials overall size is 2400
mm (l) x 900 mm (d) x 750 mm (h) which give more surface area for work, table top made of 25mm thick
also table top based on side panel's made 18mm thick prelaminated particle board of grade ii type iii of is
12823/latest. Combination construction of reception desk above table top 18 mm thick counter top to table
top height is @ 300mm, overall reception desk height is @ 1050mm with counter top, table top made 25
mm thick prelam particle board work surface with the exposed edges shall be finished with 2mm thick pvc
edge binding tape of matching colour and shade fixed with hot melt glue. Along with 18mm thk additional
modesty panel size is 1800 mm (l) x 700 mm (h) made by exclusive frosty white colour with epic design &
look.1 mobile pedestal (2 drawers + 1 filing cabinet) size is 450 mm (l) x 450 mm (d) x 725 mm (h) in
provided with central lock's for security and handles are provided for easy of opening & pedestal's move on
nylon castors.The product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

6 Credenza for VIP Waiting area

Dimension (W)1500mm X (D)400mm X (H)750mm 1 nos ₹ 72,600.00 ₹ 72,600.00

Supplying & placing in position of credenza as per image. A classic mid-century-inspired design wrapped
in exotic veneer makes Eero buffet a statement piece. The tabletop stuns with its mesmerizing herringbone
pattern, masterfully crafted by skilled Marquetry artisans. Perching on solid wood legs, this buffet elegantly
stores your dining essentials.Material & Subtype Engineered Wood - MDF,Solid Wood - Beech
Wood,Veneer - Steam Beech Veneer,Table Top Material Veneer,Frame Material Engineered Wood, Leg
Material Solid Wood
Finish Matte,Colour & Colour Family Brown - Walnut.The product should be from the manufacture which
have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification,
SEDEX Certification. The product should be as per above given specification under the guidance of
Engineer in charge.

7 Mobile Pedestal
Dimension (W) 400mm X (D) 450mm X (H) 600mm 84 nos ₹ 14,763.00 ₹ 1,240,092.00
Digitally signed by AMIT
SINGH
Date: 2024.08.27 16:02:05 IST
 Total
S.No. Specification unit Rate In Rs Amount
Qty.

Supply & Placing on position of mobile pedestal Unit of size:- L-400mm x D-450mm x H-600mm as per
image . Pedestal with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be
made of 18 mm thick prelaminated Particle board with provision of handles & Locking arrangement. The
product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
S.No. Specification unit Rate In Rs Amount
Qty.
8 Workstations Modifications work
Dimension (W)1350mm X (D)1350mm X (H)750mm 84 nos ₹ 13,500.00 ₹ 1,338,120.00

Minor modification work of all the workstaions like Fabric change and edge bending repairing.

9 Medium Height Storage locks & Hardware replacement

Dimension(L)2650mm X (W)400mm X (H)1200mm 20 nos ₹ 3,550.00 ₹ 459,200.00

10 Podium for Board room

Dimension(L)550mm X (W)550mm X (H)1200mm 2 nos ₹ 68,700.00 ₹ 137,400.00

Supplying and placing in position of adjustable height podium as per image/drawing.This heavy duty
adjustable lectern promotes better posture, reduced back and neck pain, making teaching or presenting a
healthy breeze. Podium adjusts to the working height , adjustment from 40.5" - 48.5" high.The silver gray
powder coat paint finish and wood laminate shelves are heavy duty ensuring years of use.The presenter's
shelf is at a 17 degree angle with a paper stopper that keeps your documents neat and organized.Moving
the lectern from room to room is easy with the 2" furniture casters (two casters have locking brake).The
product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

Total Amount Including GST@18% In Rs= ₹ 4,660,665.00

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 LOOSE FURNITURE BOQ
Total
Rate
S.No. Specification unit Amount
In Rs
Qty.
Loose Furniture
1 Sofa for VIP Waiting area
3 seater Dimesnion: (W)1800mm X (D)710mm X (H)770mm 1 nos 86200.00 86200
2 seater Dimesnion: (W)1530mm X (D)710mm X (H)770mm 1 nos 69200.00 69200

Supplying and placing in position of exclusive premium leatherette modernist classic design lounge seating sofa
with kiln-dried wood framing makes it warp and scratch resistant, comfortable seat depth & height designed
keeping modern Indian lifestyle in mind, wrapped in buttery-soft premium leatherette, the panelled back and
cushioned armrests encourage lounging, designed with modernity & elegance, choose the option that suits your
home. Combination construction structure are made in moisture content shall be less than (10-12)%. Thickness
of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture
proof plywood (tentative).under structure frame shall be constructed from 18 mm thick kiln-dried German
beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive
glue, the frame shall be padded with high resilience polyurethane foam having 28 +/- 5 density in seat it shall
be stack foam of 50mm thik, 40mm thick back foam having 20 +/- 5 density foam used ,there shall be cushion
arm 10mm thick provided padded with high resilience polyurethane foam having density 32 +/- 5. The
complete stack foam structure shall be covered with premium leatherette in premium leatherette with solid
wood colour, it complements the modish solid wood legs.( seat height @ 525mm(h) , back height @ 400mm )

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
Rate
S.No. Specification unit Amount
In Rs
Qty.
2 Center table for VIP Waiting area
Dimension (W)1130mm X (D)630mm X (H)410mm 1 nos 30800.00 30800

Supplying and placing in position of centre table as per photograph. The centre table made of solid wood (steam
beech) in pu matt polish.The plain glass placed the top of the table in 8mm thk. The turned wooden legs are
sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a
focal point and some support. Add volumes of style to yourliving room with the centre table. Material &
subtype: Solid Wood -Beech Wood( spc:steam beach), Colour & Colour Family:Brown - Dark
Oak,Shape:Rectangular,Legs/Base:Solid Wood, Finish:Glossy,Style:Contemporary.The product should be from
the manufacture which have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC
Certification,AIOTA Certification, SEDEX Certification. The product should be as per above given specification
under the guidance of Engineer in charge.

3 Foldable Table for Breakout area (6 seater)

Dimesnion:1500mm (L) x750mm (D) x 750mm (H) 5 nos 44000.00 220000

Supplying and placing in position of foldable table as per photograph. The table top are made out of 25mm thk
prelam particle board with pvc edge banding. Understructure made out of metal crca with duly powder coated
finish..The product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
Rate
S.No. Specification unit Amount
In Rs
Qty.
4 Chairs for Breakout area 30 nos 7265.00 217950

supplying & providing cafeteria chair size is 393mm(l)x 431mm(d)x 876mm(h) a combination of bent
laminated veneered plywood with stainless steel make the products utile and a delight, seat & back structure
made by fully moulded bent wood chair with veneer in pu polish (plywood is grade - 303) to make the chair very
comfortable without padding and to give it a light appearance, designer used three-dimensionally shaped
plywood parts & in back supreme design 3 - holes which gives a outstanding look, chair seat & back based on
under structure to be a welded assembly the tubular welded under structure frame is made from shell with ss
202 grade 16 gauge heavy frame with t nut fitting & indoor grade uv resistance and pressed fitted with stainless
steel four legs ( 2 straight + 2 slant ) the tube are buff polished to give shiny finish. The chair is easy to store
when not in use, since you can stack up to 6 chairs on top of each other..The product should be from the
manufacture which have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC
Certification,AIOTA Certification, SEDEX Certification. The product should be as per above given specification
under the guidance of Engineer in charge.

7 Sofa for board room (3 seater)

Dimension (W)2020mm X (D)905mm X (H)850mm 6 nos 92400.00 554400

Supplying, and placing in position of sofa as per photograph.This sofa is constructed with a combination of
solid wood and ply along with zig zag springs to give a sturdy and durable stance. Top grain Italian Leatherette
upholstery. Solid German Beech Wood Frame,Sleek wooden legs.Seating Height :495mm, Legs: Solid
Wood..The seat cushion is made of multi layered foam of density 35-38kg/m3. The seating cushion have 2.75 &
1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest
has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The polyster polyfill keeps the upholstery
wrinke free & soft. The product should be from the manufacture which have BIFMA membership
Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification, SEDEX Certification. The
product should be as per above given specification under the guidance of Engineer in charge.

8 Café Table
Dimesnion:1500mm (L) x750mm(D)x 750mm(H) 13 nos 41720.00 542360

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
Rate
S.No. Specification unit Amount
In Rs
Qty.

Supplying, and placing in position of cafe table as per image/drawing. Table top made out of 25mm thk prelaminated
particle board with 2mm thk pvc edge banding with ms powder coated "C" shape legs of size 50 x 50mm Comprising
of metal powder coated cross connectors of size 40mm X 40mm. . The working edges shall be provided with machine
pressed 2mm thick PVC edging using special hot melt glue at hot temperature. The product should be from the
manufacture which have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA
Certification, SEDEX Certification. The product should be as per above given specification under the guidance of
Engineer in charge.

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST
 Total
Rate
S.No. Specification unit Amount
In Rs
Qty.
9 Cafe Chair 52 nos 4166.00 216632

Supplying & providing cafeteria chair size is 381mm(l)x 419mm(d)x 839mm(h) a combination of synthetic
fiber with stainless steel make the products utile and a delight, the complete structure shall be made up of 20%
glass filled blow molded high-density polyethylene andis,the frame structure shall be supported by ( 2 straight +
2 slant ) four legs.the tubular welded frame is made from dia2.22 +/- 0.03cmx 0.12+/- 0.0128 cm and 3.5+/-
0.03 cm x 0.12+/- 0.0128 am stainless steel 202 grade tube & the tube are buff polished to give shiny finish.seat
and in back given handle to hold are made of injection moulded high impact strength polypropylene polymer
compound with indoor grade uv resistance and pressed fitted with legs.the chair is easy to store when not in
use, since you can stack up to 6 chairs on top of each other.The product should be from the manufacture which
have BIFMA membership Certification,GREENGUARD,GREENPRO,FSC Certification,AIOTA Certification,
SEDEX Certification. The product should be as per above given specification under the guidance of Engineer in
charge.

Total Amount Including GST@18% In Rs= 1,937,542

Digitally signed by AMIT

SINGH
Date: 2024.08.27 16:02:05 IST