LOAD CHARTS

RT765E-2

METRIC
85% STABILITY

232673
SERIAL NUMBER

RT765E-2 - S/N 232673 1

RT765E-2 - S/N 232673 2
 TABLE OF CONTENTS

GENERAL NOTES ................................................................................................ 4

WEIGHT REDUCTIONS / LINE PULLS & REEVING INFO / RIGGING CHART FOR
INSTL. & REMOVAL OF HYDRAULIC REMOVABLE COUNTERWEIGHT.......... 5
LIFTING AREA DIAGRAMS .................................................................................. 6
RANGE DIAGRAM WITH FOLDING EXTENSION ............................................... 7
RANGE DIAGRAM WITH FOLDING EXTENSION + 6.1 m INSERT ................... 8
RANGE DIAGRAM WITH FOLDING EXTENSION + 12.2 m INSERT ................. 9

ON OUTRIGGERS FULLY EXTENDED

MAIN BOOM .................................................................................................. 10
FOLDING EXTENSION ................................................................................. 11
FOLDING EXTENSION + 6.1 m INSERT ...................................................... 12
FOLDING EXTENSION + 12.2 m INSERT .................................................... 13

ON OUTRIGGERS 50% EXTENDED

MAIN BOOM .................................................................................................. 14
FOLDING EXTENSION ................................................................................. 15
FOLDING EXTENSION + 6.1 m INSERT ...................................................... 16
FOLDING EXTENSION + 12.2 m INSERT .................................................. N/A

ON OUTRIGGERS 0% EXTENDED
MAIN BOOM .................................................................................................. 17

ON RUBBER .................................................................................................18-19

TIRE INFLATION................................................................................................. 20

RT765E-2 - S/N 232673 3

 NOTES TO LIFTING CAPACITIES

GENERAL:
1. Rated loads as shown on lift chart pertain to this machine as originally manufactured and equipped. Modifications to the machine or use
of optional equipment other than that specified can result in a reduction of capacity.
2. Construction equipment can be hazardous if improperly operated or maintained. Operation and maintenance of this machine shall be in
compliance with the information in the Operator’s and Safety Handbook, Service Manual, and Parts Manual supplied with this machine. If
these manuals are missing, order replacements from the manufacturer through the distributor.
3. The operator and other personnel associated with machine shall fully acquaint themselves with the latest National Safety Standards for
cranes.
SETUP:
1. The machine shall be level and on a firm supporting surface. Depending on the nature of the supporting surface, it may be necessary to
have structural supports under the outrigger floats or tires to spread the load to a larger bearing surface.
2. For outrigger operation, all outriggers shall be properly extended with tires raised free of crane weight before operating the boom or lifting
loads.
3. When machine is equipped with center front stabilizer, the front stabilizer shall be set in accordance with instructions in Operator's &
Safety Handbook.
4. When equipped with removable and/or extendible counterweight, the proper counterweight shall be installed and fully extended before
and during operation.
5. Tires shall be inflated to the recommended pressure before lifting on rubber.
6. With certain boom and hoist tackle combinations, maximum capacities may not be obtainable with standard cable lengths.
7. Unless approved by the crane manufacturer, do not travel with boom extension or jib erected. Refer to Operator's and Safety Handbook
for job-site travel information.
OPERATION:
1. Rated loads at rated radius shall not be exceeded. Do not attempt to tip the machine to determine allowable loads. For clamshell,
magnet, grapple or concrete bucket operation, weight of component and load must not exceed 80% of rated lifting capacities.
2. All rated loads have been tested to and meet the requirements of SAE J1063 - Cantilevered Boom Crane Structures - Method of Test, and
do not exceed 85% of the tipping load on outriggers fully extended. Capacities on outriggers 50% extended and 0% extended (fully
retracted) correspond to SAE J1289 (Test Load = 1.25P + 0.1A). 0.1A represents one-tenth (0.10) of the total boom weight reduced to the
boom point. Loads are also determined by SAE J765 Crane Stability Test Code.
3. Rated loads include the weight of hookblock, slings and auxiliary lifting devices and their weights shall be subtracted from the listed rating
to obtain the net load to be lifted. When more than the minimum required parts of line needed to pick the load are used, the additional rope
weight as measured from the lower sheaves of the main boom shall be considered part of the load to be lifted. When both the hook block
and headache ball are reeved, the lifting device that is NOT in use, including the line as measured from the lower sheave(s) of the nose
supporting the unused device shall be considered part of the load.
4. Load ratings are based on freely suspended loads. No attempt shall be made to move a load horizontally on the ground in any direction.
5. The maximum in-service wind speed is 32 km/h. It is recommended when wind velocity is above 32 km/h, rated loads and boom lengths
shall be appropriately reduced. For machines not in-service, the main boom should be retracted and lowered with swing brake set in wind
velocities over 48 km/h.
6. Rated loads are for lift crane service only.
7. Do not operate at a radius or boom length where capacities are not listed. At these positions, the machine may overturn without any load
on the hook.
8. The maximum load which can be telescoped is not definable because of variations in loadings and crane maintenance, but it is safe to
attempt retraction and extension of the boom within the limits of the capacity chart.
9. When the boom length or lift radius or both are between values listed, the smallest load shown at either the next larger radius or next
longer or shorter boom length shall be used.
10. For safe operation, the user shall make due allowances for his particular job conditions, such as: soft or uneven ground, out of level
conditions, high winds, side loads, pendulum action, jerking or sudden stopping of loads, experience of personnel, two machine (tandem)
lifts, traveling with loads, electric wires, obstacles, hazardous conditions, etc. Side pull on boom or jib is extremely dangerous.
11. Regardless of counterweight and outrigger spread configuration, no deduct is required from the main boom charts for a stowed boom
extension.
12. Never handle personnel with this machine unless the requirements of the applicable national, state, and local regulations and safety
codes are met.
13. Keep load handling devices a minimum of 107 cm below boom head at all times.
14. The boom angle before loading should be greater than the loaded boom angle to account for deflection.
15. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation.
16. Capacities for the 10.9 m boom length shall be lifted with boom fully retracted. If boom is not fully retracted, capacities shall not exceed
those shown for the 12.2 m boom length.
17. When operating in the "On Outriggers 50% Extended (5.3 m spread)" mode, the outrigger beam pins must be engaged. When operating
in the "On Outriggers 0% Extended (3.2 m spread)" mode, the outrigger beams must be fully retracted. Failure to follow these precautions
could result in structural damage or loss of stability of the machine.
18. Do not lift loads when boom is fully lowered. The Load Moment Indicator (LMI) senses pressure and will not provide warnings or lockout.
The crane can become overloaded if lift cylinder(s) is fully retracted.
19. WARNING: Lifting with the 10.1 m extension base, with the 7.0 m extension fly either erected or folded along side of extension base, is
strictly prohibited.
20. The maximum outrigger pad load is 41,730 kg.
DEFINITIONS:
1. Operating Radius: Horizontal distance from a projection of the axis of rotation to the supporting surface before loading to the center of the
vertical hoist line or tackle with load applied.
2. Loaded Boom Angle (Shown in Parenthesis on Main Boom Capacity Chart): is the angle between the boom base section and the
horizontal, after lifting the rated load at the rated radius with the rated boom length.
3. Working Area: Areas measured in a circular arc about the center line of rotation as shown on the working area diagram.
4. Freely Suspended Load: Load hanging free with no direct external force applied except by the lift cable.
5. Side Load: Horizontal force applied to the lifted load either on the ground or in the air.

RT765E-2 - S/N 232673 4

 WEIGHT REDUCTIONS FOR LOAD
HANDLING DEVICES RIGGING CHART
10.1 - 17.1 m INSTALLATION AND REMOVAL OF
FOLDING BOOM EXTENSION
HYDRAULIC REMOVABLE CWT
Without With 161 kg
block or overhaul ON O/R'S FULLY EXTENDED - 360°
ball ball
#0801
*10.1 m Extension (erected) - 1746 kg 2713 kg Radius
Main Boom Length
*17.1 m Extension (erected) - 3910 kg 5520 kg in
in Meters
Meters
FOLDING EXT. WITH 6.1 m INSERT *10.9 12.2
*10.1 m Extension (erected) - 3393 kg 4704 kg 9,300 9,300
3
*17.1 m Extension (erected) - 6042 kg 8047 kg (69.5) (72)
FOLDING EXT. WITH 12.2 m INSERT 9,300 9,300
3.5
*10.1 m Extension (erected) - 4531 kg 5606 kg
(66.5) (69.5)
*17.1 m Extension (erected) - 6627 kg 8042 kg 9,300 9,300
4
(63.5) (66.5)
*Reduction of main boom capacities
(no deduct required for stowed boom extension) 9,300 9,300
4.5
(60.5) (64)
AUXILIARY BOOM NOSE 59 kg 9,300 9,300
5
HOOKBLOCKS and HEADACHE BALLS: (57.5) (61.5)
60 t, 5 sheave 581 kg+ 9,300 9,300
6
7.5 t overhaul ball 161 kg+ (50.5) (55.5)
+Refer to rating plate for actual weight. 9,300 9,300
7
(42.5) (49)
When lifting over swingaway and/or jib combinations, deduct total
weight of all load handling devices reeved over main boom nose 9,300 9,300
8
directly from swingaway or jib capacity. (32.5) (42)
9,300 9,300
NOTE: All load handling devices and boom attachments are 9
(16.5) (33.5)
considered part of the load and suitable allowances MUST BE
MADE for their combined weights. Weights are for Grove fur- 9,300
10
nished equipment. (20.5)
NOTE: ( ) Boom angles are in degrees.
HOIST PERFORMANCE #LMI operating code. Refer to LMI manual for
operating instructions.
Hoist Line Pulls Drum Rope
Wire Main Boom Length
Two Speed Hoist Capacity (m) Boom in Meters
Rope Angle
Low High *10.9 12.2
Layer Layer Total
Available kg* Available kg* 9,300 9,300
0°
1 8,225 4,113 31 31 (9.2) (10.4)
80040297
2 7,560 3,780 33 64 NOTE: ( ) Reference radii in meters.
3 6,994 3,497 37 101 *Boom must be fully retracted.

4 6,508 3,254 39 140

5 6,084 3,042 43 183
6 5,713 2,856 45 228
*Max. lifting capacity: 6x37 and 35x7 class = 7,620 kg
LINE PULLS AND REEVING INFORMATION
PERMISSIBLE NOMINAL
HOISTS CABLE SPECS.
LINE PULLS CABLE LENGTH

19 mm (3/4") 6x37 Class

Main EIPS, IWRC Special Flexible 7,620 kg 152 m
Min. Breaking Str. 26 670 kg
19 mm (3/4") 35x7 Class
Main & Aux. Rotation Resistant (non-rotating) 7,620 kg 152 m
Min. Breaking Strength 38 920 kg
The approximate weight of 19 mm wire rope is 2.2 kg/m
RT765E-2 - S/N 232673 5
RT765E-2 - S/N 232673 6
 9

RT765E-2 - S/N 232673 7

 9

RT765E-2 - S/N 232673 8

 9

RT765E-2 - S/N 232673 9

 RATED LIFTING CAPACITIES IN KILOGRAMS
10.9 m - 33.5 m BOOM
ON OUTRIGGERS FULLY EXTENDED - 360°
Radius #0001
in Main Boom Length in Meters
Meters
10.9 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
60,000 40,950 40,950
3
(69.5) (72) (76)
53,000 40,950 40,950 28,350
3.5
(66.5) (69.5) (74) (78)
47,450 40,950 40,950 28,350 *18,225
4
(63.5) (66.5) (72) (75.5) (78)
42,875 40,950 40,950 28,350 18,225
4.5
(60.5) (64) (70) (73.5) (76)
39,050 39,025 38,300 28,350 18,225 *18,225
5
(57.5) (61.5) (67.5) (72) (75) (78)
32,950 32,925 32,825 28,350 18,225 18,225 *18,225
6
(50.5) (55.5) (63.5) (68.5) (72) (74.5) (78)
28,325 28,300 28,225 26,250 18,225 18,225 18,225 *16,725 *11,400
7
(42.5) (49) (59) (65) (69) (72) (74.5) (78) (78)
24,150 24,150 23,975 23,275 18,225 18,225 16,575 15,250 11,400
8
(32.5) (42) (54.5) (61.5) (66) (69.5) (72) (74.5) (76)
20,600 20,550 20,375 20,250 18,225 16,575 15,050 13,875 11,400
9
(16.5) (33.5) (49.5) (58) (63) (67) (70) (72.5) (74.5)
17,200 17,300 17,275 17,325 15,125 13,725 12,700 11,400
10
(20.5) (44) (54) (60) (64.5) (67.5) (70.5) (72.5)
12,075 12,225 12,575 12,775 11,600 10,725 10,050
12
(30) (45.5) (53.5) (59) (63) (66.5) (69)
9,000 9,360 9,730 9,955 9,205 8,620
14
(35) (46) (53.5) (58.5) (62) (65)
6,755 7,165 7,545 7,920 7,980 7,470
16
(19) (37.5) (47) (53) (57.5) (61.5)
5,555 5,960 6,340 6,525 6,530
18
(26) (39.5) (47.5) (53) (57.5)
4,755 5,145 5,320 5,495
20
(30.5) (41) (48) (53)
3,790 4,210 4,380 4,545
22
(16.5) (33.5) (42.5) (48.5)
3,435 3,620 3,780
24
(23.5) (36) (43.5)
2,975 3,150
26
(28) (37.5)
2,400 2,620
28
(16) (31)
2,135
30
(22)
Minimum boom angle (°) for indicated length (no load) 0
Maximum boom length (m) at 0° boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
Boom Main Boom Length in Meters
Angle 10.9 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
13,775 11,675 8,145 5,930 4,565 3,535 2,860 2,220 1,770
0°
(9.2) (10.4) (13.5) (16.6) (19.6) (22.6) (25.7) (28.7) (31.8)
NOTE: ( ) Reference radii in meters. 80039615
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
RT765E-2 - S/N 232673 10
 10.1 m - 17.1 m FOLDING BOOM EXTENSION
ON OUTRIGGERS FULLY EXTENDED - 360°

10.1 LENGTH 17.1 m LENGTH 1. All capacities above the bold line are
Radius
0° 25° 45° 0° 25° 45° based on structural strength of boom
in
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET extension .
Meters
#0021 #0022 #0023 #0041 #0042 #0043
*5,850 2. 10.1 m and 17.1 m folding boom exten-
9
(78) sion lengths may be used for single line
10
5,860 *3,775 lifting service only.
(77.5) (78)

12
5,860 *4,920 3,775 3. For main boom lengths less than 33.5 m
(74.5) (78) (77.5) with the boom extension erected, the
5,855 4,700 *3,360 3,775 rated loads are determined by boom
14
(72) (76.5) (78) (75.5)
angle. Use only the column which cor-
5,260 4,355 3,215 3,760 *2,400
16 responds to the boom extension length
(69) (73.5) (76.5) (73) (78)
4,665 3,935 3,100 3,480 2,345 and offset for which the machine is set
18
(66) (70.5) (73.5) (70.5) (77.5) up. For boom angles not shown, use
4,100 3,565 3,005 3,225 2,310 *1,750 rating of the next lower boom angle.
20
(63) (67.5) (70) (68) (75) (78)

22
3,710 3,250 2,920 2,990 2,250 1,690 4. WARNING: Operation of this machine
(60) (64.5) (67) (65.5) (72.5) (76.5) with heavier loads than the capacities
3,345 2,980 2,800 2,690 2,090 1,620
24
(56.5) (61) (63.5) (63) (70) (73.5)
listed is strictly prohibited. Machine tip-
3,015 2,740 2,610 2,425 2,020 1,560
ping with boom extension occurs rap-
26 idly and without advance warning.
(53.5) (58) (60) (60.5) (67) (71)
2,705 2,540 2,435 2,195 1,920 1,525
28 5. Boom angle is the angle above or below
(50) (54) (56.5) (57.5) (64.5) (68)
2,410 2,355 2,280 2,000 1,770 1,480 horizontal of the longitudinal axis of the
30
(46.5) (50.5) (52.5) (55) (61.5) (65) boom base section after lifting rated
32
2,110 2,155 2,105 1,830 1,640 1,460 load.
(42.5) (46.5) (48) (52) (58.5) (61.5)

34
1,770 1,955 1,675 1,520 1,425 6. Capacities listed are with outriggers prop-
(38.5) (42) (49) (55) (58) erly extended and vertical jacks set only.
1,470 1,630 1,540 1,410 1,350
36
(33.5) (36.5) (46) (51.5) (54) 7. When lifting over the main boom nose
1,205 1,340 1,400 1,315 1,270 with 10.1 m or 17.1 m extension erected,
38
(27.5) (30.5) (42.5) (48) (50)
the outriggers must be fully extended
970 1,215 1,220
40
(20) (38.5) (44) or 50% extended (5.3 m spread).
1,000 1,140
42
(34.5) (39.5)
800 945
44
(29.5) (34)
Min. boom angle (°)
for indicated length 19 29 47 23 32 49
(no load)
Max. boom length
(m) at 0° boom angle 30.5 27.4
(no load)
NOTE: ( ) Boom angles are in degrees. 80039618
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.

RT765E-2 - S/N 232673 11

 10.1 m - 17.1 m FOLDING BOOM EXTENSION + 6.1 m INSERT
ON OUTRIGGERS FULLY EXTENDED - 360°
17.1 m LENGTH 1. All capacities above the bold line are
Radius
0° 25° 45°
based on structural strength of boom
in extension.
OFFSET OFFSET OFFSET
Meters
#0084 #0085 #0086 2. The 17.1 m folding boom extension
2,830 length may be used for single line lift-
14
(78) ing service only.
2,715
16 3. For main boom lengths less than 33.5
(75.5)
m with the boom extension erected, the
2,710 rated loads are determined by boom
18
(73.5)
angle. Use only the column which cor-
2,470 2,170 responds to the boom extension length
20
(71.5) (78) and offset for which the machine is set
2,180 1,935 *1,705 up. For boom angles not shown, use
22
(69) (75.5) (78) rating of the next lower boom angle.
1,935 1,775 1,600
24 4. WARNING: Operation of this machine
(67) (73) (77)
with heavier loads than the capacities
1,725 1,610 1,470
26 listed is strictly prohibited. Machine tip-
(64.5) (71) (74.5)
ping with boom extension occurs rap-
1,545 1,460 1,310
28 idly and without advance warning.
(62) (68.5) (72)
1,385 1,330 1,190 5. Boom angle is the angle above or be-
30
(60) (66) (69) low horizontal of the longitudinal axis
1,260 1,215 1,115 of the boom base section after lifting
32 rated load.
(57.5) (63.5) (66.5)
1,120 1,095 1,040 6. Capacities listed are with outriggers
34
(55) (61) (63.5) properly extended and vertical jacks
1,015 995 955 set only.
36
(52.5) (58) (61)
910 905 870 7. When lifting over the main boom nose
38 with the 17.1 m extension erected and
(49.5) (55) (57.5)
6.1 m insert, the outriggers must be
825 825 805
40 fully extended or 50% extended (5.3
(47) (52) (54.5)
m spread).
750 755 705
42
(44) (49) (51)
695
44
(45.5)
545
46
(42)
Minimum boom angle
(°) for indicated length 42 41 50
(no load)
Maximum boom length
(m) at 0° boom angle 21.3
(no load)
80039620A
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
*This capacity is based upon maximum boom angle.

RT765E-2 - S/N 232673 12

 10.1 m - 17.1 m FOLDING BOOM EXTENSION + 12.2 m INSERT
ON OUTRIGGERS FULLY EXTENDED - 360°

17.1 m LENGTH 1. All capacities above the bold line are based
Radius
0° 25° 45° on structural strength of boom extension
in
OFFSET OFFSET OFFSET 2. 10.1 m and 17.1 m folding boom extension
Meters
#0084 #0085 #0086 lengths may be used for single line lifting ser-
1,975 vice only.
16
(78) 3. For main boom lengths less than 33.5 m with
1,795 the boom extension erected, the rated loads
18
(76) are determined by boom angle. Use only the
1,665 column which corresponds to the boom ex-
20 tension length and offset for which the ma-
(74)
1,505 1,625 chine is set up. For boom angles not shown,
22 use rating of the next lower boom angle.
(72) (78)
1,325 1,445 4. WARNING: Operation of this machine with
24
(70) (75.5) heavier loads than the capacities listed is
1,135 1,270 1,230 strictly prohibited. Machine tipping with boom
26 extension occurs rapidly and without advance
(68) (73.5) (77.5)
1,000 1,135 1,115 warning.
28
(66) (71.5) (75) 5. Boom angle is the angle above or below hori-
855 995 995 zontal of the longitudinal axis of the boom
30
(63.5) (69) (72.5) base section after lifting rated load.
740 875 880 6. Capacities listed are with outriggers properly
32
(61.5) (67) (70.5) extended and vertical jacks set only.
625 755 760
34 7. When lifting over the main boom nose with
(59.5) (65) (68)
17.1 m extension erected and 12.2 m insert,
530 640 675
36 the outriggers must be fully extended.
(57) (62.5) (65.5)
565 575
38
(60) (62.5)
505
40
(60)
Minimum boom angle
(°) for indicated length 55 57 59
(no load)
Maximum boom length
(m) at 0° boom angle 12.2
(no load)
80039622A
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
*This capacity is based upon maximum boom angle.

RT765E-2 - S/N 232673 13

 RATED LIFTING CAPACITIES IN KILOGRAMS
10.9 m - 33.5 m BOOM
ON OUTRIGGERS 50% EXTENDED (5.3 m spread) - 360°
Radius #4001
in Main Boom Length in Meters
Meters
10.9 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
56,100 40,950 40,950
3
(69.5) (72) (76)
50,750 40,950 40,950 28,350
3.5
(66.5) (69.5) (74) (78)
46,250 40,950 40,950 28,350 *18,225
4
(63.5) (66.5) (72) (75.5) (78)
42,450 40,950 40,950 28,350 18,225
4.5
(60.5) (64) (70) (73.5) (76)
39,025 37,750 34,900 28,350 18,225 *18,225
5
(57.5) (61.5) (67.5) (72) (75) (78)
28,025 27,725 25,850 24,300 18,225 18,225 *18,225
6
(50.5) (55.5) (63.5) (68.5) (72) (74.5) (78)
20,300 20,400 20,200 19,050 18,225 18,225 18,225 *16,725 *11,400
7
(42.5) (49) (59) (65) (69) (72) (74.5) (78) (78)
15,400 15,525 15,675 15,425 15,400 15,300 15,125 14,925 11,400
8
(32.5) (42) (54.5) (61.5) (66) (69.5) (72) (74.5) (76)
12,050 12,200 12,425 12,475 12,775 12,825 12,750 12,650 11,400
9
(16.5) (33.5) (49.5) (58) (63) (67) (70) (72.5) (74.5)
9,755 10,000 10,125 10,450 10,750 10,925 10,875 10,775
10
(20.5) (44) (54) (60) (64.5) (67.5) (70.5) (72.5)
6,705 6,915 7,280 7,615 7,940 8,155 8,260
12
(30) (45.5) (53.5) (59) (63) (66.5) (69)
4,790 5,195 5,570 5,910 6,110 6,305
14
(35) (46) (53.5) (58.5) (62) (65)
3,295 3,710 4,115 4,485 4,675 4,855
16
(19) (37.5) (47) (53) (57.5) (61.5)
2,610 3,025 3,415 3,610 3,785
18
(26) (39.5) (47.5) (53) (57.5)
2,180 2,580 2,780 2,960
20
(30.5) (41) (48) (53)
1,515 1,915 2,110 2,295
22
(16.5) (33.5) (42.5) (48.5)
1,375 1,565 1,745
24
(23.5) (36) (43.5)
1,115 1,290
26
(28) (37.5)
730 905
28
(16) (31)
580
30
(22)
Minimum boom angle (°) for indicated length (no load) 0
Maximum boom length (m) at 0° boom angle (no load) 33.5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
Boom Main Boom Length in Meters
Angle 10.9 12.2 15.2 **18.4 21.3 24.4 27.4 30.5
11,575 8,915 5,050 2,910 1,930 1,335 995 610
0°
(9.2) (10.4) (13.5) (16.6) (19.6) (22.6) (25.7) (28.7)
NOTE: ( ) Reference radii in meters. 80039616
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
RT765E-2 - S/N 232673 14
 10.1 m - 17.1 m FOLDING BOOM EXTENSION

ON OUTRIGGERS 50% EXTENDED (5.3 m spread) - 360°

10.1 m LENGTH 17.1 m LENGTH 1. All capacities above the bold line are
Radius
0° 25° 45° 0° 25° 45° based on structural strength of
in boom extension.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
Meters
#4021 #4022 #4023 #4041 #4042 #4043
2. 10.1 m and 17.1 m folding boom ex-
*5,860 tension lengths may be used for
9
(78)
single line lifting service only.
5,860 *3,775
10
(77.5) (78) 3. For main boom lengths less than
12
5,860 *4,920 3,775 33.5 m with the boom extension
(74.5) (78) (77.5) erected, the rated loads are deter-
5,855 4,700 *3,360 3,775 mined by boom angle. Use only the
14
(72) (76.5) (78) (75.5)
column which corresponds to the
5,120 4,355 3,215 3,760 *2,400 boom extension length and offset
16
(69) (73.5) (76.5) (73) (78)
for which the machine is set up. For
4,115 3,935 3,100 3,480 2,345
18 boom angles not shown, use rating
(66) (70.5) (73.5) (70.5) (77.5)
of the next lower boom angle.
3.285 3,565 3,005 3,225 2,310 *1,750
20
(63) (67.5) (70) (68) (75) (78) 4. WARNING: Operation of this ma-
2,630 3,050 2,920 2,840 2,250 1,690 chine with heavier loads than the
22
(60) (64.5) (67) (65.5) (72.5) (76.5)
capacities listed is strictly prohib-
2,095 2,460 2,660 2,300 2,090 1,620 ited. Machine tipping with boom ex-
24
(56.5) (61) (63.5) (63) (70) (73.5)
tension occurs rapidly and without
1,655 1,965 2,135 1,850 2,020 1,560
26
(53.5) (58) (60) (60.5) (67) (71)
advance warning.
1,280 1,550 1,690 1,470 1,920 1,525 5. Boom angle is the angle above or
28
(50) (54) (56.5) (57.5) (64.5) (68) below horizontal of the longitudinal
960 1,190 1,305 1,150 1,605 1,480 axis of the boom base section after
30
(46.5) (50.5) (52.5) (55) (61.5) (65)
lifting rated load.
685 885 965 875 1,265 1,460
32
(42.5) (46.5) (48) (52) (58.5) (61.5) 6. Capacities listed are with outriggers
615 635 970 1,175 properly extended and vertical jacks
34
(42) (49) (55) (58) set only.
710 880
36
(51.5) (54) 7. When lifting over the main boom
620 nose with 10.1 m or 17.1 m exten-
38
(50) sion erected, the outriggers must be
Min. boom angle (°) fully extended or 50% extended (5.3
for indicated length 36 35 47 45 45 49 m spread).
(no load)
Max. boom length
(m) at 0° boom angle 27.4 21.3
(no load)
NOTE: ( ) Boom angles are in degrees. 80039619
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.

RT765E-2 - S/N 232673 15

 10.1 m - 17.1 m FOLDING BOOM EXTENSION + 6.1 m INSERT
ON OUTRIGGERS 50% EXTENDED (5.3 m spread) - 360°

17.1 m LENGTH 1. All capacities above the bold line are

Radius based on structural strength of boom
0° 25° 45°
in extension
OFFSET OFFSET OFFSET
Meters
#4084 #4085 #4086 2. The 17.1 m folding boom extension
length may be used for single line lift-
2,830 ing service only.
14
(78)
2,715 3. For main boom lengths less than 33.5 m
16 with the boom extension erected, the
(75.5)
rated loads are determined by boom
2,710 angle. Use only the column which cor-
18
(73.5) responds to the boom extension length
2,470 2,170 and offset for which the machine is set
20
(71.5) (78) up. For boom angles not shown, use
2,180 1,935 *1,705 rating of the next lower boom angle.
22
(69) (75.5) (78) 4. WARNING: Operation of this machine
1,935 1,775 1,600 with heavier loads than the capacities
24
(67) (73) (77) listed is strictly prohibited. Machine tip-
1,725 1,610 1,470 ping with boom extension occurs rap-
26 idly and without advance warning.
(64.5) (71) (74.5)
1,480 1,460 1,310 5. Boom angle is the angle above or below
28
(62) (68.5) (72) horizontal of the longitudinal axis of the
1,155 1,330 1,190 boom base section after lifting rated
30 load.
(60) (66) (69)
875 1,215 1,115 6. Capacities listed are with outriggers prop-
32
(57.5) (63.5) (66.5) erly extended and vertical jacks set only.
630 1,025 1,040 7. When lifting over the main boom nose
34
(55) (61) (63.5) with the 17.1 m extension erected and
770 955 6.1 m insert, the outriggers must be fully
36 extended or 50% extended (5.3 m
(58) (61)
spread).
545 705
38
(55) (57.5)
Minimum boom angle
(°) for indicated length 52 53 53
(no load)
Maximum boom length
(m) at 0° boom angle 12.2
(no load)
80039621A
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
*This capacity is based upon maximum boom angle.

RT765E-2 - S/N 232673 16

 RATED LIFTING CAPACITIES IN KILOGRAMS
10.9 m - 33.5 m BOOM
ON OUTRIGGERS 0% EXTENDED (3.2 m spread) - 360°
Radius #8001
in Main Boom Length in Meters
Meters
10.9 12.2 15.2 **18.4 21.3 24.4 27.4 30.5 33.5
39,600 37,925 34,425
3
(69.5) (72) (76)
31,450 30,250 27,725 25,600
3.5
(66.5) (69.5) (74) (78)
25,850 24,950 23,000 21,350 *18,225
4
(63.5) (66.5) (72) (75.5) (78)
21,675 21,050 19,475 18,175 17,800
4.5
(60.5) (64) (70) (73.5) (76)
18,525 18,025 16,775 15,675 15,475 *15,175
5
(57.5) (61.5) (67.5) (72) (75) (78)
13,125 13,275 12,825 12,025 12,025 11,925 *11,750
6
(50.5) (55.5) (63.5) (68.5) (72) (74.5) (78)
9,740 9,865 10,050 9,510 9,605 9,610 9,555 *9,465 *9,340
7
(42.5) (49) (59) (65) (69) (72) (74.5) (78) (78)
7,395 7,515 7,725 7,605 7,810 7,885 7,890 7,865 7,800
8
(32.5) (42) (54.5) (61.5) (66) (69.5) (72) (74.5) (76)
5,675 5,790 5,985 6,130 6,405 6,545 6,595 6,615 6,590
9
(16.5) (33.5) (49.5) (58) (63) (67) (70) (72.5) (74.5)
4,475 4,660 4,795 5,130 5,425 5,560 5,610 5,615
10
(20.5) (44) (54) (60) (64.5) (67.5) (70.5) (72.5)
2,765 2,880 3,240 3,590 3,915 4,090 4,135
12
(30) (45.5) (53.5) (59) (63) (66.5) (69)
1,585 1,960 2,325 2,675 2,875 3,050
14
(35) (46) (53.5) (58.5) (62) (65)
645 1,035 1,410 1,770 1,970 2,160
16
(19) (37.5) (47) (53) (57.5) (61.5)
715 1,085 1,280 1,465
18
(39.5) (47.5) (53) (57.5)
550 740 925
20
(41) (48) (53)
Minimum boom angle (°) for indicated
length (no load)
0 24 32 36 40 43
Maximum boom length (m) at 0° boom
angle (no load)
18.4
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based on maximum boom angle.
Lifting Capacities at Zero Degree Boom Angle
Boom Main Boom Length in Meters
Angle 10.9 12.2 15.2
5,415 4,005 1,775
0°
(9.2) (10.4) (13.5)
NOTE: ( ) Reference radii in meters. 80039617
** Boom length is with inner-mid fully extended and outer-mid & fly fully retracted.
RT765E-2 - S/N 232673 17
 ON RUBBER CAPACITIES

STATIONARY CAPACITIES - 360° NOTES TO ALL RUBBER CAPACITY CHARTS:

1. Capacities are in kilograms and do not ex-
Radius #9005
ceed 85% of tipping loads as determined by
in Main Boom Length in Meters test in accordance with SAE J765.
Meters
10.9 12.2 15.2 **18.4 21.3 2. Capacities are applicable to machines
20,525 18,000 equipped with 29.5x25 (28 or 34 ply) Gen-
3 eral/Titan, Denman Rock Plus, Denman
(70) (72)
Broadway and Advance bias ply tires at 4.5
19,250 18,000 13,425
3.5 bar cold inflation pressure.
(67) (69.5) (74)
17,875 17,275 12,875 3. Capacities appearing above the bold line
4 are based on structural strength and tipping
(64) (67) (72)
should not be relied upon as a capacity
16,500 16,250 12,100 9,480 limitation.
4.5
(60.5) (64) (69.5) (73.5)
4. Capacities are applicable only with machine
14,175 13,900 11,575 9,480
5 on firm level surface.
(57.5) (61.5) (67.5) (72)
10,150 10,000 9,930 9,480 7,845 5. On rubber lifting with boom extensions not
6 permitted.
(50.5) (55.5) (63.5) (68.5) (71.5)
7,630 7,500 7,460 7,350 7,595 6. For pick and carry operation, boom must be
7 centered over front of machine, mechanical
(42.5) (49) (59) (65) (69)
swing lock engaged and load restrained
5,885 5,785 5,695 5,630 5,870
8 from swinging. When handling loads in the
(32.5) (42) (54) (61.5) (66)
structural range with capacities close to
4,510 4,405 4,375 4,350 4,625 maximum ratings, travel should be reduced
9
(16.5) (33) (49) (57.5) (62.5) to creep speeds.
3,305 3,280 3,345 3,525 7. Axle lockouts must be functioning when
10
(20.5) (43.5) (53.5) (59.5) lifting on rubber.
1,810 1,680 2,085
12 8. All lifting depends on proper tire inflation,
(29.5) (45) (53)
capacity and condition. Capacities must be
1,155 reduced for lower tire inflation pressures.
14
(45.5) See lifting capacity chart for tire used. Dam-
Min. boom angle (°) for indicated length aged tires are hazardous to safe operation
(no load)
35 39 of crane.
Max. boom length (m) at 0° boom angle
15.2 9. Creep - not over 61 m of movement in any 30
(no load)
minute period and not exceeding 1.6 km/h.
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
Lifting Capacities at Zero Degree Boom Angle
Boom Main Boom Length in Meters
Angle 10.9 12.2 15.2
4,160 2,925 1,030
0°
(9.2) (10.4) (13.5)
80039623
NOTE: ( ) Reference radii in meters.
** Boom length is with inner-mid fully extended and outer-mid & fly
fully retracted.
RT765E-2 - S/N 232673 18
 ON RUBBER CAPACITIES (cont'd.)
PICK & CARRY CAPACITIES (UP TO 4.0 km/h) -
BOOM CENTERED OVER FRONT (See note 6)

Radius #9006
in Main Boom Length in Meters
Meters
10.9 12.2 15.2 **18.4 21.3
21,400 19,950 15,400
3
(70) (72) (76)
21,400 19,950 15,400
3.5
(67) (69.5) (74)
20,725 19,700 15,400 12,925
4
(64) (67) (72) (75)
19,750 19,325 15,400 12,925 9,685
4.5
(60.5) (64) (69.5) (73.5) (76)
18,225 18,025 15,200 12,925 9,685
5
(57.5) (61.5) (67.5) (72) (74.5)
15,200 15,025 14,675 12,925 9,685
6
(50.5) (55.5) (63.5) (68.5) (71.5)
13,025 12,875 12,750 12,125 9,685
7
(42.5) (49) (59) (65) (69)
11,100 11,025 11,025 11,025 9,685
8
(32.5) (42) (54) (61.5) (66)
9,495 9,170 9,460 9,550 9,685
9
(16.5) (33) (49) (57.5) (62.5)
6,425 6,500 7,830 8,300
10
(20.5) (43.5) (53.5) (59.5)
4,795 4,780 5,215
12
(29.5) (45) (53)
3,490 3,940
14
(34.5) (45.5)
2,440 2,950
16
(18.5) (36.5)
2,045
18
(25)
Min. boom angle (°) for indicated length (no load) 0
Max. boom length (m) at 0° boom angle (no load) 21.3
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for operating
instructions.
Lifting Capacities at Zero Degree Boom Angle
Boom Main Boom Length in Meters
Angle 10.9 12.2 15.2 **18.4 21.3
9,140 5,995 3,800 2,125 1,480
0°
(9.2) (10.4) (13.5) (16.6) (19.6)
80040888
NOTE: ( ) Reference radii in meters.
** Boom length is with inner-mid fully extended and outer-mid & fly
fully retracted.
RT765E-2 - S/N 232673 19
 TIRE INFLATION - PSI (BAR)

SIZE LIFTING SERVICE , GENERAL

(FRONT TRA TRAVEL AND EXTENDED TRAVEL
& CODE
REAR) STATIC, CREEP &
2.5 MPH (4.0 km/h)

29.5x25 (28 or 34) E-3 65 (4.5)

General/Titan, (See operator's manual for
Denman Broadway extended roading.)
/ Rock Plus

RT765E-2 - S/N 232673 20