CDC-X207 YU

CDC-X307 YU
CDC-X407 YU
CDC-X2070 YL
CDC-X3070 YL
CDC-X4010 YL

SERVICE MANUAL
STEREO CAR CD RECEIVER BASIC CD MECHANISM: TN-CCD1001-113J

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
of CDC-X207/ X307/ X407<YU>, (S/M Code No. 09-99B-422-3T1) and
CDC-X2070/ X3070/ X4010<YL>, (S/M Code No. 09-99C-422-3T2).
N
SIO
VI
RE

TA
DA

S/M Code No. 09-002-422-3R1

 SPECIFICATIONS

RADIO SECTION AUDIO SECTION

(FM) Max. Power Output 45 W x 4 channels
Frequency Range 87.5 MHz –108 MHz (100-kHz steps) <except CDC-X2070>
87.5 MHz –108 MHz (50-kHz steps) 35 W x 4 channels <CDC-X2070 only>
Usable Sensitivity 12.7 dBf
50 dB Quieting Sensitivity 17.2 dBf TAPE/MD IN input
IF Rejection 80 dB Input Sensitivity (load impedance)
Frequency Response 30 Hz – 15,000 Hz TAPE/MD IN 500 mV (10 kΩ)<YU>
S/N Ratio 63 dB 300 mV (10 kΩ)<YL>
Stereo Separation 35 dB at 1 kHz
Alternate Channel Selectivity GENERAL
70 dB Power Supply Voltage 14.4 V (11 to 16 V allowable),
Capture Ratio 3 dB DC, negative ground
Load Impedance 4Ω
(AM) Tone Control Bass ±10 dB at 100 Hz
Frequency Range 530 kHz – 1,710 kHz (10-kHz steps) Treble ±10 dB at 10 kHz
531 kHz – 1,602 kHz (9-kHz steps) Preamp Output Voltage (load impedance)
Usable Sensitivity 30 µV (30 dB) 2.2 V (10 kΩ)
Installation Size 182 (W) x 53 (H) x 155 (D) mm
Set the frequency increment for your area using the switch on the (71/4 (W) x 21/8 (H) x 61/8 (D) inches)
bottom of the unit.
(The switch is set at the factory to the 10k position [for the U.S.A.]) STEERING-WHEEL-MOUNTED REMOTE CONTROL UNIT <CDC-
X407/4010 only>
CD SECTION Dimensions approx. 67 (W) x 26 (H) x 27 (D) mm
Frequency Response 17 Hz – 20 kHz +0/–3 dB (23/4 (W) x 11/16 (H) x 11/8 (D) inches)
Dynamic Range More than 80 dB (excluding holder)
Channel Separation More than 65 dB Weight approx. 38g (1.33 oz.)
S/N Ratio More than 85 dB (including holder, battery)
Wow/Flutter Unmeasurable
• Design and specifications are subject to change without
notice.

ACCESSORIES / PACKAGE LIST

REF. NO. PART NO. KANRI DESCRIPTION

1 8A-KC7-902-010 IB,INST,YU,YL (3L,P)

1 8A-KCG-902-010 IB,YU(3L) 207<X207>
1 8A-KCG-901-010 IB,YU(3L) 307,407<X307,X407>
1 8A-KCG-903-010 IB,YL(3L) 4010, 3070, 2070<YL>
2 87-B10-141-010 NUT,5 TYPE-2

3 87-B10-143-010 UT1+5-15 W/O SLOT

4 87-B10-144-010 W,5.2-10-0.5
5 87-B10-145-010 W-SPR,5.3-8.5-1.5
6 87-B10-216-010 U+2.6-4.0 ZINC BLK (BH M2.6)
7 8Z-KC1-030-010 CASE,DFP -C

8 8Z-KC1-231-110 HLDR,HALF -C
9 8Z-KC1-232-010 KEY,REMOVE -C
10 8Z-KC1-235-010 HLDR,REAR MTG
11 8Z-KC1-244-010 S-SCREW,5*6 TH+ TAPPING ST
12 8Z-KC1-250-010 S-SCREW,HEXAGON

13 8Z-KT1-616-010 CONN ASSY,16P B52

-2-
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully CAUTION

the instructions below when servicing. Use of controls or adjustments or performance of proce-
dures other than those specified herin may result in
WARNING!! hazardous radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS ATTENTION
NECESSARY TO CONFIRM LASER BEAM EMISSION. L’utillisation de commandes, réglages ou procédures
BE SURE TO OBSERVE FROM A DISTANCE OF MORE autres que ceux spécifiés peut entraîner une dangereuse
THAN 30cm FROM THE SURFACE OF THE OBJEC- exposition aux radiations.
TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
ADVARSEL
s Caution: Invisible laser radiation when Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
open and interlocks defeated avoid ude af funktion. Undgå udsættelse for stråling.
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning, This Compact Disc player is classified as a CLASS 1
når sikkerhedsafbrydere er ude af funktion.
LASER product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle. CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
VARNING! LUOKAN 1 LASER LAITE
Om apparaten används på annat sätt än vad som KLASS 1 LASER APPARAT
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

Precaution to replace Optical block

PICK-UP ASSY
(OPTIMA-720AIE) P.C.B

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure
ground body and workbench, and use care
the clothes do not touch the diode.

1) After the connection, remove solder

shown in right figure.

-3-
ELETRICAL MAIN PARTS LIST

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
IC C205 87-A11-606-080 C-CAP,S 0.22-25 K B
C206 87-010-492-040 CAP,E 0.33-50 GAS
87-A20-446-010 C-IC,LA9241ML C207 87-010-195-080 C-CAP,S 0.068-25 Z F C2012
87-A21-319-010 C-IC,LC78622NE C208 87-010-176-080 C-CAP,S 680P-50 J SL
87-A21-488-040 C-IC,LA6556 C209 87-010-992-080 CAP, CHIP 0.047
8Z-KT1-622-010 C-IC,LC75374E
87-A21-562-010 IC,LA4743B C210 87-016-669-080 C-CAP,S 0.1-25 K B
C211 87-010-498-040 CAP,E 10-16 M 5L SRE
88-KT1-606-080 IC,PST994D C212 87-010-180-080 C-CER 1500P
87-A21-535-030 C-IC,LC72358N-9910 C213 87-010-992-080 CAP, CHIP 0.047
87-A21-489-030 C-IC,LC75853NW C214 87-016-669-080 C-CAP,S 0.1-25 K B
87-A90-951-010 RCR UNIT,SBX1971-52<X407>
C215 87-010-178-080 C-CAP,S 1000P-50 K B C2012<YU>
C215 87-010-182-080 C-CAP,S 2200P-50 K B C2012<YL>
TRANSISTOR C216 87-A11-606-080 C-CAP,S 0.22-25 K B
C217 87-016-669-080 C-CAP,S 0.1-25 K B
89-324-122-080 TR,2SC2412K C218 87-010-198-080 CAP, CHIP 0.022
87-A30-289-040 C-TR,2SA1037AK(R)
87-A30-288-040 C-TR,DTC114YKA C219 87-012-157-080 C-CAP,S 330P-50 CH
87-A30-287-040 C-TR,DTC114TKA C220 87-010-184-080 CHIP CAPACITOR 3300P(K)
87-026-235-080 CHIP-TR,DTC114EK C221 87-010-322-080 C-CAP,S 100P-50 CH
C222 87-010-492-040 CAP,E 0.33-50 GAS
87-026-210-080 CHIP-TR,DTC144EK C223 87-010-067-040 CAP,E 0.1-50 5L
87-A30-299-080 TR,2SB1326
87-A30-282-040 C-TR,DTA114TKA C224 87-010-553-040 CAP,E 47-16 GAS
87-A30-168-010 TR,2SB1566F C225 87-010-805-080 C-CAP,S 1-16 Z F<YU>
89-211-821-080 CHIP-TR 2SB1182Q C225 87-010-184-080 C-CAP,S 3300P-50 K B C2012<YL>
C226 87-010-497-040 CAP,E 4.7-35 GAS
89-423-953-010 TR,2SD2395F C227 87-010-555-040 CAP,E 100-10 GAS
87-A30-301-080 TR,2SD1862
87-A30-449-040 C-TR,DTA123YKA C228 87-016-669-080 CHIP CAPACITOR,0.1-25
C229 87-010-498-040 CAP,E 10-16 GAS
C230 87-016-669-080 CHIP CAPACITOR,0.1-25
DIODE C231 87-010-555-040 CAP,E 100-10 GAS
C232 87-016-669-080 CHIP CAPACITOR,0.1-25
87-A40-250-080 CHIP-DIODE,DAN202K
87-001-783-080 DIODE,1N4002 C233 87-010-555-040 CAP,E 100-10 GAS
87-020-331-080 CHIP-DIODE,DAN202K C234 87-010-193-080 CHIP CAPACITOR,0.033
87-A40-624-080 ZENER,MTZJ10A C235 87-010-992-080 CAP, CHIP 0.047
87-A40-523-080 ZENER,MTZJ9.1B C236 87-010-067-040 CAP,E 0.1-50 5L
C237 87-010-553-040 CAP,E 47-16 GAS
87-070-136-080 ZENER,MTZJ5.1B
87-017-932-080 ZENER,MTJ6.2B C238 87-010-197-080 CAP, CHIP 0.01 DM
87-A40-798-010 DIODE,1N5402 (3A/200V) C240 87-016-669-080 C-CAP,S 0.1-25 K B
87-A40-817-040 C-ZENER,STZ6.8N C250 87-016-669-080 CHIP CAPACITOR,0.1-25<YU>
C250 87-010-805-080 C-CAP,S 1-16 Z F<YL>
C251 87-010-555-040 CAP,E 100-10 GAS
MAIN C.B
C256 87-010-186-080 CAP,CHIP 4700P
C101 87-010-178-080 CHIP CAP 1000P C258 87-010-150-080 C-CAP,S 6P-50 D CH
C102 87-010-197-080 CAP, CHIP 0.01 DM C259 87-010-316-080 C-CAP,S 33P-50 CH
C103 87-010-495-040 CAP,E 2.2-50 GAS C261 87-012-156-080 C-CAP,S 220P-50 J CH GRM
C106 87-010-322-080 C-CAP,S 100P-50 CH C262 87-016-669-080 C-CAP,S 0.1-25 K B
C107 87-010-552-040 CAP,E 22-16 GAS
C263 87-010-555-040 CAP,E 100-10 GAS
C108 87-010-322-080 C-CAP,S 100P-50 CH C264 87-010-555-040 CAP,E 100-10 GAS
C109 87-010-553-040 CAP,E 47-16 GAS C265 87-016-669-080 C-CAP,S 0.1-25 K B
C110 87-010-198-080 CAP, CHIP 0.022 C266 87-016-669-080 C-CAP,S 0.1-25 K B
C111 87-010-553-040 CAP,E 47-16 GAS C267 87-010-498-040 CAP,E 10-16 GAS
C112 87-010-185-080 C-CAP,S 3900P-50 B
C268 87-010-498-040 CAP,E 10-16 GAS
C113 87-010-197-080 CAP, CHIP 0.01 DM C269 87-010-180-080 C-CER 1500P
C114 87-010-197-080 CAP, CHIP 0.01 DM C270 87-010-180-080 C-CER 1500P
C115 87-010-196-080 CHIP CAPACITOR,0.1-25 C271 87-010-154-080 CAP CHIP 10P
C116 87-010-196-080 CHIP CAPACITOR,0.1-25 C272 87-010-154-080 CAP CHIP 10P
C131 87-012-365-080 C-CAP,S 0.027-25VBK<YU>
C273 87-010-494-040 CAP,E 1-50 M 5L SRE
C131 87-010-220-080 C-CAP,S 0.018-25 K B<YL> C274 87-010-494-040 CAP,E 1-50 M 5L SRE
C132 87-012-365-080 C-CAP,S 0.027-25VBK<YU> C280 87-A10-189-040 CAP,E 220-10
C132 87-010-220-080 C-CAP,S 0.018-25 K B<YL> C281 87-010-555-040 CAP,E 100-10 GAS
C133 87-012-358-080 C-CAP,S 0.47-10 F Z C282 87-016-669-080 C-CAP,S 0.1-25 K B
C134 87-012-358-080 C-CAP,S 0.47-10 F Z
C301 87-010-498-040 CAP,E 10-16 GAS
C161 87-010-196-080 CHIP CAPACITOR,0.1-25 C302 87-010-498-040 CAP,E 10-16 GAS
C171 87-010-197-080 CAP, CHIP 0.01 DM<YU> C303 87-010-494-040 CAP,E 1-50 GAS
C173 87-010-322-080 C-CAP,S 100P-50 J CH GRM C304 87-010-494-040 CAP,E 1-50 GAS
C176 87-010-197-080 C-CAP,S 0.01-25 K B<YL> C305 87-010-184-080 CHIP CAPACITOR 3300P(K)
C201 87-010-553-040 CAP,E 47-16 GAS
C306 87-010-184-080 CHIP CAPACITOR 3300P(K)
C202 87-010-553-040 CAP,E 47-16 GAS C307 87-010-198-080 CAP, CHIP 0.022
C203 87-010-178-080 CHIP CAP 1000P C308 87-010-198-080 CAP, CHIP 0.022
C204 87-016-669-080 C-CAP,S 0.1-25 K B C309 87-010-498-040 CAP,E 10-16 GAS
C310 87-010-498-040 CAP,E 10-16 GAS

-4-
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C311 87-A11-177-080 C-CAP,S 0.15-16 K B C832 87-010-494-040 CAP,E 1-50 M 5L SRE
C312 87-A11-177-080 C-CAP,S 0.15-16 K B C835 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C313 87-A11-177-080 C-CAP,S 0.15-16 K B C836 87-010-182-080 C-CAP,S 2200P-50 K B C2012
C314 87-A11-177-080 C-CAP,S 0.15-16 K B C881 87-010-182-080 C-CAP,S 2200P-50 B
C315 87-010-498-040 CAP,E 10-16 GAS C882 87-010-182-080 C-CAP,S 2200P-50 B

C316 87-010-498-040 CAP,E 10-16 GAS C883 87-010-182-080 C-CAP,S 2200P-50 B

C321 87-010-196-080 CHIP CAPACITOR,0.1-25 C884 87-010-182-080 C-CAP,S 2200P-50 B
C322 87-010-555-040 CAP,E 100-10 GAS CON201 87-A60-859-010 CONN,12P TKC-F12X-K1
C323 87-010-196-080 CHIP CAPACITOR,0.1-25 CON202 87-A60-860-010 CONN,14P TKC-F14X-K1
C324 87-010-498-040 CAP,E 10-16 GAS CON851 88-KTA-603-010 CONN,15P CAM-B68

C331 87-012-358-080 C-CAP,S 0.47-10 F Z CON881 8Z-KT1-611-010 CONN,16P CAM-B51

C332 87-012-358-080 C-CAP,S 0.47-10 F Z ! F881 8Z-KC1-621-010 FUSE,15A 32V
C333 87-010-196-080 C-CAP,S 0.1-25 Z F C2012 J101 8Z-KT1-614-010 ANT,AW-002
C334 87-010-196-080 CHIP CAPACITOR,0.1-25 J451 87-A61-225-010 JACK,PIN 2P<EXCEPT X307,X407>
C351 87-010-494-040 CAP,E 1-50 GAS J451 87-A61-224-010 JACK,PIN 4P XR-401<X307,X407>

C352 87-010-494-040 CAP,E 1-50 GAS L101 87-003-143-080 COIL 4.7 UH

C353 87-010-494-040 CAP,E 1-50 GAS L102 8Z-KT1-619-010 COIL,68MH K7-D
C354 87-010-494-040 CAP,E 1-50 GAS L465 87-003-143-080 COIL,4.7UH K LAL02
C361 87-012-358-080 C-CAP,S 0.47-10 F Z L671 87-003-149-080 COIL,47UH
C362 87-012-358-080 C-CAP,S 0.47-10 F Z L831 87-003-143-080 COIL,4.7UH K LAL02

C363 87-012-358-080 C-CAP,S 0.47-10 F Z L881 8Z-KT1-615-010 FLTR,AMORPHOUS -CHOKE

C364 87-012-358-080 C-CAP,S 0.47-10 F Z LED702 87-027-262-010 LEDE,TLR124(RED)
C365 87-010-175-080 CAP 560P R241 87-022-371-080 C-RES,S 330K-1/10W F
C366 87-010-175-080 CAP 560P R242 87-022-371-080 C-RES,S 330K-1/10W F
C367 87-010-175-080 CAP 560P SW701 87-A91-070-010 SW,TACT SKHHLV

C368 87-010-175-080 CAP 560P SW702 87-A91-152-010 SW,SL 1-1-2 SSSS212-11-A

C451 87-010-498-040 CAP,E 10-16 GAS<X307,X407> TU101 8A-KC8-621-010 TU UNIT, FAE347-A12
C452 87-010-498-040 CAP,E 10-16 GAS<X307,X407> X201 81-592-641-010 VIB,CER 16.93MHZ
C453 87-010-498-040 CAP,E 10-16 GAS X701 87-A70-175-010 VIB,XTAL 4.5MHZ AT-49
C454 87-010-498-040 CAP,E 10-16 GAS

C455 87-012-140-080 CAP 470P<X307,X407> FRONT C.B

C456 87-012-140-080 CAP 470P<X307,X407>
C457 87-012-140-080 CAP 470P C901 87-010-805-080 CAP, S 1-16
C458 87-012-140-080 CAP 470P C902 87-010-194-080 CAP, CHIP 0.047
C511 8A-KC7-623-000 CAP,E 2200U-16 BT(125C) C903 87-010-194-080 CAP, CHIP 0.047
C904 87-010-177-080 C-CAP,S 820P-50 SL
C512 87-010-196-080 CHIP CAPACITOR,0.1-25 C905 87-010-196-080 CHIP CAPACITOR,0.1-25
C513 87-010-196-080 CHIP CAPACITOR,0.1-25
C514 87-010-498-040 CAP,E 10-16 GAS C971 87-010-196-080 CHIP CAPACITOR,0.1-25<X407>
C515 87-010-494-040 CAP,E 1-50 GAS CON901 88-KTA-602-010 CONN,15P CAM-B67
C516 87-010-178-080 CHIP CAP 1000P LCD901 8A-KCG-610-010 LCD,AKC-16-17
LED951 87-017-827-070 C-LED,SEC1201 RED
C517 87-010-178-080 CHIP CAP 1000P LED952 87-017-827-070 C-LED,SEC1201 RED
C519 87-010-494-040 CAP,E 1-50 M 5L SRE
C519 87-010-494-040 CAP,E 1-50 M 5L SRE LED953 87-017-827-070 C-LED,SEC1201 RED
C531 87-012-368-080 C-CAP,S 0.1-50 Z F<YL> LED961 87-A40-813-040 C-LED,SEC1E01C BLUE
C532 87-012-368-080 C-CAP,S 0.1-50 Z F<YL> LED962 87-A40-813-040 C-LED,SEC1E01C BLUE
LED963 87-A40-813-040 C-LED,SEC1E01C BLUE
C533 87-012-368-080 C-CAP,S 0.1-50 Z F<YL> PL901 8Z-KT1-641-010 LAMP,T-3
C534 87-012-368-080 C-CAP,S 0.1-50 Z F<YL>
C590 87-010-178-080 CHIP CAP 1000P PL902 8Z-KT1-641-010 LAMP,T-3
C611 87-010-553-040 CAP,E 47-16 GAS SW901 87-036-251-080 SW,T CT 6X3.5 160
C612 87-010-198-080 CAP, CHIP 0.022 SW902 87-036-251-080 SW,T CT 6X3.5 160
SW903 87-036-251-080 SW,T CT 6X3.5 160
C613 87-016-044-040 CAP,E 100-16 GAS SW904 87-A90-001-080 C-SW,TACT SKQMAL
C621 87-010-553-040 CAP,E 47-16 GAS
C622 87-010-553-040 CAP,E 47-16 GAS SW905 87-A90-001-080 C-SW,TACT SKQMAL
C641 87-010-196-080 CHIP CAPACITOR,0.1-25 SW906 87-A90-001-080 C-SW,TACT SKQMAL
C642 87-010-196-080 CHIP CAPACITOR,0.1-25 SW907 87-036-251-080 SW,T CT 6X3.5 160
SW908 87-036-251-080 SW,T CT 6X3.5 160
C671 87-010-198-080 CAP, CHIP 0.022 SW910 87-A90-001-080 C-SW,TACT SKQMAL
C672 87-010-555-040 CAP,E 100-10 GAS
C673 87-010-553-040 CAP,E 47-16 GAS SW911 87-036-251-080 SW,T CT 6X3.5 160
C674 87-010-198-080 CAP, CHIP 0.022 SW913 87-036-251-080 SW,T CT 6X3.5 160
C681 87-010-553-040 CAP,E 47-16 GAS SW914 87-036-251-080 SW,T CT 6X3.5 160
SW915 87-036-251-080 SW,T CT 6X3.5 160
C682 87-010-198-080 CAP, CHIP 0.022 SW916 87-036-251-080 SW,T CT 6X3.5 160
C701 87-010-315-080 C-CAP,S 27P-50 CH
C702 87-010-314-080 C-CAP,S 22P-50V SW917 87-036-251-080 SW,T CT 6X3.5 160
C706 87-010-497-040 CAP,E 4.7-35 GAS SW918 87-036-251-080 SW,T CT 6X3.5 160
C711 87-010-322-080 C-CAP,S 100P-50 CH SW921 87-A91-597-010 SW,RTRY SIM-026MT

C712 87-010-322-080 C-CAP,S 100P-50 CH

C761 87-010-555-040 CAP,E 100-10 GAS AUX C.B
C763 87-010-196-080 CHIP CAPACITOR,0.1-25
C771 87-012-156-080 C-CAP,S 220P-50 J CH GRM FC901 8A-KC7-611-010 F-CABLE,3P (AUX)
C831 87-010-494-040 CAP,E 1-50 M 5L SRE J901 85-HRL-623-010 JACK,3.5 ST BLK

-5-
 CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

TRANSISTOR ILLUSTRATION

B
B
E E C B E E C B B C E

2SA1037 2SB1326 2SB1182 2SB1566 2SD2395

2SC2412 2SD1862
DTA114TKA
DTA123YKA
DTC114EK
DTC114YKA
DTC114TKA
DTC144EK

-6-
WIRING - 1 (YU: MAIN) 1 / 2
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

-7-
WIRING - 1 (YU: MAIN) 2 / 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

-8-
SCHEMATIC DIAGRAM - 1 (YU: MAIN 1 / 2)

-9-
SCHEMATIC DIAGRAM - 2 (YU: MAIN 2 / 2)

-10-
WIRING - 2 (YL: MAIN) 1 / 2
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

-11-
WIRING - 2 (YL: MAIN) 1 / 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

-12-
SCHEMATIC DIAGRAM - 3 (YL: MAIN 1 / 2)

-13-
SCHEMATIC DIAGRAM - 4 (YL: MAIN 2 / 2)

-14-
WIRING - 3 (FRONT)

A
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A

-15-
SCHEMATIC DIAGRAM - 5(FRONT)

-16-
IC BLOCK DIAGRAM
IC,LA4743B

IC,LA6556

-17-
VOLTAGE CHART
IC, LC72358N-9910
PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V) PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
1 2.45 2.47 2.35 2.35 2.42 2.28 68 4.94 4.95 4.76 4.76 4.87 4.79
2~6 0 0 0 0 0 0 69 0 0 0.58 0.57 0 0.59
7 4.87 4.91 4.85 4.84 4.90 4.87 70 0 0 2.51 2.51 0 2.52
8 0 0 0.05 0.05 0.15 0.03 71 ~ 72 0 0 0 0 0 0
9 0.10 0.10 0.20 0.21 0.70 0.21 73 4.98 4.97 4.80 4.80 4.91 4.84
10 0.10 0.10 0.22 0.21 0.75 0.24 74 0 0 0 2.34 0 2.31
11 0 0 0 0 0.03 0 75 0 0 2.45 0.01 0 0.03
12 0 0 0 0 0 0 76 0 0 0 0 0 0
13 0 0 0 0 4.83 0 77 0 0 0.08 0.08 0 0
14 0 0 4.57 4.54 0 0 78 0 0 1.04 1.04 1.05 0
15 ~ 16 0 0 0 0 0 0 79 0 0 0 0 0 0
17 0 0 0 0 4.78 0 80 2.53 2.52 2.45 2.46 2.50 2.47
18 0 0 4.72 4.72 0 0
19 ~ 30 0 0 0 0 0 0
31 4.98 5.00 4.79 4.85 4.91 4.85
32 ~ 38 0 0 0 0 0 0
IC, LA4743B
39 0 0 0 0 4.84 0
40 0 0 4.72 4.72 4.84 4.79 PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
41 0 0 4.72 4.73 4.83 4.79 1~2 0 0 0 0 0 0
42 0 0 4.74 4.74 4.85 4.80 3 0 0 2.75 2.74 2.74 2.74
43 0 0 4.78 4.77 4.89 4.84 4 0 0 4.76 4.82 4.83 4.84
44 0 0 0 0 0 0 5 0 0 2.74 2.74 2.75 2.75
45 4.46 4.49 4.44 4.45 4.52 4.46 6 14.40 14.40 14.38 14.38 14.38 14.38
46 0 0 0 0 4.84 0 7 0 0 2.75 2.74 2.74 2.74
47 0 0 0 0 2.00 0 8 0 0 0 0 0 0
48 0 0 0 0 0 0 9 0 0 2.68 2.73 2.73 2.74
49 0 0 0 0 4.89 0 10 0 0 13.17 13.15 13.16 13.16
50 0 0 0 0 0 0 11 0 0 3.04 3.07 3.07 3.08
51 4.86 4.90 4.89 4.89 0 4.87 12 0 0 3.09 3.11 3.11 3.11
52 0 0 0 0 4.94 0 13 0 0 0 0 0 0
53 4.78 / 0 4.78 / 0 4.75 / 0 4.75 / 0 4.75 / 0 4.75 / 0 14 0 0 3.09 3.11 3.11 3.11
54 4.80 / 0 4.80 / 0 4.77 / 0 4.77 / 0 4.77 / 0 4.75 / 0 15 0 0 3.04 3.07 3.07 3.08
55 4.87 4.90 4.86 4.86 4.90 4.84 16 0 0 2.29 2.40 2.41 2.40
56 4.82 / 4.78 4.82 / 4.78 4.70 / 4.75 4.70 / 4.75 4.70 / 4.75 4.72 / 4.75 17 0 0 2.71 2.74 2.74 2.74
57 3.40 3.44 3.44 3.44 3.50 3.41 18 0 0 0 0 0 0
58 ~ 60 0 0 0 0 0 0 19 0 0 2.73 2.74 2.74 2.74
61 4.86 4.89 4.88 4.87 4.93 4.87 20 14.40 14.40 14.38 14.38 14.38 14.35
62 ~ 64 0 0 0 0 0 0 21 0 0 2.76 2.73 2.73 2.73
65 3.31 3.32 3.31 3.32 3.32 3.31 22 0 0 4.54 4.55 4.58 4.56
66 4.94 4.96 4.78 4.78 4.87 4.79 23 0 0 2.72 2.76 2.76 2.77
67 0 0 4.63 4.62 4.61 4.62 24 ~ 25 0 0 0 0 0 0

-18-
IC, LA9241ML
PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V) PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
1~2 0 0 0 0 2.50 0 60 0 0 0 0 0 0
3 0 0 0 0 2.53 0 61 0 0 0 0 2.22 0
4 0 0 0 0 2.49 0 62 0 0 0 0 3.71 0
5~7 0 0 0 0 2.51 0 63 0 0 0 0 0.19 0
8 0 0 0 0 2.52 0 64 0 0 0 0 4.91 0
9 ~ 12 0 0 0 0 2.51 0
13 0 0 0 0 2.50 0
14 0 0 0 0 2.51 0
15 0 0 0 0 2.50 0
16 0 0 0 0 2.61 0
17 0 0 0 0 2.52 0 IC, LA6556
18 0 0 0 0 2.42 0
PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
19 0 0 0 0 2.52 0
1~2 0 0 0 0 0 0
20 0 0 0 0 2.53 0
3 0 0 0 0 8.44 0
21 0 0 0 0 2.51 0
4~5 0 0 0 0 0 0
22 ~ 23 0 0 0 0 0 0
6 0 0 0 0 3.70 0
24 ~ 25 0 0 0 0 2.47 0
7 0 0 0 0 4.06 0
26 ~ 28 0 0 0 0 0 0
8 0 0 0 0 3.76 0
29 0 0 0 0 2.63 0
9 0 0 0 0 4.05 0
30 0 0 0 0 2.37 0
10 0 0 0 0 3.86 0
31 ~ 33 0 0 0 0 0 0
11 0 0 0 0 3.88 0
34 0 0 0 0 4.93 0
12 0 0 0 0 3.60 0
35 0 0 0 0 0 0
13 0 0 0 0 4.20 0
36 0 0 0 0 1.0 0
14 0 0 0 0 8.45 0
37 ~ 39 0 0 0 0 0 0
15 0 0 0 0 2.38 0
40 0 0 0 0 0.50 0
16 ~ 17 0 0 0 0 0 0
41 0 0 0 0 2.29 0
18 ~ 22 0 0 0 0 2.51 0
42 0 0 0 0 2.40 0
23 0 0 0 0 2.45 0
43 0 0 0 0 2.41 0
24 ~ 25 0 0 0 0 2.51 0
44 0 0 0 0 2.50 0
26 0 0 0 0 7.85 0
45 ~ 46 0 0 0 0 2.51 0
27 0 0 0 0 4.98 0
47 0 0 0 0 2.41 0
28 0 0 0 0 2.51 0
48 ~ 49 0 0 0 0 0 0
' 29 0 0 0 0 8.44 0
50 0 0 0 0 2.41 0
30 ~ 32 0 0 0 0 2.51 0
51 0 0 0 0 4.80 0
33 0 0 0 0 2.43 0
52 ~ 53 0 0 0 0 0 0
34 ~ 35 0 0 0 0 4.91 0
54 0 0 0 0 4.84 0
36 0 0 0 0 0 0
55 0 0 0 0 0 0
56 0 0 0 0 4.93 0
57 ~ 58 0 0 0 0 2.51 0
59 0 0 0 0 2.39 0

-19-
IC, LC78622NE
PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V) PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
1 0 0 0 0 0.05 0 59 0 0 0 0 0 0
2 0 0 0 0 0 0 60 0 0 0 0 1.93 0
3 0 0 0 0 1.55 0 61 0 0 0 0 2.34 0
4 0 0 0 0 0 0 62 ~ 64 0 0 0 0 0 0
5 0 0 0 0 1.77 0
6 0 0 0 0 4.69 0
7 0 0 0 0 0.33 0
8 0 0 0 0 0 0
TU UNIT, FAE347-A12
9 0 0 0 0 2.49 0
10 0 0 0 0 2.39 0 PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
11 0 0 0 0 0 0 1~2 0 0 0 0 0 0
12 0 0 0 0 0.50 0 3 0 0 0 0.02 0 0
13 ~ 17 0 0 0 0 0 0 4 0 0 6.89 0 6.93 0
18 0 0 0 0 4.92 0 5 0 0 0 0 0 0
19 ~ 20 0 0 0 0 0 0 6 0 0 3.42 3.42 3.42 3.42
21 0 0 0 0 2.35 0 7~8 0 0 0 0 0 0
22 ~ 23 0 0 0 0 4.93 0 9 0 0 0 7.95 0 7.85
24 ~ 30 0 0 0 0 0 0 10 ~ 11 0 0 0 0 0 0
31 0 0 0 0 2.47 0 12 0 0 7.27 0 7.31 0
32 ~ 36 0 0 0 0 0 0 13 0 0 7.58 7.49 7.61 7.46
37 0 0 0 0 2.03 0 14 0 0 3.41 3.42 3.42 3.42
38 ~ 39 0 0 0 0 0 0 15 0 0 0 0 0 0
40 0 0 0 0 2.03 0 16 0 0 3.41 3.44 3.39 3.42
41 0 0 0 0 4.96 0 17 0 0 3.36 3.41 3.39 3.42
42 0 0 0 0 4.92 0 18 ~ 19 0 0 0 0 0 0
43 0 0 0 0 4.79 0 20 0 0 0.01 0.01 0 0
44 0 0 0 0 1.75 0 21 0 0 5.74 3.66 0.43 0
45 0 0 0 0 1.85 0 22 0 0 4.55 4.56 4.56 4.54
46 0 0 0 0 0 0 23 0 0 1.07 0.63 0.05 0.04
47 0 0 0 0 0.10 0 24 0 0 4.07 1.21 4.01 1.21
48 0 0 0 0 0.02 0 25 0 0 7.58 7.50 7.61 7.46
49 0 0 0 0 0.11 0 26 0 0 0 0.03 2.05 0.03
50 0 0 0 0 2.47 0
51 0 0 0 0 0 0
52 0 0 0 0 2.46 0
53 0 0 0 0 2.0 0
54 0 0 0 0 0 0
55 0 0 0 0 0.04 0
56 0 0 0 0 0 0
57 0 0 0 0 4.80 0
58 0 0 0 0 4.88 0

-20-
IC, LC75374E IC, LC75853NW
PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V) PIN NO. BU (V) BU+ACC (V) FM (V) AM(V) CD (V) AUX (V)
1 0 0 3.94 3.93 3.96 3.96 1 0 0 4.84 4.83 4.86 4.85
2 0 0 3.98 3.98 4.00 4.01 2 0 0 0 0 0 0
3 0 0 4.00 4.00 4.02 4.01 3 2.50 2.50 2.47 2.47 2.48 2.48
4~6 0 0 4.00 4.00 4.02 4.02 4 2.50 2.50 2.47 2.47 2.48 2.47
7 0 0 3.99 3.99 4.01 3.99 5 2.50 2.50 2.47 2.47 2.48 2.48
8~9 0 0 0 0 0 0 6 2.50 2.50 2.47 2.47 2.48 2.47
10 0 0 3.98 3.98 4.00 3.99 7 ~ 10 2.50 2.50 2.47 2.46 2.47 2.47
11 0 0 4.01 4.01 4.03 4.01 11 ~ 12 2.50 2.50 2.47 2.47 2.47 2.47
12 0 0 3.99 3.99 4.01 3.99 13 2.50 2.50 2.47 2.46 2.47 2.47
13 0 0 4.02 4.01 4.04 4.01 14 2.50 2.50 2.47 2.47 2.48 2.47
14 0 0 4.01 4.01 4.03 4.01 15 ~ 16 2.50 2.50 2.47 2.47 2.47 2.47
15 ~ 18 0 0 0 0 0 0 17 2.50 2.50 2.47 2.47 2.48 2.47
19 0 0 4.01 4.01 4.03 4.01 18 ~ 19 2.50 2.50 2.47 2.47 2.47 2.47
20 ~ 21 0 0 4.02 4.01 4.04 4.01 20 ~ 23 2.50 2.50 2.47 2.47 2.48 2.47
22 0 0 4.01 4.01 4.03 3.98 24 ~ 25 2.50 2.50 2.47 2.47 2.47 2.47
23 0 0 4.01 4.01 4.03 4.01 26 ~ 29 2.50 2.50 2.47 2.47 2.48 2.47
24 0 0 3.98 3.98 4.00 3.98 30 2.50 2.50 2.47 2.46 2.47 2.47
25 ~ 26 0 0 0 0 0 0 31 ~ 32 2.50 2.50 2.49 2.47 2.48 2.47
27 0 0 4.02 3.99 4.04 3.99 33 ~ 40 2.50 2.50 2.48 2.47 2.48 2.47
28 0 0 4.02 4.01 4.04 4.01 41 2.50 2.50 2.48 2.46 2.47 2.47
29 0 0 4.02 4.01 4.04 4.01 42 2.50 2.50 2.48 2.47 2.47 2.47
30 ~ 31 0 0 4.01 4.01 4.03 4.00 43 2.50 2.50 2.48 2.46 2.48 2.46
32 0 0 4.00 3.99 4.02 3.98 44 4.96 4.96 4.95 4.92 4.93 4.91
33 0 0 3.91 3.91 3.93 3.93 45 4.96 4.96 4.95 4.93 4.93 4.91
34 0 0 4.02 4.01 4.04 4.02 46 4.96 4.96 4.95 4.92 4.93 4.91
35 0 0 4.00 3.99 4.02 4.00 47 ~ 49 4.96 4.96 4.95 4.92 4.93 4.91
36 0 0 0 0 0 0 50 ~ 55 0 0 0 0 0 0
37 ~ 38 0 0 4.00 3.99 4.02 4.00 56 4.99 4.99 4.95 4.92 4.93 4.91
39 0 0 7.64 7.63 7.68 7.64 57 3.33 3.33 3.32 3.29 3.30 3.28
40 0 0 4.00 3.99 4.02 4.00 58 1.67 1.67 1.67 1.65 1.66 1.65
41 0 0 3.99 3.99 4.01 3.99 59 0 0 0 0 0 0
42 0 0 0 0 0 0 60 3.91 3.91 3.88 3.88 3.88 3.87
43 0 0 4.00 3.99 4.02 3.99 61 4.96 4.96 4.92 4.86 4.88 4.86
44 0 0 4.03 4.02 4.05 4.01 62 0 0 0.25 0.24 0.77 0.24
63 0 0 0.25 0.20 0.67 0.24
64 0 0 0.04 0.03 0.18 0.03

-21-
IC DESCRIPTION
IC, LC72358N-9910
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 XIN I System clock oscillator input. 48 RWC O Read / write control output terminal.
2~3 NC - Not connected. 49 CD RES O DSP reset output terminal.
4 E-VOL DO O Data output for electric volume. 50 SW3 I Disc detection / chuck or release disc detection.
5 E-VOL CLO O Clock output for electric volume. 51 SW2 I 12 cm disc detection / 12 cm disc ejection end detection.
6 E-VOL CE O CE output for electric volume. 52 SW1 I Leading motor start detection.
7 LCD DI I LCD driver data signal input. 53 R-ENCOD2 I Rotary encoder input 2.
8 LCD DO O LCD driver data signal output. 54 R-ENCOD1 I Rotary encoder input 1.
9 LCD CLO O LCD driver clock signal output. 55 LCD-DI I LCD driver data signal input.
10 LCD CE O LCD driver CE signal output. 56 REMOTE IN I Remote controller input. Pulled up when not used.
11 SQ OUT I Sub-code Q input terminal. 57 LED O Security LED flashing output. H: No light on, L: Light on.
12 COIN O Command output terminal for DSP. 58 ~ 60 NC - Not connected.
Transfer-out clock for command output or output terminal for Sub-code transfer-in 61 INSIDE I Pick up inner track position detection.
13 CQCK O
clock from SQ OUT. 62 TEST I CD test mode. Pulled down when not used.
Stereo signal input when receiving. Hi=MONO, Low=ST FM reception. 63 NC - Not connected.
14 SD/ST I
Channel detection signal input when FM/AM seeking. Hi=detect channel 64 L IND I Voltage input for level indecator. Pulled down when not used.
15 LOC/DX O LOC/DX switching output when in the radio seek mode. Hi=LOC, Low=DX 65 PH.MUTE I External mute control. Low=-20dB mute. Pulled up when not used.
16 IF REQ O IF count signal request output. 66 RESET I System reset. Low= system reset.
17 BAND O FM/AM power switch output. Hi=AM, Low=FM 67 HOLD I ACC (accessory power) ON/ OFF input. OFF=fault mode.
18 TU ON O Radio power switch output. Hi=Radio mode 68 SNS I Backup detection.
19 ~ 21 NC - Not connected. 69 NC - Not connected.
22 ~ 23 KS4 ~ KS3 O Initial setting diode matrix output(Not used). 70 IF I IF count signal input (FM / AM).
24 ~ 26 KS2 ~ KS0 O Initial setting diode matrix output. 71 EO3 - Not used.
27 ~ 30 K3 ~ K0 I Initial setting diode matrix input. 72 SUBPD - Not used.
31 VDD - Power supply. 73 VDD - Power supply.
32 NC - Not connected. 74 AM OSC I AM channel transmission input.
33 LM+ O Loading motor control terminal. 75 FM OSC I FM channel transmission input.
34 LM- O Loading motor control terminal. 76 VSS - Connected to GND.
35 FEM+ O Thread motor control terminal. 77 EO2 O Not used.
36 FEM- O Thread motor control terminal. 78 EO1 O Error out from charge pump (for FM / AM).
37 RW O RW disc control. Normal set to "Hi". Hi=NORMAL DISC, Low=RW DISC 79 NC - Not connected.
38 LP UP O RW disc control. Normal set to "Lo". Hi=Disable playback even though 80 XOUT O System clock oscillator output.
39 CD ON O CD power switch output. Hi=CD mode RW port is low
40 A-MUTE O Audio mute signal output.
41 POWER CONT O Power control signal output.
42 ST-BY MUTE O ST-BY mute signal output.
43 POWER MUTE O Power mute signal output.
44 BEEP O BEEP output(3 kHz, 50 ms).
45 DFP IN I Front panel detection.
46 DRF I "Detect RF" RF level detection input. Pulled up when not used.
47 WRQ I Sub-code Q output standby input terminal.

-22-
IC, LA9241ML
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description

For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF The HFL (high frequency level) signal is used to judge whether the main beam is
1 FIN2 O 37 HFL O
signal and subtraction from it create an EF signal. positioned on the pit or on the mirror.

2 FIN1 O For the connection of the pickup photodiode. 38 SLOF I Sled servo off control input.

For the connection of the pickup photodiode. Subtraction from the F pin creates a TE 39 CV- I CLV error signal input from the DSP.
3 E O
signal. 40 CV+

4 F O For the connection of the pickup photodiode. 41 RFSM O RF output.

5 TB I Inputs the DC components in the TE signal. Sets the RF gain and the EFM singal's 3T compensation constant togther with the
42 RFS- O
For the connection of a resistor which sets the gain of the TE signal between this pin RFSM pin.
6 TE- O
and the TE pin. The SLC (slice level control) signal is output to control the DSP's data slice level of the
43 SLC O
7 TE O TE signal output. RF waveform.

8 TESI I TES (track error sense) comparator input. The signal is passed through a BPF. 44 SL1 I Input to control the DSP's data slice level.

9 SCI I Shock detection input. 45 D-GND - Ground of digital signals.

10 TH I Sets the time constant for the tracking gain. 46 FSC O Output for the focus search smoothing capacitor.

11 TA O TA amp output. 47 TBC I The TBC (tracking balance control) signal sets the EF balance variation range.

12 TD- I Composes the tracking phase compensation constant between the TD and VR pins. 48 NC - Not connected.

13 TD I Sets the tracking phase compensation. 49 DEF O Disc defect detection output.

14 JP I Sets the amplitude of the tracking jump signal (kick pulses). 50 CLK I Reference clock input. 4.23 MHz is input from the DSP.

15 TO O Tracking control signal output. 51 CL I Microprocessor command clock input.

16 FD O Focusing control signal output. 52 DAT I Microprocessor command data input.

17 FD- I Composes the focusing phase compensation constant between the FD and FA pins. 53 CE I Microprocessor chip enable input.

18 FA O Composes the focusing phase compensation constant between the FD and FA pins. 54 DRF O DRF (detect RF) is an output to detect the RF level.

19 FA- I Composes the focusing phase compensation constant between the FD and FA pins. The FSS (focus search select) signal switches the focus search modes (+/-search /
55 FSS I
20 FE O FE signal output. +search with respect to the reference voltage). (Not connected)

For the connection of a resistor whichs sets the gain of the FE signal between this pin 56 VCC2 - VCC of servo and digital circuits.
21 FE- I
and the TE pin. 57 REF1 - For the connection of bypass capacitor for the reference voltage.

22 A-GND O Ground of analog signals. 58 VR O Reference voltage output.

23 SP O Single-ended output of the signals input to the CV+ and CV- pins. 59 LF2 - Sets the time constant for disc defect detection.

24 SPI I Spindle amp input. 60 PH1 - For the connection of a capacitor to hold the RF signal peak.

25 SPG I For the connection of a resistor which sets the gain in the spindle 12cm mode. 61 BH1 - For the connection of a capacitor to hold the RF signal bottom.

26 SP- I For the connection of the spindle phase compensation constant with the SPD pin. 62 LDD O APC circuit output.

27 SPD O Spindle control signal output. 63 LDS I APC circuit input.

28 SLEQ I For the connection of sled phase compensation constant. 64 VCC1 - VCC of RF signal circuits.

29 SLD O Sled control signal output.

30 SL-
I Sled feed signal input from the microprocessor.
31 SL+
32 JP-
I Tracking signal input from the DSP.
33 JP+
34 TGL I Tracking gain control signal input from the DSP. Low gain when TGL is "H".
35 TOFF I Tracking off control signal input from the DSP. Off when TOFF is "H".
36 TES O Outputs the TES signal to the DSP.

-23-
IC, LC78622NE
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 DEFI I Defect detection signal (DEF) input. (Must be connected to 0V when unused.) 39 RVSS - Right channel ground. (Must be connected to 0V.)
2 TAI I For PLL/Test input. A pull-down resistor is built-in. (Must be connected to 0V.) 40 RCHO O Right channel output.
3 PDO O External VCO control phase comparator output. 41 RVDD - Right channe power supply.
4 VVSS - Intetnal VCO ground. (Must be connected to 0V.) 42 MUTER/CONT8 O Right channel mute output./ General purpose input/ output.
5 ISET I PDO output current adjustment resistor connection. 43 XVDD - Crystal oscillator power supply.
6 VVDD - Internal VCO power supply. 44 XOUT O
Connections for a 16.9344 MHz crystal oscillator element.
7 FR I VCO frequency range adjustment. 45 XIN I
8 VSS - Digital system ground. (Must be connected to 0V.) 46 XVSS - Crystal oscillator ground. (Must be connected to 0V.)
9 EFMO O Slice level control EFM signal output. 47 SBSY O Subcode clock synchronization signal output.
10 EFMIN I Slice level control EFM signal input. 48 EFLG O C1, C2, sigle an double error correction monitor.
11 TEST2 I Test input. A pull-down resistor is built-in. (Must be connected to 0V.) 49 PW O Subcode P, Q, R, S, T, U and W output.
12 CLV+ Disc motor control output. Can be set to three-value output by microprocessor Subcode frame synchronization signal output. This signal falls when the subcode are
O 50 SFSY O
13 CLV- command. in standby stase.
Rough servo/phase control automatic switching monitor output. Outputs a high level 51 SBCK I Subcode readout clock input. This is a Schmitt input.
14 V/P O
during rough servo a low level. 52 FSX O Output pin for the 7.35 kHZ synchronization signal divided from the crystal oscillator.
15 HFL I Track detection signal input. This is a Schmitt input. 53 WRQ O Subcode Q output standby output.
16 TES I Tracking error signal input. This is a Schmitt input. 54 RWC I Read/write control input. This is a Schmitt input.
17 TOFF O Tracking off output. 55 SQOUT O Subcode Q output.
18 TGL O Tracking gain switching output. Increase the gain when low. 56 COIN I Command input pin from control microprocessor.
19 JP+ Track jump output. Three value output is also possible when specified by0 Input for both the command input acquisition clock and the SQOUT pin subcode
O 57 CQCK I
20 JP- microprocessor command. readout clock input pin. This is Schmitt input.
21 PCK O EFM data playback clock monitor. Output 4.3218 MHz when the phase is locked. 58 RES I Reset input. This pin must be set low briefly after power is first applied.
Synchronization signal detection output. Output a high level when the synchronization 59 TST11 O Test output. Leave open. (Normally output a low level.)
22 FSEQ O signal detected from the EFM signal and the internaly generated synchronization signal 60 16M O 16.9344 MHz output.
range. 61 4.2M O 4.2336 MHz output.
23 VDD - Digital system power supply. 62 TEST5 I Test input. A pull-down resistor is built-in. (Must be connected to 0V.)
24 ~ 28 CONT1 ~ 5 I/O General purpose input/ output pin1 ~ 5. Chip seledt input. A pull-down resistor is built-in.
63 CS I
De-emphasis monitor. A high level indicates playback of a De-emphasis disk./ General (Must be connected to 0V if not controlled.)
29 EMPH/CONT6 O
General purpose input/ output pin6. 64 TEST1 I Test input. No pull-down resistor. (Must be connected to 0V.)
30 C2F O C2 flag output.
31 DOUT O Digital output.
32 TEST3 I Test input. A pull-down resistor is built-in. (Must be connected to 0V.)
33 TEST4 I Test input. A pull-down resistor is built-in. (Must be connected to 0V.)
General purpose input/ output command identifying. A pull-down resistor is built-in.
34 PCCL I "H": Control possible only for the general purpose input/ output port command.
"L": Control possible for all commands.
35 MUTEL/CONT7 O Left channel mute output./ General purpose input/ output pin.
36 LVDD - Left channel power supply.
37 LCHO O Left channel output.
38 LVSS - Left channel groud. (Must be connected to 0V.)

-24-
IC, LC75374E
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 RVRIN I 4dB volume control input. Must be driven at a low impedance. 40 TP(R)
2 RCOM – 1dB volume control common pin. 41 TUN(R)
I Signal input pins.
For the connection of capacitors that compensate for bass and treble in the tone control 42 CD(R)

circuits. 43 AUX(R)
3~5 RT1 ~ RT3 –
A high-frequency compensation capacitors must be connected between T1 and T2. 44 RSELO O Input selector output pin.
A low-frequency compensation capacitors must be connected between T2 and T3.

6 RTOUT O Tone control output.

7 RSIN I Super bass input. Must be driven at a low impedance.
8 NC – Connected to VSS.
9 NC – Not used.
10 ~ 11 RSB1 ~ RSB2 – For the connection of RCH super bass compensation capacitors.
12 RFIN I Fader input. Must be driven at a low impedance.
13 RFOUT
O Fader outputs. The front and rear sides can be attenuated independently.
14 RROUT IC, LC75853NW
15 VSS – Ground. Pin No. Pin Name I/O Description

16 CL 1 ~ 40 S1 ~ S40 O LCD segment output.

I Serial data and clock inputs for control.
17 DI 41 ~ 43 COM1~ COM3 O LCD command driver outputs.

Chip enable. Data is written in the internal latch when the chip enable signal goes "L" 44 ~ 49 KS1 ~ KS6 O Key scan outputs.
18 CE –
from "H", and each analog switch is activated. Data transfer is enabled at "H". 50 ~ 54 KI1 ~ KI5 I Key scan inputs. These pins have build-in pull-down resistor.

Generates a 1/2VDD power source. A capacitor must be connected between VREF and 55 TEST - Test pin. (Connected to GND.)
19 VREF –
VSS as a troubleshooting against power ripples. 56 VDD - Power supply.

20 LROUT Used for applying the LCD drive 2/3 bias voltage externally. (Must be connected to
O Fader outputs. The frount and rear sides can be attenuated independently. 57 VDD1 I
21 LFOUT VDD2 when a 1/2 bias drive scheme is used.)

22 LFIN I Fader input. Must be driven at a low impedance. Used for applying the LCD drive 1/3 bias voltage externally. (Must be connected to
58 VDD2 I
23 ~ 24 LSB2 ~ LSB1 – For the connection of LCH super bass compensation capacitors. VDD1 when a 1/2 bias drive scheme is used.

25 NC – Not used. 59 VSS - Power supply. (Connected to GND.)

26 NC – Connected to VSS. 60 OSC I/O Resistor and capacitor are attached externally form an oscillator circuit.

27 LSIN I Super bass input. Must be driven at a low impedance. 61 DO O Serial data interface pin; output data.

28 LTOUT O Tone control output. 62 CE O Serial data interface pin; chip enable.
63 CL O Serial data interface pin; synchronization.
For the connection of capacitors that compensate for bass and treble in the tone control
circuit. 64 DI O Serial data interface pin; data transferred.
29 ~ 31 LT3 ~ LT1 –
A high-frequency compensation capacitors must be connected between T1 and T2.
A low-frequency compensation capacitors must be connected between T2 and T3.

32 LCOM – 1dB volume control common pin.

33 LVRIN I 4dB volume control input. Must be driven at a low impedance.
34 LSELO O Input selector output pin.
35 AUX(L)
36 CD(L)
I Signal input pins.
37 TUN(L)
38 TP(L)
39 VDD – Power supply.

-25-
LCD DIAGRAM

-26-
CD TEST MODE

1-1 How to Activate CD Test Mode Caution when servicing

(1) How to use extension jig.
1) Connect 62 pin (test) of IC701 (LC72358N-9910) on
Correct between MAIN C.B. and CD mechanisms by extension jigs when checking CD mechanism
MAIN C.B to the 31 pin (VDD) by cable. (TN-CCD1001-113J) operation.
(Refer to the following figure.)

2) Connect wire of ACC (red) and BACKUP (yellow) of power supply/speaker connector to DC+12V,
then connect Ground (black) to -.
When CD test mode is started, all displays will be lighted as shown in the following figure.

1-2 How to cancel CD Test Mode

1) Disconnect the cable of 62 pin (test) and 31 pin (VDD) of the MAIN C.B
IC701 (LC72358N-9910) and switch on the power.

Parts Description AKC-JIG Parts Number SV-J00-075-010

1-3 CD Test Mode Functions

MODE Keys to operate Display Operations Contents

Start Mode All lightented • Start TEST MODE
Search Mode RANDOM TOC • Continual Focus Search • Confirm APC circuit
READING (The pickup lens respeats the • Laser current measurement
full-swing up-down motion) • Confirm focus error waveform
* NOTE 1
Play Mode REP 1 TRACK No. • Normal Play Back • Focus servo
Playing Time Indica- • Focus search is contiuned if • Traking servo
tion Revel/Ing TOC cannot be read • CLV servo
Indication • Sled servo
Traverse INT Track no. & Playing • Pause Status • Traking servo OFF
Mode Time Indication
Thread Mode All lightened • Pick up Move to outer most track • Thread servo
• Pick up Move to inner most track • Confirm mechanism operation
Gain Switch 1 All lightened • Step 1 : For CD/CD-R • Step 1 to 3 are cyclic
(Preset Button) • Step 2 : For CD-R RF Gain is up • “Error 03” is indicated if the Disc
against Step 1 does not Step 1 match.
• Step 3 : For CD-R Laser Power Up
against Step 2
• Do not insert a Disc when confirming Search Mode
• Press PWR button when cancelling Search Mode. Test Mode will be restored when PWR button is
pressed once again.
• Insert the “Test Disc” when operating all modes except search mode.
* NOTE 1 : There are CD operations are disable owing to the protection circuit being operated when heat builds up in the driver IC
if the focus search is operated continually for more than 10 minutes. In cases, the power supply should be switched off
for 10 minutes until heat has been reduced and then re-started.

-27-
MECHANICAL EXPLODED VIEW 1 / 1

40
B

P.C.B A
29
10

A
28
27 41
26 PANEL,
9 25 TN-CCD1001-113J D HT-SINK D D
8 24 D
42
D
11 D
7 28 44
37 E
6
12 P.C.B F
23
13 D
2 D D
1 20
19 22 D
17
3 21
4 39 43
HT-SINK
18
5 16

14 15 38 D
47 P.C.B
33
D

C
G
46
30 A
B 36
34 B

45
35
D
C

32

31

-28-
MECHANICAL PARTS LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-KC7-005-010 KNOB,RTRY -AC 30 8A-KCF-020-010 CABI,TRIM -AC15
2 8A-KC7-020-010 RING,RTRY -AC 31 8Z-KC2-203-210 LEVER,DFP HOOK -C2
3 8A-KC7-220-010 SPR-C,ROTARY -AC 32 8Z-KC2-221-110 SPR-C,DETACH HOOK-C2
4 8A-KCG-004-010 WINDOW,LCD X207<207> 33 8Z-KC2-011-110 CABI,BASE -C2<YU>
4 8A-KCG-003-010 WINDOW,LCD X307<307> 33 8Z-KC2-011-210 CABI,BASE -C2<YL>

4 8A-KCG-005-010 WINDOW,LCD X3070<3070> 34 8Z-KC2-222-010 SPR-T,DETACH LOCK-C2

4 8A-KCG-006-010 WINDOW,LCD X4010<4010> 35 8Z-KC2-204-210 LEVER,DFP LOCK -C2
4 8A-KCG-007-010 WINDOW,LCD X2070<2070> 36 8Z-KC1-231-110 HLDR,HALF-C
4 8A-KCG-008-010 WINDOW,LCD X407<407> 37 8Z-KC1-213-010 CHAS,SIDE L -C
5 8A-KCF-022-010 WINDOW,SIDE R -AC15 38 8Z-KCG-201-210 CHAS,FRONT -C16

6 8A-KCF-021-010 WINDOW,SIDE L -AC15 39 8A-KC7-230-010 HLDR,TR2 -AC

7 8A-KCF-001-010 CABI,FRONT -AC15 40 8Z-KC1-211-010 COVER, TOP -C
8 8A-KC7-014-010 BTN,CLEAR S -AC 41 8Z-KC7-201-010 COVER, ISO BLIND -C
9 8A-KC7-208-010 HLDR,BTN L-AC 42 8Z-KC3-201-010 COVER, CD BLIND -C
10 8A-KCF-211-010 LENS,ENCO -AC15 43 8A-KC7-224-010 HLDR,P-IC -AC

11 8A-KC7-007-010 BTN,SEESAW R -AC 44 8A-KC7-611-010 F-CABLE,3P (AUX)

12 8A-KCF-007-010 BTN,SEESAW L -AC15 45 8Z-KC1-214-010 CHAS,SIDE R -C
13 8A-KC7-006-010 BTN,PRE.-AC 46 8Z-KC1-212-010 COVER, BOTTOM -C
14 8A-KC7-011-010 BTN,CLEAR L -AC 47 8A-KCF-220-010 COVER, DUST DFP-AC
15 8A-KCF-208-010 HLDR,BTN R1 -AC15 A 8Z-KC1-253-010 S-SCREW,PT 2*8 BH+ BLK

16 8A-KC7-013-010 BTN,CLEAR ML -AC B 87-B10-216-010 U+2.6-4.0 ZINC BLK (BH M2.6)

17 8A-KCF-012-010 BTN,CLEAR EJ -AC15 C 8Z-KC1-251-010 S-SCREW,TH2.6-4.0-0.8
18 8A-KCF-210-010 HLDR,BTN R3 -AC15 D 87-251-073-410 SCREW,U+2.6-6
19 8A-KCF-008-010 BTN,MONO -AC15 E 87-251-100-410 U+3-16
20 8A-KCF-010-010 BTN,CLEAR S2 -AC15 F 87-B10-259-010 UT2+3.0-10.0 W/O SLOT (BH TAP)

21 8A-KCF-011-010 BTN,DETACH -AC15 G 87-432-903-010 WASHER,WTE 2.6

22 8Z-KC2-223-010 SPR-C,DETACH -C2
23 8A-KCF-212-010 LENS,R -AC15
24 8A-KCF-215-010 HLDR,LCD -AC15
25 8A-KCG-610-010 LCD,AKC-16-17

26 8A-KCF-213-010 LENS,LCD -AC15

27 8A-KCF-214-010 CASE,LCD LENS -AC15
28 8Z-KT1-236-010 CAP,LAMP BLU<YU>
28 8Z-KT1-239-010 CAP,LAMP BLU B<YL>
29 8A-KCF-002-010 CABI,REAR -AC15

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange

-29-
CD MECHANISM EXPLODED VIEW 1 / 1

5
17 C C B 2
C
1 B
4
16
15
B
5
9 3

11 A
14
7
13
6
A 17
26 28 F
25 31
32 8
12
20 19
20
33
27 21 30
A

24 A D D A
22 A A
23 A 35 34
A
A
18 A
62
63 A
10
67
29
2
54 36

53
67 2

41
38 37
55
56 40
57 50
C
68
58
E
52 59 38
E 40
47
45 39
42
44
51 64 I
H
H
60
I 65 43 49
61 B 66 46 48
G

P.C.B B

-30-
CD MECHANISM PARTS LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 S3-031-010-010 FRAME
2 S3-031-050-240 DAMPER(J) 41 S3-031-050-220 LOCK PIN BL
3 S3-031-010-260 REAR OAMPER BKT(J) 42 S3-031-050-080 PU SHAFT
4 S3-031-010-270 FPC GUIDE 43 S6-901-160-110 PICK-UP OPTIMA-720AIE
5 S3-031-010-290 HUNG UP SP(R) 44 S3-031-050-110 PU M NUT
45 S3-031-050-120 NUT PUSH SPR PL
6 S3-031-010-140 TRIG PL
7 S3-031-010-160 TRIG ARM 46 S3-031-053-030 FEED SCREW ASSY
8 S3-031-010-120 TRIG LVR 47 S3-031-050-040 FD GR BLK
9 S3-031-010-150 TRIG PL SPRING 48 S3-030-050-100 PU GEAR(B)
10 S3-031-113-020 LDG RLR SFT ASSY 49 S6-418-040-040 DET SW ESE11HS2
50 S3-031-053-010 FEED MOTOR ASSY
11 S3-031-010-200 FIX PL(R)
12 S3-031-010-180 FIX ARM(R) 51 S3-031-110-300 FRONT BRKT(J)
13 S3-031-010-210 LDG GR(6) 52 S3-031-110-180 L.P SPRING(L)
14 S3-031-010-220 LDG GR(6)SPRING 53 S3-031-110-080 GR MT BLK
15 S3-031-010-170 FIX ARM(L) 54 S3-031-110-310 LDG ROLLER(S)
55 S3-031-110-100 LDG GR(3)
16 S3-031-010-190 FIX PL(L)
17 S3-031-010-030 DAMPER PIN 56 S3-031-110-090 LDG GR(2)
18 S3-031-010-070 UPPER PL 57 S3-031-110-290 LDG BELT
19 S3-031-010-080 SEL STOP PL 58 S3-031-110-050 SUPPORT PL
20 S3-031-010-330 S ARM SPRING(B) 59 S3-031-113-010 LDG MOTOR ASSY
60 S3-031-110-190 L.P SPRING(R)
21 S3-031-010-100 SEL ARM (R)
22 S3-031-010-250 S.L ARM SPRING 61 S3-031-010-300 LEVER SP
23 S3-031-010-240 S.L ARM 62 S9-W07-350-800 LUMILAR W 2.3-9.8-0.35
24 S3-031-110-240 SW ACTR 63 S3-031-110-120 LDG GR(5)
25 S3-031-110-230 SW PCB 64 S6-815-020-350 CONNECTOR TKC-F14P-J3
65 S6-817-020-240 CONNECTOR 6208010115
26 S6-418-040-020 DET SW ESE22MH1
27 S6-418-040-030 DET SW ESE22MH3 66 S6-815-020-370 CONNECTOR TKC-F12P-J3
28 S3-031-010-090 SEL ARM (L) 67 S9-W03-302-760 NW BLUE 2.9-5-0.3
29 S3-031-050-010 TTB 68 S9-W06-400-300 HLW CUT 1.4-3.2-0.4
30 S3-031-050-130 CLP ARM A 87-841-034-410 CAMERA B TAOPPING SCREW M2-5
B 87-741-033-410 CAMERA SCREW TS.G M2-4
31 S3-031-050-360 STOPPER SPR
32 S3-031-050-230 CLAMPER PLATE C 87-351-549-310 CAMERA B TAPPING SCREW M2-4
33 S3-031-050-150 CLAMPER D 87-267-525-310 CAMERA SCREW M1.7-2.2
34 S3-031-050-140 CLP ARM SPRING E 87-B10-026-010 CAMERA TAPPING SCREW S M1.7-8
35 S3-031-050-250 CLP ARM SPR(L) F 87-078-159-110 CAMERA TAPPING SCREW S 3 M2-2
G 87-067-643-010 CAMERA TAPPING SCREW B 3 M2-10
36 S3-031-053-020 SPINDLE MOTOR ASSY
37 S3-031-050-030 FMB H 87-841-034-410 CAMERA TAPPING SCREW B 3 M2-5
38 S3-031-050-210 LOCK PIN I 87-261-032-410 TAMS SCREW M2-3
39 S3-031-050-100 THRUST SPR
40 S3-031-010-280 HUNG UP SP(F)

-31-
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820572 0251431 Printed in Singapore