Sheet 1 of 2
Customer : Air Liquide Project : 9042 - Chile Project Valve Tag # : FV 1535
Control Valve Specification PO # : ALEI/51-9042/1113/BS/8 Proj Num : Page # : 1
Prepared By : Serial # : 819924.001 Quote ID : P&ID :
Flowserve Corporation Rev/By : 5.0/SKarthikeyan Alternate : Line :
Springville Utah Application : Date / Ver : 2012-03-05 /10.6270.1
1 Pipe Size, Up/Down 8.000 / 8.000 51 Act. Type/Matl VL Cylinder / Aluminum
2 Pipe Sch, Up/Down 40 / 40 52 Act. Size/Fab 100 / STD
3 Allow Noise/Add Attn/Type 85 / 0 / 53 Stroke/Spring 3.00 / Heavy Duty
Process Data For Control Valve Selection
4 Process Fluid Air 54 Fail/Air-To Close / Open
Actuator
5 Design Press./Temp. 1.01 / 5.33 bar (a) / 0.00 / -5.70 °C 55 Volume Tank
6 Cond 1 Cond 2 Cond 3 Cond 4 56 Tubing Size/Mtl 1/4" / 316 SS
7 Temperature (°C) -5.700 -20.000 57 Fitting Mfg/Mtl Swagelok / 316 SS
8 Inlet Press (bar (a)) 5.328 4.786 58 Handwheel
9 Outlet Press (bar (a)) 1.080 1.010 59 Actuator O-Rings Low Temp Nitrile
10 Liq Flow Rate (m³/h) 0 0 60
11 Gas Flow Rate (Nm³/h) 11300.000 6350.000 61
12 Viscosity (cP) 0.000 0.000 62 Model Logix 3000 Series / MD
13 Vapor Press (bar (a)) 0.000 0.000 63 Model # 3200MD-14-D6-M-04-40-0G-00
14 SG-MW 28.900 28.900 64 Diagnostic Standard
15 Max Shutoff / Shutoff Class 7.000 bar / AL Class III.2 65 Comm/Signal HART / 4 - 20 mA
Positioner
16 Available Air Supply 6.000 bar (g) 66 Housing/Conn Aluminum, White / M20
17 Valve Function Throttling 67 Piezo Temperature -40F to 185F (-40C to 85C)
18 Cond 1 Cond 2 Cond 3 Cond 4 68 Shaft Linear-D Shaft
19 Flow Coeff. (Cv) 157.721 95.796 69 Action 4-Way
Calculated Data
20 Est Stroke (Percent) 67.000 35.000 70 Feedback None
21 Pressure Drop (bar ) 4.248 3.776 71 Gauges 2 SS-Brass PSI/BAR/KPA
22 Choke Drop (bar ) 3.730 3.350 72 Pos Tag/Mounting /
23 Noise [IEC] (dBA) 103.000 101.000 73 Model
24 Valve Vel (mach#) 0.462 0.274 74
25 Pipe Vel (mach#) 0.265 75
26 Valve Model / Body Type Mark Six / Globe / Standard Pos Ind Sw
76
27 Size/Pressure Rating/Type 6.00 / CL 150 77
28 Trim # - Cv / Characteristic 3.00 Cv:192 / Linear 78
29 Flow Direction Flow Over 79
30 Body Matl / Bonnet Matl 304L SS / Same As Body Mtl 80
31 Body Extn. / Material 36" Cryo. Ext. / Same As Body Mtl 81
32 End Conn/Sch/Face to Face Butt Weld / 10S / ISA S75.08.05 82 Model/Qty
33 Flange Finish 83 Cv-Kv/De-en
Solenoid
34 Bonnet Type Standard / 84 Volt/Watt
35 Trim Type Vented Plug 85 Body/Housing Mtl
Valve Body Assembly
36 Plug Matl / Facing 316LSS / 86 Body/Elect Conn
37 Stem Matl / Facing 316 SS / 87 Port Size/Mtg
38 Seat Ring Matl / Facing 316LSS / 88 Tag/Reset-Override
39 Plug Seal/Soft Seat Matl. PTFE / 89 Air Filter/Mnting /
40 Retainer Matl/Sleeve Matl 90 Filter-Reg/Mnting Valtek / Nipple Mtd
41 Guides Upper/Lower 304LSS & GL PTFE/304LSS & GL PTFE 91 Flow Booster /
42 Packing Matl / Style / Vac / Fire PTFE V-Ring/Single// 92 Booster Config
43 Packing - Live-Loaded 93 Quick Exhaust /
Others
44 Bonnet Port Type 94 SupTube/Jctn Box /
45 Bellows Type 95 Lockup
46 Bellows Material 96 Plate ID
47 Body Bolting/Bonnet Flange Matl B8-8 (304 SS) / 316 SS 97 Plate Type
48 Gaskets PCTFE 98 Packaging Standard
49 Gland Flange Material Stainless Steel 99 Pwr. Sup.
50 Gland Flange Bolting Stainless Steel 00 Wiring Conn. Type
01 Certification / Approval Type / / 01 Rad. Exm
02 Class or Gas Group No Cert Req 02 Drawings Type II w/ Bill of Materials
Customer Spec
03 Division or Zone No Cert Req 03 Assem Hydro As per E-GS-5-4-4-A
Special Req
04 Group No Cert Req 04 Seat Leak / Cryo Test Air Liquide CS.440.03
05 Ingress / Temperature IP 65 / 05 PMI Test
06 NACE NA 06 Cert of Conf.
07 SIL Vlv-Act / Pos NA / NA 07 Clean/Bld/Doc as per W-GS-4-0-1-B / Final Insp
08 Nuclear NA 08 CMTR Body & Bonnet
09 Special Paint/Test /
10 Diag Test/FM /
11 Cust. Insp/Witn. Yes / Yes
12
Line #: Remarks
CE 37 316LSS
C 38 316LSS
C 41 304LSS & GL PTFE
C 41 304LSS & GL PTFE
C 103 As per E-GS-5-4-4-A
DB rev: 1169 : 2012-03-02 : ID = XMathews_SKVW7786_118 Quantity: 1
