NSX-SZ80 LH

NSX-SZ83 LH

NSX-AJ80 U

NSX-SZ80E HA

SERVICE MANUAL
COMPACT DISC STEREO BASIC TAPE MECHANISM : 2ZM-3MK2 PR7NM
CASSETTE RECEIVER BASIC CD MECHANISM : AZG-1 ZD3RNDM

CD MAIN SATELLITE REMOTE

SYSTEM SPEAKER SPEAKER CONTROLLER
CASSEIVER
NSX–SZ80 (LH) CX–NSZ80 SX–WNSZ80
NSX–SZ83 (LH) CX–NSZ83 SX–WNH83
SX–S80 RC–ZAS01
NSX–AJ80 (U) CX–NAJ80 SX–WNAJ85
NSX–SZ80E (HA) CX–NSZ80E SX–WNSZ80

• If requiring information about the CD mechanism, see Service Manual of

AZG-1 ZD3RNDM, (S/M Code No. 09-001-335-3N8).

S/M Code No. 09-003-424-4R1

 SPECIFICATIONS

<FM tuner section> <Compact disc player section>

Tuning range 87.5 MHz to 108 MHz Laser Semiconductor laser (λ =780 nm)
Usable sensitivity (IHF) 13.2 dBf D-A converter 1 bit dual
Antenna terminals 75 ohms (unbalanced) Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<AM tuner section> Wow and flutter Unmeasurable
Tuning range 530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step) <General>
Usable sensitivity 350 µV/m Power requirements U: 120 V AC, 60 Hz
Antenna Loop antenna LH, HA: 120 V/220-230 V/240 V AC
(switchable), 50/60 Hz
<Amplifier section> Power consumption U: 165 W
Mid-high frequency amplifier LH, HA: 245 W
Power output LH, HA: Power consumption in If the power-economizing mode is
Rated 35 W + 35 W (6 ohms, standby mode ECO OFF:
T.H.D. 1 %, 1 kHz) LH, HA: 29.5 W
Reference: 45 W + 45 W (6 ohms, U: 27.5 W
T.H.D. 10 %, 1 kHz) If the power-economizing mode is
U: ECO ON or ECO AUTO: 0.9 W
30 W + 30 W (200 Hz - 20 kHz, Dimensions of main unit 260 x 329 x 389.6 mm
T.H.D. less than 1 %, 8 ohms) (W x H x D) (10 1/4 X 13 X 15 3/8 in.)
Total harmonic distortion 0.1 % (25 W, 1 kHz, 8 ohms, Weight of main unit 11.8 kg (26 lbs.)
DIN AUDIO )
Low frequency amplifier <Speaker system SX–WNH83 / SX–WNSZ80 / SX–WNAJ85>
Power output LH, HA: Speaker system 3 way, built-in subwoofer (magnetic
Rated 105 W + 105 W (6 ohms, shielded type)
T.H.D. 1 %, 120 Hz) Speaker units Subwoofer:
Reference: 135 W + 135 W (6 ohms, 200 mm (7 7/8 in.) cone type
T.H.D. 10 %, 120 Hz) Full range:
U: 120 mm (4 3/4 in.) cone type
90 W + 90 W (50 Hz - 200 Hz, Super tweeter:
T.H.D. less than 1 %, 6 ohms) 20 mm (13/16 in.) ceramic type
Total harmonic distortion 0.1 % (75 W, 120 Hz, 6 ohms, Impedance 6 ohms/8 ohms
DIN AUDIO) Output sound pressure level 87 dB/W/m
Satellite amplifier<U only> Dimensions (W x H x D) SX-WNH83 / WNAJ85:
Power output 5 W + 5 W (1 kHz, T.H.D. less than 240 x 324 x 285 mm
1 %, 8 ohms) (9 1/2 X 12 7/8 X 11 1/4 in.)
Total harmonic distortion 0.1 % (3 W, 1 kHz, 8 ohms, SX-WNSZ80: 240 x 384 x 310 mm
DIN AUDIO ) Weight 5.8 kg (12 lbs. 13 oz.)
Inputs VIDEO/AUX: 316 mV (adjustable)
MD: 316 mV (adjustable) <Satellite speaker SX–S80>
MIC: 1.0 mV (10 k ohms) Speaker system Full range (magnetic shielded type)
Outputs SPEAKERS HIGH FREQ: Speakers units 80 mm cone type
accept speakers of 8 ohms or more Impedance 8 ohms
SPEAKERS LOW FREQ: Output sound pressure level 87 dB/W/m
accept speakers of 6 ohms or more Dimensions (W x H x D) 100 x 327 x 105 mm
SATELLITE SPEAKERS: (4 X 12 7/8 X 4 1/4 in.)(with pedestal)
accept speakers of 8 ohms or more 100 x 190 x 81 mm
SURROUND SPEAKERS: (4 X 7 1/2 X 3 1/4 in.)(without pedestal)
accept speakers of 8 ohms to 16 ohms Weight 0.6 kg (1 lbs. 5 oz.)
LINE OUT: 210 mV
PHONES (stereo jack): accepts
headphones of 32 ohms or more

<Cassette deck section>

Track format 4 tracks, 2 channels stereo
Frequency response CrO2 tape: 50 Hz – 16000 Hz
NORMAL tape: 50 Hz – 15000 Hz • Design and specifications are subject to change without notice.
Recording system AC bias
Heads Deck 1: Playback head x 1
Deck 2: Recording/Playback head • The word "BBE"and the "BBE symbol" are trademarks of BBE
x 1, erase head x 1 Sound, Inc.
Under license from BBE Sound,Inc.

–2–
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully CAUTION

the instructions below when servicing. Use of controls or adjustments or performance of proce-
dures other than those specified herin may result in
WARNING!! hazardous radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS ATTENTION
NECESSARY TO CONFIRM LASER BEAM EMISSION. L’utillisation de commandes, réglages ou procédures
BE SURE TO OBSERVE FROM A DISTANCE OF MORE autres que ceux spécifiés peut entraîner une dangereuse
THAN 30cm FROM THE SURFACE OF THE OBJEC- exposition aux radiations.
TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
ADVARSEL
s Caution: Invisible laser radiation when Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
open and interlocks defeated avoid ude af funktion. Undgå udsættelse for stråling.
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning, This Compact Disc player is classified as a CLASS 1
når sikkerhedsafbrydere er ude af funktion.
LASER product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle. CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
VARNING! LUOKAN 1 LASER LAITE
Om apparaten används på annat sätt än vad som KLASS 1 LASER APPARAT
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

Precaution to replace Optical block

PICK-UP Assy P.C.B
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.

1) After the connection, remove solder shown in

right figure.

Solder

–3–
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2

Select a discharging resistor referring to the following table. Fig-1

Charging voltage (V) Discharging
Rated power (W) Parts number
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.

–4–
 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
R
TE

FRONT C.B
PU
M
CO
RO

18 % VSS
IC

15
M

C113 MICRO-
COMPUTER
* VDD
C113
FRONT C.B
Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

–5–
ELECTRICAL MAIN PARTS LIST

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
IC C22 87-016-658-000 CAP,E 4700-35 M SMG
C25 87-010-382-080 CAP, ELECT 22-25V
8A-NF6-610-030 C-IC,LC87654V-5P35 C26 87-010-382-080 CAP, ELECT 22-25V<EXCEPT 80U>
87-A21-418-010 IC,STK490-340 C26 87-010-383-080 CAP, ELECT 33-25V<80U>
87-A21-018-040 C-IC,M65849BFP631D C27 87-010-382-080 CAP, ELECT 22-25V
87-A21-396-010 IC,STK490-040<80U>
87-A21-397-010 IC,STK490-070<EXCEPT 80U> C28 87-010-382-080 CAP, ELECT 22-25V<EXCEPT 80U>
C28 87-010-383-080 CAP, ELECT 33-25V<80U>
87-A20-914-010 IC,SPS-442-1-F C31 87-010-263-080 CAP, ELECT 100-10V
87-A20-783-040 C-IC,BA7762AFS C32 87-010-197-080 CAP, CHIP 0.01 DM
87-A21-577-040 C-IC,M61506FP C33 87-010-263-080 CAP, ELECT 100-10V<80U>
87-A21-021-040 C-IC,BU2099FV
87-070-289-040 IC,BU 2092F C34 87-010-247-080 CAP, ELECT 100-50V
C35 87-010-260-080 CAP, ELECT 47-25V
87-A21-452-030 C-IC,BD3876KS2 C36 87-010-381-080 CAP, ELECT 330-16V
87-A21-051-040 C-IC,BU9990-03FS<EXCEPT 80U> C38 87-010-384-080 CAP, ELECT 100-25V
87-A21-415-010 IC,LA1843 C39 87-010-384-080 CAP, ELECT 100-25V
87-070-127-110 IC,LC72131 D
87-020-454-010 IC,DN 6851 C40 87-010-197-080 CAP, CHIP 0.01 DM
C60 87-010-403-080 CAP, ELECT 3.3-50V
C80 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 80U>
TRANSISTOR C81 87-010-374-080 CAP, ELECT 47-10V<EXCEPT 80U>
C82 87-010-260-080 CAP, ELECT 47-25V<EXCEPT 80U>
87-026-245-080 TR,DTC114ES
87-A30-198-080 TR,KTC3199GR C104 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-075-080 C-TR,2SA1235F C105 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-318-080 TR,CSA952K C111 87-010-545-080 CAP, ELECT 0.22-50V
89-213-702-010 TR,2SB1370 (1.8W) C112 87-010-545-080 CAP, ELECT 0.22-50V
C113 87-010-545-080 CAP, ELECT 0.22-50V
87-A30-076-080 C-TR,2SC3052F
87-026-610-080 TR,KTC3198GR C114 87-010-545-080 CAP, ELECT 0.22-50V
87-026-609-080 TR,KTA1266GR C115 87-010-546-080 CAP, ELECT 0.33-50V
87-A30-087-080 C-FET,2SK2158 C116 87-010-546-080 CAP, ELECT 0.33-50V
87-A30-107-070 C-TR,CMBT5401 C121 87-010-546-080 CAP, ELECT 0.33-50V
C122 87-010-546-080 CAP, ELECT 0.33-50V
87-A30-468-080 C-TR,KRC102S-RTK
87-A30-074-080 C-TR,RT1P141C C171 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-269-040 C-FET,2SJ461-T1 C172 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-106-040 C-TR,CMBT5551 C173 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-086-040 C-TR,CSD1306E C174 87-012-368-080 C-CAP,S 0.1-50 F
C301 87-010-318-080 C-CAP,S 47P-50 J CH
87-A30-190-080 TR,CC5551
89-420-613-010 TR,2SD2061F C302 87-010-318-080 C-CAP,S 47P-50 J CH
89-213-703-010 TR,2SB1370F C303 87-012-157-080 C-CAP,S 330P-50 CH
87-A30-063-080 C-TR,KRA104S C304 87-012-157-080 C-CAP,S 330P-50 CH
87-A30-086-070 C-TR,CSD1306E C305 87-012-157-080 C-CAP,S 330P-50 CH
C306 87-012-157-080 C-CAP,S 330P-50 CH
87-A30-329-080 TR,CD1585BC
89-327-143-080 TR,2SC2714 (0.1W) C307 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-489-080 C-TR,KRA107S C309 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-234-080 TR,CSC4115BC C310 87-010-196-080 CHIP CAPACITOR,0.1-25
87-026-463-080 TR,2SA933S C311 87-010-198-080 CAP, CHIP 0.022
C312 87-010-198-080 CAP, CHIP 0.022

DIODE C313 87-010-179-080 CAP,CHIP S B1200P

C314 87-010-179-080 CAP,CHIP S B1200P
87-A40-673-090 DIODE,D10XB20 C315 87-010-179-080 CAP,CHIP S B1200P
87-A40-547-090 DIODE,D5SBA20 C316 87-010-179-080 CAP,CHIP S B1200P
87-020-465-080 DIODE,1SS133 C321 87-012-142-080 CAP, S 0.33-16
87-A40-553-080 DIODE,1N4003 LES
87-A40-784-080 ZENER,UZ39BSB C322 87-012-142-080 CAP, S 0.33-16
C324 87-010-260-080 CAP, ELECT 47-25V
87-A40-764-080 ZENER,UZ10BSC C325 87-010-370-080 CAP,E 330-6.3 SME
87-A40-313-080 C-DIODE,MC 2840 C327 87-010-404-080 CAP, ELECT 4.7-50V
87-A40-270-080 C-DIODE,MC2838 C328 87-010-404-080 CAP, ELECT 4.7-50V
87-A40-269-080 C-DIODE,MC2836
87-A40-768-080 ZENER,UZ16BSA C332 87-010-196-080 CHIP CAPACITOR,0.1-25
C335 87-010-401-080 CAP, ELECT 1-50V
87-A40-752-080 ZENER,UZ6.2BSC C336 87-010-401-080 CAP, ELECT 1-50V
87-A40-748-080 ZENER,UZ5.6BSA C337 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A40-802-080 ZENER,UZ5.1BSC C339 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A40-747-080 ZENER,UZ5.1BSB
87-A40-745-080 ZENER,UZ4.7BSA C340 87-010-196-080 CHIP CAPACITOR,0.1-25
C351 87-012-140-080 CAP 470P
87-A40-749-080 ZENER,UZ5.6BSB<EXCEPT 80U> C352 87-012-140-080 CAP 470P
87-017-149-080 ZENER,HZS6A2L C354 87-010-175-080 CAP 560P
C355 87-010-178-080 CHIP CAP 1000P

MAIN C.B C356 87-010-260-080 CAP, ELECT 47-25V

C357 87-010-197-080 CAP, CHIP 0.01 DM
C3 87-012-368-080 C-CAP,S 0.1-50 F C358 87-010-183-080 C-CAP,S 2700P-50 B
C4 87-012-368-080 C-CAP,S 0.1-50 F C359 87-010-183-080 C-CAP,S 2700P-50 B
C21 87-016-658-000 CAP,E 4700-35 M SMG C360 87-010-183-080 C-CAP,S 2700P-50 B

–6–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C370 87-010-196-080 CHIP CAPACITOR,0.1-25 C641 87-010-401-080 CAP, ELECT 1-50V
C373 87-016-083-080 C-CAP,S 0.15-16 RK C642 87-010-401-080 CAP, ELECT 1-50V
C374 87-016-083-080 C-CAP,S 0.15-16 RK C643 87-010-196-080 CHIP CAPACITOR,0.1-25
C378 87-010-196-080 CHIP CAPACITOR,0.1-25 C644 87-010-401-080 CAP, ELECT 1-50V
C379 87-010-382-080 CAP, ELECT 22-25V C671 87-010-322-080 C-CAP,S 100P-50 CH

C380 87-010-382-080 CAP, ELECT 22-25V C672 87-010-322-080 C-CAP,S 100P-50 CH

C381 87-010-197-080 CAP, CHIP 0.01 DM C673 87-010-197-080 CAP, CHIP 0.01 DM
C382 87-010-312-080 C-CAP,S 15P-50 CH C679 87-010-196-080 CHIP CAPACITOR,0.1-25
C383 87-010-197-080 CAP, CHIP 0.01 DM C680 87-010-197-080 CAP, CHIP 0.01 DM
C384 87-010-402-080 CAP, ELECT 2.2-50V C682 87-010-196-080 CHIP CAPACITOR,0.1-25

C386 87-010-196-080 CHIP CAPACITOR,0.1-25 C771 87-010-263-080 CAP, ELECT 100-10V

C387 87-012-145-080 CAP, CHIP S 270P CH C772 87-010-197-080 CAP, CHIP 0.01 DM
C388 87-012-156-080 C-CAP,S 220P-50 CH C773 87-010-184-080 CHIP CAPACITOR 3300P(K)
C391 87-010-319-080 C-CAP,S 56P-50 CH C774 87-010-184-080 CHIP CAPACITOR 3300P(K)
C392 87-010-319-080 C-CAP,S 56P-50 CH C779 87-A10-679-080 C-CAP,S 3300P-50 JR

C393 87-010-319-080 C-CAP,S 56P-50 CH C780 87-A10-679-080 C-CAP,S 3300P-50 JR

C394 87-010-319-080 C-CAP,S 56P-50 CH C782 87-010-197-080 CAP, CHIP 0.01 DM
C501 87-010-263-080 CAP, ELECT 100-10V C783 87-010-197-080 CAP, CHIP 0.01 DM
C502 87-010-196-080 CHIP CAPACITOR,0.1-25 C784 87-010-197-080 CAP, CHIP 0.01 DM
C503 87-012-393-080 C-CAP,S 0.22-16 R K C785 87-010-197-080 CAP, CHIP 0.01 DM

C504 87-012-393-080 C-CAP,S 0.22-16 R K C786 87-010-197-080 CAP, CHIP 0.01 DM

C505 87-012-141-080 CHIP-CAPACITOR,0.22-16F C788 87-010-149-080 C-CAP,S 5P-50 CH
C506 87-010-184-080 CHIP CAPACITOR 3300P(K) C789 87-A10-592-080 C-CAP,S 0.015-50 J B
C507 87-010-177-080 C-CAP,S 820P-50 SL C790 87-A10-592-080 C-CAP,S 0.015-50 J B
C508 87-016-669-080 C-CAP,S 0.1-25 K B C791 87-010-196-080 CHIP CAPACITOR,0.1-25

C509 87-016-669-080 C-CAP,S 0.1-25 K B C792 87-010-197-080 CAP, CHIP 0.01 DM

C510 87-010-184-080 CHIP CAPACITOR 3300P(K) C793 87-010-404-080 CAP, ELECT 4.7-50V
C511 87-010-177-080 C-CAP,S 820P-50 SL C795 87-010-197-080 CAP, CHIP 0.01 DM
C512 87-012-141-080 CHIP-CAPACITOR,0.22-16F C796 87-010-197-080 CAP, CHIP 0.01 DM
C513 87-010-544-080 CAP, ELECT 0.1-50V C797 87-010-405-080 CAP, ELECT 10-50V

C514 87-010-374-080 CAP, ELECT 47-10V C798 87-010-197-080 CAP, CHIP 0.01 DM
C515 87-010-401-080 CAP, ELECT 1-50V C799 87-010-407-080 CAP, ELECT 33-50V
C516 87-010-401-080 CAP, ELECT 1-50V C800 87-012-369-080 C-CAP,S 0.047-50F
C517 87-010-183-080 C-CAP,S 2700P-50 B C801 87-010-403-080 CAP, ELECT 3.3-50V
C518 87-010-183-080 C-CAP,S 2700P-50 B C802 87-012-369-080 C-CAP,S 0.047-50F

C531 87-010-405-080 CAP, ELECT 10-50V C803 87-010-198-080 CAP, CHIP 0.022
C532 87-010-196-080 CHIP CAPACITOR,0.1-25 C804 87-010-263-080 CAP, ELECT 100-10V
C533 87-010-196-080 CHIP CAPACITOR,0.1-25 C807 87-010-400-080 CAP, ELECT 0.47-50V
C534 87-012-156-080 C-CAP,S 220P-50 CH C808 87-010-401-080 CAP, ELECT 1-50V
C535 87-010-178-080 CHIP CAP 1000P C809 87-010-401-080 CAP, ELECT 1-50V

C536 87-010-196-080 CHIP CAPACITOR,0.1-25 C810 87-010-196-080 CHIP CAPACITOR,0.1-25

C538 87-010-318-080 C-CAP,S 47P-50 CH C811 87-010-403-080 CAP, ELECT 3.3-50V
C541 87-010-178-080 CHIP CAP 1000P C812 87-010-403-080 CAP, ELECT 3.3-50V
C609 87-010-181-080 CAP,CHIP S 1800P C814 87-010-197-080 CAP, CHIP 0.01 DM
C610 87-010-181-080 CAP,CHIP S 1800P C815 87-010-400-080 CAP, ELECT 0.47-50V

C611 87-010-956-080 CHIP-CAP,S 0.068-25B C816 87-010-400-080 CAP, ELECT 0.47-50V

C612 87-016-369-080 C-CAP,S 0.033-25 B K C819 87-010-179-080 CAP,CHIP S B1200P
C613 87-010-197-080 CAP, CHIP 0.01 DM C820 87-010-179-080 CAP,CHIP S B1200P
C614 87-016-669-080 C-CAP,S 0.1-25 K B C821 87-010-405-080 CAP, ELECT 10-50V
C616 87-010-184-080 CHIP CAPACITOR 3300P(K) C823 87-010-177-080 C-CAP,S 820P-50 SL

C617 87-012-369-080 C-CAP,S 0.047-50F C824 87-010-405-080 CAP, ELECT 10-50V

C618 87-010-401-080 CAP, ELECT 1-50V C825 87-010-596-080 CAP, S 0.047-16
C619 87-010-263-080 CAP, ELECT 100-10V C842 87-010-197-080 CAP, CHIP 0.01 DM
C620 87-016-669-080 C-CAP,S 0.1-25 K B C843 87-010-197-080 CAP, CHIP 0.01 DM
C621 87-010-197-080 CAP, CHIP 0.01 DM C844 87-010-197-080 CAP, CHIP 0.01 DM

C623 87-010-401-080 CAP, ELECT 1-50V C845 87-010-197-080 CAP, CHIP 0.01 DM
C624 87-010-401-080 CAP, ELECT 1-50V C846 87-010-197-080 CAP, CHIP 0.01 DM
C626 87-010-596-080 CAP, S 0.047-16 C847 87-010-197-080 CAP, CHIP 0.01 DM
C627 87-010-400-080 CAP, ELECT 0.47-50V C848 87-010-197-080 CAP, CHIP 0.01 DM
C628 87-010-400-080 CAP, ELECT 0.47-50V C849 87-010-197-080 CAP, CHIP 0.01 DM

C629 87-010-596-080 CAP, S 0.047-16 C850 87-010-260-080 CAP, ELECT 47-25V

C630 87-010-383-080 CAP, ELECT 33-25V C851 87-010-197-080 CAP, CHIP 0.01 DM
C631 87-010-185-080 C-CAP,S 3900P-50 B C852 87-010-197-080 CAP, CHIP 0.01 DM
C632 87-010-185-080 C-CAP,S 3900P-50 B C853 87-010-197-080 CAP, CHIP 0.01 DM
C634 87-010-196-080 CHIP CAPACITOR,0.1-25 C858 87-010-196-080 CHIP CAPACITOR,0.1-25

C635 87-A10-307-080 CAP,M 0.1-50 J C859 87-010-196-080 CHIP CAPACITOR,0.1-25

C636 87-A10-307-080 CAP,M 0.1-50 J C860 87-010-197-080 CAP, CHIP 0.01 DM
C637 87-A10-307-080 CAP,M 0.1-50 J C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C638 87-A10-307-080 CAP,M 0.1-50 J C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C639 87-010-405-080 CAP, ELECT 10-50V C961 87-010-152-080 C-CAP,S 8P-50 CH

–7–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z C105 87-010-415-040 CAP,E 10-50 5L
C971 87-010-381-080 CAP, ELECT 330-16V C106 87-010-493-040 CAP,E 0.47-50 GAS
C972 87-010-404-080 CAP, ELECT 4.7-50V C107 87-A10-189-040 CAP,E 220-10
C973 87-010-197-080 CAP, CHIP 0.01 DM C108 87-A10-189-040 CAP,E 220-10
C974 87-010-197-080 CAP, CHIP 0.01 DM C109 87-010-196-080 CHIP CAPACITOR,0.1-25

C979 87-010-322-080 C-CAP,S 100P-50 CH C110 87-010-178-080 CHIP CAP 1000P

C981 87-010-260-080 CAP, ELECT 47-25V C112 87-012-368-080 C-CAP,S 0.1-50 F
C982 87-010-196-080 CHIP CAPACITOR,0.1-25 C113 87-A10-354-080 C-CAP,S 0.047-50 K B
C983 87-010-197-080 CAP, CHIP 0.01 DM C114 87-010-196-080 CHIP CAPACITOR,0.1-25
C984 87-010-197-080 CAP, CHIP 0.01 DM C115 87-010-196-080 CHIP CAPACITOR,0.1-25

C987 87-010-197-080 CAP, CHIP 0.01 DM C116 87-010-196-080 CHIP CAPACITOR,0.1-25

C991 87-010-312-080 C-CAP,S 15P-50 CH C118 87-012-145-080 CAP, CHIP S 270P CH
C992 87-010-312-080 C-CAP,S 15P-50 CH C180 87-010-178-080 CHIP CAP 1000P
C993 87-010-178-080 CHIP CAP 1000P C181 87-010-178-080 CHIP CAP 1000P
C995 87-010-178-080 CHIP CAP 1000P C202 87-012-156-080 C-CAP,S 220P-50 CH

C997 87-010-196-080 CHIP CAPACITOR,0.1-25 C203 87-010-322-080 C-CAP,S 100P-50 CH

C998 87-010-260-080 CAP, ELECT 47-25V C204 87-012-157-080 C-CAP,S 330P-50 CH
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F C205 87-012-156-080 C-CAP,S 220P-50 CH
CF831 87-008-261-010 FILTER, SFE10.7MA5-A C214 87-010-322-080 C-CAP,S 100P-50 CH
CF832 87-008-261-010 FILTER, SFE10.7MA5-A C215 87-010-322-080 C-CAP,S 100P-50 CH

CN1 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3 C216 87-010-177-080 C-CAP,S 820P-50 SL

CN91 87-A60-109-010 CONN,2P V S2M-2W<EXCEPT 80U> C221 87-010-421-040 CAP,E 4.7-50 5L
CN101 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3 C222 87-010-421-040 CAP,E 4.7-50 5L
CN301 87-A60-620-010 CONN,3P V 2MM JMT C223 87-010-408-040 CAP,E 47-50 SME
CN351 87-A60-625-010 CONN,8P V 2MM JMT C224 87-012-369-080 C-CAP,S 0.047-50F

CN601 87-099-719-010 CONN,30P TYK-B(X) C312 87-010-498-040 CAP,E 10-16 GAS

CN602 87-099-194-010 CONN,6P 6216V C314 87-010-196-080 CHIP CAPACITOR,0.1-25
CNA1 8A-NF6-646-010 CONN ASSY,9P TID-A(460) C315 87-010-196-080 CHIP CAPACITOR,0.1-25
CNA2 8A-NF6-630-010 CONN ASSY,3P (VM) ANF-6 C316 87-010-196-080 CHIP CAPACITOR,0.1-25
CNA101 8A-NF6-670-010 CONN ASSY,2P (MUTE) ANF-6 C321 87-012-393-080 C-CAP,S 0.22-16 R K

CON301 87-NF6-615-010 CONN ASSY,3P PB C382 87-010-320-080 CHIP CAP 68P

CON351 87-NF6-616-010 CONN ASSY,8P RPB C383 87-010-196-080 CHIP CAPACITOR,0.1-25
FB501 87-008-372-080 FILTER, EMI BL OIRNI C384 87-010-196-080 CHIP CAPACITOR,0.1-25
FC602 88-906-621-110 FF-CABLE,6P 1.25 620MM C385 87-010-196-080 CHIP CAPACITOR,0.1-25
FFE831 A8-8ZA-190-030 8ZA-1 FEUNM C386 87-010-196-080 CHIP CAPACITOR,0.1-25

J102 87-A60-238-010 TERMINAL,SP 4P (MSC) C387 87-010-196-080 CHIP CAPACITOR,0.1-25

J103 87-A60-929-010 JACK,DIA6.3 BLK ST W/S TAI C392 87-010-320-080 CHIP CAP 68P
J601 87-A60-885-010 JACK,PIN 6P R/W MSC C402 87-010-196-080 CHIP CAPACITOR,0.1-25
J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 C403 87-010-322-080 C-CAP,S 100P-50 CH
L101 87-A50-610-010 COIL,1UH K(MDEC) C404 87-010-322-080 C-CAP,S 100P-50 CH

L102 87-A50-610-010 COIL,1UH K(MDEC) C405 87-010-322-080 C-CAP,S 100P-50 CH

L301 87-A50-049-010 COIL,TRAP 85K(COI) C406 87-010-322-080 C-CAP,S 100P-50 CH
L302 87-A50-049-010 COIL,TRAP 85K(COI) C407 87-010-322-080 C-CAP,S 100P-50 CH
L351 87-007-342-010 COIL,OSC 85K BIAS C408 87-010-322-080 C-CAP,S 100P-50 CH
L801 87-A50-540-010 COIL,FM DET(TOK) C461 87-010-196-080 CHIP CAPACITOR,0.1-25

L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) C462 87-010-196-080 CHIP CAPACITOR,0.1-25

L811 87-005-847-080 COIL,2.2UH(CECS) C463 87-010-196-080 CHIP CAPACITOR,0.1-25
L821 87-A50-209-010 COIL,1POLE MPX(MIT) C464 87-010-196-080 CHIP CAPACITOR,0.1-25
L822 87-A50-209-010 COIL,1POLE MPX(MIT) C465 87-010-196-080 CHIP CAPACITOR,0.1-25
L832 87-005-847-080 COIL,2.2UH(CECS) C652 87-010-183-080 C-CAP,S 2700P-50 B
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK)
C653 87-010-213-080 C-CAP,S 0.015-50 B
R161 87-A00-441-050 RES,270-1/2W J RP C701 87-010-406-040 CAP,E 22-50 SME
R162 87-A00-441-050 RES,270-1/2W J RP C802 87-012-154-080 C-CAP,S 150P-50 CH<EXCEPT 80U>
R163 87-A00-441-050 RES,270-1/2W J RP C804 87-010-187-080 CAP CHIP S5600P<EXCEPT 80U>
R164 87-A00-441-050 RES,270-1/2W J RP C805 87-010-196-080 CHIP CAPACITOR,0.1-25<EXCEPT 80U>

R790 87-010-197-080 CAP, CHIP 0.01 DM C806 87-010-401-040 CAP,E 1-50 SME<EXCEPT 80U>
R991 87-010-322-080 C-CAP,S 100P-50 CH C807 87-010-196-080 CHIP CAPACITOR,0.1-25<EXCEPT 80U>
R993 87-010-322-080 C-CAP,S 100P-50 CH C808 87-010-196-080 CHIP CAPACITOR,0.1-25<EXCEPT 80U>
R995 87-010-322-080 C-CAP,S 100P-50 CH C809 87-012-155-080 C-CAP 180P-50CH<EXCEPT 80U>
SFR351 87-A90-433-080 SFR,50K H NVZ6TLTA C810 87-010-263-040 CAP,E 100-10<EXCEPT 80U>

SFR352 87-A90-433-080 SFR,50K H NVZ6TLTA C811 87-010-545-040 CAP,E 0.22-50 SME<EXCEPT 80U>
WH1 87-A90-510-010 HLDR,WIRE 2.5-9P C812 87-010-405-040 CAP,E 10-50<EXCEPT 80U>
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309 CN101 87-099-720-010 CONN,30P TYK-B(P)
CN104 87-099-017-010 CONN, 15P 6216 V
CN301 87-099-195-010 CONN,7P 6216 V
FRONT C.B
CN604 87-099-210-010 CONN,5P 6216 H
C101 87-010-197-080 CAP, CHIP 0.01 DM CN901 87-A60-161-010 CONN,13P H FE
C102 87-010-322-080 C-CAP,S 100P-50 CH FB801 87-008-372-080 FILTER, EMI BL OIRNI<EXCEPT 80U>
C103 87-010-312-080 C-CAP,S 15P-50 CH FC104 88-915-111-110 FF-CABLE,15P 1.25
C104 87-012-157-080 C-CAP,S 330P-50 CH FC301 88-907-421-110 FF-CABLE,7P 1.25 420MM

–8–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
FC901 88-913-521-110 FF-CABLE,13P 1.25 520MM LED455 87-A40-496-040 LED,SLR-342MCT31 GRN
FL201 8A-NF6-601-010 FL,BJ750GNK 13G-35S ANF-6 LED456 87-A40-496-040 LED,SLR-342MCT31 GRN
L101 87-A50-333-010 COIL,OSC 9.43MHZ S349 87-A91-024-180 SW,TACT KSH0611BT
L801 87-A50-093-010 COIL,CLOCK 5.76MHZ<EXCEPT 80U> S350 87-A91-024-180 SW,TACT KSH0611BT
LED401 87-017-756-040 LED,SLR-342DCT31 ORN S351 87-A91-024-180 SW,TACT KSH0611BT

LED402 87-017-756-040 LED,SLR-342DCT31 ORN S352 87-A91-024-180 SW,TACT KSH0611BT

LED403 87-017-756-040 LED,SLR-342DCT31 ORN S353 87-A91-024-180 SW,TACT KSH0611BT
LED404 87-017-756-040 LED,SLR-342DCT31 ORN S354 87-A91-024-180 SW,TACT KSH0611BT
LED405 87-017-756-040 LED,SLR-342DCT31 ORN S355 87-A91-024-180 SW,TACT KSH0611BT
LED406 87-A40-496-040 LED,SLR-342MCT31 GRN

LED407 87-A40-496-040 LED,SLR-342MCT31 GRN MIC C.B

LED408 87-A40-496-040 LED,SLR-342MCT31 GRN
LED409 87-A40-496-040 LED,SLR-342MCT31 GRN C601 87-010-186-080 CAP,CHIP 4700P
LED410 87-A40-496-040 LED,SLR-342MCT31 GRN C602 87-010-405-040 CAP,E 10-50
LED416 87-A40-809-080 LED,LTL-307KK PGRN C603 87-010-320-080 CHIP CAP 68P
C604 87-010-546-040 CAP,E 0.33-50
LED417 87-A40-809-080 LED,LTL-307KK PGRN C606 87-010-112-040 CAP,E 100-16
LED418 87-A40-809-080 LED,LTL-307KK PGRN
LED419 87-A40-809-080 LED,LTL-307KK PGRN C607 87-010-196-080 CHIP CAPACITOR,0.1-25
LED420 87-A40-809-080 LED,LTL-307KK PGRN C608 87-010-178-080 CHIP CAP 1000P
LED421 87-A40-809-080 LED,LTL-307KK PGRN C621 87-010-178-080 CHIP CAP 1000P
CN603 87-099-212-010 CONN,5P 6216 V
LED425 87-017-756-040 LED,SLR-342DCT31 ORN FB601 87-008-372-080 FILTER, EMI BL OIRNI
LED426 87-017-756-040 LED,SLR-342DCT31 ORN
LED431 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF FC603 88-905-281-110 FF-CABLE, 5P 1.25 280MM
LED432 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF J601 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
LED433 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF J602 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM

LED440 87-A91-665-010 LED,SELU1E10 CXM-SLF55 BLUE

LED441 87-A91-665-010 LED,SELU1E10 CXM-SLF55 BLUE VM C.B
LED499 87-A40-317-080 LED,SLR-342VCT31 RED
S101 87-A91-591-010 SW,RTRY RE0121PVB25FINA24
S102 87-A91-664-010 SW,RTRY RE0121PVB30F AMP 1F C.B

S301 87-A91-024-180 SW,TACT KSH0611BT C101 87-010-178-080 CHIP CAP 1000P

S302 87-A91-024-180 SW,TACT KSH0611BT C102 87-010-178-080 CHIP CAP 1000P
S303 87-A91-024-180 SW,TACT KSH0611BT C103 87-010-545-080 CAP, ELECT 0.22-50V
S304 87-A91-024-180 SW,TACT KSH0611BT C104 87-010-545-080 CAP, ELECT 0.22-50V
S305 87-A91-024-180 SW,TACT KSH0611BT C107 87-016-145-080 CAP, ELECT 10-50 M 105 KME<80U>

S306 87-A91-024-180 SW,TACT KSH0611BT C107 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 80U>
S310 87-A91-024-180 SW,TACT KSH0611BT C108 87-016-145-080 CAP, ELECT 10-50 M 105 KME<80U>
S311 87-A91-024-180 SW,TACT KSH0611BT C108 87-010-405-080 CAP, ELECT 10-50V<EXCEPT 80U>
S312 87-A91-024-180 SW,TACT KSH0611BT C113 87-010-405-080 CAP, ELECT 10-50V
S313 87-A91-024-180 SW,TACT KSH0611BT C114 87-010-405-080 CAP, ELECT 10-50V

S314 87-A91-024-180 SW,TACT KSH0611BT<EXCEPT 80U> C115 87-A12-180-080 CAP, ELECT 10-63 M 105 KME<80U>
S321 87-A91-024-180 SW,TACT KSH0611BT C115 87-016-299-080 CAP,E 10-100 SME<EXCEPT 80U>
S322 87-A91-024-180 SW,TACT KSH0611BT C116 87-A12-180-080 CAP, ELECT 10-63 M 105 KME<80U>
S323 87-A91-024-180 SW,TACT KSH0611BT C116 87-016-299-080 CAP,E 10-100 SME<EXCEPT 80U>
S324 87-A91-024-180 SW,TACT KSH0611BT C119 87-010-197-080 CAP, CHIP 0.01 DM

S325 87-A91-024-180 SW,TACT KSH0611BT C120 87-010-197-080 CAP, CHIP 0.01 DM

S326 87-A91-024-180 SW,TACT KSH0611BT C133 87-010-190-080 C-CAP,S 0.01-50 ZF
S327 87-A91-024-180 SW,TACT KSH0611BT C153 87-010-188-080 C-CAP,S 6800P-50 B
S328 87-A91-024-180 SW,TACT KSH0611BT C201 87-A10-300-080 CAP,M 0.027-50 J
S329 87-A91-024-180 SW,TACT KSH0611BT<EXCEPT 80U> C202 87-A10-300-080 CAP,M 0.027-50 J

S330 87-A91-024-180 SW,TACT KSH0611BT<EXCEPT 80U> C203 87-A10-300-080 CAP,M 0.027-50 J

S331 87-A91-024-180 SW,TACT KSH0611BT<EXCEPT 80U> C204 87-A10-300-080 CAP,M 0.027-50 J
S332 87-A91-024-180 SW,TACT KSH0611BT<EXCEPT 80U> C205 87-010-180-080 C-CER 1500P
S333 87-A91-024-180 SW,TACT KSH0611BT C206 87-010-180-080 C-CER 1500P
S334 87-A91-024-180 SW,TACT KSH0611BT C207 87-010-401-080 CAP, ELECT 1-50V

S341 87-A91-024-180 SW,TACT KSH0611BT C208 87-010-401-080 CAP, ELECT 1-50V

S342 87-A91-024-180 SW,TACT KSH0611BT C209 87-010-187-080 CAP CHIP S5600P
S343 87-A91-024-180 SW,TACT KSH0611BT C210 87-010-187-080 CAP CHIP S5600P
S344 87-A91-024-180 SW,TACT KSH0611BT C211 87-016-142-080 CAP, ELECT 2.2-50 KME<80U>
S345 87-A91-024-180 SW,TACT KSH0611BT C211 87-010-402-080 CAP, ELECT 2.2-50V<EXCEPT 80U>

S346 87-A91-024-180 SW,TACT KSH0611BT C212 87-010-402-080 CAP, ELECT 2.2-50V

S347 87-A91-024-180 SW,TACT KSH0611BT C215 87-012-140-080 C-CAP,S 470P-50 J CH
C216 87-012-140-080 C-CAP,S 470P-50 J CH
C217 87-010-401-080 CAP, ELECT 1-50V
CD KEY C.B C218 87-016-141-080 CAP, ELECT 1-50 M 105 KME<80U>

CN302 87-099-195-010 CONN,7P 6216 V C218 87-010-401-080 CAP, ELECT 1-50V<EXCEPT 80U>
LED451 87-017-756-040 LED,SLR-342DCT31 ORN C221 87-010-405-080 CAP, ELECT 10-50V
LED452 87-017-756-040 LED,SLR-342DCT31 ORN C222 87-010-405-080 CAP, ELECT 10-50V
LED453 87-017-756-040 LED,SLR-342DCT31 ORN C223 87-010-197-080 CAP, CHIP 0.01 DM
LED454 87-A40-496-040 LED,SLR-342MCT31 GRN C224 87-010-197-080 CAP, CHIP 0.01 DM

–9–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C251 87-012-368-080 C-CAP,S 0.1-50 F C324 87-010-196-080 CHIP CAPACITOR,0.1-25
C252 87-012-368-080 C-CAP,S 0.1-50 F C325 87-010-186-080 CAP,CHIP 4700P
C253 87-010-196-080 CHIP CAPACITOR,0.1-25 C401 87-010-196-080 CHIP CAPACITOR,0.1-25
C254 87-010-196-080 CHIP CAPACITOR,0.1-25 C402 87-010-196-080 CHIP CAPACITOR,0.1-25
C401 87-010-260-080 CAP, ELECT 47-25V C403 87-010-405-080 CAP, ELECT 10-50V

CN101 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 C404 87-010-405-080 CAP, ELECT 10-50V
CN102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 CN101 87-099-195-010 CONN,7P 6216 V
CN106 87-099-195-010 CONN,7P 6216 V CN102 87-049-919-010 CONN,3P EH V WHT
CNA101 8A-NF6-645-010 CONN ASSY,5P TID-A(530) CN103 87-A60-619-010 CONN,2P V 2MM JMT
CNA102 8A-NF6-660-010 CONN ASSY,3P (SATE) ANF-6 J301 87-A61-189-010 JACK,3.5 MONO

FC106 88-907-151-110 FF-CABLE, 7P 1.25 150MM J302 87-A61-189-010 JACK,3.5 MONO

J201 87-A61-148-010 JACK,PIN 4P R/W BLUE L301 87-003-383-010 COIL,1UH-S
L251 87-003-383-010 COIL,1UH-S L302 87-003-383-010 COIL,1UH-S
L252 87-003-383-010 COIL,1UH-S
R129 87-A00-262-080 RES,M/F 0.15-2W J
PT C.B
R130 87-A00-262-080 RES,M/F 0.15-2W J
R231 87-A00-258-080 RES,M/F 0.22-1W J C1 87-010-387-080 CAP,E 470-25 SME
R232 87-A00-258-080 RES,M/F 0.22-1W J C4 87-A11-148-080 CAP,TC U 0.1-50 Z F
WH101 87-A90-459-010 HLDR,WIRE 2.5-5P C5 87-A11-148-080 CAP,TC U 0.1-50 Z F
C6 87-010-917-000 CAP,E 3300-50 M SMG
C7 87-010-917-000 CAP,E 3300-50 M SMG
AMP SATE C.B
C8 87-A11-148-080 CAP,TC U 0.1-50 Z F
C201 87-010-263-080 CAP, ELECT 100-10V C9 87-A11-148-080 CAP,TC U 0.1-50 Z F
C211 87-012-393-080 C-CAP,S 0.22-16 R K C10 87-A11-148-080 CAP,TC U 0.1-50 Z F
C212 87-012-393-080 C-CAP,S 0.22-16 R K C11 87-A11-148-080 CAP,TC U 0.1-50 Z F
C213 87-012-393-080 C-CAP,S 0.22-16 R K C12 87-016-520-000 CAP,E 3300-65 M SMG<80U>
C214 87-012-393-080 C-CAP,S 0.22-16 R K
C12 87-016-657-090 CAP,E 3300-71<EXCEPT 80U>
C215 87-010-196-080 CHIP CAPACITOR,0.1-25 C13 87-016-520-000 CAP,E 3300-65 M SMG<80U>
C216 87-010-196-080 CHIP CAPACITOR,0.1-25 C13 87-016-657-090 CAP,E 3300-71<EXCEPT 80U>
C217 87-012-141-080 CHIP-CAPACITOR,0.22-16F C16 87-010-403-080 CAP, ELECT 3.3-50V
C218 87-012-141-080 CHIP-CAPACITOR,0.22-16F CN1 87-A61-110-010 CONN,9P V TID-A
C219 87-010-184-080 CHIP CAPACITOR 3300P(K)
CN2 87-A61-108-010 CONN,5P V TID-A
C220 87-010-184-080 CHIP CAPACITOR 3300P(K) ! PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI<EXCEPT 80U>
C221 87-010-177-080 C-CAP,S 820P-50 SL ! PT2 8A-NF8-661-010 PT,SUB ANF-8 (U)<80U>
C222 87-010-177-080 C-CAP,S 820P-50 SL ! PT101 8A-NF6-622-010 PT,LH EI96-60 ANF-6<EXCEPT 80U>
C223 87-016-669-080 C-CAP,S 0.1-25 K B ! PT101 8A-NF6-621-010 PT,U EI96-60 ANF-6<80U>
C224 87-016-669-080 C-CAP,S 0.1-25 K B
! RY1 87-A91-281-010 RELAY,ACDC12V OSA-SS-212DM5<EX 80U>
C225 87-016-669-080 C-CAP,S 0.1-25 K B ! RY2 87-A90-976-010 RELAY,AC12V SDT-S-112LMR<80U>
C226 87-016-669-080 C-CAP,S 0.1-25 K B ! S1 87-A90-165-010 SW,SL 1-2-3 SWS2301<EXCEPT 80U>
C227 87-010-184-080 CHIP CAPACITOR 3300P(K) ! T1 87-A60-317-010 TERMINAL, 1P MSC
C228 87-010-184-080 CHIP CAPACITOR 3300P(K) ! T2 87-A60-317-010 TERMINAL, 1P MSC
C229 87-010-177-080 C-CAP,S 820P-50 SL

C230 87-010-177-080 C-CAP,S 820P-50 SL DECK C.B

C231 87-012-141-080 CHIP-CAPACITOR,0.22-16F
C232 87-012-141-080 CHIP-CAPACITOR,0.22-16F CON501 87-099-756-019 CONN,15P 9604S F
C233 87-010-374-080 CAP, ELECT 47-10V SFR1 87-024-581-010 SFR,3.3K DIA 6H
C234 87-010-374-080 CAP, ELECT 47-10V SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27
C235 87-010-544-080 CAP, ELECT 0.1-50V SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ
C236 87-010-544-080 CAP, ELECT 0.1-50V
C237 87-010-183-080 C-CAP,S 2700P-50 B SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ
C238 87-010-183-080 C-CAP,S 2700P-50 B SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
C239 87-010-544-080 CAP, ELECT 0.1-50V SW4 87-036-110-010 SW,MICRO SPPB62
SW5 87-036-110-010 SW,MICRO SPPB62
C240 87-010-544-080 CAP, ELECT 0.1-50V SW6 87-036-110-010 SW,MICRO SPPB62
C301 87-010-178-080 CHIP CAP 1000P
C302 87-010-178-080 CHIP CAP 1000P SW8 87-A90-248-010 SW,MICRO ESE11SH2CXQ
C303 87-010-544-080 CAP, ELECT 0.1-50V SW9 87-A90-248-010 SW,MICRO ESE11SH2CXQ
C304 87-010-544-080 CAP, ELECT 0.1-50V W1 82-ZM3-601-010 RBN-CORD,4P-75

C309 87-010-401-080 CAP, ELECT 1-50V

C310 87-010-401-080 CAP, ELECT 1-50V HEAD-1 C.B
C311 87-010-260-080 CAP, ELECT 47-25V
C312 87-010-260-080 CAP, ELECT 47-25V
C315 87-A10-596-080 C-CAP,S 100P-100 J CH HEAD-2 C.B

C316 87-A10-596-080 C-CAP,S 100P-100 J CH

C317 87-010-197-080 CAP, CHIP 0.01 DM
C318 87-010-197-080 CAP, CHIP 0.01 DM
C319 87-012-368-080 C-CAP,S 0.1-50 F
C320 87-012-368-080 C-CAP,S 0.1-50 F

C321 87-010-197-080 CAP, CHIP 0.01 DM

C322 87-010-197-080 CAP, CHIP 0.01 DM
C323 87-010-196-080 CHIP CAPACITOR,0.1-25

– 10 –
TRANSISTOR ILLUSTRATION

E C B E C B E C B B C E

KTA1266GR CC5551 CSC4115BC 2SB1370

KTC3198GR 2SB1370F
CD1585BC 2SD2061F
CSA952K

D C

G B
S E

E C B

DTC114ES 2SK2158 2SA1235F RT1P141C

KTC3199GR 2SJ461-T1 2SC2714O CSD1306E
2SA933S 2SC3052F KRA104S
CMBT5551 KRC102S-RTK
CMBT5401 KRA107S

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

– 11 –
WIRING – 1 (MAIN / VM)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 12 –
SCHEMATIC DIAGRAM – 1 (MAIN 1 / 3: AMP SECTION / VM)

– 13 –
SCHEMATIC DIAGRAM – 2 (MAIN 2 / 3: TUNER SECTION)

L802
AM IF ADJ.

/PB

– 14 –
SCHEMATIC DIAGRAM – 3 (MAIN 3 / 3: DECK SECTION)

– 15 –
WIRING – 2 (FRONT / CD KEY / MIC) <1 / 2>
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 16 –
WIRING – 2 (FRONT / CD KEY / MIC) <2 / 2>
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

– 17 –
SCHEMATIC DIAGRAM – 4 (FRONT / CD KEY / MIC)

IC401, 402
FRONT SHIFT REGISTER

– 18 –
WIRING – 3 (AMP 1F)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 19 –
SCHEMATIC DIAGRAM – 5 (AMP 1F)

– 20 –
WIRING – 4 (AMP SATE)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 21 –
SCHEMATIC DIAGRAM – 6 (AMP SATE)

– 22 –
WIRING – 5 (PT: U)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 23 –
SCHEMATIC DIAGRAM – 7 (PT: U)

– 24 –
WIRING – 6 (PT: LH, HA)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 25 –
SCHEMATIC DIAGRAM – 8 (PT: LH, HA)

– 26 –
WIRING – 7 (DECK)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 27 –
FL (BJ750GNK 13G-35S) GRID ASSIGNMENT & ANODE CONNECTION
GRID ASSIGNMENT

– 28 –
ANODE CONNECTION

– 29 –
IC BLOCK DIAGRAM

IC, M65849BFP631D

IC, BU2099FV

– 30 –
IC, M61506FP

IC, BU9990-03FS

– 31 –
IC, BA7762AFS

IC, LC72131D

– 32 –
IC, LA1843

IC, BU2092F

– 33 –
IC, BD3876KS2

– 34 –
IC DESCRIPTION
IC, LC87654V-5P35

Pin No. Pin Name I/O Description

1 O-CLK O CLOCK output for FRONT and MAIN C.B.
2 O-DATA O DATA output for FRONT and MAIN C.B.
3 O-STB(M) O Strobe output for MAIN C.B.
4 O-POWER O System power ON/OFF output.
5 O-STB(SHIFT) O Strobe output for shift register.
6 O-RYM-CS O Chip select output for RHYTHM IC.
7 O-PLL-CE O Chip enable output for PLL.
8 I-STEREO I Stereo detect input.
9 O-CLK SHIFT O Tuner clock shift output (active L).
10 I-HP-MUTE I Head phones connect detect input.
11 RESET I Reset input for MICON.
12 I-DISH I CD turntable photo sensor input.
13 I-SPEANA I SPEANA level AD input.
14 VSS1 – Connected to GND.
15 CF1 – To oscillator circuit.
16 CF2 – To oscillator circuit.
17 VDD1 – Power supply.
18 I-HOLD I HOLD input .
19 I-KEY1 I Key-1 AD input.
20 I-KEY2 I Key-2 AD input.
21 I-KEY3 I Key-3 AD input.
22 I-CDSW I CD nechanical switch input.
23 I-RTVR I Rotary encoder AD input for VR.
24 I-JOG I Rotary encoder AD input for MULTI JOG.
25 I-MIC I MIC input for AUTO VOCAL FADER.
26 I-MS I DECK MS detect input.

27 I-TM-BASE I Standard time input (8Hz).

28 I-WRQ I CD WRQ input.
29 I-RMC I System remote controller input.
30 ~ 42 G13 ~ G1 O FL grid output (G13 ~ G1).
43 ~ 45 P35 ~ P33 O FL segment output (P35 ~ P33).
46 VDD3 – Power supply.
47 P32/SPEANA-A O FL segment output (P32)/SPEANA band change output (A).
48 P31/SPEANA-B O FL segment output (P31)/SPEANA band change output (B).
49 P30/SPEANA-C O FL segment output (P30)/SPEANA band change output (C).
50 P29/BEAT-M O/I FL segment output (P29)/BEAT MASTER less diode input.
51 -VP – Connected to -VFL .
52 P28/AM-ST O/I FL segment output (P28)/AM-STEREO diode input (Not used).
53 P27/LW O/I FL segment output (P27)/LW diode input (Not used).
54 P26/SW O/I FL segment output (P26)/SW diode input (Not used).
55 P25/FM1 O/I FL segment output (P25)/FM1diode input (Not used).
56 P24/CASINO DEMO O/I FL segment output (P24)/initial CASINO DEMO diode input.

– 35 –
Pin No. Pin Name I/O Description
57 P23/ECO MODE O/I FL segment output (P23)/Initial ECO MODE less diode input.
58 P22/DSP O/I FL segment output (P22)/DSP less diode input (Not used).
59 P21/PRO/5.1 O/I FL segment output (P21)/PRO-LOGIC 5.1CH diode input (Not used).
60 P20/KEY-CON O/I FL segment output (P20)/KEY CONTROL diode input (Not used).
61 P19/DOLBY O/I FL segment output (P19)/DECK DOLBYdiode input (Not used).
62 P18/PRO O/I FL segment output (P18)/PROLOGIC diode input (Not used).
63 P17/AM10K O/I FL segment output (P17)/AM10 change diode input.
64 P16/CST2 O/I FL segment output (P16)/DECK 2 cassette detect SW input.
65 P15/REB O/I FL segment output (P15)/DECK side B record permission SW input.
66 P14/CAM2 O/I FL segment output (P14)/DECK 2 CAM SW input.
67 P13/AUTO1 O/I FL segment output (P13)/DECK 1 auto stop input.
68 P12/AUTO2 O/I FL segment output (P12)/DECK 2 auto stop input.
69 P11/CAM1 O/I FL segment output (P11)/DECK 1 CAM SW input.
70 P10/CST1 O/I FL segment output (P10)/DECK 1 cassette detect SW input.
71 P9/REA O/I FL segment output (P9)/DECK side A record permission SW input.
72 VDD4 – Power supply.
73 P8 /AC DEMO O/I FL segment output (P8)/DEMO less (on the shop) diode input (Not used).
74~80 P7~P1 O FL segment output (P7~P1).
81 NC – Not connected.
82 O-TRAY CLOSE O CD tray close output.
83 O-TRAY-OPEN O CD tray open output.
84 I-SUBQ I CD SUBQ detect input.
85 O-DISH-FWD O CD turntable forward revolution output.
86 O-DISH-REV O CD turntable reverse revolution output.
87 O-DATA O CD data output.
88 O-LED-STBY O STBY LED on output (STBY LED on during O-POWER OFF).
89 VSS2 – Connected to GND.
90 VDD2 – Power supply.
91 O-MOTOR O DECK motor output.
92 O-MUTE O System mute ON/OFF output.
93 O-SOL1 O DECK 1 plunger ON/OFF output.
94 O-SOL2 O DECK 2 plunger ON/OFF output.
95 I-DRF I CD DRF input.

96 I-IFC I TUNER IFC input.

97 NC – Connected to GND.
98 O-CD CLK O CD CLK output.
99 O-CD-CE O CD CE output.
100 O-KSCAN O Key scan timing output.

– 36 –
ADJUSTMENT <TUNER / DECK / FRONT>

A MAIN C.B 7 6 1 7

SFR352 SFR351
L802
L801
IC801 TP4 (DC BALANCE)
12
TP3 (DC BALANCE)
L951
TP2 (CLK)
4
(3/3) (1/3)

TP1 (VT) 2
3
GND
FFE831
4 9 TP5 (LCH)
5 10 TP6 (RCH)
6 11
7 12
8 13

B FRONT C.B

FL101

IC101

TP7
L101
TP8(GND)

14

DECK–1 P HEAD
DECK–2 R/P/E HEAD I DECK C.B

SFR1

9 9
FWD REV 8

– 37 –
< TUNER SECTION > < DECK SECTION >
1. Clock frequency Check 8. Tape Speed Adjustment (DECK 2)
Settings : • Test point : TP2 Settings : • Test tape : TTA–100
Method : Set to AM 1710kHz and check that the test point is • Test point : TP5(Lch), TP6(Rch)
2160kHz ± 45Hz. • Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
2. AM VT Check frequency counter reads 3000Hz ± 5Hz and ±45Hz
Settings : • Test point : TP1 (VT) (REV) with respect to forward speed.
Method : Set to AM 1710kHz, 530kHz and check that the test
point is less than 8.5V (1710kHz) and more than 9. Head Azimuth Adjustment (DECK 1, DECK 2)
0.6V (530kHz). Settings : • Test tape : TTA–330
• Test point : TP5(Lch), TP6(Rch)
3. FM VT Check • Adjustment location : Head azimuth
Settings : • Test point : TP1 (VT) adjustment screw
Method : Set to FM 87.5MHz, 108.0MHz and check Method : Play back (FWD) the 8kHz signal of the test tape
that the test point is more than 0.5V (87.5MHz) and and adjust screw so that the output becomes
less than 8.0V (108.0MHz). maximum. Next, perform on REV PLAY mode.

4. AM Tracking Adjustment 10. PB Frequency Response Check (DECK 1, DECK 2)

Settings : • Test point : TP5(Lch), TP6(Rch) Settings : • Test tape : TTA–300
• Adjustment location : • Test point :TP5(Lch), TP6(Rch)
L951(1/3) ...................................... 1000kHz Method : Play back the 315Hz and 10kHz signals of the test
Method : Set to AM 1000kHz and adjust L951(1/3) to MAX. tape and check that the output ratio of the 10kHz
signal with respect to that of the 315Hz signal is
5. FM Tracking Check 0dB ± 3dB.
Settings : • Test point : TP5(Lch), TP6(Rch)
Method : Set to FM 98.0MHz and check that the test point is 11. PB Sensitivity Check (DECK 1, DECK 2)
less than 9dBµV. Settings : • Test tape : TTA–200
• Test point : TP5(Lch), TP6(Rch)
6. AM IF Adjustment Method : Play back the test tape and check that the output
Settings : • Test point : TP5(Lch), TP6(Rch) level of the test point is 400mV ± 3dB.
• Adjustment location :
L802 ................................................ 450kHz 12. REC/PB Frequency Response Adjustment (DECK 2)
Settings : • Test tape : TTA–602
7. DC Balance / Mono Distortion Adjustment • Test point : TP5(Lch), TP6(Rch)
Settings : • Test point : TP3, TP4 (DC Balance) • Input signal : 1kHz / 10kHz (LINE IN)
: TP5(Lch), TP6(Rch) (Distortion) • Adjustment location : SFR351 (Lch)
• Adjustment location : L801 SFR352 (Rch)
• Input level : 60dBµV Method : Apply a 1kHz signal and REC mode. Then adjust
Method : Set to FM 98.0MHz and adjust L801 so OSC attenuator so that the output level at the TP5,
that the voltage between TP3 and TP4 TP6 becomes 28mV. Record and play back the 1kHz
becomes 0V ± 0.04V. and 10kHz signals and adjust SFRs so that the output
Next, check that the distortion is less than of the 10kHz signals becomes 0dB ± 0.5dB with
1.3%. respect to that of the 1kHz signal.

13. REC/PB Sensitivity Check (DECK 2)

Settings : • Test tape : TTA–602
• Test point : TP5(Lch), TP6(Rch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust
OSC attenuator so that the output level at TP5, TP6
becomes 280mV. Record and play back the 1kHz
signals and check that the output is –1dB ± 3.0dB.

< FRONT SECTION >

14. µ-CON OSC Adjustment

Settings : • Test point : TP7 and TP8 (GND)
• Adjustment location : L101
Method : Insert AC plug while pressing TUNER function key.
Adjust L101 so that the frequency at the test point is
208.80Hz ± 0.2Hz.

– 38 –
MECHANICAL EXPLODED VIEW 1 / 1

47
C 62
59 B
B 60
K K B
20 B J J
58
K
B
K 57 c

B
c
P.C.B 61 63
B B
48 G
56
49 L 54
i 66 M M M
K G h
55 B
K g 64
46 29 f HT-SINK
b I B 56
PLATE,PT
G CHAS,MAIN e d 65
K 50
45 44 h B i
43
42 e g B P.C.B
FL201 P.C.B HT-SINK 53 B

B B
25 52
P.C.B D
B
f N G
24 41
40 B
28 23 39 P.C.B G C
51
H 30
d
PLATE,SHLD MECHA
34
14 b AZG-1 ZD3RNDM
21
38 33 B
12 37
36
35 67
E 8 24 32
27
26 F A 23 31 B
22 B
21
a P.C.B 68
P.C.B a B
7 B
10 6 B B
E 20 69
F
B PLATE,EARTH MIC 2ZM-3MK2 PR7NM
SH,CD
13
5 19
11 18
3 17
4 15 16
2 9
1 15

– 39 –
MECHANICAL PART LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NF6-010-010 PANEL,DIRECT 45 8A-NF6-042-010 REFLECTOR,ECO
2 8A-NF6-044-010 REFLECTOR,CD 46 8A-NF6-004-010 CABI,STEEL
3 8A-NF6-205-010 GUIDE,CD 47 8A-NF6-005-010 PANEL,TOP
4 8A-NF6-009-010 PANEL,CD 48 87-NF6-616-010 CONN ASSY,8P RPB
5 8A-NF6-037-010 KEY,CD OPEN 49 87-NF6-615-010 CONN ASSY,3P PB

6 8A-NF6-035-010 KEY,CD DIRECT 50 8A-NF8-206-010 HLDR,PWB M

7 8A-NF6-036-010 KEY,CD EDIT 51 8A-NF6-214-010 HLDR,HT-SINK R
8 8A-NF6-002-010 CABI,FR H<EXCEPT 80U> 52 88-907-151-110 FF-CABLE, 7P 1.25 150MM
8 8A-NF6-001-010 CABI,FR U<80U> 53 8A-NF6-210-010 HLDR,IC6
9 8A-NF6-019-010 WINDOW,CASS 2 54 8A-NF7-226-010 HLDR,IC2-T2

10 8A-NF6-018-010 WINDOW,CASS 1 55 8A-NF6-213-010 HLDR,HT-SINK L

11 8A-NF6-007-010 BOX,CASS 2 56 87-NF4-221-010 HLDR,CABLE
12 8A-NF6-006-010 BOX,CASS 1 57 87-A91-711-010 FAN,3110GL-B4W-B34-H02<EXCEPT 80U>
13 82-NF5-219-010 SPR-T,EJECT 2 (SIN) 58 8A-NF6-219-010 HLDR,FAN<EXCEPT 80U>
14 82-NF5-218-010 SPR-T,EJECT 1 (SIN) 59 8A-NF6-052-010 PANEL,REAR LH<EXCEPT 80U>

15 8A-NF6-030-010 KNOB,RTRY JOG 59 8A-NF6-051-010 PANEL,REAR U<80U>

16 8A-NF6-040-010 REFLECTOR,VOL 60 87-084-077-010 NYLON RIVET, 3.5-4.5
17 8A-NF6-041-010 RING,VOL 61 8A-NF6-082-010 COVER, REAR LHSM<80LH>
18 8A-NF6-029-010 KEY,GEQ 61 8A-NF6-087-010 COVER, REAR LHSM Z83<83LH>
19 88-905-281-110 FF-CABLE, 5P 1.25 280MM 61 8A-NF6-086-010 COVER, REAR SPEC LABEL<80HA>

20 87-064-185-010 HLDR,WIRE 61 8A-NF6-110-010 COVER,REAR ST USM<80U>

21 8Z-NF6-210-010 DMPR,150 N 62 8A-NF6-217-010 HLDR,PWB PT<80LH,83LH>
22 87-NF4-217-110 HLDR,LOCK 2 62 8A-NF6-228-010 HLDR,PWB PT 96-75<80U,80HA>
23 86-NF9-224-010 SPR-C,LOCK 63 8A-NF6-622-010 PT,LH EI96-60 ANF-6<EXCEPT 80U>
24 82-NF5-229-010 PLATE,LOCK ! 63 8A-NF6-621-010 PT,U EI96-60 ANF-6<80U>

25 87-NF4-216-010 HLDR,LOCK 1 ! 64 87-A80-105-010 AC CORD ASSY,AZ<80HA>

26 8A-NF6-012-010 PANEL,FR H<EXCEPT 80U> 64 87-A80-092-010 AC CORD ASSY,E BLK SUN<80LH,83LH>
26 8A-NF6-011-010 PANEL,FR U<80U> ! 64 87-A80-110-010 AC CORD ASSY,U SPT-2W<80U>
27 81-532-080-010 LABEL, CASS. COMPT 65 87-085-185-010 BUSHING, AC CORD (E)<EXCEPT 80U>
28 8A-NF6-059-010 WIND0W,DISP H Z80E<80HA> 65 87-085-189-010 BUSHING, CORD (U)<80U>

28 8A-NF6-016-010 WINDOW,DISPLAY H<80LH> 66 8A-NF7-209-010 HLDR,PWB-M BTM

28 8A-NF6-014-010 WINDOW,DISPLAY H Z83<83LH> 67 84-ZG1-245-210 CAP,OPTICAL
28 8A-NF6-015-010 WINDOW,DISPLAY U<80U> 68 8A-NF6-008-010 PANEL,TRAY
29 88-906-621-110 FF-CABLE,6P 1.25 620MM 69 8A-NF6-003-010 CABI,BOTTOM
30 88-913-521-110 FF-CABLE,13P 1.25 520MM A 87-067-758-010 BVT2+3-12 W/O SLOT

31 8A-NF6-204-010 GUIDE,DECK B 87-067-703-010 TAPPING SCREW, BVT2+3-10

32 8A-NF6-039-010 REFLECTOR,DECK C 87-067-688-010 BVTT+3-6
33 88-915-111-110 FF-CABLE,15P 1.25 D 87-591-095-410 TAPPING SCREW, QIT+3-8 (GLD)
34 88-907-421-110 FF-CABLE,7P 1.25 420MM E 87-591-094-410 TAPPING SCREW, QIT+3-6
35 8A-NF6-022-010 KEY,ECHO F 87-721-097-410 QT2+3-12 GLD

36 8A-NF6-031-010 KEY,BBE U<EXCEPT 80U> G 87-067-579-010 TAPPING SCREW, BVT2+3-8

36 8A-NF6-047-010 KEY,T-BASS U<80U> H 87-723-096-410 QT2+3-10W/O SLOT BL
37 8A-NF6-034-010 KEY,SPICE<EXCEPT 80U> I 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
38 8A-NF6-038-010 REFLECTOR,FL J 87-067-975-010 S-SCREW,IT+4-8
39 8A-NFT-007-010 KEY,ASSY PRO K 87-B10-091-010 UTT2+3-10 W/O BLK

40 8A-NF6-026-010 KEY,ASSY OPE L 87-067-001-010 S-SCREW,BVWWST2+3-12W/O SL

41 8A-NF6-203-010 GUIDE,OPE M 87-078-191-010 S-SCREW,IT+4-10
42 8A-NF6-201-010 GUIDE,FL N 87-067-581-010 TAPPING SCREW, BVT2+3-15
43 8A-NF6-023-010 KEY,ASSY FUN
44 8A-NF6-045-010 KEY,ASSY POWER

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange

– 40 –
TAPE MECHANISM EXPLODED VIEW 1 / 1

14 B
15
B

42 PH(DECK 1) 51
RPH(DECK 2)
16 SOL 2 DECK C.B
A
8
52
12
13
8 50
17
56 SOL 1
11 10 A
18 49

(DECK 2) 44

9 41
50
7
B
47
43

3
35
18
48 41
(DECK 1)
19
E
2
37
33 45
5 6
36
A
20
4
46 31 34

HEAD 1 C.B(DECK 1)
HEAD 2 C.B(DECK 2) 22 32 58 D
D
C
A 40
21
30 55
29 24
(DECK 1)
(DECK 2)
39
25 B

23 29 (DECK 2)
26 D 38

C
A 27

28
C 54
53 57

– 41 –
TAPE MECHANISM PART LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 82-ZM3-301-619 CHAS ASSY,M2 35 82-ZM1-265-310 SPR-E,TRIG
2 82-ZM1-258-219 SPR-T,PINCH L 36 82-ZM1-236-019 CAPSTAN N 2-41.5
3 82-ZM1-341-219 LVR ASSY,PINCH L2 37 82-ZM1-239-019 CAPSTAN N 2.2-41.7
4 82-ZM1-333-110 PLATE,LINK 2 38 82-ZM1-322-019 SPR-T,FR60
5 82-ZM1-266-310 LVR,DIR 39 82-ZM1-220-219 GEAR,IDLER

6 82-ZM1-214-919 SPR-T,DIR 40 82-ZM3-616-019 RING MAGNET 4

7 82-ZM1-206-81K CHAS,HEAD 41 82-ZM1-216-519 GEAR,REEL
8 82-ZM3-307-019 CUSH-G,DIA3.7-8-3.2 42 87-A91-196-010 HEAD,PH KP9142
9 82-ZM1-269-219 SPR-T,BRG 42 87-A91-195-010 HEAD,RPH KC9142
10 82-ZM1-219-119 SPR-T,LINK 43 82-ZM1-225-21K GEAR,FR

11 82-ZM1-210-119 GEAR,H T 44 82-ZM1-226-019 GEAR,REW

12 82-ZM3-353-010 SPR-T,HEAD 45 82-ZM3-333-310 SLIP DISK ASSY 2
13 82-ZM1-207-919 GUIDE,TAPE 46 82-ZM1-338-110 BELT FR4
14 86-ZM4-206-110 S-SCREW,AZIMUTH 47 82-ZM1-349-110 FLY-WHL,R W(DECK 2)
15 82-ZM1-314-119 PLATE,HEAD 47 82-ZM3-338-310 FLY-WHL,R3 W(DECK 1)

16 82-ZM1-208-319 HLDR,HEAD 48 82-ZM1-348-110 FLY-WHL,L W(DECK 2)

17 82-ZM1-218-019 SPR-E,HB 48 82-ZM1-348-110 FLY-WHL,L W(DECK 1)
18 82-ZM1-263-110 LVR,EJECT L (DECK 1) 49 82-ZM3-329-410 BELT,SBU R2
18 82-ZM1-264-010 LVR,EJECT R (DECK 2) 50 82-ZM1-245-210 HLDR,IC
19 82-ZM1-222-21K LVR,PLAY 51 87-045-347-019 MOT,SHU2L 70(M1)

20 82-ZM1-217-419 REEL TABLE 52 82-ZM3-221-210 PULLEY,MOT 2M

21 82-ZM1-244-510 SPR-C,BT 53 82-ZM1-288-019 SH,1.63-3.2-0.5 SLT
22 82-ZM1-285-410 SPR-C,BT L 54 80-ZM6-243-019 SH,1.75-3.6-0.5 SLT
23 82-ZM1-257-019 SPR-T,CAS 55 82-ZM3-335-310 PULLEY,COUPLER M3(DECK 1)
24 82-ZM1-241-319 LVR,MC 56 82-ZM3-342-010 BELT,SBU MOT 2

25 82-ZM1-242-019 LVR,CAS 57 82-ZM3-339-110 SHAFT,COUPLER N3(DECK 1)

26 82-ZM1-243-019 LVR,STOP 58 86-ZM1-206-010 BELT,MAIN L
27 82-ZM1-344-219 LVR ASSY,PINCH R2 A 85-ZM3-202-010 S-SCREW,TG
28 82-ZM1-259-219 SPR-T,PINCH R B 80-ZM6-207-110 V+1.6-7
29 82-ZM1-240-119 LVR,REC (DECK 2) C 82-ZM3-318-110 S-SCRW MOTOR M2

30 82-ZM3-340-010 SH,BELT D2 D 87-B10-043-010 W-P,0.99-4-0.25 SLT

31 82-ZM1-255-319 SPR-E,LVR DIR E 82-ZM3-334-010 PW,2.16-6-0.4
32 82-ZM3-305-310 GEAR,CAM M2
33 82-ZM1-227-319 LVR,TRIG
34 82-ZM3-306-11K LVR,FR M2

– 42 –
SPRING APPLICATION POSITION

82-ZM1-257-019 82-ZM1-218-019
SPR-T,CAS SPR-E,HB

82-ZM1-285-419
82-ZM1-244-510
SPR-C,BT L
SPR-C,BT

82-ZM1-219-119
SPR-T,LINK

82-ZM1-259-219
SPR-T,PINCH R

82-ZM1-258-210
SPR-T,PINCH L

82-ZM3-353-010 82-ZM1-269-219 82-ZM1-214-010

SPR-T,HEAD SPR-T,BRG SPR-T,DIR

82-ZM1-322-019
SPR-T,FR 60

82-ZM1-265-310
SPR-E,TRIG

82-ZM1-255-319
SPR-E,LER DIR

– 43 –
SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1 Type.4
Insert a flat-bladed screwdriver into the position indicated by the TOOLS
arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer
unit and then remove the speaker units.
2 (() flat head screwdriver
3 Cut chisel

1 2 3

How to Remove the PANEL, FR

Type.2
1. Insert the (() flat head screwdriver tip into the gap
Remove the grill frame and four pieces of rubber caps by pulling between the PANEL, FR and the PANEL, SPKR. Tap the
out with a flat-bladed screwdriver. Remove the screws from hole head of the (() flat head screwdriver with the plastic
where installed rubber caps. Insert a flat-bladed screwdriver into hammer head, and create the clearance as shown in Fig-1.
the position indicated by the arrows and remove the panel. Re-
move the screws of each speaker unit and then remove the speaker 2. Insert the cut chisel in the clearance, and tap the head of
units. the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.

3. Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.

Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counter-
clockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise Fig-1 Fig-2
direction until "click" sound comes out.

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.

– 44 –
SPEAKER PARTS LIST SX-WNSZ80 (YLSL,YLSC9)

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NS0-001-010 PANEL,FR 11 88-NS5-610-010 CORD,SPKR
2 8A-NS0-004-010 PANEL,DUCT 12 88-NS5-611-010 CORD,SPKR B/L
3 8A-NS0-005-010 PANEL,TOP 13 8A-NS6-002-010 PANEL,FR(SX-S80)
4 8A-NS0-006-010 PANEL,NAME 14 8A-NS6-004-010 GRILLE,FRAME ASSY(SX-S80)
5 8A-NS0-007-010 GRILLE,FRAME ASSY 15 8A-NS6-610-010 CORD,3.5(SX-S80)

6 8A-NS0-010-010 PROTECTOR,TWA 16 8A-NS6-606-010 SPKR,80(SX-S80)

7 8A-NS0-011-010 HLDR,PIEZO
8 8A-NS6-602-010 SPKR,W 200
9 8A-NS0-604-010 SPKR,M 120
10 88-NSK-610-010 SPKR,CERAMIC ASSY

SPEAKER PARTS LIST SX-WNH83 (YLML)

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NSY-001-010 PANEL,FR R 11 8A-NS6-004-010 GRILLE,FRAME ASSY(SX-S80)
2 8A-NSY-002-010 PANEL,FR L 12 8A-NS6-610-010 CORD,3.5(SX-S80)
3 8A-NSY-003-010 PANEL,BA R 13 8A-NS6-606-010 SPKR,80(SX-S80)
4 8A-NSY-004-010 PANEL,BA L 14 8A-NSY-010-010 CABI,M
5 8A-NSY-005-010 GRILLE,FRAME ASSY 15 8A-NSY-011-010 RING,W

6 8Z-NS5-602-010 SPKR,W 200 16 8A-NSY-012-010 COVER,REAR

7 8A-NS0-604-010 SPKR,M 120
8 88-NS5-610-010 CORD,SPKR
9 88-NS5-611-010 CORD,SPKR B/L
10 8A-NS6-002-010 PANEL,FR(SX-S80)

SPEAKER PARTS LIST SX-WNAJ85 (YUSL)

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NS2-001-010 PANEL,FR 11 88-NS5-610-010 CORD,SPKR
2 8A-NS2-002-010 PANEL,TW R 12 88-NS5-611-010 CORD,SPKR B/L
3 8A-NS2-003-010 PANEL,TW L 13 8A-NS6-002-010 PANEL,FR(SX-S80)
4 8A-NS2-004-010 PANEL,DUCT 14 8A-NS6-004-010 GRILLE,FRAME ASSY(SX-S80)
5 8A-NS2-013-010 PANEL,DUCT RING 15 8A-NS6-610-010 CORD,3.5(SX-S80)

6 8A-NS2-008-010 PROTECTOR,TW 16 8A-NS6-606-010 SPKR,80(SX-S80)

7 8A-NS2-009-010 GRILLE,FRAME ASSY
8 8A-NS6-604-010 SPKR,W 200
9 8A-NS0-604-010 SPKR,M 120
10 88-NSK-610-010 SPKR,CERAMIC ASSY

– 45 –
ACCESSORIES / PACKAGE LIST

REF. NO. PART NO. KANRI DESCRIPTION

NO.
1 8A-NF6-902-010 IB,LH(ESP)M<80LH,80HA>
1 8A-NF6-912-010 IB,LH(ESP)M 83<83LH>
1 8A-NF6-903-010 IB,U(ESF)M<80U>
2 8Z-NF8-701-210 RC UNIT,RC-ZAS01
3 87-006-225-010 AM LOOP ANT NC2

4 87-043-115-010 ANT,FEEDER FM
! 5 87-A91-017-010 PLUG,CONVERSION JT-0476<80LH,83LH>

– 46 –
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9420208 0251431 Printed in Singapore
 AZG-1 English

SERVICE MANUAL
CD-R/RW MECHANISM BASIC CD MECHANISM:KSM-880CAB

TYPE
ZD8RD
YZD8RMDJM
ZD8RMDJM
ZD8RDNDM
YKZD8RDF
ZD8RDM
YZD8RDM
ZD8RN1DM
YZD8RDJM
TA
DA

S/M Code No. 09-001-335-3N6

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-
CLASS 1 LASER PRODUCT
tävälle näkymättömälle lasersäteilylle. KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.

Precaution to replace Optical block

Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.

1) After the connection, remove solder shown in

the figure below.

Solder

2
How to Adjust the Rotating Phase of the
Gear, Main Cam
1) Push down the hooking catch of the CHAS. MECH, and
remove the TRAY.
2) Align the arrow mark of the Gear, Main Cam with the black
round mark of the CHAS, MECHA as shown below.
3) Confirm that the Slide, Mech Cam is located in the right
position, then insert the TRAY gently.

Caution: If the rotating phase of the Gear, Main Cam is

incorrectly adjusted, the chucking operation and
tray movement will have malfunction.

Align the arrow 2 mark with the black

round • mark.

3
ELECTRICAL MAIN PARTS LIST

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C109 87-010-992-080 C-CAP,S 0.047-25 B
C110 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A21-381-040 C-IC,LA9235M <YKZD88RDF,ZD8RD>
87-A21-556-010 C-IC,LC78641E C110 87-010-196-020 CHIP CAPACITOR,0.1-25
87-A21-414-010 IC,BA5927S <EXCEPT YKZD88RDF,ZD8RD>
C111 87-010-260-080 CAP, ELECT 47-25V
C112 87-010-197-020 CHIP CAPACITOR,0.01-25
TRANSISTOR <EXCEPT YKZD88RDF,ZD8RD>

87-026-609-080 TR,KTA1266GR C112 87-010-197-080 CHIP CAPACITOR,0.01-25

87-A30-076-080 C-TR,2SC3052F <YKZD88RDF,ZD8RD>
87-A30-497-080 TR,2SA1980Y/G C114 87-010-260-080 CAP, ELECT 47-25V
87-A30-087-080 C-FET,2SK2158 C115 87-010-197-080 CHIP CAPACITOR,0.01-25
87-026-237-080 CHIP-TR,DTC124XK <YKZD88RDF,ZD8RD>
<EXCEPT ZD8RN1DM,YZD8RDM> C115 87-010-197-020 CHIP CAPACITOR,0.01-25
<EXCEPT YKZD88RDF,ZD8RD>
87-A30-075-080 C-TR,2SA1235F C116 87-010-260-080 CAP, ELECT 47-25V

C117 87-010-197-080 CHIP CAPACITOR,0.01-25

DIODE <YKZD88RDF,ZD8RD>
C117 87-010-197-020 CHIP CAPACITOR,0.01-25
87-A40-270-080 C-DIODE,MC2838 <EXCEPT YKZD88RDF,ZD8RD>
87-070-136-080 ZENER,MTZJ5.1B C118 87-010-260-080 CAP, ELECT 47-25V
87-A40-003-080 ZENER,MTZJ4.3A C119 87-015-819-080
87-A40-337-080 ZENER,MTZJ6.8B C120 87-010-312-080 C-CAP,S 15P-50 CH
87-A40-313-080 C-DIODE,MC2840 <YKZD88RDF,ZD8RD>

C120 87-010-312-020 C-CAP,S 15P-50 CH

3CD C.B <EXCEPT YKZD88RDF,ZD8RD>
C121 87-010-312-020 C-CAP,S 15P-50 CH
C1 87-010-374-080 CAP,E 47-10 <EXCEPT YKZD88RDF,ZD8RD>
C2 87-010-196-020 CHIP CAPACITOR,0.1-25 C121 87-010-312-080 C-CAP,S 15P-50 CH
<EXCEPT YKZD88RDF,ZD8RD> <YKZD88RDF,ZD8RD>
C2 87-010-196-080 CHIP CAPACITOR,0.1-25 C122 87-010-404-080 CAP, ELECT 4.7-50V
<YKZD88RDF,ZD8RD> C123 87-010-197-020 CHIP CAPACITOR,0.01-25
C3 87-010-260-080 CAP, ELECT 47-25V <EXCEPT YKZD88RDF,ZD8RD>
C4 87-010-260-080 CAP, ELECT 47-25V
C123 87-010-197-080 CHIP CAPACITOR,0.01-25
C5 87-010-197-020 CHIP CAPACITOR,0.01-25 <YKZD88RDF,ZD8RD>
<EXCEPT YKZD88RDF,ZD8RD> C124 87-010-401-080 CAP, ELECT 1-50V
C5 87-010-197-080 CHIP CAPACITOR,0.01-25 C126 87-010-196-020 CHIP CAPACITOR,0.1-25
<YKZD88RDF,ZD8RD> <EXCEPT YKZD88RDF,ZD8RD>
C6 87-010-405-080 CAP, ELECT 10-50V C126 87-010-196-080 CHIP CAPACITOR,0.1-25
C7 87-010-263-080 CAP, ELECT 100-10V <YKZD88RDF,ZD8RD>
C8 87-012-349-080 C-CAP,S 1000P-50 CH C128 87-010-196-020 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD>
C10 87-010-546-080 CAP,E 0.33-50
C11 87-010-401-080 CAP, ELECT 1-50V C128 87-010-196-080 CHIP CAPACITOR,0.1-25
C13 87-010-321-020 C-CAP,S 82P-50 CH <YKZD88RDF,ZD8RD>
<EXCEPT YKZD88RDF,ZD8RD> C130 87-010-196-080 CHIP CAPACITOR,0.1-25
C13 87-010-321-080 C-CAP,S 82P-50 J CH <YKZD88RDF,ZD8RD>
<YKZD88RDF,ZD8RD> C130 87-010-196-020 CHIP CAPACITOR,0.1-25
C15 87-010-197-020 CHIP CAPACITOR,0.01-25 <EXCEPT YKZD88RDF,ZD8RD>
<EXCEPT YKZD88RDF,ZD8RD> C132 87-010-405-080 CAP, ELECT 10-50V
C133 87-010-314-020 C-CAP,S 22P-50V
C15 87-010-197-080 CHIP CAPACITOR,0.01-25 <EXCEPT YKZD88RDF,ZD8RD>
<YKZD88RDF,ZD8RD>
C16 87-010-260-080 CAP, ELECT 47-25V C133 87-010-314-080 C-CAP,S 22P-50V<YKZD88RDF,ZD8RD>
C101 87-010-992-080 C-CAP,S 0.047-25 B C135 87-A11-088-080 CAP,TC U 100P-50 J CH
C102 87-010-401-080 CAP, ELECT 1-50V C151 87-010-405-080 CAP, ELECT 10-50V
C103 87-010-196-020 CHIP CAPACITOR,0.1-25 C152 87-010-405-080 CAP, ELECT 10-50V
<EXCEPT YKZD88RDF,ZD8RD> C192 87-012-349-080 C-CAP,S 1000P-50 CH

C103 87-010-196-080 CHIP CAPACITOR,0.1-25 C193 87-010-196-080 CHIP CAPACITOR,0.1-25

<YKZD88RDF,ZD8RD> <YKZD88RDF,ZD8RD>
C104 87-010-196-020 CHIP CAPACITOR,0.1-25 C193 87-010-196-020 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD> <EXCEPT YKZD88RDF,ZD8RD>
C104 87-010-196-080 CHIP CAPACITOR,0.1-25 C201 87-A10-730-080 CAP,E 1000-16 SMG
<YKZD88RDF,ZD8RD> C202 87-010-196-080 CHIP CAPACITOR,0.1-25
C105 87-010-260-080 CAP, ELECT 47-25V <YKZD88RDF,ZD8RD>
C106 87-010-322-020 C-CAP,S 100P-50 CH C202 87-010-196-020 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD> <EXCEPT YKZD88RDF,ZD8RD>

C106 87-010-322-080 C-CAP,S 100P-50 CH C204 87-010-196-020 CHIP CAPACITOR,0.1-25

<YKZD88RDF,ZD8RD> <EXCEPT YKZD88RDF,ZD8RD>
C107 87-010-196-020 CHIP CAPACITOR,0.1-25 C204 87-010-196-080 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD> <YKZD88RDF,ZD8RD>
C107 87-010-196-080 CHIP CAPACITOR,0.1-25 C205 87-010-405-080 CAP, ELECT 10-50V
<YKZD88RDF,ZD8RD> C206 87-010-405-080 CAP, ELECT 10-50V
C108 87-010-186-080 CAP,CHIP 4700P<YKZD88RDF,ZD8RD> C207 87-010-196-020 CHIP CAPACITOR,0.1-25
C108 87-010-186-020 CAP,CHIP 4700P <EXCEPT YKZD88RDF,ZD8RD>
<EXCEPT YKZD88RDF,ZD8RD>

4
 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
C207 87-010-196-080 CHIP CAPACITOR,0.1-25 CN202 87-A60-130-010 CONN,5P V
<YKZD88RDF,ZD8RD> CN501 84-ZG1-647-010 CONN ASSY,2P
C301 87-010-382-080 CAP, ELECT 22-25V <EXCEPT ZD8RN1DM,ZD8RNDM>
C302 87-010-196-020 CHIP CAPACITOR,0.1-25 CN601 87-009-345-010 CONN,2P PH V
<EXCEPT YKZD88RDF,ZD8RD> <EXCEPT ZD8RN1DM,ZD8RDM,YZD8RDM,ZD8RNDM>
C302 87-010-196-080 CHIP CAPACITOR,0.1-25 CON401 87-099-030-010 CONN,13P 6216H
<YKZD88RDF,ZD8RD> FB601 87-008-372-080 FLTR,EMI BL01 RN1
C303 87-010-260-080 CAP, ELECT 47-25V <EXCEPT ZD8RN1DM,ZD8RDM,YZD8RDM,ZD8RNDM>

C401 87-010-322-020 C-CAP,S 100P-50 CH FB602 87-008-372-080 FLTR,EMI BL01 RN1

<EXCEPT YKZD88RDF,ZD8RD> LED601 87-A40-558-010 LED,SLZ-8128A-01-A
C401 87-010-322-080 C-CAP,S 100P-50 CH M201 87-045-305-010 MOTOR, RF-500TB DC-5V (2MA)
<YKZD88RDF,ZD8RD> SW201 87-036-109-010 SW,MICRO SPPB61
C402 87-010-322-020 C-CAP,S 100P-50 CH SW202 87-036-109-010 SW,MICRO SPPB61
<EXCEPT YKZD88RDF,ZD8RD>
C402 87-010-322-080 C-CAP,S 100P-50 CH X101 87-A70-046-010 VIB,XTAL 16.934MHZ
<YKZD88RDF,ZD8RD>
C403 87-010-322-020 C-CAP,S 100P-50 CH
<EXCEPT YKZD88RDF,ZD8RD> LED. C.B

C403 87-010-322-080 C-CAP,S 100P-50 CH LED501 87-A40-263-080 LED,SLH-56PCT31 GRN

<YKZD88RDF,ZD8RD> <EXCEPT ZD8RN1DM,ZD8RNDM>
C404 87-010-322-080 C-CAP,S 100P-50 CH LED502 87-A40-263-080 LED,SLH-56PCT31 GRN
<YKZD88RDF,ZD8RD> <EXCEPT ZD8RN1DM,ZD8RNDM>
C404 87-010-322-020 C-CAP,S 100P-50 CH LED503 87-A40-268-080 LED,SLH-56DCT31 ORN
<EXCEPT YKZD88RDF,ZD8RD> <EXCEPT ZD8RN1DM,ZD8RNDM>
C405 87-010-322-020 C-CAP,S 100P-50 CH LED504 87-A40-268-080 LED,SLH-56DCT31 ORN
<EXCEPT YKZD88RDF,ZD8RD> <EXCEPT ZD8RN1DM,ZD8RNDM>
C405 87-010-322-080 C-CAP,S 100P-50 CH
<YKZD88RDF,ZD8RD>
T-T C.B
C406 87-010-322-020 C-CAP,S 100P-50 CH
<EXCEPT YKZD88RDF,ZD8RD> C401 87-018-214-080 CAP TC U 0.1-50F
C406 87-010-322-080 C-CAP,S 100P-50 CH CON401 86-NFZ-675-010 CONN,5P H 6216-11H
<YKZD88RDF,ZD8RD> M401 87-045-364-010 MOTOR(BCH3B14)
C407 87-010-405-080 CAP, ELECT 10-50V PS401 87-026-573-010 SNSR,PHOTO GP1S53V
C454 87-010-196-020 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD>
C454 87-010-196-080 CHIP CAPACITOR,0.1-25 MOTOR C.B
<YKZD88RDF,ZD8RD>
PIN3 91-564-722-110 CONN,PIN 6P
C601 87-010-260-080 CAP, ELECT 47-25V SW1 91-572-085-110 LEAF SWITCH
C602 87-010-196-080 CHIP CAPACITOR,0.1-25
<YKZD88RDF,ZD8RD>
C602 87-010-196-020 CHIP CAPACITOR,0.1-25
<EXCEPT YKZD88RDF,ZD8RD>
CN1 87-A60-429-010 CONN,16P H TOC-A
CN201 84-ZG1-648-010 CONN ASSY,6P

• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

5
TRANSISTOR ILLUSTRATION

C D

B G
E ECB S
2SA1235F 2SA1980Y/G 2SK2158
2SC3052F KTA1266GR
DTC124XK

6
BLOCK DIAGRAM

LCHO
RCHO
XOUT

XIN

LVSS,
RVSS
RVDD

TDO

PIN3

CON
401

7 8
WIRING
1 2 3 4 5 6 7 8 9 10 11 12 13 14

TO CD C.B
CN201

PIN3
D TO MOTOR C.B PIN3

K
9 10
SCHEMATIC DIAGRAM

IC101
LC78641E

M201
MOVE
3.6V

VDD/2V

11 12
TEST MODE
1. How to Start the CD Test Mode *1 ...... When the focus search keeps running for 10 minutes or longer continuously, the driver IC heats up, and the protective circuit works
so that the machine may stops operating.
While pressing the CD function key, connect the AC power plug to wall outlet. In this case, turn off the main power, wait for a while and restart the machine.
The test mode starts up and “CD TEST” appears on the display.
*2 ...... Do not keep pressing the FF or RWD button while the pickup is located at the innermost or outermost circumference because the
2. How to Exit the CD Test Mode gear can be damaged as the sled motor keeps rotating.
Press the POWER button or disconnect the AC power plug from wall outlet.
* When any function key other than PLAY is pressed during playback, the test mode is canceled.
4. Automatic Adjustment Result Display
3. Function and Use of the CD Test Mode The automatic adjustment values of the focus and the tracking can be displayed.

How to enter the 4-1. Automatic Adjustment Result Display of Focus Offset Cancel/Gain
NO MODE Display Operation Check item
mode 1) Enter the start mode (all indicators turn on).
2) Press the TAPE button to display “F**” and set each of the adjustment item to either ON or OFF. (Refer to the following
1 Start mode All indicators turn • All FL all ndicators turn on • FL check
table.)
on • Microprocessor check 3) Press the PLAY button to play back the CD.
4) Press the CD button.
2 Search mode STOP button CD • LD turns on all the time • APC circuit check
5) The automatic adjustment value “F** **” is displayed. (Refer to the following table.)
• Focus search continuos • Laser current measurement 6) Upon completion of check, press the CD button twice to return to the play mode.
operation *1 • Focus search waveform
Automatic adjustment value display
• Spindle motor continuos check Adjustment item (ON = 1, OFF = 0)
(Asterisk * means hexadecimal display.)
kick • Focus error waveform check
F OFFSET GAIN F OFFSET — GAIN
(Ignores DRF during search
F 0 0 F Not displayed Not displayed Not displayed
mode)
F 1 1 F ** Not displayed **
3 Play mode PLAY button Normal • Normal playback • Each servo circuit is checked
F 1 0 F ** Not displayed Not displayed
• Focus search is continued if • DRF check
F 0 1 F Not displayed Not displayed **
failed in TOC READ.
4 Traverse mode PAUSE button Normal • Tracking servo OFF/ON • Tracking balance check
Repeats OFF/ON every time 4-2. Automatic Adjustment Result Display of Tracking Offset Cancel/Balance/Gain
the PAUSE button is 1) Enter the start mode (all indicators turn on).
2) Press the AUX button to display “T***” and set each adjustment item to either ON or OFF. (Refer to the following table.)
pressed 3) Press the PLAY button to play back the CD.
5 Sled mode FF button CD TEST • Moves PU to inner • Sled circuit check 4) Press the CD button twice.
5) The automatic adjustment value “F******” is displayed. (Refer to the following table.)
circumference *2 • Tracking circuit check 6) Upon completion of check, press the CD button to return to the play mode.
Kicks the lens to inner • Mechanism operation check
circumference at the same • PU check Automatic adjustment value display
Adjustment item (ON = 1, OFF = 0)
time (Asterisk * means hexadecimal display.)

RWD button CD TEST • Moves PU to outer T OFFSET BALANCE GAIN T OFFSET BALANCE GAIN

circumference *2 T 0 0 0 T Not displayed Not displayed Not displayed

Kicks the lens to outer T 1 1 1 T ** ** **

circumference at the same T 1 1 0 T ** ** Not displayed

time T 1 0 1 T ** Not displayed **

6 Spindle mode TAPE REC All indicators turn • Pressing the button once • Spindle circuit check T 1 0 0 T ** Not displayed Not displayed

button on rotates the spindle motor in • Spindle motor check T 0 1 1 T Not displayed ** **

the normal direction (rough T 0 1 0 T Not displayed ** Not displayed

speed). Pressing the button T 0 0 1 T Not displayed Not displayed **

again rotates it in the reverse

direction. Pressing it again
stops the motor
7 RF AGC mode TUNER button AGC ON/OFF • Repeats ON/OFF every time • PU good or defective check
the TUNER button is • RF AMP circuit check
pressed

13 14
WAVE FORM IC BLOCK DIAGRAM
IC, BA5927S
1 IC201 • (IN6-R) VOLT/DIV: 500mV
TIME/DIV: 200mS
2 IC201 ª (IN6-F)

1.6Vp-p

1
2

1.6Vp-p

3 Between CN202 1 and 2 VOLT/DIV: 1V

(2 Pin: 0 Level) TIME/DIV: 200mS

4 IC101 % (FE) VOLT/DIV: 500mV

TIME/DIV: 2mS

IC, LA9235M
1.75Vp-p

5 IC101 ^ (TE) VOLT/DIV: 200mV

TIME/DIV: 200µS

1.0Vp-p

15 16
IC DESCRIPTION
IC, LC78641E
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 PDO1 O Internal VCO control phase comparator output pin. (Pull down) 39 EFLG O C1, C2 error correction monitor pin. (Not connected)
Internal VCO control phase comparator output pin. 40 TEST I Test input pin. (Connected to GND)
2 PDO2 O
OFF for rough servo, ON for phase servo. (Pull down) Emphasis pin. Which becomes an input pin after reset and can be controlled externally.
41 EMPH I/O
3 VVSS — Internal VCO ground pin. This becomes an emphasis monitor pin under control by command. (Not connected)
4 PCKIST — PDO output current adjustment resistor connection pin. 42 MUTEL O L channel mute output pin. (Not connected)
5 VVDD — Internal VCO power supply pin. 43 MUTER O R channel mute output pin. (Not connected)
6 FR — VCO frequency range adjustment resistor connection pin. (Pull up) 44 LVDD — L channel power supply pin.
7 HFL I Mirror detection signal input pin. 45 LCHO O L channel output pin.
8 SLCIST — SLCO output current adjustment resistor connection pin. 46 LVSS — L channel ground pin.
9 SLCO O Control output. 47 RVSS — R channel ground pin.
10 EFMIN I EFM signal input pin. 48 RCHO O R channel output pin.
11 JITTV O Jitter detection monitor pin. 49 RVDD — R channel power supply pin.
12 JITTC O Jitter detection adjustment pin. (Pull down) 50 XVDD — Crystal oscillator power supply pin.
13 BH I BH signal input pin. (Connected to GND) 51 XIN I
Connections for a 16.9344MHz crystal oscillator pin.
14 PH (RFENV) I PH signal or RFENV signal input pin. 52 XOUT O
15 FE I FE signal input pin. 53 XVSS — Crystal oscillator ground pin.
16 TE I TE signal input pin. 54 ASLRCK I L/R clock input pin. (Connected to GND)
17 VREF I VREF input pin. 55 ASDACK I Bit clock input pin. (Connected to GND)
18 ADAVDD — Servo A/D, D/A power supply pin. 56 ASDFIN I L/R channel data input pin. (Connected to GND)
19 ADAVSS — Servo A/D, D/A ground pin. 57 LRSY O L/R clock output pin. (Not connected)
20 PHREF O PH reference output pin. (Not connected) 58 DATACK O Bit clock output pin. (Not connected)
21 BHREF O BH reference output pin. (Not connected) 59 DATA O L/R channel data output pin. (Not connected)
22 TBLO O Tracking balance output pin. 60 16M O 16.9344MHz output pin. (Not connected)
23 TDO O Tracking control output pin. Subcode frame synchronization signal output pin. This signal falls when the subcode is
61 SFSY O
24 FDO O Focus control output pin. in the standby state. (Not connected)
25 SPDO O Spindle control output pin. 62 SBSY O Subcode clock synchronization signal output pin. (Not connected)
26 SLDO O Thread control output pin. 63 PW O Subcode P, Q, R, S, T, U and W output pin. (Not connected)
27 DVREF/FG I/O Output driver VREF output pin. FG signal input pin. (Connected to GND) 64 SBCK I Subcode readout clock input pin. (Connected to GND)
28 LASER O Laser ON/OFF control pin. 65 CE I Chip enable signal input pin.
29 CONT1 I/O General-purpose input/output pin 1. (Connected to GND) 66 CL I Data transfer clock input pin.
30 CONT2 I/O General-purpose input/output pin 2. (Connected to GND) 67 DI I Data input pin.
31 CONT3 I/O General-purpose input/output pin 3. (Connected to GND) 68 DO O Data output pin.
32 CONT4 I/O General-purpose input/output pin 4. 69 INT O Interruption signal output pin. (Not connected)
33 CONT5 I/O General-purpose input/output pin 5. (Not connected) 70 WRQ O Interruption signal output pin.
EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. 71 RES I Reset input pin. This pin must be set low briefly after power is first applied.
34 PCK O
(Not connected) 72 DRF O Focus ON detect pin.
35 C2F O C2 flag output pin. (Not connected) 73 VDD5V — Microprocessor interface power supply.
36 VDD — Digital power supply pin. 74 VSS — Digital ground pin.
37 DOUT O Digital out output pin. (EIAJ format) 75 CONT6 I/O General-purpose input/output pin 6.
Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. 76 CONT7 I/O General-purpose input/output pin 7.
38 FSX O
(Not connected) Rough servo/phase control automatic switching monitor output pin.
77 V/P O
“H” for rough servo and “L” for phase servo. (Not connected)

17 18
Pin No. Pin Name I/O Description
Synchronization signal detection output pin.
78 FSEQ O Outputs a high level when the synchronization signal detected from the EFM signal
and the internally generated synchronization signal agree. (Not connected)
Defect pin. Which becomes an input pin after reset and can be controlled externally.
79 DEFECT I/O
This becomes the defect monitor pin under control by command. (Not connected)
80 EFMO O EFM signal output pin. (Not connected)

19
MECHANICAL EXPLODED VIEW 1/1

28 29
30 A

14 27

26
13
31
25
19
24 20

P.C.B
23
21
12 22

C
11

B a

10
a
32

4
8
18
7
6 P.C.B
17

3 5
4

P.C.B
CUSHION,CD880
1 16

15 15
33
CUSHION,CD880

20
MECHANICAL PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 84-ZG1-225-010 BELT,SQ1.0-63.3 20 81-ZG1-255-110 PLATE,MAGNET MK2<EXCEPT ZD8RN1DM>
2 84-ZG1-673-010 F-CABLE,5P 1.25 210MM BLACK N 21 83-ZG3-604-010 RING,MAG 2
<EXCEPT ZD8RN1DM,ZD8RNDM> 22 83-ZG3-213-010 LVR,SW
2 84-ZG1-672-010 F-CABLE,5P 1.25 210MM WHITE N 23 84-ZG1-208-210 LEVER,CAM<YKZD8RDF>
<ZD8RN1DM,ZD8RNDM> 23 84-ZG1-266-010 LEVER,CAN 8<EXCEPT YKZD8RDF>
3 87-045-364-010 MOTOR(BCH3B14)
4 84-ZG1-267-010 PULLEY,LOAD MO 8 24 84-ZG1-205-210 GEAR,TRAY (*)
<EXCEPT YKZD8RDF,ZD8RD> 25 81-ZG1-291-110 GEAR,TRAY RELAY NO3
26 84-ZG1-206-110 GEAR,RELAY<YKZD8RDF>
4 81-ZG1-212-010 PULLY,LOAD MO<YKZD8RDF,ZD8RD> 26 84-ZG1-274-010 GEAR,RELAY 8<EXCEPT YKZD8RDF>
5 84-ZG1-238-010 GEAR,WORM N 27 84-ZG1-207-010 PULLEY,RELAY
6 84-ZG1-248-010 SPR-C,WORM
7 84-ZG1-239-210 PULLY,WORM N 28 84-ZG1-209-010 BELT,SQ1.8-117.7
8 84-ZG1-008-210 TRAY,NO3<ZD8RD> 29 84-ZG1-203-410 GEAR,MAIN CAM<ZD8RNDM>
29 84-ZG1-215-410 GEAR,MAIN CAM BLU<EXCEPT ZD8RNDM>
8 8A-ZG1-001-010 TRAY,NO3 BLU<EXCEPT ZD8RD> 30 84-ZG1-011-010 REFLECTOR,CD
9 8A-ZG1-210-010 HLDR,MAGNET 23<YKZD8RDF> <EXCEPT ZD8RN1DM,ZD8RNDM>
9 84-ZG1-243-210 HLDR,MAGNET N(J) 31 84-ZG1-216-310 SLIDE,MECHA CAM YEL
<YZD8RDJM,ZD8RMDJM,YZD8RMDJM> <EXCEPT ZD8RNDM>
9 84-ZG1-289-010 HLDR,MAGNET NAT<ZD8RNDM>
9 81-ZG1-277-310 HLDR,MAGNET N 31 84-ZG1-204-310 SLIDER,MECHA CAM<ZD8RNDM>
<ZD8RN1DM,ZD8RDM,YZD8RDM,ZD8RD> 32 84-ZG1-286-010 CHAS,MECHA NAT<ZD8RNDM>
32 84-ZG1-201-410 CHAS,MECHA<EXCEPT ZD8RNDM>
10 84-ZG1-259-010 SPR-P,WORM 33 M8-ZZK-C90-070 KSM-880CAB
11 84-ZG1-221-010 GEAR,MAIN TT<YKZD8RDF> A 87-067-703-010 TAPPING SCREW, BVT2+3-10
11 84-ZG1-269-010 GEAR,MAIN TT 4<EXCEPT YKZD8RDF> <EXCEPT ZD8RN1DM,ZD8RNDM>
12 84-ZG1-224-010 LEVER,TT<EXCEPT ZD8RNDM>
12 84-ZG1-288-010 LEVER,TT NAT<ZD8RNDM> B 87-067-981-010 BVT2+3-6 BLK
C 87-251-070-410 U+2.6-3
13 8A-ZG1-002-010 TURN TABLE,NO1 BLU<EXCEPT ZD8RD>
13 84-ZG1-005-210 TURNTABLE,NO1(*)<ZD8RD>
14 81-ZG1-239-010 S-SCREW,TT
15 8A-ZG1-201-010 S-SCREW,MECH 880
16 85-NFT-611-110 FF-CABLE 16P-1.0

17 84-ZG1-299-210 HLDR,MECHA NO3<EXCEPT ZD8RNDM>

17 8A-ZG1-203-010 HLDR,MECHA NO3 NAT<ZD8RNDM>
18 87-045-305-010 MOTOR, RF-500TB DC-5V (2MA)
19 84-ZG1-211-010 SPR-E CAM S
20 84-ZG1-285-010 PLATE,MAGNET BLK<ZD8RN1DM>

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange

21
CD MECHANISM EXPLODED VIEW 1/1

6
7
4 5

A 9

10

11

2
3

P.C.B
1

CD MECHANISM PARTS LIST 1/1

REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 91-564-722-110 CONN,PIN 6P 8 92-647-742-010 SPRING COMPRESSION
2 91-572-085-110 LEAF SWITCH 9 93-321-813-110 POLI WASHER
3 9X-264-655-010 SL MOTORR ASSY 10 92-647-407-010 GEAR A
4 M8-ZZK-C90-070 KSM-880CAB 11 92-647-408-020 GEAR B
5 92-647-416-020 SPRING EXTENSION A 93-713-786-510 SCREW,+P2-3

6 92-647-595-020 SHUTTER B
7 92-647-732-010 NS SLIDE RACK

22
REFERENCE NAME LIST
ELECTRICAL SECTION MECHANICAL SECTION
DESCRIPTION REFERENCE NAME DESCRIPTION REFERENCE NAME

ANT ANTENNAS ADHESHIVE SHEET ADHESHIVE

C- CHIP AZ AZIMUTH
C-CAP CAP, CHIP BAR-ANT BAR-ANTENNA
C-CAP TN CAP, CHIP TANTALUM BAT BATTERY
C-COIL COIL, CHIP BATT BATTERY

C-DI DIODE, CHIP BRG BEARING

C-DIODE DIODE, CHIP BTN BUTTON
C-FET FET, CHIP CAB CABINET
C-FOTR FILTER, CHIP CASS CASSETTE
C-JACK JACK, CHIP CHAS CHASSIS

C-LED LED, CHIP CLR COLLAR

C-RES RES, CHIP CONT CONTROL
C-SFR SFR, CHIP CRSR CURSOR
C-SLIDE SW SLIDE SWITCH, CHIP CU CUSHION
C-SW SWITCH, CHIP CUSH CUSHION

C-TR TRANSISTOR, CHIP DIR DIRECTION

C-VR VOLUME, CHIP DUBB DUBBING
C-ZENER ZENER, CHIP FL FRONT LOADING
CAP, CER CAP, CERA-SOL FLY-WHL FLYWHEEL
CAP, E CAP, ELECT FR FRONT

CAP, M/F CAP, FILM FUN FUNCTION

CAP, TC CAP, CERA-SOL G-CU G-CUSHION
CAP, TC-U CAP, CERA-SOL SS HDL HANDOL
CAP, TN CAP, TANTALUM HIMERON CLOTH
CERA FIL FILTER, CERAMIC HINGE, BAT HINGE, BATTERY

CF FILTER, CERAMIC HLDR HOLDER

DL DELAY LINE HT-SINK HEAT SINK
E/CAP CAP, ELECT IB INSTRUCTION BOOKLET
FILT FILTER IDLE IDLER
FLTR FILTER IND, L-R INDICATOR, L-R

FUSE RES RES, FUSE KEY, CONT KEY, CONTROL

MOT MOTOR KEY, PRGM KEY, PROGRAM
P-DIODE PHOTO DIODE KNOB, SL KNOB, SLIDE
P-SNSR PHOTO SENSER LBL LABEL
P-TR PHOTO TRANSISTOR LID, BATT LID, BATTERY

POLY VARI VARIABLE CAPACITOR LID, CASS LID, CASSETTE

PPCAP CAP, PP LVR LEVER
PT POWER TRANSFORMER P-SP P-SPRING
PTR, RES PTR, MELF PANEL, CONT PANEL, CONTROL
RC REMOTE CONTROLLER PANEL, FR PANEL, FRONT

RES NF RES, NON-FLAMMABLE PRGM PROGRAM

RESO RESONATOR PULLY, LOAD MO PULLY, LOAD MOTOR
SHLD SHIELD RBN RIBBON
SOL SOLENOID S- SPECIAL
SPKR SPEAKER SEG SEGMENT

SW, LVR SWITCH, LEVER SH SHEET

SW, RTRY SWITCH, ROTARY SHLD-SH SHIELD-SHEET
SW, SL SWITCH, SLIDE SL SLIDE
TC CAP CAP, CERA-SOL SP SPRING
THMS THERMISTOR SP-SCREW SPECIAL-SCREW

TR TRANSISTOR SPACER, BAT SPACER, BATTERY

TRIMMER CAP, TRIMMER SPR SPRING
TUN-CAP VARIABLE CAPACITOR SPR-P P-SPRING
VIB, CER RESONATOR, CERAMIC SPR-PC-PUSH P-SPRING, C-PUSH
VIB, XTAL RESONATOR, CRYSTAL T-SP T-SPRING

VR VOLUME TERM TERMINAL

ZENER DIODE, ZENER TRIG TRIGGER
TUN TUNING
VOL VOLUME
W WASHER

WHL WHEEL
WORM-WHL WORM-WHEEL

23
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
0251431 Printed in Singapore