HYDRAULIC EXCAVATOR

MAINTENANCE SPECIFICATIONS
SHOP SK200-8
MANUAL model SK210LC-8
(HS Engine)

INDEX
1 SPECIFICATIONS SECTION

SYSTEM
2 MAINTENANCE SECTION
3 SYSTEM SECTION
4 DISASSEMBLY SECTION

DISASSEMBLING
5 TROUBLESHOOTING
6 ENGINE SECTION
7 PROCEDURE E / G TROUBLESHOOTING
OF INSTALLING
OPTIONS SECTION OPT.

Book Code No.S5YN0023E02

0-1
 SK200-8
ASIA (HS Engine) INDEX SK210LC-8
Book Code No. Index
Title
Distribution Year–Month No.

MAINTENANCE SPECIFICATIONS
S5YN0118E01
2007-4
OUTLINE 1
S5YN0223E01
2007-4
SPECIFICATIONS 2
S5YN0323E01
ATTACHMENT DIMENSIONS 3
2007-4
S5YN1118E02
TOOLS 11
2008-10
S5YN1223E01 STANDARD MAINTENANCE
2007-4
12
TIME SCHEDULE
S5YN1318E02 MAINTENANCE STANDARD
2007-4
13
AND TEST PROCEDURE
S5YN2123E02 MECHATRO CONTROL
2008-10
21
SYSTEM
S5YN2223E01
2007-4
HYDRAULIC SYSTEM 22
S5YN2323E01

SYSTEM
2007-4
ELECTRIC SYSTEM 23
S5YN2423E02
2008-10
COMPONENTS SYSTEM 24
S5YN2523E01
2007-4
AIR-CONDITIONER SYSTEM 25
_

S5YN3118E01 DISASSEMBLING
DISASSEMBLING

2007-4 & ASSEMBLING

31
S5YN3218E02
ATTACHMENT 32
2007-4
S5YN3323E02
2008-10
UPPER STRUCTURE 33
S5YN3423E01
2007-4
TRAVEL SYSTEM 34
E / G TROUBLESHOOTING

S5YN4618E03
2008-10
BY ERROR CODES 46
S5YN4718E01
2007-4
BY TROUBLE 47
S5YN4818E01
2007-4
TROUBLE DIAGNOSIS MODE 48
_

S5YN5123E02
ENGINE 51
2008-10
_

YN11-45001~
YQ11-06001~ APPLICABLE MACHINES

0-5
NOTE:
This Manual is prepared as a technical material in This Manual may be properly revised due to the im-
which the information necessary for the maintenance provement of products, modification of specifications,
and repairing services of our hydraulic excavators are etc. And there are cases where the system on actual
collected, and is categorized into 7 Chapters, Specifica- machine and a part of the contents of this manual may
tion, Maintenance, System, Disassembly, Trouble- differ due to the variations of specification by countries.
shooting, Engine, and Installation Procedures for For the section in which the description is hardly under-
Optional Attachment. stood, contact our distributor.

• The Chapter "Specification" describes the specifi- The number is assigned to every part handled in this
cations for entire machine and material, which are Manual on account of the description, but the parts,
instructive for replacement and repairing of attach- which cannot be supplied as service parts are con-
ments. tained. Therefore, the order must be placed with re-
spective formal number with due confirmation on the
• The Chapter "Maintenance" describes the material,
Parts Manual for applicable machine.
which is helpful for maintenance service and adjust-
ments for entire machine.
• The Chapter "System" describes the operating sys-
tem like hydraulic system, electric system, compo-
nents, and so on.
• The Chapter "Disassembly" describes the removal
and installing of assembly mounted on the upper
structure and undercarriage, and the assembling
and disassembling of the associated hydraulic
equipment.
• The Chapter "Troubleshooting" describes how to
find the fault equipment.
• The Chapter "Engine" describes the engines mak-
ing use of the "Maintenance Manual" provided by
the suppliers.
• The Chapter "Installation Procedures for Optional
Attachment" describes the supplements added on
request as required.

0-6
https://www.ebooklibonline.com

Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.

https://www.ebooklibonline.com
 1

1. OUTLINE
TABLE OF CONTENTS

1.1 GENERAL PRECAUTIONS FOR MAKING REPAIRS ......................................................1-3

1.1.1 PREPARATION BEFORE DISASSEMBLING..........................................................1-3
1.1.2 SAFETY WHEN DISASSEMBLING AND ASSEMBLING ........................................1-3
1.1.3 DISASSEMBLING AND ASSEMBLING HYDRAULIC EQUIPMENT .......................1-3
1.1.4 ELECTRICAL EQUIPMENT .....................................................................................1-4
1.1.5 HYDRAULIC PARTS ................................................................................................1-5
1.1.6 WELD REPAIR .........................................................................................................1-5
1.1.7 ENVIRONMENTAL ISSUES.....................................................................................1-5
1.2 INTERNATIONAL UNIT SYSTEM .....................................................................................1-6

Book Code No. S5YN0118E01

1-1
1. OUTLINE

Issue Date of Issue Applicable Machines Remarks

SK330-8 : LC10-07001~ S5YN0118E01
First edition July, 2006 K
SK350LC-8 : YC10-03501~ (ASIA, OCE)
SK200-8 : YN11-45001~ ↑
↑ August, 2006 K
SK210LC-8 : YQ11-06001~ (ASIA, OCE)
SK250-8: LQ12-06001~ ↑
↑ October, 2006 K
SK260LC–8 : LL12-05001~ (ASIA, OCE)
↑ December, 2006 SK850LC: LY01-00101~ ↑ K
E235BSR : YF05-02001~ ↑
↑ February, 2007 K
E235BSR(N)LC : YU05-02001~ (NHK)
↑
↑ ↑ SK235SRLC-2 : YU05-02001~ K
(North America)
E215B : YN11-45001~ ↑
↑ March, 2007 K
E215BLC : YQ11-06001~ (NHK Russia)
SK235SR-2 : YF05-02001~ ↑
↑ April, 2007 K
SK235SRLC-2 : YU05-02001~ (OCE)
SK200-8 : YN11-45001~ ↑
↑ April, 2007 K
SK210LC-8 : YQ11-06001~ ASIA (HS Engine)

1-2
 1. OUTLINE

1.1 GENERAL PRECAUTIONS FOR 2) Attach "Don’t operate" tag to control lever, and
MAKING REPAIRS begin a meeting before starting the work.
3) Before starting inspection and maintenance
1.1.1 PREPARATION BEFORE stop the engine.
DISASSEMBLING
4) Confirm the position of first-aid kit and fire
extinguisher, and also where to make contact
Read Operator's Manual
for emergency measure and ambulance to
before disassembling

prepare for accidents and fire.

(1) Knowledge of operating procedure
5) Choose a hard, lever and safe place, and put
Read Operator’s Manual carefully to understand
attachment on the ground without fail.
the operating procedure.
6) Use hoist, etc. to remove parts of heavy weight
(2) Cleaning machines
(23kg [50 lb] or more).
Clean machines of soil, mud, and dust before
carrying into the service shop. 7) Use proper tools, and change or repair
Carrying a soiled machine into the service shop, defective tools.
causes making less efficient work and damage of 8) Machine and attachment required to work in the
parts. lifting condition should be supported with
(3) Inspecting machines supports or blocks securely.
Confirm the disassembling section before starting 1.1.3 DISASSEMBLING AND ASSEMBLING
work, determine the disassembly procedure taking HYDRAULIC EQUIPMENT
the conditions in work shop into account, and
request to procure necessary parts in advance.
(4) Recording
Record the following items to keep contact and (1) Removing hydraulic equipment assy
prevent malfunction from recurring. 1) Before removing pipes, release the pressure of
1) Inspecting date, place hydraulic oil tank, or open the cover on the
2) Model name, Serial number and Record on return side to tank, and take out the filter.
hour meter 2) Drain the oil in the removed pipes into pan to
3) Trouble condition, place, cause prevent the oil from spilling on the ground.
4) Visible oil leak, water leak and damage 3) Pipes with plugs or caps to prevent oil leaking,
entry of dust, etc.
5) Clogging of filters, oil level, oil quality, oil
contamination and looseness. 4) Clean the outside surface of equipment, etc.
before disassembling, and drain hydraulic oil
6) Examine the problems on the basis of monthly
and gear oil before putting them on working
operation rate with the last inspection date and
bench.
records on hour meter.
(2) Disassembling hydraulic equipment
(5) Arrangement and cleaning in service shop
1) Since performance and function of hydraulic
1) Tools required for repair work.
equipment after disassembly and assembly
2) Prepare the places to put the disassembled
results in immunity from responsibility on the
parts.
manufacture’s side, disassembly, assembly
3) Prepare oil pans for leaking oil, etc. and modification without permission are strictly
prohibited.
1.1.2 SAFETY WHEN DISASSEMBLING AND
ASSEMBLING 2) If it is unavoidably necessary to disassemble
and modify, it should be carried out by experts
or personnel qualified through service training.
WARNING
3) Make match mark on parts for reassembling.
(1) Safety 4) Before disassembling, read Disassembling
1) Wear appropriate clothing, safety shoes, safety Instruction in advance, and determine if the
helmet, goggles, and clothes with long sleeves. disassembly and assembly are permitted or
not.

1-3
1. OUTLINE

5) For parts which are required to use jig and

tools, don’t fail to use the specified jig and tools.
6) For parts which can not be removed in the
If hydraulic oil and lubricating oil are not
specified procedure, never force removal. First
filled and also air bleed is not performed,
check for the cause.
the hydraulic equipment may be damaged.
7) The removed parts should be put in order and
tagged so as to install on proper places without 3) For air bleed of hydraulic pump and swing
confusion. motor, loosen drain plug on the upper part, start
8) For common parts, pay attention to the quantity engine, and run in low idling, then bleed air until
and places. hydraulic oil is comes out. After completion of
comes, tighten plug securely.
(3) Inspecting parts
4) For air bleed of travel motor and hydraulic
1) Check that the disassembled parts are free
cylinder, starts engine and operate it for 10
from adherence, interference and uneven
minutes or more at no-load and low speed.
working face.
2) Measure the wear of parts and clearance, and
record the measured values.
3) If an abnormality is detected, repair or replace For cylinder, don’t move it to the stroke end
the parts. at beginning.
(4) Reassembling hydraulic equipment
5) Air in pilot circuit can be bleed out by only
1) During the parts cleaning, ventilate the room. operating digging, swing and traveling motions
2) Before assembly, clean parts roughly first, and thoroughly.
then completely. 6) Check hydraulic oil level.
3) Remove adhering oil by compressed air, and Move attachments to hydraulic oil check
apply hydraulic oil or gear oil, and then position, and check hydraulic oil level of tank.
assemble them. Refill oil if the oil level is lower than the specified
4) Replace the removed O-ring, back-up rings and level.
oil seal with new ones, and apply grease oil on How to check oil level of hydraulic oil tank
them before assembling.



 
5) Removes dirt and water on the surface on
which liquid sealant are applied, decrease LEVEL GAUGE
Oil level of hydraulic oil tank.
them, and apply liquid sealant on them. If the indicator is within
level marks, the oil quantity
6) Before assembling, remove rust preventives on is acceptable.
new parts.
7) Use special tools to fit bearings, bushing and oil 1.1.4 ELECTRICAL EQUIPMENT
seal.
8) Assemble parts matching to the marks.
9) After completion, check that there is no
(1) The disassembly of electrical equipment is not
omission of parts.
allowed.
(5) Installing hydraulic equipment
(2) Handle equipment with care so as not to drop it or
1) Confirm hydraulic oil and lubrication oil.
bump it.
2) Air release is required in the following cases ;
(3) Connector should be removed by unlocking while
1. Change of hydraulic oil holding the connector.
2. Replacement of parts on suction pipe side Never stress in tension to the caulked section by
3. Removing and attaching hydraulic pump pulling wire.
4. Removing and attaching swing motor (4) Check that connector is connected and locked
completely.
5. Removing and attaching travel motor
(5) Engine key off before removing and connecting
6. Removing and attaching hydraulic cylinder
connector.

1-4
 1. OUTLINE

(6) Engine key off before touching terminals of starter (2) Flexible hose (F hose)
and alternator. • Even if the connector and length of hose are the
(7) Remove battery grounding terminal before same, the parts differ according to the
beginning work close to battery and battery relay withstanding pressure. Use proper parts.
with tools. • Tighten it to the specified torque, and check that
(8) Wash machine with care so as not to splash water it is free from twist, over tension, interference,
on electrical equipment and connector. and oil leak.
(9) When water has entered in the waterproofed
1.1.6 WELD REPAIR
connector, the removing of water is not easy. So
(1) The weld repair should be carried out by qualified
check the removed waterproofed connector with
personnel in the specified procedure after
care to protect it from entry of water. If moisture
disconnecting the grounding cable of battery. If the
adheres on it, dry it completely before connecting.
grounding cable is not disconnected, the electrical
equipment may be damaged.
(2) Remove parts which may cause fire due to the
Battery fluid is dangerous. entry of spark beforehand.
The battery fluid is dilute sulfuric acid, and causes (3) Repair attachments which are damaged, giving
scald and loss of eyesight by adhering on eyes, particular attention to the plated section of piston
skin and clothes. When the fluid has adhered on rod to protect it from sparks, and don’t fail to cover
them, take an emergency measure immediately and the section with flame-proof clothes.
see a doctor for medical advice.
• When it has adhered on skin ; 1.1.7 ENVIRONMENTAL ISSUES
Wash with soap and water. (1) Engine should be started and operated in the place
• When it has got in eyes ; where air can be sufficiently ventilated.
Wash in water for 10 minutes or more (2) Waste disposal
immediately. The following parts follows the regulation.
• When it has spilled out in large quantity ; Waste oil, waste container and battery
Use sodium bicarbonate to neutralize, or wash (3) Precautions for handling hydraulic oil
away with water. Hydraulic oil may cause inflammation of eyes.
• When it was swallowed ; Wear goggles to protect eyes on handling it.
Drink milk or water. • When it has got in eyes ;
• When it has adhered on clothes ; Wash eyes with water until the stimulus is gone.
Wash it immediately. • When it was swallowed ;
Don’t force him to vomit it, but immediately
1.1.5 HYDRAULIC PARTS receive medical treatment.
• When it has adhered on skin ;
Wash with soap and water.
(4) Others
(1) O-ring For spare parts, grease and oil, use KOBELCO
• Check that O-ring is free from flaw and has genuine ones.
elasticity before fitting.
• Even if the size of O-ring is equal, the usage
differs, for example in dynamic and static
sections, the rubber hardness also differs
according to the pressure force, and also the
quality differs depending on the materials to be
seated. So, choose proper O-ring.
• Fit O-ring so as to be free from distortion and
bend.
• Floating seal should be put in pairs.

1-5
1. OUTLINE

1.2 INTERNATIONAL UNIT SYSTEM (4) Derived Units bearing Peculiar Designations
Introduction Table1-4
Although this manual uses the SI units system. Outline QUANTITY UNIT SYMBOL FORMULA
of SI units system is described here. Frequency hertz Hz 1Hz=1/s
Given hereinunder are an excerpt of the units that are Force newton N kg • m/s 2
related to this manual : Pressure and
pascal Pa N/m2
1. Etymology of SI Units Stress
English : International System of units Energy, Work
2. Construction of SI Unit System and Quantity of joule J N•m
heat
Base units Power watt W J/s
Table 1-1
Derived units Quantity of
of base units
coulomb C A•s
Supplemen electricity
SI units tary units Table 1-3
SI unit Table 1-2 Electric
system Derived units potential
Derived bearing peculiar
designations difference,
units volt V W/A
Table 1-4 Voltage, and
Electromotive
Prefixes of SI
(n-th power of 10, where n is an integer) force
Table 1- 5 Quantity of
static electricity
(1) Basic Units farad F C/V
and Electric
Table1-1 capacitance
Electric
QUANTITIES DESIGNATION SIGN ohm V/A
resistance
Length Meter m
celcius
Mass Kilogram kg Celcius
degree or C
° (t+273.15)K
Time Second s temperature
degree
Current Ampere A
Thermodynamic Kelvin K Illuminance lux lx l m/m2
temperature
(5) Prefixes of SI
Gram molecule Mol mol
Luminous intensity Candela cd Table1-5
PREFIX
(2) Supplementary Units POWER
DESIGNATION SIGN
Table1-2 Giga G 109
QUANTITIES DESIGNATION SIGN Mega M 106
Plain angle Radian rad Kilo k 103
Solid angle Steradian sr Hecto h 102
Deca da 10
(3) Derived Units of Basic Units
Deci d 10–1
Table1-3 Centi c 10–2
QUANTITIES DESIGNATION SIGN Milli m 10–3
Area Square meter m2 Micro µ 10–6
Volume Cubic meter m3 Nano n 10–9
Velocity Meter per second m/s Pico p 10–12
Acceleration Meter per second / second m/s2
Density Kilogram per cubic meter kg/m3

1-6
 1. OUTLINE

(6) Unit Conversion Table

QUANTITIES JIS SI REMARKS

Mass kg kg
Force kgf N 1kgf=9.807N
Torque kgf•m N•m 1kgf•m=9.807N•m
Pressure kgf/cm2 MPa 1kgf/cm2=0.098MPa
Motive power PS kW 1PS=0.7355kW
Revolution r.p.m min –1 1r.p.m=1min–1

1-7
1. OUTLINE

[MEMO]

1-8
 2

2. SPECIFICATIONS
TABLE OF CONTENTS

2.1 NAME OF COMPONENTS................................................................................................2-3

2.2 GENERAL DIMENSIONS ..................................................................................................2-4
2.2.1 SK200–8/SK210LC–8
[5.65m (18ft-6in) Boom+2.94m (9ft-8in) Standard Arm+0.80m3 (1.05cu•yd) Bucket Shoe] ....2-4
2.2.2 SK200–8/SK210LC–8
[5.65m (18ft-6in)+2.4m (7ft-10in) Short Arm+0.93m3 (1.22cu•yd) Bucket Shoe] ......2-4
2.2.3 SK200–8/SK210LC–8
[5.65m (18ft-6in) Boom+3.5m (11ft-6in) Long Arm+0.70m3 (0.92cu•yd) Bucket Shoe] ..........2-5
2.3 WEIGHT OF COMPONENTS............................................................................................2-6
2.4 TRANSPOTATION ............................................................................................................2-8
2.4.1 OVERALL DIMENSIONS OF MACHINE ON A TRAILER ........................................2-8
2.4.2 DIMENSIONS OF ATTACHMENT ...........................................................................2-9
2.5 SPECIFICATIONS AND PERFORMANCE .......................................................................2-11
2.5.1 SPEED AND CLIMBING CAPABILITY.....................................................................2-11
2.5.2 ENGINE ....................................................................................................................2-11
2.5.3 HYDRAULIC COMPONENTS ..................................................................................2-11
2.5.4 WEIGHT ...................................................................................................................2-11
2.6 TYPE OF CRAWLER.........................................................................................................2-12
2.7 TYPE OF BUCKET ............................................................................................................2-12
2.8 COMBINATIONS OF ATTACHMENT................................................................................2-13
2.9 ENGINE SPECIFICATIONS ..............................................................................................2-14
2.9.1 SPECIFICATIONS....................................................................................................2-14
2.9.2 ENGINE CHARACTERISTIC CURVE (HINO J05E-TG) ..........................................2-15

Book Code No. S5YN0223E01

2-1
2. SPECIFICATIONS

Issue Date of Issue Applicable Machines Remarks

SK200–8 : YN11-45001~ S5YN0223E01
First edition April, 2007 K
SK210LC–8 : YQ11-06001~ ASIA (HS Engine)

2-2
 2. SPECIFICATIONS

2.1 NAME OF COMPONENTS

ARM CYLINDER
ARM
BOOM

BOOM CYLINDER
BUCKET
CYLINDER
CAB

SLEWING BEARING

IDLER LINK
SLEWING MOTOR
SWIVEL
JOINT FUEL TANK

HYDRAULIC TANK
BUCKET LINK
CONTROL VALVE

GUARD
MUFFLER
HYDRAULIC
PUMP
BUCKET
MONITOR PANEL

SHOE AND TRACK LINK

FRONT IDLER

ENGINE
IDLER ADJUST

COUNTER WEIGHT
UPPER ROLLER

AIR CLEANER TRACK GUIDE

RADIATOR AND OIL COOLER
ROTALY MULTI CONTROL VALVE
(OPTION)

LOWER ROLLER BATTERY

TRAVEL MOTOR

2-3
2. SPECIFICATIONS

2.2 GENERAL DIMENSIONS

2.2.1 SK200–8/SK210LC–8 [5.65m (18ft-6in) Boom+2.94m (9ft-8in) Standard Arm+0.80m3 (1.05cu•yd)
Bucket Shoe]

Unit : mm(ft-in)

1315 (4'4")
43 (1.7")

2710 (8'11")
1395 (4'7")

R2
75
0
(9
')
9450 (31')

2750 (9')

3030 (9'11")
2980 (9'9")

*1060
(3'6")

450
(17.1")
600 (23.6")
4170 (13'8")
2800 (9'2")
4450 (14'7") [2990] (9'10")

Dimensions marked * do not include the height of the shoe lug.

[ ] include LC specifications.

2.2.2 SK200–8/SK210LC–8 [5.65m (18ft-6in)+2.4m (7ft-10in) Short Arm+0.93m3 (1.22cu•yd) Bucket Shoe]

9530 (31'3") Unit : mm(ft-in)

3980 (13'1")
2750 (9')
3160 (10'4")

*1060 (3'6")

4170 (13'8")
4450 (14'7")

2-4
 2. SPECIFICATIONS

2.2.3 SK200–8/SK210LC–8 [5.65m (18ft-6in) Boom+3.5m (11ft-6in) Long Arm+0.70m3 (0.92cu•yd) Bucket
Shoe]

9520 (31'3") Unit : mm(ft-in)

2750 (9')
3180 (10'5")

*1060 (3'6")
4170 (13'8")

4450 (14'7")

Dimensions marked * do not include the height of the shoe lug.

[ ] include LC specifications.

2-5
Suggest:
For more complete manuals. Please go to
the home page.

https://www.ebooklibonline.com

If the above button click is invalid. Please

download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
2. SPECIFICATIONS

2.3 WEIGHT OF COMPONENTS

Unit ; kg (lb)
Model
SK200 - 8 SK210LC - 8
Item
Machine complete 20,200 (44,500) 20,600 (45,400)
1. Upper frame assy (Assembly of following :) 9,500 (21,000) ←
1.1 Upper frame 1,770 (3,900) ←
1.2 Counter weight (Semi-weighted) 4,640 (10,230) ←
1.3 Cab 260 (570) ←
1.4 Engine *540 (1,190) ←
1.5 Hydraulic oil tank *150 (330) ←
1.6 Fuel tank *110 (240) ←
1.7 Slewing motor (including reduction unit) *210 (460) ←
1.8 Control valve *230 (510) ←
1.9 Boom cylinder *170 (375) × 2 ←
1.10 Pin (for mounting boom) 70 (150) ←
1.11 Pump *130 (290) ←
1.12 Radiator (including intercooler) *90 (200) ←
2. Lower frame assy (Assembly of following :) 6,730 (14,840) 7,130 (15,720)
2.1 Lower frame 2,260 (4,980) 2,420 (5,340)
2.2 Slewing bearing 250 (550) ←
2.3 Travel motor (including reduction unit) 260 (570) × 2 ←
2.4 Upper roller 20 (44) × 2 ←
2.5 Lower roller 30 (66) × 14 30 (66) × 16
2.6 Front idler 110 (240) × 2 ←
2.7 Idler adjuster 100 (220) × 2 ←
2.8 Sprocket 50 (110) × 2 ←
2.9 Swivel joint *30 (66) ←
2.10 Track link with 600mm (23.6in) shoes assy 1,260 (2,780) × 2 1,350 (2,980) × 2
Track link with 700mm (27.6in) shoes assy 1,470 (3,240) × 2 1,560 (3,440) × 2
Track link with 800mm (31.5in) shoes assy 1,600 (3,530) × 2 1,700 (3,750) × 2
2.10.1 Track link assy 510 (1,120) × 2 540 (1,190) × 2
3. Attachment (Assembly of following / STD :) 3,420 (7,540) ←
{5.65m (18ft-6in) Boom + 2.94m (9ft-8in) Arm + 0.80m (1cu•yd) Bucket}
3

3.1 Bucket assy (STD) 640 (1,410) ←

3.2 STD Arm assy (Assembly of following :) 1,050 (2,315) ←
3.2.1 STD Arm 660 (1,455) ←
3.2.2 Bucket cylinder *140 (310) ←
3.2.3 Idler link 20 (44) × 2 ←
3.2.4 Bucket link 90 (198) ←
3.2.5 Pin (2pcs. for mounting bucket cylinder / 2pcs. for mounting bucket) 100 (220) ←
3.3 Boom assy (Assembly of following :) 1,730 (3,815) ←
3.3.1 Boom 1,310 (2,890) ←
3.3.2 Arm cylinder *255 (560) ←
3.3.3 Pin (Mounting arm • Mounting arm cylinder) 80 (180) ←

2-6
 2. SPECIFICATIONS

Unit ; kg (lb)
Model
SK200 - 8 SK210LC - 8
Item
4. Lubricant and water (Assembly of following :) 550 (1,210) ←
4.1 Hydraulic oil 200 (440) ←
4.2 Engine oil 20 (44) ←
4.3 Fuel 310 (680) ←
4.4 Water 20 (44) ←

Marks * show dry weight.

2-7
https://www.ebooklibonline.com

Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.

https://www.ebooklibonline.com