FERROTECT INDUSTRIAL ENAMEL
Alkyd Enamel Finish
General purpose enamel with good anti rust properties
Can be applied over intact alkyd , epoxy and PU coatings
Super-gloss Finish and Retention
Strong Resistance to Wear and Abrasion
Resistant to Mild Corrosive Chemicals
Ferrotect Industrial Enamel is the most advanced gloss paint with excellent film integrity and built-
in-toughness. It extends a luxurious, brilliant glossy finish to the surface for years. Its abrasion
resistance qualities, along with ability to resist corrosive chemicals keeps your painted surface
smooth and smart even against the most severe punishment.
Recommended Usage
• Metal Surfaces
• Wood Recommended for use on metal and wood surfaces in both interior and exterior.
Surfaces
General Properties
Finish High Gloss Flexibility Excellent - ¼ inch (As per IS 101)
Excellent - 900-1000 gms (As per
Opacity Excellent Hardness
IS 101)
Flow and Levelling Excellent Consistency Smooth & Uniform
Weather
Durability 3 yrs Satisfactory
Resistance
Gloss Levels/Sheen
85 - 90% at 60 deg
Levels Acid & Alkali
Resistant to mild Acid & Alkali
Resistance
Light Fastness Satisfactory
Safety, Environment & Health
Flammable – Avoid Exposure to flame Flash Point - Not below 30 oC
Application
Surface Preparation: Brush
1. Cleaning: Free the surface from grease, rust, moisture, loose Application Roller
particles and peeling/flaking paint. Oil and grease should be
removed as per SSPC -SP1 solvent cleaning. Spray
2. Priming: Suitable alkyd / epoxy primer or intermediate coat 0-5% by volume
Brush
, dry and free from any contamination. with J&N GP
Roller Thinner
Ferrous Metal Surface - Apply 1-2 coats of J&N Super Red
0-5% by volume
Oxide Primer on the metal surface by thinning (if Airless
Dilution with J&N GP
necessary) with J&N GP Thinner. Allow drying for 8-10 hrs Spray Thinner
after each coat. 10-15% by
Spray volume with J&N
Non-Ferrous Metal Surface - Apply 1-2 coat of Zinc GP Thinner
Chrome Yellow Primer on the metal surface by thinning (if Drying time at Touch Dry : 4 hours
necessary) it with J&N GP Thinner. Allow drying for 8 hrs. 30 C Handle : 8 hours
Hard Dry :Overnight
Wooden Surface - Apply first coat of J&N Pink/White
Primer on the wooden surface by thinning (if necessary) Over coating
Overnight
with J&N GP Thinner. Allow drying for 5-6 hrs. Use any interval at 30 C
synthetic Putty to fill minor cracks, dents or holes. After No. of coats
drying sand the surface with Emery Paper 180. Apply 2 - 3 coats
specified
another coat of J&N Pink/White Primer. Allow drying for
5-6 hrs.
*17.0 sq mt / lt per coat
Application (Topcoat): Coverage at 20 micron dft
Apply two coats of Ferrotect Industrial Enamel after thorough (Theoretical) * 13.5 sq mt/ litre at 25
stirring and diluting (if required) with J&N GP Thinner. Maintain micron dft
an interval of 6-8 hrs between successive coats. under normal conditions
Stability of Thinned
Use within 24 hrs.
Paint
0 0
• Substrate Temperature should be at least 10 C. but not above 50 C.
Precautions while • Painting is not recommended if the moisture content and alkalinity of the surface is high.
Painting • Relative humidity should be below 85 %
• Please do not over-thin or over-extend the brush while painting.
Cleaning up
All equipments should be cleaned with J&N GP Thinner.
equipments
Post Application To remove stains, sponge clean with a mild soap solution and wipe clean. Before cleaning, please
Instructions ensure a drying time of one week.
General Information
Mix thoroughly before starting and in Colour • Range
Mixing
between as well Options
• Ferrous Metal - Superior Red Oxide
Primer
Preferable Regulatory VOC :350 +- 25 gm / lt ( depending
• Non Ferrous Metal - Zinc Chrome
Primer Information on shades )
Yellow Primer
• Wood - White/Pink Primer
Preferable • 20 Ltr Packs
• Wood – Synthetic Putty Packing
Putty
General Safety and Environment Information
• Keep container upright and tightly closed in a cool, dry and • Wear appropriate attire, especially gloves, eye protection and
well ventilated location away from heat source, flammables nose mask.
and direct sunlight. • Work in a well-ventilated area. Do not breathe vapour or spray.
• Keep out of reach of children. Do not store near food, drinks • Remove paint from skin by washing with water and soap or
or animal feed. appropriate cleaner.
• Dispose unwanted paint safely. Do not dispose into drains, • Avoid contact with skin as it may cause irritation.
water sources or open sewers. • In the case of accidental contact, wash area immediately with
• Wash all tools after application with General Purpose Thinner water and seek immediate medical attention.
or Mineral Turpentine. • To remove the paint from skin, use soap and water or
• Use sand or earth to contain any paint spillage. appropriate cleaner.
*Actual Coverage may vary depending upon the application process and surface conditions.
The information given is intended to give a description of the product performance under specific test conditions. Nevertheless, we cannot assume any
responsibility for the use of it since circumstances under which the products are applied in practice are subjected to many variations. We reserve the right to
alter the given data without notice.
