Scribd
Upload
70 views

DTC Check - Clear

Uploaded by

powertrainmotors1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views

DTC Check - Clear

Uploaded by

powertrainmotors1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Print-Toyota Service Information 11/3/17, 9(23 pm

Print Exit

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS ANTI-LOCK BRAKE SYSTEM DTC CHECK / CLEAR

DTC CHECK/CLEAR (When Using GTS)

a. Check the DTC.


i. Turn the ignition switch off.

ii. Connect the GTS to the DLC3.

iii. Turn the ignition switch to ON.

iv. Turn the GTS on.

v. Read the DTCs following the prompts on the GTS screen. Enter the following menus: Chassis /
ABS/VSC/TRC / Trouble Codes.
Chassis > ABS/VSC/TRC > Trouble Codes

Execute

vi. Check the details of the DTCs.


Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE
SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

b. Clear the DTC.


i. Turn the ignition switch off.

ii. Connect the GTS to the DLC3.

iii. Turn the ignition switch to ON.

iv. Turn the GTS on.

v. Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble
Codes.
Chassis > ABS/VSC/TRC > Clear DTCs

Execute

vi. Clear the DTCs by following the prompts on the GTS.


HINT:
Refer to the GTS operator's manual for further details.

DTC CHECK/CLEAR (When Using SST Check Wire)

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000L254.html?PUB_TYPE=RM&MODE=1 Page 1 of 4
Print-Toyota Service Information 11/3/17, 9(23 pm

a.

*a Front view of DLC3

Check the DTC.


i. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST
09843-18040

ii. Turn the ignition switch to ON.

iii. Observe the blinking pattern of the ABS warning light in order to identify the DTC.
HINT:
If no code appears, inspect the TC and CG terminal circuit, and ABS warning light circuit.

Trouble Area See procedure


TC and CG terminal circuit ( )
ABS warning light circuit (Remains on) ( )
ABS warning light circuit (Does not come on) ( )

iv. Count the number of blinks of the ABS warning light.


HINT:
· When the system is operating correctly, each light will blink continuously in a pattern of 0.25
seconds on, and then 0.25 seconds off.
· When one DTC is output, each light will output the same code at 4 second intervals (for
example, code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash).
· When 2 or more DTCs are output, each light will output a different code at 2.5 second
intervals, and when all codes have been output, there will be a 4 second pause and the
sequence will repeat.
· When multiple codes are stored, they are output in order starting with the lowest DTC number.

v. Check the details of the DTCs.


ABS DTC
Warning Light Display GTS Display
11 C146E
12 C146F
13 C146C
14 C146D
21 C1468
22 C1469
23 C146A
24 C146B
C1401
31

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-j…manual/repair/contents/RM100000000L254.html?PUB_TYPE=RM&MODE=1 Page 2 of 4
Print-Toyota Service Information 11/3/17, 9(23 pm

C1405
C1402
32
C1406
C1403
33
C1407
C1404
34
C1408
35 C1413
36 C1414
37 C1337

38 C1415
39 C1416
C1241
41
C1417
43*1 C1243
44*1 C1418
45*1 C1245
49 C1425
C1427
51
C1428
59 C1203
68*2 C1268
94 U0073
A1*3 U0114

*1: for 4WD and Pre-Runner


*2: for 4WD
*3: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.

vi. After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.
HINT:
If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.

b. Clear the DTC.


i.

*a Front view of DLC3

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000L254.html?PUB_TYPE=RM&MODE=1 Page 3 of 4
Print-Toyota Service Information 11/3/17, 9(23 pm

ii. Turn the ignition switch to ON.

iii. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

iv. Check that the warning light indicates a normal system code.

v. Remove SST from the terminals of the DLC3.


HINT:
The DTCs cannot be cleared by disconnecting the battery terminal or the IG1 NO. 3 fuse.

END OF DTC CHECK/CLEAR

a. Turn the ignition switch to ON.

b. Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch
to ON.

© 2012 TOYOTA MOTOR CORPORATION. All Rights Reserved.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…manual/repair/contents/RM100000000L254.html?PUB_TYPE=RM&MODE=1 Page 4 of 4

You might also like