MMA1Z00-NS400-C

Mellanox® MMA1Z00-NS400 Compatible TAA 400GBase-SR4 QSFP112 Transceiver (MMF, 850nm, 50m, MPO,
DOM, CMIS 5.0)

Features:
• QSFP112 MSA Compliant
• 4x100G PAM4 retimed 400GAUI-4 electrical interface
• Compliant with IEEE 802.3db
• Compliant to IEEE 802.3ck
• Operating Temperature: 0 to 70 Celsius
• 4 channel VCSEL arrays and 4 channels PIN photo detector
arrays
• MPO-12 APC Connector
• CMIS 5.0
• Class 1 Laser
• Hot Pluggable QSFP112 Form Factor
• RoHS Compliant and Lead-Free

Applications:
• 400GBase Ethernet

Product Description
This Mellanox® MMA1Z00-NS400 compatible QSFP112 transceiver provides 400GBase-SR4 throughput up to
50m over multi-mode fiber (MMF) using a wavelength of 850nm via an MPO connector. It is guaranteed to be
100% compatible with the equivalent Mellanox® transceiver. This easy to install, hot swappable transceiver has
been programmed, uniquely serialized and data-traffic and application tested to ensure that it will initialize and
perform identically. Digital optical monitoring (DOM) support is also present to allow access to real-time
operating parameters. This transceiver is Trade Agreements Act (TAA) compliant. We stand behind the quality
of our products and proudly offer a limited lifetime warranty.

ProLabs’ transceivers are RoHS compliant and lead-free.

TAA refers to the Trade Agreements Act (19 U.S.C. & 2501-2581), which is intended to
foster fair and open international trade. TAA requires that the U.S. Government may
acquire only “U.S. – made or designated country end products.”
Rev. 092324
Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Notes

Power Supply Voltage Vcc -0.5 3.6 V

Storage Temperature Tstg -40 85 oC
Operating Case Temperature Tc 0 70 oC
Relative Humidity (non-condensing) RH 15 85 %
Receiver Damage Threshold, per Lane PRdmg 5 dBm
Bit Rate BR 425 Gbps
Fiber Length on OM3 MMF 60 m
Fiber Length on OM4 MMF 100 m
I2C Clock Frequency 0 10 1000 kHz

Notes:
1. Exceeding the Absolute Maximum Ratings table may cause permanent damage to the device. This is just
an emphasized rating and does not involve the functional operation of the device that exceeds the
specifications of this technical specification under these or other conditions. Long-term operation under
Absolute Maximum Ratings will affect the reliability of the device.

Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes

Power Supply Voltage Vcc 3.135 3.3 3.465 V

Total Power Consumption Pc 9 W 1
Supply Current per end 2.72 A
Pre FEC Bit Error Ratio 2.4E-4
Post FEC Bit Error Ratio 1E-12
Transmitter (each lane)

Differential pk-pk Input Voltage Tolerance 750 mV

Differential Termination Mismatch 10 %
Eye Height EH 10 mV
Common-Mode to Differential-Mode Return Loss RLDc IEEE802.3ck Equation (120G–1) dB
Vertical Eye Closure VEC 12 dB
Effective Return Loss ERL 7.3 dB
Transition Time 10 ps
Receiver (each lane)

Differential Data Output Swing 300 900 mVpp

Differential Termination Mismatch 10 %
 Eye Height EH 15 mV
Vertical Eye Closure VEC 12 dB
Common-Mode to Differential-Mode Return RLDc IEEE802.3ck Equation (120G–1) dB
Loss
Effective Return Loss ERL 8.5 dB
Transition Time 8.5 ps

Notes:
1. Under condition of 3.465V operating supply voltage, and 70℃ case temperature.

Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes

Transmitter

Data Rate per lane DR 53.125 GBd

Modulation Format PAM4
Center Wavelength λ 844 850 863 nm 1
RMS Spectral Width σ 0.6 nm
Average Launch Power, each lane Pavg -4.6 4 dBm

Optical Power OMA, each Lane，max POMA 3.5 dBm

OMAouter, max (TECQ, TDECQ) <1.8 dB max [-2.6 , max(TECQ,TECQ) – 4.4] dBm
each lane min 1.8 < max (TECQ, TDECQ) < 4.4 dB
Transmitter and Dispersion Eye Closure TDECQ 4.4 dB
(TDECQ), each lane
Transmitter Eye Closure for PAM4 (TECQ), each TECQ 4.4 dB
lane
Extinction Ratio ER 2.5 dB
Transmitter Power Excursion, each lane 2.3 dBm
Optical Return Loss Tolerance ORLT 14 dB
Optical Power for TX DISABLE -30 dBm
Encircled Fluxb ≥86% at 19 um 2
≤30% at 4.5 um
Receiver

Data Rate per lane BR 53.125 GBd

Modulation Format PAM4
Center Wavelength λ 844 850 863 nm
Damage Threshold 5 dBm
Average Receive Power, each Lane AOPR –6.4 4 dBm
Receive Power (OMAouter), each Lane OMAR 3.5 dBm
 Receiver Reflectance RR –15 dB
Receiver Sensitivity, each Lane S RS = max (-4.6 , TECQ – 6.4) dBm 3
Stressed Receiver Sensitivity, each Lane SRS -2.0 dBm
RX LOS Assert -15 dBm
De-assert -7.5 dBm
Hysteresis 0.5 5 dB

Notes:
1. Defined according to the performance of the laser used.
2. Measured into type A1a.2 or type A1a.3, or A1a.4, 50 um fiber, in accordance with IEC 61280-1-4.
3. Receiver sensitivity is informative and is defined for a transmitter with a value of TECQ. Measured with
conformance test signal at TP3 for BER = 2.4E-4 Pre-FEC.

QSFP-DD Rx Output Equalization Code Table

Byte Bits Field Name Field Description

6 Simultaneous Host and Media Side loopbacks 0b: not supported

5 Per Lane Media Side Loopbacks 1b: supported
4 Per Lane Host Side Loopbacks 1b: supported
13h:128 3 Host Side Input Loopback 1b: supported
2 Host Side Output Loopback 1b: supported
1 Media Side Input Loopback 1b: supported
0 Media Side Output Loopback 1b: supported

Pin Descriptions
Pin Logic Symbol Name/Description Power Sequence Notes

1 Ground GND 1B 1
2 CML-I Tx2n Transmitter Inverted Data Input 3B
3 CML-I Tx2p Transmitter Non-Inverted Data Input 3B
4 Ground GND 1B 1
5 CML-I Tx4n Transmitter Inverted Data Input 3B
6 CML-I Tx4p Transmitter Non-Inverted Data Input 3B
7 Ground GND 1B 1
8 LVTTL-I ModSelL Module Select 3B
9 LVTTL-I ResetL Module Reset 3B
10 VccRx +3.3V Power Supply Receiver 2B 2
11 LVCMOS-I/O SCL 2-wire serial interface clock 3B
 12 LVCMOS-I/O SDA 2-wire serial interface data 3B
13 Ground GND 1B 1
14 CML-O Rx3p Receiver Non-Inverted Data Output 3B
15 CML-O Rx3n Receiver Inverted Data Output 3B
16 Ground GND 1B 1
17 CML-O Rx1p Receiver Non-Inverted Data Output 3B
18 CML-O Rx1n Receiver Inverted Data Output 3B
19 Ground GND 1B 1
20 Ground GND 1B 1
21 CML-O Rx2n Receiver Inverted Data Output 3B
22 CML-O Rx2p Receiver Non-Inverted Data Output 3B
23 Ground GND 1B 1
24 CML-O Rx4n Receiver Inverted Data Output 3B
25 CML-O Rx4p Receiver Non-Inverted Data Output 3B
26 Ground GND 1B 1
27 LVTTL-O ModPrsL Module Present 3B
28 LVTTL-O IntL Interrupt 3B
29 VccTx +3.3V Power supply transmitter 2B 2
30 Vcc1 +3.3V Power supply 2B 2
31 LVTTL-I LPMode Low Power mode 3B
32 Ground GND 1B 1
33 CML-I Tx3p Transmitter Non-Inverted Data Input 3B
34 CML-I Tx3n Transmitter Inverted Data Input 3B
35 Ground GND 1B 1
36 CML-I Tx1p Transmitter Non-Inverted Data Input 3B
37 CML-I Tx1n Transmitter Inverted Data Input 3B
38 Ground GND 1B 1

Notes:
1. GND is the symbol for signal and supply (power) common for the QSFP112 module. All are common within
the QSFP112 module and all voltages are referenced to this potential unless otherwise noted. Connect these
directly to the host board signal-common ground plane.
2. Vcc Rx, Vcc1 and VccTx are the receiver and transmitter power supplies and shall be applied concurrently.
VccRx, Vcc1 and VccTx may be internally connected within the QSFP112 module in any combination. The
connector pins are each rated for a maximum current of 1.5A (max. current of 2.0 A is required for high
module power of 15-20W).
Electrical Pad Layout

Functional Block Diagram

Mechanical Specifications
About ProLabs
Our experience comes as standard; for over 15 years ProLabs has delivered optical connectivity solutions that
give our customers freedom and choice through our ability to provide seamless interoperability. At the heart
of our company is the ability to provide state-of-the-art optical transport and connectivity solutions that are
compatible with over 90 optical switching and transport platforms.

Complete Portfolio of Network Solutions

ProLabs is focused on innovations in optical transport and connectivity. The combination of our knowledge of
optics and networking equipment enables ProLabs to be your single source for optical transport and
connectivity solutions from 100Mb to 400G while providing innovative solutions that increase network
efficiency. We provide the optical connectivity expertise that is compatible with and enhances your switching
and transport equipment.

Trusted Partner
Customer service is our number one value. ProLabs has invested in people, labs and manufacturing capacity
to ensure that you get immediate answers to your questions and compatible product when needed. With
Engineering and Manufacturing offices in the U.K. and U.S. augmented by field offices throughout the U.S.,
U.K. and Asia, ProLabs is able to be our customers best advocate 24 hours a day.

Contact Information
ProLabs US
Email: [email protected]
Telephone: 952-852-0252

ProLabs UK
Email: [email protected]
Telephone: +44 1285 719 600