SCOPE OF ACCREDITATION TO ISO/IEC 17025:20171
EAGLE OTTAWA LEATHER
2930 W. Auburn Rd.
Rochester Hills, MI 48309
Tom Loseth Phone: 248 844 1304
MECHANICAL
Valid To: December 31, 2024 Certificate Number: 4045.01
In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this
laboratory to perform the following tests on upholstery leather:
Test Device Test Method(s)
Abrasion NS Flat M0602-19.1, -19.3, -19.4
Gakushin 8102Z 6.2.6.2.3.1 / SZ3 4.2.6.2; ES-X83217 4.18;
EX-X83217 4.22; ISC-F20-010Y;
MES MN405 7.14 & 7.19; M0602 20;
TS343-08-006-6.27
Martindale VDA 230-211; AA-0412; ISO 17076-2, 12947-1, -2
Pilling FLTM BN 108-14; TPJLR.52.005
Seat Belt FLTM BN163-01
Taber 8102Z 6.2.6.2.2.1 / SZ3 4.2.6.2; ES-X83217 4.17;
FLTM BN108-02; GMW 3208;
ISO 17076-1, 5470-1; M0602 19;
MES MN405 7.14.2; MS 300-31G 4.19; SAE J948;
TS343-08-006 6.12; TSL5101G 3.8
Wyzenbeek LP-463KB-6-01; TSL 5101G 3.9 & 3.10
Flesh Fiber Fluff TSL 5101G 3.41
Veslic VDA 230-221
Accelerated Aging Humidity Age 8102Z 6.2.7 & 6.2.8 / SZ3 4.2.7 & 4.2.8; AA-0420;
ES-X83217 4.14; ISC-F20-004Y;
LP-463LB-11-02; MN405 7.28; TS343-08-0066.19;
TSL 5101G 3.17 & 3.24;
M1F25B 3.13.3/M99P43E 3.12.3
(A2LA Cert. No. 4045.01) 01/05/2023 Page 1 of 6
Test Device Test Method(s)
Accelerated Aging Cont’d Heat Age 31804676 4.9 & 4.10; ES-X83217 4.13;
8102Z 6.1.7 & 6.2.9; LP-463LB-13-01;
ISC-F20-0003Y; MBN 55555-4, -6;
MN405 7.28.B.a; TL52064 6.6; TPJLR.52.352;
TS343-08-006 6.18;
M1F25B 3.13.2/M99P43E 3.12.2;
VCS 1027,2729; TSL 5101G 3.23
Hydrolytic Aging VDA 230-208
Environmental FLTM BO040-01; ES-X83217 4.15; GMW 14124;
Cycle LP-463LB-12-01; LP-463DD-08-02;
M0602 26 & 28; MBN 55555-4 5.26;
TS343-08-006 6.20; TL52064 6.9;
Volvo 31804676 4.11; PV1200
Adhesion Finish Adhesion 8102Z 6.2.12.1; GMW 15717; ISC-F20-007Y;
ISO 11644; TS343-08-006 6.21; TSL5101G 3.30;
IUF 470
Bond Strength AA-0496; FLTM BN151-05; GMW 3220; ISO 2411;
TPJLR.52.058; LP-463LB-10-01
Air Permeability ASTM D737; JLR TPJLR.01.339; TSL2107G;
ISO 9237
Blocking and Migration 8102Z 6.2.4; DIN 53343; ES-X83217 4.13;
ISC-C93-0003A 4.2; FLTM BN 103-01;
GMW14132; ISO 15701; LP-463LB-05-01;
M0602 25 & 33; MBN55555-6 5.12;
MES MN405 7.27; MS 300-31 4.13; SAE J912;
TPJLR.52.712; TS343-08-006 6.14;
TSL5101G 3.16 & 3.20; JLR TPJLR.52.209
Cold Flexibility Cold Flex 8102Z-TZAA-JZ00 B-11-1; AA 0563
Cold Fold TS343-08-006 6.17; 8102Z 6.2.2; M0602 31;
MES MN405 7.32; SAE J323 Method A;
VCC 85000125
Cold Impact LP-463KB-28-01-B; ES-X83217 4.14;
GMW 14126, 14127; TSL5101G 3.15;
MS 300 31G Sec. 4.14
Conditioning GMW3221, Code A & B; ISO 2419;
ASTM D1610, Option 1
Crocking Crockmeter FLTM BN 107-01; ISC-F20-011Y; ISO 105-X12;
MS 300-31G 4.12; SAE J861; TS343-08-006 6.11.2;
TSL5101G 3.19 & 3.39
(A2LA Cert. No. 4045.01) 01/05/2023 Page 2 of 6
Test Device Test Method(s)
Crocking Cont’d Gakushin 8102Z 6.2.5.2; ES-X83217 4.12.4; M0602 21;
MES MN405 7.21; NES M0602-21, -23
Veslic ISO 11640; MBN 55555-7
Elongation 8102Z 6.1.3; ASTM D2211, D5034;
ISO 13934-1, 3376; GMW3010; M0602 11;
MES MN405 7.5.1; MS 300-31G 4.6;
TS343-08-006 6.5.3; TSL5101G 3.4.2 & 3.27
Evaluation ISO 105-A02, -A03, -A04, -A05;
AATCC EP1, EP2; SAE J1545; FLTM BI109-01
Flammability DBL 5307; ES-X60410; FMVSS 302;
GMW 3232; GS 97038; HES D6003-99; ISO 3795;
MES CF 050; MS 300-08; NES M 0094;
TL1010; TSM0500G; VCS 5031,19; MS-JP-9-4;
TS420-00-002
Flexibility Bally Flex ISO 5402-1; ASTM D6182; AA-0563;
FLTM BN162-01; VCC 85000110
W Flex TS343-08-006 6.15.2A; ASTM D2097;
MS300-31 4.35; TPJLR.52.413; TSL5101G 3.14.2
Crumple Flex TSL5101G 3.29; 8102Z 6.2.3; M0602 18
Fogging DIN 75 201-B; ES-X83217 4.23; GMW3235;
HES D6508; MES MN405 7.34;
MS 300-54; NES M0161 30; SAE J1756;
TSM0503G; VCS 1027, 2719; LP463DB-12-01
Friction ES-X83217 4.30; M0602 34; 8102Z-TZAA 6B16
MBN55555-6 5.10; MES MN405 7.46;
MS 300-31G 4.29; TSL5101G 3.28; VDA 230-206;
NES M0602-34
Gloss FLTM BI 110-01
Grain Depth MBN 55555-3; ISO 4287; VDA 2006
Heating/Cooling PV 3967
Hole Diameter PV3358
Hydrogen Suflide TS343-08-006 6.16; TSL5101G 3.21
Resistance
(A2LA Cert. No. 4045.01) 01/05/2023 Page 3 of 6
Test Device Test Method(s)
Lightfastness FLTM BO116-01; HES D6601; ISC-F20-013Y;
ISO 105-B06, 17228; M0602 32.1; MBN 55555-5
5.2; MES MN135 7.23.1.A; MS 300-31G 4.12.2;
SAE J2412; STD 1026, 8243; TS343-08-006 6.13;
TSL5101G 3.18.3; VCC 85000140; VCS 1027, 359;
VDA 230-216; PV1303
Loose Grain Effect TSL5101G 3.42, TS343-08-006-6.28; 8102Z 6.C.7;
VDA 230-205; GMW14136; NES M0602-43;
ISO 4287
Mass & Density ASTM D3776, Option C; ES-X83217 4.1;
GMW3182; ISO 2420; MES MN405 7.2;
MS300-31G 4.1; NES M0602 Sec. 7; TPJLR.52.708;
TS343-08-006 6.3; TSL5101G 3.1
Moisture Vapor GMW 14140
Permeability
Mold Resistance PV 3970; M1F25B 3.16 / M9943E 3.11.9;
GMW 3259; TPJLR.52.351
Odor FLTM BO131-03; ES-X83217 4.5; GMW3205;
M0602 38; MES MN405 7.37; MS 300-34J;
SAE J1351; TPJLR.52.458; TS300-00-001,
TS343-08-006-6.23; TSM0505G; VCS 1027, 2729;
VDA 270-C3; 8102Z-TZAA 6C1
Perspiration Resistance LP-463KC-21-01; ISO 105-E04; GMW14296;
AA-0567; NES M0602-22
Pliability Bending Stiffness VDA 230-209; AA-0551; MBN 55555-6 5.15
Cantilever ASTM D1388 Method A; ES-X83217 4.21;
Stiffness FLTM BN157-02; TS343-08-006 6.10; GMW3390;
8102Z 6.1.8; MS 300-31G 4.20; TPJLR.52.705;
MES MN405 7.8; M0602 8; TSL5101G 3.3.1
Compression TSL5101G 3.3.2
Stiffness
Softness (BLC) ISO 17235; FLTM BN 157-01; MES MN405 7.41;
GMW 14134; NES M0602-42
Stiffness JLR TPJLR.52.705; MS300-31 4.21
Reflectance PR 358
Sampling ISO 2418; ASTM D2813; MS 300-11
(A2LA Cert. No. 4045.01) 01/05/2023 Page 4 of 6
Test Device Test Method(s)
Scratch / Scuff SAE J365; ISC-C93-003A 4.3; M0602 Sec. 17;
MS 300-11; TSL5101G 3.13.1; MBN55555-6;
VDA 230-218
Seam Fatigue TSL5101G 3.7; GMW3405; FLTM BN106-02;
MS300-31 4.27; TS343-08-006-6.32
Seam Strength 8102Z 6.1.5; ES-X83217 4.27; LP-463KB-13-01;
ISO 13935-1; M0602 13; MES MN405 7.9.1;
MS 300-31G 4.27; TS343-08-006 6.7;
TSL5101G 3.6
Shrinkage 8102Z 6.1.7; AA-0568; FLTM BN 105-03;
PV 1200; TL52064 6.6; TPJLR.52.304;
TS343-08-006 6.9; ISO 17228, 17130;
MN405S-7.28
Soiling, Staining & 8102Z 6.2.13, 6.2.14, 6.2.15, 6.2.17, 8102Z-TZAA
Cleaning 6B10; AA-0419, -0566, 0567;
AATCC 118; ASTM D6012; ES-X83217 4.25;
FLTM BI 113-08; FLTM BN110-02;
FLTM BN112-08; GMW 15377, 3402, 14445,
14864; GS97034-5; ISO 26082;
LP-463PB-31-01, LP-463KC-04-01,
LP-463KC-04-02, LP-463KC-04-03,
LP-463KC-15-01, LP463KC-21-01, LP463LB-05-
01; M0602 24, 35 & 41; MBN55555-3, -7;
MS 300-31G 4.34, MS 300-31G 4.33; PV 3964,
3968; NES M0602-24; TPJLR.52.201, 52.202,
52.205, 52.210, 52.211, 52.212; TS343-08-006-6.16,
-6.22, -6.26, -6.31; TSL5101G 3.21, 3.25, 3.32, 3.33,
3.34; VCC 85000120; VCC 85000145;
VCC 85000150; VCC 85042802; VDA 230-212
Stitch Tear GMW 14146; ISO 23910; TPJLR.52.414;
TSL5101G 3.7
Stretch & Set 8102Z 6.1.6; GMW3211; MES MN405 7.7.1;
MS 300-31G 4.8; PV 3909 Method 2; SAE J855;
TPJLR.52.302; TS343-08-006 6.8; TSL5101G 3.31
Tear Strength 8102Z 6.1.4; ASTM D5587, D5733, D6077;
ES-X83217 4.9; ISO 13937-2, 3377-1; M0602 12;
MES MN405 7.6.1 & 7.24; MS 300-31G 4.9;
STD 1024,3725; TPJLR.52.425;
TS343-08-006 6.6.3; TSL5101G 3.5.1
(A2LA Cert. No. 4045.01) 01/05/2023 Page 5 of 6
Test Device Test Method(s)
Tensile Strength 8102Z 6.1.2; ASTM D2208, D2209, D5034;
DIN EN ISO 3376; ES-X83217 4.6; GMW 3010;
ISO 3376, 13934-1; M0602 11;
MES MN405 7.5.1.A.a; MS 300-31G 4.6;
VCS1024,2135; TS343-08-006 6.5.2;
TSL5101G 3.4.2
Thickness 8102Z 6.1.1; ASTM D1813; ES-X83219 4.3;
ISO 2589, 5084, 2286-3, 17186; M0602 6;
MES MN405 7.3; MS 300-31G 4.3;
TS343-08-006 6.4; TSL5101G 3.2
Water Resistance TL52064 6.5; VDA 230-216; LP-463KC-03-01;
GMW 14102
Wrinkling LP-463KB-24-01; NES M0602 43
1
When the date, revision or edition of a test method standard is not identified on the scope of
accreditation, the laboratory is required to be using the current version within one year of the date of
publication, per part C., Section 1 of A2LA R101 - General Requirements - Accreditation of ISO-IEC
17025 Laboratories.
2
The laboratory is accredited for the test methods listed above. The accredited test methods are used in
determining compliance with any material specifications included on this Scope; however, the inclusion
of these material specifications on this Scope does not confer laboratory accreditation to the material
specifications. Inclusion of these material specifications on this Scope also does not confer accreditation
for every method embedded within the specification. Only the methods listed above on this Scope are
accredited.
VCC 85000125, MS-JP-9-4, VCC 85000110, ISO 4287, VDA 2006, TL52064 6.6, VCC 85000120, VCC
85000145, VCC 85000150, VCC 85042802, TL52064 6.5, VDA 230-216.
(A2LA Cert. No. 4045.01) 01/05/2023 Page 6 of 6
Accredited Laboratory
A2LA has accredited
EAGLE OTTAWA LEATHER
Rochester Hills, MI
for technical competence in the field of
Mechanical Testing
This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017
General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates
technical competence for a defined scope and the operation of a laboratory quality management system
(refer to joint ISO-ILAC-IAF Communiqué dated April 2017).
Presented this 5th day of January 2023.
_______________________
Mr. Trace McInturff, Vice President, Accreditation Services
For the Accreditation Council
Certificate Number 4045.01
Valid to December 31, 2024
For the tests to which this accreditation applies, please refer to the laboratory’s Mechanical Scope of Accreditation.
