SSS2 OBJECTIVE TEST
1. In isomeric projection, the square faces of the cube are seen as
A. Squares
B. Rectangles
C. Rhombus
D. Any of the above
2. Isometric view of a rectangle is a
A. Rhombus
B. Square
C. Rectangle
D. Parallelogram
3. Isomeric view of a circle is a(an)
A. Circle
B. Ellipse
C. Parabola
D. Line
4. In oblique projection, the object is assumed to be placed with one face ..............
A. Parallel to plane of projection
B. Parallel to adjacent edge
C. Perpendicular to plane projection
D. Perpendicular to adjacent edge
5. What is the shape of a surface if a right circular cone is cut by a plane perpendicular to the axis?
A. Circle
B. Ellipse
C. Parabola
D. Hyperbola
6. Which is a practical application of involutes circle?
A. Gear tooth profile
B. Spring of clock
C. Screw thread
D. Rader antenna
7. What is the term for the locus of a point lying on the circumference of the circle which rolls on a straight line?
A. Cycloid
B. Hypocycloid
C. Epicycloids
D. Circle
8. In an oblique drawing, all of the following angles are commonly used for drawing the depth axis except
A. 30 degree
B. 45 degree
C. 60 degree
D. 90 degree
9. How many sides has a regular nonagon?
A. Twelve
B. Eleven
C. Ten
D. Nine
10. Which of the following is not a type of triangle?
A. Equilateral
B. Isosceles
C. Rhombus
D. Scalene
11. When an object is truncated by a cutting plane, the lower portion is called a(an)
A. Kite
B. Prism
C. Frustum
D. Pyramid
12. An ellipse has .......axes
A. Eight
B. Six
C. Four
D. Two
13. The part of a circle bounded with an arc and a chord is(an) ..........
A. Arc
B. Quadrant
C. Sector
D. Segment
14. Which line is thin and light?
A. Visible lines
B. Centre lines
C. Construction lines
D. All of the above
15. Which of the following is not a type of quadrilateral?
A. Trapezoid
B. Trapezium
C. Rhombus
D. Scalene
16. The locus of a point in a circle which rolls inside a larger circle is called
A. Cycloid
B. Hypocycloid
C. Parabola
D. Hyperbola
17. The locus which uses two concentric circle as a method for its construction is a(an)
A. Cycloid
B. Hyperbola
C. Parabola
D. Ellipse
18. Which of the following is constructed using the principle of involute?
A. Gear
B. Headlamp
C. Spring
D. Staircase
19. Which of the following information is not included in a title block?
A. Name of drawer
B. Title of drawing
C. Drawing scale
D. Time limit
20. These are importance of technical drawing except
A. It develop our skill
B. It help in interpreting drawing
C. Means of communication
D. It gives us information about events
21. Drawing materials and instruments should be .........
A. Handle with care
B. Handle roughly
C. Kept in the roof
D. Played with always
22. is used for angular measurements
A. Pair of compass
B. Set square
C. Tee-square
D. Protractor
23. ...........is the process of putting down information
on a drawing by means of letter's, words and numbers
A. Information
B. Title block
C. Lettering
D. Dimension
24. .......... Is drawn at the bottom right hand corner of the drawing paper
A. Information
B. Title block
C. Lettering
D. Boarder line
25. ............are used to draw vertical lines by placing one one side of the triangle containing the right angle against
the upper edge of the tee-square
A. Drawing board
B. Set square
C. Tee square
D. Drawing paper
26. A line drawn around the inside edge of the drawing paper is called .........
A. Straight line
B. Title block
C. Boarder line
D. Lettering line
27. All the following are pencil types except
A. HB
B. 2B
C. 2A
D. 6B
28. .........is used to draw arcs and circles
A. Pair of compass
B. Set square
C. Tee square
D. Divider
29. 100mm2 is the same as
A. 1cm2
B. 10cm2
C. 1,000cm2
D. 10,000cm2
30. Which of the following instruments can be used in conjunction with the tee square to draw inclined lines?
A. French curve
B. Meter Rule
C. Pair of dividers
D. Set square
