10/100 Mbps Ethernet to USB 2.

0 Network LPR
Print Server

Actual product may vary from photos

User Manual
SKU#: PM1115U2
For the latest information and specifications visit
www.startech.com/PM1115U2

Manual Revision: 04/08/2020

Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

1
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être effectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei fili elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

2
Table of Contents
Compliance Statements.........................................................................1
Safety Statements...................................................................................2
Product Diagram.....................................................................................5
Front View..................................................................................................................................................... 5
Rear View....................................................................................................................................................... 6

Product Information...............................................................................7
Packaging Contents................................................................................7
System Requirements.............................................................................7
Operating Systems.................................................................................................................................... 7

Hardware Installation.............................................................................8
Installing the Power Adapter Clip........................................................................................................ 8
Removing the Power Adapter Clip...................................................................................................... 8
Connecting a Printer................................................................................................................................. 9

Software Installation..............................................................................9
Setting Up the Print Server Using the Software.............................................................................. 10
Manually Setting up the Print Server.................................................................................................. 13

Setting Up a Printer in Windows...........................................................14

Setting Up a Printer in macOS...............................................................19
Performing a Hard Factory Reset..........................................................23

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

3
Software Operation................................................................................23
Accessing the Web Interface.................................................................................................................. 23
Changing the Screen Language........................................................................................................... 23
Viewing Server Information/Device Information........................................................................... 24
Viewing/Configuring Network Settings............................................................................................. 25
Restarting a Device.................................................................................................................................... 27
Resetting the Device to Factory Settings.......................................................................................... 28
Creating/Changing a Password............................................................................................................ 29

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

4
Product Diagram
Front View
1

2 3 4 5

1 Power LED
2 Power Jack
3 Link LED
4 RJ45 Port
5 Activity LED

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

5
Rear View

1 Recessed Reset Button (side)

2 USB-A Port

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

6
Product Information
Packaging Contents
• Print Server x 1
• Universal Power Adapter (NA/UK/EU/AU) x 1
• RJ45 Cable x 1
• Driver CD x 1
• Quick-Start Guide x 1

System Requirements
Operating system requirements are subject to change. For the
latest requirements, please visit www.startech.com/PM1115U2.
Operating Systems
• The Print Server is Operating System (OS) independent.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

7
Hardware Installation
Installing the Power Adapter Clip
1. Remove the Power Adapter from the box.
2. Locate the Power Clip specific to your region (e.g. U.S.).
3. Align the Power Clip with the Contact Prongs on the Power
Adapter so that the two Tabs on the Power Clip are aligned
with the cutouts on the Power Adapter.
4. Rotate the Power Clip clockwise until you hear an audible
click indicating that the Power Clip is properly attached to
the Power Adapter.
Removing the Power Adapter Clip.
1. Push and hold the Power Clip Release button on the Power
Adapter just below the Power Clip.
2. While holding the Power Clip Release button rotate the
Power Clip counter-clockwise until the Power Clip releases
from the Power Adapter.
3. Gently pull the Power Clip away from the Power Adapter.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

8
Connecting a Printer
1. Connect a USB 2.0 Cable (not included) to the USB-A Port
on the Print Server and the other end to a USB-A port on a
Printer.
2. Connect the Universal Power Adapter to the Power Jack
on the back of the Print Server and to an AC Electrical
Outlet. The Power LED will illuminate green to indicate that
the Print Server is turned on and correctly connected to the
Network.

Software Installation
Installing the Print Server Setup Software
1. Connect an CAT5e/6 Cable to the RJ45 Port on the Print
Server and to a Router or Network Device.
2. On the computer that’s connected to the same router or
network, download the drivers from www.startech.com/
PM1115U2.
3. Click on the Support tab, under Drivers and select the
appropriate driver package.
4. Once you have download and unzipped the driver. Click on
the Installation Guide PDF and follow the instructions.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

9
Setting Up the Print Server Using the Software
1. Click the Network Printer Wizard shortcut on your desktop.

Network Printer Wizard Shortcut

2. The Network Printer Wizard will appear.

Network Printer Wizard

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

10
 3. Click the Next button.
4. Select a Printer from the list to setup and click the Next
button.
Note: If no Printers are listed, make sure that the Printer
and the LPR Print Server is powered on and connected to
the network.
5. Select a Driver from the list and click the Next button,
proceed to step 9.

Select a Driver from the List

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

11
 6. If the Driver is not listed either insert the Driver CD that
came with the printer into the Host Computer’s CD or
DVD Drive and click the Have Disk button or or access the
printer’s manufactuerer website to download the required
driver.
7. Navigate to the correct Driver folder based on the printer
and click on the Driver folder.
8. Select the correct Driver and click Open. The Driver will
now appear on the list of drivers within the Network Printer
Wizard.
9. When you have selected the correct Driver from the list click
the Finish button.

Click on the Finish Button

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

12
Manually Setting up the Print Server
1. Connect a CAT5e/6 Cable to the RJ45 Port on the Print
Server and to a Computer.
2. Set your network adapter to the following settings:
• IP Address: 169.254.xxx.xxx
• Subnet Mask: 255.255.0.0
• Gateway: n/a
3. Go to the Command Prompt(on Windows) or Terminal (on
macOS) and enter the command arp –a. The Print Server’s
IP Address and MAC Address will appear. The MAC Address
will match the one on the bottom of the Print Server.
Note: The Print Server may take serveral minutes for it to
appear in the arp table.
4. Access the web interface by entering the IP address you got
from the previous step in the address bar of a web browser.
5. Set the print server to a static IP address within the subnet
your computer & networking equipment is on (For further
information, refer to the section Viewing/Configuring
Network Settings to change the Print Server’s IP Address).
6. Change the IP address for your network adapter back to its
original IP address.
7. Disconnect the CAT5e/6 Cable from the Computer and
connect it into a RJ45 Port on a Router or Network Device.
8. Add the printer using Operating System (OS) specific steps.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

13
Setting Up a Printer in Windows
1. Navigate to the Control Panel screen and select the Devices
and Printers icon.

Device and Printer Screen

2. Click the Add a Printer link at the top of the screen.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

14
 3. On the Add a Device screen, click on the The printer that I
want isn’t listed link.

Add a Device Screen

4. On the Add Printer screen, select Add a printer using a
TCP/IP address or hostname then click the Next button.

Add Printer Screen

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

15
 5. On the Hostname or IP address field enter the IP address
assigned to the print server, then click the Next button,
Windows will detect the TCP/IP port and move to the next
screen automatically.

Add Printer Screen

6. Set the Device Type field to Custom, then click Settings.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

16
 Add Printer Screen
7. On the Configure Standard TCP/IP Port Monitor screen, set
the Protocol to LPR.
8. Under LPR Settings, enter lp1 into the Queue Name field
then click OK.

Configue Standard TCP/IP Port Monitor Screen

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

17
 9. The Add Printer screen will appear, click the Next button.
10. Windows will attempt to automatically detect the printer
driver:
• If Windows fails to detect the proper printer driver: Select
your printer’s Manufacturer and Model from the Install
the Printer Driver screen that appears.
• If your printer model doesn’t appear in the list: Select
Windows Update (this update may take serveral minutes)
to update the list of printer models. When the update
is complete select for your printers Manufacturer and
Model from the Install the Printer Driver screen that
appears.
11. Windows will start to install the printer driver. Click the
Finish button when the installation is complete.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

18
Setting Up a Printer in macOS
1. From the System Preferences screen, click on the Printers &
Scanners icon.

System Preferences Screen

2. The Printers & Scanners screen will appear, click the + icon
on the left side of the screen.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

19
 Printers & Scanner Screen

3. The Add screen will appear, if the printer appears on the

Default tab, select it and click the Add button.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

20
 Add screen
4. If the printer does not appear, select the IP tab at the top of
the screen.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

21
 IP Screen
5. Enter the IP address of the Print Server in the Address field.
6. Set the Protocol to Line Printer Daemon – LPD and Queue
as lp1.
7. The wizard should automatically attempt to detect the driver
needed for the printer. When it has settled on one, click the
Add button.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

22
Performing a Hard Factory Reset
1. Insert the tip on a pen into the Recessed Reset button on
the side of the Print Server.
2. Gently press and hold the Recessed Reset button for 5
seconds to reset all settings back to factory defaults.

Software Operation
Accessing the Web Interface
1. Navigate to a web page and enter the Print Server’s IP
Address.
2. The Network Print Server screen will appear.
Changing the Screen Language
1. From any screen on the Network Print Server Web
Interface, click on the Select Language drop-down list.
2. Select the desired language from the drop-down menu.

Select Language Drop-Down

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

23
 3. The Menu will refresh with the selected language loaded.
Viewing Server Information/Device Information
1. From any screen on the Network Print Server Web
Interface, click on the Status Link.
2. The Status screen will appear.

Status Screen
3. The following information is available on the Status screen:
• Server Information
• Server Name: The name of the server
• Manufacturer: The name of the manufacturer of the
server
• Model: The server model
• Firmware Version: The latest firmware version number

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

24
 • Server UP-Time: The amount of time the server has been
operational.
• Web Page Version: The latest web page version number.
• Device Information
• Device Name: The name of the connected device
• Link Status: The link status of the connected device
(wether it is linked to the print server or not)
• Device Status: The status of the connected device.
• Current User: The user name of the user currently using
the device.
Viewing/Configuring Network Settings
1. From any screen on the Network Print Server Web
Interface, click on the Network Link.
2. The Network screen will appear.

Network Screen
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

25
 3. The following information is available on the Network In
formation section of the Network screen:
• IP Setting: Shows the Print Server’s current IP Setting,
either Fixed IP or Automatic (DHCP) depending on how
the print server was setup.
• IP Address: Shows the Print Server’s current IP Address.
• Subnet Mask: Shows the Print Server’s current Subnet
Mask.
• MAC Address: Shows the Print Server’s MAC Address.
4. The following fields on the Network Settings section of the
Network screen can be configured:
• DHCP Setting: Assigns a dynamic IP Address to the
connected device each time the device connects to a
network. Select either to Enable or Disable Dynamic Host
Configuration Protocol (DHCP).
• IP Address: If the DHCP field is Disable you can manually
enter an IP Address. If the DHCP field is Enable the IP
Address will be generated automatically.
• Subnet Mask: Allows you to enter a subnet mask.
• Server Name: Allows you to enter a server name.
• Password: Enter the user defined password in order to
apply changes to the Network Settings.
Note: If no password has been created a password is not
required to make changes to the Network Settings.
5. Click the Submit button to save any changed made to the
Network Settings.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

26
 6. Click the Clear button to clear a Password if one has been
entered in the Password field.
Restarting a Device
1. From any screen on the Network Print Server Web
Interface, click on the Restart Device Link.
2. The Restart Device screen will appear.

Restart Device Screen

3. Enter the user defined password in order to restart the
device.
Note: If no password has been created a password is not
required to restart the device.
4. Click the Submit button to restart the device.
5. Click the Clear button to clear a Password if one has been
entered in the Password field.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

27
Resetting the Device to Factory Settings
1. From any screen on the Network Print Server Web
Interface, click on the Factory Default Link.
2. The Factory Default screen will appear.

Factory Default Screen

3. Enter the user defined password in order to reset the device
to factory defaults.
Note: If no password has been created a password is not
required to reset the device to factory defaults.
4. Click the Submit button to reset the device to factory
defaults.
5. Click the Clear button to clear a Password if one has been
entered in the Password field.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

28
Creating/Changing a Password
1. From any screen on the Network Print Server Web
Interface, click on the Factory Default Link.
2. The Factory Default screen will appear.

Password Change Screen

3. Enter the user defined password in the Current Password
field. When creating a new password for the first time leave
the Current Password field blank.
4. Enter a new password in the New Password field. The
password can contain alphanumeric and special characters
and is 1 - 20 characters in length.
5. Re-enter the new password in the Confirm New Password
field.
6. Click the Submit button to create/reset the password.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

29
 7. Click the Clear button to clear a Password if one has been
entered in the Password field.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

30
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their officers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
profits, loss of business, or any pecuniary loss, arising out of or related to the use
of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

31
 Hard-to-find made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd. StarTech.com LLP StarTech.com Ltd.
45 Artisans Cres. 2500 Creekside Pkwy. Unit B, Pinnacle
London, Ontario Lockbourne, Ohio 15 Gowerton Rd.,
Brackmills
N5V 5E9 43137
Northampton
Canada U.S.A.
NN4 7BW
United Kingdom
FR: startech.com/fr ES: startech.com/es IT: startech.com/it
DE: startech.com/de NL: startech.com/nl JP: startech.com/jp

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support