Corrugate

COMMERCIAL VERTICAL CLADDING

DETAIL LIST Revision Date
F 00 / 18 COVER SHEET
F 01 / 18 PARAPET AND BALUSTRADE CAPPING 1.0 JAN 2023
F 02 / 18 SCUPPER W/ RAINWATER HEAD 1.0 JAN 2023
F 03 / 18 SOFFIT 1.0 JAN 2023
F 04 / 18 WINDOW HEAD 1.0 JAN 2023
F 05 / 18 WINDOW SILL 1.0 JAN 2023
F 06 / 18 WINDOW JAMB 1.0 JAN 2023
F 07 / 18 METERBOX HEAD 1.0 JAN 2023
F 08 / 18 METERBOX SILL 1.0 JAN 2023
F 09 / 18 METERBOX JAMB 1.0 JAN 2023
F 10 / 18 INTERNAL CORNER 1.0 JAN 2023
F 11 / 18 EXTERNAL CORNER 1.0 JAN 2023
F 12 / 18 SOAKER FLASHING 1.0 JAN 2023
F 13 / 18 CHANGE IN CLADDING 1.0 JAN 2023
F 14 / 18 CLADDING ABUTMENT 1.0 JAN 2023
F 15 / 18 BOTTOM OF CLADDING (FLUSH) 1.0 JAN 2023
F 16 / 18 BOTTOM OF CLADDING (RECESSED) 1.0 JAN 2023
F 17 / 18 3D WINDOW FLASHINGS 1.0 JAN 2023
F 18 / 18 3D RAINWATER HEAD 1.0 JAN 2023

Metalcraft
Roofing
CVCG www.metalcraftgroup.co.nz
AS PER E2/ASI
SITUATION 1 SITUATION 2 SITUATION 3

1. LOW, MEDIUM, HIGH W IND ZONES, 1. ALL ROOF PITCHES IN VERY HIGH 1. FOR ALL ROOF PITCHES IN EXTRA
W HERE ROOF PITCH ≥ 10° W IND ZONE HIGH W IND ZONES
2. LOW, MEDIUM, HIGH W IND ZONES
W HERE ROOF PITCH ≤ 10°

Z MIN. 50mm MIN. 70mm MIN. 90mm

PRE-FINISHED PARAPET CAP FLASHING
NO FIXINGS ON TOP OF FLASHING

AS PER MRM CODE OF PRACTICE

SEPARATE METAL CAPPING AND
CATEGORY A CATEGORY B
TIMBER WITH DPC, SHOWN DASHED
1. NORMAL EXPOSURE 1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.
2. ROOF PITCH >10° 2. ROOF PITCH <10°

Z MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH) CONTINUOUS TIMBER PACKING
MIN. 75mm (VERTICALLY DOWN FACE - PROFILED) MIN. 100mm (VERTICALLY DOWN FACE - PROFILED)

MIN. 5.00°
STOPENDS TO WALL CLADDING

20

15

5 GAP

Z
Z

ALTERNATIVE OPTION
BIRDS BEAK EDGE
METALCRAFT MSS PURLIN
BY ENGINEER PRE-FINISHED SEALED POP RIVET OR
HEMMED EDGE PRE-FINISHED 8g WAFER-TEK SCREW

COMPRESSIBLE FOAM SEAL WHEN

REQUIRED.
20mm HORIZONTAL CAVITY
BATTEN
PERMEABLE WALL UNDERLAY,
METALCRAFT CORRUGATE SHOWN DASHED
VERTICAL CLADDING
PARAPET AND BALUSTRADE CAPPING
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 01 / 18
 PERMEABLE WALL
METALCRAFT CORRUGATE UNDERLAY, SHOWN
VERTICAL CLADDING DASHED
SEPARATE BATTEN AND
PRE FINISHED SELF TAPPING CLADDING AS REQUIRED
SCREW WITH NEOPRENE WITH DPC
WASHER
20mm HORIZONTAL CAVITY
CONTINUOUS MEMBRANE BATTEN
DRESSED THROUGH BASE AND
UP SIDES OF OPENING WITH WALL FRAMING
UPPER EDGES SEALED AGAINST
CLADDING. RETURN ALONG BACK 8g WAFER-TEK SCREW
OF RAINWATER HEAD

RETURN MEMBRANE INTO

RAINWATER HEAD

RAINWATER HEAD

CAVITY CLOSER

SCUPPER
TRUE ROOF LINE BEHIND

50
RAINWATER HEAD
OVERFLOW BELOW
OPENING LEVEL,1.5 x

25
DOWNPIPE DIAMETER

MEMBRANE ON ROOF
RETURN SUBSTRATE
MEMBRANE AT END
OF LIP
PRE FINISHED SELF
TAPPING SCREW WITH
METALCRAFT CORRUGATE
NEOPRENE WASHER
VERTICAL CLADDING

SCUPPER W/ RAINWATER HEAD

Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 02 / 18
PRE-FINISHED FLAT HEAD WAFER-TEK SCREW PRE-FINISHED
FOR FLASHING FIXED INTO SUBSTRATE SOFFIT FLASHING

COMPRESSIBLE FOAM SEAL WHEN REQUIRED.

METALCRAFT
MSS PURLIN BY
STOPENDS TO WALL CLADDING ENGINEER

METALCRAFT MSS PURLIN BY

ENGINEER
BARGE BOARD

SOFFIT LINING

COVER CLADDING
(MIN. 35mm)
INTERNAL CEILING LINING

60mm
SEPARATE BATTEN AND
FLASHING WITH DPC AS
REQUIRED

MIN. 50mm
PRE-FINISHED SELF
DRILLING/TAPPING SCREW
WITH NEOPRENE WASHER
METALCRAFT CORRUGATE
VERTICAL CLADDING
PRE-FINISHED SEALED POP
RIVET OR PRE-FINISHED 8g
WAFER-TEK SCREW 20mm HORIZONTAL CAVITY
BATTEN

METALCRAFT MSS PURLIN

BY ENGINEER
PERMEABLE WALL UNDERLAY,
SHOWN DASHED
INTERNAL WALL LINING
SOFFIT
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 03 / 18
 METALCRAFT CORRUGATE VERTICAL
CLADDING
EXTRA PERMEABLE WALL UNDERLAY
INTERNAL WALL LINING OVER WINDOW HEAD FLASHING,
SHOWN DASHED

PRE-FINISHED SELF DRILLING / SEPARATE BATTEN AND CLADDING

TAPPING SCREW WITH NEOPRENE WITH DPC AS REQUIRED
WASHER

20mm HORIZONTAL CAVITY BATTEN

MIN. 75mm WITHOUT HEM EDGE

CAVITY CLOSER AS
REQUIRED TO NZBC

MIN. 50mm COVER

DRIP EDGE TO CLADDING
PRE-FINISHED FLAT HEAD WAFER-

MIN. 15mm GAP

TEK SCREW FOR FLASHING

GAP
METALCRAFT MSS PURLINS BY
ENGINEER

5mm
PERMEABLE WALL UNDERLAY
DRESSED INTO OPENING WITH
FLEXIBLE FLASHING TAPE INSTALLED

10mm GAP
OVER WRAP TO CORNERS AT HEAD

AIRSEAL ON BACKING ROD TO

RUN CONTINUOUSLY AROUND
HEAD, SILL AND JAMB
PRE-FINISHED WINDOW HEAD
FLASHING WITH 15° FALL
TEMPORARY PACKER IF REQUIRED,
REMOVED AFTER FIXING
STOPENDS TO HEAD FLASHING,
SHOWN DASHED
WINDOW HEAD LINER DOUBLE GLAZING WINDOW JOINERY

LINE OF WINDOW JAMB LINE OF JAMB FLASHING BEHIND

LINER BEHIND

WINDOW HEAD
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 04 / 18
LINE OF WINDOW JAMB LINE OF JAMB FLASHING BEHIND
LINER BEHIND

DOUBLE GLAZING WINDOW JOINERY

MIN. 8mm PACKER

WINDOW SILL SUPPORT BAR

FLEXIBLE FLASHING TAPE OVER
PERMEABLE WALL UNDERLAY FOR
FULL WIDTH/DEPTH SILL PRE-FINISHED WINDOW SILL
FLASHING

AIRSEAL ON BACKING ROD TO STOPENDS TO SILL FLASHING,

RUN CONTINUOUSLY AROUND SHOWN DASHED
HEAD, SILL AND JAMB COMPRESSIBLE FOAM SEAL WHEN
REQUIRED.
WINDOW SILL LINER

MIN. 8mm COVER

INTERNAL WALL LINING

5mm GAP
METALCRAFT MSS PURLIN BY
ENGINEER

COVER CLADDING
70mm (MIN. 30mm)
SEPARATE BATTEN AND FLASHING
WITH DPC AS REQUIRED

PRE-FINISHED SELF DRILLING/TAPPING

SCREW WITH NEOPRENE WASHER

PRE-FINISHED SEALED POP RIVET OR

PRE-FINISHED 8g WAFER-TEK SCREW
20mm HORIZONTAL CAVITY BATTEN

PERMEABLE WALL UNDERLAY, METALCRAFT CORRUGATE VERTICAL

SHOWN DASHED CLADDING

WINDOW SILL
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 05 / 18
 INTERNAL WALL LINING
ALTERNATIVE OPTION

LINE OF WINDOW SILL LINER

BELOW
5mm
AIRSEAL ON BACKING ROD TO
RUN CONTINUOUSLY AROUND
HEAD, SILL AND JAMB

PERMEABLE WALL UNDERLAY,

DIMENSION TO SUIT SHOWN DASHED
SUGGEST MIN. 2 CORRUGATIONS
WINDOW JAMB LINER

METALCRAFT MSS PURLIN BY

PRE-FINISHED SELF DRILLING/TAPPING
ENGINEER
SCREW WITH NEOPRENE WASHER
TIMBER PACKER
PRE-FINISHED FLAT HEAD WAFER-TEK
SCREW FOR FLASHING FLEXIBLE FLASHING TAPE OVER
PERMEABLE WALL UNDERLAY
SEPARATE BATTEN AND FLASHING FOR FULL WIDTH/DEPTH SILL
WITH DPC AS REQUIRED
LINE OF HEAD FLASHING ABOVE
20mm HORIZONTAL
CAVITY BATTEN

PRE-FINISHED SECONDARY
FLASHING IF REQURIED
5mm GAP

LINE OF SILL FLASHING BELOW

METALCRAFT CORRUGATE
VERTICAL CLADDING
MIN. 10mm COVER
PRE-FINISHED SEALED POP RIVET OR PRE- LINE OF HEAD FLASHING ABOVE
FINISHED 8g WAFER-TEK SCREW
MIN. 2 CORRUGATIONS 5mm GAP

PRE-FINISHED WINDOW JAMB FLASHING DOUBLE GLAZING WINDOW

JOINERY

WINDOW JAMB
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 06 / 18
 METALCRAFT CORRUGATE VERTICAL
INTERNAL WALL LINING
CLADDING
SEPARATE BATTEN AND CLADDING AS
EXTRA PERMEABLE WALL UNDERLAY REQUIRED WITH DPC
OVER WINDOW HEAD FLASHING
SHOWN DASHED 20mm HORIZONTAL CAVITY BATTEN

PRE-FINISHED HEAD FLASHING

WITH 15° FALL
PRE-FINISHED SELF DRILLING / TAPPING
SCREW WITH NEOPRENE WASHER

CAVITY CLOSER AS REQUIRED TO NZBC

MIN. 75mm WITHOUT HEM EDGE

PRE-FINISHED FLAT HEAD WAFER-TEK

MIN. 50mm COVER

SCREW FOR FLASHING

DRIP EDGE TO CLADDING

MIN. 15mm GAP
METALCRAFT MSS PURLINS BY
ENGINEER

GAP
PERMEABLE WALL UNDERLAY
DRESSED INTO OPENING WITH

5mm
FLEXIBLE FLASHING TAPE INSTALLED
OVER WRAP TO CORNERS AT HEAD

AIRSEAL ON BACKING ROD TO RUN

CONTINUOUSLY AROUND HEAD, SILL
AND JAMB

TEMPORARY PACKER IF PRE-FINISHED SELF DRILLING/TAPPING

REQUIRED, REMOVED AFTER SCREW WITH NEOPRENE WASHER
FIXING
PRE-FINISHED 'U' BRACKET FIXED TO
METER BOX METERBOX BEFORE INSTALLATION

METAL ANGLE TO BE CONTINUOUS STOPENDS TO HEAD FLASHING

AROUND METER BOX SEALED.
LINE OF JAMB FLASHING BEHIND

METERBOX HEAD
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 07 / 18
INTERNAL WALL LINING

LINE OF JAMB FLASHING BEHIND

METER BOX

PRE-FINISHED FLASHING FIXED TO

METAL ANGLE
METAL ANGLE TO BE CONTINUOUS
AROUND METER BOX SEALED.
STOPENDS TO SILL FLASHING, SHOWN
MIN. 8mm PACKER DASHED

AIRSEAL ON BACKING ROD TO

RUN CONTINUOUSLY AROUND
HEAD, SILL AND JAMB
COMPRESSIBLE FOAM SEAL SEALED
METALCRAFT MSS PURLIN BY WHEN REQUIRED.
ENGINEER

FLEXIBLE FLASHING TAPE OVER

PERMEABLE WALL UNDERLAY FOR
FULL WIDTH/DEPTH SILL

COVER CLADDING
60mm (MIN. 35mm)
STOPENDS TO WALL CLADDING

SEPARATE BATTEN AND FLASHING AS

REQUIRED WITH DPC

20mm HORIZONTAL CAVITY BATTEN

PERMEABLE WALL UNDERLAY, PRE-FINISHED SEALED POP RIVET OR

SHOWN DASHED PRE-FINISHED 8g WAFER-TEK SCREW

PRE-FINISHED SELF DRILLING / TAPPING

SCREW WITH NEOPRENE WASHER METALCRAFT CORRUGATE VERTICAL
CLADDING

METERBOX SILL
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 08 / 18
INTERNAL WALL LINING METALCRAFT MSS PURLIN
BY ENGINEER

AIRSEAL ON BACKING ROD TO

RUN CONTINUOUSLY AROUND
FLEXIBLE FLASHING TAPE OVER HEAD, SILL AND JAMB
PERMEABLE WALL UNDERLAY FOR
FULL WIDTH/DEPTH SILL METER BOX

PERMEABLE WALL UNDERLAY,

SHOWN DASHED

PRE-FINISHED FLAT HEAD WAFER-

TEK SCREW FOR FLASHING
TIMBER PACKER

PRE-FINISHED SELF DRILLING/TAPPING

SCREW WITH NEOPRENE WASHER LINE OF HEAD FLASHING ABOVE

20mm HORIZONTAL METAL ANGLE TO BE CONTINUOUS

CAVITY BATTEN AROUND METER BOX SEALED.

SEPARATE BATTEN AND FLASHING

WITH DPC AS REQUIRED LINE OF SILL FLASHING BELOW

METALCRAFT CORRUGATE
LINE OF HEAD FLASHING ABOVE
VERTICAL CLADDING

WEATHERSEAL ON BACKING ROD

DIMENSION TO SUIT
PRE-FINISHED SEALED POP RIVET OR
PRE-FINISHED 8g WAFER-TEK SCREW SUGGEST MIN. 50mm
PRE-FINISHED JAMB FLASHING
FIXED TO METERBOX BEFORE
INSTALLATION

METERBOX JAMB
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 09 / 18
 MIN. 2 CORRUGATIONS

ALTERNATIVE OPTION
METALCRAFT
CORRUGATE VERTICAL
CLADDING
DIMENSION TO SUIT
20mm HORIZONTAL CAVITY
SUGGEST MIN. 100mm BATTEN

PRE-FINISHED INTERNAL
CORNER FLASHING

PERMEABLE WALL
UNDERLAY, SHOWN
DASHED
PRE-FINISHED FLAT
HEAD WAFER-TEK
SCREW WITH EPDM
WASHER
SEPARATE BATTEN AND
FLASHING WITH DPC AS
REQUIRED
5mm GAP

PRE-FINISHED SECONDARY
FLASHING

PRE-FINISHED SEALED POP RIVET OR

METALCRAFT MSS PURLIN
PRE-FINISHED 8g WAFER-TEK SCREW
BY ENGINEER

PRE-FINISHED FLAT HEAD

WAFER-TEK FOR FLASHING
STRUCTURAL COLUMN BY
ENGINEER
INTERNAL CORNER
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 10 / 18
20mm HORIZONTAL
CAVITY BATTEN

MIN. 2 CORRUGATIONS

METALCRAFT MSS PURLIN

BY ENGINEER

PRE-FINISHED EXTERNAL
CORNER FLASHING

5m
m
GA
SEPARATE BATTEN AND

P
FLASHING WITH DPC AS
REQUIRED

PRE-FINISHED
SECONDARY FLASHING

ALTERNATIVE OPTION PRE-FINISHED FLAT HEAD

WAFER-TEK SCREW FOR
DIMENSION TO SUIT FLASHING
SUGGEST MIN. 100mm

PRE-FINISHED FLAT HEAD

WAFER-TEK SCREW WITH
EPDM WASHER
5mm GAP

PRE-FINISHED SEALED
POP RIVET OR PRE-
5mm GAP FINISHED 8g WAFER-TEK
10
mm
SCREW
GA
P
PERMEABLE WALL
UNDERLAY, SHOWN
DASHED

METALCRAFT CORRUGATE
VERTICAL CLADDING

STRUCTURAL COLUMN BY ENG

EXTERNAL CORNER
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 11 / 18
PRE-FINISHED SOAKER METALCRAFT
FLASHING TO LINE UP WITH SOAKER FLASHING ONLY REQUIRED CORRUGATE VERTICAL
WINDOW JAMB ABOVE TO LINE UP WITH WINDOW JAMB CLADDING
ABOVE.
REFER TO MRM CODE OF PRACTICE
VERSION 3.0 /2022 FOR REQUIRMENT.

SEPARATE BATTEN AND

FLASHING WITH DPC AS
20mm HORIZONTAL CAVITY REQUIRED
BATTEN

METALCRAFT MSS PURLIN PERMEABLE WALL

BY ENGINEER UNDERLAY, SHOWN
DASHED

INTERNAL WALL LINING METALCRAFT MSS PURLIN BY

ENGINEER

SOAKER FLASHING
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 12 / 18
 PRE FINISHED MATERIAL
FLASHING

SEPARATE BATTEN AND

20mm HORIZONTAL CAVITY FLASHING WITH DPC AS
BATTENS REQUIRED
MIN. 2 CORRUGATIONS
FIBRE CEMENT BOARD
METALCRAFT CORRUGATE VERTICAL OR OTHER SIMILAR
CLADDING CLADDING

5mm GAP

PERMEABLE WALL
UNDERLAY, SHOWN DASHED

PRE FINISHED SELF

TAPPING SCREW WITH
NEOPRENE WASHER
CHANGE IN CLADDING
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 13 / 18
 CONCRETE WALL BY
OTHERS

PRE-FINISHED
ALUMINIUM FLASHING

PRE-FINISHED POP RIVET

BEDDED IN SILICONE
METALCRAFT CORRUGATE
VERTICAL CLADDING
MASTIC BEAD ON
BACKING ROD
20mm HORIZONTAL
CAVITY BATTENS RAWLPLUG

PRE FINISHED
ALUMINIUM FLASHING

PRE FINISHED
SECONDARY FLASHING

FLEXIBLE FLASHING TAPE

SEPARATE BATTEN AND

FLASHING WITH DPC AS
REQUIRED

PERMEABLE WALL
UNDERLAY, SHOWN
DASHED

PRE FINISHED SELF 8g WAFER TEK

TAPPING SCREW WITH SCREW
NEOPRENE WASHER
DPC

WALL FRAMING

CLADDING ABUTMENT
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 14 / 18
PERMEABLE WALL UNDERLAY,
SHOWN DASHED
METALCRAFT CORRUGATE
VERTICAL CLADDING
INTERNAL WALL LINING

20mm HORIZONTAL CAVITY

PRE-FINISHED SELF DRILLING / BATTEN
TAPPING SCREW WITH NEOPRENE
WASHER
PRE-FINISHED FLAT HEAD WAFER-
METALCRAFT MSS PURLIN BY TEK SCREW FOR FLASHING
ENGINEER

PRE-PRIMED SKIRTING PRE-FINISHED NON-PERFORATED

CLOSURE FLASHING WITH 10° FALL
DPC

CONCRETE SLAB CAVITY CLOSER AS REQUIRED TO

NZBC

MIN. 50mm LAP

DRIP EDGE TO CLADDING
MIN. 15mm GAP
GAP
GAP
ATION
GROUND CLEARANCE IS NECESSARY BETW EEN BOTTOM OF

3 - 5mm
PROFILED METAL CLADDING AND LARGE FLAT SURFACES

VENTIL
APPLICATION
25mm CLEARANCE AT GARAGE DOOR
SHELTERED AREAS OR CLADDING ABUTTING A
35mm DECK
75mm UNLINED BUILDINGS
LINED BUILDINGS AND DWELLINGS. STONE CHIP
100mm
GROUND SURFACE
150mm KEPT LAWN GROUND SURFACE
175mm PASTURE GROUND SURFACE

BOTTOM OF CLADDING (FLUSH)

Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 15 / 18
INTERNAL WALL LINING
METALCRAFT CORRUGATE
VERTICAL CLADDING

PERMEABLE WALL UNDERLAY OVER

FLASHING, SHOWN DASHED
20mm HORIZONTAL CAVITY
BATTEN
CAVITY CLOSER AS REQUIRED TO
NZBC
PRE-FINISHED SELF DRILLING / TAPPING
SCREW WITH NEOPRENE WASHER
PRE-FINISHED NON-PERFORATED
CLOSURE FLASHING WITH 10° FALL

PRE-FINISHED FLAT HEAD WAFER- 20

TEK SCREW FOR FLASHING

MIN. 75mm COVER

DPC
15

PRE-PRIMED SKIRTING 5 GAP

GAP
CONCRETE SLAB

ION
ALTERNATIVE OPTION

ILAT
BIRDS BEAK EDGE

ENT

MIN. 50mm LAP

mm V
3-5
GROUND CLEARANCE IS NECESSARY BETW EEN BOTTOM OF
PROFILED METAL CLADDING AND LARGE FLAT SURFACES

APPLICATION
25mm CLEARANCE AT GARAGE DOOR
SHELTERED AREAS OR CLADDING ABUTTING A
35mm DECK
75mm UNLINED BUILDINGS
LINED BUILDINGS AND DWELLINGS. STONE CHIP
100mm
GROUND SURFACE
150mm KEPT LAWN GROUND SURFACE
175mm PASTURE GROUND SURFACE

BOTTOM OF CLADDING (RECESSED)

Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale 1:2 Sheet F 16 / 18
 OR
METALCRAF
T
CORRUGAT
E VERTICAL
CLADDING
SECONDARY
DEFENCE SOAKERS
HEAD FLASHING WHEN REQUIRED

ALUMINIUM
WINDOW
JOINERY

JAMB FLASHING

INDICATIVE

SILL FLASHING

3D WINDOW FLASHINGS
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale Sheet F 17 / 18
 METALCRAFT CORRUGATE VERTICAL
N CLADDING
MI
mm G
0 IN
20 PEN
O
N
MI E
0 mmR SID
5 HE
EIT

LIP OF DISCHARGE AT LOWEST

POINT OF ROOF

75 mm MIN
OPENING

OVERFLOW BELOW OPENING LEVEL, 1.

CROSS-SECTION AREA OF DOWNPIPE

DOWNPIPE

3D RAINWATER HEAD
Metalcraft
Roofing
DISCLAIMER:
All details are to be used for indicative purposes only and the designer should consult both the MRM
code of practice version 3.0 / 2022, E2 and all other relevant building codes
Details of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is
Corrugate Rev. 1.0 COMMERCIAL VERTICAL CLADDING

www.metalcraftgroup.co.nz
the responsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed
as a single line for simplicity and is indicative only. Building paper type and method of installation should
comply with underlay manufacturers recommendations and NZBC regulations.
Reference CVCG Date JAN 2023 Scale Sheet F 18 / 18