Fire Alarm Pre-Commissioning Guide
Uploaded by
Binu SulochananFire Alarm Pre-Commissioning Guide
Uploaded by
Binu SulochananTYPE OF DOCUMENT: PRE-COMMISSIONING PROCEDURE
DOCUMENT CODE: FFE/JGC/FA/E-PCP-01
DOCUMENT TITLE:
PRE-COMMISSIONING PROCEDURE OF FIRE ALARM
SYSTEM
VALIDITY:
DATE OF ISSUE: 10-JULY-2013 REVISION : 01 Page 1 of 5
ACTIVE
CONTROLLED DOCUMENT
COPY
NUMBER
CONTROLLED
UNCONTROLLED
FOR INFORMATION ONLY
ISSUED BY: APPROVED BY:
TECHNICAL OFFICE PROJECT MANAGER
DOCUMENT CODE: PRE-COMMISSIONING PROCEDURE Page 2 of 5
FFE/JGC/FA/E-PCP-01 OF FIRE ALARM SYSTEM
TABLE OF CONTENTS
Page No.
1.0 SCOPE OF WORKS 3
1.1 General Description 3
1.2 Tools and Equipment 3
1.3 Ready for pre-commissioning 3
1.4 Pre-Commissioning Activities 3
2.0 APPLICABLE DOCUMENTS 4
3.0 RESPONSIBILITIES 4
4.0 EXECUTION OF PRE-COMMISSIONING ACTIVITIES 4
5.0. PROCEDURES 5
1.0 SCOPE OF WORK
DOCUMENT CODE: PRE-COMMISSIONING PROCEDURE Page 3 of 5
FFE/JGC/FA/E-PCP-01 OF FIRE ALARM SYSTEM
1.1General Description
This procedure describes the sequence of pre-commissioning
activities, equipments, tools and resources required for FIRE ALARM
SYSTEM at KJO SWGH where in accordance with relevant sections of
KJO Project specifications, Fire Alarm and Detection Systems and
NFPA 3.Pre-commissioning activity will be started after completion
of equipment installation & physical inspection.
1.2 Tools and Equipment
The following Tool and equipment will be used as and when
necessary to carry out pre-commissioning activities.
Item
Tools and Equipment Purpose
No.
1 Multi meter Digital To check voltage and continuity
2 Smoke Tester Detector Test device
3 Heat Tester Detector Test device
To check functionality of the
4 Device Testing Kit
detectors and other devices
1.3 Ready for Pre-Commissioning
The works are ready for pre-commissioning when the company has
issued a certificate for installation completion and notification in writing
that the works is ready for pre-commissioning.
1.4 Pre-Commissioning Activities
Pre-commissioning activities are to be performed after completion
of a piece of equipment or system to make it safe and ready for -
commissioning .This includes, but not limited to
. Performance of all remaining works other than commissioning &
functional test.
. The completion of all inspections.
. The items for which a defect notice are issued to be rectified and
and all defect notices shall have been closed out.
.Checking & Site Modifications
. Make available necessary tools required to carry out activities.
DOCUMENT CODE: PRE-COMMISSIONING PROCEDURE Page 4 of 5
FFE/JGC/FA/E-PCP-01 OF FIRE ALARM SYSTEM
. The availability of trained engineers
. Notify 48 hrs in advance the JGC Engineer prior to commencement
of pre-commissioning activities
2.0 APPLICABLE DOCUMENTS
2.1 Saudi ARAMCO pre-commissioning forms
2.2 NFPA 3
2.3 Manufacturer’s Standard & Manuals
3.0 RESPONSIBILITIES
S/N POSITION/DESIGNATION QTY RESPONSIBLITY
In-charge for all pre-
1 Commissioning Engineer 1 commissioning related
activities of FAS.
To support engineer to carry
2 Supervisor-Electrical 1
out pre-com. activities
Responsible for implementing
3 Technician-Electrical 4
the activities on site
4.0 EXECUTION OF PRE-COMMISSIONING ACTIVITIES
Contractor shall complete all pre-commissioning activities in accordance
with guidelines given in Saudi ARAMCO Standards/Pre-commissioning
forms. Contractor shall write necessary procedures and obtain approval
from Company prior to commencing work and shall carry out the work
in accordance with approved procedures
5.0 PROCEDURES
Check the completion documents along with all design
documents to As-built.
Check detector layout, alarm bells and others accessories were
installed as per approved drawings.
Check the continuity for all the loop lines, conductor to conductor
resistance.
Make sure electric head of FM 200 are not connected to cylinders.
DOCUMENT CODE: PRE-COMMISSIONING PROCEDURE Page 5 of 5
FFE/JGC/FA/E-PCP-01 OF FIRE ALARM SYSTEM
The installed equipments will be inspected and the integrity of the
installation verified.
Mechanical test will comprise of a physical inspection of
installation and termination of each cables and equipment.
Each field device must be individually tested to ensure that it
transmits the correct signal to FACP through loops.
Connect the loops to the panel and power the panel AC & DC.
END OF SECTION
