SmartSolar Charge Controllers MPPT 100/30 & 100/50
www.victronenergy.com
Bluetooth Smart built-in
The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.
VE.Direct
For a wired data connection to a Color Control GX, other GX products, PC or other devices
Ultrafast Maximum Power Point Tracking (MPPT)
Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve
energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.
Advanced Maximum Power Point Detection in case of partial shading conditions
If partial shading occurs, two or more maximum power points may be present on the power-voltage curve.
Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP.
The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP.
Outstanding conversion efficiency
No cooling fan. Maximum efficiency exceeds 98%.
The full output current up to 40°C (104°F).
Flexible charge algorithm
Fully programmable charge algorithm (see the software page on our website), and eight pre-programmed algorithms,
selectable with a rotary switch (see manual for details).
Extensive electronic protection
Over-temperature protection and power derating when temperature is high.
PV short circuit and PV reverse polarity protection.
PV reverse current protection.
Internal temperature sensor
Compensates absorption and float charge voltage for temperature.
SmartSolar Charge Controller
Optional external battery voltage and temperature sensing via Bluetooth
MPPT 100/50
A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to
one or more SmartSolar Charge Controllers.
Fully discharged battery recovery function
Will initiate charging even if the battery has been discharged to zero volts.
Will reconnect to a fully discharged Li-ion battery with integrated disconnect function.
Bluetooth sensing
Smart Battery Sense
SmartSolar Charge Controller MPPT 100/30 MPPT 100/50
Battery voltage 12/24V Auto Select
Rated charge current 30A 50A
Nominal PV power, 12V 1a,b) 440W 700W
Nominal PV power, 24V 1a,b) 880W 1400W
Maximum PV open circuit voltage 100V 100V
Max. PV short circuit current 2) 35A 60A
Maximum efficiency 98% 98%
Self-consumption 12V: 30 mA 24V: 20 mA
Charge voltage 'absorption' Default setting: 14,4V / 28,8V (adjustable)
Charge voltage 'float' Default setting: 13,8V / 27,6V (adjustable)
Bluetooth sensing Charge algorithm multi-stage adaptive
BMV-712 Smart Battery Monitor Temperature compensation -16 mV / °C resp. -32 mV / °C
PV reverse polarity
Protection Output short circuit
Over temperature
Operating temperature -30 to +60°C (full rated output up to 40°C)
Humidity 95%, non-condensing
VE.Direct
Data communication port
See the data communication white paper on our website
ENCLOSURE
Colour Blue (RAL 5012)
Power terminals 16 mm² / AWG6
Protection category IP43 (electronic components), IP22 (connection area)
Weight 1,3 kg
Dimensions (h x w x d) 130 x 186 x 70 mm
STANDARDS
Safety EN/IEC 62109-1, UL 1741, CSA C22.2
1a) If more PV power is connected, the controller will limit input power.
1b) The PV voltage must exceed Vbat + 5V for the controller to start.
Thereafter the minimum PV voltage is Vbat + 1V.
2) A PV array with a higher short circuit current may damage the controller.
Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands
General phone: +31 (0)36 535 97 00 | E-mail:
[email protected]www.victronenergy.com
