BOSTIK SEAL ‘N’ FLEX® FAÇADE H725

®
SEAL ‘N’ FLEX
FACADE H725
LOW MODULUS HYBRID CONSTRUCTION SEALANT
®
6th August 2021

YOUR SMART ADVANTAGES

SEAL N FLEX PRODUCT CHARACTERISTICS



ONE PLUS P590
UV, moisture and weather resistance
Bubble free curing
Viscosity Non-sag, smooth
thixotropic paste

 Low modulus Cure method Moisture curing


LOW MODULUS POLYURETHANE SEALANT
±50% joint movement on glass, concrete & aluminum
Application temperature 5 to 40°C
 Free of isocyanates, silicones & solvents
®
 Easy tooling
 Permanently elastic EAL N FLEX
 Excellent adhesion without primer to most, even
Product codes
290ml cartridge/ 20 per carton
damp, surfaces Grey 30619351
 Paintable*
ONE PLUS P590 White
Black
600ml sausages/ 20 per carton
30619353
30619349

USES
LOW MODULUS POLYURETHANE
Grey SEALANT 30619352

Bostik Seal ‘N’ Flex® Facade H725 is a high quality White 30619354
professional low modulus sealant based on hybrid Black 30619350
technology. It cures under the influence of humidity to
form a durable elastic rubber. Bostik Seal ‘N’ Flex Façade
H725 is resistant to weathering conditions such as rain,
UV, snow, sleet, ozone, atmospheric contamination and TYPICAL PERFORMANCE DATA (approx.)
pollution. Can be used on:
Temperature resistance -30 to +70°C
 Insitu concrete floors and walls
Skin time 90 minutes
 Precast and tilt up panels
 Glazing application Cure rate 2-3mm/24 hours
 Brickwork and blockwork @ 23°C/50%RH on porous
 Rendered masonry
substrates
 Plasterboard
 Fiber cement sheet Full cure 7 days on porous
substrates. Allow 14
CERTIFICATIONS days in joints over
 ASTM C920 20mm wide.
 ASTM C1248
 F-EXT-INT-CC 25LM: EN 15651-1 for Façade Joints Specific gravity 1.34 g/ml
 PW-EXT-INT-CC 25LM: EN 15651-4 for Pedestrian
Walkways Shore A hardness 25
 EMICODE EC1 PLUS
100% Modulus 0.45 N/mm2
 SNJF F25E
 Branz Appraisal: natural weathering test for up to 11
Tensile strength 1.3 N/mm²
years and accelerated weatherometer (UV) aging test
for up to 7000 hours. Elongation at break 600%

Total joint movement ±50%

Maximum joint width Up to 50mm

Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 1

Page 1 of 3
 BOSTIK SEAL ‘N’ FLEX® FAÇADE H725

DIRECTIONS FOR USE JOINT SEALING

Read and understand the Safety Data Sheet before using A joint with the correct dimensions is able to absorb
this product. SDS can be acquired by visiting movements between building materials. Always use a
www.bostik.com.au. backing rod for correct sealant geometry and contact
with the substrate.
SURFACE PREPARATION - Prime after the installation of backing rod
1. Application temperature + 5°C to + 40°C (applies to - Ensure maximum adhesion to the bond face
environment and substrates) - Minimum allowable joint depth is 5mm
2. Clean and dry all surfaces by removing foreign matter - Maximum allowable joint width is 50mm
and contaminants such as laitance oil, dust, grease, - Tool sealant to achieve concave shape
frost, water, dirt, old sealants, curing agents and any
protective coating
3. Dust and loose particles should be vacuum cleaned.

PRIMING
Bostik H725 Seal ‘N’ Flex Façade H725 adheres perfectly
without the use of a primer to most porous & non-porous
substrates. Some porous substrate may require pre-
treatment with Bostik Simson Prep P (refer to Bostik
Simson Prep P Technical Data Sheet for more details)
Always test adhesion prior to application.
Joint Width to Depth ratio:
IMPORTANT: For optimum adhesion and in areas of
critical, high performance applications such as high stress Width Depth
joints, extreme weather exposure or surfaces that are
too porous, the use of substrate primer is required. Min 5mm to 10mm 1:1 ratio

i.e. A 10mm width will require

10mm depth
APPLICATION
𝑾𝒊𝒅𝒕𝒉 (𝒎𝒎)
Bostik Seal ‘N’ Flex Façade H725 should be dispensed >10mm, up to 50mm Depth (mm) = +𝟔
from either the cartridge or sausage by means of a 𝟑
caulking gun. i.e. A 16mm joint width will
require a 12mm depth:
Cartridge application: 16
Depth (mm) = + 6 = 12mm
1. Pierce the membrane at the top of the top of the 3
cartridge and screw on the nozzle
2. Cut the nozzle to give the required angle and bead size
3. Place the cartridge in a caulking gun and squeeze the
COVERAGE
trigger
The estimated lineal metre yield per pack size is
recommended in the following table. No allowance has
Sausage application:
been made for waste or irregular joint geometry.
1. Clip the end of the sausage and place in a barrel gun
2. Screw the end cap and nozzle onto the barrel gun
Joint 5mm x 10mm x 20mm x 50mm x
3. Use the trigger to extrude the sealant. To stop; depress
(W x D) 5mm 10mm 10mm 25mm
the catch plate.
300ml Cartridge 12 3 1.5 0.24

Apply sealant in a continuous operation using enough 600ml Sausage 24 6 3 0.48

pressure to properly fill the joint. Tool off the surface of
W=Joint width (mm). D=Joint depth (mm).
the sealant with an appropriate sized spatula or trowel.
Apply sufficient pressure to leave a smooth, consistent
surface and ensure maximum contact with the interface
of the joint

Tool the sealant with adequate pressure to spread the

sealant against the back up material and onto the joint
sides. Excess sealant should be wiped from all surfaces
while still uncured. Remove any masking tapes prior to
sealant curing

Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 1

Page 2 of 3
 BOSTIK SEAL ‘N’ FLEX® FAÇADE H725

CLEANING STORAGE AND SHELF LIFE

Clean off uncured material, hands and equipment Store in cool (between 5°C to 25°C) dry, well- ventilated
immediately after use using Bostik Handy Wipe towels. area out of direct sunlight. Shelf life is 15 months from
Cured material can be removed by mechanical means production date in original unopened packaging and
only. correct storage conditions.

PAINTABILITY VOC INFORMATION

Bostik Seal ‘N’ Flex Façade H725 is paintable with water 1.8 g/L
based and most 2 component paints. Synthetic paints can
dry slower. We recommend testing compatibility with
paint prior to application. If Bostik Seal ‘N’ Flex Façade
H725 is being painted over (not necessary), it is
recommended to slightly sanding the sealant and the
junction surfaces prior to use. For best results, we BOSTIK HOTLINE
recommend painting within a few days of application.
Smart help 1800 267 845
LIMITATIONS
Not recommended for:
- Use in chlorinated water such as swimming pools,
spas, etc.
- PE, PP, PC, PMMA, PTFE, soft plastics, neoprene and
bituminous substrates
- Application to cement based substrates within 28
days of initial pour or set
- Applied in temperatures below 5°C or above 40°C
- Applied to joints less than 5mm in width and depth
- Applied on joints larger than 50mm

As all substrates and conditions are different, it is

strongly recommended that the applicator, or end user
conducts their own tests and ensure the product meets
their own end use requirements

This datasheet is for the general help of users. It is provided in good faith. The data is current and accurate to the best of our knowledge. Differing
materials, substrates, environments, site conditions, and product storage, handling and application may affect results. Users should carry out
tests to decide the product’s suitability for purpose. This data sheet and the properties of the product may change without notice. Users,
suppliers and retailers should check that the data sheets they have are the latest. To the maximum extent permitted by law, Bostik disclaims all
warranties in relation to manufacture and use of the product. Bostik is not liable for representations made by users, suppliers or retailers about
the product. Bostik is not liable for any loss or damage resulting from incorrect, careless, or negligent use or storage of the product, including use
of out of date product. Any liability arising from use of the product is limited to the replacement or purchase price of the product. Bostik does not
exclude rights and remedies that cannot be excluded by legislation, for example under the Australian Consumer Law (ACL). Sale of the product by
Bostik is subject to the Bostik Australia Proprietary Limited Conditions and Terms of Sale. For more information on Bostik, products, and
conditions of use and sale visit www.bostik.com/au

Bostik Australia Pty Ltd, Level 1, 6 English Street, Essendon Fields, Victoria, 3041, Australia. www.bostik.com/au
Version 1

Page 3 of 3