Self Diagnosis

Supported model

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

REPAIR MANUAL
RB1FS Chassis
Segment: FS-L

MODEL COMMANDER DESTINATION

XBR-55X900A RM-YD087/RMF-YD001 US/CND

XBR-55X900A

Version Date Subject

1.0 03/20/2013 Original Manual Release Date.
2.0 07/03/2013 Updated Section 3 - Repair Information. Reissue entire manual.
3.0 10/25/2013 Updated Section 4 - Exploded View/Part Number Information. Replaced pages 22 - 28.

LCD Digital Color TV

9-888-524-03
TABLE OF CONTENTS

Cautions and Warnings....................................................................................ii Section 3 - Repair Information.......................................................................14

Section 1 - Specifications and Layouts..........................................................1 Repairing the TV...........................................................................................14
Specifications.................................................................................................1 Removing the Table-Top Stand and Cover Under................................................14
Checking the Accesories........................................................................................1 Removing the Rear Cover....................................................................................14

Board Layout..................................................................................................2 Replacing the Main Board............................................................................15

XBR-55X900A........................................................................................................2 Replacing the Power Supply Board..............................................................18
Wire Dressing.................................................................................................3 Replacing the CX Board...............................................................................18
XBR-55X900A........................................................................................................3 Replacing the Switch Unit............................................................................20
Smart Core Block...................................................................................................3 Removing the Woofer Speaker....................................................................20
Section 2 - Troubleshooting............................................................................4 Removing the WLAN Module and HW Board..............................................20
Diagnosing the Error......................................................................................4 Removing the Side Speakers.......................................................................21
Viewing the Self Check Diagnosis History..............................................................4
Removing the Smart Core Block..................................................................22
Triage Chart....................................................................................................5
Removing the TS Board...............................................................................22
Flowcharts and Diagrams...............................................................................6
Section 4 - Exploded View/Part Number Information..................................23
Overall Block Diagram / BAFS...............................................................................6
XBR-55X900A..............................................................................................23
Overall Block Diagram / BAF2S.............................................................................7
Smart Core Block.................................................................................................27
Power and Control Block Diagram.........................................................................8
Connectors...................................................................................................28
No Power Flowchart...............................................................................................9
Standby LED Blinking Flowchart..........................................................................10 Screws..........................................................................................................29
No Video Flowchart.............................................................................................. 11 Section 5 - Accesories/Part Number Information........................................30
Video Distorsion Flowchart...................................................................................12 Accessories and Packaging.........................................................................30
No 3D Viewing......................................................................................................13 Miscellaneous...............................................................................................30
Optional Accessories....................................................................................30
Remote Commander....................................................................................30
Appendix A: Encryption Key Components................................................ A-1

XBR-55X900A i
CAUTIONS AND WARNINGS

CAUTION!! ATTENTION!!
These servicing instructions are for use by qualified service personnel only. Ces instructions de service sont à l’usage du personnel de service qualifié
To reduce the risk of electric shock, do not perform any servicing other than seulement. Pour prévenir le risque de choc électrique, ne pas faire l’entretien
that contained in the operating instructions unless you are qualified to do so. autre que celui contenu dans le Mode d’emploi à moins que vous soyez
qualifié faire ainsi.

WARNING!!
ALERTE!!
An isolation transformer should be used during any service to avoid possible
shock hazard, in case of live chassis. Afin d’eviter tout risque d’electrocution provenant d’un chássis sous tension,
un transformateur d’isolement doit etre utilisé lors de tout dépannage.

! SAFETY-RELATED COMPONENT WARNING!!

! ATTENTION AUX COMPOSANTS
There are critical components used in LCD color TVs that are important for
safety. These components are identified with shading and ! mark on the
RELATIFS A LA SECURITE!!
schematic diagrams and the parts list. It is essential that these critical parts Les composants identifies par une trame et par une marque ! sur les
be replaced only with the part number specified in the parts list to prevent schemas de principe, les vues explosees et les listes de pieces sont d’une
electric shock, fire or other hazard. importance critique pour la securite du fonctionnement. Ne les remplacer
que par des composants Sony dont le numero de piece est indique dans le
present manuel ou dans des supplements publies par Sony. Les reglages
NOTE: Do not modify the original design without obtaining written permission
de circuit dont l’importance est critique pour la securite du fonctionnement
from the manufacturer or you will void the original parts and labor warranty.
sont identifies dans le present manuel. Suivre ces procedures lors de
chaque remplacement de composants critiques, ou lorsqu’un mauvais
ATTENTION!! fonctionnement suspecte.
For safety reasons, component level repair of the Power Supply Boards
and/or the Inverter Boards is prohibited. ATTENTION!!
Pour des raisons de sécurité, Interdire de réparer ou remplacer les
composantes dans les blocs d’alimentation et/ou sur les modules d’inverseur.

XBR-55X900A ii
 CAUTIONS AND WARNINGS

SAFETY CHECK-OUT 3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so
After correcting the original service problem, perform the following safety analog meters must have an accurate low voltage scale. Nearly all
checks before releasing the set to the customer: battery-operated digital multimeters that have a 2 VAC range are
suitable. (see Figure A)
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes To Exposed Metal
and bridges. Parts on Set

2. Check the interboard wiring to ensure that no wires are “pinched” or

touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps and
mounting hardware have been replaced. Be absolutely certain that AC
0.15 µF Voltmeter
you have replaced all the insulators. (0.75V)
4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of Earth Ground
deterioration. Point them out to the customer and recommend their
Figure A. Use an AC voltmeter to check AC leakage.
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer. HOW TO FIND A GOOD EARTH GROUND
7. Check the antenna terminals, metal trim, “metallized” knobs, screws The cover-plate retaining screw on most AC outlet boxes is at earth ground.
and all other exposed metal parts for AC leakage. Check leakage Verify the AC outlet box retaining screw ground by connecting a 60W to
as described in “Leakage Test”. 100W incandescent (not a neon or fluorescent lamp) between the hot side of
the receptacle and the retaining screw. Try both slots, if necessary, to locate
the hot side on the line; the lamp should light at normal brilliance if the screw
LEAKAGE TEST is at ground potential. (see Figure B)

The AC leakage from any exposed metal part to earth ground and from all Trouble Light
exposed metal parts to any exposed metal part having a return to chassis, AC Outlet Box
must not exceed 0.5 mA (500 microamperes). Leakage current can be
measured by any one of three methods.
1. A commercial leakage tester.
Follow the manufacturers’ instructions provided with the tester.
2. A battery-operated AC milliammeter.
Figure B. Checking for earth ground.

XBR-55X900A iii
SECTION 1 - SPECIFICATIONS AND LAYOUTS

SPECIFICATIONS
System Model name XBR-55X900A
Television system NTSC: American TV standard Power and others
ATSC (8VSB terrestrial): ATSC compliant 8VSB
Power requirement 1 1 0 -2 4 0 V A C , 5 0 /6 0 H z ( USA/Canada 120 V AC, 60 Hz)
QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality)
Power in us e 268 W
Channel coverage Analog terrestrial: 2 - 69 / Digital terrestrial: 2 - 69 consumption
Analog Cable: 1 - 135 / Digital Cable: 1 - 135 in standby 0.20 W
Panel system LCD (Liquid Crystal Display) Panel Screen size* 54.6 inches
(inches measured diagonally) (55 class)
Speaker output 12,5 W + 12,5 W + 20 W + 20 W
Display resolution 3 , 8 4 0 d ots ( horiz onta l) × 2 , 1 6 0 line s ( ve rtic a l)
Input/Output jacks
Dimensions* with stand (mm) 1,463 × 778 × 405
CABLE/ANTENNA 75-ohm external terminal for RF inputs (inches) 57 5 /8 × 30 3/4 × 16
VIDEO IN 1 Video / Audio input (phono jacks)
without stand (mm) 1,463 × 749 × 100
COMPONENT IN YPB P R (Component Video): 1080p (60 Hz), 1080i (60 Hz), 720p (60 Hz), 480p, 480i (inches) 57 5/ 8 × 291/2 × 4
Audio input (phono jacks)
wall-mount hole pattern (mm) 300 × 300
VIDEO IN 2 Video input (common phono pin with Y input)
(inches) 11 7/8 × 11 7/8
HDMI IN 1/2/3/4 Video (2D): 4096 × 2160p (24 Hz), 3840 × 2160p (24, 25, 30 Hz), 1080p (30, 60 Hz), wall-mount screw size M6 (8-12 mm)
(Support 4K resolution) 1080/24p, 1080i (60 Hz), 720p (30, 60 Hz), 720/24p, 480p, 480i,
PC Formats Mass * with stand ( k g ) /( lb) 34, 5 / 76, 0
Video (3D): without stand ( k g ) /( lb) 33, 1 / 73, 0
Frame Packing 1080p (30 Hz), 1080/24p, 1080i (60 Hz), 720p (30, 60 Hz), 720/24p Optional accesories Connecting Cables
Side-by-Side 1080p (60 Hz), 1080/24p, 1080i (60 Hz), 720p (60 Hz) Support Belt Kit
Over-Under 1080p (30, 60 Hz), 1080/24p, 1080i (60 Hz), 720p (60 Hz) Camera and Microphone Unit: CMU-BR200/CMU-BR100
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital USB Wireless LAN Adapter: UWA-BR100
ARC (Audio Return Channel) (HDMI IN 1 only) Passive 3D Glasses: TDG-500P
MHL Video (2D): 1080p (30 Hz), 1080/24p, 1080i (60 Hz), 720p (30, 60 Hz), 720/24p, 480p, 480i
(common with HDMI IN 2) Video (3D):
Side-by-Side 1080/24p, 1080i (60 Hz), 720p (60 Hz)
Over-Under 1080p (30 Hz), 1080/24p, 1080i (60 Hz), 720p (60 Hz) SimulView™ Passive Glasses: TDG-SV5P
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
AUDIO OUT/Headphones Stereo mini jack
DIGITAL AUDIO OUT Digital optical jack (Two channel linear PCM, Dolby Digital)
(OPTICAL)
Operating temperature 32ºF - 104ºF (0ºC - 40ºC)
L AN 10BASE-T/100BASE-TX connector (Connection speed may differ depending on the network
environment. 10BASE-T/100BASE-TX communication rate and communication quality * Screen size, dimensions and mass are approximate values.
are not guaranteed for this TV)
• Optional accessories availability depends on countries/region/TV model/stock.
USB/DLNA Refer to the i-Manual for supported formats • Design and specifications are subject to change without notice.
REMOTE RS232C, Serial Control mini jack; IR IN mini jack
These jacks are for receiving the external control signal
CHECKING THE ACCESORIES
Remote Control (1) *1 *1 Please refer to the model name printed on the
One-touch Remote Control (1) *1 remote control.
*2 Assembling the Table-Top Stand is required.
Size AAA Batteries (4) Refer to the supplied Table-Top Stand leaflet to
Under Cover (1) assemble the Table-Top Stand.
Cable Clamper (1)
Table-Top Stand (1) * 2
Fixing Screws for Table-Top Stand
(M5 × 12) (4)
Passive 3D Glasses (4)
Operating Instructions and other documents

XBR-55X900A
 SECTION 1 - SPECIFICATIONS AND LAYOUTS

BOARD LAYOUT

XBR-55X900A
TS BOARD

POWER BOARD POWER BOARD

(NETWORK) (NETWORK)
POWER BOARD
(E- LD) MAIN BOARD
(BAFS/BAF2S)

POWER POWER
SUPPLY SUPPLY
WLAN MODULE ASSEMBLY BOARD BOARD
(G7) (G6)

WLAN CX/CX2 BOARD*

Module
SWITCH UNIT
TCON

HW Board
*CX/CX2 only included in models with
BAFS Board (Serial No. 1800001 - 6010000).
SMART CORE BLOCK Bluetooth
Module
HIF Board

HSF - LM Board

XBR-55X900A
 SECTION 1 - SPECIFICATIONS AND LAYOUTS

WIRE DRESSING

XBR-55X900A SMART CORE BLOCK

*CX/CX2 Board wire only included in models

with BAFS Board (Serial No. 1800001 -
6010000).

XBR-55X900A
SECTION 2 - TROUBLESHOOTING Self Diagnosis
Supported model

DIAGNOSING THE ERROR StandBy LED

Blink Count
Before servicing the Television: Diagnosis
Date and Time Display*

Item
1. Verify the TV has the symptom the customer indicated.
2. Check to see if the latest Software is installed. SELF CHECK
a. If not, install the latest version.
000 RESERVED --------------------- --------------------- --------------------- 00
3. Determine the replacement part required. 000 RESERVED --------------------- --------------------- --------------------- 00
002 MAIN_POWE --------------------- --------------------- --------------------- 00
003 DC_ALERT --------------------- --------------------- --------------------- 00
VIEWING THE SELF CHECK DIAGNOSIS HISTORY 003 AUD_PROT --------------------- --------------------- --------------------- 00
003 HDMI_EQ --------------------- --------------------- --------------------- 00
When an error is detected, the Self Check screen records the number of 003 TU_DEMOD --------------------- --------------------- --------------------- 00
times the error occurred. This is helpful in confirming past occurrences of an 004 VLED --------------------- --------------------- --------------------- 00
error and for determining if an error is intermittent when the customer is not 004 LD_ERR --------------------- --------------------- --------------------- 00
005 HFR_ERR --------------------- --------------------- --------------------- 00
sure what is causing the television to shut down. If the screen displays a “0”, 005 TCON_ERR 120123132522 120123113645 --------------------- 02 Error Count
no error has occurred. 005 P_ID-ERR --------------------- --------------------- --------------------- 00
(00-99)

006 BACKLITE --------------------- --------------------- --------------------- 00

1. Press POWER to turn on the TV and then turn it off again. 007 TEMP_ERR --------------------- --------------------- --------------------- 00
007 FAN_ERR --------------------- --------------------- --------------------- 00
2. Press the following buttons on the Remote Commander within 1
010 EMITTER --------------------- --------------------- --------------------- 00
second of each other: 101 VPC_WDT --------------------- --------------------- --------------------- 00
102 MEPS_WDT --------------------- --------------------- --------------------- 00
DISPLAY Channel 5 Volume - POWER 103 HOST_WDT --------------------- --------------------- --------------------- 00
104 STBY_WDT --------------------- --------------------- --------------------- 00

NOTE: This differs from accessing Service Adjustments Mode (Volume +). 00345 000333 06789

Panel operation time by hour (MAX:65535)

Boot count (MAX:65535)
Total operation time by hour (MAX:65535)

*Format of Error History = YYMMDDhhmmss example 120123132522= Jan 23, 2012 13:25:22 (1:25:22PM)
NOTE: date and time must be set for this to work

SAMPLE SELF CHECK DIAGNOSIS PAGE

XBR-55X900A 4
 SECTION 2 - TROUBLESHOOTING

TRIAGE CHART
Use this general Triage Chart to determine what may possibly be causing the error before going out to the customers location.

1. Confirm the symptom from the customer. Red Dot: (Primary) Most likely defective part.
2. Select that symptom from the chart.
Blue Triangle: (Secondary) Possible defective part.
3. Bring the primary component listed for that symptom.
4. Follow the associated flowcharts in the Training Manual to isolate the board.
5. Chart Color Code.

Protection Modes LAN Power Video Audio

Board Whole Isolated
No No
2X 3X 4X 5X 6X 7X 8X Dead set Screen Area No Audio
WIFI Video
Distortion Distortion

MAIN BOARD  * ▲ ▲ ▲ ▲  
POWER SUPPLY   
LCD Panel  
TCON   ▲ ▲
SERVICE BULLETIN  ▲
SOFWARE UPDATE  
WLAN 
*NOTE: REFER TO LCD PANELS SERVICE MANUAL IN * Immediate Shutdown After Power ON & 7X
REFERENCE LIBRARY DATABASE FOR CORRECT
REPLACEMENT PARTS BASED ON SERIAL NUMBER.

To access the most recent version of the Triage documents for the models listed in this manual, login into the Sony Authorized Servicer Portal at
http://www.sony.com/asp.

XBR-55X900A 5
 SECTION 2 - TROUBLESHOOTING

FLOWCHARTS AND DIAGRAMS

OVERALL BLOCK DIAGRAM / BAFS

MAIN BOARD
L
SUB-
WOOFER
AMP R

L
AMP

USB2.0
RF TUNER

VIDEO 1 CVBS
OPTICAL
VIDEO 2 CVBS/COMP IC9001 AUDIO OUT
HP/LINE OUT

IC9000
A/V
HDMI 1 DECODER
HDMI VIDEO
HDMI 2 SWITCH PROCESS
EQ
HDMI 3

HDMI4 LVDS
CX/CX2
HFR
ETHERNET LVDS TCON

USB2.0 USB HUB

LCD PANEL
USB3.0
BAFS

SMART CORE LED DRIVE

LD
IR RX SWITCH TS
OPTICAL UNIT
BLUETOOTH WIFI
SENSE
HUS
HSF HIF HW

AC IN POWER SUPPLY POWER SUPPLY

G7 G6

XBR-55X900A 6
 SECTION 2 - TROUBLESHOOTING

OVERALL BLOCK DIAGRAM / BAF2S

MAIN BOARD
L
SUB-
WOOFER
AMP R

L
AMP

USB2.0
RF TUNER

VIDEO 1 CVBS
OPTICAL
VIDEO 2 CVBS/COMP IC9001 AUDIO OUT
HP/LINE OUT

IC9000
A/V
HDMI 1 DECODER
HDMI VIDEO
HDMI 2 SWITCH PROCESS
EQ
HDMI 3

HDMI 4 HDMI LVDS

EQ
HFR
ETHERNET LVDS TCON

USB2.0 USB HUB

LCD PANEL
USB3.0
BAF2S

SMART CORE LED DRIVE

LD
IR RX SWITCH TS
OPTICAL UNIT
BLUETOOTH WIFI
SENSE
HUS
HSF HIF HW

AC IN POWER SUPPLY POWER SUPPLY

G7 G6

XBR-55X900A 7
 SECTION 2 - TROUBLESHOOTING

POWER AND CONTROL BLOCK DIAGRAM

CN6001 CN6402 CN6602 MAIN POWER AND

AC IN (N) 1 1 BL_ERR 1 CONVERTER CN6601
AC IN (L) 3 2 LD_ERR 2 1~4 VLED_VCC

3 DIGITAL_STBY 3 7~9 VLED_GND

E-LD
4 BL_ON 4 6 SENSE GND
BOARD
5 GND 5 11 LD_ERR

6 REG 12V 6 12 GL_CTRL

14 REG_12V
CN6102 CN6101
1 AC-N 1
3 AC-L 3

PFC, PRI_VCC AND G6

STANDBY POWER SUPPLY
MAIN BOARD
CN9101
CN6401 POWER_ON 1
28 POWER_ON AC_OFF_DET 2
27 AC_OFF_DET TCON_ON 3
26 TCON_ON STBY3.3V 4
25 STBY3.3V TCON_12V 5
24 STBY GND
AU_GND REG_12V 6~8
21~23 TCON_GND GND 12~14

18~20 TCON_12V DIGITAL_STBY 18

12~17 REG_12V BL_ON 19
6~11 GND BL_ERR 20
20
5 BL_ON CN4803
3 BL_ERR
REG_12V (AU) 1~3
2 DIGITAL_STBY
GND (AU) 4~6

BAFS/BAF2S
G7

XBR-55X900A 8
 SECTION 2 - TROUBLESHOOTING

NO POWER FLOWCHART

No Power

Remove AC power and

wait at least 30
seconds before
reapplying.

Press power
High (>2.5V) button while
Does red Yes Yes
on Pin 1 of CN6101 monitoring Pin 7
Standby LED on
on Power Supply? of CN6601 on
front panel light?
Power Supply
Board.

No No

Yes See Stanby

Is Standby LED Power Supply High (3.3V)
LED Blinking Yes Power Supply
blinking? Board* appears
Flowchart Board*
momentarily?

No
No

Power Supply
Main Board*
Board*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 23.

XBR-55X900A 9
 SECTION 2 - TROUBLESHOOTING

STANDBY LED BLINKING FLOWCHART

Protect
Shutdown.
Standby LED
Blinking

Yes
2X Power Supply
Board*

No

Yes
10X
8X See Triage
HEM3 Chart
Board
Yes
3X Main Board*

No
No

No No No After a while
4X 5X 6X 7X Check ventilation

Yes Yes Yes Immediately

TCON* Power Supply

LCD Panel* Main Board*
(LCD Panel) Board*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 23.

XBR-55X900A 10
 SECTION 2 - TROUBLESHOOTING

NO VIDEO FLOWCHART

No Video

Locate
Backlights No CN6401 on No No
Zero volts at Zero volts at LCD Panel*
turned on? Power Supply Pin 5? Pin 3?
Board.

Yes Yes
Yes

Sony logo Yes TCON*

appears Main Board* Main Board*
(LCD Panel)
momentarily?

No

Unplug LVDS
connector with Test patterns No TCON*
unit off. Turn unit display on (LCD Panel)
back on. screen?

Yes

Main Board*

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 23.

XBR-55X900A 11
 SECTION 2 - TROUBLESHOOTING

VIDEO DISTORSION FLOWCHART

Video Distortion

Lines
Is distortion Yes Improper or No Vertical lines Yes move when Yes
across entire missing wide-mode Main Board*
or bars?
screen? colors? changed?

No Yes No No

TCON*
Main Board*
(LCD Panel)

Any horizontal Yes

LCD Panel*
lines?

No

Any single or Yes

isolated vertical LCD Panel*
lines?

No

More than 1 Yes TCON*

vertical band? (LCD Panel)

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 23.

XBR-55X900A 12
 SECTION 2 - TROUBLESHOOTING

NO 3D VIEWING

3D Not Working

Press “3D” button on

Remote Commander
and select
“Simulated 3D”.

Double images No
displayed on Main Board*
screen?

Yes

View image with No

Passive 3D Double images Passive 3D
Glasses. become one? Glasses

Yes

3D OK

*For Part Number information, refer to “Section 4 - Exploded View/Part Number Information” on page 23.

XBR-55X900A 13
SECTION 3 - REPAIR INFORMATION

REPAIRING THE TV REMOVING THE REAR COVER

1. Remove 1 screw from AC Cover and disconnect the AC Power Cord.
If the latest Software does not correct the issue, complete the following:
1. Verify the television has the symptom the customer indicated. HOLD
2. Replace part causing the symptom.
3. Install the latest version of Software (Required for ALL repairs).
4. Perform the required service adjustments and checks.
5. Verify the repair resolved the issue. 2. Remove 3 Screw Caps from the top of the Rear Cover.

REMOVING THE TABLE-TOP STAND

AND COVER UNDER
1. Place TV face down on a soft and flat surface.

3. Locate and remove all screws from the Rear Cover.

2. Grasp Cover Under as shown, then carefully pull upwards to release the
locking clips and lift to detach.

4. Grasp Rear Cover as shown and lift to detach.

3. Remove 4 screws from Table-Top Stand and pull down as shown to

detach from Rear Cover.

XBR-55X900A 14
 SECTION 3 - REPAIR INFORMATION

REPLACING THE MAIN BOARD

The Main Board used in this model is available for repair. For Part Number 4. Remove 13 screws from the Main Board, then lift to detach.
information refer to Section 4 - Exploded View/Part Number Information on
page 23.
1. Disconnect LVDS and FFC cables.
a. Press down the 2 locking clips and pull LVDS cables to release.

5. Install the new Main Board and screws.

6. Reconnect the LVDS, FFC cables, and all other connectors.
CAUTION: Make sure the black line is aligned to the connector before
locking.
b. Lift the black locking bar and pull FFC cable to release. a. Reconnect LVDS cables in the connectors and press down the 2
locking clips to secure position.

2. Disconnect remaining connectors.

b. Lift the black locking bar to reconnect the FFC Cable and secure
the connector.

3. Slide Bracket Side and Bracket Under to remove from Main Board.

7. Reconnect remaining connectors.

Side Bracket
Under Bracket

XBR-55X900A 15
 SECTION 3 - REPAIR INFORMATION

8. Update the Software. 13. Press MUTING then 0 to save the changes.
After ALL repairs UPDATE the SOFTWARE to the latest version.
Instructions are included with the Software package on the Sony
DIGITAL SERVICE
website.
002 MODEL
a. Insert the USB device with the latest Software into the TV. 001 DEST ATSC-UC_BASE
b. Press POWER to turn on the TV. WRITE
c. Wait until the Software update is complete and the TV turns OFF. 14. Press 1 until 002 MODELNAME displays.
9. Access Service Mode by pressing the following buttons within 1 second
of each other: DIGITAL SERVICE
002 MODEL
DISPLAY Channel 5 Volume + POWER
002 MODELNAME _________

10. When the DIGITAL Menu appears, press 2 until 002 MODEL
category displays.
15. Press 3 until the model displayed matches the model of the TV.
11. Press 1 until 001 DEST item displays.
CAUTION: The Model Name can only be selected once. Be sure
to verify the information is correct before saving the changes.
DIGITAL SERVICE 16. Press MUTING then 0 to save the changes.
002 MODEL
001 DEST ATSC-UC_BASE
DIGITAL SERVICE
002 MODEL
CAUTION: If the incorrect Destination Data Value is selected, it may 002 MODELNAME XBR-55X900A
corrupt the Sofware requiring a Main Board replacement.
WRITE
12. Select the correct destination of the TV , press 3 to increase or 6
to decrease the data value (Use the table below for reference). 17. Locate the Serial Number for the TV on the side of the Rear Cover.

Model Name Destination Data Value MODEL NO

XBR-55X900A US/CND ATSC-UC_BASE XBR-55X900A
SERIAL NO
1800001

XBR-55X900A 16
 SECTION 3 - REPAIR INFORMATION

18. Press 1 until 003 SERIAL item displays. 23. Clear the Self Check screen.
a. Press POWER to exit Service Mode.
DIGITAL SERVICE
b. Press the following buttons on the Remote Commander within
002 MODEL
1 second of each other:
003 SERIAL
DISPLAY Channel 5 Volume - POWER

19. Press 0 to display the Serial Number Edit option. SELF CHECK

000 RESERVED --------------------- --------------------- --------------------- 00

000 RESERVED --------------------- --------------------- --------------------- 00
DIGITAL (MODEL) SERVICE
002 MAIN_POWE --------------------- --------------------- --------------------- 00
SerialNumberEdit 003 DC_ALERT --------------------- --------------------- --------------------- 00
003 AUD_PROT --------------------- --------------------- --------------------- 00
*1 SerialNumber 003 HDMI_EQ --------------------- --------------------- --------------------- 00
003 TU_DEMOD --------------------- --------------------- --------------------- 00
004 VLED --------------------- --------------------- --------------------- 00
004 LD_ERR --------------------- --------------------- --------------------- 00
20. Press to display the Serial Number input screen. 005 HFR_ERR --------------------- --------------------- --------------------- 00
005 TCON_ERR 120123132522 120123113645 --------------------- 02 Error Count

DIGITAL (MODEL) SERVICE 005 P_ID-ERR --------------------- --------------------- --------------------- 00

006 BACKLITE --------------------- --------------------- -------------------- 00
SerialNumberEdit
007 TEMP_ERR --------------------- --------------------- --------------------- 00
*1 SerialNumber 007 FAN_ERR --------------------- --------------------- --------------------- 00
Please Input serial number 010 EMITTER --------------------- --------------------- --------------------- 00
(0000000-99999999) 101 VPC_WDT --------------------- --------------------- --------------------- 00
_______ 102 MEPS_WDT --------------------- --------------------- --------------------- 00
103 HOST_WDT --------------------- --------------------- --------------------- 00
CAUTION: The Serial Number can only be selected once. Be sure 104 STBY_WDT --------------------- --------------------- --------------------- 00
to verify the information is correct before saving the changes.
00345 000333 06789
21. Enter the Serial Number of the TV.
c. To clear the error history and error count press 8 0 .
NOTE: If the incorrect Serial Number is entered, press RETURN
to go back to the Serial Number input screen and re-enter d. Press POWER to exit Self Check Mode.
the correct number.
24. Cycle AC Power (Unplug and plug AC Cord from the outlet).
22. Press to save the Serial Number.

DIGITAL (MODEL) SERVICE

SerialNumberEdit
*1 SerialNumber
1800001 WRITE

XBR-55X900A 17
 SECTION 3 - REPAIR INFORMATION

REPLACING THE POWER SUPPLY BOARD

1. Disconnect all connectors from the Power Supply Boards. c. Insert the USB device with the latest Software into the TV.
d. A message will appear starting the update automatically.

2. Remove all screws from the board to be replaced and lift to detach.

NOTE: If the latest Software version was previously installed, a

different message will appear on the screen. In this case, please refer
to step “f”.

3. Install the new Power Supply Board, screws and connectors. e. Wait approximately 5 minutes until the Software installation is
completed and a successful update message appears.
4. Update the Software. CAUTION: TV will turn ON and OFF during this process.
After ALL repairs UPDATE the SOFTWARE to the latest version.
Instructions are included with the Software package on the Sony website.
a. Insert the USB device with the latest Software into the TV.

b. Press POWER to turn on the TV.

c. Wait until the Software update is complete and TV turns OFF.

REPLACING THE CX BOARD f. After removing the USB device, press POWER to turn TV OFF.
1. Update the Software.
Software MUST BE updated with the latest version before replacing the 2. Remove 2 screws and disconnect connector from CX Board to detach.
CX Board. Use the latest version of PKG.3.504 or higher.
a. Press POWER to turn ON the TV.
b. Wait until Set Up screen shows up, then skip all initial settings if
needed.

XBR-55X900A 18
 SECTION 3 - REPAIR INFORMATION

3. Replace the CX Board with the new CX2 Board, install screws and 9. Press MUTING then 0 to save the changes.
connector.
10. Press 1 until 003 CHECK_SPI_FW item displays.
4. Access Service Mode by pressing the following buttons within 1 second
of each other:
CHASSIS SERVICE
DISPLAY Channel 5 Volume + POWER 004 HDMI
003 CHECK_SPI_FW 0
5. Press OPTION until the CHASSIS Menu appears.

CHASSIS SERVICE 11. Press 3 to increase the data value from “0” to “1”.
000 WYVERN
000 S2_NOISE_TH 32 CHASSIS SERVICE
004 HDMI
003 CHECK_SPI_FW 1
6. Press 2 until 004 HDMI displays.

CHASSIS SERVICE 12. Press MUTING then 0 to save the changes.

004 HDMI 13. Cycle AC Power (Unplug and plug AC Cord from the outlet).
000 FORCE_ARC 0
14. When normal OSD (On Screen Display) graphics appear, wait 10
seconds and cycle AC Power again.

7. Press 1 until 002 RUN_EDID_SEQ item displays. 15. TV turns ON with normal OSD.
16. Prepare TV to install the Software again.
CHASSIS SERVICE Since the TV already has the latest Software installed, it must be “forced”
004 HDMI to install the latest version.
002 RUN_EDID_SEQ 0 a. Press POWER to turn OFF the TV.
b. Access Service Mode by pressing the following buttons within 1
second of each other:
8. Press 3 to increase the data value from “0” to “1”.
DISPLAY Channel 5 Volume + POWER

CHASSIS SERVICE
004 HDMI
002 RUN_EDID_SEQ 1

XBR-55X900A 19
 SECTION 3 - REPAIR INFORMATION

17. Press OPTION until the CHASSIS Menu appears. REPLACING THE SWITCH UNIT
1. Disconnect 2 connectors from the Switch Unit, then remove 2 screws
CHASSIS SERVICE and lift to detach.
000 WYVERN
000 S2_NOISE_TH 32

18. Press 2 until 007 DL displays.

2. Install the new Switch Unit, screws and connectors.
CHASSIS SERVICE
007 DL
000 PID_DATA_MISMAT 0 REMOVING THE WOOFER SPEAKER
1. Disconnect connector from Woofer Speaker, remove 5 screws and lift to
detach.
19. Press 3 to increase the data value from “0” to “1” from the
000 PID_DATA_MISMAT item.

CHASSIS SERVICE
007 DL
000 PID_DATA_MISMAT 1
2. Refer to these instructions to remove the opposite Woofer Speaker.

20. Install the Software. REMOVING THE WLAN MODULE AND HW BOARD
a. Press POWER to turn TV OFF. 1. Disconnect connector, remove 2 screws and lift to detach the Bracket
Module.
b. Wait 5 seconds and insert the USB device with the latest
Software into the TV.
NOTE: Display will not be shown on the TV during the update.
If the USB drive has an indicator light, it will start blinking.
Bracket Module
CAUTION: Must use the same version as the first update.
c. Wait aproximatelly 5 minutes, until TV turns ON and a successful
update message appears.
d. Remove USB device.

XBR-55X900A 20
 SECTION 3 - REPAIR INFORMATION
2. Release 3 locking clips to detach the Cover Module from Bracket Under, 2. Locate and remove 2 screws from PWB Board, then release harness to
then remove HW Board. detach.

HW Board PWB Board

Bracket
Cover Under
Module

3. Release 3 locking clips to detach the WLAN Module. 3. Carefully disconnect all remaining connectors from PWB Board and lift
to detach.

WLAN
Module

REMOVING THE SIDE SPEAKERS 4. Lift Speaker (80MM) to detach. Release 2 locking clips to remove
Speaker Bracket and lift Speaker Ornament to detach.
1. Remove 14 screws from Speaker Cover, lift as shown to disconnect
connector from PWB Board, then slide it through the Speaker Cover
opening to detach. Speaker
Bracket

Speaker (80MM) Speaker

Ornament

5. Remove 2 screws from Speaker (18MM) and lift to detach.

NOTE: Use a 7mm Metric Nut Driver to remove: Speaker (18MM)

Spacer (SP-RC), HEX.
6. Remove 2 screws from TW Bracket and lift to detach.

TW Bracket

XBR-55X900A 21
 SECTION 3 - REPAIR INFORMATION
7. Lift Loud Speaker to detach. Release 2 locking clips to remove Speaker 4. Release the HSF Board connector from the locking clip to disconnect
Bracket and lift Speaker Ornament to detach. it and lift to detach. Then, disconnect and remove HSF Board, FPC-BT
and Bluetooth Module.

Speaker HSF Board

Bracket FPC-BT

Loud Speaker Speaker

(Passive Radiator) Ornament
Bluetooth
Module
8. Refer to these instructions to remove the opposite Side Speakers.
5. Locate HIF Board and slide upwards to detach.

REMOVING THE SMART CORE BLOCK HIF Board

1. Locate and remove 7 screws shown below. Lift Neck Brackets and
Under Bracket (SC) to detach from Rear Cover.

Under
Neck
Bracket (SC) REMOVING THE TS BOARD
Brackets
1. Locate the TS Board on the upper side of the TV, disconnect 1 connector
and remove 1 screw, then lift to detach.
2. Disconnect connector and hold Smart Core Block as shown, then twist it
downwards to release.

TS Board

3. Unclamp 2 side locking clips from Lid, SC and lift to detach.

Lid, SC

XBR-55X900A 22
SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

XBR-55X900A Components not identified by a part number or description

are not stocked because they are seldom required for routine
The component parts of an assembly are indicated by the reference numbers in
the far right column of the parts list and within the dotted lines of the diagram.
service.
NOTE: The components identified by shading and ! NOTE: The components identified by a red outline and a mark contain confidential
mark are critical for safety. information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

REF. NO. PART NO. DESCRIPTION

1 4-471-530-01 STAND
2 4-462-872-01 NECK, STAND

XBR-55X900A 23
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

NOTE: The components identified by shading and ! NOTE: The components identified by a red outline and a mark contain confidential
mark are critical for safety. information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

REF. NO. PART NO. DESCRIPTION

51 4-454-653-01 REAR COVER

52 4-457-577-01 LABEL, HDMI
FOR SERIAL No. 1800001 - 6010000 ONLY.
52 4-469-810-01 LABEL, HDMI BLANK
61
FOR SERIAL No. 6010001- 6710000 ONLY.
53 4-457-575-01 LABEL, SIDE TERMINAL
62 64
60
54 4-457-576-01 LABEL, UNDER TERMINAL
FOR SERIAL No. 1800001 - 6010000 ONLY.
60
59
63
54 4-449-086-41 LABEL, UNDER TERMINAL
FOR SERIAL No. 6010001- 6710000 ONLY.

55 4-449-005-01 LABEL, REAR TERMINAL

56 4-454-665-03 COVER, UNDER
57 4-299-531-01 AC COVER
! 58 1-839-679-12 POWER SUPPLY CORD

59 1-474-516-11 G6 BOARD, COMPLETE

60 4-298-004-01 SPACER (B)
61 1-474-517-11 G7 BOARD, COMPLETE

62 A-1938-830-A BAFS BOARD, COMPLETE

FOR SERIAL No. 1800001 - 6010000 ONLY.
AFTER REPLACING THE MAIN BOARD, YOU MUST UPDATE
51
THE SOFTWARE TO THE LATEST VERSION.
57 62 A-1951-645-A BAF2S BOARD, COMPLETE
58
FOR SERIAL No. 6010001- 6710000 ONLY.
AFTER REPLACING THE MAIN BOARD, YOU MUST UPDATE
52 THE SOFTWARE TO THE LATEST VERSION.
54
55
56 63 4-460-567-31 BRACKET, UNDER (MOLD)
FOR SERIAL No. 1800001 - 6010000 ONLY.
53
63 4-439-633-22 BRACKET, UNDER (MOLD)
FOR SERIAL No. 6010001- 6710000 ONLY.
64 4-460-567-31 BRACKET, SIDE (MOLD)

XBR-55X900A 24
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

NOTE: The components identified by shading and ! NOTE: The components identified by a red outline and a mark contain confidential
mark are critical for safety. information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

REF. NO. PART NO. DESCRIPTION

101 NA LCD PANEL

FOR ALL LCD PANEL AND TCON BOARD PART NUMBER
INFORMATION REFER TO THE LCD PANELS SERVICE MANUAL.
111
102 A-1936-361-A CX BOARD, MOUNTED
FOR MODELS WITH BAFS BOARD ONLY.
PLEASE CONFIRM THE INFORMATION ON THE ORIGINAL
BOARD LABEL BEFORE ORDERING THIS PART.
113 AFTER REPLACING THE CX BOARD YOU MUST UPDATE
112
THE SOFTWARE TO THE LATEST VERSION.

102 A-1952-947-A CX2 BOARD, MOUNTED

113
FOR MODELS WITH BAFS BOARD ONLY.
PLEASE CONFIRM THE INFORMATION ON THE ORIGINAL
BOARD LABEL BEFORE ORDERING THIS PART.
110 101
109 AFTER REPLACING THE CX2 BOARD YOU MUST UPDATE
THE SOFTWARE TO THE LATEST VERSION.

108 103 1-492-349-11 SWITCH UNIT

107 104 4-457-451-01 SHEET, THERMAL
105 4-454-677-01 BRACKET, NECK

106 4-454-662-03 BRACKET, UNDER (SC)

102 107 4-455-891-01 BRACKET, MODULE
104
105
05
106 108 4-463-081-01 COVER, MODULE
109 A-1936-362-A HW BOARD, MOUNTED
105 Bracket 110 1-492-076-11 WLAN, MODULE
HUS*

111 4-457-516-11 SHEET, INSULATION

103
ORDER THIS PART WHEN REPLACING THE LCD PANEL.
*Reinstall Bracket HUS when replacing the LCD Panel. 112 A-1936-365-A TS BOARD, MOUNTED
113 4-457-426-01 GASKET (BAF)

XBR-55X900A 25
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

NOTE: The components identified by shading and ! NOTE: The components identified by a red outline and a mark contain confidential
mark are critical for safety. information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

REF. NO. PART NO. DESCRIPTION

151 4-454-657-01 COVER, SP (LEFT)

162
ORDER THIS PART WHEN REPLACING THE LCD PANEL.
152 1-895-387-11 PWB BOARD MOUNTED (NETWORK)
153 1-858-894-11 LOUD, SPEAKER (80MM)
153 154 4-478-227-01 BRACKET, SP
154 152 ORDER THIS PART WHEN REPLACING THE LCD PANEL.

155
155 4-454-664-01 ORNAMENT, SP
156 156 1-858-893-11 LOUD SPEAKER (18MM)
158
157 157 4-454-659-01 BRACKET, TW
154
ORDER THIS PART WHEN REPLACING THE LCD PANEL.
155
158 1-858-896-11 LOUD SPEAKER (PASSIVE RADIATOR)
159 4-454-660-01 COVER, WOOFER (LEFT)
160 1-858-895-11 SP BOX ASSEMBLY

161 4-454-661-01 COVER, WOOFER (RIGHT)

162 4-454-658-01 COVER, SP (RIGHT)
ORDER THIS PART WHEN REPLACING THE LCD PANEL.
152

155 151
154

160 153
157
Smart Core
ore
Block 156
161 155
154
158

160

159

XBR-55X900A 26
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

SMART CORE BLOCK NOTE: The components identified by shading and ! NOTE: The components identified by a red outline and a mark contain confidential
mark are critical for safety. information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

REF. NO. PART NO. DESCRIPTION

201 4-463-080-01 LID, SC

202 A-1936-360-A HIF BOARD, MOUNTED
203 1-846-688-11 FPC BT
ORDER THIS PART WHEN REPLACING BLUETOOH MODULE
OR HSF LM BOARD.

204 A-1936-358-A HSF LM BOARD, MOUNTED

205 1-492-062-11 BLUETOOTH MODULE
206 4-454-668-01 CASE BARE, SC

201

202

203

204

205

206

XBR-55X900A 27
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

CONNECTORS NOTE: The components identified by shading and !

mark are critical for safety.
NOTE: The components identified by a red outline and a mark contain confidential
information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

252
259

253 260

257
254

251
255

258

256

REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION
251 1-846-696-11 LEAD WIRE WITH CONNECTOR 51P 256 1-910-107-76 HARNESS ASSEMBLY (BAF)
FOR SERIAL No. 1800001 - 6010000 ONLY. 257 1-910-107-75 CONNECTOR ASSEMBLY 28P
252 1-910-107-83 CONNECTOR ASSEMBLY 3P (BAF-TS) 258 1-846-714-11 CONNECTOR ASSEMBLY 3P (G6-G7)

253 1-910-107-78 (LVDS) FLEXIBLE FLAT CABLE 20P 259 1-910-107-77 HARNESS ASSEMBLY (G6/G7-LD)
254 1-846-694-11 (LVDS) FLEXIBLE FLAT CABLE 41P 260 1-910-107-74 CONNECTOR ASSEMBLY 5P
255 1-846-692-12 (LVDS) FLEXIBLE FLAT CABLE 51P

XBR-55X900A 28
 SECTION 4 - EXPLODED VIEW/PART NUMBER INFORMATION

SCREWS NOTE: The components identified by shading and !

mark are critical for safety.
NOTE: The components identified by a red outline and a mark contain confidential
information. Specific instructions must be adhered to whenever these components are
Replace only with part number specified. repaired and/or replaced. (See Appendix A)

P/N DESCRIPTION XBR-55X900A

Speaker Box Assembly Right (5), Speaker Box Assembly Left (5),
4-256-393-01 SCREW, +PSW M3X6 W12
AC Cover (1), Woofer Cover Right (1), Woofer Cover Left (1)

4-268-126-02 SCREW ORNAMENTAL M6X12 Rear Cover (4)

4-457-815-02 SCREW, +PSW M3X6 STEP Rear Cover (18)

7-685-647-79 SCREW, +BVTP 3X10 TYPE IT-3 Rear Cover (2), Loud Speakers 18MM (4), Smart Core Block (1)

Bracket Module (2), CX Board (2), Switch Unit (2), Main Board (13),
2-990-421-41 SCREW, (+PSW) (M3X6) Bracket HUS (2), TS Board (1), TW Brackets (4), Mounted PWBs (4),
Power Supply Board G7 (5), Power Supply Board G6 (5)

7-682-949-09 SCREW, + PSW 3X10 Speaker Cover Right (12), Speaker Cover Left (12)

4-159-298-01 SCREW, + PSW M4X10 Neck Bracket Right (3), Neck Bracket Left (3)

4-457-814-01 SPACER (SP-RC), HEX Speaker Cover Right (2), Speaker Cover Left (2)

2-580-607-01 SCREW, +PSW M5X12 Table Top Stand to TV (4), Neck Stand Left (2), Neck Stand Right (2)

XBR-55X900A 29
SECTION 5 - ACCESORIES/PART NUMBER INFORMATION
ACCESSORIES AND PACKAGING OPTIONAL ACCESSORIES
PART NO. DESCRIPTION PART NO. DESCRIPTION

2-580-607-01 SCREW, +PSW M5X12 4-414-470-01 SUPPORT BELT KIT

(SCREWS TO ATTACH TABLE-TOP STAND TO LCD TV) X-2586-996-1 PASSIVE 3D GLASSES
For product protection and safety reasons, Sony strongly recommends
that you use the screws provided with the TV.
CAUTION: These screws cannot be used to secure the TV
REMOTE COMMANDER
to the Wall Mount Brackets.
PART NO. DESCRIPTION

4-462-778-11 MANUAL, INSTRUCTION (ENGLISH VERSION) 1-491-987-11 REMOTE COMMANDER (RM-YD087)

4-462-778-21 MANUAL, INSTRUCTION (FRENCH VERSION) 1-492-077-12 ONE TOUCH REMOTE CONTROL (RMF-YD001)
4-464-369-11 SUPPLEMENT (STAND INSTALLATION)

MISCELLANEOUS
PART NO. DESCRIPTION

4-273-074-14 FLYER, SAFETY

4-463-174-01 BADGE, XBR LOGO (H6)
4-462-315-01 SCREW CAP

4-262-708-04 CLAMPER, CABLE

4-441-738-01 CLAMPER CABLE (L)
4-096-737-01 CUSHION (G)
4-454-669-01 PANEL ORNAMENT, SC

7-600-031-96 TAPE (3M 1350FW-1) 15MMX66M WHT

7-600-031-97 TAPE (3M 1350FB-1) 15MMX66M BLK
4-465-860-01 TAPE_95

XBR-55X900A 30
APPENDIX A: ENCRYPTION KEY COMPONENTS
Encryption key components developed by Sony Corporation contain confidential information and shall be handled under the non-disclosure obligations provided
in the applicable agreement with Sony Corporation (and/or its subsidiary).
As part of this agreement specific instructions must be adhered to whenever a Circuit Board containing encryption key components is repaired and/or replaced
pursuant to the following:
1. In the service manual the Circuit Board(s) containing encryption key components shall be identified with a red outline and a .
2. Only repair boards or components listed in the service manual shall be utilized for replacement and/or repair.
3. Disassembly, decryption or reverse-engineering component(s) is strictly prohibited.
4. Any board in which the Servicer replaces an encryption key component must be placed back into the set it orignally came from and the replaced
defective component MUST BE DESTROYED. Boards cannot be swapped.
5. If a Circuit Board identified with a red outline and a in the service manual is deemed to be defective:
a. and if a core charge is imposed and is covered under the product warranty, the defective un-repaired or modified board MUST BE RETURNED to
Sony.
b. and if the core charge is NOT covered under the product warranty, the defective un-repaired or modified board MUST BE DESTROYED.
6. If a unit is destroyed (such as field scrap), the Circuit Board identified with a red outline and a in the service manual MUST BE DESTROYED.

is a trademark of Sony Electronics.

Reproduction in whole or part without written permission is prohibited. All rights reserved.
Sony Corporation
Sony LCSC English
Technical Services 2013CJ74WEB-1
9-888-524-03 Service Publications Department © 2013.3

XBR-55X900A A-1