Scribd
Upload
44 views3 pages

Model Question - EHV LAB As 6.11.2024

Uploaded by

sabarijvss02
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
44 views3 pages

Model Question - EHV LAB As 6.11.2024

Uploaded by

sabarijvss02
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Title of Practical Course : ELECTRIC AND HYBRID VEHICLE LAB

Practical Course Code : U20EEP716


Year / Semester : IV /VII
Batch / Regulation : 2021 – 2025 / R2020
Date of the Practical Exam : 6.11.2024

B.Tech Model Practical Examination/Nov – 2024

Questions

1. A) Demonstrate the hall effect sensor wire, tail head lamp wire, throttle switch wire
and brake wire from BLDC controller board.
(2)
B) Conduct the suitable experiment to determine speed of Hub motor 250W for
different throttle voltage and obtain the graph from Digital oscilloscope for different
mode. (2)

2. Simulate and examine the power rating requirement Electric motor for electric
vehicle for grading slope of ___ degree and ___ degree by simulation and analysis
its transient and steady condition. Obtain the waveform for vehicle velocity, steady
state and dynamic state power requirement from time 0 to 100 sec
(3)

3. Simulate and examine the power rating requirement of Electric motor for electric
vehicle for grading slope of ___ degree and ___ degree by simulation and analysis
its transient and steady condition. Obtain the waveform for vehicle acceleration and
velocity in m/s, rolling resistance power, grading power, and aerodynamic power
from time 0 to 150 sec (3)

4. Design the battery rating for Electric Vehicle to operate a)60 KM, b)100 KM range
and do the simulation (3)

5. Do the simulation to find the power rating of Electric motor for hybrid electric
vehicle for grading slope of 2 o degree and 4o degree by simulation and analysis its
transient and steady condition. Obtain the waveform corresponding to said grading
slope.
(4)
6. Compare and analysis the power requirement of all mode condition of hybrid
electric vehicle. Obtain the waveform and bar chart by comparing - mode1, mode2,
mode3.

(4)
7. Simulate and analysis the steady state force, dynamic force, power train tractive
effort, vehicle acceleration, IC engine power requirement, sizing of motor for
electric vehicles for hybrid electric vehicle. Compare the mode-1, mode-2, and
mode-3 power and torque requirement
(4)

8. Conduct a suitable experiment for speed control of BLDC Motor 750W and obtain
its current waveform by suitable probe
(5)

9. Simulate and analysis the speed performance of SRM Motor for electric bike by
implementing suitable controller system for 6/4 configuration. (6)

10. A) Conduct a suitable experiment for the Hall Effect sensor Position Detect and
Velocity Meter Circuit for motor operation. (7)
B) Conduct a suitable experiment for the Light Detection and Ranging (Lidar)
sensors used in electric vehicles.
(7)

11. Conduct a suitable experiment to demonstrate the closed loop performance of speed
control of BLDC motor 350W and obtain its voltage waveform by through proper
isolation transformer
(8)
12. a) Design the firing circuit and power module for BLDC controller 250W motor.
b) Conduct a suitable experiment to demonstrate the open loop performance of
speed control of BLDC motor
(8)

13. Design the Battery Charger Circuit for Lead Acid Battery with a rating of 45Ah.
Calculate charging time and battery life in hours. (9)
14. Design the Battery Charger Circuit for Lead Acid Battery with a rating of 120Ah.
Calculate charging time and battery life in hours. (9)
15. Design the Lithium ion Battery Charger Circuit for 4 no. of cells for 3.7V Lithium
ion batteries with a rating in the range of 1.2Ah to 2Ah. (10)
16. Design the Lithium ion Battery Charger Circuit for 6 no. of cells for 3.7V Lithium
ion batteries with a rating in the range of 1.2Ah to 2Ah. (10)
17. Design a battery charger circuit by LM 2576 IC for 12 V battery
(10)
18. Design a battery charger circuit by LM 2576 IC for 24 V battery
(10)

You might also like