ASSEMBLY INSTRUCTIONS

STREAMLINE 3000
QUEEN
ONE PIECE DOOR WALL BEDS

Tools Required For Assembly

No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer

Electric Drill (Hammer Drill for Masonry) 6.5mm Masonry Drill Bit Pliers

Spirit Level Adjustable Spanners 24mm Socket Set

12.12.19
 Cabinet Components

1.

7. 2.

13.

8.
9. 10. 6.
11.

12. 3.

14.

4. 5.

Panels (Queen) Panel # Size (mm)

1 x Top 1 1560 x 471 x 16

1 x Top Back Rail 2 1560 x 250 x 16
1 x Back Rail 3 1560 x 570 x 16
1 x Front Skirting 4 1560 x 100 x 16
1 x Bottom 5 1560 x 464 x 16
1 x Right Hand End 6 2230 x 505 x 16
1 x Left Hand End 7 2230 x 505 x 16
1 x Door 8 2126 x 1556 x 16*
1 x Left Hand Frame Rail 9 2032 x 160 x 16
1 x Right Hand Frame Rail 10 2032 x 160 x 16
2 x Mid Frame Rail 11, 12 2000 x 160 x 16
1 x Top Frame Rail 13 1468 x 160 x 16
1 x Bottom Frame Rail 14 1468 x 160 x 16
2x 3mm Packers 15, 16 2000 x 30 x 16
1 x Pillow Catch Note shown in image above, refer to Diagram 1 1500 x 370 x 16
1 x Head Board Note shown in image above, refer to Diagram 1 1500 x 295 x 16

Cabinet Construction
This is the recommended cabinet construction method to ensure the mechanism operates correctly. Variations of construction
should be checked with Pardo. 16 or 18mm thick particleboard doors are recommended.

Mattress size 1500 x 2050 x 250D MAXIMUM depth

Door + Mattress 60 kgs MAXIMUM weight

*If door is produced in 2 x pieces additional structural support is required. Refer to detail H.

Pillowcatch
Cupboard Board is to lean back
against the back rail

Piano hinge Both edges to 370mm

Pillowcatch
Piano hinge Both
be at 23 to
cutedges
be cut at 17
degrees
Piano Hinge
degrees 23 deg. angle to both edges
250mm (refer to detail above)
270mm
Head Board with 4 x holes
Detail
Detail
Bolt thru back of pillowcatch so
that the nut is on the inside of the
DIAGRAM 11
DIAGRAM
frame

1.
 Mechanism Components

2 x Cabinet Angle Brackets Bolts / Nuts / Screws - Various

2 x Bed Straps 30 Slats

2 x Mounting Brackets 60 Slat Cup Holders

1 x Manual Foot
2 x Counter Balance Mechanism

Cabinet Hardware

64 x Cams 64 x Cam Bolts 10 x Green Wall Plugs

1 x Piano Hinge 15 x Large Trim Caps 2 x Handles

4 x Nut, Bolt and

Double Washer setup

2.
 Step1 - Fixing Cabinet To Wall

* Lay cabinet face down with bottom facing the wall.

* To ensure the cabinet is flush against the wall when upright, it may be necessary to cut a larger recess
into bottom of left and right hand end of cabinet.

* Lift cabinet at top, pushing towards wall, being careful to have sufficient ceiling clearance.

* Place cabinet into position against the wall and, using a spirit level against either the right or left hand end and the top,
find the correct vertical and horizontal position. Mark this position on the wall with a pencil.

Refer to detail A

Wall plugs

Fastening with
angle brackets

DETAIL A

Wall
End Panel

Skirting
Board

Base
Panel
Cut skirting recess
Refer to detail B before pushing cabinet
against the wall
Front Panel
DETAIL B

FASTENING OPTIONS 1 FASTENING OPTIONS 2

(for gyprock, fibro or timber walls) (for brick/masonry walls)

* Locate wall studs and mark clearly with pencil. * Ensure cabinet is in correct vertical position.

* With a pencil or nail, mark the wall through the

* Sit angle brackets in cabinet top, flush with top and
back edge and against the wall studs. Ensure that the predrilled holes in the top back rail and the
twin hole side of bracket is against the wall. bottom back rail.

* Fix angle brackets through wall into studs using * Move cabinet aside. Using a 6.5mm masonry bit,
65mm screws. drill 60mm deep holes into wall and insert wall plugs
supplied.

* Ensure cabinet is in correct vertical position. * Move cabinet back into place against wall.
Fix bottom of brackets into cabinet top using
16mm screws. * Fix top back rail to wall through predrilled holes
using 65mm screws. put on cover caps.

* Fix bottom back rail to wall. Countersink screws * Fix bottom back rail to wall. Countersink screws
to avoid pillow catch scraping on them. to avoid pillow catch scraping on them.

PLEASE NOTE
As there is a lot of tension in the Wallbed when in the open position, it is
very important that the cabinet is securely fixed to the wall.

3.
 Step2 - Wall Bed mechanism Assembly / Installation

* Bolt bed frame mounting brackets to left and right ends through predrilled holes using
sleeves and bolts provided. (DETAIL C)
DETAIL C
* Bolt left and right hand counter balance mechanisms to door bed frame.
(Ensuring counter balances are to inside of door bed frame).

* Prior to fitting bed frame into cabinet, be sure leveling screws are protruding
2-3mm out of - the bottom of the block (for later adjustment). Sit pivot block into
mounting brackets (Diagram 2).
When complete, leave bed frame vertical in cabinet.

* Fit manual foot to top of door bed frame (Diagram 3).

Note: Door is now ready to lift upwards.

As there is no tension on the mechanism, the doors are very heavy.

* With one person each side of the bed, lift door up to within 30º of closing (Diagram 4).

DIAGRAM 2 DIAGRAM 3
SITTING PIVOT BLOCK INTO MOUNTING BRACKETS

Mounting Bracket

Levelling Screw

Leave Levelling Screw

5mm clearance for later
adjustment

Manual Foot

Pivot Block Counter Balance

Mechanism

* With a large 24mm socket turn tension handle clockwise on counter balance mechanisms to adjust tension.
(Approximately 30 quarter turns would adjust tension sufficiently for a medium weight mattress.)
* Test by lowering the cabinet door to floor and up again. The correct tension is achieved when the bed frame and doors
lift slightly off the floor without the weight of a mattress.

* If Headboard and pillowcatch are being used, hinge them together using piano hinge.

* Bolt Headboard to head of bed door frame.

* Attach handles to door (handles not supplied).

* Attach bed straps to sides of bed frame by sliding ends through sewn loops over frame edge, approximately 300mm from
head and foot of bed frame, and tighten until secure.

* Slide mattress onto bed frame and secure with bed straps.
* Close doors and again ensure that they align with cabinet. Final adjustment may be neccessary
and can be done by turning leveling screws in mounting block whilst the bed is open at 30º. (Diagram 5)

WARNING
When operating the wallbed mechanism the bed frame must be carefully lowered
all the way to the floor and not left to drop freely. If the bed frame is lowered
without the weight of a mattress it may spring back causing injury.

4.
DIAGRAM 4 ADJUST TENSION COUNTER BALANCE MECHANISMS

Lift doors up to within 30 degrees of closing

Turn tension handles clockwise to increase tension

30

+
_

DIAGRAM 5
ADJUSTING LEVELLING SCREWS

Final adjustment of doors may be made by

adjusting levelling screws in mounting block
whilst bed is open at 30 degrees

5.
 Carcass Construction - Queen Manual Foot Wall Bed Mechanism
12.5mm dia. x 8mm
deep counterbore
to external face of 7mm
2mm dia.thru holes.
73mm 7mm dia. thru hole
Refer to detail H

Top Rail
30 slats & caps
provided to be
fixed to top of 35mm dia. x 11mm
this face
Door As Dotted DETAIL D
Skirting As Dotted

NOTE: CABINET CONSTRUCTION

THIS IS THE RECOMMENDED
CABINET CONSTRUCTION METHOD
TO ENSURE THE MECHANISM
OPERATES CORRECTLY.
VARIATIONS OF CONSTRUCTION
SHOULD BE CHECKED WITH
PARDO PRIOR TO CHANGES.

2126
Wall

2230mm

Door

QUEEN BED
Middle Rail

471mm MIN.

Door
Refer to detail G
160 16
Refer to detail D
Ø 35 35

35 diam. pivot hole

96

Refer to detail E
through board
127

Allow for existing

260

56
2

skirting if any
100

Floor Line

Carcass Side Elevation n.t.s Door Side Elevation n.t.s

4

Wall

1560
For 250mm thick mattress

30 1500 30
2

45 degree
Min 471mm

angle
chamfer
16 711 16 14 16 711 16
100

3 708 708 3

DETAIL E
2
Refer to detail F in Door
installation instructions Plan n.t.s.

6.
 Carcass Construction - Queen Manual Foot Wall Bed Mechanism

PLASTIC CUP (SLAT HOLDER)

35

1468

1500
160
CONTINUOUS ANGLE
ALLROUND TO FIX
BASE TO DOOR

DOOR

28 16 3
1556

DETAIL F
N.T.S

SCREW POINTS FOR

FOOT / LEG
608 1345
SIDE
64 7

79
48

60

160
64

32

32 62
48

2126

Add 70MM x 45MM timber DOOR Add full width 70MM x 45MM
structural support between timber structural support if door is
mechanism if door is 7mm DIA. THROUGH HOLES produced in 2 x pieces.
produced in 2 x pieces.
DETAILS G & H
N.T.S Add full width 70MM x 45MM
timber structural support at centre
if door is produced in 2 x pieces.

7.