TFT MODULE SPECIFICATION

RVT50HQSNWC00-B
STM32 EMBEDDED 5.0" DISPLAY DATASHEET

Rev.1.1
2024-07-12

ITEM CONTENTS UNIT

LCD Type TFT/Transmissive/Normally Black/IPS /
Size 5.0 Inch
Viewing Direction Free /
Outside Dimensions (W x H x D) 136.00 x 92.80 x 12.05 mm
Active Area (W x H) 108.00 x 64.80 mm
Pixel Pitch (W x H) 0.135 x 0.135 mm
Resolution 800 x 480 /
Brightness 850 cd/m2
Color Depth 16.7 M /
Pixel Arrangement RGB Vertical Stripe /
STM32U5A9NJH6Q
Micro Controller Unit /
4MB Flash, 2.5MB RAM
External Flash Memory 512Mbit /
Supply Voltage for Module 6.0 - 48.0 V
With/Without Touch With Projected Capacitive Touch Panel /
CTP Driver ILI2132A /
Bonding Technology Optical Bonding /
Weight 146 g

Note 1. RoHS3 compliant

Note 2. LCM weight tolerance: ± 5%.

RVT50HQSNWC00-B

REVISION RECORD
REV NO. REV DATE CONTENTS REMARKS

1.0 2023-05-24 Initial version

Updated the PCB laminate to 1.1, for

1.1 2024-07-12
details refer to changelog.

© 2024 Riverdi Page 2 of 17 www.riverdi.com

RVT50HQSNWC00-B

CONTENTS
REVISION RECORD ................................................................................................................................... 2
CONTENTS ...................................................................................................................................................... 3
MODULE CLASSIFICATION INFORMATION ............................................................................... 4
uxTouch ASSEMBLY GUIDE ................................................................................................................. 5
MODULE DRAWING ................................................................................................................................. 6
ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 7
ELECTRICAL CHARACTERISTICS ...................................................................................................... 7
BACKLIGHT ELECTRICAL CHARACTERISTICS .......................................................................... 8
ELECTRO-OPTICAL CHARACTERISTICS ....................................................................................... 8
BOARD INTERFACES AND CONNECTORS ............................................................................... 10

USER INTERFACES .................................................................................................................................. 14

DISPLAY SEPCIFICATION .................................................................................................................... 16

RELIABILITY TEST ..................................................................................................................................... 16

LEGAL INFORMATION ........................................................................................................................... 17

© 2024 Riverdi Page 3 of 17 www.riverdi.com

RVT50HQSNWC00-B

MODULE CLASSIFICATION INFORMATION

RV T 50 H Q S N W C 00 B
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.

NO. PARAMETER SYMBOL

1. BRAND RV – Riverdi
2. PRODUCT TYPE T – TFT Standard
3. DISPLAY SIZE 50 – 5.0”
4. MODEL SERIAL NO. H – High Brightness, IPS TFT
5. RESOLUTION Q – 800x480 px

S –STM32 Embedded Display

6. LCD+CONTROL BOARD
MCU STM32U5A9NJH6Q

7. FRAME N – Without Mounting Metal Frame

8. BACKLIGHT TYPE W – LED White
9. TOUCH PANEL C – With Capacitive Touch Panel
10. VERSION 00 – (00-99)
BONDING
11. B – Optical bonding
TECHNOLOGY

© 2024 Riverdi Page 4 of 17 www.riverdi.com

RVT50HQSNWC00-B

uxTouch ASSEMBLY GUIDE

uxTouch are LCD TFT displays with specially designed projected capacitive touch panels.
uxTouch display can be mounted without any additional holes in the housing. Our standard
uxTouch displays include double-sided adhesive tape (DST) to stick TFT easily to the
housing.
uxTouch models with double-side adhesive tape can be mounted by fastening the glass to
the housing.

Figure 1. General view of the module

© 2024 Riverdi Page 5 of 17 www.riverdi.com

 Revision: Changes: Date:
1.0 Initial Case 2023.05.24

1.1 PCB Update - 50STM32U5_Rev1.1 2024.07.12

136.00 [5.354](CG O.D.)

120.30 [4.736](TFT O.D.) 7.87 [0.310]
119.90 [4.720](SENSOR O.D.) 8.07 [0.318] MAX 12.05 [0.475](MODULE O.D.)
10.94 [0.431]
11.14 [0.439]
13.00 [0.512]
13.70 [0.539]
14.00 [0.551]

110.00 [4.331](SENSOR A.A.) 13.00 [0.512] 4.73 [0.186](CTP+TFT) DOUBLE-SIDED TAPE

108.60 [4.276](CG V.A.) 13.70 [0.539] 2.03 [0.080](CG+SCA+SENSOR+OCA) 3M9495 T=0.175mm[0.007inch]
108.00 [4.252](TFT A.A.) 14.00 [0.551] 1.275 [0.050](CG+DST) 41.06±0.5 [1.616±0.020]
97]
68.00 [2.677]
[ R 0.1 1.10 [0.043](CG) 0.68±0.5 [0.027±0.020]
0
5.0 46.28 [1.822] 64.70 [2.547]
4*R

A S3 S1 USER BTN
J1 P6
USER LED

USB OVR
50.23±0.5 [1.977±0.020]
PWR LED
46.40 [1.827]

P7 P5 USB

RS485
4 1 4 1 5 1

2
1
CANFD
74.80 [2.945](SENSOR O.D.)

39.36 [1.550]
S2

68.36 [2.692]
66.80 [2.630](SENSOR A.A.)

0.00±0.5 [0.000±0.020]
64.80 [2.551](TFT A.A.)
92.80 [3.654](CG O.D.)

65.40 [2.575](CG V.A.)

RESET
75.40 [2.969](TFT O.D.)

P3 SWD
LENS 10 1

5.88 [0.232]
P1

(T=1.1mm[0.043inch]) BT1 6 1
40 1
SCA

BOOT
P2

(T=0.2mm[0.008inch]) P4

40
39
5.0" RGB DISPLAY
CN1

POWER
SENSOR 4 1

(T=0.55mm[0.022inch])
P10

20

6
P9
OCA AREA
COMPONENT
(T=0.175mm[0.007inch])

1
1
BLVDD INT

BLVDD EXT
Component Area

4 1

BATTERY HOLDER
(CR1220)
EXPANSION CONNECTOR
DETAIL A 39.45 [1.553] 1.27mm
BLACK MASK PRINTING SCALE 4:1 3*M3*4mm 2x20PIN SOCKET
RAL9005 THREADED SPACER RIBUS, 20PINS, 0.5mm PITCH
0.20 [0.008]*45° DOWNSIDE CONTACT, FLIP
LEDA LEDK
BACKLIGHT VOLTAGE SETUP
0.20 [0.008]*45°

1.25 MM MOLEX CONNECTORS LED Circuit Diagram

NO. TYPE MATE WITH

P3 (SWD) 53261-0671 51021-0600
P5 (CAN) 53261-0471 51021-0400
1.27MM PIN SOCKET
P6 (USB) 53261-0571 51021-0500
P7 (RS485) 53261-0471 51021-0400 NO. TYPE MATE WITH
P10 (POWER) 53261-0671 51021-0600 P4 CBC1402M100-2P CH51402M100-0P OR CH51402V100
TFT NOTES: TP NOTES: GENERAL NOTES:
1. DISPLAY TYPE: TRANSMISSIVE, NORMALLY BLACK, IPS 1. TP STRUCTURE: G+G 1. OPTICAL BONDING
2. RESOLUTION: 800x480 2. CG THICKNESS: 1.10mm[0.043inch] 2. OPERATING TEMPERATURE: -20°C ~ 70°C PN: RVT50HQSNWC00-B
3. VIEWING ANGLE: FREE 3. SURFACE HARDNESS: 7H 3. STORAGE TEMPERATURE: -30°C ~ 80°C
4. SURFACE LUMINANCE: 850 cd/m^2 4. DRIVER IC: ILI2132A 4. WITHOUT INDIVIDUAL TOLERANCE: SN:
5. MCU ON THE BOARD: STM32U5A9NJH6Q 5. INTERFACE: CONNECTED TO MCU VIA I2C ±0.3mm[0.012inch]
6. EXTERNAL FLASH MEMORY SIZE:512Mbit 5. TOLERANCE OF PCB PLACEMENT:
DRAWN: M.Natywa 2024.07.12 1:1.19
7. SUPPLY VOLTAGE FOR MODULE: 6.0V - 48.0V ±0.5mm[0.020inch] CHECKED: M.Wierzbowski 2024.07.12 [mm]
6. RoHS3 COMPLIANT
APPR: T.Soldat 2024.07.12 ISO A3 P. 1 of 1
 RVT50HQSNWC00-B

ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL MIN MAX UNIT NOTE

Supply Voltage for Module VDD_IN 0.0 60.0 Note 1
V
Digital I/O signals Voltage - -0.5 3.3 Note 1,2

Operating Temperature TOP -20 70 °C

Storage Temperature TST -30 80 °C
Storage Humidity (@ 25 ± 5°C) HST 10 - % RH
Operating Ambient Humidity (@ 25 ± 5°C) HOP 10 - % RH
Note 1. Exceeding maximum values may cause improper operation or permanent damage
to the unit.
Note 2. Most of the GPIOs have the 5.0 V tolerant input voltage, please refer to the datasheet
of MCU for more details.

ELECTRICAL CHARACTERISTICS

PARAMETER SYMBOL MIN TYP MAX UNIT

Supply Voltage for Module VDD_IN 6.0 12.0 48.0 V
Power Enable Voltage VEN 0 - VDD_IN V
Input Voltage “H” Level VIH 2.0 - 3.3 V
Input Voltage “L” Level VIL 0 - 0.8 V

PARAMETER CONDITION SYMBOL 1%BL 50% 100% UNIT

BL BL
Current Drawn from VDD_IN @6.0V 60
Current Drawn from VDD_IN @12.0V 149
POWER
Current Drawn from VDD_IN @24.0V IVDD_IN 388 uA
‘ENABLE’ = ‘0’
Current Drawn from VDD_IN @36.0V 630
Current Drawn from VDD_IN @48.0V 872
Current Drawn from VDD_IN @6.0V 136 284 437
Current Drawn from VDD_IN @12.0V 67 141 219
IVDD_IN mA
Current Drawn from VDD_IN @24.0V POWER 35 72 114
Current Drawn from VDD_IN @36.0V ‘ENABLE’ = ‘1’ 24 50 79
Current Drawn from VDD_IN @48.0V 19 40 61
Note 1. POWER ‘ENABLE’ refers to pin 4, ‘ENABLE’ of the power input connector(P10).
POWER ‘ENABLE’ = ‘1’ is when EN pin is floating or shorted to VDD_IN.
POWER ‘ENABLE’ = ‘0’ is when EN pin is shorted to GND.
By default, POWER ‘ENABLE’ is set to ”1”.
Note 2. Test condition: Ambient temp 25 °C PCAP is on Active mode.

© 2024 Riverdi Page 7 of 17 www.riverdi.com

 RVT50HQSNWC00-B

BACKLIGHT ELECTRICAL CHARACTERISTICS

PARAMETER SYMBOL MIN TYP MAX UNIT NOTE

Lifetime - - 50,000 - hours Note 1
Note 1. Operating life means the period in which the LED brightness goes down to 50% of
the initial brightness. Typical operating lifetime is the estimated parameter.

ELECTRO-OPTICAL CHARACTERISTICS

ITEM SYMBOL CONDITION MIN TYP MAX UNIT RMK NOTE

Response Time Tr+Tf - 30 - ms FIG 2. 4
Contrast Ratio Cr 800 1000 - --- 1
θ=0°
Luminance δ
∅=0° - 75 - % 3
Uniformity WHITE FIG 3.
Ta=25 °C
Surface
Lv - 850 - cd/m2 2
Luminance
∅ = 90° - 80 -
Viewing Angle ∅ = 270° - 80 -
θ deg FIG 4. 6
Range ∅ = 0° - 80 -
∅ = 180° - 80 -
Rx 0.575 0.615 0.655 -
Ry 0.296 0.336 0.376 -
Gx 0.352 0.392 0.432 -
θ=0°
CIE (x, y) Gy 0.512 0.552 0.592 -
∅=0° FIG 3. 5
Chromaticity Bx 0.100 0.140 0.180 -
Ta=25 °C
By 0.085 0.125 0.165 -
Wx 0.274 0.316 0.358 -
Wy 0.294 0.336 0.378 -
Note 1. Contrast Ratio (CR) is defined mathematically as below, for more information see
Figure 3.

Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Contrast Ratio =
Average Surface Luminance with all black pixels (P1, P2, P3, P4, P5)

Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying
white. For more information see Figure 3.

Lv = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

Note 3. The uniformity in surface luminance δ WHITE is determined by measuring

luminance at each test position 1 through 5, and then dividing the minimum luminance of
5 points luminance by maximum luminance of 5 points luminance. For more information
see Figure 3.

Minimum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
δ WHITE =
Maximum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

Note 4. Response time is the time required for the display to transition from white to black
(Rise Time, Tr) and from black to white (Decay Time, Tf). For additional information see
Figure 2. The test equipment is BM-7A.

© 2024 Riverdi Page 8 of 17 www.riverdi.com

RVT50HQSNWC00-B

Note 5. CIE (x, y) chromaticity, the x, y value is determined by measuring luminance at each
test position 1 through 5, and then calculating the average value.

Note 6. For TFT module the contrast ratio is greater than 10. The angles are determined for
the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to
LCD surface. For more information see Figure 4.

Note 7. Viewing angle is measured at the center point of the LCD by CONOSCOPE (ergo-
80). For response time testing, the testing data is based on BM-7A. Instruments for Contrast
Ratio, Surface Luminance, Luminance Uniformity, Chromaticity the test data is based on
SR-3A.

Figure 2. The definition of response time

A: 5mm

B: 5mm

H, V: Active Area

Light spot size ∅=5mm, 500mm distance

from the LCD surface to detector lens.

Measurement instrument is TOPCON’S

luminance meter BM-5

Figure 3. Measuring method for Contrast ratio, surface luminance, Luminance uniformity,
CIE (x, y) chromaticity

Figure 4. The definition of viewing angle

© 2024 Riverdi Page 9 of 17 www.riverdi.com

RVT50HQSNWC00-B

BOARD INTERFACES AND CONNECTORS

Power input connector

The 1.25mm, 6-pin Molex connector labeled as “POWER’ (P10) is power input connector.

There is an internal reverse polarity protection which ensures that the device is not
damaged if the power supply polarity is reversed.

NO. PIN DESCRIPTION NOTE

1 VDD_IN Power supply input; 6.0-48.0V
2 VDD_IN Power supply input; 6.0-48.0V Note 1
3 VDD_IN Power supply input; 6.0-48.0V
4 ENABLE Enable/ Disable power supply Note 2
5 GND Ground
6 GND Ground
Note 1. The STM32 Embedded Display system allows for the direct connection of an
additional display through the RiBUS connector on the board. You can connect any
intelligent display from Riverdi based on EVE4 (BT817Q). Please see chapter 10.6 for
detailed info.

Note 2. The "ENABLE" pin is internally pulled up to VDD_IN.

To enable the device, please leave the EN pin unconnected or short it to the "VDD_IN" pin.
To disable the device, short the EN pin to GND.

Note 3. Matched Riverdi power supply cable: RVA-0106M-1.25FF-1.

USB interface
The 1.25mm, 5-pin Molex connector labeled as “USB’ (P6) is USB interface.

NO. PIN DESCRIPTION NOTE

1 VCC_USB Power supply Note 1
2 D- USB data-

© 2024 Riverdi Page 10 of 17 www.riverdi.com

RVT50HQSNWC00-B

3 D+ USB data+
4 ID USB OTG ID; Host /Device detect Note 2
5 GND Ground
Note 1. The maximum current drawn from VCC_USB is 500mA.

Pin PJ0 of the MCU is dedicated to detecting USB over-current or short-circuit conditions.
If a USB over-current or short-circuit condition occurs, the LED 'USB OVR' will emit.

Note 2. Configuration of the USB Host/Device mode:

Host Mode: Pin 4 (ID) should be connected to GND.

In this mode, it can provide +5V output voltage to the connected USB device and Max
output current 500 mA.

Device Mode: Pin 4 (ID) should be not connected (floating).

Note 3. Matched Riverdi cable accessory: RVA-0105M-1.25FF

RS485 interface
The 1.25mm, 4-pin Molex connector labeled as “RS485’ (P7) is RS485 interface.

NO. PIN DESCRIPTION NOTE

1 VDD_IN Power supply input; 6.0-48.0V
Non-inverting receiver input and non-inverting driver
2 A
output
3 B Inverting receiver input and inverting driver output
4 GND Ground
Note 1. The termination resistor R18 (120 ohms) is mounted.

Note 2. Matched Riverdi cable accessory: RVA-0104M-1.25FF.

CAN FD interface
The 1.25mm, 4-pin Molex connector labeled as ’CANFD’(P5) is CANFD (Control Area
Network Flexible Data-Rate) communication bus, based on the high-speed (2.5-8.0Mbps)
CAN transceiver.

NO. PIN DESCRIPTION NOTE

1 GND Ground
2 CAN_L CAN Low-Level Voltage
3 CAN_H CAN High-Level Voltage
4 VDD_IN Power supply input; 6.0 – 48.0V
Note 1. Termination resistors R35, R36(both 60R) are mounted. Dip switch S3 is used to
enable and disable the termination resistors.

Enable: Set 1&2 to ON Disable: Set 1&2 to OFF

Note 2. The RXD pin of the CAN FD1 transceiver (TCAN1044A-Q1) is connected to the PB8
pin of the MCU to enable CAN Wake-Up functionality.
Additionally, the standby pin of CAN FD1 transceiver is connected to the PI6 pin of the
MCU.

Note 3. Matched Riverdi cable accessory: RVA-0104M-1.25FF

© 2024 Riverdi Page 11 of 17 www.riverdi.com

RVT50HQSNWC00-B

SWD (Serial Wire Debug) connector

The 1.25mm, 6-pin Molex connector labeled as ‘SWD’ (P3) is SWD interface, which is used
for programing the MCU on board.

NO. PIN DESCRIPTION NOTE

1 VCC_+3.3V Power input
2 SW_CLK Serial wire clock
3 GND Ground
4 SW_DIO Serial wire debug data input/output
5 RST Reset; Active low
6 SWO Serial wire trace output
Note 1. Compatible ST-LINK programmer: ST-LINK/V2, ST-LINK/V2-ISOL, ST-LINK/V3

Note 2. To program the board with ST-LINK/V2-ISOL, please use RVA-SWD-06M-C100 V2

RiBUS
Any size of the Riverdi EVE4 series display can be connected through RiBUS to act as a
slave module to the mainboard.

NO. PIN DESCRIPTION NOTE

1 VCC_+3.3V Supply voltage for module; TYP3.3V
2 GND Ground
3 SPI_SCLK SPI SCK signal
4 MISO/ IO.1 SPI MISO signal / SPI Quad mode: SPI data line 1
5 MOSI/ IO.0 SPI MOSI signal / SPI Quad mode: SPI data line 0
6 CS SPI chips select signal
Interrupt signal from device to the system,
7 INT
Active Low
8 RST/PD Reset / Power down signal, Active Low,
9 GPIO.0 GPIO.0
10 DISP_AUDIO Display audio in/out
SPI Single/Dual mode: General purpose IO0.
11 GPIO.1/IO.2
QSPI mode: SPI data line 2
SPI Single/Dual mode: General purpose IO1.
12 GPIO.2/IO.3
QSPI mode: SPI data line 3
13 NC Not connected
14 NC Not connected
15 NC Not connected
16 NC Not connected
17 BLVDD Supply voltage for backlight
Note 2
18 BLVDD Supply voltage for backlight
19 BLGND Backlight Ground, internally connected to GND
20 BLGND Backlight Ground, internally connected to GND
Note 1. Matched Riverdi FFC accessory for RiBUS: FFC0520150

Note 2. If any of the Riverdi EVE4 display series (3.5", 4.3", 5.0", or 7.0") is connected through
RiBUS, the power supply voltage VDD_IN should be between 6.0V-48.0V. To set up the
backlight voltage (BLVDD) at 5.0V, short the pads of the solder bridge labeled 'BLVDD INT'.

© 2024 Riverdi Page 12 of 17 www.riverdi.com

RVT50HQSNWC00-B

If any of the Riverdi EVE4 10.1" display series is connected through RiBUS, the power
supply voltage VDD_IN must range between 7.0V-14.0V. To set up the backlight voltage
(BLVDD) between 7.0V-14.0V, short the pads of the solder bridge labeled 'BLVDD EXT'

Expansion connector
The main board has one 1.27mm, 40-pin expansion pin socket which is labeled as P4 is
“EXPANSION CONNECTOR”.

It provides direct access to below GPIOs of MCU, which make it possible to easily extend a
daughterboard for a specific application.

• 2 x I2C
• 1 x UART
• 1 x USART
• 1 x SPI
• 1 x USB
• 7 x PWMs
• 1 x DAC(Digital-to-analog)
• 2 x ADCs (Analog-to-digital)

Each of the GPIO pins can be configured by software as output (push-pull or open-drain,
with or without pull-up or pull-down), as input (floating, with or without pull-up or pull-
down) or as peripheral alternate function. Most of the GPIO pins are shared with digital or
analog alternate functions. Please refer to the datasheet of MCU for more details.

© 2024 Riverdi Page 13 of 17 www.riverdi.com

RVT50HQSNWC00-B

I/O/P PIN NAME NO. NO. PIN NAME I/O/P

P VCC_+5V 1 2 VCC_+3.3V P
P VCC_+5V 3 4 VCC_+3.3V P
I/O PA5 5 6 GND P
P GND 7 8 PA4 I/O
N/A RESERVED* 9 10 PB15 I/O
I/O P15 11 12 PB1 I/O
I/O PB6 13 14 PC7 I/O
I/O PB7 15 16 P10 I/O
P GND 17 18 GND P
I/O PG3 19 20 PA7 I/O
I/O PG4 21 22 PA6 I/O
I/O PG2 23 24 PH11 I/O
I/O PG9 25 26 PA3 I/O
I/O PG10 27 28 GND P
I/O PB10 29 30 PB2 I/O
I/O PB5 31 32 PA8 I/O
I/O PB0 33 34 PH5 I/O
I/O P14 35 36 PH4 I/O
I/O PA15 37 38 PA10 I/O
I/O PA11 39 40 PA12 I/O
Note 1. The total output current [email protected] from pin 1 and pin3 is maximum 1A.

The total output current [email protected] from pin 2 and pin 4 is maximum 500mA.

*Do not use

Micro SD card slot

The mainboard is equipped with Micro-SD slot, which supports all types of Micro SD cards.

Battery coin cell holder

The battery coin cell, labeled as BT1, is suitable for CR1220 (Ø12.5 x 2.0mm) Coin Cell
Batteries.

The BT1 is connected to the VBAT pin of MCU, which allows to retain the content of the
backup registers, SRAM to keep running RTC when the VDD_IN is turned off and
unplugged.

USER INTERFACES

2 x push button
Push button labeled as ‘RST’ (S2) is used to reset the module.

Another 1 push button labeled as ‘USR BTN’ is for user’s development.

• USR BTN(S1) is connected to GPIO, PH3-BOOT0, of the MCU.

© 2024 Riverdi Page 14 of 17 www.riverdi.com

RVT50HQSNWC00-B

3 x LEDs
1 x LED, labeled as ‘PWR LED’, emits green light when the modules is powered.

1 x LED, labeled as ‘USB OVR’, emits red light when VCC_USB pin overcurrent occurs.

1 x LED, labeled as ‘USR LED’, is for user’s development.

• The ‘USR LED’ is connected to GPIO, PE5, of the MCU.

© 2024 Riverdi Page 15 of 17 www.riverdi.com

RVT50HQSNWC00-B

DISPLAY SEPCIFICATION

Full TFT specification

The TFT of the module applies Riverdi high brightness, IPS, 5.0” RGB TFT：
RVT50HQTNWC00-B

For detailed information, please refer to datasheet of display.

RELIABILITY TEST

NO. TEST ITEM TEST CONDITION NOTE

1 High Temperature Storage 80°C/120 hours
2 Low Temperature Storage -30°C/120 hours
3 High Temperature Operating 70 °C /120 hours Note 1
4 Low Temperature Operating -20°C/120 hours
5 High Temperature and High Humidity Humidity 40℃, 90%RH, 120Hrs
-20℃ for 30mins, 70℃ for 30
mins.
6 Thermal Cycling Test (No operation)
100 cycles. Then test at room Note 2
temperature after 1 hour
Frequency: 10 ÷ 55 Hz.
Stroke: 1.5 mm.
Sweep: 10Hz ÷ 55Hz ÷ 10 Hz.
7 Vibration Test
2 hours for each direction of X,
Y, Z
(Total 6 hours)
Height: 60 cm
8 Package Drop Test
1 corner, 3 edges, 6 surfaces
Note 1. Sample quantity for each test item is 5 ÷ 10 pcs.
Note 2. Before cosmetic and function test, the product must have enough recovery time,
at least 2 hours at room temperature.

© 2024 Riverdi Page 16 of 17 www.riverdi.com

RVT50HQSNWC00-B

LEGAL INFORMATION
CE marking is usually obligatory only for a complete end product. Riverdi display modules
are semi-finished goods which are used as inputs to become part of the finished products.

Therefore, Riverdi display modules are not CE marked.

Riverdi grants the guarantee for the proper operation of the goods for a period of 12 months
from the date of possession of the goods. If in a consequence of this guaranteed execution
the customer has received the defects-free item as replacement for the defective item, the
effectiveness period of this guarantee shall start anew from the moment the customer
receives the defects-free item.

Information about device is the property of Riverdi and may be the subject of patents
pending or granted. It is not allowed to copy or disclosed this document without prior
written permission.

Riverdi endeavors to ensure that all contained information in this document is correct but
does not accept liability for any error or omission. Riverdi products are in developing process
and published information may be not up to date. Riverdi reserves the right to update and
makes changes to Specifications or written material without prior notice at any time. It is
important to check the current position with Riverdi.

Images and graphics used in this document are only for illustrative the purpose. All images
and graphics are possible to be displayed on the range products of Riverdi, however the
quality may vary. Riverdi is no liable to the buyer or to any third party for any indirect,
incidental, special, consequential, punitive, or exemplary damages (including without
limitation lost profits, lost savings, or loss of business opportunity) relating to any product,
service provided or to be provided by Riverdi, or the use or inability to use the same, even if
Riverdi has been advised of the possibility of such damages.

Riverdi products are not fault tolerant nor designed, manufactured or intended for use or
resale as on line control equipment in hazardous environments requiring fail–safe
performance, such as in the operation of nuclear facilities, aircraft navigation or
communication systems, air traffic control, direct life support machines or weapons
systems in which the failure of the product could lead directly to death, personal injury or
severe physical or environmental damage (‘High-Risk Activities’). Riverdi and its suppliers
specifically disclaim any expressed or implied warranty of fitness for High-Risk Activities.
Using Riverdi products and devices in 'High-Risk Activities' and in any other application is
entirely at the buyer’s risk, and the buyer agrees to defend, indemnify, and hold harmless
Riverdi from all damages, claims or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Riverdi intellectual property rights.

© 2024 Riverdi Page 17 of 17 www.riverdi.com