Controller Introduction

Desk Assembly Instruction

S Short press the button,the display flashes,Press any of memory key to save the height.

Memory button: Press the 1 2 3 button and the desk will move to the height that was previously set for the button.

Press the button to raise the desk. Releasing the button stops the process. The maximum height of the desk is 118 cm.

Press the button to lower the desk. Releasing the button stops the process. The minimum height of mthe desk is 72 cm.

Press and hold the button for 5 seconds, and the screen will show'RES.'
Reset
Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Overheat protection: When the motor operates continuously,it will stop running to prevent damage caused by
Hot
overhe ating. Wait for a period of time (15-20minutes) before making any further height adjustments.

Sensor malfunction warning: Motor safety sensor cannot be detected. Please power off, unplug the cables of the controller,
E10
wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.

Overloading Warning: Over the max of loading weight. Power off, take the things off the desk, power back on, and try
E20
again.

Operation Status Warning: The desk stops moving if vibration, impact, or incline is detected. If this detection is incorrect,
E02
follow the reset instructions before continuing use.

Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, please power off, unplug the cables
E32
of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.

E31
Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, please power off, unplug the cables
of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
Gaming Table - Agr Lite Frame
Unequal Leg Height Waming: Check whether all the legs are at the same height. If necessary, adjust it by following the
E60 reset instructions.

Cable Disconnection Warning: Please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the
-
cables and connect the power again, and perform RES settings again.

RATED

Engineering Mode
Power Input Speed Motion Noise Load Capability
ChangeDisplayed Long press the S button, “S--”shows and flashes. Press S again and the display shows “Un”. 100V-240V 20 mm/s ＜55dB 154 lbs / 70 kg
Press S to select. Press or to switch between“ ”(metric) or “ ” (imperial).
Unit( Un ) Press S to save your choice.
Long press the S button, “S--”shows and flashes. Press S again and the display shows “Un”.
CollisionForce Press or to switch to“CF”. Press S to select. Press or to switch between“OFF”,Low(L),
Detection( CF ) Normal (n) or Heavy (H) collision force detection. Press S to save your choice.
COMPONENT LIST Step 5
B M5×15mm(x4)

Headphone
H hanger (x2)

B
H

Step 6
G Cable Clip (x2)

Right Table Leg (x1) Left Table Leg (x1) Leg Base (x2)

Transmission rod (x1) Controller (x1) Power (x1) 2

1

Side Plate (x2) Connector (x1) Left Crossbar (x1) 1 2

G
Right Crossbar (x1)

01 06
Step 4 HARDWARE LIST
D M6×12mm(x4)
Note: The tabletop not included.
F S=5mm
A B C

S=5mm Screws Screws Screws

M6×8mm (x8) M5×15mm (x16) M6×35mm (x8)

D D E F

Screws Allen Key Allen Key

M6×12mm (x4) S=2mm (x1) S=5mm (x1)

G H

Cable Clip (x2) Headphone hanger (x2)

B M5×15mm(x12)

1 Spare Parts
B

A B C D
M6×8mm (x2) M5×15mm (x2) M6×35mm (x1) M6×12mm (x1)

B 2

05 02
Step 1 Step 2
A M6×8mm(x4)

F S=5mm

S=5mm

Please note the direction.

A M6×8mm(x4)

F S=5mm

Step 3 1
A

S=5mm 2

C M6×35mm(x8)

3
F S=5mm

S=5mm

K
E

C
4

E S=2mm

03 04