Formulation Additives

Technical Data Sheet

Foamaster MO NXZ NC
(old: Foamaster NXZ)

Product Description Liquid defoamer for emulsion paints and adhesive systems.

Chemical Composition Formulation based on hydrocarbons and non ionic surfactants.

Properties
Typical Properties Density, 25° C ~ 0.85 – 0.90 g/ml
(ISO 2811-3)
Brookfield Viscosity, 25° C ~ 100 – 800 mPa s
(RV spindle 3, 50 rpm)
(ISO 2555)
Water content ~ 0.0 – 0.5 %
(ISO 4317)

Typical Characteristics Appearance cloudy amber liquid

These typical values should not be interpreted as specifications.

Applications
Foamaster® MO NXZ NC is a defoamer for emulsion paints based on styrene-butadiene, acrylic,
polyvinyl chloride and its copolymers, ethylene vinyl acetate, vinylidene chloride and water-soluble
alkyds.

Dosage In paint formulations 0.2 - 0.5% Foamaster® MO NXZ NC, calculated on total formulation, is
recommended. For adhesives 0.5 - 1% Foamaster® MO NXZ NC based on the weight of the latex
solids is generally adequate. Foamaster® MO NXZ NC may be incorporated as supplied or
dispersed in water prior to use. In paint manufacturing, it is usually advantageous to split the
addition of the defoamer. Add half the normal amount to the pigment mix prior to grinding to
suppress formation of foam. Add the remainder to the let-down portion of the paint.

Safety
General The usual safety precautions when handling chemicals must be observed. These include the
measures described in Federal, State, and Local health and safety regulations, thorough ventilation
of the workplace, good skin care, and wearing of protective goggles.

Material Safety Data Sheet All safety information is provided in the Material Safety Data Sheet for Foamaster® MO NXZ NC.

June 2015 Rev 2 Page 1 of 2

 Storage
Foamaster® MO NXZ NC is subject to appropriate storage under the usual storage and temperature
conditions, our products are durable for at least 1 year. After prolonged storage, a slight
sedimentation may occur. This does not change the characteristics of the product. It is recommended
to homogenize Foamaster® MO NXZ NC prior to use. Foamaster® MO NXZ NC properties are not
affected by freezing. If subjected to low temperatures, allow to warm to room temperature and mix
well before using.

Important
While the descriptions, designs, data and information contained herein are presented in good faith
and believed to be accurate, they are provided for guidance only. Because many factors may affect
processing or application/use, BASF recommends that the reader make tests to determine the
suitability of a product for a particular purpose prior to use. NO WARRANTIES OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING
PRODUCTS DESCRIBED OR DESIGNS, DATA OR INFORMATION SET FORTH, OR THAT THE
PRODUCTS, DESCRIPTIONS, DESIGNS, DATA OR INFORMATION MAY BE USED WITHOUT
INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. In no case shall the
descriptions, information, data or designs provided be considered a part of BASF's terms and
conditions of sale. Further, the descriptions, designs, data, and information furnished by BASF
hereunder are given gratis and BASF assumes no obligation or liability for the descriptions, designs,
data or information given or results obtained all such being given and accepted at the reader's risk.

Foamaster is a registered trademark of BASF Group.

© BASF Corporation, 2015

BASF Corporation is fully committed to the Responsible Care®

initiative in the USA, Canada, and Mexico.
For more information on Responsible Care® go to:
U.S.: www.basf.us/responsiblecare_usa
Canada: www.basf.us/responsiblecare_canada
México: www.basf.us/responsiblecare_mexico

BASF Corporation
Dispersions and Pigments
11501 Steele Creek Road
Charlotte, North Carolina 28273
Phone: (800) 251 – 0612
Email: [email protected]
www.basf.us/dpsolutions

June 2015 Rev 2 Page 2 of 2