Institute of Testing and]... so ebcramaseee Certification (INDIA) ‘3, 2, Mofall 160035 Pb. Te Private Limited be asielnericrateay INDIA IN Intogteinaia.org =\ - Laboratory Test Report Cable glands for electrical installations ‘Test Report No. ITC/TEST/NN/2404/10-B2 Discipline. Electrical Group... Cables & Accessories Date of issue 28-06-2024 Sample date ...orerrnonn 11-04-2024 Date of Performance......... seers 12-04-2024 To 08-06-2024 Applicant ss...sssn “ Mr:Birju Jotwani Customer. sesame M/S Cabtech International Plot no, 3027, GIDC Phase Ill, jamnagar, Pin-361004, Gujrat (INDIA) Sample description Industrial Cable Glands Sample Condition... OK Customer Reference......... m N/A ‘Trade mark / Manufacturer. . - } / Cipcabiech Model / Type / Reference...u.nusw CTI CW40L/ CW Single Compression Armoured Cable Glands RatingS.ssssesoonenita N/A Test method(s).. BS 6121-1:2005 Overall verdict Inet of Teg Co pass Fail o Page 1 of 16 Signatory [REMARKS: This report ls governed by, akd ingbfporates by reference, the Condition of testing as posted at its date of issuance ‘and is Intended for your exclusive use. Any copying oF replication of this report to or for any other person or entity, or use of ‘cur name or trademark, ls permitted only with eur prior written permission. This report sets forth solely our findings with fespest tothe test somples Mentified herein. Ie includes all of the test requested by you and the results thereof based pon the Information thet you provided us with. You have 2 weeks from the date of issuance ofthis report to notify us of any material rat such notice shell be written and shall specfically address the issue you wish to foive. A failure to raige such issue within the prescribed time shall constitute your unqualified acceptance of the Completeness of this report, the tests conducted and the correctness of the report contents. Tests are destructive and non reveralble, the submitted sampler will not return to thelr original conditions. The Customer acknowledges that any remaining part ofthe sample will be discerded if not retrieved in aperied of 3 weeks from the date of issuance if this report. NABL APPROVED LABORATORY&.. INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Possible test case verdicts: Test case does not apply to the test object. Test object meets the requirement. Test object does not meet the requirement. ‘Test case does not evaluated to the test object. General remarks: "See enclosure##” refers to additional information related to this report in the annexes section. “See table ##” refers to a table appended to this report in the annexes section. “See figure ##" refers to an image, picture or drawing appended to this report in the annexes section “See ** highlights those clauses which are not in our NABL Scope. ‘Throughout this report, a comma is used as decimal separator. Overall Verdict is applicable to the clauses against which Testing has been performed, not to the clauses where it s N/A (Not Applicable). ‘The results of this report is against the sample received through the customer only. ‘The laboratory is not responsible for the authenticity of the data / documents submitted by the customer. ‘The laboratory will perform the testing at ambient temperature unless Environmental Conditions are not specified in the Testing Standard, Measurement uncertainty will be mentioned in the Table Le Test Details. If Test Verdict has been given in this Report. The Decision Rule as per LAC G8:2009 where guard Value (W=1u) will be made (TL=AL+W), whether Decision Rule will only be applied ifthe measured value is within the Guard Band. In such case Reference of this ‘clause will be given by marking. ‘The list of documents submitted by the customer is mentioned as under: List of Documents Remarks Marking Plate of DUT Provided by the manufacturer Ratings of DUT N/A Labels of DUT N/A Instruction Manual Provided by the manufacturer Circuit Diagram N/A General Assembly Diagram Provided by the manufacturer Bill of Material/ Critical Component List N/A Please specify, ifany other z Ingffute of Yesting and Certification ) Prt. ‘Test Report No. ITC/TEST/NN/2404/10-2 Page 2 of 16 Authorised Signatoryé won 'NSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. General Product Information: Industrial Cable Glands CTI CW40L/ CW Single Compression Armoured Cable Glands Pictures of Specimen received: Marking Mr. Sahil 5 M in Chopra Reviewed By Division head ‘Bathorized By Asst. (Electrical) — General Manager Technical wofrnte of festing and Cerrification ‘Test Report No. ITC/TEST/NN, ale Page 3 of 16 Authorised Signatoryfn INOUA (INDIA) PVT. LTD. INSTITUTE OF TESTING AND CERTIFICATION weit Ghause no. Requirement - Test Wesults-Memarks | Verdict Requirements: Ad Construction 411 General ‘Armour glands shall not have any internal sharp edges, which might cause damage to any cables, flexible cables or insulated conductors which pass through them in service smooth | | Wire ways round and ‘Those parts of an armour gland that are used for tightening or for holding during installation shall be of hexagonal form Outside of gland is of Hexagonal shaped External projecting edges and corners of armour gland components shall be smooth and free from burrs burrs External edges _are smooth and free from iY 412 Entry thread The entry thread of metric armour glands in sizes up to M75 shall be constructed in accordance with BS EN 60423:1995, Table 1. M40 size gland For sizes greater than M75 the entry thread shall be constructed in accordance with BS ISO 965-3 and with a thread pitch of 1.5 mm, 2 mm or3 mm. N/A 42 Performance 424 ‘Mechanical performance 4241 Cable retention ‘Alter testing in accordance with BS EN 50262:1999, 10.4.1, but using the force specified in Table 1, the cable shall not have moved relative to either of the glands by more than 3 mm attheend of a5 min test. Incompliance Force: 350N Displacement <3mm A212 Resistance to impact Using the impact values applicable to the impact category that the gland Is claimed to be, as stated by the manufacturer, the armour gland shall show no visible signs of damage after tested as per BS EN 50262:1999 of 9.4 Refer table A 4213 Resistance to excess torque For armour glands that are assembled by being screwed together, after being assembled on a piece of cable having the largest armour thickness in the range for which the gland is suitable, as stated in the information supplied by the manufacturer, using a torque 1.5 times the installation torque_given in the manufacturer's instru armour gland shall show no visi Ce ) Pvt. Ltd Tightning No visible after the test 0.90*1,5=1.35Nm torque: damage jor —E | ‘Test Report NolTC/TEST/NN/244/1! Praca ‘Signatory Page 4 of 16i INSTITUTE OF TESTING AND CERTIFICATION INDIA, (INDIA) PVT. LTD. wan Requirement Test 422 Electrical performance I 4221 Equipotential bonding | When armour glands which are claimed by the | manufacturer to provide equipotential bonding | are tested in accordance with BS EN | Refer table B 50262:1999, 10.1, in no case shall the resistance exceed 0.1 0. 42.2.2 Electrical connection to metallic layer(s) of cable When armour glands are tested in accordance with BS EN 50262:1999, 10.2, the resistance between the gland and the armour shall not exceed 0.10. Refer table C When armour glands which are claimed by the manufacturer to provide an electrical connection to metallic layer(s) of the cable other than the armour are tested in accordance with BS EN 50262:1999, 10.2, the resistance between the gland and each metallic layer of the cable other than the armour shall not exceed 0.1 0. N/A 42.23 Insulation resistance | When armour glands which are claimed by the | manufacturer to have insulating characteristics are conditioned in accordance with BS EN 50262:1999, 10.3.1, and then tested in Metallic Glands accordance with BS EN 50262:1999, 10.3.2, the insulation resistance shall be not less than 5MQ. | N/A 4224 Protective connection to earth When armour glands which are claimed to have a protective connection to earth are tested in accordance with BS EN 50262:1999, 10.4.2, using the current specified for the | Refer table D relevant category of gland as given in BS EN 50262:1999, Table 5, for 1 s, the following requirements shall be met During the test, the flow of current shall not be | Continous current flow interrupted. for isec ‘After the test there shall be a contact resistance between the armour close to the gland and the earthing connections, measured with a source of at least 10 A, of 0.1 11 or less. Refer table D Alter the test the gland shall not exhibit any cracks visible to normal or corrected vision without magnification and shail not have any loase parts or show! sf Put. Ltd) No visible cracks or deformation found on gland after the test Page 5 of 16 ‘Test Report Nol TC/TEST/NN/2404, CP aterved i a6... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. went Hequirement Test Results - Remarks 423 Resistance to environmental factors 4231 Ingress protection Armour glands shall provide a minimum degree of protection of IP2X when tested in accordance with BS EN 60529:1992 1P66 protected Refer table E.1 & E.2 423.2 Resistance to abnormal heat When exposed non-metallic parts of the armour gland are tested in accordance with BS EN 50262:1999, 12.2: Metallic Cable gland N/A — there shall be no flame or glowing which does not extinguish within 30 s after removing the glowwire; — there shall be no ignition of the tissue paper or scorchingof the board. N/A N/A 4233 Resistance to salt and sulfur dioxide laden atmospheres When armour glands, other than armour gands made wholly of stainless steel or brass, which are claimed to be resistant to salt and sulfur dioxide laden atmospheres, are tested in accordance with BS EN 50262:1999, 12.3, the Jands shall show no visible signs of corrosion. No signs of corrosion found after the test ‘Test samples, test conditions and test schedule ‘Marking and information Each armour gland shall be marked in accordance with BS EN §0262:1999, 7.1 Provided on gland ‘After testing in accordance with BS EN 50262:1999, 7.2, the marking on the armour gands shall be legible when viewed with normal or corrected vision without magnification. Engraved marking ‘After the glands have been subjected to testing in accordance with the schedule specified in 5.4 the marking shall remain legible. Engraved marking 62 Information ‘The manufacturer shall provide with each package of armour glands an information sheet giving atleast the following information a) the cable acceptance range (Le. the maximum cable diameter and the minimum and maximum armour thickness with which the land can be used); Cable range 33mm to 40.5mm Armour Wire Dia: 1.6mm to 2.0mm b) the installation torque for glands that are assembled by being scre ther: 09Nm L 9 ‘entry thread length; 15mm Instiute gf Testing of Certification (india) FA [Test Report NoITC/TEST/NN/2404/1 ‘utherised Signatory Page 6 of 16fe. INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Beer ‘Clause no. ‘Requirement - Test ‘Results - Remarks Verdict d) _| impact category; Category 8 P 6 instructions for safe assembly of the armour | Provided in instruction |» ‘gland: manual ) __| entry thread specification (ifnot metric); M40 metric P @) _| the gland provides equipotential bonding: P a ifthe gland provides an electrical connection to h) | metallic layer(s) of the cable other than the P armour; 1) __| ifthe gland has insulating characteristics; N/A ifthe gland provides a protective connection to ))__| earth, and ifso the category; Sameera WA ig) _| the dearee of ingress protection provided: TP 66 Declared by the | manufacturer if the gland is resistant to salt and sulfur D__| dioxide laden atmospheres, Incompllance: P Insttut and Certification (indiayfPvt. Ltd. ‘Test Report NolTC/TEST/NN/2404/11 Page7of16 |& INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. INDIA waa Gause no. Requirement ~Test Rewulls~ Remarks [Verdict | Tablea C14.2.1.2 Resistance to impact | Preconditioning before impact test ‘Temperature I =25°C Time Duration SHours Impact impact ‘Sogory Enemy | Mass (Ke) Height (m) Verdict os 20.0 20 1.0 P Test Setup Invstiteste Certification (india [‘Test Report NolTC/TEST/NN/2404/10, Page 8 of 16 Authorised Signatoryé... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Bs612i Clause no. Requirement - Test Results Remarks | Verdict TableB CL 4.2.2.1 | Equipotential bonding to electrical equipment Max ‘Measured Hest usrent Durston limit(Resistance) | resistance 10Amps Amin 010 32.8m0 Test Setup TableC “CL4.2.2.2 | Equipotential bonding to metallic layer of cable Max Measured Tasers — limit(Resistance) resistance ‘10Amps | min 0.10 5.7m. insite of Testing and Certification ia) Pvt. Ltd) “Test Report NolTC/TEST/NN/2408/104 7 Page9ofté | Authorised Signatory&... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. wer Gauze, Requirement = Test Results Remarks | Verdict Table D CL4.2.2.4 | Electric current test _ Category A Cable Diameter | —_—‘Testcurrent =| Duration >31to 43mm 500Amps | Isec ‘Test Setup Resistance measurementafter the electric current test Max Measured Test Current Duration | simitfResistance) | resistance 10Amps amin 1 6.2mn Test Setup insttusg’6f Testitg and Certiicetion (incif Pvt.Ltd. ‘Test Report NoITC/TEST/NN/2404/ Page 100f16 | ‘Authorised SEnaTOTyfi INSTITUTE OF TESTING AND CERTIFICATION INDIA (INDIA) PVT. LTD. Wwe Clause no. Requirement —Test TableE1 14.3.2 Degree of protection in accordance with IEC 60529(IP Codi Test Condition for characterstics numeral 1P6X Remarks The enclosure shall be deemed category 1, whether reductions in pressure below the atmospheric pressure are present or not. Maximum depression 2kpa (20mbar) Test Duration Bhours ‘Acceptance conditions for first characteristicnumeral 6 The protection is satisfactory if no deposit of dust is observable inside the enclosure at the No dust find inside the enclosure fitted with cable gland after the test endof the test. Testing phot tographs During the test photograph ‘After the test photograph ‘and Certification Page 11 of 16 fa); ‘Test Report NolTC/TEST/NN/2404f 1} ‘Authorised Signatory6... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Bseizi ‘Glawse no. Requirement Test Results~Remarks | Verdict Table E.2 432 Degree of protection in accordance with IEC 60529(IP Code) Z Test for second characteristic numeral 6 eters with the 125 mm nozzle = The test is made by spraying the enclosure from all practicable directions with a stream of water from a standard test nozzle. Internal diameter of the nozzle 12.5 mm Delivery rate 100 I/min 5 96. Minimum test duration 3 min Distance from nozzle to enclosure surface: 25mand3m between ‘Acceptance conditions for second characteristicnumeral 6 ‘After testing enclosure shall be inspected for ingress of water. ‘No water found inside the enclosure fitted with cable gland after the test “Testing photographs ‘Afier the test photograph Inffitute of Yesting and Certification (hais) Pv td. “Text Report NoITC/TEST/NN/2404] 10-897 — Page 12 of 16 —Ramnorised Signatory&... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. wet Giause no. Requirement Test Rewults—Remarks | Verdict CABTECH INTERNATIONAL ee el 1 “ I as6121 PART 12008 ees ce SECTON AA na im of ‘and Certification (fais) Pv, ‘Test Report NoITC/TEST, MNO OEE Page 13 of 16 ‘Authorised Signatoryé... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Bez Giause wo. Requirement Test Results—Remarks | Verdict GA of tested samples CABTECH INTERNATIONAL © GNETECn werEvountionAL Insipite of and Certification PR “Test Report NolTC/TEST/NN/2404/20-BR 7 Page 1 of 16] Autherised Signatoryé... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Bera Clause no. Requirement - Test Results- Remarks | Verdict | erratic [ma] _oeawna nS institute/Of Tedting and Certification idiayPPvt. Ltd [Test Report NoITC/TEST/NN/2404, _— Sianator Page 15 of 16]é INSTITUTE OF TESTING AND CERTIFICATION INDIA (INDIA) PVT. LTD. weit Gauseno, Requirement -Test Results ~ Remarks Verdict SECTIONAA *****END OF THE REPORT***** ‘and Certification Awthsrined Signatory “Test Report NoITC/TEST/NN/2404/10. Page 16 of 16Institute of Testing and Mob +01-se72445146 BEB Certification (INDIA) | "=item teers ‘Web: wwwiteindla.org te pia Private Limited mall: [email protected] "Laboratory Test Report Cable glands for electrical installations Test ReportNo. ITC/TEST/NN/2404/10-B1 Discipline. Electrical Groupirsniinisinisnianninininsnnsn Cables & Accessories Date of issue... Jdistiiinn 28-06-2024 Sample date in, 11-04-2024 Date of Performance, 12-04-2024 To 08-06-2024 Applicant sinissessnis Mr Birju fotwani Customer... M/S Cabtech International Plot no, 3027, GIDC Phase Ill, jamnagar, Pin-361004, Gujrat (INDIA) Sample description sia Industrial Cable Glands Sample Condition... . OK Customer Reference ..ss.iesuns N/A Trademark / Manufacturetissnison Pp Cablech Model / Type / Reference, CTL CW40L/ CW Single Compression Armoured Cable Glands Ratings. N/A Test method(s) ss oy IEC 62444:2010 EN 62444:2013 Overall verdict tind Pass & Fal =O Page Lof 18 RUMARKS: This report Us governed by, and inctraGates by reference, the Condition of testing as posted ot Its date of issuance ‘and Js tutended for your exclusive use. Any copyigg oF replication of tis report to or for ony other person or entity, or use of ‘our name or trademark, (s permitted only wiour prise written permission. This report sets forth solely our findings with ‘respect to the test samples identified herein, It includes all ofthe ext requested by you and the results theeeo} based upon the Information that you provited as with. You have 2 weeks from the date of tssuance of ths report to notify us of any material ‘error or omission; provided, however, that such notice shall be written and shall specifically address the istue sow wish to raze. A failure to raise such Issue within the preseribed time shall constitute your unquclifiel acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Tests are destructive und non ‘reversible, the submitied samples will not return to thelr original conditions. The Customer acknowledges that any remaining art ofthe sample willbe discarded i not retrieved 10a period of 3 weeks from the date of tsuanex If this report. NABL APPROVED LABORATORYé... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Possible test case verdicts: * Test case does not apply to the test object. N/A ‘© Tost object meets the requirement........ wou (Pass) * Testobject does not meet the requirement. F (Fail) ‘ Testcase does not evaluated to the test object. General remarks: © “See enclosure##" refers to additional information related to this report in the annexes: section. “See table ##” refers to. table appended to this report in the annexes section. "See figure ##” refers to an image, picture or drawing appended to this report in the annexes section “See *” highlights those clauses which are not in our NABL Scope. ‘Throughout this report, a comma is used as decimal separator. Overall Verdict is applicable to the clauses against which Testing has been performed, not to the clauses where it is N/A (Not Applicable). ‘The results of this report is against the sample received through the customer only. ‘The laboratory is not responsible for the authenticity of the data / documents submitted by the customer. «The laboratory will perform the testing at ambient temperature unless Environmental Conditions are not specified in the Testing Standard, ‘+ Measurement uncertainty will be mentioned in the Table ie Test Details, * If Test Verdict has been given in this Report The Decision Rule as per ILAC G8:2009 where guard Value (W=1u) will be made (TL=AL.+W), whether Decision Rule will only be applied if the measured value is within the Guard Band, In such case Reference of this clause will be given by marking, «The list of documents submitted by the customer is mentioned as under: List of Documents Remarks Marking Plate of DUT Provided by the manufacturer Ratings of DUT N/A Labels of DUT N/A Instruction Manual Provided by the manufacturer ‘Circuit Diagram - N/A General Assembly Diagram Provided by the manufacturer Bill of Material/ Critical ComponentList N/A Please specify, ifany other Testing and Centiicaton ( td. ‘Test Report No. IPC/TEST/NN/ 2404/1 Page 20f18 | Authorised Signatoryé won 'NSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. General Product Information: Industrial Cable Glands CTI CW40L/ CW Single Compression Armoured Cable Glands Pictures of Specimen received: nob Cue Mr Sahil Sag a = Sr. Testing Engineer | Reviewed By Division head thorized By Asst. Electrical General Manager Technical 7 (Test Report No. IPC/TEST, BRED SS Page 3 of10_|& INSTITUTE OF TESTING AND CERTIFICATION NIA (INDIA) PVT. LTD. aN CAA Clause no, Requirement - Test ‘Results - Remarks ‘Verdict According to Material Metalliccablegiands, [in Compliance Non-metallic cable glands, Composite cable glands, ‘According to Mechanical Properties Non-armoured cable retention oranchorage _| Armoured cable giands | Anchorage type A N/A Anchorage type B N/A Retention only N/A Armoured cable anchorage N/A | ‘Anchorage Type C In Compliance Pp ‘Anchorage Type D N/A ‘Impact category | Category 1 N/A Category 2 N/A. Category 3 N/A | Category + N/A Category 5 N/A | Category 6 N/A | Category 7 _ N/A Provided by the | Curegery Ss manufacturer F | ‘According to Electrical Properties | With electrical continuity characteristics, N/A | Equipotential bonding to enclosure In Compliance P Electrical connection to metallic layer(s) of cable| In Compliance P Cable glands with connection to protective earth = Category A P| Category B N/A Category N/A | According to resistance to — external ] influences 64a [Degree of protection in accordance with 1EC|1P66 Declared by the P “44 |60529 (IP Code) with a minimum of IPS4 manufacturer 60°C To +120°C ‘Temperature range if different from that defined, 642 Jin sub clause 85 (Detlarest by ;P Manufacturer) | Inst [Test Report No.JTC/TEST/NN 2 )4/10% Page 40f 18fi INSTITUTE OF TESTING AND CERTIFICATION INDIA (INDIA) PVT. LTD. Tatyana Glause no. Requirement — Test Results Remarks | Verdict [Resistance to ultraviolet light for non-metallic ‘ 643 cable glands ‘Metallic cable gland 64.3.1 Resistance to ultraviolet light not declared N/A 64.3.2 [Resistant to ultraviolet light N/A 6.5 |According to sealing system 65.1 With asingle-orifice seal ‘Single-orifice seal P 65.2 |With a multi-orifice seal N/A 7___|Markingand Documentation 7A |Marking | Cable gland shall be legibly and durably marked] ina visible place with the following: Lo name, logo or registered mark of the Provided CTimarkon |, é manufacturer or supplier; [sample 1 z = [ideotieation othe product CTIcWAOL provdedon| ~ p 7.2 Durability and legibility The test is made by rubbing the marking by hand for 15 s witha piece of cotton cloth soaked | Engraved Marking with water and again for 15 s with a plece of|Used aie cotton cloth soaked inpetroteum spirit After this test, the marking shall be legible to’ ‘normal or corrected vision without additional Eagreved Marking N/A | magnification. The marking shall remain legible after all the non-destructive tests of this standard. It shall |Engraved Marking Nya | “not be possible to remove labels easily and they Used iV) _shall not show curling Documentation ‘The manufacturer or supplier shall provide in his literature all information necessary for the : proper use and safe installation, such as: sealing range (maximum and minimum cable irsenatonsh 33mm to 405mm. P installation torques, _[0.90Nm P ‘entry thread length, [15mm P entry thread Size, and type; [M40 metric P maximum clearance hole diameter; [40.22mm P itype of cabie anchorage and anchorage range, |TYPEC [_P. Limpact category; Category 08 ee ‘correct assembly of the cable gland for use as ‘part of the PE conductor or electrical | N/A _connection; _ | “degree of protection mee with IEC|IP65 Declared bythe |p (60529 (IP Code) ifhis manufacturer ‘Test Report No{TC/TEST/NN/2404Y 1 Page Sof 18 _|Gi INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. NDIA TaCjEN Goa, Requirement —Test Resulis-Remarks | Verdict temperature range 60°C To +120°C| Decared by the| P manufacturer multi orifice seals Single orifice seal N/A | \Construction a1 Those parts of a cable gland that are used for tightening or for holding during installations shall be suitable for gripping without damage to, lavailable tools or following the manufacturer’ instructions, the cable gland or cable with commonly | | In compliance P a2 cable gland components shall be smooth, to prevent danger from injury in handling the cable gland, [All external projecting edges. and corners of Smooth Edges & Corner | P. 83 Cable glands shall be constructed to avoid cable damage when installed in accordance with the manufacturers or suppliers instructions, No harm or damage to \cable found during P installation cee Cable glands shall provide a minimum degree of IPS4 inaccordance with LEC 60529. 1P66 declared by the P manufacturer 85 Cable glands shall be suitable for use within a temperature range from at least -20 °C to at least 65°C. In Compliance PB 86 7 Metallic parts shall be resistant to or protected. lagainstcorrosion. Refer material certificate no : N/A BMA-23-1008 87 ‘Cable gland declared in accordance with 6.4.3.2 ‘shall have adequate resistance to ultra-violet light, Metallic cable gland N/A Mechanical properties General Cable glands declared in accordance with 6.2.1.1 cable anchorage in accordance able retention” N/A [Cable retention test and with a sealing system in accordance with 6.5.1. For Cable glands classified according to 6.2.1.3| N/A For Cable glands classified according to 6.2.1.3 land with a sealing system in accordance with 16.5.2. N/A [The load is maintained for § min and at the end ‘of this period the displacement shall not exceed ‘3. mm when unloaded, N/A Nn Gn a/ Put. Lid. nutyof and Certification ‘Test Report No.lTC/TEST/NN/ 2404/10, gnatory Page 6 of 184... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. ‘Tecjen 6aaas Requirement Test Resulis-Remarks | Verdict Cable anchorage test for non-armoured cable | Armoured cable glands, Cable glands declared with cable anchorage in’ accordance with 6.2.1.1 and 62.1.2 shall relieve the conductors from strain, inciuciing twisting N/A ‘The test mandrel is pulled 50 times for duration | of 1 s, without jerks in the direction of its axis with the relevant pull force. N/A ‘At the end of this period the displacement shall not exceed 2 mm. N/A The sample with the test mandrel is mounted onto the test arrangement for the cable anchorage twist test. N/A During this test the test mandrel shall not turn by more than an angle of 45°. N/A oA (Cable anchorage test for armoured cable ‘The cable is marked so that any displacement relative to each cable gland can be easily|In compliance detected. The load is maintained for 5 min and. at the end of this period the displacement shall not exceed 3 mm at either cable gland. Force: 350N P Displacement <3mm 95 Resistance to impact Cable glands shall be resistant to impact as’ classified according to 6,2.3, Refer Table: A P ‘The mass shall be fitted with an impact head of hardened steel in the form of a hemisphere of 25 mm diameter, In Compliance P [After the test the sample shall show no sign of disintegration nor shall there be any cracks| visible to normal or corrected vision. ‘After the testnocrack | found 96 Seal performance For cable glands with a sealing system in accordance with 6.5.1. In compliance P For cable glands with a sealing system in accordance with 6.5.2. Single-orifice Seal N/A 10 Electrical properties 10.1 Equipotential bonding to electrical equipment Cable glands declared in accordance with 6.3.1.1 shall have adequate conductivity to the electrical equipment. - ‘The resistance shall notexceed 0.1 In Compliance Pp jo 10.2 Equipotential bonding to metallic layer(s) of cable Refer Table: B Cable glands dectared in ao In Compliance P bis Page 7 of 18é INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. INDIA TeCyEN ean Requirement —Test Results Remarks | Verdict | the metallic layer(s) of the cable. [The resistance shall not exceed 0.1.0 Refer Table: C Protective connection to earth |General ‘Cable glands declared in accordance with 63.1.3| Ishall be capable of passing an earth fault current In Compliance Electrical current test [This test is carried out after test in 9.4 and 10.2 'The assembled samples shall be connected with {the high current source as shown in Figure 6 and [subjected to the electrical current values given in Table 5 according to the category declared by) the manufacturer or supplier for a period of 1s. Refer table D [The samples shall be deemed to have passed the | tests if, ithey withstand the current for the specified period; |Sample withstandard é the test [the contact resistance between the armour close lto the samples and the earthing connections, measured with a source of at least 10 A, is equal to or less than 0,1 2; Refer table D they do not show any cracks to normal or| corrected vision without magnification nor have| lany loose parts or deformations impairing normal use; No cracks found after the test i Electromagnetic compatibility N/A 12 External influences 124 ‘Degree of protection in accordance with IEC 60529(1P Code) 1244 G ‘The degree of protection, as declared by the manufacturer and provided by the cable gland is checked in accordance with 12.1.2 immediatoly followed by 12.1.3 IP 66 declared by the manufacturer 12.1.2 Degree of protection against foreign solid lobjects (The sample is mounted onto an appropriate test enclosure where the mating surface which come | into contact with any part of the sample shall be| flatand smooth, In Compliance ‘The sample shall be tested in_accordance with the appropriate test of 1EC-60529 subclause 5.2 "Protection against inj 3s of solid foreign Refer table E.1 IP6X performed objects” Page 8 of 18 Authorised Signatoryé INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. NDIA TECEN 62aaS, ‘Clause no. ‘Requirement - Test For characteristic numeral 5, category 2 applies. ‘The sample is deemed to have passed the test if there isno ingress of dust. No dust find inside the enclosure fitted with cable gland after the test ‘Degree of protection againstingress of water ‘The sample shall be tested in accordance with |the appropriate test of IEC 60529 clause 6. Refer table E.2 For characteristic numeral 4, the test device as |show in figure 4 (oscillating tube) of IEC 60529 shall be used. IP X6 performed ‘The sample is deemed to have passed the test if [there isno ingress of water No water found inside ithe enclosure fitted with cable gland after the test 12.2 Resistance to corrosion (Cable gland shall have resistance to corrosion. Refer material \certificate no : BMA-23-1008 N/A Cable glands made from non-metallic materials, | stainless steel containing at least 13 % chromium, copper alloys containing at least |55 % copper, Aluminium alloy and zine alloy are not subjected to the test. ‘Copper $7.400% on ‘certificate provided the manufacturer by | N/A ‘The sample shall have passed the test if there is! no sign of red rust visible to normal or corrected: vision. N/A 13 Fire hazard 13.1 Reaction to fire [13.4.4 General Exposed non-metallic parts of cable glands shall be resistant to abnormal heat from an external source. Metallic cable gland N/A ‘Sealing systems are exempt from this test. N/A For the purpose of this test external exposed parts are those parts which can be touched by a glow wire. At 650° Metallic cable gland N/A ‘The cable gland is regarded as having passed the ‘glow wire test if N/A there is no flame or glowing Metallic cable gland N/A “flames or glowing at the cable gland, extinguish \within 30 s after removing the glow wire and |there shall be no ignition of the tissue paper or | scorching of the board. l Metallic cable gland N/A Page 9 of 186 INSTITUTE OF TESTING AND CERTIFICATION IOLA, (INDIA) PVT. LTD. Teen aaa Gaasena, Requirement Test esulls= Remaries | Verdict | Tablea aos Resistance to impact ] Preconditioning before impact test ‘Temperature ~25°C ‘Time Duration Hours impact T Category nergy) M25 (Ke) Helght (m) Verdict ® 20.0 20 io [_¥ Test Setup wofeapamtc [Test Report NoITG/TEST/NN, are Page T0etie | ‘Authorised Signatoryé... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. TeC/EN 62a Clause no. Requirement - Test Results-Remarks | Verdict TableB L10.1 | Equipotential bonding to electrical equipment : Measured ‘Test Current Duration iimit(Resistance) reikeanwe 10Amps min 0.10 328m2 CL.10.2 —_| Equipotential bonding to metalliclayer of cable Measured TestCurrent | —_Duration Maxlimit(Resistance) | esistance 10Amps Imin o1n 57m Test'Setup liyfftuto Of Testing and Certification ia) Py) Mid Test Report NoITC/TEST/NN/2404) 10, Page 11 0f 18 | Authorised Signatory& INSTITUTE OF TESTING AND CERTIFICATION NDIA (INDIA) PVT. LTD. Terenas Giaaseno. Requirement Test Results Remarks | Verdict TableD ¢L10.3.2 | Electric current test ___ Category A - - Cable Diameter Test current Duration >31 to 43mm. 500Amps - sec Test Setup Resistance measurementafter the electric currenttest Max ~ Measured Tek Carrent Puration _|__imit(Resistance) | resistance 10Amps Amin | on 62m Inetituy (nai ‘f Testing and Certification Pvt. Ltd, [Test Report No.ITC/TEST/NN/ 2406/1 a Pago 12 of 18 |fre INDIA, INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. aC cana Clause no, Requirement -Test TResulis~ Remarks | Verdict Table E.1 aziz Degree of protection in accordance with IEC 60529(1P Code) ‘Test Condition for characterstics numeral 1P6x Remarks The enclosure shall be deemed category 1, whether reductions in pressure below. the atmospheric pressure are presentor not. Maximum depression Tkpa (Zombar] ‘Test Duration Bhours ‘Acceptance conditions \characteristienumeral 6 _ for first dust Is observable inside the enclosure at the | end of the test. No dust find inside the enclosure fitted with cable gland after the test tographs Teg pa During the test photograph ‘After the test photograph and Certification ‘Test Report No{TC/TEST/NN/240. Page 13 of 186... INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. a ‘Clause no. ‘Requirement ~ Test ‘Results - Remarks Verdict Table E.2 [craa.4.3 ‘Degree of protection in accordance with IEC 60529(IP Code) ——— Romar [The test is made by spraying the enclosure from all practicable directions with 2 stream of water - froma standard test nozzle. 7 {Internal diameter of the nozzle 12.5 mm Delivery rate 100 I/min +5 %. Minimum test duration = = 3 min Distance from nozzle to enclosure surface: between “| 25 mand 3m ‘Acceptance conditions for second characteristicnumeral_ 6 ‘After testing enclosure shall be inspected for | No water found inside the enclosure fitted ingress of water, with cable gland after the test Testing photographs ‘After the test photograph neta (ioet [fest Report NolTC/TEST/NN/2404, Page 14 of 18 |é.. INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. TaC7EN Gta Clause no. ‘Requirement ~ Test Results“ Remarks | Verdict GA of tested samples io] _pewmone [roa] 21 [ew nace p02 fuaruna| ar [ownan-ncoral wom Joon Page 15 of 18 Authorised Signatoryé.. INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. neyN aT 1 Gause vo. | Requirement = Test [Results Remaries | Werdict | GA of tested samples CABTECH INTERNATIONAL © CABTECH UrTERNATIONAL -ASTEDN INTERNATIONAL Ries an aoa fara] Inavtute and Certification : _ __ (india) vt. Ltd, [Test Report No1TC/TEST/NN/2404/1( Page i60f 18 | ‘Authoriaed Signaioryé.. INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. TEC/EN 62taa Clause no. Requirement ~Test esas Remaris | Verdict GA of tested samples SECTIONA.A ‘SCALES 4 g and Carification Authorised Signatory Page 17 of 18é wx INSTITUTE OF TESTING AND CERTIFICATION (INDIA) PVT. LTD. Tae yaN e204 Glausena. Requirement Test [__ Resulis Remarks [Verdier «****END OF THE REPORT***** Page 18 of 18