MODEL

AX-218 Injection molding machine 218T (servo) 27,100.00

MACHINE MAIN COMPONENTS INFORMATION
Configuration Servo Motor Machine
Computer Controller Techmation
Driver Techmation
Pump Eckerle
Air breaker Schneider
Contactor Schneider
Limit Switches Omrom

ARLEX2022 Linear Transducer Worge

Directional Valve Rexroth
Hydraulic Motor Lei Dun
Airproof Seal Hallite
Lubrication Pump Japan Herg
High-pressure Pipe Aestr
Pressure gauge Taiwan
STANDARD AND OPTIONAL FEATURES

STANDARD OPTIONAL STANDARD OPTIONAL

INJECTION UNIT CLAMPING UNIT
Double balance carriage cylinder Five points double support toggle system
Multi-stage injection speed and pressure seting Triple safety protection:Mechanical,electrical and hydraulic
Multi-stage holding speed and pressure seting Low pressure mold protection device
Multi-stage charging speed and pressure seting Multi-stage pressure, speed and position control
Injection switch to holding control Three options of ejection mode
Injection position detection control Anti-friction rail of moving platen
Injection transducer control Mold cooling water metal manifold
Screw pretection when machine cold boot Mold cooling water manifold with meter and level indicator
Injection purge guard Automatic centralized lubrication system
Three options of the carriage retreat Lubrication system leaking terminal detection
Auto material cleaning Rapid molding differential close/open
High-torque hydraulic motor plasticizing Mold open/close brake function
Electrical motor plasticizing Hydaulic motor mold adjusment
Suck back for prevent the material flowing out Singel core & puller / air blow
Screw rotation speed indicator Multi core & puller / air blow
Bi-metal Screw Clamping open/close transducer
Bi-metal Barrel Ejection forward/backward transducer
Other screw and barrel set Ejection position detection
PID controller barrel temperature Muti ejector for balance ejection
Nano heaters Automatic mold adjustment
Back pressure controled by manual Max. mold adjustment position detection switches
Back pressure controled by proportional valve Adjustable moving platen sild support
Shut-off Nozel T -slot platen with screw
Barrel throat temperature control Heat insulating platen
Nozzle regulation centre adjustement Automatic door
Carriage transducer control Simultaneously action for calmping, ejetion and charging
Maunual lubricants for injection unit By-pass oil fillter
Auto lubricants for injection unit
Electrical & Hydraulic

Energy saving servo system System hardware I/O detection function

Computer data protection locking Output sockets supply for other electrical device

Machine action image display Multiple languages

Molds data storage Emergency stop

Real time monitoring shows of actions Self-lock high precision oil fillter

Faults alarm Oil temperature alarm

Robot interface (Euromap 12\67) Oil temperature cooling condenser

Motor protection function Oil condenser shut off vavle

TECHNICAL SPECIFICATIONS
DESCRIPTION UNIT AX-90 AX-120 AX-140 AX-158
Injection Unit A B C A B C A B C A B C
Screw Diameter mm 32 35 38 35 38 42 38 42 45 42 44 48
Screw L/D Ratio L/D 22 20.1 18. 22 20.2 18.4 23.2 21 19.6 22.5 21 19.7
Shot Volume (Theoretical) ㎤ 135 162 19 165 197 238 226 277 318 277 304 361
Injection Weight(PS) g 123 147 17 150 179 217 206 252 289 252 276 328
Injection Rate g/s 90 108 128 85 101 123 115 138 159 148 165 196
Injection Pressure Mpa 203 170
219 186 152 205 170 147 170 155 130
Screw Speed rpm 0-250 0-215 0-220 0-250
Clamping Unit
Clamp Tonnage KN 900 1200 1400 1580
Toggle Stroke mm 320 350 380 410
Platen Dimention mm 545*510 585*585 635*635 670*665
Space Between Tie Bars mm 360*330 380*380 420*420 455*440
Max. Mold Height mm 350 400 450 470
Min. Mold Height mm 150 155 160 160
Min.Mold Size mm 255*235 260*260 300*300 320*320
Ejector Stroke mm 90 100 120 120
Ejector Tonnage KN 30 38 38 38
Others
Max. Pump Pressure Mpa 16 16 16 16
Motor Power Kw 12 12 18.2 18.2
Heater Power Kw 6.8 7.45 8.9 10
Machine Dimension (L×W×H) m 3.90*1.19*1.80 4.32*1.27*1.90 4.64*1.40*2.00 4.85*1.40*2.10
Machine Weight t 2.8 3.1 3.6 4.4
Oil Tank Capacity L 140 160 170 200
Special Note
Main Power Supply Breaker Model 100 100 100 100
Electric Power Cable Diameter mm² 10 10 10 10
Mould Locating Ring Diameter mm Ø125 Ø125 Ø125 Ø125
Nozzel Hole Diameter mm Ø3 Ø3 Ø3 Ø3
Nozzel Tip Radius SR 10 10 10 10
Platen Mould Clamp Bolt Dia. mm M16 M16 M16 M16
Oil Condenser Pipe Fitting Dia. mm 3/4" 3/4" 3/4" 1"
Cooling Water for Oil Condenser L/min 20 20 30 36
Foundation Carrying For machine Ton/m² 1 1 1.5 1.5

DESCRIPTION UNIT AX-178 AX-218 AX-278 AX-318

Injection Unit A B C A B C A B C A B C
Screw Diameter mm 42 45 50 45 50 55 55 60 65 55 60 65
Screw L/D Ratio L/D 23.6 22 19. 23.3 21 19.1 23 21 19.4 23 21 19.4
Shot Volume (Theoretical) ㎤ 308 353 43 358 441 535 651 775 909 700 834 978
Injection Weight(PS) g 280 321 39 326 406 492 592 705 827 637 759 890
Injection Rate g/s 140 160
170 210 255 220 265 310 220 265 310
Injection Pressure Mpa 203 177
210 168 140 196 164 140 196 164 140
Screw Speed rpm 0-200 0-205 0-195 0-200
Clamping Unit
Clamp Tonnage KN 1780 2180 2780 3180
Toggle Stroke mm 435 475 550 590
Platen Dimention mm 712*712 790*790 845*845 940*940
Space Between Tie Bars mm 470*470 520*520 580*580 630*630
Min.Mold Size mm 325*325 360*360 420*420 440*440
Max. Mold Height mm 520 550 600 630
Min. Mold Height mm 180 200 220 230
Ejector Stroke mm 135 140 140 150
Ejector Tonnage KN 50 70 70 70
Others
Max. Pump Pressure Mpa 16 16 16 16
Motor Power Kw 18.2 23 31 36
Heater Power Kw 10.35 13.6 16.5 16.5
Machine Dimension (L×W×H) m 5.15*1.43*2.15 5.50*1.50*2.20 6.20*1.64*2.25 6.60*1.78*2.30
Machine Weight t 5.2 6.6 7.6 9.6
Oil Tank Capacity L 250 300 350 450
Special Note
Main Power Supply Breaker Model 100 100 160 160
Electric Power Cable Diameter mm² 10~16 10~16 16 16
Mould Locating Ring Diameter mm Ø125 Ø160 Ø160 Ø160
Nozzel Hole Diameter mm Ø3 Ø3 Ø4.5 Ø4.5
Nozzel Tip Radius SR 10 10 15 15
Platen Mould Clamp Bolt Dia. mm M16 M16 M20 M20
Oil Condenser Pipe Fitting Dia. mm 1" 1" 1" 1"
Cooling Water for Oil Condenser L/min 45 58 72 86
Foundation Carrying For machine Ton/m² 2 2 2 2.5

DESCRIPTION UNIT AX-358 AX-408 AX-478 AX-568

Injection Unit A B C A B C A B C A B C
Screw Diameter mm 60 65 70 70 75 80 75 80 85 80 85 90
Screw L/D Ratio L/D 22.8 21 19. 22.5 21 19.7 22.4 21 19.8 22.3 21 19.8
Shot Volume (Theoretical) ㎤ 905 1060 1229 1366 1567 1786 1723 1960 2213 2210 2498 2800
Injection Weight(PS) g 823 964 1118 1243 1426 1625 1568 1784 2014 2011 2273 2548
Injection Rate g/s 250 296 385 440
313 360 411 430 482 546
Injection Pressure Mpa 206 176 186 164
199 173 152 184 163 145
Screw Speed rpm 0-165 0-160 0-160 0-155
Clamping Unit
Clamp Tonnage KN 3580 4080 4780 5680
Toggle Stroke mm 650 720 770 820
Platen Dimention mm 1005*1005 1095*1095 1170*1170 1240*1240
Space Between Tie Bars mm 680*680 730*730 780*780 830*830
Min.Mold Size mm 475*475 510*510 545*545 580*580
Max. Mold Height mm 720 750 800 850
Min. Mold Height mm 250 250 300 350
Ejector Stroke mm 160 180 200 230
Ejector Tonnage KN 90 90 110 150
Others
Max. Pump Pressure Mpa 16 16 16 16
Motor Power Kw 36 40 67 36+36
Heater Power Kw 18.6 26 31 34.5
Machine Dimension (L×W×H) m 7.50*1.92*2.40 8.35*2.00*2.50 9.15*2.13*2.60 9.42*2.20*2.90
Machine Weight t 11.6 15.5 18.4 22
Oil Tank Capacity L 600 685 715 950
Special Note
Main Power Supply Breaker Model 160 160 160 200
Electric Power Cable Diameter mm² 16 25 25~35 25~50
Mould Locating Ring Diameter mm Ø160 Ø160 Ø200 Ø200
Nozzel Hole Diameter mm Ø4.5 Ø4.5 Ø4.5 Ø4.5
Nozzel Tip Radius SR 15 15 15 15
Platen Mould Clamp Bolt Dia. mm M20 M20 M20 M20
Oil Condenser Pipe Fitting Dia. mm 5/4" 5/4" 5/4" 5/4"
Cooling Water for Oil Condenser L/min 100 120 150 165
Foundation Carrying For machine Ton/m² 3 3 3 3.5

DESCRIPTION UNIT AX-658 AX-788 AX-988

Injection Unit A B C D A B C D A B C D
Screw Diameter mm 85 90 95 100 90 95 105 110 90 100 110 120
Screw L/D Ratio L/D 22 21 20 18. 23.2 22 19.8 19 24 22 20 18.3
Shot Volume (Theoretical) ㎤ 553 2862 3189 353 2990 3331 4070 4466 3180 3926 4751 5654
Injection Weight(PS) g 323 2604 2902 321 2721 3032 3073 4064 2894 3573 4324 5145
Injection Rate g/s 470 526 587 558 690 835
574 640 781 859
Injection Pressure Mpa 184 165 149 228 184 152
195 175 143 130
Screw Speed rpm 0-140 0-130 0-110
Clamping Unit
Clamp Tonnage KN 6580 7880 9880
Toggle Stroke mm 900 980 1120
Platen Dimention mm 1310*1310 1465*1465 1575*1575
Space Between Tie Bars mm 880*880 980*980 1080*1080
Min.Mold Size mm 615*615 685*685 755*755
Max. Mold Height mm 900 960 1100
Ejector Stroke mm 250 280 300
Ejector Tonnage KN 150 210 210
Others
Max. Pump Pressure Mpa 16 16 16
Motor Power Kw 36+36 36+40 55+55
Heater Power Kw 42 46 55.5
Machine Dimension (L×W×H) m 9.90*2.25*2.90 10.90*2.40*3.45 11.80*2.50*3.55
Machine Weight t 26 35 46
Oil Tank Capacity L 1000 1150 1250
Special Note
Main Power Supply Breaker Model 250 320 350
Electric Power Cable Diameter mm² 35~50 50 50~70
Mould Locating Ring Diameter mm Ø200 Ø250 Ø250
Nozzel Hole Diameter mm Ø4.5 Ø4.5 Ø6
Nozzel Tip Radius SR 15 20 20
Platen Mould Clamp Bolt Dia. mm M20 M24 M24
Oil Condenser Pipe Fitting Dia. mm 3/4" 5/4" 3/2"
Cooling Water for Oil Condenser L/min 165 180 220
Foundation Carrying For machine Ton/m² 4 4 5
FACTORY 01(HQ & ASSEMBLY) FACTORY 01(PARTS PROCESS) FACTORY 01(PARTS PROCESS)

OFFICE ENVIRONMENT：

WORKSHOP：

REFERANCE MARKEST

U.S.A U.K MEXICO PORTUGAL TURKEY

Please confirm your acceptance of this quote by signing this document

Thank you for your business!
Should you have any enquiries concerning this quote, please contact Simon Min on +86-131-3639-8231
Factory：No. 63, Huangsu East Road, Dongqian Lake Industrial Park, Ningbo,China
Tel:+86-574-8686 3287 Fax:+86-574-8686 3272 E-mail:[email protected]