Extended Product Overview

HUMIDUR®
ME E FP TC
ME ME Brush FP Single/FP Hydro FP Plural FP Brush FP Brush Extreme FP QR
Anti-corrosion
Duties

Anti-fouling
Topcoat
Surface tolerant
Steel Only esthetic purposes
Other metals Only esthetic purposes
Substrate

Concrete
Humidur coatings
Other coatings
Glass Reinforced Plastic (GRP) N/A N/A N/A N/A N/A N/A N/A N/A N/A
Fibre Reinforced Plastic (FRP) N/A N/A N/A N/A N/A N/A N/A N/A N/A
100% solids / 0% VOC
Compo-

Solvent-free
sition

2K-polyamine epoxy
2K-epoxy siloxane
Brush / roller/ spatula
Dispensing Gun
Appli-
cation

Single component spray (heated hoses)

Plural component spray (heated hoses)
Colour Any RAL - 25 standard shades Any RAL - 25 standard shades Any RAL 25 standard shades Any RAL - 25 standard shades Any RAL - 25 standard shades Any RAL - 25 standard shades Refer to TDS Refer to TDS Any RAL - 25 standard shades
Density at 23°C ± 1.36 g/cm³ ± 1.27 g/cm³ ± 1.38 g/cm³ ± 1.36 g/cm³ ± 1.39 g/cm³ ± 1.13 g/cm³ ± 1.15 g/cm³ ± 1.21 g/cm3 ± 1.23 g/cm³
Physical Properties

Viscosity 6.0 ± 1 Pas 4.5 ± 1 Pas 10.5 ± 1 Pas 25 ± 1 Pas 45 ± 1 Pas 8.8 ± 1 Pas N/A N/A 3 ± 1 Pas
Adhesion value > 8 MPa > 8 MPa > 8 MPa > 8 MPa > 8 MPa > 8 MPa > 8 Mpa > 5 MPa > 5 MPa
Hardness (Shore D) > 74 > 74 > 74 > 74 > 74 > 74 > 74 > 74 > 80
Flash point > 100°C > 100°C > 120°C > 100°C > 100°C > 100°C > 100°C > 100°C > 90°C
Touch dry at 20°C 4 hours 4 hours 2 hours 3 hours 3 hours 3 hours 4 hours 5 hours 4 hours
Full cure at 20°C 48 hours 48 hours 12 hours 24 hours 24 hours 24 hours 24 hours 36 hours 3 days
One coat system Yes Yes Yes Yes Yes Yes Yes Yes Only esthetic purposes
Standard packaging 22 kg 5 kg 22 kg 18 kg 22 kg 5 kg 5 kg 180 ml 4 kg
Pot life (at 23°C) 45 min 45 min 10 min 25 min 25 min 25 min 25 min N/A 2 hours
Technical Properties

Shelf life at 25°C 12 months 12 months 24 months 24 months 24 months 24 months 24 months 24 months 12 months
Mixing ratio by weight 4.4:1 3.7:1 4.03:1 5.0:1 4.0:1 3.7:1 2.6:1 2.63:1 7.6:1
Mixing ratio by volume 3.2:1 2.9:1 2.9:1 3.8:1 2.9:1 3.475:1 2.4:1 2:1 5.9:1
Film thickness min./ max. 300 µm / 1000µm 200 µm / 300 µm 300 µm / 2000 µm 400 µm / 800 µm 400 µm / 2000 µm 200 µm / 400 µm 200 µm / 200 µm 200 µm / 400 µm 60 µm / 100 µm
Covering capacity (min. thickness) 0.41 kg/m² 0.25 kg/m² 0.42 kg/m² 0.54 kg/m² 0.55 kg/m² 0.23 kg/m² 0.23 kg/m² 0.48 kg/m² 0.074 kg/m²
Min. overcoating time wet-on-wet wet-on-wet wet-on-wet wet-on-wet wet-on-wet wet-on-wet wet-on-wet wet-on-wet 4 hours
Max. overcoating time unlimited unlimited unlimited unlimited unlimited unlimited unlimited Roughen the surface 48 hours
Cleaning of material HumiClean HumiClean HumiClean HumiClean HumiClean HumiClean HumiClean HumiClean HumiClean
Cleanliness St 2-3 - ISO 8501 St 2-3 - ISO 8501 St 2-3 - ISO 8501 St 2-3 - ISO 8501 St 2-3 - ISO 8501 St 2-3 - ISO 8501 St 2-3 - ISO 8502 St 2-3 - ISO 8503 N/A
Roughness Original profile Original profile Original profile Original profile Original profile Original profile Original profile Original profile N/A
Grind disk Grind disk Grind disk Grind disk Grind disk Grind disk Grind disk Grind disk N/A
Min. Surface
Preparation

Wire brush Wire brush Wire brush Wire brush Wire brush Wire brush Wire brush Wire brush N/A
Methods
Needle gun Needle gun Needle gun Needle gun Needle gun Needle gun Needle gun Needle gun N/A
Bristle Blaster Bristle Blaster Bristle Blaster Bristle Blaster Bristle Blaster Bristle Blaster Bristle Blaster Bristle Blaster N/A
Expected lifetime 15 years 15 years 15 years 15 years 15 years 15 years 15 years 15 years N/A
Warranty on request on request on request on request on request on request on request on request N/A
Solvent wash SSPC-SP1
Cleanliness Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501 Sa 2½ - ISO 8501
Sweep blasting SSPC-SP7 / Sa 1 ISO 8501
Optimal Surface

> 60 µm > 60 µm > 60 µm > 60 µm > 60 µm > 60 µm > 60 µm > 60 µm 120-180 grade for coating
Preparation

Roughness 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 2/3 ISO 8501 60-120 grade for concrete
Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3 Concrete: CSP 3
Methods Abrasive Blasting Abrasive Blasting Abrasive Blasting Abrasive Blasting Abrasive Blasting Abrasive Blasting Abrasive Blasting Abrasive Blasting Orbital electric sander or abrasive paper
Expected lifetime > 30 years > 30 years > 30 years > 30 years > 30 years > 30 years > 30 years > 30 years 10 years
Warranty on request on request on request on request on request on request on request on request on request
Primer needed No No No No No No No No Yes
Temperature before mixing 18°C - 25°C 18°C - 25°C 18°C - 25°C 35°C - 40°C 50°C - 60°C 20°C - 25°C 18°C - 25°C 15°C - 25°C 20°C-25°C
Application temperature of mixture 25°C ± 5°C 25°C ± 5°C 30°C ± 5°C 35°C ± 5°C 55°C ± 5°C 25°C ± 5°C 18°C - 25°C 15°C - 25°C 25°C ± 5°C
Application
Conditions

Min. surface temperature* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > DPT + 3°C* > 0°C and > DPT + 3°C
Max. surface temperature 50°C 50°C 50°C 50°C 50°C 50°C 50°C 50°C 50°C
Humidity of surface no condensation no condensation no condensation no condensation no condensation no condensation no condensation no condensation no condensation
R.H. < 95% < 95% < 95% < 95% < 95% < 95% < 95% < 95% < 95%
Curing under water possible Yes Yes Yes Yes Yes Yes Yes Yes No

*These criteria are valid to achieve the most durable protection. If a reduced coating lifetime is desired, application can continue outside this window. The existing warranties do not apply in these conditions. Please contact Acotec nv directly for more information on the expected lifetime in these conditions.