SLOVENSKI STANDARD

SIST EN 10143:2006
01-september-2006

1DGRPHãþD
SIST EN 10143:1997

.RQWLQXLUQRYURþHSUHYOHþHQHSORþHYLQHLQWUDNRYL0HMQLRGVWRSNLPHULQ
WROHUDQFHREOLNH

Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape

Kontinuierlich schmelztauchveredeltes Blech und Band aus Stahl - Grenzabmaße und

Formtoleranzen
iTeh STANDARD PREVIEW
(standards.iteh.ai)
Tôles et bandes en acier revetues en continu par immersion a chaud - Tolérances sur
les dimensions et sur la forme
SIST EN 10143:2006
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
Ta slovenski standard je istoveten b2ada1e0f1f4/sist-en-10143-2006
z: EN 10143:2006

ICS:
77.140.50

SIST EN 10143:2006 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
 iTeh STANDARD PREVIEW
(standards.iteh.ai)
SIST EN 10143:2006
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
b2ada1e0f1f4/sist-en-10143-2006
EUROPEAN STANDARD EN 10143
NORME EUROPÉENNE
EUROPÄISCHE NORM June 2006

ICS 77.140.50 Supersedes EN 10143:1993

English Version

Continuously hot-dip coated steel sheet and strip - Tolerances

on dimensions and shape

Tôles et bandes en acier revêtues en continu par Kontinuierlich schmelztauchveredeltes Blech und Band aus
immersion à chaud - Tolérances sur les dimensions et sur Stahl - Grenzabmaße und Formtoleranzen
la forme

This European Standard was approved by CEN on 24 May 2006.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
iTeh STANDARD PREVIEW
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

(standards.iteh.ai)
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 10143:2006
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
b2ada1e0f1f4/sist-en-10143-2006

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36 B-1050 Brussels

© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10143:2006: E
worldwide for CEN national Members.
EN 10143:2006 (E)

Contents

Page
Foreword......................................................................................................................................................................3
1 Scope ..............................................................................................................................................................4
2 Normative references ....................................................................................................................................4
3 Terms and definitions ...................................................................................................................................4
4 Designation ....................................................................................................................................................4
5 Condition of delivery .....................................................................................................................................5
6 Tolerances on thickness...............................................................................................................................5
7 Tolerances on width ......................................................................................................................................9
7.1 General............................................................................................................................................................9
7.2 Sheet and wide strip of width ≥ 600 mm .....................................................................................................9
7.3 Slit wide strip of width less than 600 mm .................................................................................................10
8 iTeh STANDARD PREVIEW
Tolerances on length...................................................................................................................................11
9 (standards.iteh.ai)
Tolerances on flatness................................................................................................................................11
9.1 Steel grades with specified minimum Re or Rp0,2 < 360 MPa ...................................................................11
9.2
SIST EN 10143:2006
Steel grades with specified minimum Rp0,2 ≥ 360 MPa.............................................................................12
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
10 Tolerances on out-of-squareness ..............................................................................................................12
b2ada1e0f1f4/sist-en-10143-2006
11 Tolerances on edge camber .......................................................................................................................12
12 Superimposition of dimensions .................................................................................................................13
Bibliography ..............................................................................................................................................................14

2
 EN 10143:2006 (E)

Foreword
This document (EN 10143:2006) has been prepared by Technical Committee ECISS/TC 27 “Surface coated flat
products - Qualities, dimensions, tolerances and specific tests”, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest
by December 2006.

This document supersedes EN 10143:1993.

In comparison with EN 10143:1993 the following alterations were considered:

a) Leaded flat products in accordance with EURONORM 153 are no longer referred to.

b) Applicable product thickness exceeded to maximal 6,50 mm (with additional specification of 0,20mm minimum
thickness)

c) Applicable width ranges exceeded from three to four.

d) Thickness tolerances specified for four (instead of two) yield strength ranges.
iTeh STANDARD PREVIEW
e) (standards.iteh.ai)
Reduced thickness tolerances for products with (R or R ) < 360 MPa.
e p0,2

f) Altered thickness tolerances for products with Rp0,2 ≥ 360 MPa.

SIST EN 10143:2006
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
g) Flatness tolerances decreased.
b2ada1e0f1f4/sist-en-10143-2006
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.

3
EN 10143:2006 (E)

1 Scope
This European Standard applies to continuously zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-
zinc alloy (AZ) and aluminium-silicon alloy (AS) hot-dip coated flat products made of low carbon and high strength
steels for cold forming and of structural steels with a minimum thickness of 0,20 mm and a maximum thickness of
6,50 mm, delivered as sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. The
concerned standards are EN 10292, EN 10326, EN 10327 and hot-dip coated products according to prEN 10336.

It does not apply for

 hot-rolled sheet and strip without coating (see EN 10051) and

 uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131).

2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.

EN 10079:1992, Definition of steel products

3 Terms and definitions

iTeh STANDARD PREVIEW
(standards.iteh.ai)
For the purposes of this document, the terms and definitions for hot-dip coated flat products in accordance with EN
10079:1992 and the following apply. SIST EN 10143:2006
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
3.1 b2ada1e0f1f4/sist-en-10143-2006
nominal (specified) thickness
whole order thickness of the metallically coated product

NOTE Nominal thickness includes both substrate and coating.

4 Designation
4.1 Products conforming to this European Standard shall be designated in the following order
(see also Clause 5):

a) type of product (sheet, wide strip, slit wide strip or cut length);

b) the reference to this European Standard, i.e. EN 10143;

c) nominal thickness in mm;

d) the letter S for products ordered with special tolerances on thickness;

e) nominal width in mm;

f) the letter S for products ordered with special tolerances on width;

g) nominal length in mm (sheets and cut lengths only);

h) the letter S for products ordered with special tolerances on length (sheets and cut lengths only);

4
 EN 10143:2006 (E)

i) the letter FS for sheets or cut lengths ordered with special tolerances on flatness;

j) the letters CS for slit strip ordered with special tolerances on camber.

4.2 The product designation in accordance with 4.1 shall be followed by the complete designation of the steel
ordered (e.g. according to EN 10327).

Example 1 Strip, delivered with dimensional tolerances in accordance with EN 10143 with nominal thickness of 0,80 mm,
ordered with normal thickness tolerances, nominal width 1 200 mm, ordered with normal width tolerances,
ordered with normal flatness tolerances, made of steel DX53D+ZF (1.0355+ZF) in accordance with EN 10327, coating mass
100 g/m² (100), coating finish R, surface quality B, surface treatment oiled (O):

Strip EN 10143–0,80x1200–steel EN 10327 DX53D+ZF100–R–B–O

or:

Strip EN 10143–0,80x1200–steel EN 10327 1.0355+ZF100–R–B–O

Example 2 1 sheet, delivered with dimensional tolerances in accordance with EN 10143 with nominal thickness of 0,80 mm,
ordered with special thickness tolerances (S), nominal width 1 200 mm, ordered with special width tolerances (S), nominal
length 2 500 mm, ordered with special flatness tolerances (FS), made of steel HX300LAD +ZF (1.0932+ZF) in accordance with
EN 10292, coating mass 100 g/m² (100), coating finish R, surface quality B, surface treatment oiled (O):

1 sheet EN 10143–0,80Sx1200Sx2500FS–steel EN 10292 HX300LAD+ZF100–R–B–O

or: iTeh STANDARD PREVIEW

(standards.iteh.ai)
1 sheet EN 10143-0,80Sx1200Sx2500FS–steel EN 10292 1.0932+ZF100–R–B–O

SIST EN 10143:2006
5 Condition of delivery
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
b2ada1e0f1f4/sist-en-10143-2006
5.1 Flat products according to this European Standard may be delivered as follows:

a) with normal or special thickness tolerances (see Tables 1 to 4);

b) with normal or special width tolerances (see Tables 5 and 6);

c) with normal or special length tolerances for sheet or cut lengths (see Table 7);

d) with normal or special flatness tolerances for sheet or cut lengths (see Tables 8 and 9);

e) with normal or special tolerances on camber for slit strip of width less than 600 mm (see Clause 11).

5.2 In the absence of information on the order in respect of the condition of delivery given in 5.1, the flat products
shall be delivered with normal tolerances on thickness, width, length, flatness and camber.

6 Tolerances on thickness
6.1 The thickness may be measured at any point located more than 40 mm from the edges.

In the case of slit coils or cut lengths having a width ≤ 80 mm, the position of the measurement shall be at the
middle axis.

6.2 The tolerances on thickness shall be as given in Tables 1 to 4 and apply over the whole length. For coating
thicknesses corresponding to coating designations Z450 and Z600, the normal and special tolerances specified in
Tables 1 to 4 are increased by ± 0,01 mm apply.

5
EN 10143:2006 (E)

Tolerances closer than special tolerances may be agreed at the time of enquiry and order.

In the case of products for which no yield strength is specified, the tolerances specified in Table 2 for the grades
DX51D and S550GD and in Table 4 for all other grades apply, unless otherwise agreed at the time of enquiry and
order.

Table 1 — Tolerances for steel grades with specified

minimum yield strength Re or specified minimum proof strength Rp0,2 < 260 MPa

Dimensions in millimetres

Nominal thickness t Normal tolerances a Special tolerances (S) a

for a nominal width w for a nominal width w

≤ 1 200 b 1 200 < w ≤ 1 500 > 1 500 ≤ 1 200 b 1 200 < w ≤ 1 500 > 1 500

0,20 < t ≤ 0,40 ± 0,04 ± 0,05 ± 0,06 ± 0,030 ± 0,035 ± 0,040

0,40 < t ≤ 0,60 ± 0,04 ± 0,05 ± 0,06 ± 0,035 ± 0,040 ± 0,045

0,60 < t ≤ 0,80 ± 0,05 ± 0,06 ± 0,07 ± 0,040 ± 0,045 ± 0,050

0,80 < t ≤ 1,00 ± 0,06 ± 0,07 ± 0,08 ± 0,045 ± 0,050 ± 0,060

1,00 < t ≤ 1,20 ± 0,07 ± 0,08 ± 0,09 ± 0,050 ± 0,060 ± 0,070

1,20 < t ≤ 1,60 ± 0,10 ± 0,11 ± 0,12 ± 0,060 ± 0,070 ± 0,080

1,60 < t ≤ 2,00 ± 0,12 ± 0,13 ± 0,14 ± 0,070 ± 0,080 ± 0,090

2,00 < t ≤ 2,50

iTeh
± 0,14
STANDARD
± 0,15 ± 0,16
PREVIEW
± 0,090 ± 0,100 ± 0,110

2,50 < t ≤ 3,00 ± 0,17

(standards.iteh.ai)
± 0,17 ± 0,18 ± 0,110 ± 0,120 ± 0,130

3,00 < t ≤ 5,00 ± 0,20 ± 0,20SIST EN 10143:2006

± 0,21 ± 0,15 ± 0,16 ± 0,17

5,00 < t ≤ 6,50

https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
± 0,22 ± 0,22 ± 0,23 ± 0,17 ± 0,18 ± 0,19
b2ada1e0f1f4/sist-en-10143-2006
a The thickness tolerances in the region of coil welds may be increased by a maximum of 50 % over a length of 10 m. This
increase is applicable to all thicknesses and, unless otherwise agreed at the time of enquiry and order, to normal and special
(negative and positive) tolerances. For thicker coatings, see 6.2.
b Wide strip: width ≥ 600 mm; slit wide strip: rolling width ≥ 600 mm, slit to width less than 600 mm.

6
 EN 10143:2006 (E)

Table 2 — Tolerances for steel grades with specified minimum proof strength
260 MPa ≤ Rp0,2 < 360 MPa and for grades DX51D and S550GD

Dimensions in millimetres

Nominal thickness t Normal tolerances a Special tolerances (S) a

for a nominal width w for a nominal width w

≤ 1 200 b 1 200 < w ≤ 1 500 > 1 500 ≤ 1 200 b 1 200 < w ≤ 1 500 > 1 500

0,20 < t ≤ 0,40 ± 0,05 ± 0,06 ± 0,07 ± 0,035 ± 0,040 ± 0,045

0,40 < t ≤ 0,60 ± 0,05 ± 0,06 ± 0,07 ± 0,040 ± 0,045 ± 0,050

0,60 < t ≤ 0,80 ± 0,06 ± 0,07 ± 0,08 ± 0,045 ± 0,050 ± 0,060

0,80 < t ≤ 1,00 ± 0,07 ± 0,08 ± 0,09 ± 0,050 ± 0,060 ± 0,070

1,00 < t ≤ 1,20 ± 0,08 ± 0,09 ± 0,11 ± 0,060 ± 0,070 ± 0,080

1,20 < t ≤ 1,60 ± 0,11 ± 0,13 ± 0,14 ± 0,070 ± 0,080 ± 0,090

1,60 < t ≤ 2,00 ± 0,14 ± 0,15 ± 0,16 ± 0,080 ± 0,090 ± 0,110

2,00 < t ≤ 2,50 ± 0,16 ± 0,17 ± 0,18 ± 0,110 ± 0,120 ± 0,130

2,50 < t ≤ 3,00 ± 0,19 ± 0,20 ± 0,20 ± 0,130 ± 0,140 ± 0,150

3,00 < t ≤ 5,00 ± 0,22 ± 0,24 ± 0,25 ± 0,17 ± 0,18 ± 0,19

5,00 < t ≤ 6,50 ± 0,24 ± 0,25 ± 0,26 ± 0,19 ± 0,20 ± 0,21

iTeh STANDARD PREVIEW
a The thickness tolerances in the region of coil welds may be increased by a maximum of 50 % over a length of 10 m. This
(standards.iteh.ai)
increase is applicable to all thicknesses and, unless otherwise agreed at the time of enquiry and order, to normal and special
(negative and positive) tolerances. For thicker coatings, see 6.2.
b SIST EN 10143:2006
Wide strip: width ≥ 600 mm; slit wide strip: rolling width ≥ 600 mm, slit to width less than 600 mm.
https://standards.iteh.ai/catalog/standards/sist/bbab40bd-4cd7-424b-a877-
b2ada1e0f1f4/sist-en-10143-2006