Division 3

Concrete
Estimating Tips 032 Concrete Reinforcement
Ascertain that the reinforcing steel take-off
General has included all accessories, cutting, bending
Always obtain concrete prices from suppliers near the and an allowance for lapping, splicing and
job site. Remember to add for waste, waste.
particularly for slabs and footings on grade.
Estimator shall pay attention to steel bars
031 Concrete Formwork supports with respect to rust prevention
A primary cost for concrete construction is forming. classification as being maximum, moderate
Most jobs today are constructed with prefabricated or with no protection.
forms. The selection of the forms best suited for the
job and the total square meter of forms required for Estimator shall be aware that placing
efficient concrete forming and placing are key reinforcing steel in architectural concrete
elements in estimating concrete construction. Enough walls, having smaller sizes, horizontal, vertical short
forms must be available for erection to make efficient runs, and wired together in a costly operation.
use of the concrete placing equipment and crew.
033 Cast-in-Place Concrete
Concrete accessories for forming and placing depend When estimating structural concrete, pay
upon the systems used. The productivity rate as particular attention to requirements for
shown in this book includes the form preparation, concrete additives, curing methods and
erecting, forms removal and cleaning. Concrete forms surface treatments. Special consideration for
are usually estimated by computing the surface area climate, hot or cold, must be included in your
of the form in contact with concrete. estimate. Be sure to include requirements for
concrete placing equipment and concrete
Estimators shall focus on any special formwork finishing.
requirements such as:
l Risers for stepped wall footings. 034 Precast Concrete
l Keyways, as grooves are usually formed in the The cost of hauling precast structural
top of footings. members is often an important factor. For
l Design proper wall forms to withstand the horizontal this reason, it is important to get a quote from
pressure exerted by the flow of concrete. the nearest supplier.
l Curved walls require more studs and bracing.
l Bulkheads shall be considered for all opening in Estimator shall consider additional forms for column
formwork, estimator shall allow an average of depression at all column heads on the flat slabs.
0.06 M3 form per square meter opening. Estimator shall be aware that form work for stairs
l Check for any setbacks for all wall foundations running with two (2) flights between floors and with an
that extend above grade. intermediate landing costs about 30% more than a
l Check for any continuous hunch in concrete wall straight flight run.
forms. Architectural concrete forms shall be priced based
l Using high early strength cement instead of on the contractor know-how to detail them, including
ordinary portland cement will reduce the cost of every piece of plywood, stud, wale, bolt, window
forms in large jobs. boxes and lumbar for reveals.
l Productivity rate for slab forms considers the use of
adjustable sectional steel scaffolding units for
shoring.

57
DIVISION 03 : CONCRETE
CSI ITEM DESCRIPTION UNIT
CODE

FORMS IN PLACE, EQUIPMENT FOUNDATIONS:

SQM
Forms in place, equipment foundations 1 use CON-
TACT
AREA

Forms in place, equipment foundations 5 use "

FORMS IN PLACE, FOOTINGS:

031 154 FORMS IN PLACE, EQUIPMENT FOUNDATIONS:

SQM
CON-
031 154-0010 Forms in place, equipment foundations 1 use
TACT
AREA

031 154-0150 Forms in place, equipment foundations 5 use "

031 158 FORMS IN PLACE, FOOTINGS:

SQM
CON-
031 158-0010 Forms in place, Footings Continuous wall, 1 use
TACT
AREA

031 158-0150 Forms in place, Footings Continuous wall, 5 use "

031 158-1000 Integral starter wall, to 100 mm high, 1 use LM
031 158-1550 Keyway, 5 use, tapered wood, 50 mm x 150 mm
031 158-2050 Keyway, 5 use, tapered plastic, 50 mm x 100 mm

031 158-3000 Forms in place,pile cap, square or rectangular, 1 use

031 158-3150 Forms in place,pile cap,square or rectangular, 5 use

031 158-4000 Forms in place,pile cap,Triangular or hexagonal, 1 use
031 158-5000 Forms in place,spread footings, 1 use
031 158-5150 Forms in place,spread footings, 5 use
031 158-6000 Supports for dowels,plinths or templates, 600 mm x 600 mm footing EA
031 158-6150 Supports for dowels,plinths or templates, 3650 mm x 3650 mm footing ,,
 CREW
CREW CREW DAILY MAN EQUIP.
STRUCTURE HOURE
EQUIP. OUTPUT HOURS HOURS
S

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
0.125 Equip. Operator 50.00 9.00 11.880 4.209 0.758
1.000 Power Tools
0.125 Truck Crane 35 Ton

" 50.00 9.00 13.800 3.623 0.652

50.00 9.00

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
0.125 Equip. Operator 50.00 9.00 11.880 4.209 0.758
1.000 Power Tools
0.125 Truck Crane 35 Ton

" 50.00 9.00 13.800 3.623 0.652

50.00 9.00

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
0.125 Equip. Operator 50.00 9.00 34.150 1.464 0.264
1.000 Power Tools
0.125 Truck Crane 35 Ton

50.00 9.00 40.420 1.237 0.223

50.00 9.00 155.000 0.323 0.058
1 Carpenter 8.00 0.00 115.000 0.070 0.000
" 8.00 0.00 115.000 0.070 0.000

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
0.125 Equip. Operator 50.00 9.00 28.200 1.773 0.319
1.000 Power Tools
0.125 Truck Crane 35 Ton

50.00 9.00 33.600 1.488 0.268

50.00 9.00 27.800 1.799 0.324
50.00 9.00 30.330 1.649 0.297
50.00 9.00 36.160 1.383 0.249
50.00 9.00 27.000 1.852 0.333
50.00 9.00 18.000 2.778 0.500
b item Qty unit unit rate Amount
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

031 CONCRETE FORMWORK

030 100 STRUCT C.I.P. FORMWORK
031 110 ACCESSORIES,ANCHOR BOLTS Incl. nut and washer
031 110-0200 Anchor bolt,including nut & washer,16 mm Diameter, 305 mm Long (5/8",12") EA 1 Carpenter 8.00 0.00 60.000 0.133 0.000

031 110-0300 Anchor bolt,including nut & washer,16 mm Diameter, 610 mm Long 8.00 0.00 45.000 0.178 0.000

031 110-0500 Anchor bolt,including nut & washer, 20 mm Diameter, 610 mm Long 8.00 0.00 40.000 0.200 0.000

031 110-0700 Anchor bolt,including nut & washer, 22 mm Diameter, 610 mm Long 8.00 0.00 30.000 0.267 0.000

031 110-0800 Anchor bolt,including nut & washer, 24 mm Diameter, 305 mm Long (1",12") 8.00 0.00 42.000 0.190 0.000

031 110-0950 Anchor bolt,including nut & washer, 24 mm Diameter, 914 mm Long 8.00 0.00 18.000 0.444 0.000

031 111 ANCHOR BOLTS with hex nuts and washers,zinc plated
031 111-0800 Anchor bolt with hex nut & washer,zinc plated,M8, 8 mm Diameter x 100 mm Long to 200 mm Long EA 1 Carpenter 8.00 0.00 80.000 0.100 0.000
031 111-1270 Anchor bolt with hex nut & washer,zinc plated,M12, 12 mm Diameter x 320 mm Long 8.00 0.00 68.000 0.118 0.000
031 111-1670 Anchor bolt with hex nut & washer,zinc plated,M16, 16 mm Diameter x 320 mm Long 8.00 0.00 62.000 0.129 0.000
031 111-2070 Anchor bolt with hex nut & washer,zinc plated,M20, 20 mm Diameter x 400 mm Long 8.00 0.00 50.000 0.160 0.000
031 111-2450 Anchor bolt with hex nut & washer,zinc plated,M24, 24 mm Diameter x 320 mm Long 8.00 0.00 58.000 0.138 0.000
031 112 ACCESSORIES,CHAMFER STRIPS:
031 112-2000 Chamfer strip,Polyvinyl chloride,15 mm wide with leg LM 1 Carpenter 8.00 0.00 125.000 0.064 0.000

031 112-2200 Chamfer strip,Polyvinyl chloride, 20 mm chamfer with leg 8.00 0.00 120.000 0.067 0.000

031 112-2400 Chamfer strip,Polyvinyl chloride, 25 mm radius with leg 8.00 0.00 115.000 0.070 0.000

031 112-2800 Chamfer strip,Polyvinyl chloride, 30 mm radius 8.00 0.00 110.000 0.073 0.000

031 112-5200 Chamfer strip,steel 20 mm wide 8.00 0.00 100.000 0.080 0.000

031 112-5400 Chamfer strip,steel 25 mm wide 8.00 0.00 96.000 0.083 0.000

031 114 ACCESSORIES COLUMN FORM:

031 114-1300 Column clamps adjustable 760 mm x 760 mm SET 1 Carpenter 8.00 0.00 15.000 0.533 0.000

031 114-3300 Column clamps adjustable 1.5 m x 1.5 m ,, ,, 8.00 0.00 5.000 1.600 0.000

031 116 ACCESSORIES,DOVETAIL ANCHOR SYSTEM:

031 116-0500 Dovetail,Anchor slot,filled, 24 ga. LM 1 Carpenter 8.00 0.00 92.000 0.087 0.000

031 116-0600 Dovetail,Anchor slot,Galvanized, 20 ga. 8.00 0.00 85.000 0.094 0.000

031 116-0800 Dovetail,Anchor slot, 454 gram copper, foam filled 8.00 0.00 80.000 0.100 0.000

031 116-0900 Dovetail,Anchor slot, 26 ga. stainless steel, foam filled 8.00 0.00 80.000 0.100 0.000

031 116-1200 Dovetail,Brick anchor,galv., 89 mm Long, 16 ga. 100 PCS 1 Bricklayer 8.00 0.00 7.000 1.143 0.000

031 116-2100 Dovetail,Anchor Cavity wall,galv., 127 mm Long, 12 ga. 8.00 0.00 7.000 1.143 0.000

031 116-3100 Dovetail,Furring anchors,corr.,galv., 38 mm Long, 12 ga. 8.00 0.00 7.000 1.143 0.000

031 116-6100 Dovetail,Stone anchors, 89 mm Long, galv., 6 mm x 25 mm wide 8.00 0.00 6.000 1.333 0.000

031 122 ACCESSORIES,INSERTS:

031 122-2300 Inserts,Continuous slotted, 914 mm Long 8 ga. EA 1 Carpenter 8.00 0.00 50.000 0.160 0.000

031 122-2350 Inserts,Continuous slotted, 1.5 m Long 8 ga. ,, " 8.00 0.00 45.000 0.178 0.000

031 126 ACCESSORIES,SLEEVES AND CHASES:

031 126-0150 Sleeves & Chases,Plastic type,1 use, 229 mm Long, 100 mm dia.(4") EA 1 Carpenter 8.00 0.00 75.000 0.107 0.000

031 126-0250 Sleeves & Chases,Plastic type,1 use, 229 mm Long, 300 mm dia.(12") ,, " 8.00 0.00 50.000 0.160 0.000

031 132 EXPANSION JOINT

031 132-0010 Expansion Joint,Keyed cold joint, 24 ga.,incl.stakes, 90 mm high LM 1 Carpenter 8.00 0.00 50.000 0.160 0.000

031 132-0150 Expansion Joint,Keyed cold joint, 24 ga.,incl.stakes, 190 mm high 1 Carpenter 8.00 0.00 45.000 0.178 0.000

031 132-0350 Expansion Joint,Poured asphalt, plain, 25 mm x 50 mm 1 Common Labor 8.00 0.00 110.000 0.073 0.000

031 132-0550 Expansion Joint,Neoprene,liquid,cold applied, 25 mm x 50 mm 1 Common Labor 8.00 0.00 110.000 0.073 0.000

031 132-0750 Expansion Joint,Polyurethane, 1 part, 13 mm x 25 mm 2 Common Labor 8.00 0.00 110.000 0.073 0.000

031 132-1150 Expansion Joint,Rubberized hot applied,fuel resistant, 25 mm x 50 mm " 8.00 0.00 110.000 0.073 0.000

031 132-2000 Expansion Joint,Premolded,bituminous fiber,13 mm x 150 mm 1 Carpenter 8.00 0.00 120.000 0.067 0.000

031 132-2250 Expansion Joint,Cork with resin binder, 13 mm x 150 mm 8.00 0.00 96.000 0.083 0.000

031 132-2550 Expansion Joint,Neoprene sponge,closed cell, 25 mm x 300 mm 8.00 0.00 96.000 0.083 0.000

031 132-2750 Expansion Joint,Polyethylene foam,13 mm x 150 mm 8.00 0.00 96.000 0.083 0.000

031 132-3000 Expansion Joint,Polyethylene backer rod, 10 mm to 25 mm diameter 8.00 0.00 120.000 0.067 0.000

031 132-3100 Expansion Joint,Polyethylene backer rod, 25 mm dia. (1") 8.00 0.00 120.000 0.067 0.000

031 132-3800 Expansion Joint,Polyurethane foam,regular,closed cell, 25 mm x 300 mm LM 1 Carpenter 8.00 0.00 75.000 0.107 0.000

031 132-4300 Expansion Joint,Rubber,gray sponge,13 mm x 150 mm LM 1 Carpenter 8.00 0.00 110.000 0.073 0.000

031 138 FORMS IN PLACE, BEAMS AND GIRDERS:

0.125 Carpenter Foreman
SQM 4.000 Carpenters
CON- 2.000 Laborers
031 138-0650 Forms in place,Beam and Girder,exterior spandrel, 305 mm wide,4 use TACT 0.250 Equip. Operator
51.00 18.00 19.460 2.621 0.925
AREA 2.000 Power Tools
0.250 Truck Crane 35 Ton

031 138-1500 Forms in place,Exterior spandrel, 610 mm wide, 1 use 51.00 18.00 18.290 2.788 0.984

031 138-2150 Forms in place,Interior beams, 305 mm wide, 5 use 51.00 18.00 22.990 2.218 0.783

031 138-2500 Forms in place,Interior beams, 610mm wide, 1 use 51.00 18.00 20.900 2.440 0.861

031 138-3150 Forms in place,Beam and Girder,encasing steel frame,hung, 5 use 51.00 18.00 30.080 1.695 0.598

031 138-3650 Forms in place,Beam bottoms only, 610 mm wide, 5 use 51.00 18.00 27.740 1.839 0.649

031 138-4000 Forms in place,Beam sides only,vertical, 914 mm high, 1 use 51.00 18.00 29.570 1.725 0.609

031 138-4500 Forms in place,Sloped sides, 914 mm high, 1 use 51.00 18.00 22.670 2.250 0.794

031 138-5000 Forms in place,Upstanding beams, 914 mm high, 1 use 51.00 18.00 16.620 3.069 1.083

031 142 FORMS IN PLACE, COLUMNS:

0.125 Carpenter Foreman
4.000 Carpenters
2.000 Laborers
031 142-0500 Column form,Round fiberglass, 5 use/mo., 300 mm dia. 4.2 m high. LM
0.250 Equip. Operator
51.00 18.00 73.000 0.699 0.247
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 142-0650 Column form,Round fiberglass, 5 use/mo.,rent, 610 mm dia. 4.2 m high. 51.00 18.00 64.000 0.797 0.281

031 142-0800 Column form,Round fiberglass, 5 use/mo., 760 mm dia. 4.2 m high. 51.00 18.00 58.000 0.879 0.310

031 142-0850 Column form,Round fiberglass, 5 use/mo., 914 mm dia. 4.2 m high 51.00 18.00 54.700 0.932 0.329

031 142-1700 Column form,Round fiber tube,1 use, 400 mm dia. 4.2 m high. 51.00 18.00 59.700 0.854 0.302

031 142-1800 Column form,Round fiber tube,1 use, 610 mm dia. 4.2 m high 51.00 18.00 55.000 0.927 0.327

031 142-1900 Column form,Round fiber tube,1 use, 914 mm dia. 4.2 m high. 51.00 18.00 50.000 1.020 0.360

031 142-2000 Column form,Round fiber tube,1 use,1220 mm dia. 4.2 m high. 51.00 18.00 29.300 1.741 0.614

031 142-3050 Column form,Round,steel, 5 use/mo.,regular duty, 400 mm dia., 6 m high 51.00 18.00 43.500 1.172 0.414

031 142-3150 Column form,Round Steel, 5 use/mo.,Heavy duty, 610 mm dia. 6 m high 51.00 18.00 30.300 1.683 0.594

031 142-3200 Column form,Round Steel, 5 use/mo., Heavy duty, 762 mm dia. 6 m high 51.00 18.00 25.800 1.977 0.698

031 142-3250 Column form,Round Steel, 5 use/mo.,Heavy duty, 914 mm dia. 7.6 m high. 51.00 18.00 22.600 2.257 0.796

031 142-3300 Column form,Round Steel, 5 use/mo.,Heavy duty,1220 mm dia. 7.6 m high 51.00 18.00 18.200 2.802 0.989

1.00 Carpenter Foreman

4.00 Carpenters
2.00 Laborers
031 142-3350 Column form,Round Steel, 4 use/mo.,Heavy duty,1525 mm dia. 8 m high. 0.50 Equip. Operator
60.00 12.00 15.500 3.871 0.774
1.00 Power Tools
0.50 Truck Crane 35 Ton

031 142-4000 Column form,Round Steel,Column capitals, 5 use/mo., 600 mm col, 1200 mm cap dia. EA 60.00 12.00 14.000 4.286 0.857
031 142-4100 Column form,Round Steel,Column capitals, 5 use/mo., 600 mm col, 1800 mm cap dia. ,, 60.00 12.00 12.250 4.898 0.980
0.125 Carpenter Foreman
SQM 4.000 Carpenters
CON- 2.000 Laborers
031 142-5500 Column form,Plywood, 300 mm x 300 mm columns, 1 use TACT 0.250 Equip. Operator
51.00 18.00 20.360 2.505 0.884
AREA 2.000 Power Tools
0.250 Truck Crane 35 Ton

031 142-5650 Column form,Plywood, 300 mm x 300 mm columns, 5 use 51.00 18.00 24.980 2.042 0.721

031 142-6000 Column form,Plywood, 400 mm x 400 mm columns, 1 use 51.00 18.00 20.870 2.444 0.862

031 142-6650 Column form,Plywood, 600 mm x 600 mm columns, 5 use 51.00 18.00 27.850 1.831 0.646

031 142-7000 Column form,Plywood, 900 mm x 900 mm columns, 1 use 51.00 18.00 23.040 2.214 0.781

031 142-7100 Column form,Plywood, 900 mm x 900 mm columns, 5 use 51.00 18.00 29.150 1.750 0.617

031 142-7600 Column form,Steel framed plywood, 5 use/month, 300 mm x 300 mm 51.00 18.00 33.510 1.522 0.537

031 142-7650 Column form,Steel framed plywood, 5 use/month, 400 mm x 400 mm 51.00 18.00 35.190 1.449 0.512

031 142-7700 Column form,Steel framed plywood, 5 use/month, 500 mm x 500 mm 51.00 18.00 36.070 1.414 0.499

031 142-7750 Column form,Steel framed plywood, 5 use/month, 600 mm x 600 mm 51.00 18.00 36.970 1.379 0.487

031 146 FORMS IN PLACE, CULVERT:

Page 63
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

0.125 Carpenter Foreman

SQM 4.000 Carpenters
CON- 2.000 Laborers
031 146-0010 Form Culvert,1524 mm to 2438 mm rectangular, 1 use TACT 0.250 Equip. Operator
51.00 18.00 17.000 3.000 1.059
AREA 2.000 Power Tools
0.250 Truck Crane 35 Ton

FORMS IN PLACE, ELEVATED SLABS:

031 150
STEEL JACK SUPPORTS
0.125 Carpenter Foreman
4.000 Carpenters
2.000 Laborers
031 150-1000 Forms in place,Flat plate to 4.6 m high, 1 use SQM
0.250 Equip. Operator
51.00 18.00 65.850 0.774 0.273
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 150-1150 Forms in place,Flat plate to 4.6 m high, 5 use 51.00 18.00 72.000 0.708 0.250

031 150-1600 Forms in place,Flat plate 6.2 m to 11 m high ceiling, 5 use 51.00 18.00 62.000 0.823 0.290

031 150-2150 Forms in place,Flat slab with drop panels, to 4.6 m high, 5 use 51.00 18.00 68.000 0.750 0.265

031 150-3500 Forms in place,Floor slab, with 508 mm metal pans, 1 use 51.00 18.00 52.330 0.975 0.344

031 150-3650 Forms in place,Floor slab, with 508 mm metal pans, 5 use/month 51.00 18.00 59.000 0.864 0.305

031 150-3760 Forms in place,Floor slab, with 762 mm metal pans, 5 use/month. 51.00 18.00 65.320 0.781 0.276

031 150-4000 Forms in place,Floor slab, with 483 mm metal domes, 1 use 51.00 18.00 51.200 0.996 0.352

031 150-4150 Forms in place,Floor slab, with 483 mm metal domes, 2 use/month. 51.00 18.00 59.260 0.861 0.304

031 150-4500 Forms in place,Floor slab,with 762 mm fiberglass domes, 1 use 51.00 18.00 51.200 0.996 0.352

031 150-4550 Forms in place,Floor slab,with 762 mm fiberglass domes, 5 use 51.00 18.00 64.270 0.794 0.280

031 150-5000 Forms in place,Floor slab, with hordi blocks 5 uses forms 51.00 18.00 63.140 0.808 0.285

0.125 Carpenter Foreman

SQM 4.000 Carpenters
CON- 2.000 Laborers
031 150-6500 Forms in place,Curb forms,wood,150 mm to 300 mm H, on elevated slabs,1 use TACT 0.125 Equip. Operator
50.00 9.00 23.400 2.137 0.385
AREA 1.000 Power Tools
0.125 Truck Crane 35 Ton

031 150-8050 Forms in place,Perimeter deck and rail for elevated slabs, Curved ,, 50.00 9.00 21.080 2.372 0.427

031 150-8750 Forms in place,Void forms,round fiber, 300 mm diameter,void (12") LM 50.00 9.00 100.000 0.500 0.090

031 154 FORMS IN PLACE, EQUIPMENT FOUNDATIONS:

0.125 Carpenter Foreman
SQM 4.000 Carpenters
CON- 2.000 Laborers
031 154-0010 Forms in place, equipment foundations 1 use TACT 0.125 Equip. Operator
50.00 9.00 11.880 4.209 0.758
AREA 1.000 Power Tools
0.125 Truck Crane 35 Ton

031 154-0150 Forms in place, equipment foundations 5 use " " 50.00 9.00 13.800 3.623 0.652

031 158 FORMS IN PLACE, FOOTINGS: 50.00 9.00

0.125 Carpenter Foreman

SQM 4.000 Carpenters
CON- 2.000 Laborers
031 158-0010 Forms in place, Footings Continuous wall, 1 use TACT 0.125 Equip. Operator
50.00 9.00 34.150 1.464 0.264
AREA 1.000 Power Tools
0.125 Truck Crane 35 Ton

031 158-0150 Forms in place, Footings Continuous wall, 5 use " 50.00 9.00 40.420 1.237 0.223

031 158-1000 Integral starter wall, to 100 mm high, 1 use LM 50.00 9.00 155.000 0.323 0.058

031 158-1550 Keyway, 5 use, tapered wood, 50 mm x 150 mm 1 Carpenter 8.00 0.00 115.000 0.070 0.000

031 158-2050 Keyway, 5 use, tapered plastic, 50 mm x 100 mm " 8.00 0.00 115.000 0.070 0.000

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
031 158-3000 Forms in place,pile cap, square or rectangular, 1 use 0.125 Equip. Operator
50.00 9.00 28.200 1.773 0.319
1.000 Power Tools
0.125 Truck Crane 35 Ton

031 158-3150 Forms in place,pile cap,square or rectangular, 5 use 50.00 9.00 33.600 1.488 0.268

031 158-4000 Forms in place,pile cap,Triangular or hexagonal, 1 use 50.00 9.00 27.800 1.799 0.324

031 158-5000 Forms in place,spread footings, 1 use 50.00 9.00 30.330 1.649 0.297

031 158-5150 Forms in place,spread footings, 5 use 50.00 9.00 36.160 1.383 0.249

031 158-6000 Supports for dowels,plinths or templates, 600 mm x 600 mm footing EA 50.00 9.00 27.000 1.852 0.333

031 158-6150 Supports for dowels,plinths or templates, 3650 mm x 3650 mm footing ,, 50.00 9.00 18.000 2.778 0.500

031 162 FORMS IN PLACE, GRADE BEAM:

0.125 Carpenter Foreman
SQM 4.000 Carpenters
CON- 2.000 Laborers
031 162-0010 Forms,Grade Beam 1 use TACT 0.125 Equip. Operator
50.00 9.00 43.000 1.163 0.209
AREA 1.000 Power Tools
0.125 Truck Crane 35 Ton

031 162-0150 Forms,Grade Beam 5 use " " 50.00 9.00 50.000 1.000 0.180

031 166 FORMS IN PLACE, MAT FOUNDATION:

0.125 Carpenter Foreman
SQM 4.000 Carpenters
CON- 2.000 Laborers
031 166-0010 Forms in place,mat foundation 1 use TACT 0.125 Equip. Operator
50.00 9.00 23.600 2.119 0.381
AREA 1.000 Power Tools
0.125 Truck Crane 35 Ton

031 166-0120 Forms in place,mat foundation 5 use " " 50.00 9.00 28.300 1.767 0.318

031 170 FORMS IN PLACE, SLAB ON GRADE:

0.125 Carpenter Foreman
4.000 Carpenters
2.000 Laborers
031 170-1000 Bulkhead forms with keyway, 1 use , 2 piece LM
0.125 Equip. Operator
50.00 9.00 155.000 0.323 0.058
1.000 Power Tools
0.125 Truck Crane 35 Ton

031 170-1400 Bulkhead forms w/keyway, 1 piece expanded metal, left in place ,, 50.00 9.00 475.000 0.105 0.019
SQM
CON-
031 170-2000 Curb forms, wood,150 mm to 450 mm high,on grade, 1 use TACT
50.00 9.00 22.700 2.203 0.396
AREA

031 170-2150 Curb forms, wood,150 mm to 450 mm high,on grade, 5 use ,, 50.00 9.00 26.300 1.901 0.342

031 170-4050 Edge forms for slab blockouts, 1 use to 600 mm high LM 50.00 9.00 62.000 0.806 0.145
SQM
CON-
031 170-6000 Trench forms in floor, 1 use TACT
50.00 9.00 17.500 2.857 0.514
AREA

031 170-6150 Trench forms in floor, 5 use ,, 50.00 9.00 19.200 2.604 0.469

031 174 FORMS IN PLACE, STAIRS:

0.125 Carpenter Foreman
4.000 Carpenters
2.000 Laborers
031 174-0010 Forms in place,Stairs (Slant length x width), 1 use SQM
0.250 Equip. Operator
51.00 18.00 6.700 7.612 2.687
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 174-0150 Forms in place,Stairs (Slant length x width), 5 use " " 51.00 18.00 9.000 5.667 2.000

031 182 FORMS IN PLACE, WALLS:

0.125 Carpenter Foreman
4.000 Carpenters
2.000 Laborers
031 182-0100 Box out for openings up to 1 square meter in 400 mm wall thick EA
0.250 Equip. Operator
51.00 18.00 12.000 4.250 1.500
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 182-0600 Bulkhead forms w/keyway, 1 piece expanded metal, left in place LM 1 Carpenter 8.00 0.00 100.000 0.080 0.000

0.125 Carpenter Foreman

SQM 4.000 Carpenters
CON- 2.000 Laborers
031 182-2000 Job built plyform wall forms,to 2400 mm high, 1 use TACT 0.250 Equip. Operator
51.00 18.00 30.450 1.675 0.591
AREA 2.000 Power Tools
0.250 Truck Crane 35 Ton

031 182-2150 Job built plyform wall forms,to 2400 mm high, 5 use 51.00 18.00 38.200 1.335 0.471

031 182-2550 Job built plyform wall forms over 2400 mm to 4800 mm high, 5 use 51.00 18.00 31.100 1.640 0.579

031 182-2850 Job built plyform wall forms over 4800 mm high, 5 use 51.00 18.00 25.900 1.969 0.695

031 182-4000 Radial wall forms,smooth curved, 1 use 51.00 18.00 22.390 2.278 0.804

031 182-4150 Radial wall forms,smooth curved, 5 use 51.00 18.00 27.950 1.825 0.644

031 182-4450 Radial wall forms, curved, with 600 mm chords, 5 use 51.00 18.00 33.540 1.521 0.537

031 182-4600 Retaining wall forms, battered, to 2400 mm high, 1 use 51.00 18.00 24.650 2.069 0.730

031 182-4750 Retaining wall forms, battered, to 2400 mm high, 5 use 51.00 18.00 31.000 1.645 0.581

031 182-5050 Retaining wall forms, battered, over 2400 mm to 4800 mm high, 5 use 51.00 18.00 22.800 2.237 0.789

031 182-6200 Liners for forms Ribbed look, 13 mm & 19 mm deep, 5 use 1 Carpenter 8.00 0.00 68.900 0.116 0.000

031 182-6400 Liners for forms Rustic brick pattern, 5 use. 8.00 0.00 66.800 0.120 0.000

031 182-6600 Liners for forms striated,random,10 mm x 10 mm deep, 5 use 8.00 0.00 68.900 0.116 0.000

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
031 182-7800 Wall form,Modular prefabricated plywood, to 2400 mm high, 1 use/month 0.250 Equip. Operator
51.00 18.00 62.300 0.819 0.289
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 182-7860 Wall form,Modular prefabricated plywood, to 2400 mm high, 5 use/month 51.00 18.00 66.700 0.765 0.270

Page 64
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
031 182-8060 Wall form,Modular prefabricated plywood, to 4800 mm high, 5 use/month 0.250 Equip. Operator
51.00 18.00 46.700 1.092 0.385
2.000 Power Tools
0.250 Truck Crane 35 Ton

031 182-8660 Form,Pilasters, 5 use 51.00 18.00 30.350 1.680 0.593

031 182-9060 Wall form,Steel framed plywood, to 2400 mm high, 5 use/month 51.00 18.00 51.000 1.000 0.353

031 182-9260 Wall form,Steel framed plywood,over 2400 mm to 4800 mm high, 5 use/month 51.00 18.00 50.800 1.004 0.354

031 182-9460 Wall form,Steel framed plywood,over 4800 mm to 6100 mm high, 5 use/month 51.00 18.00 45.700 1.116 0.394

031 186 GAS STATION FORMS:

031 186-0010 Forms,Curb fascia, with template 12 ga.steel,left in place, 230 mm high LM 1 Carpenter 8.00 0.00 12.000 0.667 0.000

0.125 Carpenter Foreman

4.000 Carpenters
2.000 Laborers
031 186-2550 Island forms, 6100mm long, 230 mm high, 1500 mm wide EA
0.125 Equip. Operator
50.00 9.00 6.000 8.333 1.500
1.000 Power Tools
0.125 Truck Crane 35 Ton

031 190 SCAFFOLDING See division 015-254

031 196 SLIPFORMS:
1.00 Skilled Foreman
SQM 4.00 Skilled workers
CON- 2.00 Laborers
031 192-1000 Slipforms Buildings, Average TACT 0.25 Equip. Operator
58.00 6.00 78.000 0.744 0.077
AREA 0.25 Truck Crane - Hauling
0.50 Hyd. Jack with Rods

031 198 WATERSTOP:

031 198-0010 Waterstop,Polyvinyl chloride, ribbed 5 mm thk. 100 mm wide LM 1 Carpenter 8.00 0.00 38.000 0.211 0.000

031 198-0500 Waterstop,Ribbed, PVC, with center bulb, 5 mm thick, 230 mm wide 8.00 0.00 32.000 0.250 0.000

031 198-0850 Waterstop,Dumbbell type, PVC, 150 mm wide, 10 mm thick 8.00 0.00 33.000 0.242 0.000

031 198-1250 Waterstop,Split PVC, 10mm thick, 150 mm wide 8.00 0.00 33.000 0.242 0.000

031 198-2050 Waterstop,Rubber,flat dumbbell, 10 mm thick, 230 mm wide 8.00 0.00 32.000 0.250 0.000
Waterstop fittings,Rubber,flat,dumbbell or center bulb, 10 mm thk.
031 198-5500 8.00 0.00 25.000 0.320 0.000
flat cross or tee,150 - 230 mm wide
Waterstop fittings,Rubber,flat,dumbbell or center bulb, 10 mm thk.
031 198-6500 8.00 0.00 30.000 0.267 0.000
flat EII 150 - 230 mm wide
Waterstop fittings, Rubber,flat,dumbbell or center bulb,10 mm thk.
031 198-7000 8.00 0.00 18.000 0.444 0.000
Vertical Tee,150 - 230 mm wide
Waterstop fittings, Rubber,flat,dumbbell or center bulb, 10 mm thk.
031 198-7500 8.00 0.00 27.000 0.296 0.000
Vertical EII 150 - 230 mm wide
032 CONCRETE REINFORCEMENT
032 100 REINFORCING STEEL:
032 107 REINFORCING IN PLACE A615, GRADE 60:
0.25 Labor Foreman
4.00 Steel Fixtures
2.00 Common Laborers
MET.
032 107-0100 Grade 60,Reinforcement,Beams & Girders,10 mm to 25 mm TON
0.25 Equip. Operator 52.00 10.00 1.100 47.273 9.091
1.00 Power Tool
0.125 Crane
0.125 Bed Truck

032 107-0150 Grade 60,Reinforcement,Beams & Girders, 25 mm to 40 mm 40.00 12.00 1.400 37.143 8.571

032 107-0200 Grade 60,Reinforcement,Columns, 10 mm to 25 mm 40.00 12.00 1.000 52.000 12.000

032 107-0250 Grade 60,Reinforcement,Columns, 25 mm to 40 mm 40.00 12.00 1.200 43.333 10.000

032 107-0300 Grade 60,Reinforcement,Spirals, 10 mm diam, hot rolled, to 350 mm dia. ) 40.00 12.00 1.200 43.333 10.000

032 107-0400 Grade 60,Reinforcement,Elevated slabs,10 mm to 25 mm 40.00 12.00 1.800 28.889 6.667

032 107-0500 Grade 60,Reinforcement,Footings 10 mm to 25 mm 40.00 12.00 1.400 37.143 8.571

032 107-0550 Grade 60,Reinforcement,Footings 25 mm to 40 mm 40.00 12.00 1.800 28.889 6.667

032 107-0600 Grade 60,Reinforcement,Slab on grade 10 mm to 25 mm 40.00 12.00 1.600 32.500 7.500

032 107-0700 Grade 60,Reinforcement,Walls,10 mm to 25 mm 40.00 12.00 1.800 28.889 6.667

032 107-0750 Grade 60,Reinforcement,Walls, 25 mm to 40 mm 40.00 12.00 2.200 23.636 5.455

032 107-1000 Grade 60,Reinforcement,Typical in place,10 metric ton lots,average 40.00 12.00 1.100 47.273 10.909

032 107-1100 Grade 60,Reinforcement,Typical in place,over 45 metric ton lots,average 40.00 12.00 1.400 37.143 8.571

0.25 Skilled Foreman

4.00 Steel Fixtures(Reinf.)
2.00 Laborers
MET.
032 107-2000 Unloading,handling & sorting,steel reinforcement add to above TON
0.50 Equip. Oper(Crane) 58.00 8.00 80.000 0.725 0.100
0.50 Equip. Oper. Oiler
0.50 Hyd.Crane,23 ton
0.50 Bed Truck

0.125 Steel Forman

032 107-2400 Reinforcement steel,Dowels, 600 mm long, deformed,10 mm bar EA 2.000 Steel Fixtures 25.00 0.00 400.000 0.063 0.000
1.000 Helper

032 107-2420 Reinforcement steel,Dowels, 600 mm long, deformed,16 mm bar 25.00 0.00 300.000 0.083 0.000

032 107-2430 Reinforcement steel,Dowels, 600 mm long, deformed, 20 mm bar 25.00 0.00 270.000 0.093 0.000

032 107-2450 Reinforcement steel,Dowels,heavier and longer than 20 mm KG 25.00 0.00 280.000 0.089 0.000

032 107-2500 Reinforcement steel,Smooth dowels, 300 mm long, 10 mm dia. (3/8") EA 25.00 0.00 100.000 0.250 0.000

032 107-2520 Reinforcement steel,Smooth dowels, 300 mm long, 16 mm dia. (5/8") 25.00 0.00 85.000 0.294 0.000

032 107-2700 Reinforcement steel,Dowel caps, 125 mm long, 20 mm dia. (3/4") 25.00 0.00 78.000 0.321 0.000

032 107-2720 Reinforcement steel,Dowel caps, 125 mm long, 32 mm dia. (1 1/4") 25.00 0.00 700.000 0.036 0.000
SPLICING REINFORCING BARS Incl. holding bars in
032 109
place while splicing:
1.00 Skilled Foreman
4.00 Steel Fixtures(Reinf.)
032 109-0130 Butt weld column bar splice including holding bars in place, 35 mm bars EA
2.00 Laborers
56.00 16.00 70.000 0.800 0.229
1.00 Power Tools

032 109-0310 Column splice clamps,sleeve&wedge,or end bearing 30 mm or 35 mm steel bars 56.00 16.00 120.000 0.467 0.133
Mechanical but splice, sleeve type with filler metal,compression
032 109-0800 56.00 16.00 55.000 1.018 0.291
only,all grades, columns only 35 mm steel bars
032 109-1700 Splice steel bar,including mechanical threading,straight steel bars, 35 mm 56.00 16.00 60.000 0.933 0.267
1.00 Skilled Foreman
4.00 Steel Fixtures(Reinf.)
032 109-1750 Splice steel bar,including mechanical threading,straight steel bars, 40 mm EA
2.00 Laborers
56.00 16.00 45.000 1.244 0.356
1.00 Power Tools

032 109-2500 Splice bent steel bar, including mechanical threading, bars, 40 mm " " 56.00 16.00 36.000 1.556 0.444

032 200 WELDED WIRE FABRIC:

032 207 WELDED WIRE FABRIC:
0.125 Steel Forman
032 207-0100 Welded Wire Fabric Sheets,100 mm x100 mmx (10x10) mm,12.34 Kg/m2 SQM 4.00 Steel Fixtures 49.00 0.00 630.000 0.078 0.000
2.00 Helper

032 207-0150 Welded Wire Fabric Sheets,100 mm x 200 mm x (12x8) mm,10.90 Kg/m2 52.00 0.00 585.000 0.084 0.000

032 207-0200 Welded Wire Fabric Sheets,100 mm x 200 mm x (10x8) mm, 8.14 Kg/m2 52.00 0.00 560.000 0.088 0.000

032 207-0300 Welded Wire Fabric Sheets, 200 mm x 200 mm x (10x10) mm, 6.6 kg/m2 52.00 0.00 535.000 0.092 0.000

032 207-0400 Welded Wire Fabric Sheets,100 mm x 100 mm x (7x7) mm, 6.04 Kg/m2 52.00 0.00 520.000 0.094 0.000

032 207-0420 Welded Wire Fabric Sheets, 150 mm x 150 mm x (8x8) mm, 5.36 Kg/m2 52.00 0.00 500.000 0.098 0.000

032 207-0420 Welded Wire Fabric Sheets,100 mm x 300 mm x (8x8) mm, 5.30 Kg/m2 52.00 0.00 495.000 0.099 0.000

032 207-0440 Welded Wire Fabric Sheets,100 mm x 400 mm x ( 8x5) mm, 4.34 Kg/m2 52.00 0.00 470.000 0.104 0.000

032 207-0500 Welded Wire Fabric Sheets, 200 mm x 200 mmx ( 8x8) mm, 3.95 Kg/m2 52.00 0.00 450.000 0.109 0.000

032 207-0600 Welded Wire Fabric Sheets,100 mm x 400 mm x ( 6x5) mm, 2.61 Kg/m2 52.00 0.00 425.000 0.115 0.000

032 2070-650 Welded Wire Fabric Sheets,100 mm x 400 mm x ( 4x4) mm, 1.98 Kg/m2 52.00 0.00 420.000 0.117 0.000

032 207-0700 Welded Wire Fabric Sheets, 200 mm x 200 mm x (5x5) mm, 1.54 Kg/m2 52.00 0.00 410.000 0.120 0.000

032 207-0800 Welded Wire Fabric Sheets,150 mm x150 mm x (4x4) mm, 1.35 Kg/m2 52.00 0.00 400.000 0.123 0.000

032 300 STRESSING TENDONS:

032 307 PRESTRESSING STEEL Post-tensioned in field:
1.00 Skilled Foreman
4.00 Steel Fixtures (reinf.)
1.00 Equip.Oper.(light)
032 307-0100 Stressing Tendon,Post-tensioned in field,grouted strand, 15 m span, 50 metric ton KG
2.00 Laborers
64.00 28.00 360.000 0.178 0.078
3.00 Stressing Equipment
0.50 Grouting Equipment

032 307-0150 Stressing Tendon,Post-tensioned in field, grouted strand,15 m span,150 metric ton 64.00 28.00 760.000 0.084 0.037
032 307-0300 Stressing Tendon,Post-tensioned in field,grouted strand, 30 m span,grouted 50 metric ton 64.00 28.00 550.000 0.116 0.051
032 307-1000 Stressing Tendon,Post-tensioned in field,grouted strand, 25 m span,grouted 25 metric ton 64.00 28.00 900.000 0.071 0.031
1 Skilled Foreman
032 307-1200 Stressing Tendon,Post-tensioned in field,ungrouted strand, 15 m span, 50 metric ton 3 Steel workers 32.00 24.00 350.000 0.091 0.069
3 Stressing Equipment
032 307-1400 Stressing Tendon,Post-tensioned in field,ungrouted strand, 30 m span,ungrouted 50 metric ton 32.00 24.00 490.000 0.065 0.049
032 307-1800 Stressing Tendon,Post-tensioned in field,ungrouted bars, 15 m span, 25 metric ton 32.00 24.00 410.000 0.078 0.059
032 307-2000 Stressing Tendon,Post-tensioned in field,ungrouted bars, 25 m span,ungrouted, 25 metric ton 32.00 24.00 515.000 0.062 0.047
032 307-2220 Steel Post-tensioned in field,ungrouted single strand, 30 m slab,10 metric ton 32.00 24.00 325.000 0.098 0.074

033 CAST-IN-PLACE CONCRETE

033 100 STRUCTURAL CONCRETE:
CONCRETE IN PLACE:
033 130
Including forms (5 use),reinforcing steel,and finishing unless otherwise indicated

Page 65
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

0.125 Laborer Forman

2.000 Cement Finishers
1.000 Carpenter
033 130-0204 Cast in Place, with forms,steel & finishing, Base,granolithic, 25 mm x 127mm high, straight LM
1.000 Steel fixer
41.00 16.00 75.000 0.547 0.213
1.000 Common Laborer
2.000 Gas Finishing Mach.

033 130-0220 Cast in Place, with forms,steel & finishing, Base,granolithic, 25 mm x 127mm high,cove " " 41.00 16.00 56.000 0.732 0.286

1.000 Skilled Foreman

10.00 Carpenters &
Steel Fixers (reinf.)
4.000 Laborers
0.250 Cement Finisher
1.000 Equip. Oper
033 130-0300 Cast in Place, with forms,steel & finishing,Beams, 745 kg/m, 3 m span CUM
0.375 Gas Engine Vibrator
130.00 41.00 5.000 26.000 8.200
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
4.000 Power tools

033 130-0350 Cast in Place, with forms,steel & finishing,Beams, 745 kg/m, 7.6 m span " " 130.00 41.00 6.200 20.968 6.613

1.000 Skilled Foreman

10.00 Carpenters &
Steel Fixers (reinf.)
4.000 Laborers
0.250 Cement Finisher
Cast in place with forms,steel,Columns,square, 300 mm x 300 mm, 1.000 Equip. Oper
033 130-0720 CUM 130.00 41.00 2.700 48.148 15.185
Average reinforcing, 4.2 m high 0.375 Gas Engine Vibrator
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
4.000 Power tools

Cast in place with forms,steel,Columns,square, 600 mm x 600 mm,

033 130-0920 130.00 41.00 4.600 28.261 8.913
Average reinforcing, 4.2 m high
Cast in place with forms,steel,Columns,square, 900 mm x 900 mm,
033 130-1020 130.00 41.00 5.900 22.034 6.949
Average reinforcing, 4.2 m high
Cast in place with forms,steel,Columns,square, 300 mm x 1600 mm,
033 130-1040 130.00 41.00 4.500 28.889 9.111
Average reinforcing, 4.2 m high

1.000 Skilled Foreman

9.00 Carpenters & Steel
Fixers(reinf.)
5.000 Laborers
0.250 Cement Finisher
Cast in place including forms, steel & concrete, columns, round, tied, 300 mm 1.000 Equip. Oper
033 130-1100 130.00 25.00 4.000 32.500 6.250
diameter, Average reinforcement, 4.2 m high. 0.375 Gas Engine Vibrator
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
2.000 Power tools

Cast in place with forms,steel,Columns,round,tied, 600 mm diameter,

033 130-1420 130.00 25.00 6.000 21.667 4.167
Average reinforcing, 4.2 m high.
Cast in place with forms,steel,Columns,round,tied, 900 mm diameter,
033 130-1520 130.00 25.00 8.200 15.854 3.049
Average reinforcing, 4.2 m high.
Cast in place with forms,steel,Columns,round,tied,900mm diameter,
033 130-1540 130.00 25.00 4.800 27.083 5.208
Maximum reinforcing, 4.2 m high.

1.000 Skilled Foreman

10.00 Carpenters&Steel
Fixers(reinf.)
4.000 Laborers
0.250 Cement Finisher
Cast in place with forms,steel & finish,Elevated flat slabs, 600 kg/m2 1.000 Equip. Oper
033 130-1900 130.00 41.00 14.700 8.844 2.789
Sup.Load, 6 m span 0.375 Gas Engine Vibrator
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
4.000 Power tools

Cast in place with forms,steel & finish,Elevated flat slabs, 600 kg/m2
033 130-1930 130.00 41.00 20.000 6.500 2.050
Sup.Load, 8.4 m span
Cast in place with forms,steel & finish,Elevated flat slabs, 600 kg/m2
033 130-2100 130.00 41.00 15.000 8.667 2.733
Sup.Load,4.6 m span
Cast in place with forms,steel & finish,Elevated flat slabs, 600 kg/m2
033 130-2130 130.00 41.00 18.000 7.222 2.278
Sup.Load, 7.4 m span

1.000 Skilled Foreman

10.00 Carpenters&Steel
Fixers(reinf.)
4.000 Laborers
0.250 Cement Finisher
Cast in place with forms,steel & finish,Elevated Waffle slabs, 762mm domes, 1.000 Equip. Oper
033 130-2300 130.00 41.00 12.000 10.833 3.417
600 kg/m2 Sup. Load, 6 m span 0.375 Gas Engine Vibrator
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
4.000 Power tools

Cast in place with forms,steel & finish,Elevated Waffle slabs, 762mm domes,
033 130-2350 130.00 41.00 15.000 8.667 2.733
600 kg/m2 Sup. Load, 9.2 m span
Cast in place with forms,steel & finish,Elevated joist slab, 762 mm pans 600 kg/m2 Sup. Load, 4.6 m
033 130-2500 130.00 41.00 11.800 11.017 3.475
span
Cast in place with forms,steel & finish,Elevated joist slab, 762 mm pans 600 kg/m2 Sup. Load, 7.2 m
033 130-2750 130.00 41.00 14.400 9.028 2.847
span
033 130-2780 Cast in place with forms,steel & finish,Elevated One way beam slab, 600 kg/m2 Sup. Load, 7.6 m span 130.00 41.00 9.500 13.684 4.316

033 130-2950 Cast in place with forms,steel & finish,Elevated Two way beam slab, 600 kg/m2 Sup. Load, 7.6 m span 130.00 41.00 10.950 11.872 3.744

0.50 Skilled foreman

6.00 Laborers
2.00 Cement Fisnishers
Cast in place, Elevated slabs including finish only, not including forms or reinforcing:Regular Concrete, 2.00 Carpenters
033 130-3200 SQM 92.00 40.00 438.000 0.210 0.091
150 mm slab 1.00 Equip. Operator
1.00 Concrete Pump (small)
2.00 Gas engine vibrator
2.00 Gas Finishing Machine

033 130-3300 Cast inplace,Lightweight concrete elevated slabs including finish only,1750 kg/m3, 64 mm thick floor fill ,, " 92.00 40.00 438.000 0.210 0.091

1.000 Skilled Foreman

5.000 Carpenters &
Steel Fixers (reinf
0.25 Cement Finisher
4.000 Laborers
033 130-3800 Cast in place including forms & steel, Spread footings, spread under 0.75 m3 CUM 0.250 Equip.Operators 84.00 23.00 15.000 5.600 1.533
0.375 Gas Enginge Vibrator
0.25 Crane 35 Ton
0.125 Truck
0.125 Concrete Pump
2.00 Power Tool

033 130-3850 Cast in place including forms & steel, Spread footings, spread over 4 m3 " 84.00 23.00 18.000 4.667 1.278

0.50 Skilled Foreman

7.000 Carpenters &
Steel Fixers (reinf)
0.250 Cement Finisher
4.000 Laborers
033 130-4050 Cast in place, Raft ( Matt ) foundation, including forms & steel, over 1000 m3 0.500 Equip.Operators 98.00 23.00 24.500 4.000 0.939
0.250 Gas Enginge Vibrator
0.250 Crane 35 Ton
0.250 Truck
0.125 Concrete Pump
2.000 Power Tool

033 130-4050 Cast in place, Raft ( Matt ) foundation, including forms & steel, over 25 m3 & up to 500 m3 98.00 23.00 20.000 4.900 1.150
033 130-4050 Cast in place, Raft ( Matt ) foundation, including forms & steel, up to 25 m3 98.00 23.00 18.000 5.444 1.278

0.5 Skilled Foreman

10.00 Carpenters &Steel
Fixers (reinf.)
5.000 Laborers
0.250 Cement Finisher
1.000 Equip. Oper
033 130-4200 Cast in place including forms & steel,Grade walls, 200 mm thick, 2400m m high 0.250 Gas Engine Vibrator
134.00 41.00 8.700 15.402 4.713
0.125 Concrete Pump &Trans
Mixer
0.625 Crane 80 Ton
0.125 Truck
4.000 Power tools

033 130-4250 Cast in place including forms & steel,Grade walls, 200 mm thick, 4.2 m high 134.00 41.00 7.000 19.143 5.857

033 130-4270 Cast in place including forms & steel,Grade walls, 300 mm thick, 4.2 m high 134.00 41.00 10.000 13.400 4.100

033 130-4350 Cast in place including forms & steel,Grade walls, 400 mm thick, 3.6 m high 134.00 41.00 15.000 8.933 2.733

033 130-4500 Cast in place including forms & steel,Grade walls, 400 mm thick, 5.5 m high 134.00 41.00 10.400 12.885 3.942
Cast in place including forms, steel & finish, Handicap access ramp,
033 130-4525 134.00 41.00 14.500 9.241 2.828
railing both sides, 1.50 m wide

1.00 Skilled foreman

6.00 Carpenters &
Steel Fixtures(reinf.)
3.00 Laborers
3.00 Cement Finishers
033 130-4700 Cast in place including forms,steel and finish, Slab on grade, 150 mm thick 0.125 Equp. Operators (med.)
113.00 46.00 12.000 9.417 3.833
0.375 Concrete Pump (small)
2.000 Power tools
0.375 Gas Engine Vibrator
3.00 Gas Finishing Machine

0.50 Skilled foreman

1.00 Laborers
Cast in place,Slab on grade,including troweled finish,not incl.forms 3.00 Cement Fisnishers
033 130-4760 SQM 34.00 28.00 100.000 0.340 0.280
or reinforcing, 100mm thick slab 0.25 Concrete Pump (small)
0.25 Gas engine vibrator
3.00 Gas Finishing Machine

0.50 Skilled foreman

1.00 Laborers
Cast in place,Slab on grade,including troweled finish,not incl.forms 3.00 Cement Fisnishers
033 130-4840 34.00 28.00 88.440 0.384 0.317
or reinforcing, 200 mm thick slab 0.25 Concrete Pump (small)
0.25 Gas engine vibrator
3.00 Gas Finishing Machine

Cast in place,Slab on grade,including troweled finish,not incl.forms

033 130-4900 34.00 28.00 77.660 0.438 0.361
or reinforcing, 300 mm thick slab

Page 66
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS
Cast in place, Slab on grade,including troweled finish,not incl.forms
033 130-4950 34.00 28.00 70.770 0.480 0.396
or reinforcing, 380 mm thick slab
Cast in place,Slab on grade,incl. textured finish,not inc. forms
033 130-5010 34.00 28.00 90.280 0.377 0.310
or reinforcing, 150 mm thick slab
Cast in place Lightweight concrete, ready mix 1:3:2,for roof decks, including screed finish only, not
033 130-5650 CUM 34.00 28.00 30.000 1.133 0.933
including forms or reinforcing

1.000 Skilled foreman

6.000 Carpenters & Steel
Fixtures (reinf.)
3.000 Laborers
Cast in place,Slab on grade,including troweled finish,forms 3.000 Cement Finishers
033 130-5700 113.00 46.00 9.000 12.556 5.111
and reinforcing, 100mm thick slab 0.125 Equip. Operators (med.)
0.375 Concrete Pump (small)
2.000 Power tools
0.375 Gas Engine Vibrator
3.000 Gas Finishing Machine

Cast in place,Slab on grade,including troweled finish,forms

033 130-5720 113.00 46.00 17.200 6.570 2.674
and reinforcing, 200mm thick slab
Cast in place,Slab on grade,including troweled finish,forms
033 130-5740 113.00 46.00 24.800 4.556 1.855
and reinforcing, 300mm thick slab
Cast in place,Thickened Slab on grade,including troweled finish,forms
033 130-5760 113.00 46.00 30.500 3.705 1.508
and reinforcing, 380mm thick slab

1.000 Skilled Foreman

5.00 Carpenters &
Steel Fixers (reinf.)
4.000 Laborers
0.250 Cement Finisher
033 130-5950 Cast in place concrete, Pile caps,forms and reinf.,square or rectangular.,over 7.5 m3 CUM 0.250 Equip. Oper 84.00 23.00 21.000 4.000 1.095
0.375 Gas Engine Vibrator
0.250 Crane 35 Ton
0.125 Truck
0.125 Concrete Pump
2.000 Power tools

Cast in place concrete, Pile caps,forms and reinf.,

033 130-6050 " 84.00 23.00 20.500 4.098 1.122
Triangular or hexagonal, over 7.5 m3

1.000 Skilled Foreman

9.000 Carpenters
5.000 Laborers
0.500 Cement Finisher
Cast in place concrete, Retaining walls,gravity, 1.2 m high including forms & reinforcement, tapered 200
033 130-6200 0.500 Equip. Oper 128.00 42.00 15.500 8.258 2.710
mm top, 600 mm bottom 0.375 Gas Engine Vibrator
0.375 Concrete Pump (small)
0.500 Crane 80 Ton
4.00 Power tools

0.500 Skilled Foreman

10.00 Carpenters & Steel Fixers
(reinf.)
5.000 Laborers
0.250 Cement Finisher
Cast in place concrete, Retaining walls, cantilever, 2.4 m high including forms, footing and 1.000 Equip. Oper
033 130-6300 134.00 41.00 15.000 8.933 2.733
reinforcement, tapered 300 mm top, 600 mm bottom. 0.250 Gas Engine Vibrator
0.125 Concrete Pump &Trans
Mixer
0.625 Crane 80 Ton
0.125 Truck
4.000 Power tools

1.000 Skilled Foreman

8.000 Carpenters
0.250 Steel Fixers
0.125 Cement Finishers
0.125 Equp. Operators
Cast in place concrete, Stairs free standing,treads 1.8 meter long, 300 mm wide, 4.000 Laborers
033 130-6800 108.00 39.00 1.110 97.297 35.135
including forms,steel , landing 1.2 x 1.8 meters and finish. 0.125 Gas Engine Vibrator
0.125 Concrete pump
0.375 Crane 80 Ton
0.125 Truck
0.125 Gas finishing m/c
4.000 Power tools

1.000 Skilled Foreman

10.00 Carpenters & Steel Fixers
(reinf.)
4.000 Laborers
0.250 Cement Finisher
1.000 Equip. Oper
033 130-7000 Cast in place concrete, Stairs Landing, including forms,steel & finish 0.375 Gas Engine Vibrator
130.00 41.00 10.700 12.150 3.832
0.125 Concrete Pump &Trans
Mixer
0.500 Crane 80 Ton
0.125 Truck
4.000 Power tools

033 138 CUTTING CONCRETE See Div. 020-728

033 142 DAMPPROOFING See Div. 071
033 146 EQUIPMENT FOR PLACING CONCRETE See Div. 016-406
033 148 EXPANSION JOINT See Div. 031-132
033 134 CURING:
033 134-0100 Curing concrete with burlap,4 uses assumed 340 gram SQM 2 Common Laborers 16.00 0.00 450.000 0.036 0.000

033 134-0200 Curing concrete with waterproof curing paper, 2 ply,reinforced 16.00 0.00 575.000 0.028 0.000

033 134-0300 Curing concrete with sprayed membrane curing compound 16.00 0.00 700.000 0.023 0.000

033 156 GROUT:

1 Cement Finisher
033 156-0010 Grout Column & machine bases,non-shrink metallic grout, 25 mm deep SQM
1 Helper
16.00 0.00 5.500 2.909 0.000

033 134-0050 Grout Column & machine bases,non-shrink metallic grout, 50 mm deep " " 16.00 0.00 4.000 4.000 0.000

033 160 GUNITE OR "SHOTCRETE":

0.125 Labor Foreman
4.000 Laborers
2.000 Cement Finishers
1.000 Equip. Oper.(med.)
033 160-0300 Gunite,applied in 25mm layers,typical in place,including mesh, 50 mm thick,average SQM
2.000 Steel Workers (reinf.)
73.00 10.00 40.000 1.825 0.250
1.000 Concrete Pump (small)
0.125 Crane 80 Ton
0.125 Truck

033 160-0500 Gunite,applied in 25mm layers,typical in place,including mesh, 100 mm thick,average 73.00 10.00 30.000 2.433 0.333
033 160-1100 Gunite,applied in 25mm layers,typical in place,including mesh,100 mm thick,high finish,average 73.00 10.00 20.000 3.650 0.500
033 168 PATCHING CONCRETE:
1.000 Cement Finisher
033 168-0100 Patching concrete in Floors, 6 mm thick, small areas,regular grout SQM 1.000 Helper 16.00 8.00 20.000 0.800 0.400
1.000 Tool set

1.000 Cement Finisher

033 168-0150 Patching concrete in Floors, 6 mm thick, small areas,epoxy grout SQM 1.000 Helper 16.00 8.00 15.000 1.067 0.533
1.000 Tool set

033 168-2150 Patching concrete in Walls,including chipping,cleaning and epoxy grout Average " " 16.00 8.00 6.000 2.667 1.333

033 172 PLACING CONCRETE and vibrating,including labor & eqpt.:

1 Labor Foreman
9 Laborers
1 Cement Finisher
033 172-0050 Placing concrete,including vibrating,labor & equipment for small beams,elevated,pumped CUM 2 Carpenter 104.00 24.00 80.000 1.300 0.300
1 Equip. Operator
2 Gas Engine Vibrator
1 Concrete Pump & Trans Mixer

1 Labor Foreman
5 Laborers
1 Cement Finisher
1 Carpenter
033 172-0100 Placing concrete,including vibrating,labor & equipment for small beams,elevated,with crane and bucket 1 Equip. Oper.
72.00 24.00 42.000 1.714 0.571
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
9 Laborers
1 Cement Finisher
033 172-0200 Placing concrete,including vibrating,labor & equipment for large beams,elevated,pumped 2 Carpenter 104.00 24.00 87.000 1.195 0.276
1 Equip. Operator
2 Gas Engine Vibrator
1 Concrete Pump & Trans Mixer

Placing concrete,including vibrating,labor & equipment for columns,square or round,300mm

033 172-0400 " 72.00 24.00 28.000 3.714 0.857
thick,pumped

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for columns,square or round, 300 mm thick, with 1 Carpenter
033 172-0450 72.00 24.00 28.000 2.571 0.857
crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for columns,square or round, 600 mm
033 172-0800 1 Carpenter 72.00 24.00 54.000 1.333 0.444
thick,pumped 1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for columns,square or round, 1 Carpenter
033 172-0850 72.00 24.00 46.000 1.565 0.522
600 mm thick, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for columns,square or round, 900 mm
033 172-1000 1 Carpenter 72.00 24.00 104.000 0.692 0.231
thick,pumped 1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

Page 67
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for columns,square or round, 1 Carpenter
033 172-1050 72.00 24.00 81.000 0.889 0.296
900 mm thick, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
9 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for elevated slabs,less than
033 172-1400 2 Carpenter 104.00 24.00 87.000 1.195 0.276
150 mm thick,pumped 1 Equip. Operator
2 Gas Engine Vibrator
1 Concrete Pump & Trans Mixer

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for elevated slabs,less than 150 mm thick, with 1 Carpenter
033 172-1450 72.00 24.00 60.000 1.200 0.400
crane & bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
9 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for elevated slabs,150 mm to 250 mm
033 172-1500 2 Carpenter 104.00 24.00 105.000 0.990 0.229
thick,pumped 1 Equip. Operator
2 Gas Engine Vibrator
1 Concrete Pump & Trans Mixer

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for elevated slabs over 250 mm thick, with crane 1 Carpenter
033 172-1650 CUM 72.00 24.00 69.000 1.043 0.348
& bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
5 Laborers
033 172-1900 Placing concrete,including vibrating,labor & equipment for footings, continous,shallow,direct chute 1 Carpenter 64.00 16.00 93.000 0.688 0.172
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-1950 Placing concrete,including vibrating,labor & equipment for footings, continous,shallow,pumped 1 Carpenter 72.00 24.00 71.000 1.014 0.338
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for footings, continuous, 1 Carpenter
033 172-2000 72.00 24.00 66.000 1.091 0.364
shallow, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
5 Laborers
Placing concrete,including vibrating,labor & equipment for footings, Deep continuous footings,direct
033 172-2100 1 Carpenter 64.00 16.00 112.000 0.571 0.143
chute 1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-2150 Placing concrete,including vibrating,labor & equipment for footings, Deep continuous footings,pumped 1 Carpenter 72.00 24.00 93.000 0.774 0.258
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
033 172-2600 Placing concrete,including vibrating,labor & equipment for spread footings,over 4 m3, direct chute 1 Carpenter 64.00 16.00 87.000 0.736 0.184
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-2650 Placing concrete,including vibrating,labor & equipment for spread footings,over 4 m3, pumped 1 Carpenter 72.00 24.00 85.000 0.847 0.282
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for spread footings,over 4 m3, 1 Carpenter
033 172-2700 72.00 24.00 70.000 1.029 0.343
with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for foundation mats, over
033 172-2950 1 Carpenter 72.00 24.00 233.000 0.309 0.103
1000 m3, pumped 1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for foundation mats, 1 Carpenter
033 172-3000 72.00 24.00 100.000 0.720 0.240
over 1000 m3, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
5 Laborers
033 172-3200 Placing concrete,including vibrating,labor & equipment for grade,beams,direct chute 1 Carpenter 64.00 16.00 112.000 0.571 0.143
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-3250 Placing concrete,including vibrating,labor & equipment for grade,beams,pumped 1 Carpenter 72.00 24.00 105.000 0.686 0.229
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for grade, 1 Carpenter
033 172-3300 72.00 24.00 100.000 0.720 0.240
beams, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for high rise, more than 1 Carpenter
033 172-3500 CUM 90.000 0.800 0.356
5 stories & up to 15 stories, pumped, adds/story 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

Placing concrete,including vibrating,labor & equipment for high rise,

033 172-3510 95.000 0.758 0.000
more than 5 stories, with crane and bucket adds/story
Placing concrete,including vibrating,labor & equipment for high rise, more than
033 172-3520 110.000 0.655 0.040
15 stories, pumped, adds/story
Placing concrete,including vibrating,labor & equipment for high rise, more than 15 stories, with crane
033 172-3510 115.000 0.626 0.040
and bucket adds/story
1 Labor Foreman
5 Laborers
033 172-4000 Placing concrete,including vibrating,labor & equipment for pile cap,over 8m3 direct chute 1 Carpenter 64.00 16.00 140.000 0.457 0.114
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-4050 Placing concrete,including vibrating,labor & equipment for pile cap,over 8m3 pumped 1 Carpenter 72.00 24.00 116.000 0.621 0.207
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
1 Carpenter
033 172-4100 Placing concrete,including vibrating,labor & equipment for pile cap,over 8m3 with crane and bucket 1 Equip. Oper.
72.00 24.00 100.000 0.720 0.240
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor Foreman
5 Laborers
033 172-4600 Placing concrete,including vibrating,labor & equipment for slab over 150 mm thick, direct chute 1 Carpenter 64.00 16.00 116.000 0.552 0.138
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-4650 Placing concrete,including vibrating,labor & equipment for slab over 150 mm thick, pumped 1 Carpenter 72.00 24.00 116.000 0.621 0.207
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
Placing concrete,including vibrating,labor & equipment for slab over 1 Carpenter
033 172-4700 72.00 24.00 100.000 0.720 0.240
150 mm thick, with crane and bucket 1 Equip. Oper.
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

Page 68
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

1 Labor Foreman
5 Laborers
033 172-4900 Placing concrete,including vibrating,labor & equipment for walls, 200 mm thick, direct chute 1 Carpenter 64.00 16.00 70.000 0.914 0.229
1 Cement Finisher
2 Gas Engine Vibrators

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-4950 Placing concrete,including vibrating,labor & equipment for walls, 200 mm thick, pumped 1 Carpenter 72.00 24.00 76.000 0.947 0.316
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
1 Carpenter
033 172-5000 Placing concrete,including vibrating,labor & equipment for walls, 200 mm thick, with crane and bucket 1 Equip. Oper.
72.00 24.00 66.000 1.091 0.364
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

1 Labor foreman
5 Laborers
1 Cement Finisher
033 172-5100 Placing concrete,including vibrating,labor & equipment for walls, 300 mm thick, pumped 1 Carpenter 72.00 24.00 77.000 0.935 0.312
1 Equip.Oper.(med.)
2 Gas Engine Vibrators
1 Concrete Pump (small)

1 Labor Foreman
5 Laborers
1 Cement Finisher
1 Carpenter
033 172-5400 Placing concrete,including vibrating,labor & equipment for walls, 400 mm thick,with crane and bucket 1 Equip. Oper.
72.00 24.00 60.000 1.200 0.400
2 Gas Engine Vibrators
1 Concrete Bucket,0.76m3
1 Hyd.Crane,50 metric ton

0.125 Labor Foreman

Add to above concrete placing items and as required for concrete dumping
033 172-5810 1.00 Laborers 9.00 8.00 40.000 0.225 0.200
using wheeled riding carts, 45 meter haul. 1.00 Concrete Wheeled Carts.

033 180 SAWING CONCRETE See division 020-728

033 184 STAIR TREAD INSERTS:
033 184-0010 Stair tread inserts, cast iron,abrasive, 75 mm wide LM 1 Carpenter 8.00 0.00 20.000 0.400 0.000

033 184-0550 Stair tread inserts,cast iron,extruded aluminum safety tread,100 mm wide LM 1 Carpenter 8.00 0.00 18.000 0.444 0.000

033 184-1750 Stair tread,cement filled pan type,non-slip SQM 1 Cement finisher 8.00 0.00 7.000 1.143 0.000

033 192 WATERPROOFING AND DAMPPROOFING See division 071

033 450 CONCRETE FINISHING:
033 454 FINISHING FLOORS:
033 454-0010 Finishing concrete floors monolithic,screed finish SQM 1 Cement Finisher 8.00 0.00 70.000 0.114 0.000
0.125 Labor Foreman
033 454-0100 Finishing concrete floors,float finish 1 Cement Finisher 9.00 8.00 55.000 0.164 0.145
1 Gas Finishing Mach.

033 454-0150 Finishing concrete floors,Broom finish 9.00 8.00 50.000 0.180 0.160

033 454-0200 Finishing concrete floors,Steel trowel finish,for resilient tile 9.00 8.00 45.000 0.200 0.178

033 454-0250 Finishing concrete floors monolithic,Steel trowel finish. 9.00 8.00 36.000 0.250 0.222
0.125 Labor Foreman
1 Laborer
033 454-0600 Concrete,Integral topping and finish, using 1:1:2 mix, 25mm thick 2 Cement Finishers
25.00 16.00 55.000 0.455 0.291
2 Gas Finishing Mach.

033 454-0950 Concrete,Granolithic topping,laid after,1:1:1-1/2 mix, 50 mm thick 25.00 16.00 40.000 0.625 0.400
033 454-1200 Concrete,Granolithic topping Heavy duty,1:1:2, 20 mm thick, preshrunk,gray,over 2000 m2 25.00 16.00 25.000 1.000 0.640
033 454-1350 Concrete,Granolithic topping,for colors, 2.44 kg/m2, add, Average 25.00 16.00 115.000 0.217 0.139

033 454-1600 Concrete,Exposed local aggregate finish, Average 1 Cement finisher 8.00 0.00 45.000 0.178 0.000
0.25 Labor Foreman
033 454-2000 Concrete,Floor hardeners, metallic,light service, 2.44 kg/m2 1 Cement Finisher 10.00 8.00 68.000 0.147 0.118
1 Gas Finishing Mach.

033 454-2050 Concrete,Floor hardeners, metallic,Medium service, 3.66 kg/m2 10.00 8.00 60.000 0.167 0.133

033 454-2100 Concrete,Floor hardeners, metallic,Heavy service, 4.88 kg/m2 10.00 8.00 52.000 0.192 0.154
0.25 Labor Foreman
033 454-2150 Concrete,Floor hardeners, metallic,Extra Heavy service, 7.32 kg/m2 SQM 1 Cement Finisher 10.00 8.00 45.000 0.222 0.178
1 Gas Finishing Mach.

033 454-2300 Concrete,Floor hardeners,Non-metallic,light service, 2.44 kg/m2 10.00 8.00 68.000 0.147 0.118

033 454-2450 Concrete,Floor hardeners,Non-metallic, Extra Heavy, 7.32 kg/m2 10.00 8.00 45.000 0.222 0.178

033 454-2600 Concrete,Floor colored hardener,metallic,medium service 3.66 kg/m2 10.00 8.00 35.000 0.286 0.229

033 454-2650 Concrete,Floor colored hardener,non-metallic,medium service 3.66 kg/m2 10.00 8.00 45.000 0.222 0.178

033 454-3850 Concrete floor Dustproofing,silicate liquids, 2 coats 1 Cement finisher 8.00 0.00 100.000 0.080 0.000

033 454-4000 Concrete floor,Dustproofing,Epoxy coating, 1 coat, clear 8.00 0.00 115.000 0.070 0.000

033 454-4050 Concrete floor,Dustproofing,Epoxy coating, 1 coat,Colors 8.00 0.00 115.000 0.070 0.000

033 454-4400 Concrete Stair finish,float 8.00 0.00 20.000 0.400 0.000

033 454-4500 Concrete Stair finish,Steel trowel finish 8.00 0.00 15.000 0.533 0.000

033 454-4600 Concrete Stair finish,Silicon carbide finish,1.22 kg/m2 8.00 0.00 10.000 0.800 0.000

033 458 FINISHING WALLS:

1 Cement Finisher
033 458-0050 Finishing Concrete Walls, Burlap rub with grout SQM
1 Helper
16.00 0.00 56.000 0.286 0.000

033 458-0100 Finishing Concrete Walls,Carborundum rub, dry ,, 16.00 0.00 28.000 0.571 0.000
0.25 Labor Foreman
4 Laborers
033 458-0300 Finishing Concrete Walls, Bush hammer,green concrete 1 Equipment Oper.(light) 42.00 8.00 75.000 0.560 0.107
1 Air Compressor,118 L/s W/
Accessories & Hoses

033 458-0600 Finishing Concrete Walls, Float finish, 2 mm thick 1 Cement Finisher 8.00 0.00 22.000 0.364 0.000
0.25 Foreman
1.00 Laborer
033 458-0700 Finishing Concrete Walls, Sandblast,light penetration 2.00 Cement Finishers
26.00 16.00 85.000 0.306 0.188
2.00 Gas Finishing Mach.

033 458-0750 Finishing Concrete Walls, Sandblast,Heavy penetration " 24.00 16.00 28.000 0.929 0.571

034 PRECAST CONCRETE

034 100 STRUCTURAL PRECAST:
034 104 BEAMS:
1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast concrete beams,"L"shaped, 6.0m span, 300 mm x 500 mm, 1 Equip.Oper.(Crane)
034 104-0011 EA 88.00 72.00 25.000 3.520 2.880
and within 25 meter reaching distance 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

Precast concrete beams,"L"shaped, Larger size span beams,

034 104-1050 LM 88.00 72.00 100.000 0.880 0.720
up to 10 ton units and within 25 meters reaching distance.
Precast concrete beams,"L"shaped, Larger size span beams,
034 104-1100 " 88.00 72.00 45.000 1.956 1.600
up to 15 ton and within 45 meters reaching distance.
034 112 COLUMNS:
1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast concrete columns Rectangular to 3.7 m floor high, small columns, 1 Equip.Oper.(Crane)
034 112-0010 LM 88.00 72.00 74.000 1.189 0.973
1 floor, up to 3 ton units and within 30 meters reaching distance. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

Precast concrete columns Rectangular to 3.7 m floor high, large columns,

034 112-0050 88.00 72.00 45.000 1.956 1.600
1 floor, up to 10 ton units and within 30 meters reaching distance.
Precast concrete columns Rectangular to 7.2 m floor high, large columns,
034 112-0300 88.00 72.00 85.000 1.035 0.847
1 floor, up to 5 ton units and within 30 meters reaching distance.
Precast concrete columns Rectangular to 3.7 m floor high, large columns,
034 112-1000 88.00 72.00 30.000 2.933 2.400
1 floor, up to 10 ton units and within 45 meters reaching distance.
Precast concrete columns Rectangular to 3.7 m floor high, large columns,
034 112-1200 88.00 72.00 24.000 3.667 3.000
1 floor, up to 10 ton units and within 60 meters reaching distance.
034 124 CURBS ROADWAY TYPE See Div. 025-250
034 128 JOISTS:
1 Skilled Forman
3 Skilled Workers
Precast Concrete Joists, 195 KG/M2 L.L., 150 mm deep for 3.6 m spans,
034 128-0010 EA 1 Laborer 48.00 8.00 42.000 1.143 0.190
low rise 8 floors building 1 Equip.Oper.(Crane)
1 Hyd.Crane,11 metric ton

Precast Concrete Joists, 195 KG/M2 L.L., 200 mm deep for 4.8 m spans,
034 128-0050 48.00 8.00 31.000 1.548 0.258
low rise 8 floors building
Precast Concrete Joists, 195 KG/M2 L.L., 250 mm deep for 6 m spans,
034 128-0100 48.00 8.00 24.000 2.000 0.333
low rise 8 floors building
Precast Concrete Joists, 195 KG/M2 L.L., 300 mm deep for 7.2 m spans,
034 128-0150 48.00 8.00 20.000 2.400 0.400
low rise 8 floors building
1 Skilled Forman
Precast Concrete Joists, 195 KG/M2 L.L., 150 mm deep for 3.6 m spans,
034 128-0500 3 Skilled Workers 80.00 0.00 19.750 4.051 0.000
2 floor building, labor handling & installation, 50 meter handling distance. 6 Common Laborers
Precast Concrete Joists, 195 KG/M2 L.L., 200 mm deep for 4.8 m spans,
034 128-0550 80.00 0.00 14.800 5.405 0.000
2 floor building, labor handling & installation, 50 meter handling distance.
Precast Concrete Joists, 195 KG/M2 L.L., 150 mm deep for 7.2 m spans,
034 128-0600 80.00 0.00 10.000 8.000 0.000
2 floor building, labor handling & installation, 50 meter handling distance.
034 136 SLABS:

Page 69
DIVISION 03 : CONCRETE
CSI CREW CREW CREW DAILY MAN EQUIP.
ITEM DESCRIPTION UNIT
CODE STRUCTURE HOURES EQUIP. OUTPUT HOURS HOURS

1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast roof slabs, Prestressed hollowcore or plank, 195 Kg/m2 LL, 200 mm deep, 1 Equip.Oper.(Crane)
034 136-0010 SQM 88.00 72.00 600.000 0.147 0.120
Straight jobs without difficulties. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

Precast roof slabs, Prestressed hollowcore or plank, 195 Kg/m2 LL, 200 mm deep,
034 136-0010 88.00 72.00 320.000 0.275 0.225
Jobs with difficulties.
034 136-0200 Precast floor slabs, Prestressed hollowcore or plank, 490 Kg/m2 LL, 250 mm deep 88.00 72.00 520.000 0.169 0.138

034 140 TEES:

1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast prestressed concrete,Double tee, 3 m wide, floor members, 1 Equip.Oper.(Crane)
034 140-0200 SQM 88.00 72.00 648.000 0.136 0.111
18m span;up to 0.8 m deep & up to 390 Kg/m2 LL. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

Precast prestressed concrete,Double tee, 3 m wide, roof members,

034 140-0350 88.00 72.00 540.000 0.163 0.133
15 m span;up to 0.3 m deep.
Precast Concrete,Double tees,floor members standard weight, 0.3 m deep,
034 140-1250 88.00 72.00 288.000 0.306 0.250
2.4 m wide, 6 m span
Precast Concrete,Double tees,floor members standard weight, 0.6 m deep,
034 140-1450 88.00 72.00 468.000 0.188 0.154
2.4 m wide,15 m span
Precast Concrete,Double tees,roof members light weight, 500 mm x 2400 mm wide
034 140-2050 88.00 72.00 489.000 0.180 0.147
12 m span
Precast Concrete,Double tees,roof members, light weight, 0.8 m deep, 3.0 m wide
034 140-2150 88.00 72.00 702.000 0.125 0.103
18 m span
Precast Concrete,Double tees,roof members standard weight, 0.4 m deep, 2.4 m wide
034 140-2250 88.00 72.00 368.000 0.239 0.196
9 m span
Precast Concrete,Double tees,roof members standard weight, 500 mm x 2400 mm wide
034 140-2350 88.00 72.00 432.000 0.204 0.167
12 m span
034 500 ARCHITECTURAL PRECAST:
034 504 WALL PANELS:
1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast Concrete,Wall panel,uninsulated,smooth gray,low rise, size:1.2 m x 2.4 m, 100 mm thick, up to 1 Equip.Oper.(Crane)
034 504-0150 SQM 88.00 8.00 53.000 1.660 0.151
1 ton and within 20 meters reaching distance.. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast Concrete,Wall panel,uninsulated,smooth gray,low rise, size:2.4 m x 2.4 m, 100 mm thick, up to 1 Equip.Oper.(Crane)
034 504-0200 SQM 88.00 8.00 67.000 1.313 0.119
2 tons and within 20 meters reaching distance. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

1 Struc.Steel Foreman
6 Struc.Steel Workers
2 Common Laborer
Precast Concrete,Wall panel,uninsulated,smooth gray,low rise, size:2.4 m x 4.8 m, 100 mm thick, up to 1 Equip.Oper.(Crane)
034 504-0250 SQM 88.00 8.00 109.000 0.807 0.073
3 tons and within 20 meters reaching distance. 1 Equip.Oper.Oiler
1 Truck Crane,136 metric ton
4 Hydraulic Jacks
4 Tools Set

Precast Concrete,Wall panel,uninsulated,smooth gray,low rise, size:2.4 m x 2.4 m,

034 504-0400 88.00 8.00 59.000 1.492 0.136
200 mm thick, up to 2.5 tons and within 20 meters reaching distance.
Precast Concrete,Wall panel,uninsulated,exposed aggregate,low rise, size:2.4 m x 2.4 m,
034 504-0500 88.00 8.00 67.000 1.313 0.119
150 mm thick, up to 2 tons and within 20 meters reaching distance.
Precast Concrete,Wall panel,uninsulated,exposed aggregate,low rise, size:2.4 m x 2.4 m,
034 504-0520 88.00 8.00 59.000 1.492 0.136
200 mm thick, up to 3 tons and within 20 meters reaching distance.
Precast Concrete,Wall panel,insulated,textured, 10 floors high rise, size:1.8 m x 2.4 m, 200 mm thick, up
034 504-0560 88.00 8.00 35.000 2.514 0.229
to 2.5 ton and 20 meters reaching distance.
Precast Concrete,Wall panel,insulated,textured, 10 floors high rise, size:1.8 m x 3.2 m, 200 mm thick, up
034 504-0600 88.00 8.00 53.000 1.660 0.151
to 3 ton and 20 meters reaching distance.
Precast Concrete,Wall panel,insulated,textured,10 floors high rise, size:2.4 m x 4.8 m, 200 mm thick, up
034 504-0700 88.00 8.00 65.000 1.354 0.123
to 5 ton and 20 meters reaching distance.
Precast Concrete,Wall panel,insulated,textured,10 floors high rise, size:2.4 m x 4.8 m, 200 mm thick, up
034 504-0700 88.00 8.00 65.000 1.354 0.123
to 5 ton and 20 meters reaching distance.
034 800 PRECAST SPECIALTIES:
034 802 LINTELS:
0.25 Labor Foreman
034 802-0800 Lintel,Precast concrete,100 mm x 200 mm, to 1500 mm long, low rise LM 1 Bricklayer 18.00 0.00 60.000 0.300 0.000
1 Bricklayer Helper

0.25 Labour Foreman

1 Bricklayer
034 802-0850 Lintel,Precast concrete,100 mm x 200 mm, to 3.6 m long, 5 to 10 floors 2 Bricklayer Helpers 34.00 8.00 55.000 0.618 0.145
1 Equip. Oper.
1 Crane

034 802-1250 Lintel,Precast concrete, 200 mm wide, 200 mm height, to 3.6 m long,over 10 floors. 34.00 8.00 42.000 0.810 0.190

034 802-1400 Lintel,Precast concrete, 250 mm wide, 200 mm height,to 4.3 m long, low rise 34.00 8.00 65.000 0.523 0.123

034 802-1450 Lintel,Precast concrete, 300 mm wide, 200 mm height, to 5.8 m long, 5 to 10 floors. 34.00 8.00 70.000 0.486 0.114

035 CEMENTITIOUS DECKS

035 200 LIGHTWEIGHT CONCRETE:
035 204 CONCRETE CHANNEL SLABS:
0.5 Labor Foreman
3 Carpenters
035 204-0010 Concrete channel slabs 70 mm or 90 mm thick, straight SQM 1 Laborer 44.00 8.00 120.000 0.367 0.067
1 Equip. Oper.(crane)
1 Hyd. Crane,11 metric ton

035 204-0050 Concrete channel slabs 70 mm or 90 mm thick, chopped up 44.00 8.00 65.000 0.677 0.123

035 204-0300 Concrete channel slabs 200 mm thick,span to 7 m 44.00 8.00 85.000 0.518 0.094

035 208 CONCRETE PLANK

0.5 Labor Foreman
3 Carpenters
035 208-0010 Concrete plank lightweight,nailable,T&G, 50 mm thick SQM 1 Laborer 44.00 8.00 170.000 0.259 0.047
1 Equip. Oper.(crane)
1 Hyd. Crane,11 metric ton

035 208-0100 Concrete plank lightweight,nailable,T&G, 95 mm thick " " 44.00 8.00 136.000 0.324 0.059

035 212 INSULATING:

0.5 Labor Foreman
3 Laborers
Roof Insulating, ligtweight cellular concrete roof fill
035 212-0010 CUM 2 Cement Finishers 52.00 8.00 28.000 1.857 0.286
Portland cement and foaming agent 1 Equip.Oper.(med)
1 Concrete Pump (small)

Roof Insulating Poured vermiculite or perlite,field mix,

035 212-0200 52.00 8.00 25.000 2.080 0.320
1:6 roof fill,add formboards above, 50 mm thick
035 212-0250 Roof Insulating,Ready mix,1:6 mix, roof fill, 75 mm thick 52.00 8.00 595.000 0.087 0.013

035 300 WOOD FIBER SYSTEMS

035 304 FORMBOARD:
0.5 Labor foreman
1 Struc. Steel Worker
035 304-0070 Formboard,including sub-purlins non-asbestos,fiber cement, 6 mm thick SQM 1 Welder 28.00 8.00 215.000 0.130 0.037
1 Carpenter
1 Gas Welding Machine

035 304-0100 Formboard,including sub-purlins non-asbestos,fiberglass, 25 mm thick " " 28.00 8.00 205.000 0.137 0.039

035 306 WOOD FIBER:

035 306-0010 Lightweight cement wood fiber, T&G planks, 25 mm thick SQM 2 Carpenters 16.00 0.00 100.000 0.160 0.000

035 306-0011 Lightweight cement wood fiber, T&G planks, 65 mm thick " " 16.00 0.00 90.000 0.178 0.000

Page 70