D-NWG-FN-23

Exam Name: Dell Networking Foundations 2023

Full version: 281 Q&As

Full version of D-NWG-FN-23 Dumps

Share some D-NWG-FN-23 exam dumps

below.

1. Which message is sent by a router when TTL expires?

A. Echo request
B. Time exceeded
C. Destination unreachable
D. Echo reply
Answer: B

2. Refer to the output shown:

console (config-if-Tel/0/1) #switchport general allowed vlan add 2-6
console (config-if-Tel/0/1) #show interfaces switchport tengigabitethernet 1/0/1 Port: Tel/0/1
VLAN Membership Mode: General Mode Access Mode VLAN: 1 (default)
General Mode PVID: 1 (default)
General Mode Ingress Filtering: Enabled General Mode Acceptable Frame Type: Admit
All General Mode Dynamically Added VLANs: General Mode Untagged VLANs: 1-6
General Mode Tagged VLANs: General Mode Forbidden VLANs:
Trunking Mode Native VLAN: 1 (default) Trunking Mode Native VLAN Tagging:
Disabled Trunking Mode VLANs Enabled: All
Private VLAN Host Association: none Private VLAN Mapping:
Private VLAN Operational Bindings: Default Priority: 0
Protected: Disabled
Te1/01 interface must allow VLANs 2-6 and follow the 802.1Q standard.
Which change should be made to meet the requirements?
A. Add “tagged” command before VLAN ID
B. Add “tagged” at the end of the command
C. Add “trunk” at the end of the command
D. Add “802.1Q” at the end of the command
Answer: B

3. What accurately describes OSPF?

A. Interior gateway link-state protocol
B. Exterior gateway distance-vector protocol
C. Interior gateway distance-vector protocol
D. Interior gateway path-vector protocol
Answer: A

4. A client needs to allow Telnet traffic from the 192.168.1.0/25 network. The client needs to
configure the “permit” statement in the ACL.
Which command will accomplish this goal?
A. console(config-ip-acl)#permit tcp 192.168.1.0 255.255.255.128 any eq 23
B. console(config-ip-acl)#permit tcp 192.168.1.0 255.255.255.0 any eq 23
C. console(config-ip-acl)#permit tcp 192.168.1.0.0.0.0.255 any eq 23
D. console(config-ip-acl)#permit tcp 192.168.1.0.0.0.0.127 any eq 23
Answer: D

5. What benefit does VRRP version 3 provide over VRRP version 2 in OS10?
A. Provides preemption capability.
B. Provides MD5 authentication.
C. Allows subsecond timers.
D. Allows multiple masters in the topology.
Answer: C

6. What is the purpose of the control plane in a router?

A. Determine where to forward incoming IP packets
B. Maintain the routing table
C. Carry user traffic for the router
D. Forward routed protocols for the router
Answer: B

7. What are the mandatory TLV fields in a LLDP PDU frame?

A. IP Address
Default Gateway
Port ID
B. Port Description
System Name
System Description
C. Chassis ID
Port ID
Time-to-Live
D. System Capabilities
Management Address
Time-to-Live
Answer: C

8. On which OSI layers do standard ACL filters operate?

A. 2 and 3
B. 2 and 7
C. 3 and 4
D. 4 and 7
Answer: C

9. There is a spanning tree mismatch at the global level. PVST+ is configured on a VLT peer. All
VLT port channels go down on both VLT peers. A syslog error message is generated.
What is the correct action to resolve the issue?
A. Verify the VLT LAG ID is configured correctly on both VLT peers.
B. Enable RSTP on both VLT peers.
C. Use the show VLT detail and show VLT brief commands to view the VLT port channel status
information.
D. Perform a mismatch check after the VLT peer is established.
Answer: D
Explanation:
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-fx2/dell fn ioa config_9.8
.0.0_pub-v1/troubleshooting-vlt?guid=guid-9978ac1f-1305-4590-9c64-bb35bd6e012a&lang=en-
us

10. What is required to enable ECMP in BGP?

A. OSPF must install equal cost paths in the routing table for BGP to use ECMP.
B. Maximum-paths and multipath-relax commands.
C. Sub-interfaces must be configured on the physical interface running BGP.
D. ECMP is not possible in BGP.
Answer: B

11. Which protocols use a central server to authenticate users?

A. ARP and IMAP
B. RADIUS and ARP
C. TACACS+ and IMAP
D. TACACS+ and RADIUS
Answer: D

12. What is the default route preference value for a Border Gateway Protocol (BGP) internal
route?
A. 40
B. 110
C. 200
D. 253
Answer: C

13. What is an advantage of UFD?

A. Reduces connectivity loss.
B. Detects the loss of downstream connectivity.
C. Reduces network complexity.
D. Prevents the loss of upstream connectivity.
Answer: D

14. Which Dell EMC Networking operating system does an N-Series switch use?
A. OS 3
B. OS 6
C. OS 9
D. OS 10
Answer: B

15. What is the correct sequence of steps that occur in the communications between the client
and server to obtain an IP address from a DHCP server?

Answer:
16. A technician must deploy powering source equipment at a customer site.
Which equipment should the technician deploy?
A. Ethernet switches
B. VoIP phones
C. Network surveillance cameras
D. Thin client
Answer: A

17. A dell Networking N-Series has configured a port-channel with LACP using the interfaces
Tel/0/1 and Tel/0/2.
How is the egress traffic distributed among the interfaces?
A. Load balanced using a hash function
B. Load balanced per packet using Round Robin
C. Traffic overflow will be sent to the second interface
D. Interfaces will be used in active/passive
Answer: A

18. Refer to the exhibit.

Which configuration will allow S1 to ping S2’s Lo0 address?
A. S1(config-router)# ip route 144.254.32.1 192.168.32.2/32
B. S1(config-router)# ip route 192.168.32.2 144.254.32.1/32
C. S1(config)# ip route 144.254.32.1/32 192.168.32.2
D. S1(config)# ip route 192.168.32.2 144.254.32.1/32
Answer: C

19. You recently joined a company as a junior-level network administrator. You have been
tasked with designing the IPv4 scheme for five networks that will be used for training
classrooms.
These networks need to support no more than 28 devices each. Due to the existing network
design, the senior-level network administrator has asked you to work on the network
192.168.40.0/24.
If all networks must be made to logically start with the lowest numbered network and end with
the largest numbered network, which subnet mask achieves this design?
A. 255.255.255.128
B. 255.255.255.192
C. 255.255.255.224
D. 255.255.255.240
Answer: C

20. What is the decimal equivalent of the binary number 10101010 in IPv4?
A. 162
B. 170
C. 192
D. 244
Answer: B
21. Which switchport command must be applied to an interface to allow Voice VLAN
configurations?
A. Switchport mode general
B. Switchport voice detect auto
C. Switchport mode trunk
D. Switchport dot1q ethertype 802.1Q
Answer: B

22. In the OS10 CLI what does Ctrl+A do?

A. Deletes all the text before the cursor.
B. Moves the cursor to the start of the command line.
C. Moves the cursor to the end of the command line.
D. Deletes the word before the cursor.
Answer: B

23. Which type of protocol is OSPF and what metric does it use to determine best path?
A. Link-state protocol that uses a concept of cost as metric
B. Hybrid protocol that uses hop count as a metric
C. Path vector protocol that uses the Dijkstra algorithm as a metric
D. Distance Vector protocol that uses bandwidth and delay as metric
Answer: A

24. What type of network in a Data Center flattens the core and aggregation layers into a single
tier?
A. Leaf
B. Leaf-spine
C. Spine
D. TRILL
Answer: B

25. What is the IEEE 802.3 identifier for 100 Mb/s Ethernet over fiber optic cable?
A. 100BASE-F
B. 100BASE-FX
C. 100BASE-T
D. 100BASE-TX
Answer: B

26. Which formula is used for calculating OSPF interface costs?

A. Reference bandwidth C interface bandwidth
B. Reference bandwidth / interface bandwidth
C. Reference bandwidth + interface bandwidth
D. Interface bandwidth / reference bandwidth
Answer: B

27. An N-Series switch is configured to route between VLANs 1 and 2. The DHCP server is on
VLAN1.
How should the technician make sure the DHCP server can allocate IP addresses to clients on
VLAN 2?
A. Configure DHCP Snooping feature on VLAN 2
B. Configure VLAN 2 with an ip-helper
C. Configure static IP addresses on VLAN 2
D. Configure DHCP option 150 on the server
Answer: B

28. A technician implements a new copper connection to Gi2/0/20.

Which command should be used to check the cable length?
A. test tdr copper-length gigabitethernet 2/0/20
B. test copper-length tdr gigabitethernet 2/0/20
C. test tdr copper-port gigabitethernet 2/0/20
D. test copper-port tdr gigabitethernet 2/0/20
Answer: D

29. On Switch A, a static route has been redistributed into OSPF.

Which type of OSPF router will this process make Switch A?
A. Autonomous System Boundary Router (ASBR)
B. Designated router (DR)
C. Area Border Router (ABR)
D. Backbone Router (BR)
Answer: A

30. Which of the following is an IPv4 address?

A. 224.0.0.3/8
B. 172.16.225.0/23
C. 10.0.0.255/16
D. 192.168.0.3/30
Answer: C

31. What is the function of the authentication service?

A. Validates the user identity
B. Determines switch management commands
C. Validates switch order
D. Determines which services the user is enabled to access
Answer: A

32. Which IPv6 address type is similar to IPv4 APIPA?

A. Multicast
B. IPv6 link-local
C. Global unicast
D. Unique Local
Answer: B

33. When the show ip bgp neighbors command is issued, which BGP state reflects a
successfully created adjacency with another BGP peer?
A. ESTABLISHED
B. PEERING
C. ACTIVE
D. CONNECTED
Answer: A

34. Which command defines the possible IP addresses that can be leased to clients using
DHCP?
A. ip address 172.16.32.1 / 24
B. lease 8 0 0
C. network 172.16.32.0/24
D. range 172.16.32.100 172.16.32.200
Answer: D

35. Refer to the output from a Dell N-Series switch:

A technician checks the connectivity to the default gateway from the switch and notices the ping
fails.
At which layer does the problem exist?
A. Network
B. Application
C. Transport
D. Session
Answer: A

36. How is a switch different from a hub?

A. A switch operates at a lower, more efficient layer of the OSI model.
B. A switch decreases the number of broadcast storms.
C. A switch tracks MAC addresses of all connected devices.
D. A switch does not include any latency into the frame transfer time.
Answer: C

37. When implementing QoS on a 10Gb connection, 6Gb is required by the customer.
What QoS level best fits the requirement while keeping resource use to a minimum?
A. Differentiated service
B. Guaranteed service
C. FIFO
D. Best-effort service
Answer: B

38. Which LLDP-MED TLV communicates DSCP values?

A. Network policy
B. Port description
C. System description
D. Local identification
Answer: A

39. A technician needs to configure a static LAG between two N-Series switches. Each LAG
must consist of interfaces GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2.
Which commands should the technician use to create the LAG on each switch?
A. console#configure
console(config)#interface range gigabitethernet 1/0/1-2
console(config-if)#channel group 1 mode on
B. console#configure
console(config)#interface range gigabitethernet 1/0/1-2
console(config-if)#channel group 1 active
C. console#configure
console(config)#interface range gigabitethernet 1/0/1-2
console(config-if)#port-channel 1 mode on
D. console#configure
console(config)#interface range gigabitethernet 1/0/1-2
console(config-if)#channel group 1 mode on
Answer: D

40. What are the required commands to configure a native VLAN of 10 and a tagged VLAN of
20 on an OS6 switch?
A. # interface ethernet 1/6
# switchport trunk encapsulation dot1
# switchport trunk native vlan 10
# switchport trunk allowed vlan 20
# switchport mode trunk
B. # interface gigabitethernet 1/0/6
# switchport mode trunk
# switchport mode allow vlan 20
# switchport mode trunk native vlan 10
C. # interface ethernet 1/1/6
# switchport mode trunk
# switchport trunk allowed vlan 20
# switchport access vlan 10
D. # interface gigabitethernet 1/0/7
# switchport mode trunk
# switchport mode allow vlan 20
# switchport mode trunk native vlan 10
Answer: B

41. Which subnet mask provides only two valid IP addresses that can be assigned to hosts?
A. 255.255.255.248
B. 255.255.255.254
C. 255.255.255.252
D. 255.255.255.256
Answer: C

42. Using the MAC 8c-ec-4b-5b-61-9d, what is a valid EUI-64 link local address?
A. 2001::a9:8eec:4bff:fc5b:619d
B. fe80::a9:8cec:4bff:fe5b:619d
C. ff80:a9:8eec:4bff:fe5b:619d
D. fe80::a9:8eec:4bff:fe5b:619d
Answer: B

43. Which Layer 2 technology is used to segment a switched network?

A. Trunking
B. ISL
C. LAN
D. VLAN
Answer: D
 More Hot Exams are available.

350-401 ENCOR Exam Dumps

350-801 CLCOR Exam Dumps

200-301 CCNA Exam Dumps

Powered by TCPDF (www.tcpdf.org)