Ultrasonic testing Level 3 Video link

1) TCG – Time Corrected Gain ll Difference between DAC and TCG :

https://youtu.be/8xrvS6F1EMU
2) Slag Inclusions Ultrasonic testing indication echo pattern ll Practical UT Level 2
indications: https://youtu.be/oCdWv-I6JYY
3) Part-1 FBH blocks in UT ll Area and distance amplitude FBH Blocks:
https://youtu.be/zo3Gr0E1p-s
4) Part-2 Practical DAC using FBH blocks in UT ll Distance amplitude Flat bottom hole
blocks: https://youtu.be/yl8jgTeXwgY
5) Basics of TOFD Part-1 ll Setup and configuration of "Time of flight diffraction"
technique: https://youtu.be/zQXQv1lchQY
6) Basics of TOFD Part-2 ll Setup and configuration of "Time of flight diffraction"
technique: https://youtu.be/CehZ1JYTzXQ
7) UT echo signal patterns Part-1 ll Probe movements ll Porosity & cluster Po indication:
https://youtu.be/FqlRn9saP_0
8) UT echo signal patterns Part-2 ll Slag, LOF, LOP, crack indications:
https://youtu.be/5ATVyGg55vU
9) Scan patterns and contouring for curvatures in Ultrasonic testing:
https://youtu.be/Wo6V4x8FI38
10) Weld Defect Location calculation in Ultrasonic testing ll UT Level 2 & 3:
https://youtu.be/NBQ4SzoNLXI
11) Lack of side wall fusion Indication in UT ll LF echo pattern in Ultrasonic testing:
https://youtu.be/N07tG2kzzuU
12) Porosity Echo pattern in Ultrasonic testing ll Single, Large and cluster Porosity
indications in UT: https://youtu.be/KEsAJDCKyqg
13) High thickness Piping UT Probe selection ll Ultrasonic Testing:
https://youtu.be/PmxFqTN7eAA
14) Ultrasonic testing of wrought products ASTM E2375 ll UT procedure, classes for
acceptance ll Part-1: https://youtu.be/oESXHX9Nn3E
15) Ultrasonic testing of wrought products ASTM E2375 ll UT procedure, classes for
acceptance ll Part-2: https://youtu.be/b8jNF6ytNb8
16) UT of brazed and bonded joints ll Ultrasonic testing: https://youtu.be/g6zl3V1RTY0
17) Incomplete Penetration indication in UT ll Weld imperfection IP echo pattern ll UT
level 2: https://youtu.be/V0MpnOgID2s
18) Don't have calibration block for different materials? ll Velocity correction in
Ultrasonic testing: https://youtu.be/UGrsatyQKvQ
19) Identification of crack indication in Ultrasonic testing ll Crack signal pattern in UT:
https://youtu.be/hoBINEd0Ou8
20) 2 techniques for Lamination Ultrasonic testing ll Plate and pipe lamination UT ll Part-
1: https://youtu.be/fcJ2-s9zyio
21) 2 techniques for Lamination Ultrasonic testing ll Plate and pipe lamination UT ll Part-
2: https://youtu.be/fLc9Iga6Jks
22) ASTM SA 609- Ultrasonic testing ll FBH Block set ll Flat bottom hole calibration
reference blocks: https://youtu.be/JIzoNafgw2s
23) Probe resolution in Ultrasonic testing ll Lateral & Axial resolution ll UT level 2:
https://youtu.be/j_aFKj47ZPY
24) Weld UT Part-1 : PCN Ultrasonic testing 3.1 ll UT Level 2:
https://youtu.be/_scYEdUvLAk
25) Weld UT Part-2 : PCN Ultrasonic testing 3.1 ll UT Level 2:
https://youtu.be/4UT2soLtLbg
26) Practical - 2 Point calibration in UT machine ll How to find unknown material's
velocity in UT?: https://youtu.be/pDVoRL53q8M
27) Theory & Practical Part-1 UT Plate lamination ll Ultrasonic testing PCN Practical
Level 2: https://youtu.be/v3LMp8cjs7o
28) Theory & Practical Part-2 UT Plate lamination ll Ultrasonic testing PCN Practical
Level 2: https://youtu.be/ep7UG3DqEVo
29) Non relevant Indications in Ultrasonic testing Part-1 ll UT Training level 2 & Level 3:
https://youtu.be/wdCVPClFEtY
30) Non relevant Indications in Ultrasonic testing Part-2 ll UT Training level 2 & Level 3:
https://youtu.be/CrfEqp_zrzc
31) IIW Type 1 V1 block ll Calibration, resolution, sensitivity, Index point & True angle:
https://youtu.be/BHy4PBxn3PE
32) Ultrasonic testing discontinuity sizing techniques ll 20 dB drop and maximum
amplitude techniques: https://youtu.be/pYIeWOtlf64
33) Tandem technique in Ultrasonic testing ll How to do UT in thick specimen:
https://youtu.be/5xwmOBlEmhY
34) Ultrasonic pulse velocity test (UPV) ll UT of concrete and natural rocks ll NDT Level
3: https://youtu.be/w8MDteeJa5g
35) Ultrasonic immersion testing ll Immersion UT setup ll Bubbler & wheel type
transducers: https://youtu.be/v3juTSYdC2Q
36) Dead zone in UT Practical ll Comparison of Normal probe and TR probe ll Ultrasonic
testing: https://youtu.be/c_zx8gznG1M
37) UT practical of straight beam calibration using formulas ll Least count of UDF
instrument: https://youtu.be/aYckczT6BFU
38) Difficulties in High temperature Ultrasonic testing ll NDT level 3 in UT:
https://youtu.be/H4e6quTLlE8
39) DAC using notch block Part-1 ll How to draw DAC for piping weld UT? ll Distance
amplitude correction: https://youtu.be/Co9pcNOu2gE
40) DAC using notch block Part-2 ll How to draw DAC for piping weld UT? ll Distance
amplitude correction: https://youtu.be/YWHuDrZUSf0
41) Classification of sound waves ll Infrasonic, Audible & Ultrasonic frequencies ll UT
Level 2 & 3: https://youtu.be/f9wzSCSDd1U
42) Difficulty in Ultrasonic testing of Austenitic stainless steel ll Transmission losses in
UT: https://youtu.be/aIbbSOMrG6E
43) Ultrasonic testing False indications & Solution ll Misinterpretation due to backing bar
of weld: https://youtu.be/DzjhpucGAvU
44) Part-1 Ultrasonic testing Equipment ll Cathode ray tube (CRT) screen and circuits of
machine: https://youtu.be/fpNdq3Md0Ps
45) Part-2 Ultrasonic testing Equipment ll Pulsar circuit of UDF instrument ll UT
machine working: https://youtu.be/ogoDH7eqI4U
46) Part-3 Ultrasonic testing Equipment ll Receiver of UDF ll Reject, Rectifier and
Amplifier circuits: https://youtu.be/_uR88s72Dos
47) Part-4 Ultrasonic testing Equipment ll Sweep circuit of UDF ll Delay and Range
control of UT machine: https://youtu.be/Isco1bh99j4
48) Part-5 Ultrasonic testing Equipment ll Gate circuit of UDF ll Gate start, End & Level
in UT machine: https://youtu.be/61_kag4lU2w
49) Ultrasonic thickness gauge ll Working and principle ll How to use UTM DTM
machine?: https://youtu.be/Et9OXuHwtSQ
50) How Ultrasonic probe works? ll Construction of UT Transducer:
https://youtu.be/Byy6rxOmqok
51) Phased array ultrasonic testing ll How PAUT works? ll Difference between
conventional UT and PAUT: https://youtu.be/71N2XPb0myw
52) Evaluation of UT indications explained ll Which type of echo you will get of an
indication ll Part-1: https://youtu.be/GRxWNavoR7A
53) Evaluation of UT indications explained ll Which type of echo you will get of an
indication ll Part-2: https://youtu.be/s4kv15XeY1Y
54) AWS D1.1 Ultrasonic testing procedure Part-1 ll Scanning pattern & Probe angle
selection ll UT L-3: https://youtu.be/wM6SnOiAF3c
55) AWS D1.1 Ultrasonic testing procedure Part-2 ll Calibration & accepance criteria ll
UT L-3: https://youtu.be/wFo9L9-zApk
56) AWS D1.1 Ultrasonic testing procedure Part-3 ll Question & Answers ll UT Level 2
& 3: https://youtu.be/mB9D1iRsLes
57) Long range ultrasonic testing (LRUT) ll Guided wave UT:
https://youtu.be/gOK3JvWv8q4
58) UT Amplitude control linearity ll Ultrasonic testing ll 6dB amplitude:
https://youtu.be/vU-6OdibOc8
59) Ultrasonic pitch catch technique ll Direct and Indirect pitch catch testing:
https://youtu.be/2jNwMEQuhhw
60) Vertical linearity in ultrasonic testing ll ASME Sec V, Article-4, Mandatory appendix-
I: https://youtu.be/cs30VTtujPM
61) UT Effect of Discontinuity Orientation & Geometry on Signal Amplitude ll Ultrasonic
testing: https://youtu.be/0Wu-Z_tuWyM
62) Ultrasonic testing of railroad parts ll Railway tracks, Axels, Wheels UT ll Rail
Ultrasonic testing: https://youtu.be/6Dz9ZHiFYM0
63) 6 dB drop technique UT ll Ultrasonic testing sizing of indications ll NDT Level 2:
https://youtu.be/pGYOlnGr0B8
64) Through transmission Ultrasonic testing ll Pulse echo contact testing ll UT level 2
course: https://youtu.be/Qxk4YhTUyxo
65) Ultrasonic testing Couplant working principle ll Contact and Immersion testing
couplants: https://youtu.be/lWLLI4h9xH8
66) Indication vs discontinuity vs flaw vs defect ll All terms explained:
https://youtu.be/SU5WkhT6Vs4
67) Acoustic impedance Ultrasonic testing ll Ultrasound Physics ll UT Principle Level 2:
https://youtu.be/CywuBtMjPfw
68) UT Acceptance Criteria ll Ultrasonic Testing Weld Criteria as per ASME Sec VIII,
Div-1 ll UT Level 2: https://youtu.be/H26ZpHrEBVY
69) Forging Defects in Hindi ll Which discontinuities can be found in forging? ll Types of
forging: https://youtu.be/qo7D2TKelRs
70) IRIS NDT testing ll Internal Rotary Inspection System ll IRIS UT Technique
Advantages & Limitations: https://youtu.be/B2VjorJ1nGE
71) Different Ingot Discontinuities ll What is Ingot? ll Pipe, Scab, Void, Non metallic
inclusion, Crack: https://youtu.be/QsRxo1_-2wc
72) 2 techniques for checking resolution of Ultrasonic testing system ll UT probe
resolution power: https://youtu.be/F5WwqQsjzC8
73) Casting defects in Hindi ll Casting discontinuities causes and remedies ll NDT &
Quality: https://youtu.be/grRDbFqjq0s
74) Difference between Codes, standard and specifications ll How to use codes (Hindi
Video): https://youtu.be/M0rWzLwi6_I
75) Physical Principles of Ultrasonic testing ll Velocity, Frequency and Wavelength in UT
ll UT Level 2: https://youtu.be/5X5oWNSNeFc
76) Frequency selection Ultrasonic testing ll Can we do UT on Austenitic Stainless steel?:
https://youtu.be/MwOjJJPKOjI
77) Welding defects in hindi ll Porosity, cracks, spatter, overlap, LF, Slag, Undercut, BT:
https://youtu.be/_yCqRPBBtHo
78) Near zone in ultrasonic testing ll Beam spread in ultrasonic testing ll Far zone:
https://youtu.be/y1rsn2EJrCg
79) UT Shear wave calculations in Hindi ll Ultrasonic testing Level 2 calculations ll NDT
& Quality: https://youtu.be/ZIlkxm1mPvQ
80) UT acronym & parameters (In Hindi) II NDT level 2 UT Basics:
https://youtu.be/V9evjbYzadk