CONSTRUCTION SILICONE
GUIBA O 882 SILICONE
INSULA TING GLA SS
Two part silicone sealant suited SEA LA NT
for the secondary seal in
insulating glass units BASIC USES
GUIBAO 882 SILICONE INSULATING GLASS SEALANT is
FEATURES
specially designed for use as secondary sealant for insulating glass
Two part, neutral fast cure rate,
units.
suitable for factory application
High level of tensile strength and
TYPICAL PROPERTIES
mechanical properties
These values are not intended for use in preparing specifications.
Excellent adhesion to a wide range
of substrates including coated glass, Test Method Property Unit Standard Result
low -E glass, tempered glass, GB/T 13477 (ISO 7390) Slump mm ≤3 0
laminated glass, aluminum and
Extrudability
steel spacers etc. GB/T 13477 (ISO 9048) (after 20 min.) s ≤10 1.4
Excellent weatherability and high
GB/T 13477(ASTM D 2377) Tack Free Time h ≤3 1.0
resistance to ultra-violet radiation,
GB/T 531.1 (ISO 7619 ) Hardness Shore A 30～60 47
heat and humidity, and ozone
53113477
Excellent resistance to temperature GB/T 13477 (ISO 8339) Tensile Strength MPa ≥0.6 0.8
extremes, unaffected performance Adhesion
GB 16776 % ≤10 0
Failure
from –50 ℃ to +150 ℃
GB 16776 (ASTM C 792) Heat Aging
Good compatibility with other
Weight Loss % ≤6 4.5
neutral silicone sealants
Chalking Nil Nil
Cracking Nil Nil
COLOURS
Part A (base) of GUIBAO 882 is *GB: Chinese National Standard
ASTM: American Society for Testing and Materials
available in white, part B (curing agent)
ISO: International Standardization Organization
in black, black color after mixing.
PACKAGING
GUIBAO 882 is available in kit: part A in 200L drums (net 180L，
190L ), part B in 20L pails (net 18L,19L).
SPECIFICATIONS
GUIBAO 882 is designed to meet or even exceed the requirements of
Chinese national specification
GB/T 29755-2013
STORAGE AND SHELF LIFE
atmospheric moisture, therefore should not be
GUIBAO 882 should be stored in original unopened
containers. It has a shelf life of 12 months from the
exposed to air for prolonged periods of time.
date of manufacture.
LIMITATIONS Priming
GUIBAO 882 should not be applied: Priming is not usually required when using GUIBAO
For structural glazing 882. But it is essential that adhesion is tested prior to
To the materials that bleed oils, plasticizers or use to decide whether to use primer or not.
Masking and Tooling
solvents, such as impregnated wood, oil-based
Areas adjacent to joints may be masked to ensure a
caulks
neat sealant line Do not allow mask tape to touch clean
To frost laden or damp surfaces
surfaces to which the silicone sealant is to adhere.
For continuous water immersion
Tooling should be completed in one continuous stroke
When surface temperature below 4℃ or over 50℃
after sealant application. Masking tape should be
removed immediately after tooling.
HOW TO USE
Surface Preparation
Equipment Cleaning
Clean all joints removing all foreign matter and
When not being used, it is recommended that the
contaminants such as oil, grease, dust, water, frost, old
dispensing equipment be purged either with the base
sealants, surface dirt, or glazing compounds and
component or flush with suitable solvent.
protective coatings.
Mixing and Dispensing SAFETY INFORMATION
To obtain the optimal performance of GUIBAO 882, it GUIBAO 882 is a chemical product, not edible, no
is recommended that base and curing agent thoroughly implantation into body and should be kept away
mixed using a two-part silicone dispensing machine. from children.
Cured silicone rubber can be handled without any
GUIBAO 882 should be mixed at a ratio of 9:1～11:1 risk to health.
base to curing agent by volume, or 15:1～17:1 base to Should uncured silicone sealant contact with eyes,
curing agent by weight for optimal performance. rinse thoroughly with water and seek medical
treatment if irritation persists.
Lot matching of GUIBAO 882 base to curing agent is Avoid prolonged exposure of skin to uncured
silicone sealant.
not required. Before use, it is recommended that
Good ventilation is necessary for work and cure
places.
curing agent be stirred to ensure the
TECHNICAL SERVICES
homogeneity of all components.
Complete technical information and literature,
adhesion testing and compatibility testing are available
from Guibao.
GUIBAO 882 part B curing agent will react with
DISCLAIMER
The information presented herein is offered in good
faith and is believed to be accurate. However, because
conditions and methods of using our products are
beyond our control, this information should not be used
in substitution for customer’s tests to ensure that our
products are safe, effective, and fully satisfactory for
specific applications.
Manufacturer
Chengdu Guibao Science and Technology Co.,Ltd.
No.16, Xinyuan Road, I-tech Zone, Chengdu 610041
P.R.CHINA
Tel: +86 28 8531 1860
Fax: +86 28 8531 8066
E-mail:[email protected]
www.cnguibao.com
