StrucPro

According to ( ACI 318 14M , 19M - ASCE 07-16 ) V 2.0

Facebook Page https://www.facebook.com/profile.php?id=100094159105676

Youtube Channelhttps://www.youtube.com/@Engabdulrahmanelgohary/videos
Linkedin https://www.linkedin.com/in/eng-abdulrahman-elgohary-b48648159/

By Eng : Abdulrahman Elgohary

Senior Structural Engineer

INDEX
Gust Factor ASCE 07 -16
Raft Rigidity Check
δns-Rectangular Column
Alternative moment of inertia
Punching-Interior Column
Punching-Edge Column
Punching-Corner Column
One Way Shear ACI 318M-14
One Way Shear ACI 318M-19
Deep Shear ACI 318-19- Simplified CRSI
Deep Shear ACI 318-19 & Detailed CRSI
Crack Width Tension Pile
Crack Width Axial Tension + Moment
Settlement Of Single Pile
Flexure Member Design
Doubly RFT Section
Single RFT Section
Torsion Design
 Gust Factor Calculation Based On ASCE 2016
*Input Data
Time Period From ETABS 4.73 Sec

Exposure Type C

Width Of Structure, (B) 75 Meter

Length Of Structure, (L) 65 Meter
Height Of Structure, (H) 85 Meter
Damping Ratio, (β) 1.50%

Basic Wind Speed, (V) 30 m/s

*Output Data

Gf 0.91

C 0.2

zmin 4.57

ℓ 152.4

Iz` 0.152

έ 0.20

Lz` 211.11

Q 0.809

α` 0.11
b` 0.65

V`z` 23.15

n1 0.21

N1 1.93

Rn 0.09

ƞ For Rh 3.571 ƞ For RB 3.151 ƞ For RL 9.142

Rh 0.241 RB 0.267 RL 0.103

R 0.48

gr 3.80

gq 3.4
gv 3.4

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abderahman Elgouhry
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abderahman Elgouhry
 Raft Rigidity Check

Input Data
Raft Width (B) 80 m
Raft Thickness (H) 0.9 m
Max Spacing Between Columns (L) 8.1 m
Modulus Of Subgrade (K) 15000 Kn/m3
Modulus Of Elasticity (Ec) 29725 mpa

Output Data

Moment Of Inertia 486000000 Cm4

Lamda 0.0021347193 1/Cm ((K*B)/(4*Ec*I))^0.25
Le 468.44565973 Cm Le = 1/Lamda
1.75Le 819.77990454 Cm 8.197799 m
3Pi/2Le 2207.4981648 Cm 22.074982 m

The Raft Is Rigid

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
Calculate δns For Non - Sway Frames ACI 318-19M (Rectangular Column)
EI eff Calculation By Method 03- c

Ec- Modulus Of Elasticity0.043*(wc)^1.5*Sqrt(Fc`)

Cm-Correction Factor User Define

About Axis 2-2 Weak Axis

InPut

Compressive Strength Fc` 40.00 Mpa

Concrete Denisty wc 25.00 Kn/m3
Modulus Of Elasticity Ec 35000.00 Mpa

Ultimate Load Pu 25271.28 Kn

Sustained Load Factored DL 20665.68 Kn
Moment 1 M1 -0.464 Kn.m
Moment 2 M2 2.727 Kn.m
Correction Factor Cm 0.52 U.Less

Clear Height Lu 4.20 M

Unsupported Length
K 1.00 User Define
Factor
Moment Of Inertia
I22 0.700 U.Less
About Axix 2-2
Width Of Column B 30.00 Cm
Length Of Column L 330.00 Cm

Clear Cover Cc 3.0 Cm

Stirrups Diameter DIA 10 mm

RFT Details No Dia Area /mm2

Number Of Bars Along Axis 2-2 31 32 24919.04
Total Number Of Bars 62 32 49838.08
Ratio For RFT 5.03%

OutPut
Ec
Modulus Of Elasticity For Concrete ### Mpa
Moment Of Inertia For Concrete Ig ### Cm4
Moment Of Inertia For Steel Is 44059.26 Cm4
Cracked Moment Of Inertia I ### Cm4

Minimum Eccentricity emin 0.024 U.Less

Minimum Moment Mmin 606.51 Kn.m

Radius Of Gyration r 9.00 Cm

Klu/r 46.667 U.Less Ok < 100
34 ± 12(M1/M2) 31.957 U.Less Slender Column

βdns 0.818 U.Less

EI For Method 01- a 55543.07 Kn.m2

EI For Method 02- b 76248.14 Kn.m2

EI For Method 03- c 97200.38 Kn.m2

Crtitical Buckling Load / P###

C Kn OK (Pu < 0.75Pc)

Cm 0.532 U.Less

δns 1.37 U.Less OK < 1.4

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary

https://www.youtube.com/watch?v=MabvStBOSoo&t=677s Watch & Learn

Alternative moment of inertia for elastic anaylsis at factored loads ACI318-19M

InPut
Material Propert
FC` 65 Mpa ACI-19.2.1.1
Fy 500 Mpa ACI-20.2.2.4
Section Properti
C22 400 mm Column Width
C33 1200 mm Column Length
Cc 40 mm ACI-20.6.1.3.1
RFT Ratio 4.70% U.Less FROM ETABS
Loads
Pu 2633 Kn FROM ETABS
M22 1132 Kn.m FROM ETABS
M33 1854 Kn.m FROM ETABS

OutPut
Ast 22560 mm2
Ag 480000 mm2
Po 36553.56 Kn ACI-22.4.2.2

I22 0.350 ACI-6.6.3.1.1 (b)

I33 0.745 ACI-6.6.3.1.1 (b)

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
Moment values should be +ve value only
 Calculations For Two Way Shear As Per ( ACI 318-19M )

Input Data
Fc` 32 Mpa Size Effect Factor Neglect
Fyt 420 Mpa
H 400 mm
Cc 25 mm
ɸ 0.75 U.less
dp 10 mm
Spacing 90 mm
C1 300 mm
C2 600 mm
Vu 900 Kn
Mu-x 0 Kn.m
Mu-y 0 Kn.m

Output Data

d 375.00 mm
α 40 U.Less 22.6.5.3
β 2 U.Less Ratio Of Long To Short Side 22.6.5.2 - (ii)
b1 675 mm C1+d
b2 975 mm C2+d

≤)
bo 3300 mm 2*b1+2*b2

λs 1.00 U.Less λs = Sqrt( 2 / 1 + 0.004*d 1.0 22.5.5.1.3

ɸvc 1.400 Mpa 22.6.5.2 (a)

ɸvc 1.421 Mpa 22.6.5.2 (b)

ɸvc 2.322 Mpa 22.6.5.2 (c)

ɸvc Used 1.40 Mpa Least Of (a,b,c) 22.5.6.2

vuv 0.73 Mpa vuv = Vu / (bo*d)

d 150 mm 22.6.7.1 (a)

Shear RFT Ok
d 160 mm 22.6.7.1 (b)

ɸvc 0.72 Mpa 22.6.6.1 (a)

CAB-x 337.50 mm b1/2

CAB-y 487.50 mm b2/2

Jc/CAB-x ### mm3 (b1d(b1+3b2)+d3)/3

Jc/CAB-y ### mm3 (b1d(b1+3b2)+d3)/3

ɣf-x 0.64 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣf-y 0.56 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣv-x 0.36 U.Less 1-ɣf-x 8.4.4.2.2
ɣv-y 0.44 U.Less 1-ɣf-y 8.4.4.2.2

vu AB 0.73 Mpa R8.4.4.2.2

ɸvn max > vu
ɸvnmax 2.12 Mpa ɸvnmax = ɸ*0.5*Sqrt(F c`) 22.6.6.3 (a)
Section Ok
Punching
Ratio
0.52 U.Less vuAB / ɸvc

Bo 3327.56 mm Vu/ɸvc*d

a 457.537 mm ((Bo-(2*C1+2*C2))/4*sqrt(2))+0.5d

Av 5.680 mm2 ((vuAB-ɸvc)*bo*spacing)/ɸ*Fyt 22.6.7.2

No Of Legs 1.00 No Of Rows 6.00 Use 1 Legs T 10-6 Rows

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations For Two Way Shear As Per ( ACI 318-19M )

Input Data
Fc` 32 Mpa Size Effect Factor Consider
Fyt 420 Mpa
H 500 mm
Cc 30 mm
ɸ 0.75 U.less
dp 10 mm
Spacing 90 mm
C1 300 mm
C2 600 mm
Vu 1000 Kn
Mu-x 60 Kn.m
Mu-y 60 Kn.m

Output Data

d 470.00 mm
α 30 U.Less 22.6.5.3
β 2 U.Less Ratio Of Long To Short Side 22.6.5.2 - (ii)
b1 535 mm C1+0.5d
b2 1070 mm C2+d

≤)
bo 2140 mm 2*b1+b2

λs 0.83 U.Less λs = Sqrt( 2 / 1 + 0.004*d 1.0 22.5.5.1.3

ɸvc 1.17 Mpa 22.6.5.2 (a)

ɸvc 1.184 Mpa 22.6.5.2 (b)

ɸvc 2.535 Mpa 22.6.5.2 (c)

ɸvc Used 1.167 Mpa Least Of (a,b,c) 22.5.6.2

vuv 0.99 Mpa vuv = Vu / (bo*d)

d 150 mm 22.6.7.1 (a)

Shear RFT Ok
d 160 mm 22.6.7.1 (b)

ɸvc 0.60 Mpa 22.6.6.1 (a)

CAB-x 133.75 mm b12/2b1+b2

CAB-y 535.00 mm b2/2

Jc/CAB-x ### mm3 2b12d(b1+2b2)+d3(2*b1+b2)/6b1

Jc/CAB-y ### mm3 (b1d(b1+3b2)+d3)/3

ɣf-x 0.68 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣf-y 0.51 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣv-x 0.32 U.Less 1-ɣf-x 8.4.4.2.2
ɣv-y 0.49 U.Less 1-ɣf-y 8.4.4.2.2

vu AB 1.14 Mpa R8.4.4.2.2

ɸvn max > vu

ɸvnmax 2.12 Mpa ɸvnmax = ɸ*0.5*Sqrt(Fc`) 22.6.6.3 (a)
Section Ok
Punching
Ratio
0.97 U.Less vuAB / ɸvc

Bo 3539.96 mm Vu/ɸvc*d

a 542.584 mm ((Bo-(2*C1+2*C2))/4*sqrt(2))+0.5d

Av 327.808 mm2 ((vuAB-ɸvc)*bo*spacing)/ɸ*Fyt 22.6.7.2

No Of Legs 5.00 No Of Rows 7.00 Use 5 Legs T 10-7 Rows

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations For Two Way Shear As Per ( ACI 318-19M )

Input Data
Fc` 32 Mpa Size Effect Factor Neglect
Fyt 420 Mpa
H 500 mm
Cc 30 mm
ɸ 0.75 U.less
dp 10 mm
Spacing 90 mm
C1 300 mm
C2 600 mm
Vu 1000 Kn
Mu-x 60 Kn.m
Mu-y 60 Kn.m

Output Data

d 470.00 mm
α 20 U.Less 22.6.5.3
β 2 U.Less Ratio Of Long To Short Side 22.6.5.2 - (ii)
b1 535 mm C1+0.5d
b2 835 mm C2+0.5d

≤)
bo 1370 mm b1+b2

λs 1.00 U.Less λs = Sqrt( 2 / 1 + 0.004*d 1.0 22.5.5.1.3

ɸvc 1.40 Mpa 22.6.5.2 (a)

ɸvc 1.421 Mpa 22.6.5.2 (b)

ɸvc 3.137 Mpa 22.6.5.2 (c)

ɸvc Used 1.400 Mpa Least Of (a,b,c) 22.5.6.2

vuv 1.55 Mpa vuv = Vu / (bo*d)

d 150 mm 22.6.7.1 (a)

Shear RFT Ok
d 160 mm 22.6.7.1 (b)

ɸvc 0.72 Mpa 22.6.6.1 (a)

CAB-x 104.46 mm b12/2b1+b2

CAB-y 254.46 mm b12/2b1+b2

Jc/CAB-x ### mm 3 b1 d(b1+4b2)+d3(b1+b2)/6b1

2

Jc/CAB-y ### mm3 b12d(b1+4b2)+d3(b1+b2)/6b1

ɣf-x 0.65 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣf-y 0.55 U.Less 1 / (1+2/3*Sqrt(b1/b2)) 8.4.2.2.2
ɣv-x 0.35 U.Less 1-ɣf-x 8.4.4.2.2
ɣv-y 0.45 U.Less 1-ɣf-y 8.4.4.2.2

vu AB 1.78 Mpa R8.4.4.2.2

ɸvn max > vu

ɸvnmax 2.12 Mpa ɸvnmax = ɸ*0.5*Sqrt(Fc`) 22.6.6.3 (a)
Section Ok
Punching
Ratio
1.27 U.Less vuAB / ɸvc

Bo 2949.97 mm Vu/ɸvc*d

a 438.287 mm ((Bo-(2*C1+2*C2))/4*sqrt(2))+0.5d

Av 412.980 mm2 ((vuAB-ɸvc)*bo*spacing)/ɸ*Fyt 22.6.7.2

No Of Legs 6.00 No Of Rows 5.00 Use 6 Legs T 10-5 Rows

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations For One Way Shear As Per ( ACI 318-14M )

Input Data
Fc` 48 Mpa
Fyt 420 Mpa
B 1000 mm
H 1500 mm
Cc 75 mm
ɸ 0.75 U.less
Vu 5000 Kn

Output Data
ACI318 - Traditional One Way Shear At Distance (d) From (Column-Wall) Face

ɸVc ### Kn ɸVc = ɸ*0.17*Sqrt(Fc`)*b*d Need For Shear RFT

ɸVnmax ### Kn ɸVnmax = ɸ*0.83*Sqrt(Fc`)*b*d Ok ɸVnmax > Vu

Vs ### Kn Vs = (Vu/ɸ)-Vc Not OK Vs > 0.66*Sqrt(Fc`)*B*d
ɸVs ### Kn ɸVs = Vu-ɸVc
Spacing 200 mm Bar Dia 20 mm Use 6 Legs T 20-200
AvRequired ### mm 2
Av = (Spacing*Vs)/(Fyt*d)
Avmin ### mm 2
OK Av-min < Av-required

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
 Calculations For One Way Shear As Per ( ACI 318-19M )
Input Data
Fc` 40 Mpa Vc Case Table 22.5.5.1 Method a
Fyt 420 Mpa Size Effect Factor - λs Consider
B 1000 mm
H 280 mm
Cc 20 mm
ɸ 0.75 U.less
Nu 0 Kn Zero
7 16 Main
As
0 16 Extra
Vu 500 Kn

Output Data
ACI318 - Traditional One Way Shear At Distance (d) From (Column-Wall) Face

Vc 279.55 Kn Vc = (0.17*λ*SqrtFc`+Nu/6Ag)*bw*d

Vcmax 690.64 Kn Vcmax = 0.42*λ*Sqrt(Fc`)*b*d Ok Vcmax > Vc

Nu/6Ag 0.000 Clause 22.5.5.1.2 ACI318 (Ok Nu/6Ag < 0.05 Fc`)

λs 0.99 λs = Sqrt( 2 / 1 + 0.004*d ) Refer To Clause 13.2.6.2 For Foundation Design Only

ρw ### ρw = ( As / b*d )

ɸVc 209.66 Kn ɸVc = ɸ*(0.17*λ*SqrtFc`+Nu/6Ag)*bw*d Need For Shear RFT

ɸVnmax ### Kn ɸVnmax = ɸ*(Vc+0.66*Sqrt(Fc`)*b*d Ok ɸVnmax > Vu - Section Ok

Vs ### Kn Vs = (Vu/ɸ)-Vc OK Vs < 0.66*Sqrt(Fc`)*B*d
ɸVs ### Kn ɸVs = Vu-ɸVc

Spacing 150 mm Bar Dia 10 mm Use 7 Legs T 10-150

AvRequired ### mm2 Av = (Spacing*Vs)/(Fyt*d)

Avmin ### mm2 Avmin = (0.062*Sqrt(Fc`)*b/Fyt)*Spacing Av-min < Av-required

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations For One Way Shear As Per ( ACI 318-19M & CRSI )

Input Data
Fc` 56 Mpa Vc Case Table 22.5.5.1 Method a
Fyt 420 Mpa Size Effect Factor - λs Consider
B 7000 mm
w 2000 mm (w/d <1) - Check For CRSI Method
H 3500 mm
Cc 150 mm
ɸ 0.75 U.less
Nu 0 Kn Zero
20 40 Main
As
20 40 Extra
Vu 4000 Kn Shear Force @ Face Of Column / Wall

Output Data
CRSI- Simplified Special One Way Shear At Face of (Column-Wall) Face

Vc 29832.23 Kn Vc = (0.17*λ*SqrtFc`+Nu/6Ag)*bw*d

Vcmax 73703.17 Kn Vcmax = 0.42*λ*Sqrt(Fc`)*b*d Ok Vcmax > Vc

Nu/6Ag 0.000 Clause 22.5.5.1.2 ACI318M-19 (Ok Nu/6Ag < 0.05 Fc`)

λs 0.37 λs = Sqrt( 2 / 1 + 0.004*d ) Refer To Clause 13.2.6.2

ρw 0.214% ρw = ( As / b*d )

d 3350.00 d = H-Cc

K1 1.68 K1 =d/w
K2 2.01 K2 = 3.5-2.5*(w/d)
Enhancement 3.36 d/w*(3.5-2.5*(w/d)

ɸVc ### Kn ɸVc = ɸ*d/w*((3.5-2.5)*(w/d))*(0.17*λ*SqrtFc`+Nu/6Ag)*bw*d Ok ɸVc > Vu

ɸVcmax ### Kn ɸVcmax = ɸ*(0.83*Sqrt(Fc`)*b*d) Ok ɸVcmax > Vu - Section Ok

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations For One Way Shear As Per ( ACI 318-19M & CRSI )

Input Data
Fc` 48 Mpa Vc Case Table 22.5.5.1 Method a
Fyt 420 Mpa Size Effect Factor - λs Neglect
B 1000 mm
w 750 mm (w/d <1) - Check For CRSI Method
H 1500 mm
Cc 75 mm
ɸ 0.75 U.less
Nu 500 Kn Compression
7 25 Main
As
7 25 Extra
Vu 3000 Kn Shear Force @ Face Of Column / Wall
Mu 2000 Kn Moment @ Face Of Column/Wall

Output Data

CRSI- - Detailed Special One Way Shear At Face of (Column-Wall) Face

Vc 1757.52 Kn Vc = (0.17*λ*SqrtFc`+Nu/6Ag)*bw*d

Vcmax 4146.53 Kn Vcmax = 0.42*λ*Sqrt(Fc`)*b*d Ok Vcmax > Vc

Nu/6Ag 0.056 Clause 22.5.5.1.2 ACI318M-19 (Ok Nu/6Ag < 0.05 Fc`)

λs 1.00 λs = Sqrt( 2 / 1 + 0.004*d ) Refer To Clause 13.2.6.2

ρw 0.482% ρw = ( As / b*d )

d 1425.00 d = H-Cc

K1 0.47 K1 = (Mu/Vu*d) Ok 0.00 < K1 < 1.00

K2 2.33 K2 = 3.5-2.5*(Mu/Vu*d)
d/w 1.90
Enhancement 4.43 d/w*(3.5-2.5*(Mu/Vu*d)

ɸVc 5836.44 Kn ɸVc = ɸ*d/w*((3.5-2.5)*(Mu/Vu*d))*(0.17*λ*SqrtFc`+Nu/6Ag)*bw*d Ok ɸVc > Vu

ɸVcmax 6145.75 Kn ɸVcmax = ɸ*(0.83*Sqrt(Fc`)*b*d) Ok ɸVcmax > Vu - Section Ok

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Crack Width Calculations For Tension Pile (ACI 350-06/ACI 224.2R-92)

InPut
Tservise 1500 Kn Exposure Condition
Dpile 1000 mm wc-all 0.00 mm
User Define
FC` 40 Mpa wc-all 0.20 mm
Es 200000 Mpa Max Stress Of Tension Steel
dc 50 Normal Enviromental Exposure-One Way Member
mm
RFTDIA 32 mm
nt 16 U.less

OutPut
Spacing176.71 mm
As ### mm2
β 1.2 U.less
fs 129.52 Mpa OK fs < fs max
fs max 220.66 Mpa
Ec 29725 Mpa
n 6.73 U.less
A 9326.6 mm2

wcr 0.146 mm Not OK Wcr > Wcr all wcr = (140*fs*(A*dc)^1/3)*10 ^ -7

wcr 0.146 mm OK Wcr < Wcr all ACI 224.2R.92 Page 10 Equation 3.6

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
 Crack Width Calculations (ACI 350-06/ACI 224R-01)

Input Data
Material Properties :-
Concrete Compressive Strength FC` 50 Mpa Moduls Of Rupture Modifier 1.00

Concrete Compressive Strength Fy 500 Mpa

Section Properties :-
Section Width b 1000 mm Exposure Condition
Section Thickness h 2000 mm wc-all 0.00 mm
User Define
Cover To Center Of Closest Tension Bars dc 75 mm wc-all 0.20 mm
Cover To Center Of Tension Bars dcg 75 mm Max Stress Of Tension Steel
Important Note:- As Per ACI350R-01 When The Concrete Cover Exceed 50mm Use Only 50mm Normal Enviromental Exposure-One Way Member

Applied Service Moment :-

Applied Tension Axial Force (+ve) Ts 500 Kn

Applied Service Moment Ms 4000 Kn.m Method 01

Section Reinfocement :- wcr = 11*10^-6*β*Fs*(A*dc)^1/3 Method 01
No Dia Area/mm2 wcr = 2*(Fs/Es)*β*((dc)^2+(S/2)^2))^0.5Method 02
Main 8 25 3925
Tension RFT
Extra 16 25 7850
Spacing Between Bars S 150 mm

Compression RFT No Dia Area/mm2

Compression RFT Main 8 25 3925
Spacing Between Bars S 150 mm

Output Data

Concrete Modulus Of Elasticity Ec 33234.019 Mpa

Steel Modulus Of Elasticity Es 200000.00 Mpa
Modular Ratio n 6.018 U.Less
N.A Depth X 442.332 mm
Gross Moment Of Inertia Ig 666666666666.67 mm4
Cracked Moment Of Inertia Icr 187280416797.192 mm4
Moduls Of Rupture Fr 4.38 Mpa

Cracking Moment Mcr 2922.71 Kn.m Mcr < Ma Need Crack Width Calculations
Stress On Tension Steel Fs 212.61 Mpa Fs < Fs max - Safe
Max Stress On Tension Steel Fs-max 250.00 Mpa
Check For High Bond Bars Fs-bond 200.00 Mpa Fs > Fs bond - Unsafe
Depth Factor β 1.051 U.Less
Effective Tension Area A 6250.000 mm2

Allowable Crack Width wcr-all 0.20 mm

Actual Crack Width wcr-act 0.191 mm Safe Actual < Allowable

Actual Crack Width wcr-act 0.237 mm Unsafe Actual > Allowable

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry

https://www.youtube.com/watch?v=dwR6147ZPhg&t=2s Watch & Learn

 Elastic Settlement of Piles - Brajaa Das 8th Edition Chapter 09

InPut Data
Load Carried At The Pile Point Under Working 800 Kn
Load Condition Qwp

Load Carried By Frictional (skin) Resistance 300 Kn

Under Working Load Condition Qws

Concrete Compressive Strength Fc` 32 N/mm2

Pile Diameter D 0.5 m

Length Of Pile L 12 m

Factor ζ 0.67

Poisson Ratio µs 0.35

Modulus Of Elasticity Of Soil Es 38300 Kn/m2

Influence Factor Of Bearing Iwp 0.85

OutPut Data
Area Of Cross Section Of Pile Ap 0.20 m2

Modulus Of Elasticity Of The Pile

Ep 26,587,214.97 Kn/m2
Material
Point Load Per Unit Area At The Pile
qwp 4076.4 Kn/m2
Point

Perimeter Of The Pile P 1.57 m

Influence Factor Iws 3.71

Elastic Settlement Of Pile Se1 2.30 mm

Settlement Of Pile Caused By Bearing

Se2 39.69 mm
Load
Settlement Of Pile Caused By Friction
Se3 0.68 mm
Load

Total Settlement Se 42.67 mm

Total Load For Single Pile Qt 1100.00 Kn
Spring Constant K 25.78 Kn/mm

https://www.youtube.com/watch?v=Uw7eJryNA7s Watch & Learn

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Reinfocement For Flexure Members ACI-2019

Input Data

Mu 9500 Kn.m
b 1000 mm
h 5000 mm
Cs 150 mm
FC` 40 Mpa
fy 500 Mpa
ɸ 0.9 U.Less

Output Data
d 4850 mm
Rn 0.449
ρ 0.09%
AsReq 4381.92 mm2 Not Ok As < Asmin (Use Min)

Asmin 9000.00 mm 2

Main Mesh 8 40 10048 mm2

Extra Bars 8 40 10048 mm2

Asused 20096 mm2 Ok As used > As Required , Min

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Abdulrahman Elgohary
Facebook Eng Abdulrahman Elgohary
 Check for Doubly RFT Section ( ACI 318-19M )

Input Data
Mu 500 Kn.m
Fc` 32 Mpa
Fy 460 Mpa
b 250 mm
H 800 mm
Cc 30 mm
d` 30 mm

Number Dia
Tension RFT 6 16
As 1205.76 mm2

OutPut Data

ρ 0.626% U Less
As min 591.82 mm2
a 81.57 mm2
β1 0.85 U Less
C 95.96 mm2
Ԑt 0.021 U Less

ɸ 0.90 U Less

ɸMn Single 364.01 Kn.m Section Is UnSafe According To ACI Requirment Design As Doubly RFT Section

M2 191.54 Kn.m
Fs` 412.42 Mpa The Comp Steel Hasn't Yielded
As` Required 627.61 mm2

Comp RFT 4 16 Comp RFT OK

As` Actual 803.84 mm2

As2 720.70 mm2

Total As Required 1926.46 mm2

Tension RFT 6 25 Tension RFT OK

Total As Actual 2943.75 mm2

a 147.97 mm2
β1 0.85 U Less
C 174.09 mm2
Ԑt 0.010 U Less Tension Controlled
ɸ 0.90 U Less

ɸMn Doubly 1069.03 Kn.m Doubly Section Is Safe According To ACI Requirment

Cc 1006223.048
Cs 347901.952

Cc + Cs 1354125
1.00 OK Section Equilibrium
T 1354125

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Check for Single RFT Section ( ACI 318-19M )

Input Data
Mu 70 Kn.m
Fc` 55 Mpa
Fy 460 Mpa
b 300 mm
H 500 mm
Cc 30 mm

Number Dia
Tension RFT 5 16
As 1004.8 mm2

OutPut Data

ρ 0.713% U Less
As min 568.31 mm2
a 32.96 mm2
β1 0.65 U Less
C 50.70 mm2
Ԑt 0.0248 U Less Tension Controlled

ɸ 0.90 U Less

ɸMn 188.66 Kn.m Section Is Safe According To ACI Requirment

Cc 462208.00
1.00 OK Section Equilibrium
T 462208.00

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Calculations of Torsion & Shear ( ACI 318-19M )

Input Data

Tu 52 Kn.m Design Method Equilibrium Torsion

Vu 250 Kn Vc Case Table 22.5.5.1 Method b
b- Width 400 mm
H- Height 700 mm
Cc - Concrete Cover 56 mm
Nu 0

Fc` 28 Mpa
Fyt / Stirrups 420 Mpa
Fy / Longitudinal RFT 420 Mpa
Longitudinal RFT Dia 16 mm
T- Stirrups Dia 10 mm
No Of Legs 2.0 mm
Stirrups Spacing 100 mm
ɸ 0.75 U.Less

7 25
As - Tension Side
7 25

Output Data

ɸTth 11.74 Kn.m Stirrups 2 Legs T 10-100

ɸTcr 46.67 Kn.m Longitudinal RFT 5 16
vall 3.40 Mpa
vu 2.11 Mpa Section is ok

Detailed Calculations

d 644.0 mm
Xo 288.0 mm
Yo 588.0 mm
Acp 280000.0 mm2
Pcp 2200.0 mm
Acp2/Pcp ### mm
Aoh 169344.0 mm2
Ph 1752.0 mm

λs 0.75 U.Less
ρw 2.67% U.Less

Vc 268.8 Kn
Vc max 572.5 Kn Ok Vc Max > Vc
Nu/6Ag 0.00 U.Less
vall 3.40 Mpa
vu 2.11 Mpa
ɸVc 201.58 Kn
Vs 64.56 Kn

Design Of Stirrups

Av/s 0.24 mm2/mm

At/s 0.57 mm2/mm
Avt/s 1.39 mm2/mm
Av-min 0.33 mm2/mm
Spacing 110 mm
Max Spacing 219 mm ACI 318-19 / 9.7.6.3.3

Design Of Longitudinal RFT

Tn 69.33 Kn.m
Aℓ min 476.99 mm2
Aℓ 1004.63 mm2

Eng Abdulrahman Elgohary

Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry
 Eng Abdulrahman Elgohary
Tel 0525273709 / United Arab Emirates
Email [email protected]
Youtube Eng Abdulrahman Elgohary
Facebook Eng Abdelrahman Elgouhry

If you choose the design method = compatibility torsion you should overwrite Tu = ɸTcr