Alpha series - Front end cylinder with outer cover
FC A191-5-08130-004-K0343 Item no. 70527716
Tipping weight 56 - 79 ton
* incl. 20 [-5; +30] mm pull out 3D model is available on request
Specifications Max. pump flow Tipping time
Max. working pressure 220 bar With KO¹ 190 L/min With KO¹ 47 sec
Weight 468 kg Without KO¹ 170 L/min Without KO¹ 52 sec
Working volume 148 L With KO¹ below -20°C 133 L/min With KO¹ below -20°C 67 sec
Total volume 159 L Without KO¹ below -20°C 119 L/min Without KO¹ below -20°C 74 sec
Max. cyl. load (start tipping) 345 kN Allowable lowering time 47 sec
Max. cyl. load (end of stroke)² 150 kN
Max. cyl. load (end of stroke)³ 175 kN Extension 1 2 3 4 5 6 7 Total
Effective diameter [mm] 191 169 149 129 110
Stroke* [mm] 1610 1630 1630 1630 1630 8130
Technical notes
This cylinder is a lifting device only. It should not be used as a structural member and should not be subjected to side loads. Tipping valve must
have a pressure relief at the cylinder port set not higher than max. working pressure. Verify max. cyl. load. Working temperature range is between
-40°C and +80°C. Max. duration of extension is 0.5 hours (excluded hard chromed stages). Cylinder is painted black (RAL9005) with a min.
thickness conforming to the 480 hours neutral salt spray test as per ISO 9227. ¹ Hyva knock-off. ² Unsubstantial unloading (sticky load).
³ Substantial unloading.
Related documentation
Bracket options: 015BRA10 & 015BRA12 Mounting instructions: CYL-0030 Oil specifications: OIL-0011
Spec sheet explanation: CYL-0041
Tipping weight
BL body length BL [mm] 10800 10350 9900
OH rear overhang OH [mm] 200 500 800 200 500 800 200 500 800
Ycog vert. pos. centre At [°] 44 46 47 46 48 49 49 50 52
of gravity
Qo pivot length Ycog [mm]
C bracket length 600 56 59 62 57 61 65 59 63 67
At tipping angle 900 59 62 66 60 64 69 63 67 73
stroke x 60 / Qo 1200 61 65 70 64 68 74 67 72 79
Tipping weight [ton] at maximum pressure of 220 bar for a vertically mounted cylinder and C is 229 mm
For detailed tipping calculations please refer to: https://tipper.hyva.com
Subject to change without notice, no rights reserved Page 1/2 DO-E 70527716 / 2017-7-28 / RV AB
Alpha series - Front end cylinder with outer cover
FC A191-5-08130-004-K0343 Item no. 70527716
Pos. Part no. Description Qty.
1
C01 71839050 DUST COVER FC LOW 15-273 1
C02 71737793 COVER 273-1685 PIN60 A360 SPH LOCK 1
C03 01702956 K WASHER M48 DIN 125B ZP 1
C04 01702907 K TOPNUT NYLOC M48x3 DIN 985 ZP 1
C05 01791953 O-RING COVER D.273 1
C06 15014550 K BOLT HSHC M12X30X1.75 Q8.8 DIN 912 ZP 1
P01 74403771 PISTON FL2 S 110-1885-HC 1
P02 71853110 K SLIDER FL 110 (2 X 1/2) A22 1
P03 71851110 K OUTER STOPRING FL 110 A22 1
P04 71822110 BOTTOM PLATE PISTON FL 110 1
P05 01745050 K CIRCLIP 100 DIN 472 (105.5x3.0) 1
P06 71870220 K O-RING PISTON BOTTOM 110 1
P07 71848300 PISTON HEAD FL 110 MK2 1
P08 01226538 K O-RING 91.67 X 3.53 MM NBR 1
S41 74604770 STAGE FL2 129-1880 1
S42 71802129 K PACKSET FL 129/HP 129 1
S43 71853129 K SLIDER FL 129 (2 X 1/2) A22 1
S44 71851129 K OUTER STOPRING FL 129 A22 1
S45 71852129 K LIFTRING FL 129 A22 1
S31 74605770 STAGE FL2 149-1880 1
S32 71802149 K PACKSET FL 149/HP 150 1
S33 71807151 K SLIDER FL 149 A35 1
S34 71851149 K OUTER STOPRING FL 149 A22 1
S35 71852149 K LIFTRING FL 149 A22 1
S21 74606770 STAGE FL2 169-1880 1
S22 71802169 K PACKSET FL 169 1
S23 71807171 K SLIDER FL 169 A35 1
S24 71851169 K OUTER STOPRING FL 169 A22 1
S25 71813169 K LIFTRING FL 169x5 1
S11 74607770 STAGE FL2 191-1880 1
S12 71802191 K PACKSET FL 191 1
S13 71807193 K SLIDER FL 191 A35 1
S14 71851191 K OUTER STOPRING FL 191 A22 1
S15 71813191 K LIFTRING FL 191x5 1
B01 74508770R1585 BASE FL2 214-1931-4/4BSAE-190-C273 1
B02 71802214 K PACKSET FL 214 1
B03 71825435 BOTTOM PLATE FL2 214 1
B04 71870045 K SEAL BOTTOM PLATE FL 214 1
B05 71820214 LOCKING PLATE FL 214 3
B06 01732020 K BOLT HEX M12X25X1.25 SET 6 PCS 1
B07 01732523 K WASHER SPRING M12 SET 6 PCS 1
Seal kit complete Notes
71908750 K Consists of all packsets with packset grease and O- The inner stopring is pre-mounted in the grooves on spare bases and
rings stages.Therefore, when ordering new tubes, it is not required to order inner stoprings
separately.
For repair instructions see: CYL-0040. Serial no. is located on type plate and near type plate support.
Subject to change without notice, no rights reserved Page 2/2 DO-E 70527716 / 2017-7-28 / RV AB
