DIGITAL STILL CAMERA

DSC-HX90
DSC-HX90V

SERVICE MANUAL
1st Edition (Revised 1)
 WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.

WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.

AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

DSC-HX90/DSC-HX90V
 FÖRSIKTIGHET!

Fara för explosion vid felaktigt placerat batteri.

Byt endast mot samma eller likvärdig typ av batteri,
enligt tillverkarens rekommendationer.
När du kasserar batteriet ska du följa rådande lagar
för regionen eller landet.

CAUTION
PAS PÅ
Danger of explosion if battery is incorrectly replaced.
Fare for eksplosion, hvis batteriet ikke udskiftes
Replace only with the same or equivalent type rec-
korrekt.
ommended by the manufacturer.
Udskift kun med et batteri af samme eller tilsvarende
When you dispose of the battery, you must obey the
type, som er anbefalet af fabrikanten.
law in the relative area or country.
Når du bortskaffer batteriet, skal du følge
lovgivningen i det pågældende område eller land.

ATTENTION
HUOMIO
Il y a danger d’explosion s’il y a remplacement incor-
rect de la batterie. Remplacer uniquement avec
Räjähdysvaara, jos akku vaihdetaan virheellisesti.
une batterie du même type ou d’un type équivalent
Vaihda vain samanlaiseen tai vastaavantyyppiseen,
recommandé par le constructeur.
valmistajan suosittelemaan akkuun.
Lorsque vous mettez la batterie au rebut, vous devez
Noudata akun hävittämisessä oman maasi tai
respecter la législation en vigueur dans le pays ou la
alueesi lakeja.
région où vous vous trouvez.

FORSIKTIG
VORSICHT
Eksplosjonsfare hvis feil type batteri settes i.
Explosionsgefahr bei Verwendung falscher Batterien. Bytt ut kun med samme type eller tilsvarende
Batterien nur durch den vom Hersteller empfohlenen anbefalt av produsenten.
oder einen gleichwertigen Typ ersetzen. Kasser batteriet i henhold til gjeldende avfallsregler.
Wenn Sie die Batterie entsorgen, müssen Sie die
Gesetze der jeweiligen Region und des jeweiligen
Landes befolgen.
⊼ᛣ

བᵰ᳈ᤶⱘ⬉∴ϡℷ⹂ˈህӮ᳝⟚⚌ⱘॅ䰽DŽ
া᳈ᤶৠϔ㉏ൟ៪ࠊ䗴ଚ᥼㤤ⱘ⬉∴ൟোDŽ
໘⧚⬉∴ᯊˈᖙ乏䙉ᅜⳌ݇ഄऎ៪೑ᆊⱘ⊩ᕟDŽ

Note:
Be sure to keep your PC used for service and checking of this
unit always updated with the latest version of your anti-virus
software. In case a virus affected unit was found during service,
contact your Service Headquarters.

DSC-HX90/DSC-HX90V
 SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered UNLEADED SOLDER
connections. Check the entire board surface for solder splashes This unit uses unleaded solder.
and bridges. Boards requiring use of unleaded solder are printed with the lead free
2. Check the interboard wiring to ensure that no wires are “pinched” mark (LF) indicating the solder contains no lead.
or contact high-wattage resistors. (Caution: Some printed circuit boards may not come printed with
3. Look for unauthorized replacement parts, particularly transistors, the lead free mark due to their particular size.)
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs : LEAD FREE MARK
of deterioration. Point them out to the customer and recommend Be careful to the following points to solder or unsolder.
their replacement.
5. Check the B+ voltage to see it is at the values specified. • Set the soldering iron tip temperature to 350 °C approximately.
6. Flexible Circuit Board Repairing If cannot control temperature, solder/unsolder at high temperature
• Set the soldering iron tip temperature to 350 °C approximately. for a short time.
• Do not touch the soldering iron on the same conductor of the Caution: The printed pattern (copper foil) may peel away if the
circuit board (within 3 times). heated tip is applied for too long, so be careful!
• Be careful not to apply force on the conductor when soldering Unleaded solder is more viscous (sticky, less prone to
or unsoldering. flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

DSC-HX90/DSC-HX90V
 0

DSC-HX90/DSC-HX90V
 Model Information

Model HX90 HX90V

Destination CE3, CEH, RU3, CN1 U2, CA2, TW6, KR2, J1 CE3, CEH, E32, EA8, AU2,
HK1, IN5
Color system PAL NTSC PAL
GPS – ✓ ✓
Wi-Fi ✓ ✓ ✓
NFC ✓ ✓ ✓

DSC-HX90/DSC-HX90V 7
 Table of Contents

Model Information

Manual Structure

Purpose of this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Related manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

1. Trouble Shooting

1-1. Self-diagnosis Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-1-1. Self-diagnosis Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1-1-2. Note on the Function of Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-1-3. Self-diagnosis Code Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-2. Process after Fixing Flash Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
1-2-1. E:91:01 Flash Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

2. Service Note

2-1. Operation Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-1-1. Flexible Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-1-2. Fine-Wire Coaxial Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-1-3. Discharging of the Flash Capacitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
2-2. Precaution on Replacing the SY-1056 Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-1. Destination Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-2. USB Serial No. and Product ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-3. Restore Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-4. Angular Velocity Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-5. Update of MAC Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2-3. Checking the Wi-Fi Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-4. Cleaning of the EVF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2-4-1. Removing the VF Lens Tube Assy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

3. Adjustment

4. Replacement of Main Parts

4-1. Identifying Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4-2. Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4-2-1. Overall Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4-2-2. Main Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
4-2-3. BT Holder Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
4-2-4. Front Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4-2-5. Upper Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
4-2-6. LCD Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
4-2-7. Lens Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
4-3. Lens Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

DSC-HX90/DSC-HX90V 1
 4-3-1. Ornamental Ring A or Barrier Assy Replacing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
4-3-2. 2 Group Frame Block Assy Replacing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

5. Repair Parts List

5-1. Note on Repair Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5-2. Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Overall Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Main Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
BT Holder Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Front Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Upper Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LCD Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Lens Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
5-3. Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5-4. Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10

6. Frame Schematic Diagrams

Frame Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Revision History

DSC-HX90/DSC-HX90V 2
 Manual Structure

Purpose of this manual

This manual describes the information items that premise the service based on the components parts assuming use of
system and service engineers.

Related manuals

Besides this manual, the following manuals are available.

• Operating Guide (Supplied with this unit)
• Help Guide (Web manual)
Refer to “Help Guide” for in-depth instructions on the many functions of the camera.
• Adjust Manual (Available on request)
The adjustment software is necessary for adjustment and various checking of this unit for the service.

DSC-HX90/DSC-HX90V 3
 目次

このマニュアルについて

本書の目的. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
関連マニュアル. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1. トラブルシューティング

1-1. 自己診断機能. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1-1-1. 自己診断機能について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-1-2. 基板について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1-1-3. 自己診断コード表. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-2. フラッシュエラーの解除方法. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
1-2-1. E：91：01 フラッシュエラー. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

2. サービスノート

2-1. 作業時の注意. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2-1-1. フレキシブル基板. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-1-2. 細線ケーブル. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2-1-3. フラッシュ用充電コンデンサの放電について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2. SY-1056 基板交換時の注意. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-1. 仕向データ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-2. USB シリアルナンバーとプロダクト ID について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-3. リストアデータ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-4. 角速度センサー. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-2-5. MAC アドレスの更新. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2-3. Wi-Fi 接続確認. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2-4. EVF の清掃について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-4-1. VF レンズ筒 ASSY の外し方. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

3. 調整について

4. Replacement of Main Parts

4-1. Identifying Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4-2. Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4-2-1. Overall Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
4-2-2. Main Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4-2-3. BT Holder Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4-2-4. Front Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4-2-5. Upper Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
4-2-6. LCD Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
4-2-7. Lens Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
4-3. Lens Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23
4-3-1. Ornamental Ring A or Barrier Assy Replacing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
4-3-2. 2 Group Frame Block Assy Replacing Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

DSC-HX90/DSC-HX90V 1
5. Repair Parts List

5-1. Note on Repair Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

5-2. Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Overall Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Main Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
BT Holder Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Front Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Upper Cabinet Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LCD Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
Lens Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
5-3. Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5-4. Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

6. Frame Schematic Diagrams

Frame Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

DSC-HX90/DSC-HX90V 2
 このマニュアルについて

本書の目的

本書は，システムエンジニアやサービスエンジニアの 方々にご使用いただくことを想定し，本機の保守に関
する情報，部品レベルまでのサービスを前提とした情報を記載しています。

関連マニュアル

本機には，この「サービスマニュアル」のほかに，下記のマニュアルが用意されています。
• 取扱説明書（本機に付属）
• ヘルプガイド（Web 取扱説明書）
Web 上のマニュアル「ヘルプガイド」もご覧ください。パソコンやスマートフォンでご覧いただけます。
• アジャストマニュアル（別途用意）
本機の調整および各種動作確認を行うのに必要なサービス用の調整ソフトウェアです。

DSC-HX90/DSC-HX90V 3
 Section 1
Trouble Shooting

1-1. Self-diagnosis Function

1-1-1. Self-diagnosis Function

If an error occurs in this unit, the self-diagnosis function starts working and a code consisting of one alphabet and a four-
digit number appears on the LCD. Classification of persons in charge, classification of faulty blocks, and details of errors
can be checked by referring to this indication of five alphanumeric characters in the self-diagnosis code table.
The history of past errors can be checked in “Usage and Diag record” on the DATA tab of the Adjust Manual.
The self-diagnosis function is also described in the operation manual.

1-1-2. Note on the Function of Boards

The boards and functions used in this model are mentioned in the following table.

Board Function
CD board Imager
BT board Battery
EV board EVF control
LC board LCD
RL board ROLL angular velocity sensor, GPS (HX90V)
SE board Eyepiece sensor
ST board Flash control
SY board CPU, power control, Lens control, PITCH/YAW angular velocity sensor, Other function

1-1-3. Self-diagnosis Code Table

Self-diagnosis Code
Repaired by:

Block Detailed Symptom/State Correction

Function Code

C 13 01 Memory card is unformatted or Format the memory card.

memory card is broken. Insert a new memory card.
C 32 01 Trouble with hardware Turn power off and turn power on again.
E 41 00 Abnormality of the wireless LAN The peripheral circuit of between CPU and wireless LAN
module or CPU module may be faulty.
Replace the board that contains this peripheral circuit.
E 41 01 Abnormality of network control de- Turn power off and turn power on again.
vice
E 61 00 Difficult to adjust focus Turn power off and turn power on again. When this error is
(Cannot initialize focus) not cleared, the focus control signal for the lens block may
be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.

Continued

DSC-HX90/DSC-HX90V 1-1
 Self-diagnosis Code
Repaired by:

Block Detailed Symptom/State Correction

Function Code

E 61 10 Zoom operations fault Turn power off and turn power on again. When this error is
(Cannot initialize zoom lens) not cleared, operate the zoom lever and check following
items.
• When zooming is performed, the zoom control signal
for the lens block may be faulty.
• When zooming is not performed, the zoom motor
drive circuit may be faulty.
Check whether this error is due to the lens or the board.
Replace the faulty lens or board.
E 61 30 Reset position detection error on the Turn the power on to open lens barrier. Disconnect the bat-
stepper iris initializing tery or power cord, and then connect again. And confirm
that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive cir-
cuit in lens drive block. If iris blades work normally, con-
firm that they are closing completely and confirm following
items.
• Case of the iris blades do not close normally. Replace
the lens block.
• Case of “E: 61: 30” is appeared and iris blades closed
completely. Confirm that communication with lens
block is normal.
• Case of LCD is not displayed normally, check that
connection between imager board and main board.
• Case of LCD is displayed normally, replace the lens
block.
E 62 02 Abnormality of IC for steadyshot. Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.
E 62 10 Shift lens initializing failure Replacement of lens block. *1
If an error occurs again, steadyshot circuit may be faulty.
Replace the board that contains this peripheral circuit.
E 62 11 Shift lens overheating (PITCH) Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.
E 62 12 Shift lens overheating (YAW) Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.
E 62 20 Abnormality of thermistor Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.
E 91 01 Abnormality when flash is being Checking of flash unit or replacement of flash unit.*2
charged
E 92 00 Battery/Dry cell distinction defect Turn power off and turn power on again.
E 94 00 Fault of writing or erasing the inter- The internal memory (CPU) may be faulty.
nal memory Replace the board that contains this peripheral circuit.

Continued

*1: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After
the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*2: After check, be sure to perform “1-2. Process after Fixing Flash Error”.

DSC-HX90/DSC-HX90V 1-2
 Self-diagnosis Code
Repaired by:

Block Detailed Symptom/State Correction

Function Code

E 95 00 GPS hardware error Check the signal line connection for GPS.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.
E 95 01 Acceleration sensor hardware error Turn power off and turn power on again. When this error is
not cleared, the peripheral circuit of the acceleration sensor
may be faulty.
Replace the board that contains this peripheral circuit.
E 95 0 2 *1 Electronic compass hardware error The peripheral circuit of the electronic compass may be
(GPS hardware error) faulty.
Replace the board that contains this peripheral circuit.

*1: Function of this code is not provided in this unit.

DSC-HX90/DSC-HX90V 1-3
1-2. Process after Fixing Flash Error

1-2-1. E:91:01 Flash Error

When “FLASH error” (Self-diagnosis Code E:91:01) occurs, to prevent any abnormal situation caused by high voltage,
setting of the flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated.

Method of initializing the flash error code:

Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe.

DSC-HX90/DSC-HX90V 1-4
 Section 2
Service Note

2-1. Operation Notes

2-1-1. Flexible Board

• Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
• Do not touch the conductive side of flexible boards with bare hands.
• Plug in a flexible board straight, fully into the connector until it reaches the end inside.

OK NG NG
(The flexible board was plugged in (The flexible board was plugged in (The flexible board was not plugged in
straight and completely) crooked.) completely.)
Flexible Flexible
Board Flexible Flexible Board Flexible
Board Board Board
Reference line Reference line
Flexible
Reference line Board

Connector Connector Connector Connector Connector Connector

• When opening the connector's holder in direction A, do not open it with excessive force.

Holder
A
Connector
A Flexible Board

• When closing the connector's holder, press it evenly while pushing a flexible board in direction B.

Holder
Connector
Flexible Board

Insulation side

• Make sure that the flat cable and flexible board are not cracked or bent at the contact end.

Cut and remove the part of gilt

which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

• Do not apply excessive force to the gilded flexible board.

2-1-2. Fine-Wire Coaxial Cable

• The proper way to disconnect a connector is to grab the connector instead of the wires. If you pull on the wires,
they might be broken.
• The proper way to connect a connector is to grab the connector instead of the wires. If you push on the wires, they
might be broken.

DSC-HX90/DSC-HX90V 2-1
2-1-3. Discharging of the Flash Capacitor

The charging capacitor for the flash has been charged at high voltage. Therefore, there is a possibility of an electric
shock if you directly handle this capacitor.
The high-voltage charge will not be discharged by simply turning off the unit’s power. Make sure any remaining voltage
is discharged by short-circuiting the flash capacitor with a Short Jig.

Preparing the Short Jig

Make a Short Jig by connecting a small clip to each lead of a resistor with a rated value of approximately 1 kΩ/1 W.
In order to prevent an electric shock, wrap insulating tape completely around the resistor and its leads.

Resistor with a rated value of approximately

1 k/1 W (Part No. 1-215-869-11).

Small clip Small clip

Wrap insulating tape completely

around the resistor and its leads.

DSC-HX90/DSC-HX90V 2-2
2-2. Precaution on Replacing the SY-1056 Board

The board for repair is not recorded the information unique to a model. Therefore the following data are needed to write.
Note
The [LOAD AND WRITE] function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust Manual
overwrites all data of the unit. Therefore execute the [LOAD AND WRITE] before performing the following operation.

2-2-1. Destination Data

The destination data stored in the repairing board is different from the destination setting stored in the board before
replacement in some cases.
When the board has been replaced with a repairing board, be sure to set the destination.

Method of the destination data write:

Start the Adjust Manual in the Adjust Station and execute the “Destination data write” on the ADJUST tab.

2-2-2. USB Serial No. and Product ID

The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have
been written.
These IDs have not been written in a new repairing board. Therefore, after the board has been replaced, be sure to write
these IDs to a new repairing board.

Method of the ID writing:

Start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB SERIAL No. INPUT” on
the ADJUST tab.

2-2-3. Restore Data

Before replacing the board with a repairing board, be sure to extract the data from the former one.

Method of the data extracting:

Start the Adjust Manual in the Adjust Station and execute the “RESTORE DATA” on the DATA tab.

2-2-4. Angular Velocity Sensor

Before replacing the board with a repairing board, be sure to record the sensitivity indicated on the angular velocity
sensor on the repairing board.
The recorded sensitivity indication must be stored in the repairing board.

Method of the angular velocity sensor sensitivity writing:

Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj” on the
ADJUST tab.
Note
The sensitivity of the angular velocity sensor is indicated only on the repairing board, but is not indicated on mass
production boards.

DSC-HX90/DSC-HX90V 2-3
2-2-5. Update of MAC Address

When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the
IC’s unique number (MAC address) must be reloaded.

Procedure of the MAC address update:

Note
Perform the below operations after all work has been done.

1. Start the Adjust Manual in the Adjust Station and execute the “Wireless LAN Setting (MAC Address)” on
the ADJUST tab.
2. Operate the unit to initialize of SSID/PW.

Applicable parts:
• SY-1056 Board
Note
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required.
Accordingly, download the Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach
it to the set when returning the set to customer.

DSC-HX90/DSC-HX90V 2-4
2-3. Checking the Wi-Fi Function

After this unit has been disassembled and reassembled, check the Wi-Fi function.

Required equipment:
Windows PC or smartphone with Wi-Fi interface

Procedure:
1. Turn on the power of the unit and enable the Wi-Fi function.
(Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.)
2. Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network.

DSC-HX90/DSC-HX90V 2-5
2-4. Cleaning of the EVF

This unit makes it possible to disassemble the EVF from the finished state to clean it. When a problem related to dust
is indicated from a customer, remove the VF Lens Tube Assy in the following procedure and clean it.
When cleaning the VF Lens Tube Assy, use birdlime or the like to remove dust.
• Recommended jig: J-6082-726-A Cleaning Stick II
Note
• Carry out the cleaning work in a clean environment to avoid dust or foreign matter during disassembling.
Use a clean booth if possible.
• Do not use an air blower because it raises surrounding dust.
• Do not use cleaning cloth that causes wiping unevenness.

2-4-1. Removing the VF Lens Tube Assy

Preparation:
Make a jig as shown below by bending fine wire.

Approx. 5 mm
Approx. 0.7 mm
Approx. 30 mm

Approx. 30 mm

Procedure:
1. Depress the viewfinder pop-up switch to pop up the EVF.
2. Draw the VF Lens Tube Assy.

Holes

Viewfinder
pop-up switch

DSC-HX90/DSC-HX90V 2-6
 3. Insert both ends of the jig into the holes of the VF Lens Tube Assy, gently hold the jig, and then pull out the
VF Lens Tube Assy while pushing the internal bosses.
Note
Do not scratch the main body with the jig.

Note : Be careful not to touch

the grease applied to
below parts.

Grease

VF Lens Tube Assy

DSC-HX90/DSC-HX90V 2-7
 Section 3
Adjustment

For adjusting these models, the Adjust Station and the Adjust Manual are required.

Adjust Station
It is the software to start up Adjust Manual for each model.
The installer of the Adjust Station and the installation manual are attached, be sure to confirm the contents of them.
Adjust Manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust Manual and the installation manual are attached, be sure to confirm the contents of them.
Note
Be sure to install Adjust Station first.

DSC-HX90/DSC-HX90V 3-1
 第1章
トラブルシューティング

1-1. 自己診断機能

1-1-1. 自己診断機能について

本機の動作に不具合が発生した場合，自己診断機能が働き，LCD 画面にアルファベット 1 文字と数字 4 桁

が表示され点滅します。この 5 文字の表示を自己診断コード表と対照して，対応者分類，不具合の生じたブ
ロックの分類および不具合の詳細を確認することができます。
過去に発生した不具合の履歴は Adjust Manual の DATA タブにある“Usage and Diag record”で確認するこ
とができます。
自己診断機能については取扱説明書にも掲載されています。

1-1-2. 基板について

本機で使用している基板の主な機能は以下の通りです。

基板 機能
CD 基板 イメージャー
BT 基板 バッテリー
EV 基板 EVF 制御
LC 基板 LCD
RL 基板 ROLL 角速度センサー, GPS (HX90V)
SE 基板 接眼センサー
ST 基板 フラッシュ制御
SY 基板 CPU，電源制御，レンズ駆動 ，PITCH/YAW 角速度センサー，その他機能

1-1-3. 自己診断コード表

自己診断コード
対 症状／状態 対応／方法
ブロック 詳細
応
機能 コード
者
C 13 01 フォーマットしていないメモ メモリーカードをフォーマットする。
リーカードを入れた。またはメ 新しいメモリーカードに交換する。
モリーカードが壊れている。
C 32 01 ハードウェアトラブルを検出 電源を入れ直す。
した
E 41 00 ワイヤレス LAN モジュール，ま CPU - ワイヤレス LAN モジュール周辺回路の異常が
たは CPU の異常 考えられる。
上記回路を有する基板を交換する。
E 41 01 ネットワーク制御デバイスの 電源を入れ直す。
異常
E 61 00 フォーカスが合いにくい 電源を入れ直す。復帰しない場合，
レンズブロックの
（フォーカスの初期化ができな フォーカス制御系信号の異常が考えられる。
い） 症状がレンズ・基板のどちらに起因するか確認し不
具合があるものを交換する。

次へ続く

DSC-HX90/DSC-HX90V 1-1
 自己診断コード
対 症状／状態 対応／方法
ブロック 詳細
応
機能 コード
者
E 61 10 ズーム動作の異常 （ズームレン 電源を入れ直す。復帰しない場合，ズームレバーを操
ズの初期化ができない） 作して以下の確認をする。
• ズーム動作をした場合，レンズブロックのズー
ム制御系信号の異常が考えられる。
• ズーム動作をしなかった場合，ズームモータ駆
動回路の異常が考えられる。
症状がレンズ・基板のどちらに起因するか確認し不
具合があるものを交換する。
E 61 30 ステッパ IRIS イニシャル時リ 電源を入れてレンズバリアが開いている状態で， バッ
セット位置検出異常 テリまたは電源ケーブルをはずして付け直す。その
際，レンズ内のアイリス羽根が動作していることを確
認する。
アイリス羽根が動作してない場合は，レンズ駆動ブ
ロックのアイリスモータ駆動回路を確認する。 アイリ
ス羽根が動作する場合は，アイリス羽根が完全に閉じ
きることを確認し，以下の内容を確認する。
• アイリス羽根を正常に閉じることができない場
合レンズブロックを交換する。
• アイリス羽根は正常に閉じているが，E:61:30 が
出る場合レンズブロックとの通信ができている
かを確認する。
• 正常に画面が出ていない場合，イメージャ基板
とメイン基板の間の接続を確認する。
• 正常に画面が出ている場合，レンズブロックを
交換する。
E 62 02 手振れ補正用 IC の異常 CPU - 手振れ補正 IC - PITCH/YAW ドライブ間の信号
線の接続を確認する。
異常なければ上記回路を有する基板を交換する。
E 62 10 シフトレンズ初期化異常 レンズブロックを交換する。 *1
エラーが再度発生する場合は，手振れ補正回路の異常
が考えられる。
上記回路を有する基板を交換する。
E 62 11 シフトレンズオーバーヒート CPU - 手振れ補正 IC - PITCH/YAW ドライブ間の信号
(PITCH) 線の接続を確認する。
異常なければ症状がレンズ・基板のどちらに起因す
るか確認し不具合があるものを交換する。
E 62 12 シフトレンズオーバーヒート CPU - 手振れ補正 IC - PITCH/YAW ドライブ間の信号
(YAW) 線の接続を確認する。
異常なければ症状がレンズ・基板のどちらに起因す
るか確認し不具合があるものを交換する。
E 62 20 サーミスタの異常 CPU - 手振れ補正 IC - PITCH/YAW ドライブ間の信号
線の接続を確認する。
異常なければ症状がレンズ・基板のどちらに起因す
るか確認し不具合があるものを交換する。
E 91 01 フラッシュの充電異常 フラッシュユニットを点検または交換する。*2
E 92 00 バッテリ/乾電池判別不良 電源を入れ直す。
E 94 00 内蔵メモリーの書込み/消去動作 内蔵メモリー (CPU) の異常が考えられる。
不良 上記回路を有する基板を交換する。
E 95 00 GPS ハード異常 GPS の信号線の接続を確認する。
接続に問題がない場合は上記回路を有する基板を交
換する。
E 95 01 加速度センサハードウェア異常 電源を入れ直す。復帰しない場合，加速度センサ周辺
回路の異常が考えられる。
上記回路を有する基板を交換する。

次へ続く

*1: レンズブロックを交換した場合は，Adjust Station から Adjust Manual を起動させて必要な調整項目を実施してください。調整後は

手振れ補正 ON の状態にして，手持ち動作で手振れ補正が適切に動作していることを確認してください。
*2: 確認後は，必ず「1-2. フラッシュエラーの解除方法」を行って下さい。

DSC-HX90/DSC-HX90V 1-2
 自己診断コード
対 症状／状態 対応／方法
ブロック 詳細
応
機能 コード
者
E 95 0 2 *1 地磁気センサハードウェア異常 地磁気センサ周辺回路の異常が考えられる。
（GPS ハードウェア異常） 上記回路を有する基板を交換する。

*1: このコードの機能は本機には実装されていません。

DSC-HX90/DSC-HX90V 1-3
1-2. フラッシュエラーの解除方法

1-2-1. E：91：01 フラッシュエラー

本機はフラッシュエラー（自己診断コード E：91：01）が発生した場合，高電圧による異常を防止するため
に自動的にフラッシュ充電および発光禁止の設定に切り替わります。
フラッシュエラー発生後はエラーの解除を行う必要があります。

フラッシュエラーの解除方法：
Flash Error Repair Tool Ver_[].[].exe を使用してフラッシュエラーを解除してください。

DSC-HX90/DSC-HX90V 1-4
 第2章
サービスノート

2-1. 作業時の注意

2-1-1. フレキシブル基板

• フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。
• フレキシブル基板の導電面を素手で触れないようにしてください。
• フレキシブル基板は，コネクターの奥までまっすぐに差し込んでください。

• コネクターの開閉部を開ける際，A 方向に開け過ぎないようにしてください。

• コネクターの開閉部を閉じる際，フレキシブル基板を矢印 B 方向に押しながら，開閉部を均一に押し
てください。

• フラットケーブルおよびフレキシブル基板の端子面に欠け，折れ等がないことを確認してください。

• 金メッキされているフレキシブル基板には，強い負担をかけないでください。

2-1-2. 細線ケーブル

• コネクターを取り外す際に，線材部（極細）を持って引っ張ると断線する恐れがありますので，絶対に
線材部（極細）を持って引っ張らないでください。
• 線材部（極細）を押さえながらコネクターを差し込むと，線材部（極細）が断線する恐れがありますの
で，絶対に線材部（極細）には負担をかけないでください。

DSC-HX90/DSC-HX90V 2-1
2-1-3. フラッシュ用充電コンデンサの放電について

フラッシュ用充電コンデンサは非常に高い電圧で充電されています。そのため，フラッシュ用充電用コンデ
ンサに手を触れた場合には, 感電する可能性があります。
この高電圧は，本機の電源を切っただけでは放電されません。必ずショート治具をフラッシュ用充電コンデ
ンサに接続して残留電圧を放電してください。

ショート治具の準備
ショート治具は 1 kΩ/1 W 程度の抵抗器の両端に小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い，感電しないように処理してください。

1 kΩ/1 W

DSC-HX90/DSC-HX90V 2-2
2-2. SY-1056 基板交換時の注意

補修用基板には機種固有の情報が記録されていないため，下記のデータを書き込む必要があります。
注意
Adjust Manual 内の DATA タブにある“ADJUSTMENT DATA BACKUP”の [LOAD AND WRITE] 機能は，セッ
トのすべてのデータを上書きするので，下記の作業を行う前に実施してください。

2-2-1. 仕向データ

補修用基板に書き込まれている仕向のデータは交換前の基板に書き込まれている仕向の設定と異なってい
る場合があります。
補修用基板に交換した場合は，必ず仕向の設定を行ってください。

仕向設定方法：
Adjust Station から Adjust Manual を起動し，ADJUST タブにある“Destination data write”を実施して
ください。

2-2-2. USB シリアルナンバーとプロダクト ID について

本機は，1 台ごとに異なる固有の ID（USB シリアルナンバー）と機種固有の ID（プロダクト ID）が基板に書

き込まれた後に出荷されています。
新品の補修用基板には，これらの ID が書き込まれていないため，基板を交換した場合は，必ず交換した新
品の補修用基板に ID を書き込んでください。

ID の書き込み方法：
Adjust Station から Adjust Manual を起動し，ADJUST タブにある“PRODUCT ID & USB SERIAL No.
INPUT”を実施してください。

2-2-3. リストアデータ

補修用基板に交換する場合は，必ず事前に交換前の基板からデータを抽出してください。

データの抽出方法：
Adjust Station から Adjust Manual を起動し，DATA タブにある“RESTORE DATA”を実施してください。

2-2-4. 角速度センサー

補修用基板に交換する場合は，必ず補修用基板の角速度センサーに表記されている感度表示をメモなどに
記録してください。
記録した感度表示は補修用基板に書き込む必要があります。

角速度センサー感度書き込み方法：
Adjust Station から Adjust Manual を起動し，ADJUST タブにある“Angular velocity sensor sensitivity
adj”を実施してください。
注意
角速度センサーの感度表示は補修用基板にのみ表記されています。量産用の基板には表記されていま
せん。

DSC-HX90/DSC-HX90V 2-3
2-2-5. MAC アドレスの更新

Wi-Fi 搭載基板を交換した場合，または，メイン IC (CPU) が搭載されている基板を交換した場合は，MAC

アドレスを更新する必要があります。

MAC アドレス更新方法：
注意
下記の操作は全ての作業を実施した後に行ってください。

1. Adjust Station から Adjust Manual を起動し，ADJUST タブにある“Wireless LAN Setting (MAC

Address)”を実施する。
2. 本機を操作し，SSID･PW リセットを行う。

対象部品：
• SY-1056 基板
注意
交換修理後は MAC アドレスが変更されていますので，お客様に接続機器の再設定をしていただく必要があ
ります。
そのため，Flyer of WLAN Reset（Flyer of WLAN Reset_9834752[][].pdf）をダウンロードし，印刷したもの
を本機と一緒にお客様にお渡しください。

DSC-HX90/DSC-HX90V 2-4
2-3. Wi-Fi 接続確認

本機の分解・組立を行った後は，Wi-Fi 機能の確認を行ってください。

用意する機器：
Wi-Fi 接続の可能なパソコンまたはスマートフォンなど

手順：
1. 本機の電源を入れ，Wi-Fi 機能を有効にする。
（Wi-Fi 接続準備が完了すると Wi-Fi 接続のためのパスワードが表示されます。）
2. パソコンまたはスマートフォン側で接続可能な機器として，本機が検出されることを確認する。

DSC-HX90/DSC-HX90V 2-5
2-4. EVF の清掃について

このセットは完成状態から EVF を分解し，清掃を行うことができます。お客様よりゴミ関連の指摘を受け

た場合は，下記の方法で VF レンズ筒 ASSY を外して清掃を行ってください。
清掃する際は、ゴミの除去にはとりもちなどを使用してください。
• 推奨治具：J-6082-726-A クリーニングスティックⅡ
注意
• 分解時に新たなゴミ等が混入しないように，清潔な環境で作業を行ってください。
可能であればクリーンブースを使用してください。
• エアブローは他のゴミを巻き込むので使用しないでください。
• クリーニングクロスは拭きムラができるので使用しないでください。

2-4-1. VF レンズ筒 ASSY の外し方

準備：
針金のような細い棒を加工して，下図のような治具を作る。
5mm
0.7mm
30mm

30mm

手順：
1. ファインダーポップアップスイッチを押し下げて EVF をポップアップさせる。
2. VF レンズ筒 ASSY を引き出す。

DSC-HX90/DSC-HX90V 2-6
 3. 治具を VF レンズ筒 ASSY の穴に入れ，軽く押さえて内部のボスを押し込みながら VF レンズ筒
ASSY を引き抜く。
注意
冶具で本体を傷つけないように注意してください。

Note :

VF ASSY

DSC-HX90/DSC-HX90V 2-7
 第3章
調整について

これらの機種で調整を行なうには，Adjust Station と Adjust Manual が必要です。

Adjust Station とは
機種別の Adjust Manual を起動するためのソフトウェアです。
Adjust Station のインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を
必ず確認してください。
Adjust Manual とは
デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで，調整及び各種動作確認を行うこ
とが可能です。
Adjust Manual のインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を
必ず確認してください。
注意
インストールは必ず Adjust Station を先に行なってください。

DSC-HX90/DSC-HX90V 3-1
 Section 4
Replacement of Main Parts

4-1. Identifying Parts

ST Block Assy (63680)

EVF Block
• EV-1013 Board
LCD Block
• LC-1026 Flexible Board

RL-1042 Board Control Switch Block (SW63680)

Cabinet Upper Block Assy 63680

RL-1045
GPS Ground Sheet SY-1056 Board
Flexible Board
Metal (63680)

BTH Block Assy (680)

ST Lens • BT-2007 Flexible Board
Cover (63680)

Cabinet Rear
(63680)
ST-1034 Flexible Board

Lens Block
Cabinet Front (63680) • CD-1005 Flexible Board

Cabinet Side Block Assy

Cabinet Bottom (63680)

DSC-HX90/DSC-HX90V 4-1
View Position

Top View

Left View
Back View

Front View
Right View

Bottom View

DSC-HX90/DSC-HX90V 4-2
4-2. Disassembly

4-2-1. Overall Section

• Refer to “5-2-1. Overall Section” on exploded view for Ref. No.

[5] LCD Section

#247
(Note 1)
1
[4] 4 (Claws)

[2] 2
(Claw)
(Note 2)

#239
(Note 1)
#247
(Note 1)

3
(Claws)

#239
(Note 1)
#239
Main Section (Note 1)

(Claws)

9 #247
(Claw)
(Note 1)
8 6
(Claws) [3] 5 (Note 2)
#247
(Note 1)
[1] 7

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

Note 2

Be careful not to tear off the flexible board when remove this
part.

DSC-HX90/DSC-HX90V 4-3
Disassembly Places

[1] #247 X 5

Bottom View

#247

#247

[2] Open the HDMI lid, #247 X 2

Left View

#247

[3] #247 X 1 → Open the LCD, #239 X 1

Right View Left View

#247
#239

[5] #239 X 2 → #247 X 3, Claw X 1

Right View Left View Back View

#247

(Claw)

#239 #239
#247

DSC-HX90/DSC-HX90V 4-4
4-2-2. Main Section

• Refer to “5-2-2. Main Section” on exploded view for Ref. No.

[1] ns
(Hook)
BT Holder Section

[2] 56
(Claw)

57
#247 58
(Note 1)
SP901

61

62 (Note 2)
(Size 4.4 x 4.4 mm) 55

54
60

Refer to
“High-voltage Cautions”
C902
64
53 53

Refer to
[3] Lens Section
(Note 3)
C901 “High-voltage Cautions”

52 51

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

Note 2
Use this to cut or splice so that it becomes the designated size.

DSC-HX90/DSC-HX90V 4-5
Note 3
PRECAUTIONS WHEN HOLDING THE LENS BLOCK

Hold the Lens Block at the Do not hold the following part.
center of both sides.
Zoom Motor
Hold here. *Very weak Connector

Focus Lens
Lens Barrier
Focus Unit *Very weak
*Very weak
*Very weak

High-voltage Cautions

Discharging the Capacitor:

Short-circuit between two points with the short jig about 10 seconds.
1. Disassembly the unit until as shown in the figure below (remove the lens block).

Lens block.

2. Down the pop-up lever to raise the EVF.

Pop-up lever

DSC-HX90/DSC-HX90V 4-6
3. Unlock the connector of the EV-1013 Board, and disconnect the ST-1034 Flexible Board.
Note
Do not touch the flexible board for Flash Unit, because it is high-voltage part.

ST-1034 Flexible Board

Disconnect the ST-1034

Flexible Board.

High-voltage part.
Do not touch.

4. Peel the adhesive sheet of the ST-1034 Flexible Board, and pull out the flexible board as shown in the figure
below.

Terminals of
flash capacitor

Peel the adhesive sheet

5. Connect the short jig to terminals of flash capacitor to discharge the capacitors.
Note
Be careful not to short-circuit the EVF Slider Assy and the short jig.

Be careful not to short-circuit

the EVF Slider Assy and the
short jig.

(Part code: 1-215-869-11)

DSC-HX90/DSC-HX90V 4-7
Disassembly Places

[2] #247 X 1

Back View

#247

Notes on Assembling the Main Section

Installing the ST-1034 Flexible Board

ST-1034 Flexible Board

Mountain fold
Valley fold

DSC-HX90/DSC-HX90V 4-8
Installing the LC Blind Sheet (LC) (63680)

• Arranging
LC Blind Sheet (LC) (63680)

LF-2123 Flexible Board

• Installing

SY-1056 Board

Routing the cables of SP901

SP901

DSC-HX90/DSC-HX90V 4-9
4-2-3. BT Holder Section

• Refer to “5-2-3. BT Holder Section” on exploded view for Ref. No.

Front Cabinet Section

108 112
109
ns
[1] 111

107

BT901
113
106

Do not touch this part.

(HX90V)
[3] 104
BT900
103 ns
#28 (Note 2)
(Size: 17.0 x 1.7 mm)

105
102
#28

[2] 101 #239

(Note 1)

Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

Note 2
Use this to cut or splice so that it becomes the designated size.

DSC-HX90/DSC-HX90V 4-10
Disassembly Places

[2] #28 X 1 → #239 X 1

#239
Bottom View Back View

#28

[3] #28 X 1

Bottom View
#28

Notes on Assembling the BT Holder

Installing the RL-1042 Board

Upper cabinet block Fitting position

RL-1042 Board

Plate (Rotary Base) Fitting position

Install the RL-1042 Board between the ST Lens Cover (63680)

and the upper cabinet block.

RL-1042 Board
ST Lens Cover (63680)

DSC-HX90/DSC-HX90V 4-11
Installing the FP-2311 Flexible Board

• Arranging

to RL-1042 Board to SY-1056 Board

Mountain fold
Valley fold

FP Flexible Sheet (63680)

• Connecting

FP-2311 Flexible Board

RL-1042 Board

Installing the BT-2007 Flexible Board

Mountain fold
Valley fold

BT-2007 Flexible Board

DSC-HX90/DSC-HX90V 4-12
4-2-4. Front Cabinet Section

• Refer to “5-2-4. Front Cabinet Section” on exploded view for Ref. No.

[3] Upper Cabinet Section

(Boss)

151 [2] #331

#280
152 #247
(Note 1)

[1] 162 (Note 2)

153

154

(Rib) ns

157

156 160
159
(Rib)
155 #310
154

158 #20

(Claw)

ns 161

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

DSC-HX90/DSC-HX90V 4-13
Note 2
Notes on remove the ST Lens Cover (63680)

Peel the RL-1045 Flexible Board.

ST Lens Cover (63680)

(Claws)
(Boss)

Slide and remove the ST Lens Cover (63680).

Disassembly Places

[2] #247 X 1, #280 X 1, #331 X 1

Back View

#280 #331

#247

DSC-HX90/DSC-HX90V 4-14
Notes on Assembling the Front Cabinet

Assembling the lens ring block

1. Put the Manual Ring (63680) on the Manual Ring Retainer (63680).

Manual Ring (63680)

Manual Ring Retainer (63680)

2. Set the Lens Ring (63680) so that its character part faces in the same direction as the XX mark on the Manual
Retainer (63680).
3. Attach the Lens Ring (63680) while aligning its concave with the claw of the Manual Retainer (63680) as shown
in the figure below.

Lens Ring (63680)

XX mark Claw

Manual Retainer (63680),

Manual Ring (63680)

Claws

4. Turn the Manual Retainer (63680) counterclockwise until over the convex of Lens Ring (63680) to attach it.

Convex of Lens Ring (63680)

Lens Ring (63680)

Manual Retainer (63680)

DSC-HX90/DSC-HX90V 4-15
4-2-5. Upper Cabinet Section

• Refer to “5-2-5. Upper Cabinet Section” on exploded view for Ref. No.

(Claws) #239
[1] 221 (Note 1)
{3} 201

#284 #284 {5} 203

(Including LCD902)
(Claw) [2] 222
#239
#284 204 (Note 1)

202 205

212 206
224 225
207

ns

226
(Claw)
[3] 227
{4} 210 209
229
Install
228
231
North pole
228
ns Refer to “Check the
{2} #275 Flash Detection” for
install direction.

{1} 211 230

#275

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

Disassembly Places

Disassembling the EVF block

{1} #275 X 1

Bottom View

#275

DSC-HX90/DSC-HX90V 4-16
{2} #275 X 2

Bottom View

#275

{3} #284 X 3

Left View Front View Right View

#284 #284
#284

Disassembling the flash block

[1] Pop-up the flash unit → #239 X 1

Left View

#239

[2] #239 X 2

Back View

#239

Notes on Assembling the Upper Cabinet Section

Check the Flash Detection

This unit detects flash pop-up or down with the magnet installed in the ST Block Assy. If this magnet (for flash pop-up/
down detection) is incorrectly installed, flash pop-up/down cannot be detected.
After this magnet (for flash pop-up/down detection) is replaced or removed, carry out the following steps to check
operation.

DSC-HX90/DSC-HX90V 4-17
 Magnet
(for flash pop-up/down detection)

1. Turn on the unit. (press the flash down)

2. Set the flash mode to “ Fill-flash”, and check that the “ ” is not appeared on the display.

If “ ” is appeared, the magnet may be installed in an incorrect orientation. Remove the magnet and reinstall it in the
correct orientation, and then recheck operation.

Turn the magnet upside down

Installing the RL-1045 Flexible Board

RL-1045 Flexible Board

Mountain fold
Valley fold

DSC-HX90/DSC-HX90V 4-18
Installing the EVF Unit Assy

EVF Unit Assy

Mountain fold
Valley fold

VF Adhesive Sheet (63680)

Installing the SE-1011 Flexible Board

SE-1011 Flexible Board

Mountain fold
Valley fold

DSC-HX90/DSC-HX90V 4-19
4-2-6. LCD Section

• Refer to “5-2-6. LCD Section” on exploded view for Ref. No.

266
Install direction #239
(Note 1)

LCD901
Red mark

265

257 #239
(Note 1)

256 263
264

255 #27

South pole
266 260
ns
Refer to “Check the Display
Switching Between LCD and
EVF” for install direction.
Install location

261
(Including the
LC-1026 Flexible Board) Black mark
251
259

Install direction

Note 1
This screw can not be reused. Discard the screw removed
once in servicing. Instead, use a new screw.

DSC-HX90/DSC-HX90V 4-20
Notes on Assembling the LCD Section

Check the Display Switching Between LCD and EVF

This unit detects LCD open or close with the magnet installed in the LCD unit. If this magnet (for LCD open/close
detection) is incorrectly installed, LCD open/close cannot be detected.
After this magnet (for LCD open/close detection) is replaced or removed, carry out the following steps to check operation.

LCD901

Magnet
(for LCD open/close detection)

1. Turn on the unit.

2. Pop-up the EVF. Then cover the eyepiece sensor with your finger, and check that the information on the LCD
disappears and then appears on the EVF.

Eyepiece
Sensor

If display switching between LCD and EVF does not occur, the magnet may be installed in an incorrect orientation.
Remove the magnet and reinstall it in the correct orientation, and then recheck operation.

Reverse insertion direction.

DSC-HX90/DSC-HX90V 4-21
4-2-7. Lens Section

• Refer to “5-2-1. Overall Section” on exploded view for Ref. No.

#258

#258

302 (Note 1)
301

303

ns

ns

304

#176

305
ns
306
307

ns
ns 308
ns
311 ns
ns
#258
310
309

Note 1
PRECAUTIONS WHEN HOLDING THE LENS BLOCK

Hold the Lens Block at the Do not hold the following part.
center of both sides.
Zoom Motor
Hold here. *Very weak Connector

Focus Lens
Lens Barrier
Focus Unit *Very weak
*Very weak
*Very weak

DSC-HX90/DSC-HX90V 4-22
4-3. Lens Block

4-3-1. Ornamental Ring A or Barrier Assy Replacing Method

Removal

1. Turn on the power switch and extend the lens (TELE end).
2. Detach the battery.
3. Pour a solvent such as alcohol to two gaps of the Ornamental Ring A with tweezers or a fine-tipped stick as shown
below.
4. Heat the Ornamental Ring A with a drier.
5. Turn the Ornamental Ring A clockwise and counterclockwise to detach it.

Ornamental Ring A

Tweezers Drier
Gaps
Solvent

6. Disengage the four claws and remove the Barrier Assy.

Barrier Assy
Claws

Claws

Installation

1. Fit the four claws and attach the Barrier Assy.

Barrier Assy
Barrier Assy
Claws

Claws

2. Attach two Barrier Tapes so that the end of each tape comes to the dent.
Note
Attach Barrier Tapes carefully so that they do not wrinkle.

DSC-HX90/DSC-HX90V 4-23
3. Attach the Ornamental Ring A and push it gently.

Barrier Tapes Ornamental Ring A

Barrier Tapes

DSC-HX90/DSC-HX90V 4-24
4-3-2. 2 Group Frame Block Assy Replacing Method

Removal

1. Remove the LF-2123 Flexible Board from the claw.

2. Remove the SS Flexible Board from the connector of the LF-2123 Flexible Board.
3. Remove the LF-2123 Flexible Board from the groove, the hole and the claw.

Groove Claw
LF-2123 Flexible Board

Claw

SS Flexible Board
Hole Connector

4. Remove the five screws.

5. Remove the FG Retainer.
6. Remove the Z Retainer.

Screws

Screws

FG Retainer

Z Retainer

7. Remove the two FG Sensors and a Reset Sensor on the LF-2123 Flexible Board.

FG Sensors

Reset Sensor

8. Remove the LF-2123 Flexible Board from the two bosses.

9. Remove the Flexible Board of Rear Lens Assy from the connector for F Flexible Board of LF-2123 Flexible
Board.

DSC-HX90/DSC-HX90V 4-25
10. Remove the Rear Lens Assy.

Connector for F Flexible Board of

LF-2123 Flexible Board

F Flexible Board of
Rear Lens Assy

Rear Lens Assy

Bosses

LF-2123 Flexible Board

11. Unsolder the DC Motor Worm Assy and lands for motor of LF-2123 Flexible Board.

LF-2123 Flexible Board

DC Motor Worm Assy

Solders

12. Remove the two screws from the DC Motor Worm Assy.

DSC-HX90/DSC-HX90V 4-26
13. Remove in order of the Gear D, Gear B/C, Worm Wheel and Gear A.

Gear D

Gear B/C

Worm Wheel
DC Motor Worm Assy
Gear A

Screws

14. Insert the Gear D and rotate it clockwise to full extend the lens.

Gear D

Gear D

Extend

15. Remove the SS Flexible Board from the lens block as shown in the figure below.

SS Flexible Board
SS Flexible Board Pull out the SS Flexible
Board from this hole.

Hole

Claw

DSC-HX90/DSC-HX90V 4-27
16. Rotate the Gear D counterclockwise to full shrink the lens.

Gear D

Shrink

17. Remove the 3 Group Frame Block Assy from the Fixed Barrel Core Unit_1.

SS Flexible Board

3 Group Frame Block Assy

Fixed Barrel
Core Unit_1

DSC-HX90/DSC-HX90V 4-28
18. Remove the Core Unit_1 from the Fixed Barrel.

Core Unit_1

Fixed Barrel

19. Remove the Core Unit_2 from the Drive Gear Barrel Assy.

Core Unit_2

Triangle mark

Drive Gear Barrel Assy Concave

20. Rotate the Linear Motion Cam Barrel in the direction of the arrow and remove it from the Drive Gear Barrel
Assy.

Linear Motion Linear Motion

Cam Barrel Cam Barrel

Drive Gear
Barrel Assy

21. Rotate the rear edge of Core Unit_3 clockwise to extend the lens.

DSC-HX90/DSC-HX90V 4-29
22. Remove the Barrier Ring and the Barrier Assy.
Note
Refer to “Removal” for removing the Barrier Ring and Barrier Assy.

Barrier Ring

Barrier Assy

Core Unit_2

Rear edge of
Core Unit_3

23. Remove the Core Unit_3 from the Front Assy.

Front Assy

Core Unit_3

DSC-HX90/DSC-HX90V 4-30
24. Rotate the rear edge of Barrier Frame in the direction of the arrow and remove the Linear Guide Barrel_A.

Linear Guide Barrel_A

1 Group Frame
Block Assy
Linear Guide Barrel_A Rear edge of
Barrier Frame

25. Remove the Barrier Frame from the 1 Group Frame Block Assy.

Barrier Frame

1 Group Frame
Block Assy

26. Rotate the Linear Guide Barrel_B clockwise and remove the Cam Barrel.

Linear Guide Barrel_B

Linear Guide Barrel_B

Cam Barrel
Cam Barrel

27. Remove the two 2G Springs from the hooks of 2 Group Frame Block Assy by tweezers.

DSC-HX90/DSC-HX90V 4-31
28. Remove the 2 Group Frame Block Assy from the Linear Guide Barrel_B.

2 Group Frame Block Assy

Hook
Tweezers

Hook

2G Springs
Linear Guide Barrel_B

Installation

1. Match the cabinet number of Linear Guide Barrel_B and the cabinet number of 2 Group Frame Block Assy, and
match the three vertical grooves of Linear Guide Barrel_B and the three projections of 2 Group Frame Block Assy
and assemble them.
2. Lift up the 2 Group Frame Block Assy so that the two hooks can be seen.
3. Attach the two 2G Springs to the 2 Group Frame Block Assy by tweezers.

2 Group Frame Block Assy

Projection Projections
Hook
Tweezers

Hook

2G Springs
Cabinet number
Vertical
grooves
Vertical
groove

Linear Guide Barrel_B

Cabinet number

4. Match the two grooves near the cabinet number of Cam Barrel and the two hooks near the cabinet number of Linear
Guide Barrel_B and assemble them.

DSC-HX90/DSC-HX90V 4-32
5. Assemble Linear Guide Barrel_B to the Cam Barrel by rotating itself counterclockwise.

Linear Guide Barrel_B

Linear Guide
Barrel_B

Hooks
Cabinet number

Cam Barrel

Grooves

Cam Barrel

Cabinet number

6. Match the Groove near the white part of 1 Group Frame Block Assy and the boss near the Triangle mark of Barrier
Frame and assemble them.
7. Position the 1 Group Frame Block Assy so that the convex of 1 Group Frame Block Assy is matched to the convex
(right of three places) of Barrier Frame.

Barrier Frame

Barrier Frame

Triangle
mark

Boss

1 Group Frame
Block Assy

Groove

Three square marks

Convex
White part
1 Group Frame
Block Assy 1 Group Frame
Block Assy

DSC-HX90/DSC-HX90V 4-33
8. In the state of previous step, match the convex of 1 Group Frame Block Assy and the concave of the Linear Guide
Barrel_A and assemble them.

Cabinet number

Linear Guide Barrel_A

Concave

1 Group Frame
Block Assy

Convex position set

9. Rotate the rear edge of Barrier Frame in the direction of the arrow and extend the Barrier Frame.

Linear Guide Barrel_A

Barrier Frame

Linear Guide Barrel_A Rear edge of

Barrier Frame

10. Match the Concave of Front Assy and Triangle mark of Core Unit_3 and assemble them.

Front Assy

Concave

Core Unit_3

Triangle mark

DSC-HX90/DSC-HX90V 4-34
11. Attach in order of Barrier Assy, Barrier Tape and Barrier Ring.
Note
Refer to “Installation” for assembling the Barrier Ring and Barrier Assy.

12. Make a state of the Core Unit_2 by rotating the Rear edge of Core Unit_3 counterclockwise.

Barrier Ring

Barrier Tapes

Core Unit_2

Barrier Assy

Rear edge of
Core Unit_3

13. Match the Diamond mark of Linear Motion Cam Barrel and the concave of Drive Gear Barrel Assy and assemble
them.
14. Rotate the Linear Motion Cam Barrel in the direction of arrow so that the concave of Drive Gear Barrel Assy is
matched to the diamond mark of the Linear Motion Cam Barrel.

Linear Motion
Cam Barrel
Diamond mark

Drive Gear
Barrel Assy Concave
Match the concave of the Drive Gear Barrel Assy with
the diamond mark of the Linear Motion Cam Barrel.

DSC-HX90/DSC-HX90V 4-35
15. Match the Concave of Drive Gear Barrel Assy and the triangle mark of the Core Unit_2 and assemble them.

Core Unit_2

Triangle mark

Drive Gear Barrel Assy Match the diamond mark of Drive Gear
Concave
Barrel Assy and triangle mark of Core Unit_2

16. Match the semicircular cutout of Core Unit_1 and Gear D mounting portion of Fixed Barrel and assemble them.

Core Unit_1
Semicircular cutout

Fixed Barrel

Match the semicircular cutout of Core Unit_1

and Gear D mounting portion of Fixed Barrel.

Gear D mounting
portion

DSC-HX90/DSC-HX90V 4-36
17. Match the SS Flexible Board of 3 Group Frame Block Assy and the hole of the Fixed Barrel Core Unit_1 and
assemble them.

SS Flexible Board

3 Group Frame Block Assy

Fixed Barrel Hole for SS Flexible Board.

Core Unit_1

18. Insert the Gear D and rotate it clockwise to full extend the lens.

Gear D

Extend

19. Put the SS Flexible Board through the hole.

SS Flexible board

Hole

DSC-HX90/DSC-HX90V 4-37
20. Remove the Gear D.

Gear D

21. Attach in order Gear A, Worm Wheel, Gear B/C and Gear D.
22. Match the DC Motor Worm Assy to the boss and attach it with two screws.

Gear D

Gear B/C Hole

Boss
Worm Wheel

Gear A

DC Motor Worm Assy

Screws

DSC-HX90/DSC-HX90V 4-38
23. Solder the DC Motor Worm Assy and the LF-2123 Flexible Board.

LF-2123 Flexible Board

DC Motor Worm Assy

Solders

24. Assemble the Rear Lens Assy. At that time, the LF-2123 Flexible Board must come on the Rear Lens Assy.
25. Insert the F Flexible Board of the Rear Lens Assy to the connector for F Flexible Board of the LF-2123 Flexible
Board.

DSC-HX90/DSC-HX90V 4-39
26. Tuck it in inward as shown, at that time, attach the LF-2123 Flexible Board to the two bosses.

Rear Lens Assy Connector for F Flexible Board

of LF-2123 Flexible Board

F Flexible Board of
Rear Lens Assy

LF-2123
Flexible Board

Bosses

DSC-HX90/DSC-HX90V 4-40
27. Attach the two FG sensors and a Reset Sensor on the LF-2123 Flexible Board.

FG Sensors

Reset Sensor

28. Attach the claw of Z Retainer by matching the groove.

29. Attach the two claws of FG Retainer by matching groove and claw.
30. Attach the five screws.

Screws

Groove

Screws
Groove

Claws
Z Retainer

Claw

FG Retainer
Claw

DSC-HX90/DSC-HX90V 4-41
31. Attach the LF-2123 Flexible Board to the lens block, and connect the LF-2123 Flexible Board and SS Flexible
Board as shown in the figure below.

Groove Claw
LF-2123 Flexible Board

Claw

SS Flexible Board
Hole Connector

SS Flexible Board

Hole

Claw

32. Shrink the lens by applying 4.5V DC to the DC Motor Worm Assy.

Shrink

DC Motor Worm Assy

DC4.5V

DSC-HX90/DSC-HX90V 4-42
 Section 5
Repair Parts List

5-1. Note on Repair Parts

(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some The components identified by mark or dotted line with
differences from the original one. mark are critical for safety.
• Items marked “*” are not stocked since they are seldom Replace only with part number specified.
required for routine service. Some delay should be anticipated
Les composants identifiés par une marque sont
when ordering these items.
critiques pour la sécurité.
• The mechanical parts with no reference number in the
Ne les remplacer que par une pièce portant le numéro
exploded views are not supplied.
spécifié.
• Due to standardization, replacements in the parts list may be
different from the parts specified in the diagrams or the
components used on the set. CAUTION
• ns: Not supplied part. Danger of explosion if battery is incorrectly replaced.
• CAPACITORS: Replace only with the same or equivalent type.
uF: μF Dispose of used batteries according to the instructions.
• COILS
uH: μH ⌞ᝅ
• RESISTORS
ྲ᷌⭥⊐ᴤᦒнᖃՊᴹ⠶⛨ড䲙DŽ
All resistors are in ohms.
ਚ㜭⭘਼ṧ㊫රᡆㅹ᭸㊫රⲴ⭥⊐ᶕᴤᦒDŽ
METAL: metal-film resistor
࣑ᗵ᤹➗䈤᰾༴㖞⭘ᆼⲴ⭥⊐DŽ
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable • Color Indication of Appearance Parts
• SEMICONDUCTORS Example:
In each case, u: μ, for example: (SILVER) : Cabinet’s Color
uA... : μA... , uPA... : μPA... , uPB... : μPB... , (Silver) : Parts Color
uPC... : μPC... , uPD... : μPD...

(JAPANESE)
• -XX, -X ,

• *
• , ,

• ns:
• uF μF
• Ω

• uH μH
• uA..., uPA..., uPB..., uPC..., uPD...
μA..., μPA..., μPB..., μPC..., μPD...

DSC-HX90/DSC-HX90V 5-1
5-2. Exploded View

Overall Section

[5] LCD Section

#247
(Note 1)
1
[4] 4 (Claws)

[2] 2
(Claw)
(Note 2)

#239
(Note 1)
#247
(Note 1)

3
(Claws)

#239
(Note 1)
#239
Main Section (Note 1)

(Claws)

9 #247
(Claw)
(Note 1)
8 6
(Claws) [3] 5 (Note 2)
#247
(Note 1)
[1] 7

Ref. No.
or Q'ty Part No. SP Description

1 A-2078-583-A LID, MULTI (63680) BK (SERVICE)

2 A-2078-579-A CABINET REAR (63680) BK SERVICE
3 4-534-395-01 SHEET (WIFI), ADHESIVE
4 1-493-023-11 CONTROL SWITCH BLOCK (SW63680)
5 A-2075-232-A CABINET SIDE BLOCK ASSY (HX90V)

5 A-2075-233-A CABINET SIDE BLOCK ASSY (HX90)

6 4-489-010-01 SHEET (ANT), ADHESIVE
7 4-570-287-01 BOTTOM (63680), CABINET
8 4-573-657-01 BOTTOM (63680), SHEET CABINET
9 4-576-900-01 BOTTOM (B)(63680), SHEET CABINET

#239 4-287-435-11 SCREW (M1.4 EUROPE) TYPE

#247 4-412-769-11 SCREW (M1.4), NEW TRU-STAR, P2

DSC-HX90/DSC-HX90V 5-2
Main Section

[1] ns
(Hook)
BT Holder Section

[2] 56
(Claw)

57
#247 58
(Note 1)
SP901

61

62 (Note 2)
(Size 4.4 x 4.4 mm) 55

54
60

Refer to
“High-voltage Cautions”
C902
64
53 53

Refer to
[3] Lens Section
(Note 3)
C901 “High-voltage Cautions”

52 51

Ref. No.
or Q'ty Part No. SP Description

51 4-570-300-01 SHEET (LOWER) A (63680)

52 4-570-301-01 SHEET (LOWER) B (63680)
53 4-570-302-01 SHEET (UPPER)(63680)
54 A-2079-995-A SERVICE, NFC INDIVIDUAL
55 A-2075-313-A ST-1034 FLEXIBLE BOARD, COMPLETE

56 A-2075-481-A SY-1056 BOARD, COMPLETE (SERV-

ICE) (HX90V)
56 A-2075-482-A SY-1056 BOARD, COMPLETE (SERV-
ICE) (HX90)
57 4-570-298-01 INSULATING SHEET (SY)(63680)
58 4-571-217-01 SHEET (63680), HDMI
60 4-572-805-01 CUSHION (63680), ES SWITCH

61 4-570-306-01 SHEET (LE)(63680), LC BLIND

62 4-441-672-01 SHEET, ADHESIVE
64 4-570-224-01 SHEET (LC)(63680), LC BLIND
C901 1-118-631-11 CAP, ALUMINIUM ELECT 31uF 330V
C902 1-120-098-11 CAP, ALUMINIUM ELECT 21uF 330V

SP901 1-858-904-41 LOUD SPEAKER (0.8CM)

#247 4-412-769-11 SCREW (M1.4), NEW TRU-STAR, P2

DSC-HX90/DSC-HX90V 5-3
BT Holder Section

Front Cabinet Section

108 112
109
ns
[1] 111

107

BT901
113
106

Do not touch this part.

(HX90V)
[3] 104
BT900
103 ns
#28 (Note 2)
(Size: 17.0 x 1.7 mm)

105
102
#28

[2] 101 #239

(Note 1)

Note 2

POLYESTER TAPE (BLACK) 4MM (9-913-210-04) also can

be used as a service part.

Ref. No.
or Q'ty Part No. SP Description

101 4-570-294-01 SHEET METAL (63680), GPS GROUND

102 4-570-310-01 CUSHION (63680), AF
103 9-913-210-03 POLYESTER TAPE (BLACK) 10MM
(Note 2)
104 A-2079-982-A RL-1042 BOARD, COMPLETE (SERV-
ICE) (HX90V)
104 A-2075-320-A RL-1042 BOARD, COMPLETE (HX90)

105 1-894-564-11 FP-2311 FLEXIBLE BOARD

106 4-570-296-01 PLATE (ROTARY BASE) (63680)
107 4-571-220-01 GASKET (63680), RADIATION
108 4-570-307-01 SHEET, AF LIGHT INTERCEPTION
109 4-570-292-01 WINDOW (63680), AF

111 A-2078-538-A BTH BLOCK ASSY (680) BK SERVICE

112 4-570-309-01 SHEET (63680), STRAP BLIND
113 1-888-407-11 BT-2007 FLEXIBLE BOARD
BT900 1-756-710-14 LITHIUM RECHARGEABLE BATTERY
BT901 1-780-826-11 * TERMINAL BOARD, BATTERY

#28 3-348-998-61 SCREW (M1.4X4), TAPPING, PAN

#239 4-287-435-11 SCREW (M1.4 EUROPE) TYPE

DSC-HX90/DSC-HX90V 5-4
Front Cabinet Section

[3] Upper Cabinet Section

(Boss)

151 [2] #331

#280
152 #247
(Note 1)

[1] 162 (Note 2)

153

154

(Rib) ns

157

156 160
159
(Rib)
155 #310
154

158 #20

(Claw)

ns 161

Ref. No.
or Q'ty Part No. SP Description

151 A-2078-575-A RETAINER, MANUAL RING SERVICE

152 A-2078-576-A RING, MANUAL (63680) (SERVICE)
153 A-2078-574-A LENS RING BLOCK ASSY SERVICE
154 4-570-280-01 STOPPER (63680), RING RETAINER
155 4-570-305-01 RING (63680), FIXED SHEET LENS

156 4-570-308-02 SHEET (63680), PR SENSOR

157 4-571-219-01 SHEET (63680), RADIATION
158 A-2078-586-A CABINET FRONT (63680) (SERVICE)
159 4-570-286-01 SHEET (GRIP) (63680), ADHESIVE
160 4-570-276-01 GRIP (63680)

161 4-571-218-01 SHEET (63680), HARNESS

162 4-570-288-01 COVER (63680), ST LENS
#20 2-635-591-31 SCREW (M1.4), NEW TRUSTAR, P2
#247 4-412-769-11 SCREW (M1.4), NEW TRU-STAR, P2
#280 4-437-538-11 SPECIAL (M1.4 (D2.75))

#310 4-300-115-31 TAPPING (1.7) (CH)

#331 4-536-370-01 SCREW, 0+P2 1.4 POWERLOK

DSC-HX90/DSC-HX90V 5-5
Upper Cabinet Section

(Claws) #239
[1] 221 (Note 1)
{3} 201

#284 #284 {5} 203

(Including LCD902)
(Claw) [2] 222
#239
#284 204 (Note 1)

202 205

212 206
224 225
207

ns

226
(Claw)
[3] 227
{4} 210 209
229
Install
228
231
North pole
228
ns Refer to “Check the
{2} #275 Flash Detection” for
install direction.

{1} 211 230

#275

Ref. No.
or Q'ty Part No. SP Description

201 4-570-255-01 CABINET (63680), VF

202 4-571-198-01 STICKER (63680), PULL
203 A-2078-543-A EVF UNIT (SERVICE)
204 4-570-264-01 COVER (63680), ES
205 4-570-263-01 LENS (63680), ES

206 4-570-261-01 CUSHION (63680), ES

207 A-2075-314-A SE-1011 FLEXIBLE BOARD, COMPLETE
209 4-570-257-01 SHEET METAL (63680), EV GROUND
210 X-2591-441-1 SLIDER ASSY (63680), VF
211 A-2075-310-A EV-1013 BOARD, COMPLETE

212 4-570-901-01 SHEET (63680), VF ADHESIVE

221 4-570-176-01 COVER (63680), ST
222 A-2075-214-A CABINET UPPER BLOCK ASSY 63680
224 4-570-303-01 RUBBER (63680), MICROPHONE
225 4-570-304-01 SHEET (63680), HALL SENSOR

226 A-2075-312-B RL-1045 FLEXIBLE BOARD, COMPLETE

227 A-2078-578-A ST BLOCK ASSY (63680) SERVICE
228 4-573-570-02 SHEET (63680), ST COVER
229 1-492-922-11 FLASH UNIT
230 4-534-040-01 CUSHION, MICROPHONE

231 1-471-682-11 MAGNET

#239 4-287-435-11 SCREW (M1.4 EUROPE) TYPE
#275 4-433-882-11 TAPPING (1.4) (ECOLOGY)
#284 4-433-882-21 TAPPING (1.4) (ECOLOGY)

DSC-HX90/DSC-HX90V 5-6
LCD Section

266
Install direction #239
(Note 1)

LCD901
Red mark

265

257 #239
(Note 1)

256 263
264

255 #27

South pole
266 260
ns
Refer to “Check the Display
Switching Between LCD and
EVF” for install direction.
Install location

261
(Including the
LC-1026 Flexible Board) Black mark
251
259

Install direction

Ref. No.
or Q'ty Part No. SP Description

251 1-471-549-11 * MAGNET (ND7.9X2.9X1.2)

255 1-893-251-11 FPC-2010 FLEXIBLE BOARD
256 X-2591-439-1 FRAME ASSY (63680), MAIN
257 4-570-222-01 CABINET (R) (63680), VF
259 4-570-223-01 SHEET (63680), FRAME

260 4-570-217-01 INSULATING SHEET (63680), LC

261 A-2082-763-A LCD BLOCK ASSY (SERVICE)
263 4-572-807-01 SHEET (63680), VF LOW REF
264 1-471-682-11 MAGNET
265 1-471-678-11 MAGNET

266 4-570-224-01 SHEET (LC) (63680), LC BLIND

LCD901 A-2078-551-A LCD BLOCK ASSY (680) SERVICE
(HX90V)
LCD901 A-2078-552-A LCD BLOCK ASSY (671) SERVICE
(HX90)
#27 2-662-396-11 SCREW (M1.4), NEW, TRUSTAR, P2
#239 4-287-435-11 SCREW (M1.4 EUROPE) TYPE

DSC-HX90/DSC-HX90V 5-7
Lens Section

#258

#258

302 (Note 1)
301

303

ns

ns

304

#176

305
ns
306
307

ns
ns 308
ns
311 ns
ns
#258
310
309

Ref. No.
or Q'ty Part No. SP Description

301 A-1940-465-A CD-1005 FLEXIBLE BOARD, COMPLETE

302 8-848-924-01 LSV-1810A-BK
303 A-2070-463-A LF-2123 FLEXIBLE BOARD, COMPLETE
304 A-2069-337-A LUBRICATING BLOCK ASSY, (D)
305 A-2069-335-A LUBRICATING BLOCK ASSY, GEAR

306 A-2069-333-A LUBRICATING BLOCK ASSY, WHEEL

307 A-2069-334-A LUBRICATING BLOCK ASSY, (A)
308 A-2069-322-A WORM BLOCK ASSY, DC MOTOR
309 4-565-209-01 RING (A), ORNAMENTAL
310 A-2069-338-A BARRIER BLOCK ASSY (1810A-BK)

311 4-451-090-01 BARRIER TAPE

#176 3-947-504-31 SCREW (M1.2)
#258 4-299-468-11 SCREW, TAPPING UB1.2 (CH)

DSC-HX90/DSC-HX90V 5-8
5-3. Fuse

SY-1056 BOARD (SIDE B)

4.2 V
F3
F1

F4
5.0 V Primary side

F2

4.2 V

RL-1042 BOARD (SIDE B)

4.2 V
F5

SY-1056 Board
Ref. No.
or Q'ty Part No. SP Description

F1 1-523-373-11 FUSE (2A/24V)

F2 1-523-366-11 FUSE (0.63A/24V)
F3 1-523-368-11 FUSE (0.8A/24V)
F4 1-523-373-11 FUSE (2A/24V)

RL-1042 Board
Ref. No.
or Q'ty Part No. SP Description

F5 1-523-366-11 FUSE (0.63A/24V)

DSC-HX90/DSC-HX90V 5-9
5-4. Accessories

901 902 904 905 906

Ref. No.
or Q'ty Part No. SP Description

901 1-490-498-63 AC Adaptor AC-UB10C (IN5)

901 1-492-868-11 AC Adaptor AC-UB10C/UB10D (U2,
CA2)
901 1-492-868-21 AC Adaptor AC-UB10C/UB10D (CN1)
901 1-492-868-31 AC Adaptor AC-UB10C/UB10D (J1)
901 1-492-868-42 AC Adaptor AC-UB10C/UB10D (EX-
CEPT U2, CA2, CN1, J1, IN5)

902 1-837-421-13 Power Cord (mains lead) (CEH,

HK1, EA8)
902 1-837-424-11 Power Cord (mains lead) (TW6)
902 1-837-427-11 Power Cord (mains lead) (CE3,
RU3, E32)
902 1-837-428-12 Power Cord (mains lead) (KR2)
902 1-837-429-11 Power Cord (mains lead) (AU2)

902 1-848-142-11 Power Cord (mains lead) (IN5)

904 1-846-615-12 Micro USB Cable
905 4-470-899-11 Wrist Strap
906 4-572-610-01 * Instruction Manual (JAPANESE)
906 4-572-610-11 * Instruction Manual (ENGLISH)

906 4-572-610-21 * Instruction Manual (FRENCH)

906 4-572-610-31 * Instruction Manual (SPANISH)
906 4-572-610-41 * Instruction Manual (GERMAN,
DUTCH, SWEDISH, ITALIAN, PORTU-
GUESE, DANISH, FINNISH, NORWE-
GIAN, POLISH, CZECH, HUNGARIAN,
SLOVAK)
906 4-572-610-61 * Instruction Manual (RUSSIAN, UK-
RAINIAN)
906 4-572-610-71 * Instruction Manual (KOREAN)

906 4-572-610-81 * Instruction Manual (SIMPLIFIED

CHINESE)
906 4-572-610-91 * Instruction Manual (TRADITIONAL
CHINESE)
906 4-572-611-11 * Instruction Manual (ARABIC, PER-
SIAN)
906 4-572-611-21 * Instruction Manual (TURKISH,
THAI, INDONESIAN)

Ref. No.
or Q'ty Part No. SP Description

8-022-359-00 Rechargeable Battery Pack NP-

BX1/J (J1)
8-022-359-31 Rechargeable Battery Pack NP-
BX1/UC (U2, CA2)
8-022-359-50 Rechargeable Battery Pack NP-
BX1/CE (EXCEPT U2, CA2, CN1, J1)
8-022-359-71 Rechargeable Battery Pack NP-
BX1/CN (CN1)

DSC-HX90/DSC-HX90V 5-10
 Section 6
Frame Schematic Diagrams
Frame Wiring

ANT901
(NFC ANTENNA)

S0001
(EVF POP-UP) C901, 902
RL-1042 BOARD (SIDE A)
EV-1013 BOARD (CHARGING CAPACITOR)
(SIDE B) C902 LC-1026 FLEXIBLE BOARD
39
S0005
39
38

S0004 ON/OFF
C901 (MODE DIAL)
2
1

1
CN3001 1 39

ST-1034 S0003 ANT403

FLEXIBLE BOARD CN1001
SHUTTER,
RL-1045 FLEXIBLE BOARD
GPS

14
FLASH ZOOM ANTENNA
EV-1013 BOARD SE-1011 FLEXIBLE BOARD UNIT
(SIDE A) 6
HX90V

1
1
RL-1042 BOARD (SIDE B)
6 1
CN3002 1

1
CN0005
2 CN3003 50
1 51 LCD901

16
(LCD MODULE) 39 1 16

2
CN0004
38 2
MIC001

CN8041
COLOR
3.0 INCH (MICROPHONE)(R)
EVF UNIT
COLOR
LCD902 LCD
1 39

MIC002

54
55
(MICROPHONE)(L)

LCD BACKLIGHT CN8040

51 1

4 1
FP-2311
FLEXIBLE
BOARD

10

SY-1056 BOARD BT901

BT-2007 FLEXIBLE SY-1056 BOARD
39 1
(SIDE B) BATTERY S
BOARD 1 (SIDE A)
TERMINAL
39 1 CN4001

15
1
2

39 1

5
MULTI 10 1
38 2
CN4112

CN4114 1 CN4109 38 CN4115 2

6
CD-1005 FLEXIBLE BOARD
50

ET7381
51

51 BT900
29 1 26 30
1

(LITHIUM BATTERY)
2

LENS BLOCK
CN4100

WIRELESS LAN
ANTENNA CN7100
50
51

1 FPC-2010
FLEXIBLE BOARD
CN4110

SE7701
8

(PITCH/YAW) 28 27
CN6801 38
1

2
19 1
1 39
18 2 RED SP901
BLK (SPEAKER)
CONTROL
SWITCH CN9000
BLOCK
(SW63680)

DSC-HX90/DSC-HX90V 6-1
 Revision History

Ver. Date History Contents S.M. Rev.

issued
1.0 2015.05 Official Release ― ―
1.1 2015.07 Revised-1 • Addition of IN5 model. Yes
(A1 15-053) • Revision of "Replacement of Main Parts" and
"Repair Parts List".

DSC-HX90/DSC-HX90V 3
DSC-HX90 (CE3)
DSC-HX90 (CEH)
DSC-HX90 (RU3)
DSC-HX90 (CN1)
DSC-HX90V (U2)
DSC-HX90V (CA2)
DSC-HX90V (CE3)
DSC-HX90V (CEH)
DSC-HX90V (E32)
DSC-HX90V (IN5)
DSC-HX90V (AU2)
DSC-HX90V (EA8)
DSC-HX90V (TW6)
DSC-HX90V (HK1)
DSC-HX90V (KR2) Printed in Japan
DSC-HX90V (J1) Sony Corporation 2015. 07 08
9-896-735-12 © 2015