Block B310 WB
Cold Applied Bitumen Emulsion
WATERPROOFING SOLUTIONS
FOUNDATIONS &BASEMENT
Ready to use
Cold applied, easy to apply
Applicable on a variety of substrates
Flexible and joint free
Good resistance against chloride and
sulphate ions
Can be used as curing membrane to
newly placedconcrete
_
PRODUCT DESCRIPTION
Block B310 WB is a cold applied water based bitumen
with special additives. It is a blend of selected bitumen
emulsified with water to give an easily applied protective
coating. It dries to form a black flexible coating.
TECHNICAL DATA
Colour Dark brown, dries to black
APPLICATION AREAS
Specific Gravity 0.90
General Waterproofing and protective coating
Solids content
for concrete, masonry, screed, metal surfaces 35%
etc.
Recoat time 3 hours @ 35°C
Protective coating on concrete foundations
Curing compound / sealer for the concrete before Application temperature 5°C to 45°C
applying the top finishing coats Viscosity at 25 °C 1000 – 4000 CPS
Vapor proof barrier coating
Flash point Non flammable
Technical data are approximately provided according to a
temperature of + 23°C and a relative humidity of 50%.
Block B310 WB 1
FEATURES APPLICATION
Flexible after curing. Stir the contents of the drum thoroughly before
Resistant to crack formations on the application application to remove all sediments.
surface; seamless Depending on the dry film thickness required, apply
Applicable easily with a brush and roller. the rubberized bitumen coating @ 4 - 6m²/ltr coat on
Resistant to the usual loads on the ground. vertical areas, it is recommended to apply the coating
Suitable for use in all kinds of mineral-based in multiple layers in order to avoid sagging of the
surfaces, stone and stone-derivative bricks, pumice heavy bodied coating.
brick, briquette, aerated concrete, concrete block, Subsequent coats shall be applied only after the
limestone, etc. built plastered surfaces, cement- previous coat dries off completely and shall be
based plastered surfaces, grout and concrete applied at right angles to the previous coat.
surfaces. Clean dry sand may be broadcasted onto the wet
coating to provide a key for the subsequent coats and
achieve a greater dry film thickness.
PREPARATION OF THE SUBSTRATE The coating should be applied and finished up to the
DPC level.
The surfaces to be coated should be free of adhesive Care shall be taken to ensure that the first coat is not
preventive foreign substances such as dust, dirt, mould punctured during the application of the second coat.
oil, paint etc.; residues and wastes like cement, plaster However if the coating is damaged the area can be
and concrete should also be removed. readily over coated with proper surface preparation.
The sub-surfaces that are not strong enough to carry
themselves e.g. cracked plasters, weak surfaces, or
residues of moss should be cleaned from the
application surface. The application surface must EQUIPMENT CLEANING
definitely be crack-free, stable and strong. The gaps
should be filled with Bostik Reno C412 Repair HP.
Clean all tools immediately after use with water.
Residues of bitumen-based waterproofing materials
Hardened material can be cleaned with a solvent.
should be removed from the surface prior to
application.
The joints with 2-5mm gaps should be filled with fine
plaster prior to application.
Air bubbles formation, which may occur due to gaps
and pores, should be prevented during the process.
Corners should be rounded.
It is highly recommended to apply a priming coat
prior to the application of the BOSTIK BLOCK B310 WB
coating on the substrate. The primer can be prepared
in the site by diluting BOSTIK BLOCK B310 WB with
20% of water and apply this diluted coat as the primer.
For very dry and porous substrates apply two coats of
this primer. The primer can be applied to damp or
freshly cast concrete surfaces also.
Block B310 WB 2
FOUNDATIONS &BASEMENT
COVERAGE
The coverage varies depending on the type of use:
General use – 2 - 4m2/ltr/coat
Metallic surface – 4 - 6m2/ltr/coat
PACKAGING
_
BOSTIK BLOCK B310 WB is supplied in 15 ltr Pail and
200 ltr Drum.
STORAGE
They should be protected for water, frost and
adverse weather conditions.
They should be kept dry and cool on wooden pallets.
The torn and opened products should be closed
immediately and consumed first.
Maximum 3 buckets should be stocked on each other.
Shelf life is maximum 12 months conditional to
complying with the abovementioned storage
conditions.
The information given and recommendations made herein are based on
Bostik’s research only and are not guaranteed to be accurate. The
performance of the products, its shelf life, and application characteristics
will depend on many variables, including the kind of materials to which
the product will be applied, the environment in which the product is
HEALTH AND SAFETY INFORMATION stored or applied, and the equipment used for application. Any change in
any of these variables can affect the product’s performance. It is the
buyer’s obligation, prior to using the product, to test the suitability of the
For health and safety instruction, first aid product for an intended use. Bostik does not warrant the products
suitability for any application. The product is sold pursuant to Bostik’s
measures and spillage and disposal Terms and Conditions of Sale that accompanies the product at the time
instructions, see separate Safety Data Sheet. of sale.
Nothing contained herein shall be construed to imply the nonexistence of
any relevant patents or to constitute permission, inducement, or
recommendation to practice any invention covered by any patent, without
authority from the owner of the past.
Block B310 WB 3
