50 Hz

Z10, Z12
Series
10” - 12” SUBMERSIBLE
ELECTRIC PUMPS

Cod. 191005601 Rev

Rev .B Ed.08/2012
ev.B
Z10, Z12 SERIES
HYDRA ULIC PERFORMANCE RANGE A
HYDRAULIC T 50 Hz
AT
200 300 400 500 600 700 800 900 1000 Q [Imp gpm] 2000

200 300 400 500 600 700 800 900 1000 Q [US gpm] 2000
800

600 2000
500
400

300 1000
800
200
600
500
H [m]

H [ft]
400

Z10150

Z10220

Z10275
Z12340

Z12420
100
300
80

60 200
50
40

30 100
80
20
60
50
40
10
30
8

6 20
5
4

03830_B_CH
3
30 40 50 60 70 80 90 100 Q [m /h] 200 300 400 500 600

500 600 800 1000 Q [l/min] 2000 3000 4000 5000 6000 8000 10000

2
CONTENTS

Z10 Series Specifications ....................................................................................................................... 5

Z10 Table of Materials ........................................................................................................................... 6
Hydraulic Performance Range, Z10 Series 50 Hz .................................................................................... 7
Z12 Series Specifications .................................................................................................................. 31
Z12 Table of Materials ..................................................................................................................... 32
Hydraulic Performance Range, Z12 Series 50 Hz .............................................................................. 33
L6W Series Motors .......................................................................................................................... 49
L8W Series Motors .......................................................................................................................... 57
L10W Series Motors ........................................................................................................................ 65
L12W Series Motors ......................................................................................................................... 71
77
Accessories ......................................................................................................................................

Technical Appendix .......................................................................................................................... 95

3
4
10” MARKET SECTORS
Submersible AGRICULTURAL, INDUSTRIAL, MUNICIPAL.
Electric APPLICATIONS
APPLICATIONS
Pumps • Water supply from deep wells.
• Pressure boosting and water distribution in civil and
industrial systems.
Z10150 • Supply of surge tanks and reservoirs.
Z10220 • Firefighting and washing systems.
Z10275 • Water table level control.
• Irrigation.
Series
SPECIFICATIONS
SPECIFICATIONS • Maximum number of starts per hour:
PUMP 15 (L6W), 10 (L8W) 8 (L10W) 4 (L12W).
• Delivery
Delivery: up to 350 m3/h. • Maximum temperature of water in
• Head
Head: up to 545 m. contact with motor:
• Maximum pump overall diameter L6W, L8W, L10W and L12W 30°C.
(2 cable covers included): 271 mm. • Special versions
versions: AISI 316 and
• Maximum electric pump immersion Duplex materials, HT for applications
depth: 350 m with L6W, L8W, L10W in high temperature environments
and L12W motors. (up to 60°C) or under inverter.
• The content of sand should not exceed
50 g/m3, higher contents up to 100 g/m3 CONSTRUCTION
can be admitted, if wear is tolerated. FEATURES
FEATURES
• Horizontal installation possible (it is PUMP
recommended to have an incline of at • Robust but lightweight, easy to
least 3° with the motor on the lowest maintain and with high corrosion
position). resistance.
• Standard delivery outlet: • Impeller and diffusers made of
Rp 6” according to EN 10226. stainless steel castings.
• Motor power: from 11 to 300 kW. • Delivery head and suction support of
stainless steel castings.
MOTOR • Stainless steel non return valve
• L6W, L8W, L10W and L12W integrated, spring equipped.
rewindable water filled three-phase • Stainless steel shaft.
motors. • Guide bearings and wear rings ensure
• Three-phase version
version: high reliability and long lasting
L6W: 4 to 37 kW 380-415 V, 50 Hz. hydraulic performances.
L8W: 30 to 93 kW 380-415 V, 50 Hz. • The new design ensures high efficiency
L10W: 93 to 150 kW 380-415 V, and low power consumption
50 Hz. • Special versions
versions: ZR10 made of
L12W: 185 to 300 kW 380-415 V, Duplex stainless steel.
50 Hz. • Coupling according to NEMA standard
• Maximum supply voltage variations: for 6” and 8” motor, with key
L6W, L8W, L10W, L12W 400V ±10%. connection for 10” and 12” motor.
• Horizontal operation
operation:
L6W, all versions are designed for ACCESSORIES
ACCES SORIES
horizontal installation, provided that • Coupling flange.
the direction of the axial thrust • Panels.
generated by the impellers is always • Drop cables.
from the pump to the motor. • Cooling shrouds.
L8W, L10W, L12W available on requests • Temperature sensor PT 100 / PTC
PTC.
for all versions.

5
TTABELLA
ABLE OFMATERIALI
MA Z10
TERIALS
MATERIALS Z10
COMPONENT MATERIAL DESIGNATION

EUROPE USA
Delivery head / Valve Casing Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Valve Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Valve seat NBR 90
Valve spring Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
Diffuser / Bowl Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Diffuser O-Ring NBR 70
Impeller Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Taperlock Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Wear ring POM
Lower support / Suction Casing Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Suction strainer Stainless steel DIN 17440-X6CrNiMoTi17-12-2 (1.4571) AISI 316Ti
Pump shaft Stainless steel EN 10088-1-X17CrNi16-2 (1.4057) AISI 431
Coupling Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Bearing bush EPDM + LOXAMID ®
Thrust Bearing PTFE + 25% carbon
Screw, stud, nut Stainless steel ISO 3506-1/2 A4-70 AISI 316
Cable protection Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI 304

TTABELLA MATERIALI ZR10 ZR10 z10-2p50-en_b_tm

ABLE OF MA TERIALS
MATERIALS
COMPONENT MATERIAL DESIGNATION
EUROPE USA
Delivery head / Valve Casing Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Valve Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Valve seat NBR 90
Valve spring Hastelloy C4 DIN17744-NiMo16Cr16Ti (2.4610) N06455
Diffuser / Bowl Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Diffuser O-Ring NBR 70
Impeller Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Taperlock Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Wear ring POM
Lower support / Suction Casing Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Suction strainer Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
Pump shaft Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Coupling Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Bearing bush EPDM + LOXAMID ®
Thrust Bearing PTFE + 25% carbon
Screw, stud, nut Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cable protection Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
zr10-2p50-en_a_tm
IDENTIFICATION CODE
IDENTIFICATION
Z R 10 150 05 / 2 B L8W

MOTOR CODE
REDUCTION TYPE
NUMBER OF REDUCED STAGES
NUMBER OF STAGES
FLOW RATE IN m3/h
TYPE OF PUMP (R = DUPLEX VERSION)
BLANK = 50 Hz
6 = 60 Hz

EXAMPLE : ZR10 150 05/2B - L8W

10” electric pump, 50 Hz, made of DUPLEX, flow rate 150 m3/h, 5 stages including 2 reduced ones, coupled to an 8” L8W motor.

6
Z10 SERIES
HYDRA ULIC PERFORMANCE RANGE A
HYDRAULIC T 50 Hz
AT
Z10 ∼ 2900 [rpm] ISO 9906 - Annex A

200 300 400 500 600 700 800 1000 Q [Imp gpm]

200 300 400 500 600 700 800 1000 Q [US gpm]
800
700
600 2000

500

H [ft]
400

300 1000

800
700
200
600
H [m]

500

400

100
300
Z10150

Z10220

Z10275
80
70
60 200

50

40

30 100

80
70
20
60
50

40

10
30
8
7
6 20

5
03829_B_CH

3
30 40 50 60 70 80 90 100 200 300 Q [m400/h]

500 600 800 1000 2000 3000 4000 Q [l/min]

5000 6000

7
Z10150 SERIES, 1 TO 3 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10150 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 667 1333 2000 2500 3000
TYPE POWER m3/h 0 40 80 120 150 180

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10150 01/1C 11 34 31 29 25 19 12
Z10150 01/1B 13 39 36 34 30 25 18
Z10150 01/1A 15 42 40 38 34 29 22
Z10150 02/2C 22 67 63 58 49 38 23
Z10150 02/2B 26 79 74 70 60 50 36
Z10150 02/2A 30 86 81 77 68 59 45
Z10150 03/2C 37 112 105 98 85 69 48
Z10150 03/2B 45 123 116 109 96 81 61
Z10150 03/2A 45 129 121 115 102 88 68
Z10150 03 52 134 126 121 109 94 74
z10150-2p50-1-en_a_th

DIMENSIONI E PESI SERIE Z10150 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10150 01/1C-L6W 11 1428 258 144 2323 103
Z10150 01/1B-L6W 13 1468 258 144 2363 107
Z10150 01/1A-L6W 15 1538 258 144 2433 115
Z10150 02/2C-L6W 22 1864 258 144 2543 146
Z10150 02/2B-L6W 26 1992 258 144 2671 155
Z10150 02/2A-L6W 30 2072 258 144 2751 163
Z10150 03/2C-L6W 37 2388 258 144 2851 203
Z10150 03/2B-L8W 45 2332 258 192 2795 270
Z10150 03/2A-L8W 45 2332 258 192 2795 270
Z10150 03-L8W 52 2422 258 192 2885 290 D min = 270 mm.

z10150-2p50-1-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L6W motor.
C = 255 mm with L8W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

8
Z10150 SERIES, 1 TO 3 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

Z10150 ∼ 2900 [rpm] ISO 9906 - Annex A

0 200 400 600 800 Q [Imp gpm]

0 200 400 600 800 1000 Q [US gpm]
150
Korrekturfaktor für η
H [m]

H [ft]
Factor de
Facteur decorrection
correctionduduηη
Correcting Factor of η
125 3 Stufen/etages/stages Coeff.
3/2A 400
1/1A,1/1B,1/1C 0,98
3/2B
2/2A,2/2B,2/2C 0,99
3/2C
100
300
2/2A
75 2/2B
2/2C 200
50
1/1A
1/1B
1/1C 100
25

0 0
50
PP [kW]

3 60
3/2A

PP [HP]
40
3/2B
3/2C
30 40
2/2A
2/2B
20
2/2C
1/1A 20
10 1/1B
1/1C

0 0
12 100

30 η
8 80
NPSH [m]

NPSH [ft]

η [%]

20 NPSH
4 60
10

0 40
03820_A_CH

0 50 100 150 200 Q [m³/h] 250

0 1000 2000 3000 Q [l/min] 4000

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

9
Z10150 SERIES, 4 TO 6 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10150 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 667 1333 2000 2500 3000
TYPE POWER m3/h 0 40 80 120 150 180

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10150 04/2C 52 157 147 138 122 101 74
Z10150 04/2B 60 169 158 150 133 113 87
Z10150 04 67 178 168 161 145 126 98
Z10150 05/2C 67 201 189 178 158 132 98
Z10150 05/2B 75 212 199 189 168 144 110
Z10150 05 83 221 209 200 179 156 122
Z10150 06/2C 83 245 231 218 194 163 122
Z10150 06/1B 93 263 248 236 211 183 143
Z10150 06 110 273 158 247 223 194 154

z10150-2p50-2-en_a_th

DIMENSIONI E PESI SERIE Z10150 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10150 04/2C-L8W 52 2638 258 192 2885 311
Z10150 04/2B-L8W 60 2728 258 192 2975 328
Z10150 04-L8W 67 2818 258 192 3065 346
Z10150 05/2C-L8W 67 3034 258 192 3065 367
Z10150 05/2B-L8W 75 3124 258 192 3155 384
Z10150 05-L8W 83 3184 258 192 3215 397
Z10150 06/2C-L8W 83 3400 258 192 3215 417
Z10150 06/1B-L8W 93 3540 258 192 3355 442
Z10150 06-L10W 110 3524 259 236 3302 558
D min = 270 mm.

z10150-2p50-2-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L8W motor.
C = 255 mm with L10W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

10
Z10150 SERIES, 4 TO 6 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

11
Z10150 SERIES, 7 TO 12 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10150 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 667 1333 2000 2500 3000
TYPE POWER m3/h 0 40 80 120 150 180

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10150 07/3B 110 301 284 270 240 207 159
Z10150 07/1B 110 312 294 280 252 219 172
Z10150 08/3B 130 349 329 313 279 241 189
Z10150 08 130 362 342 327 295 257 203
Z10150 09/3B 150 395 372 354 316 274 213
Z10150 09 150 410 387 371 335 292 231
Z10150 10 185 455 430 412 372 324 257
Z10150 11 185 499 472 452 407 355 281
Z10150 12 220 546 517 494 446 389 308

z10150-2p50-3-en_a_th

DIMENSIONI E PESI SERIE Z10150 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10150 07/3B-L10W 110 3740 259 236 3302 579
Z10150 07/1B-L10W 110 3740 259 236 3302 579
Z10150 08/3B-L10W 130 4106 259 236 3452 647
Z10150 08-L10W 130 4106 259 236 3452 647
Z10150 09/3B-L10W 150 4452 259 236 3582 706
Z10150 09-L10W 150 4452 259 236 3582 706
Z10150 10-L12W 185 4425 283 276 3339 793
Z10150 11-L12W 185 4641 283 276 3339 814
Z10150 12-L12W 220 5007 283 276 3489 898
D min = 270 mm (with 10” motors)
D min = 300 mm (with 12” motors)

z10150-2p50-3-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L10W motor.
C = 280 mm with L12W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

12
Z10150 SERIES, 7 TO 12 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A
ATT 50 Hz

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

13
Z10220 SERIES, 1 TO 3 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10220 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1000 2000 3000 4000 5000
TYPE POWER m3/h 0 60 120 180 240 300

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10220 01/1C 15 32,5 30,4 27,2 22,3 14,5 1,0
Z10220 01/1B 18,5 37,2 34,9 32,1 27,9 20,3 8,3
Z10220 01/1A 22 41,3 38,7 35,9 32,4 25,0 13,6
Z10220 01 26 44,7 41,6 38,8 35,6 28,7 18,3
Z10220 02/2C 30 65,5 61,2 54,9 45,8 29,5 2,0
Z10220 02/2B 37 75,4 70,8 65,1 56,9 41,7 16,8
Z10220 02/2A 45 83,9 78,4 72,9 65,8 51,1 28,6
Z10220 02 52 89,4 83,2 77,6 71,2 57,5 36,8
Z10220 03/2B 60 119,9 112,3 103,8 92,2 70,5 35,3
Z10220 03/2A 67 128,5 120,1 111,6 101,2 79,8 46,8
Z10220 03 75 134,1 124,8 116,3 106,7 86,3 55,1

z10220-2p50-1-en_a_th

DIMENSIONI E PESI SERIE Z10220 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10220 01/1C-L6W 15 1538 258 144 3733 114
Z10220 01/1B-L6W 18,5 1608 258 144 3803 122
Z10220 01/1A-L6W 22 1648 258 144 3843 125
Z10220 01-L6W 26 1776 258 144 3971 134
Z10220 02/2C-L6W 30 2072 258 144 4051 161
Z10220 02/2B-L6W 37 2172 258 144 4151 180
Z10220 02/2A-L8W 45 2116 258 192 4095 247
Z10220 02-L8W 52 2206 258 192 4185 267
Z10220 03/2B-L8W 60 2512 258 192 4275 304
Z10220 03/2A-L8W 67 2602 258 192 4365 322 D min = 270 mm.
Z10220 03-L8W 75 2692 258 192 4455 339

z10220-2p50-1-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L6W motor.
C = 255 mm with L8W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

14
Z10220 SERIES, 1 TO 3 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT
Z10220 ∼ 2900 [rpm] ISO 9906 - Annex A

0 250 500 750 1000 Q [Imp gpm] 1250

0 250 500 750 1000 1250 Q [US1500

gpm]

Korrekturfaktor für η
3 Facteur de correction du η
125 3/2A Correcting Factor of η 400
3/2B Stufen/etages/stages Coeff.
1,1/1A,1/1B,1/1C 0,98
2,2/2A,2/2B,2/2C 0,99
100
H [m]

300
2
2/2A

H [ft]
75 2/2B
2/2C
200
50
1
1/1A
1/1B
1/1C 100
25

0 0
80
100
3
3/2A
60 80
PP [kW]

3/2B
PP [HP]
2 60
40 2/2A
2/2B 2/2C
40
1
20 1/1A
1/1B 20
1/1C
0 0
15 100
40 η
NPSH [m]

10 80
NPSH [ft]

30
η [%]

NPSH
20
5 60
10

0 40
03839_B_CH

0 50 100 150 200 250 300 Q [m³/h] 350

0 1000 2000 3000 4000 5000 Q [l/min]

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

15
Z10220 SERIES, 4 TO 7 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10220 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1000 2000 3000 4000 5000
TYPE POWER m3/h 0 60 120 180 240 300

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10220 04/2B 83 165 155 143 128 99 54
Z10220 04/2A 93 173 162 150 137 109 66
Z10220 04 110 182 170 159 146 119 79
Z10220 05/2B 110 215 201 186 168 133 79
Z10220 05 130 231 213 199 182 148 99
Z10220 06/2B 150 262 245 228 206 165 100
Z10220 06 150 274 255 238 219 178 118
Z10220 07/2B 185 305 297 278 256 208 118
Z10220 07 185 320 297 278 256 208 138

z10220-2p50-2-en_a_th

DIMENSIONI E PESI SERIE Z10200 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10220 04/2B-L8W 83 2968 258 192 4515 371
Z10220 04/2A-L8W 93 3108 258 192 4655 396
Z10220 04-L10W 110 3092 259 236 4602 512
Z10220 05/2B-L10W 110 3308 259 236 4602 531
Z10220 05-L10W 130 3458 259 236 4752 578
Z10220 06/2B-L10W 150 3804 259 236 4882 636
Z10220 06-L10W 150 3804 259 236 4882 636
Z10220 07/2B-L12W 185 3777 283 276 4639 722
Z10220 07-L12W 185 3777 283 276 4639 722
D min = 270 mm (with 8” motors)
D min = 270 mm (with 10” motors)
D min = 300 mm (with 12” motors)

z10220-2p50-2-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L8W motor.
C = 255 mm with L10W motor and C = 280 mm with L12W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

16
Z10220 SERIES, 4 TO 7 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT
Z10220 ∼ 2900 [rpm] ISO 9906 - Annex A

0 250 500 750 1000 Q [Imp gpm] 1250

0 250 500 750 1000 1250 Q [US1500

gpm]

7 1000
300 7/2B
900
6
250 6/2B
800

H [ft]
H [m]

5
700
5/2B
200
600
4
4/2A
4/2B 500
150

400

100
300

200
50

7
7/2B
150
PP [kW]

6 200
6/2B PP [HP]
5
150
5/2B
100
4
4/2A
4/2B 100

50
15 100
40 η
NPSH [m]

10 80
NPSH [ft]

30
η [%]

NPSH
20
5 60
10

0 40
03840_B_CH

0 50 100 150 200 250 300 Q [m³/h] 350

0 1000 2000 3000 4000 5000 Q [l/min]

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

17
Z10220 SERIES, 8 TO 12 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10220 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1000 2000 3000 4000 5000
TYPE POWER m3/h 0 60 120 180 240 300

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10220 08/2B 185 351 328 305 277 223 138
Z10220 08 220 367 343 321 294 241 160
Z10220 09/2B 220 399 373 347 316 255 160
Z10220 09/1A 220 410 383 357 328 267 173
Z10220 10/2B 260 446 416 387 353 285 179
Z10220 10 260 460 428 400 368 300 200
Z10220 11/2B 260 488 456 423 386 312 196
Z10220 11 300 505 471 440 405 330 220
Z10220 12/2B 300 536 500 465 425 344 218
Z10220 12 300 549 512 478 440 358 235

z10220-2p50-3-en_a_th

DIMENSIONI E PESI SERIE Z10200 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10220 08/2B-L12W 185 3993 283 276 4639 741
Z10220 08-L12W 220 4143 283 276 4789 805
Z10220 09/2B-L12W 220 4359 283 276 4789 824
Z10220 09/1A-L12W 220 4359 283 276 4789 824
Z10220 10/2B-L12W 260 4725 283 276 4939 907
Z10220 10-L12W 260 4725 283 276 4939 907
Z10220 11/2B-L12W 260 4941 283 276 4939 927
Z10220 11-L12W 300 5091 283 276 5089 992
Z10220 12/2B-L12W 300 5307 283 276 5089 1011
Z10220 12-L12W 300 5307 283 276 5089 1011 D min = 300 mm

z10220-2p50-3-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 280 mm with L12W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,3 Kg.

18
Z10220 SERIES, 8 TO 12 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A
ATT 50 Hz
Z10220 ∼ 2900 [rpm] ISO 9906 - Annex A

0 250 500 750 1000 Q [Imp gpm] 1250

0 250 500 750 1000 1250 Q [US1500

gpm]

1800
12
12/2B
500
11 1600
11/2B
H [m]

10
10/2B 1400

H [ft]
400 9/1A
9/2B
1200
8
8/2B

300 1000

800

200
600

400
300 400
12
12/2B
11 350
250 11/2B
PP [HP]
10
PP [kW]

10/2B 300
9/1A
200 9/2B
8 250
8/2B
150 200

150
100
15 100
40 η
NPSH [m]

10 80
NPSH [ft]

30
η [%]

NPSH
20
5 60
10

0 40
03841_B_CH

0 50 100 150 200 250 300 Q [m³/h] 350

0 1000 2000 3000 4000 5000 Q [l/min]

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

19
Z10275 SERIES, 1 TO 3 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10275 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1333 2500 3667 4667 5833
TYPE POWER m3/h 0 80 150 220 280 350

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10275 01/1B 18,5 33 29,7 26,6 22,6 16,5
Z10275 01/1A 22 37,5 34,1 31 27,5 22,2 12,3
Z10275 01 30 41,6 38,6 35,9 32,6 28,5 18,6
Z10275 02/2B 37 67 60,3 54 46,1 34
Z10275 02/2A 45 75,7 69,2 62,9 56 45,4 26
Z10275 02 55 82,6 76,7 71 64,6 56,4 36,5
Z10275 03/2B 60 107,8 98,3 89,2 78 61,8
Z10275 03/3A 67 113,6 103,8 94,3 84,1 68,2 39
Z10275 03/1A 75 120,5 111,3 102,6 92,5 79 50
Z10275 03 83 123,9 115,1 106,8 97 84,6 54,8
z10275-2p50-1-en_a_th

DIMENSIONI E PESI SERIE Z10275 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10275 01/1B-L6W 18,5 1608 258 144 3803 122
Z10275 01/1A-L6W 22 1648 258 144 3843 125
Z10275 01-L6W 30 1856 258 144 4051 142
Z10275 02/2B-L6W 37 2172 258 144 4151 180
Z10275 02/2A-L8W 45 2116 258 192 4095 248
Z10275 02-L8W 55 2246 258 192 4225 274
Z10275 03/2B-L8W 60 2512 258 192 4275 304
Z10275 03/3A-L8W 67 2602 258 192 4365 322
Z10275 03/1A-L8W 75 2692 258 192 4455 339
Z10275 03-L8W 83 2752 258 192 4515 352 D min = 270 mm.

z10275-2p50-1-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L6W motor.
C = 255 mm with L8W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,8 Kg.

20
Z10275 SERIES, 1 TO 3 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

21
Z10275 SERIES, 4 TO 7 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10275 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1333 2500 3667 4667 5833
TYPE POWER m3/h 0 80 150 220 280 350

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10275 04/3A 93,0 154 142 130 116 96 58
Z10275 04/2A 110 162 150 138 124 105 67
Z10275 04 110 169 157 146 132 116 77
Z10275 05/3A 130 202 186 171 154 130 82
Z10275 05 150 212 197 183 167 146 98
Z10275 06/3A 150 242 224 206 186 157 100
Z10275 06 185 253 235 218 199 174 116
Z10275 07/2A 185 288 267 246 223 192 124
Z10275 07 185 297 276 257 233 205 138

z10275-2p50-2-en_a_th

DIMENSIONI E PESI SERIE Z10275 2 poli 50 Hz

DIMENSIONS AND WEIGHT

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10275 04/3A-L8W 93 3108 258 192 4655 397
Z10275 04/2A-L10W 110 3092 259 236 4602 513
Z10275 04-L10W 110 3092 259 236 4602 513
Z10275 05/3A-L10W 130 3458 259 236 4752 579
Z10275 05-L10W 150 3588 259 236 4882 618
Z10275 06/3A-L10W 150 3804 259 236 4882 638
Z10275 06-L12W 185 3561 283 276 4639 703
Z10275 07/2A-L12W 185 3777 283 276 4639 723
Z10275 07-L12W 185 3777 283 276 4639 723
D min = 270 mm (with 8” motors)
D min = 270 mm (with 10” motors)
D min = 300 mm (with 12” motors)

z10275-2p50-2-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 255 mm with L8W motor.
C = 255 mm with L10W motor and C = 280 mm with L12W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,8 Kg.

22
Z10275 SERIES, 4 TO 7 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

23
Z10275 SERIES, 8 TO 11 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z10275 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 1333 2500 3667 4667 5833
TYPE POWER m3/h 0 80 150 220 280 350

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z10275 08/2B 220 324 299 276 248 217 143
Z10275 08/1A 220 336 312 289 263 229 152
Z10275 09/3A 260 372 344 317 287 247 160
Z10275 09 260 382 355 330 300 264 177
Z10275 10/3A 260 413 382 352 319 275 179
Z10275 10 300 426 396 368 335 294 199
Z10275 11/1A 300 464 430 399 363 316 211

z10275-2p50-3-en_a_th

DIMENSIONI E PESI SERIE Z10275 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z10275 08/2B-L12W 220 4143 283 276 4789 806
Z10275 08/1A-L12W 220 4143 283 276 4789 806
Z10275 09/3A-L12W 260 4509 283 276 4939 890
Z10275 09-L12W 260 4509 283 276 4939 890
Z10275 10/3A-L12W 260 4725 283 276 4939 909
Z10275 10-L12W 300 4875 283 276 5089 974
Z10275 11/1A-L12W 300 5091 283 276 5089 994

D min = 300 mm

z10275-2p50-3-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 280 mm with L12W motor.
2) T min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 146 mm, and reduce weight by 8,8 Kg.

24
Z10275 SERIES, 8 TO 11 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A
ATT 50 Hz

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

25
Z10150 PUMP SERIES
DIMENSIONI E PESI SERIE Z10150 A 50 Hz
DIMENSIONS AND WEIGHTS
MAX Ø
PUMP POWER DIMENSIONS (mm) MIN.
WEIGHT
TYPE ABSORBED WELL
BY PUMP
kW (4) (1) (2) (3) mm
L C U kg
Z10150 01/1C 10,3 442 258 1600 48,1 270
Z10150 01/1B 12,8 442 258 1600 48,1 270
Z10150 01/1A 14,8 442 258 1600 48,1 270
Z10150 02/2C 20,5 658 258 1600 68,8 270
Z10150 02/2B 25,7 658 258 1600 68,8 270
Z10150 02/2A 29,6 658 258 1600 68,8 270
Z10150 03/2C 36,2 874 258 1600 89,5 270
Z10150 03/2B 41,3 874 258 1600 89,8 270
Z10150 03/2A 44,4 874 258 1600 89,8 270
Z10150 03 46,9 874 258 1600 89,8 270
Z10150 04/2C 51,8 1090 258 1600 110,5 270
Z10150 04/2B 57,0 1090 258 1600 110,5 270
Z10150 04 62,6 1090 258 1600 110,5 270
Z10150 05/2C 67,4 1306 258 1600 131,2 270
Z10150 05/2B 72,6 1306 258 1600 131,2 270
Z10150 05 78,2 1306 258 1600 131,2 270
Z10150 06/2C 83,0 1522 258 1600 151,9 270
Z10150 06/1B 91,0 1522 258 1600 151,9 270
Z10150 06 93,8 1522 258 1600 156,8 270
Z10150 07/3B 101,1 1738 258 1600 177,5 270
Z10150 07/1B 106,7 1738 258 1600 177,5 270
Z10150 08/3B 116,7 1954 258 1600 198,2 270
Z10150 08 125,1 1954 258 1600 198,2 270
Z10150 09/3B 132,4 2170 258 1600 218,9 270
Z10150 09 140,8 2170 258 1600 218,9 270
Z10150 10 156,4 2386 271 1600 240,4 300
Z10150 11 172,0 2602 271 1600 261,1 300
Z10150 12 187,7 2818 271 1600 281,8 300
DIMENSIONI ACCOPPIAMENTO MOTORI SERIE Z10 50 Hz
MOTOR COUPLING z10150p-50-en_a_td

MOTOR
DIMENSIONS (mm)
CONNECTION

N k d z b E H7 R l
6" (NEMA) 182 111,2 13,5 4 17 76,2 73 263
8" (NEMA) 182 152,4 18 4 17 127 101,45 263
10" 232 190,5 22 4 15 127 101,45 300
12" 232 190,5 22 4 15 127 126,85 300
DIMENSIONS (mm)
COUPLING Profile of gear coupling according to NEMA
NUMBER DIAMETRAL PRESSURE
OF TEETH PITCH ANGLE X
6" (NEMA) 15 16/32 30° 20
8" (NEMA) 23 16/32 30° 38
DIMENSIONS (mm)
COUPLING +0.084 +0.1 +0.05
F +0.059 H P +0.02 X
10" 42,85 47,6 9,5 84
12" 49.212 54,5 12,7 95
z10-mtcn-50-en_b_td

1) Max pump diameter with 2 motor cables included.

2) U min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
3) Weight with non-return valve. For pumps without non-return valve, reduce by 8,3 Kg.
4) For pumps without non-return valve, reduce dimension L by 146 mm.

26
Z10220 PUMP SERIES
DIMENSIONI E PESI SERIE Z10200 A 50 Hz
DIMENSIONS AND WEIGHTS
MAX Ø
PUMP POWER DIMENSIONS (mm) MIN.
WEIGHT
TYPE ABSORBED WELL
BY PUMP
kW (4) (1) (2) (3) mm
L C U kg
Z10220 01/1C 14,6 442 258 2900 47,3 270
Z10220 01/1B 18,0 442 258 2900 47,3 270
Z10220 01/1A 21,5 442 258 2900 47,3 270
Z10220 01 24,0 442 258 2900 47,3 270
Z10220 02/2C 29,2 658 258 2900 66,6 270
Z10220 02/2B 36,0 658 258 2900 66,6 270
Z10220 02/2A 43,0 658 258 2900 66,9 270
Z10220 02 48,0 658 258 2900 66,9 270
Z10220 03/2B 60,0 874 258 2900 86,2 270
Z10220 03/2A 67,0 874 258 2900 86,2 270
Z10220 03 72,0 874 258 2900 86,2 270
Z10220 04/2B 84,0 1090 258 2900 105,5 270
Z10220 04/2A 91,0 1090 258 2900 105,5 270
Z10220 04 96,0 1090 258 2900 110,4 270
Z10220 05/2B 108,0 1306 258 2900 129,7 270
Z10220 05 120,0 1306 258 2900 129,7 270
Z10220 06/2B 132,0 1522 258 2900 149 270
Z10220 06 144,0 1522 258 2900 149 270
Z10220 07/2B 156,0 1738 271 2900 169,1 300
Z10220 07 168,0 1738 271 2900 169,1 300
Z10220 08/2B 180,0 1954 271 2900 188,4 300
Z10220 08 192,0 1954 271 2900 188,4 300
Z10220 09/2B 204,0 2170 271 2900 207,7 300
Z10220 09/1A 213,5 2170 271 2900 207,7 300
Z10220 10/2B 228,0 2386 271 2900 227 300
Z10220 10 240,0 2386 271 2900 227 300
Z10220 11/2B 252,0 2602 271 2900 246,3 300
Z10220 11 264,0 2602 271 2900 246,3 300
Z10220 12/2B 276,0 2818 271 2900 265,6 300
Z10220 12 288,0 2818 271 2900 265,6 300

DIMENSIONI ACCOPPIAMENTO MOTORI SERIE Z10 50 Hz

MOTOR COUPLING z10220p-50-en_a_td

MOTOR
DIMENSIONS (mm)
CONNECTION

N k d z b E H7 R l
6" (NEMA) 182 111,2 13,5 4 17 76,2 73 263
8" (NEMA) 182 152,4 18 4 17 127 101,45 263
10" 232 190,5 22 4 15 127 101,45 300
12" 232 190,5 22 4 15 127 126,85 300
DIMENSIONS (mm)
COUPLING Profile of gear coupling according to NEMA
NUMBER DIAMETRAL PRESSURE
OF TEETH PITCH ANGLE X
6" (NEMA) 15 16/32 30° 20
8" (NEMA) 23 16/32 30° 38
DIMENSIONS (mm)
COUPLING +0.084 +0.1 +0.05
F +0.059 H P +0.02 X
10" 42,85 47,6 9,5 84
12" 49.212 54,5 12,7 95
z10-mtcn-50-en_b_td

1) Max pump diameter with 2 motor cables included.

2) U min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
3) Weight with non-return valve. For pumps without non-return valve, reduce by 8,3 Kg.
4) For pumps without non-return valve, reduce dimension L by 146 mm.

27
Z10275 PUMP SERIES
DIMENSIONI E PESI SERIE Z10275 A 50 Hz
DIMENSIONS AND WEIGHTS
MAX Ø
PUMP POWER DIMENSIONS (mm) MIN.
WEIGHT
TYPE ABSORBED WELL
BY PUMP
kW (4) (1) (2) (3) mm
L C U kg
Z10275 01/1B 17,3 442 258 2900 47,4 270
Z10275 01/1A 21,9 442 258 2900 47,4 270
Z10275 01 26,9 442 258 2900 47,4 270
Z10275 02/2B 34,6 658 258 2900 66,9 270
Z10275 02/2A 43,8 658 258 2900 67,2 270
Z10275 02 53,8 658 258 2900 67,2 270
Z10275 03/2B 61,5 874 258 2900 86,7 270
Z10275 03/3A 65,7 874 258 2900 86,7 270
Z10275 03/1A 75,7 874 258 2900 86,7 270
Z10275 03 80,7 874 258 2900 86,7 270
Z10275 04/3A 92,6 1090 258 2900 106,2 270
Z10275 04/2A 97,6 1090 258 2900 111,1 270
Z10275 04 107,6 1090 258 2900 111,1 270
Z10275 05/3A 119,5 1306 258 2900 130,6 270
Z10275 05 134,5 1306 258 2900 130,6 270
Z10275 06/3A 146,4 1522 258 2900 150,1 270
Z10275 06 161,4 1522 271 2900 150,1 300
Z10275 07/2A 178,3 1738 271 2900 170,4 300
Z10275 07 188,3 1738 271 2900 170,4 300
Z10275 08/2B 196,0 1954 271 2900 189,9 300
Z10275 08/1A 210,2 1954 271 2900 189,9 300
Z10275 09/3A 227,1 2170 271 2900 209,4 300
Z10275 09 242,1 2170 271 2900 209,4 300
Z10275 10/3A 254,0 2386 271 2900 228,9 300
Z10275 10 269,0 2386 271 2900 228,9 300
Z10275 11/1A 290,9 2602 271 2900 248,4 300
DIMENSIONI ACCOPPIAMENTO MOTORI SERIE Z10 z10275p-50-en_a_td
50 Hz
MOTOR COUPLING
MOTOR
DIMENSIONS (mm)
CONNECTION

N k d z b E H7 R l
6" (NEMA) 182 111,2 13,5 4 17 76,2 73 263
8" (NEMA) 182 152,4 18 4 17 127 101,45 263
10" 232 190,5 22 4 15 127 101,45 300
12" 232 190,5 22 4 15 127 126,85 300
DIMENSIONS (mm)
COUPLING Profile of gear coupling according to NEMA
NUMBER DIAMETRAL PRESSURE
OF TEETH PITCH ANGLE X
6" (NEMA) 15 16/32 30° 20
8" (NEMA) 23 16/32 30° 38
DIMENSIONS (mm)
COUPLING +0.084 +0.1 +0.05
F +0.059 H P +0.02 X
10" 42,85 47,6 9,5 84
12" 49.212 54,5 12,7 95
z10-mtcn-50-en_b_td

1) Max pump diameter with 2 motor cables included.

2) U min valid only for max flow speed of 4,5 m/s between pump and perforation pipe.
3) Weight with non-return valve. For pumps without non-return valve, reduce by 8,8 Kg.
4) For pumps without non-return valve, reduce dimension L by 146 mm.

28
Z10 SERIES
PUMP CROS
CROSSS SECTION AND LIST OF COMPONENTS

DENOMINAZIONE COMPONENTI
SERIE Z10-2poli 50 Hz

REF. N. DESCRIPTION

1 Stage casing
2 Suction casing
3 Delivery casing
4 Valve body
5 Bearing bush
6 Impeller
7 Wear ring
8 Shaft
9 Coupling
10 Locking sleeve
11 Thrust bearing
12 Valve plate
13 Valve seat
14 Valve spring
15 Wing valve
16 Suction strainer
17 Cable
18 Cable protection
19 O-ring
20 Intermediate ring
z10-2p50-en_a_tp

29
30
12” MARKET SECTORS
Submersible AGRICULTURAL, INDUSTRIAL, MUNICIPAL.
Electric APPLICATIONS
APPLICATIONS
Pumps • Water supply from deep wells.
• Pressure boosting and water distribution in civil and
industrial systems.
Z12340 • Supply of surge tanks and reservoirs.
Z12420 • Firefighting and washing systems.
Series • Water table level control.
• Irrigation.

SPECIFICATIONS
SPECIFICATIONS • Maximum number of starts per hour:
PUMP 10 (L8W) 8 (L10W) 4 (L12W).
• Delivery
Delivery: up to 520 m3/h. • Maximum temperature of water in
• Head
Head: up to 450 m. contact with motor:
• Maximum pump overall diameter L8W, L10W and L12W 30°C.
(2 cable covers included): 302 mm. • Special versions
versions: AISI 316 and
• Maximum electric pump immersion Duplex materials, HT for applications
depth: 350 m with L8W, L10W in high temperature environments
and L12W motors. (up to 60°C) or under inverter.
• The content of sand should not exceed
50 g/m3, higher contents up to 100 g/m3 CONSTRUCTION
can be admitted, if wear is tolerated. FEATURES
FEATURES
• Horizontal installation possible (it is PUMP
recommended to have an incline of at • Robust but lightweight, easy to
least 3° with the motor on the lowest maintain and with high corrosion
position). resistance.
• Standard delivery outlet: • Impeller and diffusers made of
8” NPT according to API. stainless steel castings.
• Motor power: from 30 to 350 kW. • Delivery head and suction support of
• Electric pumps with powers up to stainless steel castings.
300 kW are supplied with Lowara • Stainless steel non return valve
motor series. For larger powers please integrated, spring equipped.
contact our sales network. • Stainless steel shaft.
• Guide bearings and wear rings ensure
MOTOR high reliability and long lasting
• L8W, L10W and L12W rewindable hydraulic performances.
water filled three-phase motors. • The new design ensures high efficiency
• Three-phase version
version: and low power consumption.
L8W: 30 to 93 kW 380-415 V, 50 Hz. • Special versions
versions: ZR12 made of
L10W: 93 to 150 kW 380-415 V, Duplex stainless steel.
50 Hz. • Coupling according to NEMA standard
L12W: 185 to 300 kW 380-415 V, for 8” motor, with key connection for
50 Hz. 10” and 12” motor.
• Maximum supply voltage variations:
L8W, L10W, L12W 400V ±10%. ACCES SORIES
ACCESSORIES
• Horizontal operation
operation: • Coupling flange.
L8W, L10W and L12W all versions are • Panels.
designed for horizontal installation, • Drop cables.
provided that the direction of the axial • Cooling shrouds.
thrust generated by the impellers is • Temperature sensor PT 100 / PTC
PTC.
always from the pump to the motor.

31
TTABELLA
ABLE OFMATERIALI
MA Z12
TERIALS
MATERIALS Z12
COMPONENT MATERIAL DESIGNATION

EUROPE USA
Delivery head / Valve Casing Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Valve Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Valve seat NBR 90
Valve spring Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
Diffuser / Bowl Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Diffuser O-Ring NBR 70
Impeller Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Taperlock Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Wear ring POM
Lower support / Suction Casing Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) A744-CF 8
Suction strainer Stainless steel DIN 17440-X6CrNiMoTi17-12-2 (1.4571) AISI 316Ti
Pump shaft Stainless steel EN 10088-1-X17CrNi16-2 (1.4057) AISI 431
Coupling Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Bearing bush EPDM + LOXAMID ®
Thrust Bearing PTFE + 25% carbon
Screw, stud, nut Stainless steel ISO 3506-1/2 A4-70 AISI 316
Cable protection Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI 304

TTABELLA MATERIALI ZR12 ZR12 z12-2p50-en_b_tm

ABLE OF MA TERIALS
MATERIALS
COMPONENT MATERIAL DESIGNATION
EUROPE USA
Delivery head / Valve Casing Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Valve Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Valve seat NBR 90
Valve spring Hastelloy C4 DIN17744-NiMo16Cr16Ti (2.4610) N06455
Diffuser / Bowl Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Diffuser O-Ring NBR 70
Impeller Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Taperlock Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Wear ring POM
Lower support / Suction Casing Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
Suction strainer Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
Pump shaft Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Coupling Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Bearing bush EPDM + LOXAMID ®
Thrust Bearing PTFE + 25% carbon
Screw, stud, nut Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cable protection Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
zr12-2p50-en_a_tm
IDENTIFICATION CODE
IDENTIFICATION
Z R 12 340 02 / 2 B L8W

MOTOR CODE
REDUCTION TYPE
NUMBER OF REDUCED STAGES
NUMBER OF STAGES
FLOW RATE IN m3/h
TYPE OF PUMP (R = DUPLEX VERSION)
BLANK = 50 Hz
6 = 60 Hz

EXAMPLE : ZR12 340 02/2B - L8W

12” electric pump, 50 Hz, made of DUPLEX, flow rate 340 m3/h, 2 stages including 2 reduced ones, coupled to an 8” L8W motor.

32
Z12 SERIES
HYDRA ULIC PERFORMANCE RANGE A
HYDRAULIC T 50 Hz
AT

33
Z12340 SERIES, 1 TO 2 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12340 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2000 3333 4667 5667 6667
TYPE POWER m3/h 0 120 200 280 340 400

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12340 01/1B 30 45,5 41,1 35,5 30,1 24,5 15,2
Z12340 01/1A 37 50,0 44,8 39,6 34,8 29,7 21,1
Z12340 01 45 55,4 49,8 44,7 40,0 36,2 28,9
Z12340 02/2C 52 82,7 75,6 63,8 52,2 39,2 20,0
Z12340 02/2B 60 90,3 81,5 70,5 60,1 48,4 29,1
Z12340 02/2A 75 100,6 90,3 79,8 70,1 60,1 43,0
Z12340 02 93 110,7 99,6 89,3 79,9 72,5 57,8

z12340-2p50-1-en_a_th

DIMENSIONI E PESI SERIE Z12340 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12340 01/1B-L8W 30 1765 290 192 3915 217
Z12340 01/1A-L8W 37 1855 290 192 4005 234
Z12340 01-L8W 45 1945 290 192 4095 252
Z12340 02/2C-L8W 52 2270 290 192 4185 300
Z12340 02/2B-L8W 60 2360 290 192 4275 317
Z12340 02/2A-L8W 75 2540 290 192 4455 352
Z12340 02-L8W 93 2740 290 192 4655 390

D min = 305 mm.

z12340-2p50-1-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 285 mm with L8W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

34
Z12340 SERIES, 1 TO 2 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

35
Z12340 SERIES, 3 TO 4 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12340 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2000 3333 4667 5667 6667
TYPE POWER m3/h 0 120 200 280 340 400

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12340 03/2C 110 137 124 107 91 74 49
Z12340 03/3A 110 153 137 122 107 92 67
Z12340 03/1A 130 163 147 131 117 104 81
Z12340 03 150 169 153 137 122 112 90
Z12340 04/2B 150 204 185 163 143 125 92
Z12340 04/2A 185 214 194 172 153 135 104
Z12340 04 185 225 202 182 162 148 119

z12340-2p50-2-en_a_th

DIMENSIONI E PESI SERIE Z12340 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12340 03/2C-L10W 110 2982 302 236 4602 531
Z12340 03/3A-L10W 110 2982 302 236 4602 531
Z12340 03/1A-L10W 130 3132 302 236 4752 578
Z12340 03-L10W 150 3262 302 236 4882 617
Z12340 04/2B-L10W 150 3497 302 236 4882 644
Z12340 04/2A-L12W 185 3254 306 276 4639 710
Z12340 04-L12W 185 3254 306 276 4639 710

D min = 315 mm (with 10” motors)

D min = 320 mm (with 12” motors)

z12340-2p50-2-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 293 mm with L10W motor.
C = 300 mm with L12W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

36
Z12340 SERIES, 3 TO 4 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

37
Z12340 SERIES, 5 TO 8 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12340 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2000 3333 4667 5667 6667
TYPE POWER m3/h 0 120 200 280 340 400

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12340 05/2B 220 262 237 210 185 163 124
Z12340 05/2A 220 272 245 219 195 174 135
Z12340 05 220 283 255 229 205 187 152
Z12340 06/2B 260 319 288 256 226 201 155
Z12340 06/2A 260 329 297 265 236 211 165
Z12340 06 260 339 306 274 246 224 182
Z12340 07/3A 300 379 341 304 271 241 187
Z12340 07 300 396 357 320 286 262 212
Z12340 08/3A 350 437 393 351 313 279 218
Z12340 08 350 452 408 366 327 299 242
z12340-2p50-3-en_a_th

DIMENSIONI E PESI SERIE Z12340 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12340 05/2B-L12W 220 3639 306 276 4789 801
Z12340 05/2A-L12W 220 3639 306 276 4789 801
Z12340 05-L12W 220 3639 306 276 4789 801
Z12340 06/2B-L12W 260 4024 306 276 4939 893
Z12340 06/2A-L12W 260 4024 306 276 4939 893
Z12340 06-L12W 260 4024 306 276 4939 893
Z12340 07/3A-L12W 300 4409 306 276 5089 985
Z12340 07-L12W 300 4409 306 276 5089 985
Z12340 08/3A-** 350 - - - - -
Z12340 08-** 350 - - - - -

D min = 320 mm.

** For power above 350 kW please contact our sales network. z12340-2p50-3-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 300 mm with L12W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

38
Z12340 SERIES, 5 TO 8 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

39
Z12420 SERIES, 1 TO 2 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12420 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2500 4167 5833 7000 8667
TYPE POWER m3/h 0 150 250 350 420 520

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12420 01/1C 30 38,8 36,1 31 25 18
Z12420 01/1B 37 44,1 40,1 35,1 29,6 25 12
Z12420 01/1A 45 49,3 45,0 39,6 34,4 30,5 18,8
Z12420 01 52 52,2 47,7 42,3 37,0 33,9 22,3
Z12420 02/2C 60 77,1 71,7 61,0 48,9 36,0
Z12420 02/2B 75 88,7 80,8 70,8 59,7 49,7 24,0
Z12420 02/2A 93 99,3 90,7 79,9 69,3 61,6 39
Z12420 02 110 106,5 97,6 86,6 75,9 69,9 47,3

z12420-2p50-1-en_a_th

DIMENSIONI E PESI SERIE Z10200 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12420 01/1C-L8W 30 1765 290 192 3915 217
Z12420 01/1B-L8W 37,0 1855 290 192 4005 234
Z12420 01/1A-L8W 45 1945 290 192 4095 252
Z12420 01-L8W 52 2035 290 192 4185 272
Z12420 02/2C-L8W 60 2360 290 192 4275 317
Z12420 02/2B-L8W 75 2540 290 192 4455 352
Z12420 02/2A-L8W 93 2740 290 192 4655 390
Z12420 02-L10W 110 2747 302 236 4602 504

D min = 305 mm (with 8” motors)

D min = 315 mm (with 10” motors)

z10200-2p50-1-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 285 mm with L8W motor.
C = 293 mm with L10W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

40
Z12420 SERIES, 1 TO 2 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

41
Z12420 SERIES, 3 TO 4 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12420 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2500 4167 5833 7000 8667
TYPE POWER m3/h 0 150 250 350 420 520

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12420 03/2C 110 132 122 106 89 72 36
Z12420 03/2B 130 143 132 115 99 85 50
Z12420 03/3A 150 151 138 122 106 94 60
Z12420 03 150 160 146 130 114 104 71
Z12420 04/3B 185 188 173 151 129 111 64
Z12420 04/3A 185 204 187 165 144 129 84
Z12420 04 220 215 197 175 154 131 97

z12420-2p50-2-en_a_th

DIMENSIONI E PESI SERIE Z12420 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12420 03/2C-L10W 110 2982 302 236 4602 531
Z12420 03/2B-L10W 130 3132 302 236 4752 577
Z12420 03/3A-L10W 150 3262 302 236 4882 617
Z12420 03-L10W 150 3262 302 236 4882 617
Z12420 04/3B-L12W 185 3254 306 276 4639 710
Z12420 04/3A-L12W 185 3254 306 276 4639 710
Z12420 04-L12W 220 3404 306 276 4789 774

D min = 315 mm (with 10” motors)

D min = 320 mm (with 12” motors)

z12420-2p50-2-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 293 mm with L10W motor.
C = 300 mm with L12W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

42
Z12420 SERIES, 3 TO 4 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT
Z12420 ∼ 2900 [rpm] ISO 9906 - Annex A

0 250 500 750 1000 1250 1500 1750 2000 Q [Imp gpm]

0 250 500 750 1000 1250 1500 1750 2000 2250 2500 Q [US gpm]
225
4 700
4/3A
200
H [m]

4/3B
600
175

H [ft]
3
150 3/3A 500
3/2B
3/2C
125 400

100
300

75
200
50

100
25

200 4
4/3A 240
175
PP [kW]

4/3B PP [HP]
150 200
3
3/3A
125
3/2B 160

100 3/2C
120

24 100
η
60
NPSH [m]

16 80
NPSH [ft]

η [%]

40
NPSH
8 60
20

0 40
03835_A_CH

0 100 200 300 400 500 Q [m³/h] 600

0 2000 4000 6000 8000 Q [l/min] 10000

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

43
Z12420 SERIES, 5 TO 7 ST AGES
STAGES
TABELLA DI PRESTAZIONI IDRAULICHE SERIE Z12420 2 poli 50 Hz
OPERA
OPERATINGTING CHARACTERISTIC
CHARACTERISTICS S AATT 50 Hz
Q = DELIVERY
PUMP RATED l/min 0 2500 4167 5833 7000 8667
TYPE POWER m3/h 0 150 250 350 420 520

kW H = TOTAL HEAD METRES COLUMN OF WATER

Z12420 05/2B 260 251 231 203 177 156 102
Z12420 05 260 268 246 218 191 174 121
Z12420 06/2B 300 305 280 247 215 191 128
Z12420 06 300 321 294 261 229 208 143
Z12420 07/2B 350 359 329 291 254 226 152
Z12420 07 350 375 344 306 268 244 169

z12420-2p50-3-en_a_th

DIMENSIONI E PESI SERIE Z12420 2 poli 50 Hz

DIMENSIONS AND WEIGHTS

PUMP RATED
DIMENSIONS (mm) WEIGHT
TYPE POWER

kW A (4) C (1) M T (2) kg (3)

Z12420 05/2B-L12W 260 3789 306 276 4939 865
Z12420 05-L12W 260 3789 306 276 4939 865
Z12420 06/2B-L12W 300 4174 306 276 5089 958
Z12420 06-L12W 300 4174 306 276 5089 958
Z12420 07/2B-** 350 - - - - -
Z12420 07-** 350 - - - - -

D min = 320 mm

** For power above 350 kW please contact our sales network. z12420-2p50-3-en_a_td

1) Max electric pump diameter with 2 motor cables included.

In case of 1 motor cable C = 300 mm with L12W motor.
2) T min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
In case this velocity is exceeded, please contact our sales network.
3) Without cables.
4) For pumps without non-return valve, reduce dimension A by 188 mm, and reduce weight by 16,7 Kg.

44
Z12420 SERIES, 5 TO 7 STAGES
STAGES
OPERATING CHARACTERISTIC
OPERATING CHARACTERISTICSS A T 50 Hz
AT

These performances are valid for liquids with density ρ = 1.0 Kg/dm3 and kinematic viscosity ν = 1 mm2/sec.

45
Z12340 PUMP SERIES
DIMENSIONI E PESI SERIE Z12340 A 50 Hz
DIMENSIONS AND WEIGHTS
MAX Ø
PUMP POWER DIMENSIONS (mm) MIN.
WEIGHT
TYPE ABSORBED WELL
BY PUMP
kW (4) (1) (2) (3) mm
L C U kg
Z12340 01/1B 29,2 510 290 2900 72 305
Z12340 01/1A 34,9 510 290 2900 72 305
Z12340 01 42,6 510 290 2900 72 305
Z12340 02/2C 50,5 745 290 2900 99,3 305
Z12340 02/2B 57,2 745 290 2900 99,3 305
Z12340 02/2A 70,5 745 290 2900 99,3 305
Z12340 02 84,2 745 290 2900 99,3 305
Z12340 03/2C 94,6 980 302 2900 129,4 315
Z12340 03/3A 109,1 980 302 2900 129,4 315
Z12340 03/1A 124,5 980 302 2900 129,4 315
Z12340 03 132,4 980 302 2900 129,4 315
Z12340 04/2B 147,4 1215 302 2900 156,7 315
Z12340 04/2A 159,6 1215 302 2900 157,5 320
Z12340 04 173,8 1215 302 2900 157,5 320
Z12340 05/2B 193,3 1450 302 2900 184,8 320
Z12340 05/2A 205,2 1450 302 2900 184,8 320
Z12340 05 219,5 1450 302 2900 184,8 320
Z12340 06/2B 235,2 1685 302 2900 212,1 320
Z12340 06/2A 246,5 1685 302 2900 212,1 320
Z12340 06 260,7 1685 302 2900 212,1 320
Z12340 07/3A 280,0 1920 302 2900 239,4 320
Z12340 07 301,0 1920 302 2900 239,4 320
Z12340 08/3A 333,1 2155 302 2900 266,7 320
Z12340 08 354,8 2155 302 2900 266,7 320
DIMENSIONI ACCOPPIAMENTO MOTORI SERIE Z12 50 Hz
MOTOR COUPLING
z12340p-50-en_a_td

MOTOR
DIMENSIONS (mm))
CONNECTION

N k d z b E H7 R l
8" (NEMA) 185 152,4 M16 4 20 127 101,45 240
10" 232 190,5 M20 4 22 127 101,45 300
12" 232 190,5 M20 4 23 127 126,85 300

DIMENSIONS (mm)
COUPLING Profile of gear coupling according to NEMA
NUMBER DIAMETRAL PRESSURE
OF TEETH PITCH ANGLE X
8" (NEMA) 23 16/32 30° 38
DIMENSIONS (mm)
COUPLING
F H P X
h6
10" 42.85 47,6 9,5 86
12" 49.212h6 54,5 12,7 95
z12-mtcn-50-en_a_td

1) Max pump diameter with 2 motor cables included.

2) U min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
3) Weight with non-return valve. For pumps without non-return valve, reduce by 16,7 Kg.
4) For pumps without non-return valve, reduce dimension L by 188 mm.

46
Z12420 PUMP SERIES
DIMENSIONI E PESI SERIE Z12420 A 50 Hz
DIMENSIONS AND WEIGHTS
MAX Ø
PUMP POWER DIMENSIONS (mm) MIN.
WEIGHT
TYPE ABSORBED WELL
BY PUMP
kW (4) (1) (2) (3) mm
L C U kg
Z12420 01/1C 29,7 510 290 2900 72 305
Z12420 01/1B 35,4 510 290 2900 72 305
Z12420 01/1A 43,1 510 290 2900 72 305
Z12420 01 47,0 510 290 2900 72 305
Z12420 02/2C 58,2 745 290 2900 99,3 305
Z12420 02/2B 71,5 745 290 2900 99,3 305
Z12420 02/2A 86,2 745 290 2900 99,3 305
Z12420 02 98,5 745 302 2900 102,1 315
Z12420 03/2C 109,6 980 302 2900 129,4 315
Z12420 03/2B 122,8 980 302 2900 129,4 315
Z12420 03/3A 134,1 980 302 2900 129,4 315
Z12420 03 147,8 980 302 2900 129,4 315
Z12420 04/3B 161,3 1215 302 2900 157,5 320
Z12420 04/3A 184,3 1215 302 2900 157,5 320
Z12420 04 200,1 1215 302 2900 157,5 320
Z12420 05/2B 223,1 1450 302 2900 184,8 320
Z12420 05 247,6 1450 302 2900 184,8 320
Z12420 06/2B 269,8 1685 302 2900 212,1 320
Z12420 06 291,0 1685 302 2900 212,1 320
Z12420 07/2B 325,4 1920 302 2900 239,4 320
Z12420 07 350,2 1920 302 2900 239,4 320
z12420p-50-en_a_td

DIMENSIONI ACCOPPIAMENTO MOTORI SERIE Z12 50 Hz

MOTOR COUPLING
MOTOR
DIMENSIONS (mm))
CONNECTION

N k d z b E H7 R l
8" (NEMA) 185 152,4 M16 4 20 127 101,45 240
10" 232 190,5 M20 4 22 127 101,45 300
12" 232 190,5 M20 4 23 127 126,85 300

DIMENSIONS (mm)
COUPLING Profile of gear coupling according to NEMA
NUMBER DIAMETRAL PRESSURE
OF TEETH PITCH ANGLE X
8" (NEMA) 23 16/32 30° 38
DIMENSIONS (mm)
COUPLING
F H P X
h6
10" 42.85 47,6 9,5 86
12" 49.212h6 54,5 12,7 95
z12-mtcn-50-en_a_td

1) Max pump diameter with 2 motor cables included.

2) U min valid only for max flow speed of 6,8 m/s between pump and perforation pipe.
3) Weight with non-return valve. For pumps without non-return valve, reduce by 16,7 Kg.
4) For pumps without non-return valve, reduce dimension L by 188 mm.

47
Z12 SERIES
PUMP CROS
CROSSS SECTION AND LIST OF COMPONENTS

DENOMINAZIONE COMPONENTI
SERIE Z12-2poli 50 Hz

REF. N. DESCRIPTION

1 Stage casing
2 Suction casing
3 Delivery casing
4 Valve body
5 Bearing bush
6 Impeller
7 Wear ring
8 Shaft
9 Coupling
10 Locking sleeve
11 Thrust bearing
12 Valve plate
13 Valve seat
14 Valve spring
15 Wing valve
16 Suction strainer
17 Cable
18 Cable protection
19 O-ring
20 Intermediate ring
z12-2p50-en_a_tp

48
6” Water filled submersible motors.
Submersible The robust design together with excellent choise of materials
ensures optimal performance, ease of installation and reliability
motors
in all applications. For extremely demanding operation as high
water temperature or aggressive environments special versions
are available.
L6W
Series
SPECIFICATIONS
SPECIFICATIONS SPECIAL VERSIONS
• Stainless steel outer sleeve. • Motors with double cable outlet for
• Shaft extension and coupling star/delta start.
dimensions to NEMA standards. • L6WN series
series: complete range
• Rewindable stator stator. available realized of AISI 316
• Class Y insulation
insulation. stainless steel.
• Protection class: IP68
IP68. • L6WR series
series: complete range
• Compensating bellows for internal available realized of Duplex
liquid expansion. stainless steel.
• Axial load supported by Kingsbury • HT series
series: complete range
type thrust bearing. available for all the L6W/N/R
• Mechanical seal construction, realized for applications
protected by sand guard. in high temperature environments
• Maximum immersion depth depth: up to 60°C
(up 60°C) or under inverter.
350 m.
• Maximum number of starts per OPTIONAL FEATURES
FEATURES
hour at regular intervals: 15. • Silicon Carbide mechanical seal.
• Maximum supply voltage • Special voltages.
variations allowed : ±10%.
• Maximum water temperature
temperature: ACCES SORIES
ACCESSORIES
30°C. • Temperature sensor PT 100 / PTC
PTC.
Max. temperature applies to motors
working in a installation capable of
delivering a flow of water around the
motor jacket as following:
Standard versions 0,2 m/s (4÷9,3 kW),
0,3 m/s (11÷30 kW) and
0,5 m/s (37 kW).
HT versions 0,2 m/s (5,5÷7,5 kW),
0,3 m/s (9,3÷26 kW) and
0,5 m/s (30 kW).
• Axial thrust
thrust:
16000 N from 4 to 22 kW;
30000 N from 26 to 37 kW.
• Power supply cable suitable
for drinkable water.
‰ Rewindable
• Versions
ersions:
stator - Three-phase:
4 to 37 kW 380-415 V, 50 Hz.
‰ Thrust bearing • Horizontal operation
operation:
valid for all versions provided that the
Kingsbury direction of the axial thrust generated
type by the impellers is always from the
pump to the motor.
• Flat power supply cable.
‰ Mechanical • Screws included.
seal

49
L6W - L6WN - L6WR MOTOR SERIES
MOTOR CROS S SECTION
CROSS

50
MOTORI SERIE L6W: TABELLA MATERIALI
L6W TABLE OF MA
TABLE TERIALS
MATERIALS
REF. PART MATERIAL DESIGNATION
N° EUROPE USA
1
Upper bracket Cast iron EN-GJL-200 Class 25 B
2
Spacer Cast iron EN-GJL-200 Class 25 B
3
Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4
Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5
Cable EPR
Cable gland plate
6 Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
Cable gland
7 EPDM
8
Shaft end Stainless steel EN 10088-1-X20Cr13 (1.4021) AISI420
9
Removable sand guard EPDM
10
Mechanical seal cover Stainless steel EN 10213-4-GX5CrNi19-10 (1.4308) ASTM CF-8 (AISI 304 cast)
11
Mechanical seal Carbon graphite / Aluminium oxide
12
Bush bearings Carbon graphite
13
Elastomers NBR
14
Motor sleeve Stainless steel EN 10088-1-X2CrNi19-11 (1.4306) AISI304L
15
Lower bracket Cast iron EN-GJL-200 Class 25 B
Thrust bearing bracket
16 Cast iron EN-GJL-200 Class 25 B
17
Diaphragm EPDM
18
Lower cover Cast iron EN-GJL-200 Class 25 B
19
Bolts and screws Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
MOTORI SERIE L6WN:
Cooling liquid TABELLA MATERIALI
Water + antifreeze
L6WN TABLE OF MA
TABLE TERIALS
MATERIALS L6w-2p50-en_b_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1Upper bracket Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
2Spacer Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
3Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5Cable EPR
6Cable gland plate Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
7Cable seal EPDM
8Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9Removable sand guard EPDM
10Mechanical seal cover Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
11Mechanical seal Carbon graphite / Aluminium oxide
12Bush bearings Carbon graphite
13Elastomers NBR
14Motor sleeve Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
15Lower bracket Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
16Thrust bearing bracket Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
17Diaphragm EPDM
18Lower cover Stainless steel EN 10213-4-GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
19Bolts and screws Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
MOTORI SERIE L6WR:
Cooling liquid TABELLA MATERIALI
Water + antifreeze
L6WR TABLE OF MA
TABLE TERIALS
MATERIALS L6wn-2p50-en_b_tm

REF. PART MATERIALE DESIGNATION

N° EUROPE USA
1 Upper bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
2 Spacer Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
3 Filling plug + OR Duplex s. s.+NBR EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
4 Vent valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
5 Cable EPR
6 Cable gland plate Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
7 Cable gland EPDM
8 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Removable sand guard EPDM
10 Mechanical seal cover Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
11 Mechanical seal Carbon graphite / Aluminium oxide
12 Bush bearings Carbon graphite
13 Elastomers NBR
14 Motor sleeve Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
15 Lower bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
16 Thrust bearing bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
17 Diaphragm EPDM
18 Lower cover Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
19 Bolts and screws Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cooling liquid Water + antifreeze
L6wr-2p50-en_b_tm

51
L6W MOTOR SERIES
IDENTIFICATION CODE
IDENTIFICATION
L6W 110 T 40 5 /_ HT
HIGH TEMPERATURE

VERSION
5 = 50 Hz
6 = 60 Hz

RATED VOLTAGE
T = THREE-PHASE
RATED POWER IN kW x 10
L6W (CAST IRON STANDARD VERSION)
L6WN (AISI 316 VERSION)
L6WR (DUPLEX VERSION)

EXAMPLE : L6W110T405/A HT

L6W MOTOR :
RATED POWER 11 kW; THREE-PHASE;
RATED VOLTAGE 400 V; 50 Hz; /A VERSION; HIGH TEMPERATURE

RATING PLA
RATING TE
PLATE

LEGEND
1 - Motor type 7 - Weight
2 - Code 8 - Maximum immersion depht
3 - Maximum water temperature 9 - Operating characteristics
4 - Minimum water velocity 10 - Production date
5 - Insulation class 11 - Serial number
6 - Protection class 12 - Characteristics at service factor

52
L6W MOTOR SERIES
DIMENSIONS AND WEIGHTS AT 50 Hz
AT

DIMENSIONI E PESI MOTORI L6W - 2 poli 50 Hz

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L6W40T405 4 5,5 583 38
L6W55T405 5,5 7,5 613 42
L6W75T405 7,5 10 653 46
L6W93T405 9,3 12,5 683 50
L6W110T405 11 15 723 54
L6W130T405 13 17,5 763 58
L6W150T405 15 20 833 66
L6W185T405 18,5 25 903 74
L6W220T405 22 30 943 77
L6W260T405 26 35 1071 86
L6W300T405 30 40 1151 94
L6W370T405 37 50 1301 108
DIMENSIONI E PESI MOTORI L6W HT - 2 poli 50 Hz
l6w-2p50-en_b_td

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L6W40T405 HT 4 5,5 613 42
L6W55T405 HT 5,5 7,5 653 46
L6W75T405 HT 7,5 10 683 50
L6W93T405 HT 9,3 12,5 723 54
L6W110T405 HT 11 15 763 58
L6W130T405 HT 13 17,5 833 66
L6W150T405 HT 15 20 903 74
L6W185T405 HT 18,5 25 943 77
L6W220T405 HT 22 30 1071 86
L6W260T405 HT 26 35 1151 94
L6W300T405 HT 30 40 1301 108
l6w-ht-2p50-en_a_td

53
L6W MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICSS AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
THREE-PHASE CURRENT Sec. (mm2)
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 9,89 2835 68,1 0,9 1,00 3,56
L6W40T405 4 5,5 400 9,26 2865 71,0 0,88 1,13 4,00 30 4 - 4
415 9,13 2880 71,5 0,85 1,21 4,20
380 12,7 2855 75,4 0,88 1,18 4,37
L6W55T405 5,5 7,5 400 12,4 2875 75,7 0,85 1,31 4,70 30 4 4 4
415 12,5 2885 75,4 0,82 1,42 4,85
380 17,0 2840 74,9 0,9 1,26 4,34
L6W75T405 7,5 10 400 16,4 2860 76,0 0,87 1,41 4,74 30 4 4 4
415 16,2 2875 76,5 0,84 1,52 4,96
380 20,5 2840 77,6 0,89 1,51 4,64
L6W93T405 9,3 12,5 400 20,0 2860 78,2 0,86 1,68 5,01 30 4 4 4
415 19,9 2870 78,3 0,83 1,81 5,21
380 24,2 2830 77,2 0,9 1,44 4,38
L6W110T405 11 15 400 23,5 2850 78,0 0,87 1,47 4,75 30 4 4 4
415 23,4 2865 78,0 0,84 1,73 4,94
380 28,1 2830 77,9 0,9 1,31 4,53
L6W130T405 13 17,5 400 27,1 2855 78,9 0,88 1,47 4,93 30 4 4 4
415 27,0 2865 79,1 0,9 1,59 5,15
380 32,1 2830 80,2 0,88 1,55 4,88
L6W150T405 15 20 400 31,5 2855 80,6 0,85 1,72 5,25 30 4 4 4
415 31,3 2865 80,9 0,82 1,86 5,46
380 38,5 2845 81,8 0,89 1,77 5,23
L6W185T405 18,5 25 400 37,6 2860 82,4 0,86 1,97 5,65 30 6 4 4
415 37,5 2870 82,4 0,83 2,13 5,86
380 47,3 2865 81,7 0,87 0,86 4,60
L6W220T405 22 30 400 46,5 2880 82,2 0,83 0,96 4,93 30 6 4 4
415 46,7 2890 82,2 0,8 1,04 5,09
380 56,5 2860 81,9 0,85 1,58 4,82
L6W260T405 26 35 400 55,4 2880 82,7 0,82 1,76 5,18 30 6 4 4
415 55,7 2890 82,7 0,79 1,90 5,35
380 63,8 2870 82,3 0,87 1,07 4,94
L6W300T405 30 40 400 62,3 2890 83,1 0,84 1,19 5,32 30 10 4 4
415 62,0 2900 83,3 0,81 1,29 5,55
380 81,8 2845 79,6 0,86 1,03 4,25
L6W370T405 37 50 400 79,1 2870 81,2 0,83 1,15 4,63 30 10 4 4
415 79,4 2880 80,8 0,80 1,25 4,79
* Ts/Tn = ratio between starting torque and nominal torque. l6w-2p50-en_f_te

54
L6W HT MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICSS AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
THREE-PHASE CURRENT Sec. (mm2)
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 9,81 2905 76,9 0,81 1,65 5,65
L6W40T405 HT 4 5,5 400 10,1 2915 75,5 0,76 1,83 5,78 45 4 4 4
415 10,5 2920 74,2 0,72 1,98 5,77
380 12,9 2895 77,1 0,84 1,75 5,71
L6W55T405 HT 5,5 7,5 400 13,0 2905 77,0 0,79 1..95 5,96 45 4 4 4
415 13,4 2915 76,3 0,75 2,10 6,03
380 16,9 2880 79,2 0,85 1,89 5,64
L6W75T405 HT 7,5 10 400 16,9 2890 79,0 0,81 2,11 5,91 45 4 4 4
415 17,3 2900 78,3 0,77 2,27 6,00
380 20,6 2865 79,2 0,87 1,72 5,13
L6W93T405 HT 9,3 12,5 400 20,4 2880 79,3 0,83 1,82 5,44 45 4 4 4
415 20,8 2890 78,4 0,79 2,07 5,53
380 23,8 2870 80,1 0,88 1,57 5,35
L6W110T405 HT 11 15 400 23,6 2885 80,1 0,84 1,75 5,69 45 4 4 4
415 23,9 2890 79,8 0,80 1,89 5,83
380 28,3 2860 81,8 0,85 1,80 5,55
L6W130T405 HT 13 17,5 400 28,1 2875 81,4 0,82 2,01 5,87 45 4 4 4
415 28,4 2885 81,4 0,78 2,17 6,03
380 31,8 2880 83,6 0,86 2,21 6,33
L6W150T405 HT 15 20 400 31,9 2890 83,4 0,82 2,46 6,65 45 6 4 4
415 32,5 2900 82,8 0,78 2,65 6,77
380 40,3 2895 83,9 0,83 1,04 5,40
L6W185T405 HT 18,5 25 400 40,5 2905 83,5 0,79 1,15 5,65 45 6 4 4
415 41,6 2910 83,0 0,75 1,24 5,71
380 48,5 2890 83,6 0,82 1,89 5,62
L6W220T405 HT 22 30 400 48,6 2905 83,6 0,78 2,10 5,90 45 6 4 4
415 49,7 2910 83,2 0,74 2,26 5,99
380 55,7 2895 83,8 0,85 1,24 5,66
L6W260T405 HT 26 35 400 55,2 2905 84,0 0,81 1,38 6,00 45 10 4 4
415 55,8 2915 83,9 0,77 1,49 6,17
380 67,1 2885 82,2 0,83 1,29 5,18
L6W300T405 HT 30 40 400 67,1 2900 82,8 0,78 1,44 5,46 45 10 4 4
415 68,8 2910 81,8 0,74 1,55 5,52
* Ts/Tn = ratio between starting torque and nominal torque. l6w-ht-2p50-en_c_te

55
56
8” Water filled submersible motors.
Submersible The robust design together with excellent choise of materials
ensures optimal performance, ease of installation and reliability
motors
in all applications. For extremely demanding operation as high
water temperature or aggressive environments special versions
are available.
L8W
Series
SPECIFICATIONS
SPECIFICATIONS SPECIAL VERSIONS
• Stainless steel outer sleeve. • Motors with double cable outlet for
• Shaft extension and coupling star/delta start.
dimensions to NEMA standards. • L8WN series
series: complete range
• Rewindable stator stator. available realized of AISI 316
• Class Y insulation
insulation. stainless steel.
• Protection class: IP68
IP68. • L8WR series
series: complete range
• Compensating bellows for internal available realized of Duplex
liquid expansion. stainless steel.
• Axial load supported by Kingsbury • HT series
series: complete range
type thrust bearing. available for all the L8W/N/R
• Mechanical seal construction, realized for applications
protected by sand guard. in high temperature environments
• Maximum immersion depth depth: up to 60°C
(up 60°C) or under inverter.
350 m.
• Maximum number of starts per OPTIONAL FEATURES
FEATURES
hour at regular intervals: 10. • Silicon Carbide mechanical seal.
• Maximum supply voltage • Special voltages.
variations allowed : ±10%.
• Maximum water temperature
temperature: ACCES SORIES
ACCESSORIES
30°C. • Temperature sensor PT 100 / PTC
PTC.
Max. temperature applies to motors
working in a installation capable of
delivering a flow of water around the
motor jacket of at least 0,5 m/s.
• Axial thrust
thrust:
50000 N from 30 to 93 kW.
• Power supply cable suitable
for drinkable water.
• Versions
ersions:
- Three-phase:
30 to 93 kW 380-415 V, 50 Hz.
• Horizontal operation
operation:
valid for all versions provided that the
direction of the axial thrust generated
by the impellers is always from the
‰ Rewindable
pump to the motor.
stator

‰ Thrust bearing
Kingsbury
type

‰ Mechanical
seal

57
L8W - L8WN - L8WR MOTOR SERIES
MOTOR CROS S SECTION
CROSS

58
L8W MOTOR SERIES: TABLE OF MATERIALS
L8W T ABLE OF MA
TABLE TERIALS
MATERIALS
REF. PART MATERIAL DESIGNATION
N° EUROPE USA
1Upper bracket Cast iron EN-GJL-200 Class 25 B
2Spacer Cast iron EN-GJL-200 Class 25 B
3Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5Cable EPR
6Cable gland plate Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
7Cable gland EPDM
8Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
11Mechanical seal Carbon graphite / Aluminium oxide
12Bush bearings Carbon graphite
13Elastomers NBR
14Motor sleeve Stainless steel EN 10088-1-X2CrNi19-11 (1.4306) AISI304L
15Lower bracket Cast iron EN-GJL-200 Class 25 B
16Thrust bearing bracket Cast iron EN-GJL-200 Class 25 B
17Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18Diaphragm EPDM
19Lower cover Cast iron EN-GJL-200 Class 25 B
20Bolts and screws Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
L8WN
CoolingMOTOR
liquid SERIES:
WaterTABLE OF MATERIALS
+ antifreeze
L8WN TABLE OF MA
TABLE TERIALS
MATERIALS L8w-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1Upper bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
2Spacer Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
3Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5Cable EPR
6Cable gland plate Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
7Cable gland EPDM
8Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
11Mechanical seal Carbon graphite / Aluminium oxide
12Bush bearings Carbon graphite
13Elastomers NBR
14Motor sleeve Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
15Lower bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
16Thrust bearing bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
17Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18Diaphragm EPDM
19Lower cover Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
20Bolts and screws Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
L8WR MOTOR
Cooling liquid SERIES:
WaterTABLE OF MATERIALS
+ antifreeze
L8WR TABLE OF MA
TABLE TERIALS
MATERIALS L8wn-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1 Upper bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
2 Spacer Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
3 Filling plug + OR Duplex s. s.+NBR EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
4 Vent valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
5 Cable EPR
6 Cable gland plate Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
7 Cable gland EPDM
8 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Removable sand guard Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
10 Mechanical seal cover Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
11 Mechanical seal Carbon graphite / Aluminium oxide
12 Bush bearings Carbon graphite
13 Elastomers NBR
14 Motor sleeve Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
15 Lower bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
16 Thrust bearing bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
17 Filling valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
18 Diaphragm EPDM
19 Lower cover Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
20 Bolts and screws Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cooling liquid Water + antifreeze
L8wr-2p50-en_a_tm

59
L8W MOTOR SERIES
IDENTIFICATION CODE
IDENTIFICATION
L8W 550 T 40 5 /_ HT
HIGH TEMPERATURE

VERSION
5 = 50 Hz
6 = 60 Hz

RATED VOLTAGE
T = THREE-PHASE
RATED POWER IN kW x 10
L8W (CAST IRON STANDARD VERSION)
L8WN (AISI 316 VERSION)
L8WR (DUPLEX VERSION)

EXAMPLE : L8W550T405/A HT

L8W MOTOR :
RATED POWER 55 kW; THREE-PHASE;
RATED VOLTAGE 400 V; 50 Hz; /A VERSION; HIGH TEMPERATURE

RATING PLA
RATING TE
PLATE

LEGEND
1 - Motor type 7 - Weight
2 - Code 8 - Maximum immersion depht
3 - Maximum water temperature 9 - Operating characteristics
4 - Minimum water velocity 10 - Production date
5 - Insulation class 11 - Serial number
6 - Protection class 12 - Characteristics at service factor

60
L8W MOTOR SERIES
DIMENSIONS AND WEIGHTS AT 50 Hz
AT

DIMENSIONI E PESI MOTORI L8W - 2 poli 50 Hz

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L8W300T405 30 40 1015 145
L8W370T405 37 50 1105 162
L8W450T405 45 60 1195 180
L8W520T405 52 70 1285 200
L8W550T405 55 75 1325 206
L8W600T405 60 80 1375 217
L8W670T405 67 90 1465 235
L8W750T405 75 100 1555 252
L8W830T405 83 110 1615 265
L8W930T405 93 125 1755 290
DIMENSIONI E PESI MOTORI L8W - 2 poli 50 Hz
l8w-2p50-en_a_td

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L8W300T405 HT 30 40 1105 162
L8W370T405 HT 37 50 1195 180
L8W450T405 HT 45 60 1285 200
L8W520T405 HT 52 70 1325 206
L8W550T405 HT 55 75 1375 217
L8W600T405 HT 60 80 1465 235
L8W670T405 HT 67 90 1555 252
L8W750T405 HT 75 100 1615 265
L8W830T405 HT 83 110 1755 290
l8w-ht-2p50-en_a_td

61
L8W MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICSS AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 65,0 2905 83,0 0,85 1,20 4,67
L8W300T405 30 40 400 62,0 2900 83,0 0,84 1,15 4,69 30 10 6 5,5
415 59,0 2900 83,0 0,84 1,09 4,70
380 81,0 2840 80,5 0,87 1,04 4,19
L8W370T405 37 50 400 78,5 2860 81,0 0,84 1,14 4,54 30 10 6 5,5
415 76,0 2870 81,5 0,83 1,23 4,88
380 92,0 2850 82,0 0,87 0,92 3,72
L8W450T405 45 60 400 89,0 2870 82,0 0,85 1,01 3,98 30 16 6 5,5
415 89,0 2880 83,5 0,83 1,09 4,23
380 110 2840 82,0 0,86 1,14 3,90
L8W520T405 52 70 400 108 2865 82,0 0,85 1,15 4,20 30 16 6 5,5
415 104 2885 82,5 0,82 1,16 4,50
380 118 2840 82,0 0,87 1,26 3,57
L8W550T405 55 75 400 114 2870 82,0 0,85 1,27 3,88 30 16 10 5,5
415 110 2885 82,5 0,83 1,27 4,19
380 124 2855 82,0 0,87 1,12 4,18
L8W600T405 60 80 400 120 2875 82,5 0,85 1,23 4,49 30 16 10 5,5
415 118 2885 83,5 0,83 1,33 4,80
380 138 2850 82,5 0,88 0,98 4,22
L8W670T405 67 90 400 133 2870 83,0 0,86 1,07 4,52 30 25 10 5,5
415 132 2885 83,5 0,83 1,16 4,82
380 156 2860 82,0 0,87 0,92 4,10
L8W750T405 75 100 400 152 2875 82,5 0,85 1,01 4,41 30 25 16 5,5
415 148 2885 83,0 0,82 1,10 4,72
380 172 2860 83,0 0,87 0,91 4,12
L8W830T405 83 110 400 168 2870 83,5 0,84 1,00 4,39 30 35 16 5,5
415 163 2880 84,0 0,82 1,08 4,66
380 192 2850 83,0 0,87 0,84 3,38
L8W930T405 93 125 400 186 2860 83,5 0,85 0,92 3,84 30 35 16 5,5
415 180 2885 84,0 0,83 1,00 4,30
* Ts/Tn = ratio between starting torque and nominal torque. l8w-2p50-en_d_te

62
L8W HT MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO L8W HT A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICS S AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 66,6 2865 82,5 0,84 1,29 5,10
L8W300T405 HT 30 40 400 64,5 2885 83,0 0,81 1,41 5,52 45 10 6 5,5
415 62,4 2895 83,5 0,8 1,53 5,94
380 77,5 2865 84,0 0,86 1,12 4,41
L8W370T405 HT 37 50 400 75,0 2885 84,0 0,84 1,23 4,72 45 16 6 5,5
415 75,0 2895 85,5 0,82 1,33 5,02
380 97,8 2860 83,0 0,83 1,33 4,39
L8W450T405 HT 45 60 400 96,0 2885 83,0 0,82 1,34 4,73 45 16 6 5,5
415 92,4 2905 83,5 0,79 1,35 5,06
380 110 2835 83,0 0,86 1,33 3,84
L8W520T405 HT 52 70 400 106 2865 83,0 0,84 1,34 4,17 45 16 10 5,5
415 102 2880 83,5 0,82 1,34 4,51
380 117 2865 83,5 0,86 1,23 4,44
L8W550T405 HT 55 75 400 113 2885 84,0 0,84 1,34 4,77 45 16 10 5,5
415 111 2895 85,0 0,82 1,46 5,10
380 127 2860 83,5 0,87 1,10 4,60
L8W600T405 HT 60 80 400 122 2880 84,0 0,85 1,20 4,93 45 25 10 5,5
415 121 2895 84,5 0,82 1,30 5,25
380 141 2870 82,5 0,85 1,03 4,55
L8W670T405 HT 67 90 400 137 2885 83,0 0,83 1,13 4,89 45 25 16 5,5
415 133 2895 83,5 0,8 1,24 5,24
380 156 2905 82,5 0,86 1,02 4,55
L8W750T405 HT 75 100 400 152 2915 83,0 0,83 1,12 4,85 45 35 16 5,5
415 147 2925 83,5 0,81 1,21 5,15
380 171 2875 84,5 0,86 0,95 3,79
L8W830T405 HT 83 110 400 166 2885 85,0 0,84 1,04 4,30 45 35 16 5,5
415 161 2910 85,5 0,82 1,13 4,82
* Ts/Tn = ratio between starting torque and nominal torque. l8w-ht-2p50-en_a_te

63
64
10” Water filled submersible motors.
Submersible The robust design together with excellent choise of materials
ensures optimal performance, ease of installation and reliability
motors
in all applications. For extremely demanding operation as high
water temperature or aggressive environments special versions
are available.
L10W
Series
SPECIFICATIONS
SPECIFICATIONS SPECIAL VERSIONS
• Stainless steel outer sleeve. • Motors with double cable outlet for
• Rewindable stator stator. star/delta start.
• Class Y insulation
insulation. • L10WN series
series: complete range
• Protection class: IP68
IP68. available realized of AISI 316
• Compensating bellows for internal stainless steel.
liquid expansion. • L10WR series
series: complete range
• Axial load supported by Kingsbury available realized of Duplex
type thrust bearing. stainless steel.
• Mechanical seal • HT series
series: complete range
protected by sand guard. available for all the L10W/N/R
• Maximum immersion depth depth: construction, realized for applications
350 m. in high temperature environments
• Maximum number of starts per up to 60°C
(up 60°C) or under inverter.
hour at regular intervals: 8.
• Maximum supply voltage
OPTIONAL FEATURES
FEATURES
variations allowed : ±10%.
• Silicon Carbide mechanical seal.
• Maximum water temperature
temperature:
• Special voltages.
30°C.
Max. temperature applies to motors
ACCES SORIES
ACCESSORIES
working in a installation capable of
• Temperature sensor PT 100 / PTC
PTC.
delivering a flow of water around the
motor jacket of at least 0,5 m/s.
• Axial thrust
thrust:
65000 N from 93 to150 kW.
• Power supply cable suitable
for drinkable water.
• Versions
ersions:
- Three-phase:
93 to 150 kW 380-415 V, 50 Hz.
• Horizontal operation
operation:
valid for all versions provided that the
direction of the axial thrust generated
by the impellers is always from the
pump to the motor.

‰ Rewindable
stator

‰ Thrust bearing
Kingsbury
type

‰ Mechanical
seal

65
L10W - L10WN - L10WR MOTOR SERIES
MOTOR CROS S SECTION
CROSS

66
L10W MOTOR SERIES: TABLE OF MATERIALS
L10W T ABLE OF MA
TABLE TERIALS
MATERIALS
REF. PART MATERIAL DESIGNATION
N° EUROPE USA
1 Upper bracket Cast iron EN-GJL-200 Class 25 B
2 Spacer Cast iron EN-GJL-200 Class 25 B
3 Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4 Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5 Cable EPR
6 Cable gland plate Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
7 Cable gland EPDM
8 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10 Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
11 Mechanical seal Carbon graphite / Aluminium oxide
12 Bush bearings Carbon graphite
13 Elastomers NBR
14 Motor sleeve Stainless steel EN 10088-1-X2CrNi19-11 (1.4306) AISI304L
15 Lower bracket Cast iron EN-GJL-200 Class 25 B
16 Thrust bearing bracket Cast iron EN-GJL-200 Class 25 B
17 Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18 Diaphragm EPDM
19 Lower cover Cast iron EN-GJL-200 Class 25 B
20 Bolts and screws Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
L10WN
CoolingMOTOR
liquid SERIES:
Water + TABLE
antifreezeOF MATERIALS
L10WN TABLE OF MA
TABLE TERIALS
MATERIALS L10w-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1 Upper bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
2 Spacer Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
3 Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4 Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
5 Cable EPR
6 Cable gland plate Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
7 Cable gland EPDM
8 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10 Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
11 Mechanical seal Carbon graphite / Aluminium oxide
12 Bush bearings Carbon graphite
13 Elastomers NBR
14 Motor sleeve Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
15 Lower bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
16 Thrust bearing bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
17 Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18 Diaphragm EPDM
19 Lower cover Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
20 Bolts and screws Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
L10WR
CoolingMOTOR
liquid SERIES:
Water +TABLE
antifreezeOF MATERIALS
L10WR TABLE OF MA
TABLE TERIALS
MATERIALS L10wn-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1 Upper bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
2 Spacer Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
3 Filling plug + OR Duplex s. s.+NBR EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
4 Vent valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
5 Cable EPR
6 Cable gland plate Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
7 Cable gland EPDM
8 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Removable sand guard Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
10 Mechanical seal cover Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
11 Mechanical seal Carbon graphite / Aluminium oxide
12 Bush bearings Carbon graphite
13 Elastomers NBR
14 Motor sleeve Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
15 Lower bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
16 Thrust bearing bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
17 Filling valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
18 Diaphragm EPDM
19 Lower cover Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
20 Bolts and screws Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cooling liquid Water + antifreeze
L10wr-2p50-en_a_tm

67
L10W MOTOR SERIES
IDENTIFICATION CODE
IDENTIFICATION
L10W 1500 T 40 5 /_ HT
HIGH TEMPERATURE

VERSION
5 = 50 Hz
6 = 60 Hz

RATED VOLTAGE
T = THREE-PHASE
RATED POWER IN kW x 10
L10W (CAST IRON STANDARD VERSION)
L10WN (AISI 316 VERSION)
L10WR (DUPLEX VERSION)

EXAMPLE : L10W1500T405/A HT

L10W MOTOR :
RATED POWER 150 kW; THREE-PHASE;
RATED VOLTAGE 400 V; 50 Hz; /A VERSION; HIGH TEMPERATURE

RATING PLA
RATING TE
PLATE

LEGEND
1 - Motor type 7 - Weight
2 - Code 8 - Maximum immersion depht
3 - Maximum water temperature 9 - Operating characteristics
4 - Minimum water velocity 10 - Production date
5 - Insulation class 11 - Serial number
6 - Protection class 12 - Characteristics at service factor

68
L10W MOTOR SERIES
DIMENSIONS AND WEIGHTS AT 50 Hz
AT

DIMENSIONI E PESI MOTORI L10W - 2 poli 50 Hz

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L10W930T405 93 125 1562 360
L10W1100T405 110 150 1702 401
L10W1300T405 130 175 1852 448
L10W1500T405 150 200 1982 487
DIMENSIONI E PESI MOTORI L10W HT - 2 poli 50 Hz
l10w-2p50-en_a_td

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L10W830T405 HT 83 110 1562 360
L10W930T405 HT 93 125 1702 401
L10W1100T405 HT 110 150 1852 448
L10W1300T405 HT 130 175 1982 487
l10w-ht-2p50-en_a_td

69
L10W MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICSS AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 191 2895 83,0 0,87 1,02 5,14
L10W930T405 93 125 400 184 2910 83,0 0,85 1,12 5,55 30 35 25 5
415 180 2915 84,0 0,84 1,21 5,95
380 235 2900 83,5 0,86 1,20 4,77
L10W1100T405 110 150 400 225 2910 83,5 0,84 1,32 5,17 30 50 25 5
415 220 2920 84,5 0,82 1,43 5,57
380 270 2895 84,0 0,86 1,29 4,84
L10W1300T405 130 175 400 263 2915 83,0 0,85 1,42 5,22 30 50 25 5
415 255 2915 85,5 0,83 1,54 5,60
380 308 2905 83,0 0,86 1,26 4,77
L10W1500T405 150 200 400 295 2915 83,0 0,85 1,38 5,20 30 70 25 5
415 285 2925 84,0 0,84 1,50 5,63
* Ts/Tn = ratio between starting torque and nominal torque. l10w-2p50-en_b_te

L10W HT MOTOR SERIES

CARATTERISTICHE DI FUNZIONAMENTO L10W HT A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICS S A T 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 170,2 2900 85,0 0,87 1,14 5,77
L10W830T405 HT 83 110 400 164,0 2915 85,0 0,85 1,25 6,22 45 35 25 5
415 160,4 2920 86,0 0,84 1,36 6,68
380 200,5 2905 86,0 0,84 1,42 5,59
L10W930T405 HT 93 125 400 192,0 2915 86,0 0,82 1,56 6,06 45 50 25 5
415 187,7 2925 87,0 0,8 1,69 6,53
380 233,0 2900 87,0 0,82 1,53 5,61
L10W1100T405 HT 110 150 400 227,0 2920 86,0 0,81 1,68 6,05 45 50 25 5
415 220,1 2920 88,6 0,79 1,82 6,49
380 288 2920 85,0 0,83 1,46 5,10
L10W1300T405 HT 130 175 400 276 2930 85,0 0,82 1,60 5,56 45 70 25 5
415 267 2940 86,0 0,81 1,74 6,02
* Ts/Tn = ratio between starting torque and nominal torque. l10w-ht-2p50-en_a_te

70
12” Water filled submersible motors.
Submersible The robust design together with excellent choise of materials
ensures optimal performance, ease of installation and reliability
motors
in all applications. For extremely demanding operation as high
water temperature or aggressive environments special versions
are available.
L12W
Series
SPECIFICATIONS
SPECIFICATIONS SPECIAL VERSIONS
• Stainless steel outer sleeve. • Motors with double cable outlet for
• Rewindable stator stator. star/delta start.
• Class Y insulation
insulation. • L12WN series
series: complete range
• Protection class: IP68
IP68. available realized of AISI 316
• Compensating bellows for internal stainless steel.
liquid expansion. • L12WR series
series: complete range
• Axial load supported by Kingsbury available realized of Duplex
type thrust bearing. stainless steel.
• Mechanical seal • HT series
series: complete range
protected by sand guard. available for all the L12W/N/R
• Maximum immersion depth depth: construction, realized for applications
350 m. in high temperature environments
• Maximum number of starts per up to 60°C
(up 60°C) or under inverter.
hour at regular intervals: 4.
• Maximum supply voltage OPTIONAL FEATURES
FEATURES
variations allowed : ±10%. • Silicon Carbide mechanical seal.
• Maximum water temperature
temperature: • Special voltages.
30°C.
Max. temperature applies to motors ACCES SORIES
ACCESSORIES
working in a installation capable of • Temperature sensor PT 100 / PTC
PTC.
delivering a flow of water around the
motor jacket of at least 0,5 m/s.
• Axial thrust
thrust:
65000 N from 185 to 300 kW.
• Power supply cable suitable
for drinkable water.
• Versions
ersions:
- Three-phase:
185 to 300 kW 380-415 V, 50 Hz.
• Horizontal operation
operation:
valid for all versions provided that the
direction of the axial thrust generated
by the impellers is always from the
pump to the motor.

‰ Rewindable
stator

‰ Thrust bearing
Kingsbury
type

‰ Mechanical
seal

71
L12W - L12WN - L12WR MOTOR SERIES
MOTOR CROS S SECTION
CROSS

72
L12W MOTOR SERIES: TABLE OF MATERIALS
L12W T ABLE OF MA
TABLE TERIALS
MATERIALS
REF. PART MATERIAL DESIGNATION
N° EUROPE USA
1 Upper bracket Cast iron EN-GJL-200 Class 25 B
2 Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
3 Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4 Cable EPR
5 Cable gland plate Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
6 Cable gland EPDM
7 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
8 Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
9 Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10 Mechanical seal Carbon graphite / Aluminium oxide
11 Bush bearings Carbon graphite
12 Elastomers NBR
13 Stator flanges Steel UNI 3158 - Fe 52
14 Motor sleeve Stainless steel EN 10088-1-X2CrNi19-11 (1.4306) AISI304L
15 Lower bracket Cast iron EN-GJL-200 Class 25 B
16 Thrust bearing bracket Cast iron EN-GJL-200 Class 25 B
17 Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18 Diaphragm EPDM
19 Lower cover Cast iron EN-GJL-200 Class 25 B
20 Bolts and screws Stainless steel EN 10088-1-X5CrNi18-10 (1.4301) AISI304
L12WN MOTOR SERIES: TABLE OF MATERIALS
Cooling liquid Water + antifreeze
L12WN T ABLE OF MA
TABLE TERIALS
MATERIALS
L12w-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1 Upper bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
2 Filling plug + OR Stainless steel+NBR EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
3 Vent valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
4 Cable EPR
5 Cable gland plate Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
6 Cable gland EPDM
7 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
8 Removable sand guard Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
9 Mechanical seal cover Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
10 Mechanical seal Carbon graphite / Aluminium oxide
11 Bush bearings Carbon graphite
12 Elastomers NBR
13 Stator flanges Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
14 Motor sleeve Stainless steel EN 10088-1-X2CrNiMo17-12-2 (1.4404) AISI 316L
15 Lower bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
16 Thrust bearing bracket Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
17 Filling valve Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
18 Diaphragm EPDM
19 Lower cover Stainless steel EN 10213-4 - GX5CrNiMo19-11-2 (1.4408) ASTM CF-8M (AISI 316 cast)
20 Bolts and screws Stainless steel EN 10088-1-X5CrNiMo17-12-2 (1.4401) AISI 316
L12WR
CoolingMOTOR
liquid SERIES:
Water +TABLE
antifreezeOF MATERIALS
L12WR TABLE OF MA
TABLE TERIALS
MATERIALS
L12wn-2p50-en_a_tm

REF. PART MATERIAL DESIGNATION

N° EUROPE USA
1 Upper bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
2 Filling plug + OR Duplex s. s.+NBR EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
3 Vent valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
4 Cable EPR
5 Cable gland plate Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
6 Cable gland EPDM
7 Shaft end Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
8 Removable sand guard Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
9 Mechanical seal cover Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
10 Mechanical seal Carbon graphite / Aluminium oxide
11 Bush bearings Carbon graphite
12 Elastomers NBR
13 Stator flanges Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
14 Motor sleeve Stainless steel EN 10088-1X1NiCrMoCu25-20-5 (1.4539) AISI 904L
15 Lower bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
16 Thrust bearing bracket Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
17 Filling valve Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
18 Diaphragm EPDM
19 Lower cover Duplex stainless steel EN 10213-4-GX2CrNiMoCuN25-6-3-3 (1.4517)
20 Bolts and screws Duplex stainless steel EN 10088-1-X2CrNiMoN22-5-3 (1.4462) A276/A790-S31803
Cooling liquid Water + antifreeze
L12wr-2p50-en_a_tm

73
L12W MOTOR SERIES
IDENTIFICATION CODE
IDENTIFICATION
L12W 3000 T 40 5 /_ HT
HIGH TEMPERATURE

VERSION
5 = 50 Hz
6 = 60 Hz

RATED VOLTAGE
T = THREE-PHASE
RATED POWER IN kW x 10
L12W (CAST IRON STANDARD VERSION)
L12WN (AISI 316 VERSION)
L12WR (DUPLEX VERSION)

EXAMPLE : L12W3000T405/A HT

L12W MOTOR :
RATED POWER 300 kW; THREE-PHASE;
RATED VOLTAGE 400 V; 50 Hz; /A VERSION; HIGH TEMPERATURE

RATING PLA
RATING TE
PLATE

LEGEND
1 - Motor type 7 - Weight
2 - Code 8 - Maximum immersion depht
3 - Maximum water temperature 9 - Operating characteristics
4 - Minimum water velocity 10 - Production date
5 - Insulation class 11 - Serial number
6 - Protection class 12 - Characteristics at service factor

74
L12W MOTOR SERIES
DIMENSIONS AND WEIGHTS AT 50 Hz
AT

DIMENSIONI E PESI MOTORI L12W - 2 poli 50 Hz

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L12W1850T405 185 250 1739 552
L12W2200T405 220 300 1889 616
L12W2600T405 260 350 2039 680
L12W3000T405 300 400 2189 745
l12w-2p50-en_a_td
DIMENSIONI E PESI MOTORI L12W - 2 poli 50 Hz

MOTOR RATED DIMENSIONS (mm) WEIGHT

TYPE POWER
kW HP L kg
L12W1500T405 HT 150 200 1739 552
L12W1850T405 HT 185 250 1889 616
L12W2200T405 HT 220 300 2039 680
L12W2600T405 HT 260 350 2189 745
l12w-ht-2p50-en_a_td

75
L12W MOTOR SERIES
CARATTERISTICHE DI FUNZIONAMENTO A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICSS AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 380 2895 84,0 0,87 1,28 5,57
L12W1850T405 185 250 400 370 2905 84,0 0,86 1,41 5,99 30 70 50 5
415 360 2915 84,5 0,86 1,53 6,40
380 470 2910 84,5 0,86 1,04 4,60
L12W2200T405 220 300 400 456 2925 84,5 0,85 1,14 5,01 30 95 50 5
415 435 2930 85,5 0,83 1,24 5,42
380 525 2875 85,0 0,87 0,96 4,10
L12W2600T405 260 350 400 512 2890 85,0 0,85 1,06 4,39 30 120 70 5
415 498 2910 86,0 0,83 1,15 4,67
380 620 2880 85,0 0,87 0,90 4,10
L12W3000T405 300 400 400 594 2900 85,0 0,85 0,99 4,50 30 2x70 70 5
415 570 2910 86,0 0,84 1,08 4,90
* Ts/Tn = ratio between starting torque and nominal torque. l12w-2p50-en_c_te

L12W HT MOTOR SERIES

CARATTERISTICHE DI FUNZIONAMENTO L12W HT A 50 Hz
THREE-PHASE OPERA TING CHARACTERISTIC
OPERATING CHARACTERISTICS S AT 50 Hz
AT
MOTOR RATED RATED OPERATING CHARACTERISTICS DIRECT MAX CABLE TYPE
TYPE POWER VOLTAGE AT RATED POWER START WATER
RATED TEMPERATURE
2
THREE-PHASE CURRENT Sec. (mm )
kW HP V A rpm η% cosϕ Ts/Tn* Is/In °C DOL Y/D L (m)
380 328,6 2930 87,0 0,82 1,60 6,44
L12W1500T405 HT 150 200 400 320,0 2940 87,0 0,81 1,75 6,92 45 70 50 5
415 311,4 2950 87,5 0,81 1,91 7,40
380 379,3 2915 87,0 0,83 1,24 5,70
L12W1850T405 HT 185 250 400 368,0 2930 87,0 0,82 1,36 6,21 45 95 50 5
415 351,1 2935 88,0 0,8 1,48 6,72
380 438,9 2915 88,0 0,86 1,15 4,90
L12W2200T405 HT 220 300 400 428,0 2930 88,0 0,84 1,26 5,25 45 120 70 5
415 416,3 2950 89,0 0,82 1,38 5,59
380 546 2895 87,0 0,84 1,04 4,66
L12W2600T405 HT 260 350 400 523 2915 87,0 0,82 1,15 5,11 45 2x70 70 5
415 502 2925 88,0 0,81 1,25 5,57
* Ts/Tn = ratio between starting torque and nominal torque. l12w-ht-2p50-en_a_te

76
ACCES SORIES
ACCESSORIES

ISO Threaded Flanges ..................................................................................................................... 78

Supporting Collars .......................................................................................................................... 80

Motor - Control Panle Combination Table ........................................................................................ 81

Electrical Panels ...............................................................................................................................83

Level control panels ........................................................................................................................ 89

Level probe module ........................................................................................................................ 90

Lightning protection ....................................................................................................................... 91

Cooling shrouds ............................................................................................................................. 92

Booster shroud ............................................................................................................................... 94

77
ISO THREADED FLANGES

DIMENSIONI FLANGE ISO PER POMPE SERIE Z

Dimensions (mm)
PUMP THREADING
Flange according to EN 1092-1
TYPE G
DN PN ØD Ød Øk b Ø d2 Z L L1
150 10 ÷ 16 285 212 240 22 22 8 198 40
150 25 ÷ 40 300 218 250 28 26 8 218 40
150 63 345 218 280 36 33 8 238 40
Z10150
EN 10226-1 200 10 340 268 295 24 22 8 357 40
Z10220
R6 200 16 340 268 295 24 22 12 357 40
Z10275
200 25 360 278 310 30 26 12 375 40
200 40 375 285 320 34 30 12 383 40
200 63 415 285 345 42 36 12 405 40
200 10 340 - 295 26 22 8 150 55
200 16 340 - 295 30 22 12 150 55
ANSI B1.20.1
Z12340 200 25 360 - 310 34 26 12 150 55
API 8 NPT
200 40 375 - 320 40 30 12 150 55
200 63 415 - 345 42 36 12 150 55
Material : Stainless steel EN 10088-1 - X6CrNiMoTi17-12-2 (1.4571) AISI 316Ti. (Other materials available on request). z-flange-r-en_b_td

78
ANSI (API) THREADED FLANGE

DIMENSIONI FLANGE ASME (ANSI) POMPE SERIE Z

Dimensions (mm)
PUMP THREADING
Flange according to ASME B16.5
TYPE EN 10226-1
G DN Class ØD Ød Øk b Ø d2 Z L L1
6" 150 280 216 241 25 22 8 232 40
6" 300 317 216 270 37 22 12 242 40
Z10150
6" 600 356 216 292 54 29 12 266 40
Z10220 R6
8" 150 343 270 298 28 22 8 397 40
Z10275
8" 300 381 270 330 41 25 12 406 40
8" 600 419 270 349 62 32 12 434 40
Material : Stainless steel EN 10088-1 - X6CrNiMoTi17-12-2 (1.4571) AISI 316Ti. (Other materials available on request). z-flange-api-en_b_td

79
CARRYING CLAMPS

DIMENSIONI CLAMP PER POMPE SOMMERSE

CARRYING CLAMPS PIPE WEIGHT

NOMINAL PIPE DIAMETER
DN Dimensions (mm) Pmax
(1)
Flanged Threaded Water

A B C E SCREW kg kg/m kg/m kg/m

65 R 2 1/2" 50 15 600 130 M16x90 1300 6,7 8,0 3,3
80 R 3" 80 15 600 180 M20x70 3400 8,4 10,5 5,0
100 R 4" 80 15 600 180 M20x110 3400 20,5 15,0 7,9
125 R 5" 100 20 600 260 M24x90 7250 27,5 18,5 12,3
150 R 6" 100 20 600 260 M24x130 7250 33,0 22,0 17,6
175 R 7" 120 25 800 360 M30x110 9750 27,0 25,5 24,0
200 R 8" 120 25 800 360 M30x150 9750 33,0 34,0 31,5
250 R 10" 120 25 800 360 M30x220 9750 48,0 48,0 49,0
1) Max admissible weight. clamp-en_b_td

NOTE. Two sets of clamps are necessary for the installation of one unit.
Material : EN 10027-1-S235JR (1.0038) painted.

80
L6W - L8W MOTOR SERIES
TABELLE INDICATIVE DI ABBINAMENTO MOTORE - QUADRO
MOTOR - CONTROL P ANEL COMBINA
PANEL TION T
COMBINATION ABLE
TABLE
MOTOR TYPE RATED RATED PANEL TYPE
L6W - 6" POWER CURRENT
THREE-PHASE 380-415 V
kW HP A QTD/… Q3D/… Q3I/… Q3A/… Q3Y/… Q3SF/…
4 5,5 9,89 …40-75 …40-75 …40-75 …40-75 …40-75 …75
5,5 7,5 12,7 …40-75 …40-75 …40-75 …40-75 …40-75 …75
7,5 10 17,0 …75-92 …75-92 …75-92 …75-92 …75-92 …150
9,3 12,5 20,5 - …92-110 …92-110 …92-110 …92-110 …150
11 15 24,2 - …110-150 …110-150 …110-150 …110-150 …150
13 17,5 28,1 - …110-150 …110-150 …110-150 …110-150 …150
15 20 32,1 - …150-185 …150-185 …150-185 …150-185 …220
18,5 25 38,5 - …185-220 …185-220 …185-220 …185-220 …220
22 30 47,3 - …220-300 …220-300 …220-300 …220-300 …300
26 35 56,5 - …220-300 …220-300 …220-300 …220-300 …300
30 40 63,8 - …300-370 …300-370 …300-370 …300-370 …370
37 50 81,8 - - …370-450 …370-450 …370-450 …450
MOTOR TYPE 4 5,5 10,5 …40-75 …40-75 …40-75 …40-75 …40-75 …75
L6W HT - 6" 5,5 7,5 13,4 …40-75 …40-75 …40-75 …40-75 …40-75 …75
THREE-PHASE 7,5 10 17,3 …75-92 …75-92 …75-92 …75-92 …75-92 …150
9,3 12,5 20,8 - …92-110 …92-110 …92-110 …92-110 …150
11 15 23,9 - …110-150 …110-150 …110-150 …110-150 …150
13 17,5 28,4 - …110-150 …110-150 …110-150 …110-150 …150
15 20 32,5 - …150-185 …150-185 …150-185 …150-185 …220
18,5 25 41,6 - …185-220 …185-220 …185-220 …185-220 …220
22 30 49,7 - …220-300 …220-300 …220-300 …220-300 …300
26 35 55,8 - …220-300 …220-300 …220-300 …220-300 …300
30 40 68,8 - …300-370 …300-370 …300-370 …300-370 …370
TABELLA ABBINAMENTO POMPA-QUADRO COMANDO
For different voltages, please contact our sales network. L6w-2p50-en_c_tc

MOTOR TYPE RATED RATED PANEL TYPE

L8W - 8" POWER CURRENT
THREE-PHASE 380-415 V
kW HP A Q3D/… Q3I/… Q3A/… Q3SF/…
30 40 65 …300-370 …300-370 …300-370 …370
37 50 81 - …370-450 …370-450 …450
45 60 92 - …450-550 …450-550 …550
52 70 110 - …550-750 …550-750 …590
55 75 118 - …550-750 …550-750 …590
60 80 124 - …550-750 …550-750 …750
67 90 138 - …750-900 …750-900 …900
75 100 156 - …750-900 …750-900 …900
83 110 172 - …750-900 …750-900 …900
93 125 192 - …900-1100 …900-1100 …1100
MOTOR TYPE 30 40 66,6 …300-370 …300-370 …300-370 …370
L8W HT - 8" 37 50 77,5 - …370-450 …370-450 …450
THREE-PHASE 45 60 97,8 - …450-550 …450-550 …550
52 70 110 - …550-750 …550-750 …590
55 75 117 - …550-750 …550-750 …590
60 80 127 - …550-750 …550-750 …750
67 90 141 - …750-900 …750-900 …900
75 100 156 - …750-900 …750-900 …900
83 110 171 - …750-900 …750-900 …900
For different voltages, please contact our sales network. L8w-2p50-en_b_tc

81
L10W - L12W MOTOR SERIES
TABELLA ABBINAMENTO POMPA-QUADRO COMANDO
MOTOR - CONTROL P ANEL COMBINA
PANEL TION T
COMBINATION ABLE
TABLE
MOTOR TYPE RATED RATED PANEL TYPE
L10W - 10" POWER CURRENT
THREE-PHASE 380-415 V
kW HP A Q3I/… Q3A/… Q3SF/…
93 125 191 …900-1100 …900-1100 …1100
110 150 235 …1100-1320 …1100-1320 …1100
130 175 270 …1320-1600 …1320-1600 (1)
150 200 308 …1600-2000 …1600-2000 (1)
MOTOR TYPE 83 110 170,2 …750-900 …750-900 …900
L10W HT - 10" 93 125 200,5 …900-1100 …900-1100 …1100
THREE-PHASE 110 150 233,0 …1100-1320 …1100-1320 …1100
130 175 288,0 …1320-1600 …1320-1600 (1)
(1) On request. L10w-2p50-en_c_tc

TABELLA ABBINAMENTO POMPA-QUADRO COMANDO

For different voltages, please contact our sales network.

MOTOR TYPE RATED RATED PANEL TYPE

L12W - 12" POWER CURRENT
THREE-PHASE 380-415 V
kW HP A Q3I/… Q3A/… Q3SF/…
185 250 380 …1600-2000 …1600-2000 (1)
220 300 470 …2500-3150 …2500-3150 (1)
260 350 525 …2500-3150 …2500-3150 (1)
300 400 620 (1) (1) (1)
MOTOR TYPE 150 200 328,6 …1600-2000 …1600-2000 (1)
L12W HT - 12" 185 250 379,3 …1600-2000 …1600-2000 (1)
THREE-PHASE 220 300 438,9 …2000-2500 …2000-2500 (1)
260 350 546,0 …2500-3150 …2500-3150 (1)
(1) On request. L12w-2p50-en_c_tc

For different voltages, please contact our sales network.

82
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel

QTD Series SPECIFICATIONS

SPECIFICATIONS OPTIONAL
• Control through an external ACCES SORIES
ACCESSORIES
enable contact. • VR3 three-phase module for
• Supply voltage: overvoltage protection (lightning
3 x 400 V ±10%. protector).
• Frequency: 50/60 Hz. • KSL series 24 V level kit.
• Power: 0,25 to 9,2 kW. Probe module for protection against
• Direct motor start. dry running (set of three electrodes
• Short-circuit and overload protection. included in the supply).
• Protection class: IP54.
• Ambient temperature: -5 to +40 °C SELECTION
(according to EN 60439-1). • For a suitable choice of control panel,
• Maximum relative humidity: 50% at be sure the electrical input of the
+40°C, provided that no condensation motor (Ampere) is included in the
occurs (according to EN 60439-1). rated current value mentioned in the
• Wall mounted. table below.
• Metal enclosure.
• Ready for installation of dry
running control float or pressure
switch (to be ordered separately).
• Power and thermal overload
indicator lights.

A C

0
1

LINEA
POWER
B
TERMICO
OVERLOAD

SERIE QTD

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
QTD/02-03 3 x 400 V ± 10 % 0,25-0,37 0,33-0,50 0,63 ÷ 1 235 265 150 5,8
QTD/03-05 3 x 400 V ± 10 % 0,37-0,55 0,55-0,75 1 ÷ 1,6 235 265 150 5,8
QTD/05-07 3 x 400 V ± 10 % 0,55-0,75 0,75-1 1,6 2,5 235 265 150 5,8
QTD/07-15 3 x 400 V ± 10 % 0,75-1,5 1-2 2,5 4 235 265 150 5,8
QTD/15-22 3 x 400 V ± 10 % 1,5-2,2 2-3 4 ÷ 6,3 235 265 150 5,8
QTD/22-40 3 x 400 V ± 10 % 2,2-4 3-5,5 6,3 ÷ 10 235 265 150 5,8
QTD/40-75 3 x 400 V ± 10 % 4-7,5 5,5-10 10 ÷ 16 235 265 150 5,8
QTD/75-92 3 x 400 V ± 10 % 7,5-9,2 10-12,5 16 ÷ 20 235 265 150 5,8
CB-QTD-en_c_te

83
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel

Q3D Series SPECIFICATIONS

SPECIFICATIONS • Ready for installation of dry running
• Manual control through an control float or pressure switch
Auto/Man selector switch. (to be ordered separately).
• Automatic control through an Can be equipped with electronic
external enable contact. protection module with electrodes.
• Supply voltage:
3 x 400 V ±10%. OPTIONAL
• Frequency: 50/60 Hz. ACCES SORIES
ACCESSORIES
• 24 V AC low voltage auxiliary circuit. • KSL series 24 V level kit.
• Power: 0,25 to 37 kW. Probe module for protection against
• Direct motor start. dry running (set of three electrodes
• Short-circuit and overload protection. included in the supply).
• Protection class: IP54. • Float.
• Ambient temperature: -5 to +40 °C • Pressure switch.
(according to EN 60439-1). • VR3/SCA3 three-phase module for
• Maximum relative humidity: 50% at overvoltage protection (lightning
+40°C, provided that no condensation protector).
occurs (according to EN 60439-1).
• Wall mounted. A C

• Metal enclosure.
• Power, pump running, thermal
overload and dry running indicator V 300
500

L1-L2
L2-L3
L3-L1
A 150
200

lights.
50 0 25

0 0

M 0 A

SERIE Q3D

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
Q3D/02-03 3 x 400 V ± 10 % 0,25-0,37 0,33-0,50 0,63 ÷ 1 300 400 200 15
Q3D/03-05 3 x 400 V ± 10 % 0,37-0,55 0,5-0,75 1 ÷ 1,6 300 400 200 15
Q3D/05-07 3 x 400 V ± 10 % 0,55-0,75 0,75-1 1,6 ÷ 2,5 300 400 200 15
Q3D/07-15 3 x 400 V ± 10 % 0,75-1,5 1-2 2,5 ÷ 4 300 400 200 15
Q3D/15-22 3 x 400 V ± 10 % 1,5-2,2 2-3 4 ÷ 6,3 300 400 200 15
Q3D/22-40 3 x 400 V ± 10 % 2,2-4 3-5,5 6,3 ÷ 10 300 400 200 15
Q3D/40-75 3 x 400 V ± 10 % 4-7,5 5,5-10 10 ÷ 16 300 400 200 15
Q3D/75-92 3 x 400 V ± 10 % 7,5-9,2 10-12,5 16 ÷ 20 300 400 200 15
Q3D/92-110 3 x 400 V ± 10 % 9,2-11 12,5-15 20 ÷ 25 300 400 200 20
Q3D/110-150 3 x 400 V ± 10 % 11-15 15-20 22 ÷ 32 400 500 200 20
Q3D/150-185 3 x 400 V ± 10 % 15-18,5 20-25 28 ÷ 40 400 500 200 20
Q3D/185-220 3 x 400 V ± 10 % 18,5-22 25-30 36 ÷ 50 400 600 200 27
Q3D/220-300 3 x 400 V ± 10 % 22-30 30-40 45 ÷ 63 400 600 200 27
Q3D/300-370 3 x 400 V ± 10 % 30-37 40-50 57 ÷ 75 400 600 200 27
CB-Q3D-en_a_te

84
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel
SPECIFICATIONS
SPECIFICATIONS • Ready for installation of dry running
• Manual control through an control float or pressure switch
Auto/Man selector switch. (to be ordered separately).
Q3Y Series • Automatic control through an Can be equipped with electronic
external enable contact. protection module with electrodes.
• Supply voltage:
3 x 400 V ±10%. OPTIONAL
• Frequency: 50/60 Hz. ACCES SORIES
ACCESSORIES
• 24 V AC low voltage auxiliary circuit. • KSL series 24 V level kit.
• Power: 4 to 315 kW. Probe module for protection against
• Star-delta starting. dry running (set of three electrodes
• Short-circuit and overload protection. included in the supply).
• Protection class: IP54. • Float.
• Ambient temperature: -5 to +40 °C • Pressure switch.
(according to EN 60439-1). • VR3/SCA3 three-phase module for
• Maximum relative humidity: 50% at overvoltage protection (lightning
+40°C, provided that no condensation protector).
occurs (according to EN 60439-1). A C
• Wall mounted.
• Metal enclosure.
• Power, pump running, thermal V 500
A 200

overload and dry running indicator

300 150

L2-L3
L1-L2 L3-L1

50 0 25

0 0

lights.

M 0 A

SERIE Q3Y

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
Q3Y/40-75 3 x 400 V ± 10 % 4-7,5 5,5-10 10 ÷ 16 400 600 200 23
Q3Y/75-92 3 x 400 V ± 10 % 7,5-9,2 10-12,5 16 ÷ 20 400 600 200 23
Q3Y/92-110 3 x 400 V ± 10 % 9,2-11 12,5-15 20 ÷ 25 400 600 200 23
Q3Y/110-150 3 x 400 V ± 10 % 11-15 15-20 22 ÷ 32 400 600 200 23
Q3Y/150-185 3 x 400 V ± 10 % 15-18,5 20-25 28 ÷ 40 400 600 200 23
Q3Y/185-220 3 x 400 V ± 10 % 18,5-22 25-30 36 ÷ 50 500 700 200 32
Q3Y/220-300 3 x 400 V ± 10 % 22-30 30-40 45 ÷ 63 500 700 200 32
Q3Y/300-370 3 x 400 V ± 10 % 30-37 40-50 57 ÷ 75 600 800 250 68
Q3Y/370-450 3 x 400 V ± 10 % 37-45 50-60 70 ÷ 90 600 800 250 80
Q3Y/450-550 3 x 400 V ± 10 % 45-55 60-75 80 ÷ 108 600 900 250 80
Q3Y/550-750 3 x 400 V ± 10 % 55-75 75-100 105 ÷ 138 600p 1300p 300p 109
Q3Y/750-900 3 x 400 V ± 10 % 75-90 100-125 138 ÷ 185 600p 1300p 300p 109
Q3Y/900-1100 3 x 400 V ± 10 % 90-110 125-150 175 ÷ 210 600p 1500p 300p 120
Q3Y/1100-1320 3 x 400 V ± 10 % 110-132 150-180 210 ÷ 260 800p 1700p 400p 130
Q3Y/1320-1600 3 x 400 V ± 10 % 132-160 180-218 250 ÷ 305 800p 1700p 400p 130
Q3Y/1600-2000 3 x 400 V ± 10 % 160-200 218-273 290 ÷ 400 800p 1900p 400p 140
Q3Y/2000-2500 3 x 400 V ± 10 % 200-250 273-340 400 ÷ 460 1000p 1900p 400p 180
Q3Y/2500-3150 3 x 400 V ± 10 % 250-315 340-430 450 ÷ 580 1000p 1900p 400p 180
Dimensions note : P indicates floor mounted control panel. CB-Q3Y-en_c_te

85
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel
SPECIFICATIONS
SPECIFICATIONS • Ready for installation of dry running
• Manual control through an control float or pressure switch
Auto/Man selector switch. (to be ordered separately).
Q3I Series • Automatic control through an Can be equipped with electronic
external enable contact. protection module with electrodes.
• Supply voltage:
3 x 400 V ±10%. OPTIONAL
• Frequency: 50/60 Hz. ACCES SORIES
ACCESSORIES
• 24 V AC low voltage auxiliary circuit. • KSL series 24 V level kit.
• Power: 4 to 315 kW. Probe module for protection against
• Impedance start. dry running (set of three electrodes
• Short-circuit and overload protection. included in the supply).
• Protection class: IP54. • Float.
• Ambient temperature: -5 to +40 °C • Pressure switch.
(according to EN 60439-1). • VR3/SCA3 three-phase module for
• Maximum relative humidity: 50% at overvoltage protection (lightning
+40°C, provided that no condensation protector).
occurs (according to EN 60439-1). A C
• Wall mounted.
• Metal enclosure.
• Power, pump running, thermal V 500
A 200

overload and dry running indicator

300 150

L2-L3
L1-L2 L3-L1

50 0 25

0 0

lights.

M 0 A

SERIE Q3I

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
Q3I/40-75 3 x 400 V ± 10 % 4-7,5 5,5-10 10 ÷ 16 400 600 250 35
Q3I/75-92 3 x 400 V ± 10 % 7,5-9,2 10-12,5 16 ÷ 20 400 600 250 35
Q3I/92-110 3 x 400 V ± 10 % 9,2-11 12,5-15 20 ÷ 25 400 600 250 35
Q3I/110-150 3 x 400 V ± 10 % 11-15 15-20 22 ÷ 32 500 700 250 50
Q3I/150-185 3 x 400 V ± 10 % 15-18,5 20-25 28 ÷ 40 500 700 250 50
Q3I/185-220 3 x 400 V ± 10 % 18,5-22 25-30 36 ÷ 50 500 700 250 50
Q3I/220-300 3 x 400 V ± 10 % 22-30 30-40 45 ÷ 63 500 700 250 65
Q3I/300-370 3 x 400 V ± 10 % 30-37 40-50 57 ÷ 75 500 700 250 65
Q3I/370-450 3 x 400 V ± 10 % 37-45 50-60 70 ÷ 90 600 900 250 65
Q3I/450-550 3 x 400 V ± 10 % 45-55 60-75 80 ÷ 108 600p 1300p 300p 100
Q3I/550-750 3 x 400 V ± 10 % 55-75 75-100 105 ÷ 138 600p 1300p 300p 100
Q3I/750-900 3 x 400 V ± 10 % 75-90 100-125 138 ÷ 185 600p 1500p 300p 100
Q3I/900-1100 3 x 400 V ± 10 % 90-110 125-150 175 ÷ 210 800p 1700p 400p 100
Q3I/1100-1320 3 x 400 V ± 10 % 110-132 150-180 210 ÷ 260 800p 1700p 400p 150
Q3I/1320-1600 3 x 400 V ± 10 % 132-160 180-218 250 ÷ 305 800p 1700p 400p 150
Q3I/1600-2000 3 x 400 V ± 10 % 160-200 218-273 290 ÷ 400 800p 1900p 400p 160
Q3I/2000-2500 3 x 400 V ± 10 % 200-250 273-340 400 ÷ 460 1000p 1900p 400p 180
Q3I/2500-3150 3 x 400 V ± 10 % 250-315 340-430 450 ÷ 580 1000p 1900p 400p 200
Dimensions note : P indicates floor mounted control panel. CB-Q3I-en_c_te

86
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel
SPECIFICATIONS
SPECIFICATIONS • Ready for installation of dry running
• Manual control through an control float or pressure switch
Auto/Man selector switch. (to be ordered separately).
Q3A Series • Automatic control through an Can be equipped with electronic
external enable contact. protection module with electrodes.
• Supply voltage:
3 x 400 V ±10%. OPTIONAL
• Frequency: 50/60 Hz. ACCES SORIES
ACCESSORIES
• 24 V AC low voltage auxiliary circuit. • KSL series 24 V level kit.
• Power: 4 to 315 kW. Probe module for protection against
• Starting autotransformer. dry running (set of three electrodes
• Short-circuit and overload protection. included in the supply).
• Protection class: IP54. • Float.
• Ambient temperature: -5 to +40 °C • Pressure switch.
(according to EN 60439-1). • VR3/SCA3 three-phase module for
• Maximum relative humidity: 50% at overvoltage protection (lightning
+40°C, provided that no condensation protector).
occurs (according to EN 60439-1). A C
• Wall mounted.
• Metal enclosure.
• Power, pump running, thermal V 500
A 200

overload and dry running indicator

300 150

L2-L3
L1-L2 L3-L1

50 0 25

0 0

lights.

M 0 A

SERIE Q3A

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
Q3A/40-75 3 x 400 V ± 10 % 4-7,5 5,5-10 10 ÷ 16 500 700 250 50
Q3A/75-92 3 x 400 V ± 10 % 7,5-9,2 10-12,5 16 ÷ 20 500 700 250 50
Q3A/92-110 3 x 400 V ± 10 % 9,2-11 12,5-15 20 ÷ 25 500 700 250 50
Q3A/110-150 3 x 400 V ± 10 % 11-15 15-20 22 ÷ 32 500 700 250 50
Q3A/150-185 3 x 400 V ± 10 % 15-18,5 20-25 28 ÷ 40 500 700 250 50
Q3A/185-220 3 x 400 V ± 10 % 18,5-22 25-30 36 ÷ 50 500 700 250 50
Q3A/220-300 3 x 400 V ± 10 % 22-30 30-40 45 ÷ 63 600 900 300 80
Q3A/300-370 3 x 400 V ± 10 % 30-37 40-50 57 ÷ 75 600 900 300 80
Q3A/370-450 3 x 400 V ± 10 % 37-45 50-60 70 ÷ 90 600p 1300p 300p 90
Q3A/450-550 3 x 400 V ± 10 % 45-55 60-75 80 ÷ 108 600p 1500p 300p 120
Q3A/550-750 3 x 400 V ± 10 % 55-75 75-100 105 ÷ 138 600p 1500p 300p 120
Q3A/750-900 3 x 400 V ± 10 % 75-90 100-125 138 ÷ 185 600p 1700p 400p 150
Q3A/900-1100 3 x 400 V ± 10 % 90-110 125-150 175 ÷ 210 800p 1900p 400p 150
Q3A/1100-1320 3 x 400 V ± 10 % 110-132 150-180 210 ÷ 260 800p 1900p 400p 200
Q3A/1320-1600 3 x 400 V ± 10 % 132-160 180-218 250 ÷ 305 800p 1900p 400p 200
Q3A/1600-2000 3 x 400 V ± 10 % 160-200 218-273 290 ÷ 400 800p 1900p 400p 230
Q3A/2000-2500 3 x 400 V ± 10 % 200-250 273-340 400 ÷ 460 1000p 1900p 400p 230
Q3A/2500-3150 3 x 400 V ± 10 % 250-315 340-430 450 ÷ 580 1000p 1900p 400p 250
Dimensions note : P indicates floor mounted control panel. CB-Q3A-en_c_te

87
Three-phase APPLICATIONS
APPLICATIONS
Electric • Protection and control of a three-phase surface or
submersible electric pump.
Panel SPECIFICATIONS
SPECIFICATIONS Protections against phase failure /
• Manual control through an phase sequence / frequency out of
Auto/Man selector switch. limits on power supply line.
• Automatic control through an Low-voltage protection on auxiliary
external enable contact. circuits.
Q3SF Series • Supply voltage: Protection against starter
3 x 400 V ±10%. overtemperature / overload /
• Frequency: 50/60 Hz. malfunction.
• 24 V AC low voltage auxiliary circuit. Protection against overload / locked
• Power: 5,5 to 110 kW. rotor / current asymmetry on motor
• Softstart with torque control. side.
• Protection class: IP54. Short-circuit protection on inputs
• Ambient temperature: -5 to +40 °C and outputs.
• Maximum relative humidity: 50% at RS232 interface for remote control
+40°C, provided that no condensation and RS485 for use of remote
occurs (according to EN 60439-1). keypanel.
• Wall mounted. Incorporated by-pass contactor.
• Metal enclosure.
• Dry running indicator light. OPTIONAL
• Power - pump running - malfunction ACCES SORIES
ACCESSORIES
LEDs on starter keypanel. • KSL series 24 V level kit.
• ON/OFF selector switch for activation Probe module for protection against
of by-pass contactor. dry running (set of three electrodes
• Ready for installation of dry running included in the supply).
control float or pressure switch • Float.
(to be ordered separately). • Pressure switch.
Can be equipped with electronic • VR3/SCA3 three-phase module for
protection module with electrodes. overvoltage protection (lightning
protector).

A C

STATIC ST
STA ARTER
STARTER
CHARACTERISTIC
CHARACTERISTICSS
• Static starter for gradual start-up/ M 0 A

shutdown, featuring:
keypanel with liquid crystal display
showing voltage, absorbed current,
cos ϕ, operating hours, number of
B

starts, last twenty messages on

system status (events / alarms).

SERIE Q3SF

MODEL RATED RATED RATED DIMENSIONS WEIGHT

VOLTAGE POWER CURRENT A B C
V kW HP A mm mm mm Kg
Q3SF 75 3 x 400 V ± 10 % 5,5 - 7,5 7,5 -10 8,5 ÷ 17 400 600 250 35
Q3SF 150 3 x 400 V ± 10 % 9,2 - 15 12,5 - 20 15 ÷ 30 500 700 250 40
Q3SF 220 3 x 400 V ± 10 % 18,5 - 22 25 - 30 28 ÷ 45 500 700 250 40
Q3SF 300 3 x 400 V ± 10 % 30 40 42 ÷ 60 600 900 300 90
Q3SF 370 3 x 400 V ± 10 % 37 50 55 ÷ 75 600 900 300 90
Q3SF 450 3 x 400 V ± 10 % 45 60 70 ÷ 85 600 900 300 90
Q3SF 550 3 x 400 V ± 10 % 55 75 80 ÷ 110 600 900 300 90
Q3SF 590 3 x 400 V ± 10 % 59 80 105 ÷ 125 600 900 300 90
Q3SF 750 3 x 400 V ± 10 % 75 100 120 ÷ 142 600p 1700p 400p 120
Q3SF 900 3 x 400 V ± 10 % 90 125 135 ÷ 190 600p 1700p 400p 120
Q3SF 1100 3 x 400 V ± 10 % 110 150 185 ÷ 245 600p 1700p 400p 120
Dimensions note : P indicates floor mounted control panel. CB-Q3SF-en_b_te

88
Level APPLICATIONS
APPLICATIONS
Control • Accessory for electric pump control panels, suitable for tank
filling or drainage applications or for activation of audible
Panel
or visual alarms.

QCL5 Series SPECIFICATIONS

SPECIFICATIONS OPTIONAL
• Automatic control through probes. ACCES SORIES
ACCESSORIES
• Supply voltage: • Drop cable with circular cross section.
1 x 230 V ±10% or 1 x 24 V ±10%.
• Frequency: 50/60 Hz. For connection of the electrodes to the
• Voltage to probes: panel we recommend
15 V AC at 0,5 mA max.
TABELLA CAVI the following
cross sections:
• Switch contact 48 V AC at 3 A max
LENGHT CABLE SECTION
(250 W max).
m mm2
• Protection class: IP55.
0 50 0,5
• Ambient temperature: -5 to +40 °C
50 100 0,75
(according to EN 60439-1).
100 200 1,0
• Maximum relative humidity: 50% at
200 400 2,5
+40°C, provided that no condensation
occurs (according to EN 60439-1).
• Wall mounted. CB-CASEL-en_b_te

• Plastic enclosure. Three-pole cables can be used for short

• Electrodes suitable for water at a lenghts.
maximum temperature of 40°C. Otherwise we recommend the use of
• Set of three electrodes included in unipolar cables placed at suitable
the supply. distance from each other to prevent
the capacitive effect of the cable from
interfering with the proper operation
of the electronic module.

A C

B
Control box

SERIE QCL5

TYPE POWER SUPPLY CONTACT DIMENSIONS WEIGHT

VOLTAGE FREQUENCY POWER TYPE RANGE AxBxC
V Hz W V A mm Kg
QCL5/24 1 x 24 50/60 2
NO-C-NC 48 3 90 x 130 x 60 0,5
QCL5/230 1 x 230 50/60 2
CB-QCL5-en_a_te

89
Kit APPLICATIONS
APPLICATIONS
24 V Level • Accessory for electric panels.
Probe

KSL Series SPECIFICATIONS

SPECIFICATIONS OPTIONAL
• Electronic module for use of probes ACCES SORIES
ACCESSORIES
as protection against dry running. • Drop cable with circular cross section.
• Supply voltage:
1 x 24 V ±10% for model SLD/24. For connection of the electrodes to the
• Frequency: 50/60 Hz. panel we recommend
• Absorbed power: 3,5 VA max.
TABELLA CAVI the following
cross sections:
• Voltage to probes:
LENGHT CABLE SECTION
7,5 V AC at 0,4 mA max.
m mm2
• Switch contact 24 V AC at 5 A max
0 50 0,5
(250 W max).
50 100 0,75
• Designed for installation on Lowara
100 200 1,0
electric panels featuring DIN bar.
200 400 2,5
• Electrodes suitable for water at a
maximum temperature of 60°C.
CB-CASEL-en_b_te

Three-pole cables can be used for short

CONSTRUCTION lenghts.
CHARACTERISTIC
CHARACTERISTICSS Otherwise we recommend the use of
• Module made of plastic material unipolar cables placed at suitable
with DIN bar attachment. distance from each other to prevent
• Cables with quick plug-in connectors. the capacitive effect of the cable from
• Set of three electrodes included in interfering with the proper operation
the supply. of the electronic module.
• Electrodes with nylon 6 body,
stainless steel sensitive element
brass washer and nitrile rubber seal.

SERIE SLD

TYPE POWER SUPPLY CONTACT DIMENSIONS WEIGHT PANELS

MAIN POWER TYPE RANGE AxBxC
V VA V~ A mm Kg

QSCS-QM-QTD-Q3D-Q3Y-
KIT KSL/24 1x24 50/60 Hz 3,5 N0-C-NC 250 8 90 x 36 x 60 0,5
Q3A-Q3I-Q3SF

CB-SLD-en_b_te

90
Lightning APPLICATIONS
APPLICATIONS
Protection • Accessory for electric panels.

DPF Series
SPECIFICATIONS
SPECIFICATIONS
• Varistor for overvoltage protection of
single-phase lines. To be connected
between the phase and neutral
conductor.
• Operating voltage: 460 V AC.
• Maximum varistor voltage: 750 V
with 100 A peak current.

VR Series
SPECIFICATIONS
SPECIFICATIONS
• Varistors for overvoltage protection of
three-phase lines.
• To be connected between the phases
(VR3 model).
• Operating voltage: 460 V AC.
• Maximum varistor voltage: 750 V
with 100 A peak current.
• Designed for installation on Lowara
electric panels featuring DIN bar.

SCA3 Series
SPECIFICATIONS
SPECIFICATIONS
• Lightning arresters for overvoltage
protection of three-phase lines. To
be connected between the phases
and the heart conductor,
• Operating voltage: 500 V AC.
• Maximum varistor voltage: 2,5 kW
with 40 kA peak current.
• Designed for installation on Lowara
electric panels featuring DIN bar.

SERIE VR

TYPE VOLTAGE PANELS

V
DPF 1 x 220-240 50/60 Hz QSM - QSC - QSCS - QPC
KIT VR1 1 x 220-230 50/60 Hz QM - QDRM - QDRM2 - QDRMC - QDRMC2
KIT VR3 3 x 400 50/60 Hz QTD - QDR - QDR2 - Q3D
KIT SCA 3 3 x 400 50/60 Hz Q3Y-Q3A-Q3I-Q3SF-Q3D
CB-VR-en_c_te

91
COOLING SHROUDS

92
COOLING SHROUDS
Z10-Z12 PUMP SERIES
6”, 8”, 10” and 12” MOTORS COMBINA
DIMENSIONI E CODICI KIT RAFFREDDAMENTO
TION T
COMBINATION ABLE
TABLE
PUMP MOTOR COOLING COOLING COOLING
TYPE TYPE SET SET SET
L6C L6W L8W L10W L12W SHROUD FILTER BRACKETS
(D x L) (D x L1) (D)
11 11
Z10150 D285X1000 D285X325 D285 - 2PZ
- 13
15 15 D285X1000 D285X325 D285 - 2PZ
18,5 18,5
Z10150 22 22
D285X1250 D285X325 D285 - 2PZ
- 26
Z10220
30 -
- 30
D285X1500 D285X385 D285 - 3PZ
37 37
18,5 18,5
22 22
D330X1250 D330X385 D330 - 2PZ
- 26
Z10275
30 -
- 30
D330X1500 D330X385 D330 - 3PZ
37 37
30
D330X1250 D330X385 D330 - 2PZ
37
45
52
D330X1500 D330X385 D330 - 3PZ
Z10150 55
Z10220 60
67
75 D330X1750 D330X385 D330 - 3PZ
83
93 D330X2000 D330X385 D330 - 3PZ
30
D380X1250 D380X385 D380 - 2PZ
37
45
52
D380X1500 D380X385 D380 - 3PZ
Z10275 55
Z12340 60
67
75 D380X1750 D380X385 D380 - 3PZ
83
93 D380X2000 D380X385 D380 - 3PZ
30
D420X1250 D420X385 D420 - 2PZ
37
45
52
D420X1500 D420X385 D420 - 3PZ
55
Z12420
60
67
75 D420X1750 D420X385 D420 - 3PZ
83
93 D420X2000 D420X385 D420 - 3PZ
110
D330X2000 D330X385 D330 - 3PZ
Z10150 130
150 D330X2250 D330X385 D330 - 3PZ
Z10220 110
D380X2000 D380X385 D380- 3PZ
130
Z10275
150 D380X2250 D380X385 D380 - 3PZ
110
D420X2000 D420X385 D420 - 3PZ
Z12340 130
150 D420X2250 D420X385 D420 - 3PZ
110
D450X2000 D450X385 D450 - 3PZ
Z12420 130
150 D450X2250 D450X385 D450 - 3PZ
Z10150 185 D380X2000 D380X385 D380 - 3PZ
Z10220 220 D380X2250 D380X385 D380 - 3PZ
260 D380X2250 D380X385 D380 - 3PZ
Z10220
300 D380X2500 D380X385 D380 - 3PZ
185 D420X2000 D420X385 D420 - 3PZ
220
Z10275 D420X2250 D420X385 D420 - 3PZ
260
300 D420X2500 D420X385 D420 - 3PZ
185 D450X2000 D450X385 D450 - 3PZ
220
Z12340 D450X2250 D450X385 D450 - 3PZ
260
300 D450X2500 D450X385 D450 - 3PZ
185 D480X2000 D480X385 D480 - 3PZ
220
Z12420 D480X2250 D480X385 D480 - 3PZ
260
300 D480X2500 D480X385 D480 - 3PZ
Material : Stainless steel EN 10088-1 - X5CrNi18-10 (1.4301) AISI 304. (Other materials available on request). Z10-Z12_kit-raf50-en_b_ta

93
BOOSTER SHROUD

Pressure shroud on request

Variable
DN 125÷200 DN 125÷200
PN 10÷63 PN 10÷16

Max. pressure in the pressure shroud: 16 bar

94
TECHNICAL
APPENDIX

95
SUBMERSIBLE ELECTRIC PUMP INSTALLA
INSTALLATION DIAGRAM
ALLATION

1 - Submersible electric pump.

2 - Delivery pipe.
3 - Drop cable.
4 - Control panel.
5 - Non-return valve.
6 - Gauge.
7 - On/off valve.
8 - Level sensors for protection
against dry running.
9 - Cable clamp.
10 - Electric pump
bleed/priming cap.

A - Distance between the clamps

that secure the drop cable
to the delivery pipe.
B - Distance from the bottom of
the well to the electric pump.

COMPONENTS REQUIRED FOR

CORRECT INSTALLA
INSTALLATION
ALLATION
• Control panel equipped with a main switch and thermal
relay for overload protection.
• Non-return valve at 10 meters’ distance from the delivery
ports, plus an additional non-return valve every 30÷50
meters of piping.
• Gauge and gate valve at well mouth.
• Electronic probes or floats for protection against dry
running.

RECOMMENDATIONS
RECOMMENDATIONS
• Secure the drop cable to the pipe every 2÷3 meters of
piping.
• Make sure the electric pump is installed at a safe
distance from the bottom of the well.
• Make sure there is a minimum distance of 3 mm
between the diameter of the pump and the internal
diameter of the well.
• During operation, make sure that the water circulation
speed around the motor is at least 8 cm/sec.
• Make sure that the minimum dynamic level of the water
in the well is at least 1 m above the pump’s delivery port.

TECHNICAL APPENDIX 96
EXAMPLE OF INSTALLA
INSTALLATION OF A SUBMERSIBLE ELECTRIC
ALLATION
PUMP CONTROLLED B Y AN INVERTER (HYDRO
BY VAR®)
(HYDROV

1 - Submersible electric pump.

2 - Cable clamp.
3 - Motor supply electrical cable.
4 - Level sensors for protection against
dry running.
5 - Support bracket.
6 - Check valve.
7 - Gauge.
8 - Pressure transducer.
9 - Gate valve.
10 - Diaphragm tank.
11 - QLC5 level probe control panel.
12 - QHI motor filter panel, required for
cable lenghts exceeding 20 meters.
13 - Hydrovar® (Inverter).
14 - Thermal magnetic circuit breaker (QHV).
15 - Delivery pipe.
16 - Electric pump bleed/priming cap.

N.B. For correct Inverter-Motor coupling,

contact our sales network.

97 TECHNICAL APPENDIX
MOTORI SERIE L6W - L8W - L10W - L12W
L6W - L8W - L10W - L12W MOTOR SERIES
TABLE OF POWER REDUCTION COEFFICIENTS WITH INCREASED WATER TEMPERATURE

MOTOR RATED TEMPERATURE

TYPE POWER °C

kW 25 30 35 40 45 50 55 60

STD all models 1 1 0,75 - - - - -

HT all models 1 1 1 1 1 0,85 0,75 0,65
(1) Standard winding for water temperature up to 35 °C. Lw-derating-en_a_te
(2) Special winding for water temperature from 35 °C to 60 °C.

EXAMPLE:
A 15 kW L6W motor is to be used in 35°C water.
Motor power at 35 °C = 15 x 0,75 = 11,25 kW

SELECTING CABLE CROS S-SECTIONS FOR SUBMERSIBLE

CROSS-SECTIONS
MOTORS
To select the cross-section of power cables for submersible pumps, consult the tables shown below. In these tables,
the maximum lenghts of the power cable for each cross-section are shown for each motor and next to the various
input voltage ratings.
Therefore, to find the required cable cross-section, simply read off the maximum permitted lenghts for each cross-
section next to the selected motor and required input voltage.

E.g.:
A 120 m long power cable must be matched with a 230V L4C07M235 motor.
To determine the cross-section of the cable, simply move along the row of the 230V motor until you find the maximum
lenght of 120 m or immediately above it and then read off the corresponding cross-section in that column.
In this case, between 101 and 161 metres, the second value corresponding to a 4 mm2 cable is selected.

N.B.: the tables include specific data (current and power factor) for each motor and voltage rating based on a
maximum voltage drop of 4% (HD 384.5), a maximum cable temperature of 80°C, water installation similar to air
installation at a temperature of 30°C.

TYPE OF CABLES
CABLE TYPES
THREE CORE FLAT FOUR CORE FLAT SINGLE CORE ROUND FOUR CORE ROUND
SECTION Hmin Lmin Hmax Lmax Weight Hmin Lmin Hmax Lmax Weight Dmin Dmax Weight Dmin Dmax Weight
2
mm mm mm mm mm kg/km mm mm mm mm kg/km mm mm kg/km mm mm kg/km
4 8 19,2 9 20,8 250 8 25,2 9 26,8 395 6,5 7,5 92 14 16,1 360
6 8 19,2 9 20,8 325 8 25,2 9 26,8 470 7,4 8 118 15,7 18 475
10 8 19,2 9 20,8 535 8 25,2 9 26,8 710 8,6 10 183 20,9 23,9 836
16 - - - - - - - - - - 9,6 11 251 23,8 27,1 1145
25 - - - - - - - - - - 11 13 362 28,9 32,9 1716
35 - - - - - - - - - - 12,5 14,5 497 - - -
50 - - - - - - - - - - 15 17 669 - - -
70 - - - - - - - - - - 17,5 19,5 901 - - -
95 - - - - - - - - - - 20,5 22,5 1141 - - -
120 - - - - - - - - - - 22 24,4 1435 - - -
150 - - - - - - - - - - 25,2 28,3 1795 - - -
185 - - - - - - - - - - 27,6 31 2156 - - -
240 - - - - - - - - - - 30,6 34,5 2760 - - -
L-cavi-en_a_td

TECHNICAL APPENDIX 98
L6W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR),
L6W
L6W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
DIRECT ST ART
START
Cable cross section: 4G x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm2 4 6 10 16 25 35 50 70
TYPE POWER VOLTAGE CURRENT DROP A max 42 54 75 100 127 158 192 246
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,90 9,89
L6W40T405 4 5,5 187 281 484
415 0,85 9,13
380 0,88 12,7
L6W55T405 5,5 7,5 148 222 384
415 0,82 12,5
380 0,90 17,0
L6W75T405 7,5 10 106 161 279 439
415 0,84 16,2
380 0,89 20,5
L6W93T405 9,3 12,5 87 133 233 366 561
415 0,83 19,9
380 0,90 24,2
L6W110T405 11 15 71 110 194 306 470
415 0,84 23,4
380 0,90 28,1
L6W130T405 13 17,5 60 93 165 262 403 561
415 0,85 27,0
4
380 0,88 32,1
L6W150T405 15 20 52 82 146 233 358 498
415 0,82 31,3
380 0,89 38,5
L6W185T405 18,5 25 - 65 118 190 294 410
415 0,83 37,5
380 0,87 47,3
L6W220T405 22 30 - 51 95,1 155 241 337 472
415 0,80 46,7
380 0,85 56,5
L6W260T405 26 35 - - 78 129 202 284 398
415 0,79 55,7
380 0,87 63,8
L6W300T405 30 40 - - 66 110 174 245 346 479
415 0,81 62,0
380 0,86 81,8
L6W370T405 37 50 - - - 82 132 188 267 372
415 0,80 79,4
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l6w-cavi-50-en_c_te

99 TECHNICAL APPENDIX
L6W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR),
L6W
L6W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
STAR / DEL
STAR TA ST
DELT ART
START
Cable cross section: 4G x …mm2 + 3 x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm
2
4 6 10 16 25 35 50 70
TYPE POWER VOLTAGE CURRENT DROP A max* 73 94 130 173 220 274 333 426
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,90 9,89
L6W40T405 4 5,5 327 490
415 0,85 9,13
380 0,88 12,7
L6W55T405 5,5 7,5 260 389
415 0,82 12,5
380 0,90 17,0
L6W75T405 7,5 10 189 283 488
415 0,84 16,2
380 0,89 20,5
L6W93T405 9,3 12,5 157 237 408
415 0,83 19,9
380 0,90 24,2
L6W110T405 11 15 131 197 341 535
415 0,84 23,4
380 0,90 28,1
L6W130T405 13 17,5 111 169 293 460
415 0,85 27,0
4
380 0,88 32,1
L6W150T405 15 20 99 150 261 410
415 0,82 31,3
380 0,89 38,5
L6W185T405 18,5 25 80 122 214 337 517
415 0,83 37,5
380 0,87 47,3
L6W220T405 22 30 64 99,5 176 278 426
415 0,80 46,7
380 0,85 56,5
L6W260T405 26 35 53 83 148 236 362 502
415 0,79 55,7
380 0,87 63,8
L6W300T405 30 40 44 70,2 127 203 313 436
415 0,81 62,0
380 0,86 81,8
L6W370T405 37 50 - 52 96 157 243 340 476
415 0,80 79,4
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l6w-cavi-SD-50-en_c_te

*A max is the maximum rated current of the motor

TECHNICAL APPENDIX 100

L8W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR),
L8W
L8W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
DIRECT ST ART
START
2
Cable cross section: 4G x …mm
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm2 10 16 25 35 50 70 95 120
TYPE POWER VOLTAGE CURRENT DROP A max 75 100 127 158 192 246 298 346
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,85 65,0
L8W300T405 30 40 65 110 173 244 344 475
415 0,84 59,0
380 0,87 81,0
L8W370T405 37 50 47 82 132 189 268 374 476
415 0,83 76,0
380 0,87 92,0
L8W450T405 45 60 - 69 113 163 233 327 417 516
415 0,83 88,5
380 0,86 110
L8W520T405 52 70 - - 91 133 192 271 347 430
415 0,82 104
380 0,87 118
L8W550T405 55 75 - - 82 121 176 250 321 399
415 0,83 110
4
380 0,87 124
L8W600T405 60 80 - - 77 114 166 236 305 378
415 0,83 118
380 0,88 138
L8W670T405 67 90 - - - 98 145 208 270 337
415 0,83 132
380 0,87 156
L8W750T405 75 100 - - - 84 125 182 237 296
415 0,82 148
380 0,87 172
L8W830T405 83 110 - - - - 111 162 212 266
415 0,82 163
380 0,87 192
L8W930T405 93 125 - - - - 95 142 187 236
415 0,83 180
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l8w-cavi-50-en_b_te

101 TECHNICAL APPENDIX

L8W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR),
L8W
L8W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
STAR / DEL
STAR TA ST
DELT ART
START
2 2
Cable cross section: 4G x …mm + 3 x …mm
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm
2
6 10 16 25 35 50 70 95
TYPE POWER VOLTAGE CURRENT DROP A max* 94 130 173 220 274 333 426 516
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,85 65,0
L8W300T405 30 40 70 127 203 313 435
415 0,84 59,0
380 0,87 81,0
L8W370T405 37 50 52 96 157 244 341 478
415 0,83 76,0
380 0,87 92,0
L8W450T405 45 60 44 83 136 212 298 419
415 0,83 88,5
380 0,86 110
L8W520T405 52 70 - 67 112 176 248 350 484
415 0,82 104
380 0,87 118
L8W550T405 55 75 - 60 102 161 228 323 447
415 0,83 110
4
380 0,87 124
L8W600T405 60 80 - 56 96 152 216 306 425 541
415 0,83 118
380 0,88 138
L8W670T405 67 90 - - 83 133 191 271 378 483
415 0,83 132
380 0,87 156
L8W750T405 75 100 - - 71 116 167 239 334 427
415 0,82 148
380 0,87 172
L8W830T405 83 110 - - 62,2 103 149 214 301 385
415 0,82 163
380 0,87 192
L8W930T405 93 125 - - 53 89 131 189 267 343
415 0,83 180
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l8w-cavi-SD-50-en_b_te

*A max is the maximum rated current of the motor

TECHNICAL APPENDIX 102

L10W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR
L10W
L10W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
DIRECT ST ART
START
Cable cross section: 4G x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm2 35 50 70 95 120 150 185 240
TYPE POWER VOLTAGE CURRENT DROP A max 158 192 246 298 346 399 456 538
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,87 191
L10W930T405 93 125 - 96 143 188 237 286 336 411
415 0,84 180
380 0,86 235
L10W1100T405 110 150 - - 110 147 187 228 268 329
415 0,82 220
4
380 0,86 270
L10W1300T405 130 175 - - - 124 159 194 230 283
415 0,83 255
380 0,86 308
L10W1500T405 150 200 - - - - 135 166 198 245
415 0,84 285
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l10w-cavi-50-en_b_te

L10W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR
L10W
L10W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
STAR / DEL
STAR TA ST
DELT ART
START
Cable cross section: 4G x …mm2 + 3 x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm
2
25 35 50 70 95 120 150 185
TYPE POWER VOLTAGE CURRENT DROP A max* 220 274 333 426 516 599 691 790
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,87 191
L10W930T405 93 125 90 132 191 269 345 428 511
415 0,84 180
380 0,86 235
L10W1100T405 110 150 - 102 150 215 278 345 412 480
415 0,82 220
4
380 0,86 270
L10W1300T405 130 175 - 85 127 183 238 297 356 415
415 0,83 255
380 0,86 308
L10W1500T405 150 200 - - 107 157 205 257 310 362
415 0,84 285
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l10w-cavi-SD-50-en_b_te

*A max is the maximum rated current of the motor

103 TECHNICAL APPENDIX

L12W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR
L12W
L12W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
DIRECT ST ART
START
Cable cross section: 4G x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm2 50 70 95 120 150 185 240 300
TYPE POWER VOLTAGE CURRENT DROP A max 192 246 298 346 399 456 538 621
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,87 380
L12W1850T405 185 250 - - - - 127 154 194 229
415 0,86 360
380 0,86 470
L12W2200T405 220 300 - - - - - - 150 179
415 0,83 435
4
380 0,87 525
L12W2600T405 260 350 - - - - - - 131 158
415 0,83 498
380 0,87 620
L12W3000T405 300 400 - - - - - - - 128
415 0,84 570
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l12w-cavi-50-en_b_te

L12W TRIFASE, 50 Hz: DIMENSIONAMENTO CAVI PER ACQUA POTABILE DRINCABLE - WRAS 07 (EPR
L12W
L12W,, 50 Hz: SIZING OF ETHYLENE-PROPILENE (EPR) CABLES
STAR / DEL
STAR TA ST
DELT ART
START
Cable cross section: 4G x …mm2 + 3 x …mm2
MOTOR RATED RATED Cos ϕ RATED VOLTAGE mm
2
50 70 95 120 150 185 240 300
TYPE POWER VOLTAGE CURRENT DROP A max* 333 426 516 599 691 790 932 1076
THREE-PHASE Kw HP V A % Maximum lenght in metres
380 0,87 380
L12W1850T405 185 250 - 120 160 203 246 289 355 413
415 0,86 360
380 0,86 470
L12W2200T405 220 300 - - 123 158 193 229 282 329
415 0,83 435
4
380 0,87 525
L12W2600T405 260 350 - - - 137 169 202 251 294
415 0,83 498
380 0,87 620
L12W3000T405 300 400 - - - - 138 166 208 245
415 0,84 570
Exposed cable laid at a temperature of 30°C, maximum conductor temperature of 90°C l12w-cavi-SD-50-en_b_te

*A max is the maximum rated current of the motor

TECHNICAL APPENDIX 104

SPLICE BETWEEN DROP CABLE AND MOTOR CABLE
GIUNZIONE TRA CAVO DI DISCESA E CAVO MOTORE

2
MOTOR FOUR-CORE DROP CABLE - SECTION (mm )
POWER kW TYPE OF SPLICE
TYPE
1,5 2,5 4 6 10 16 25 35 50 70 95 120 150 185 240 300

Resin-filled method GR1 GR1 GR1 GR2 GR2 GR6 GR6 GR6 GR4 GR5 GR5 - - - - -

4OS
0,37 - 7,5 Heat-shrink method GT1 GT1 GT2 GT2 GT3 GT4 GT5 GT6 - - - - - - - -
L4C

Tape method Self-vulcanizing tape + self-vulcanizing sealing putty and PVC tape (1)

Resin-filled method - - GR1 GR2 GR2 GR6 GR6 GR6 GR4 GR5 GR5 - - - - -

L6C
4 - 37 Heat-shrink method - - GT2 GT2 GT3 GT4 GT5 GT6 - - - - - - - -
L6W

Tape method Self-vulcanizing tape + self-vulcanizing sealing putty and PVC tape (1)

MOTOR THREE-CORE DROP CABLE - SECTION (mm2)

POWER kW TYPE OF SPLICE
TYPE
1,5 2,5 4 6 10 16 25 35 50 70 95 120 150 185 240 300

Resin-filled method - - GR1 GR1 GR2 GR2 GR6 GR6 GR6 GR4 GR5 - - - - -

L6C
4 - 37 Heat-shrink method - - GT2 GT2 GT3 GT4 GT5 GT6 - - - - - - - -
L6W

Tape method Self-vulcanizing tape + PVC tape

MOTOR SINGLE-CORE DROP CABLE - SECTION (mm2)

POWER kW TYPE OF SPLICE
TYPE
1,5 2,5 4 6 10 16 25 35 50 70 95 120 150 185 240 300

Resin-filled method - - - GR1 GR1 GR1 GR1 GR1 GR1 GR2 GR2 GR2 GR6 GR6 GR6 GR4
L8W
L10W 30 - 300 Heat-shrink method - - - - - - - - - - - - - - - -
L12W
Tape method Self-vulcanizing tape + PVC tape

(1) Use self-vulcanizing sealing putty to fill in the gaps between the three-conductor cable and the ground cable in the area covered

by the final layer of tape, to restore continuity to the protective sheath.

RESIN-FILLED SPLICES HEAT-SHRINK SPLICES

TYPE L [mm] TYPE L [mm] TYPE L [mm] TYPE L [mm]
GR1 148 x 32 GR5 369 x 76 GT1 450 GT4 450
GR2 178 x 36 GR6 270 x 55 GT2 450 GT5 500
GR4 319 x 63 GT3 450 GT6 500
L-giunzioni-en_d_te

105 TECHNICAL APPENDIX

CALCULATING THE SPEED OF THE FL
CALCULATING UID THA
FLUID T FL
THAT OWS
FLOWS
AROUND A SUBMERGED MOTOR AND SIZING OF THE
COOLING SLEEVE

The following formula is used to verify whether the speed of the fluid that flows around the motor of a submersible pump is high
enough to guarantee the proper cooling of the motor:
Q
v= 2
2
D2 d
π ⋅( − )
4 4
Where: Q in [m3/s] is the operating flow rate of the electric pump; only half of this flow is taken into account, because the fluid
which is sucked into the area of the filter (2), comes from the motor side (3) as well as from the pump side (1);
D in [m] corresponds to the diameter of the well;
d in [m] corresponds to the diameter of the motor (3);
v in [m/s] is the calculated speed of the fluid that flows around the motor.
Now, compare the speed thus calculated (v) with the minimum speed required for correct cooling of the motor (vm): if v ≥ vm it
means that the motor is properly cooled, if v < vm will be necessary to mount a cooling sleeve (4).
Example
Example:
An electric pump OZ630/12 (motor diameter d = 0.144 m) operates in an 8" well (well diameter D = 0.203 m) with flow rate
Q = 20 m3/h = 0.0055 m3/s.
Speed of fluid v = (0.0055/2) / {π·[(0.203)2/4 – (0.144)2/4]} = 0.17 m/s.
The minimum speed required for proper motor cooling is vm = 0.20 m/s.
Because v < vm, it will be necessary to mount a cooling sleeve.

The following formula is used to determine the maximum diameter of a cooling sleeve to be mounted on a submersible motor:

⎛ Q d2 ⎞
D = 4 ⋅ ⎜⎜ + ⎟
⎝ v ⋅π 4 ⎟⎠
Where: Q in [m3/s] is the operating flow rate of the electric pump; the entire flow is taken into account because the fluid comes
from the motor side (3) only;
D in [m] corresponds to the diameter of the cooling sleeve (4);
d in [m] corresponds to the diameter of the motors(3);
vm in [m/s] is the minimum speed of the fluid that flows around the motor.
If the electric pump operates at different flow rate, the minimum flow rate must be taken into account for calculating the diameter
of the cooling sleeve.
Example
Example:
A motor coupled to the electric pump OZ615/24 (motor diameter d = 0.144 m), which operates with flow rate
Q = 15 m3/h = 0.0042 m3/s, requires a minimum speed of the fluid of vm = 0.20 m/s.
Cooling sleeve diameter D = {4·[(0.0042/(0.2·π)+(0.144)2/4] }0.5 = 0.217 m.

TECHNICAL APPENDIX 106

ASYNCHRONOUS MOTOR STARTING SYSTEMS
STARTING

Direct Autotransformer
Suitable for low-power motors.
The pump is started with a voltage which is lower than
The starting current (Is) is much higher than the rated
the rated one.
current (In).
The Lowara panels use an autotransformer with a voltage
Starting current Is = In x 4 ÷ 8
that is 70% the value of the line voltage.
Starting torque Ts = Tn x 2 ÷ 3
The switch to the rated voltage occurs without any
interruptions of the power supply.
Indirect Rated voltage Un = 400 V
• Star/Delta
The starting current (Is) is three times less than the direct
starting current. Starting current
Starting current Is = In x 1.3 ÷ 2.7 Us
Starting torque Ts = Tn x 0.7 ÷ 1
In the star to delta changeover phase (approx. 70 ms) the
motor is not supplied and tends to reduce its rotation Starting torque
Is = In x 4÷8 x
( ) Un
= In x 3÷6

speed. Us

( )
2

In the case of submersible electric pumps with power Ts = Tn x 2÷3 x = Tn x 1÷1,5

above 10 HP, the modest mass of the rotor causes a Un
slowdown at changeover, so that the initial Star supply
phase is rendered partially useless.
In such cases we recommend using impedance panels or
an autotransformer.
DIAGRAM OF STARTING INPUTS

• Impedances Ia

The motor is started with a voltage which is lower than

the rated one, and which is obtained by means of
impedances.
The Lowara panels use impedances which cut down to
70% the starting voltage.
The switch to the rated voltage takes place without any
interruptions of the power supply.

Rated voltage Un = 400 V

Starting voltage Us = Un x 0,7 = 280 V

Starting current

( )
Us
Is = In x 4÷8 x = In x 3÷6
Un
1 = Direct SPEED’
2 = Star-Delta
Starting torque 3 = Impedances
4 = Autotransformer

( )
Us 2

Ts = Tn x 2÷3 x = Tn x 1÷1,5
Un

107 TECHNICAL APPENDIX

WATER REQUIREMENTS IN CIVIL USERS
Determination of the water requirement depends on the type of users and contemporaneity factor. The calculation
may be subject to regulations, standards or customs that may vary from country to country. The calculation method
shown below is an example based on practical experience, designed to provide a reference value and not a substi-
tute for detailed analytical calculation.

Water requirements in condominiums

The consumption table shows the maximum values for each delivery point, depending on the plumbing amenities.

MAXIMUM CONSUMPTION FOR EACH DELIVERY POINT

TYPE CONSUMPTION (l/min)
Sink 9
Dishwasher 10
Washing machine 12
Shower 12
Bathtub 15
Washbasin 6
Bidet 6
Flush tank WC 6
Controlled flushing system WC 90
G-at-cm_a_th

The sum of the water consumption values of each delivery point determines the maximum theoretical re-
quirement, which must be reduced according to the contemporaneity coefficient, because in actual fact the
delivery points are never used all together.

1
f = Coefficient for apartments with one bathroom and flush tank WC
(0,857 x Nr x Na)
1
f = Coefficient for apartments with one bathroom and controlled flushing system WC
(0,857 x Nr x Na)
1,03
f = Coefficient for apartments with two bathrooms and flush tank WC
(0,545 x Nr x Na )
0,8
f = Coefficient for apartments with two bathrooms and controlled flushing system WC
(0,727 x Nr x Na )
f= coefficient; Nr= number of delivery points; Na= number of apartments

The table of water requirements in civil users shows the maximum contemporaneity flow-rate values
based on the number of apartments and the type of WC for apartments with one bathroom and two bath-
rooms. As regards apartments with one bathroom, 7 drawing points have been taken into consideration, while 11
points have been considered for apartments with two bathrooms. If the number of drawing points or apartments is
different, use the formulas to calculate the requirement.

TECHNICAL APPENDIX 108

TABLE OF WATER REQUIREMENTS IN CIVIL USERS

NUMBER OF WITH FLUSH TANK WC WITH CONTROLLED FLUSHING SYSTEM WC

APARTMENTS 1 2 1 2
FLOW RATE (l/min)
1 32 40 60 79
2 45 56 85 111
3 55 68 105 136
4 63 79 121 157
5 71 88 135 176
6 78 97 148 193
7 84 105 160 208
8 90 112 171 223
9 95 119 181 236
10 100 125 191 249
11 105 131 200 261
12 110 137 209 273
13 114 143 218 284
14 119 148 226 295
15 123 153 234 305
16 127 158 242 315
17 131 163 249 325
18 134 168 256 334
19 138 172 263 343
20 142 177 270 352
21 145 181 277 361
22 149 185 283 369
23 152 190 290 378
24 155 194 296 386
25 158 198 302 394
26 162 202 308 401
27 165 205 314 409
28 168 209 320 417
29 171 213 325 424
30 174 217 331 431
35 187 234 357 466
40 200 250 382 498
45 213 265 405 528
50 224 280 427 557
55 235 293 448 584
60 245 306 468 610
65 255 319 487 635
70 265 331 506 659
75 274 342 523 682
80 283 354 540 704
85 292 364 557 726
90 301 375 573 747
95 309 385 589 767
100 317 395 604 787
120 347 433 662 863
140 375 468 715 932
160 401 500 764 996
180 425 530 811 1056
200 448 559 854 1114
For seaside resorts, a flow rate increased by at least 20% must be considered. G-at-fi_a_th

109 TECHNICAL APPENDIX

WATER REQUIREMENTS FOR COMMUNITY BUILDINGS
The requirements of buildings intended for specific uses, such as offices, residential units, hotels, de-
partment stores, nursing homes and so on, are different from those of condominiums, and both their
global daily water consumption and the maximum contemporaneity flow rate are usually greater. The diagram
of water requirements for community buildings shows the maximum contemporaneity flow rate of
some types of communities, for guidance.
These requirements must be determined case by case with the utmost accuracy, using analytical calculation meth-
ods, according to particular needs and local provisions.

For seaside resorts, the flow rate must be increased by at least 20%.

1= Offices (N. of people)

2= Department stores (N. of people)
3= Nursing homes (N. of beds)
4= Hotels, residences (N. of beds)

TECHNICAL APPENDIX 110

NPSH

The minimum operating values that can be reached at the The maximum possible suction head for installation
pump suction end are limited by the onset of cavitation. depends on the value of the atmospheric pressure
(i.e. the elevation above sea level at which the pump
Cavitation is the formation of vapour-filled cavities within is installed) and the temperature of the liquid.
liquids where the pressure is locally reduced to a critical value,
or where the local pressure is equal to, or just below the To help the user, with reference to water temperature
vapour pressure of the liquid. (4° C) and to the elevation above sea level, the
following tables show the drop in hydraulic pressure
The vapour-filled cavities flow with the current and head in relation to the elevation above sea level, and
when they reach a higher pressure area the vapour the suction loss in relation to temperature.
contained in the cavities condenses. The cavities collide,
generating pressure waves that are transmitted to the Water
walls. These, being subjected to stress cycles, gradually temperature (°C) 20 40 60 80 90 110 120
become deformed and yield due to fatigue. This Suction
phenomenon, characterized by a metallic noise loss (m) 0,2 0,7 2,0 5,0 7,4 15,4 21,5
produced by the hammering on the pipe walls, is called
incipient cavitation.
Elevation above
sea level (m) 500 1000 1500 2000 2500 3000
The damage caused by cavitation may be magnified by
electrochemical corrosion and a local rise in Suction
temperature due to the plastic deformation of the loss (m) 0,55 1,1 1,65 2,2 2,75 3,3
walls. The materials that offer the highest resistance to
heat and corrosion are alloy steels, especially austenitic
steel. The conditions that trigger cavitation may be Friction loss is shown in the tables at pages 113-114 of
assessed by calculating the total net suction head, this catalogue. To reduce it to a minimum, especially
referred to in technical literature with the acronym in cases of high suction head (over 4-5 m.) or within
NPSH (Net Positive Suction Head). the operating limits with high flow rates, we
recommend using a suction line having a larger
The NPSH represents the total energy (expressed in m.) diameter than that of the pump’s suction port.
of the liquid measured at suction under conditions of It is always a good idea to position the pump as close
incipient cavitation, excluding the vapour pressure as possible to the liquid to be pumped.
(expressed in m.) that the liquid has at the pump inlet.
Make the following calculation:
To find the static height hz at which to install the
machine under safe conditions, the following formula Liquid: water at ~15°C γ = 1 kg/dm3
must be verified: Flow rate required: 30 m3/h
Head for required delivery: 43 m.
Suction lift: 3,5 m.
hp + hz ≥ (NPSHr + 0.5) + hf + hpv 1 The selection is an FHE 40-200/75 pump whose NPSH
required value is, at 30 m3/h, di 2,5 m.
where:
hp is the absolute pressure applied to the free liquid For water at 15 °C
surface in the suction tank, expressed in m. of
liquid; hp is the quotient between the barometric hp = Pa / γ = 10,33m, hpv = Pv / γ = 0,174m (0,01701 bar)
pressure and the specific weight of the liquid.
The Hf flow resistance in the suction line with foot
hz is the suction lift between the pump axis and the
valves is ~ 1,2 m.
free liquid surface in the suction tank, expressed
By substituting the parameters in formula 1 with the
in m.; hz is negative when the liquid level is
numeric values above, we have:
lower than the pump axis.
hf is the flow resistance in the suction line and its
10,33 + (-3,5) ≥ (2,5 + 0,5) + 1,2 + 0,17
accessories, such as: fittings, foot valve, gate
valve, elbows, etc. from which we have: 6,8 > 4,4
hpv is the vapour pressure of the liquid at the
operating temperature, expressed in m. of The relation is therefore verified.
liquid. hpv is the quotient between the Pv vapour
pressure and the liquid’s specific weight.
0,5 is the safety factor.

111 TECHNICAL APPENDIX

TECHNICAL APPENDIX VAPOUR PRESSURE PS VAPOUR
PRESSURE AND ρ DENSITY OF WATER TABLE

t T ps ρ t T ps ρ t T ps ρ
°C K bar kg/dm3 °C K bar kg/dm3 °C K bar kg/dm3
0 273,15 0,00611 0,9998 55 328,15 0,15741 0,9857 120 393,15 1,9854 0,9429
1 274,15 0,00657 0,9999 56 329,15 0,16511 0,9852 122 395,15 2,1145 0,9412
2 275,15 0,00706 0,9999 57 330,15 0,17313 0,9846 124 397,15 2,2504 0,9396
3 276,15 0,00758 0,9999 58 331,15 0,18147 0,9842 126 399,15 2,3933 0,9379
4 277,15 0,00813 1,0000 59 332,15 0,19016 0,9837 128 401,15 2,5435 0,9362
5 278,15 0,00872 1,0000 60 333,15 0,1992 0,9832 130 403,15 2,7013 0,9346
6 279,15 0,00935 1,0000 61 334,15 0,2086 0,9826 132 405,15 2,867 0,9328
7 280,15 0,01001 0,9999 62 335,15 0,2184 0,9821 134 407,15 3,041 0,9311
8 281,15 0,01072 0,9999 63 336,15 0,2286 0,9816 136 409,15 3,223 0,9294
9 282,15 0,01147 0,9998 64 337,15 0,2391 0,9811 138 411,15 3,414 0,9276
10 283,15 0,01227 0,9997 65 338,15 0,2501 0,9805 140 413,15 3,614 0,9258
11 284,15 0,01312 0,9997 66 339,15 0,2615 0,9799 145 418,15 4,155 0,9214
12 285,15 0,01401 0,9996 67 340,15 0,2733 0,9793 155 428,15 5,433 0,9121
13 286,15 0,01497 0,9994 68 341,15 0,2856 0,9788 160 433,15 6,181 0,9073
14 287,15 0,01597 0,9993 69 342,15 0,2984 0,9782 165 438,15 7,008 0,9024
15 288,15 0,01704 0,9992 70 343,15 0,3116 0,9777 170 433,15 7,920 0,8973
16 289,15 0,01817 0,9990 71 344,15 0,3253 0,9770 175 448,15 8,924 0,8921
17 290,15 0,01936 0,9988 72 345,15 0,3396 0,9765 180 453,15 10,027 0,8869
18 291,15 0,02062 0,9987 73 346,15 0,3543 0,9760 185 458,15 11,233 0,8815
19 292,15 0,02196 0,9985 74 347,15 0,3696 0,9753 190 463,15 12,551 0,8760
20 293,15 0,02337 0,9983 75 348,15 0,3855 0,9748 195 468,15 13,987 0,8704
21 294,15 0,24850 0,9981 76 349,15 0,4019 0,9741 200 473,15 15,550 0,8647
22 295,15 0,02642 0,9978 77 350,15 0,4189 0,9735 205 478,15 17,243 0,8588
23 296,15 0,02808 0,9976 78 351,15 0,4365 0,9729 210 483,15 19,077 0,8528
24 297,15 0,02982 0,9974 79 352,15 0,4547 0,9723 215 488,15 21,060 0,8467
25 298,15 0,03166 0,9971 80 353,15 0,4736 0,9716 220 493,15 23,198 0,8403
26 299,15 0,03360 0,9968 81 354,15 0,4931 0,9710 225 498,15 25,501 0,8339
27 300,15 0,03564 0,9966 82 355,15 0,5133 0,9704 230 503,15 27,976 0,8273
28 301,15 0,03778 0,9963 83 356,15 0,5342 0,9697 235 508,15 30,632 0,8205
29 302,15 0,04004 0,9960 84 357,15 0,5557 0,9691 240 513,15 33,478 0,8136
30 303,15 0,04241 0,9957 85 358,15 0,5780 0,9684 245 518,15 36,523 0,8065
31 304,15 0,04491 0,9954 86 359,15 0,6011 0,9678 250 523,15 39,776 0,7992
32 305,15 0,04753 0,9951 87 360,15 0,6249 0,9671 255 528,15 43,246 0,7916
33 306,15 0,05029 0,9947 88 361,15 0,6495 0,9665 260 533,15 46,943 0,7839
34 307,15 0,05318 0,9944 89 362,15 0,6749 0,9658 265 538,15 50,877 0,7759
35 308,15 0,05622 0,9940 90 363,15 0,7011 0,9652 270 543,15 55,058 0,7678
36 309,15 0,05940 0,9937 91 364,15 0,7281 0,9644 275 548,15 59,496 0,7593
37 310,15 0,06274 0,9933 92 365,15 0,7561 0,9638 280 553,15 64,202 0,7505
38 311,15 0,06624 0,9930 93 366,15 0,7849 0,9630 285 558,15 69,186 0,7415
39 312,15 0,06991 0,9927 94 367,15 0,8146 0,9624 290 563,15 74,461 0,7321
40 313,15 0,07375 0,9923 95 368,15 0,8453 0,9616 295 568,15 80,037 0,7223
41 314,15 0,07777 0,9919 96 369,15 0,8769 0,9610 300 573,15 85,927 0,7122
42 315,15 0,08198 0,9915 97 370,15 0,9094 0,9602 305 578,15 92,144 0,7017
43 316,15 0,09639 0,9911 98 371,15 0,9430 0,9596 310 583,15 98,70 0,6906
44 317,15 0,09100 0,9907 99 372,15 0,9776 0,9586 315 588,15 105,61 0,6791
45 318,15 0,09582 0,9902 100 373,15 1,0133 0,9581 320 593,15 112,89 0,6669
46 319,15 0,10086 0,9898 102 375,15 1,0878 0,9567 325 598,15 120,56 0,6541
47 320,15 0,10612 0,9894 104 377,15 1,1668 0,9552 330 603,15 128,63 0,6404
48 321,15 0,11162 0,9889 106 379,15 1,2504 0,9537 340 613,15 146,05 0,6102
49 322,15 0,11736 0,9884 108 381,15 1,3390 0,9522 350 623,15 165,35 0,5743
50 323,15 0,12335 0,9880 110 383,15 1,4327 0,9507 360 633,15 186,75 0,5275
51 324,15 0,12961 0,9876 112 385,15 1,5316 0,9491 370 643,15 210,54 0,4518
52 325,15 0,13613 0,9871 114 387,15 1,6362 0,9476 374,15 647,30 221,20 0,3154
53 326,15 0,14293 0,9862 116 389,15 1,7465 0,9460
54 327,15 0,15002 0,9862 118 391,15 1,8628 0,9445
G-at_npsh_a_sc

TECHNICAL APPENDIX 112

TABLE OF FLOW RESISTANCE IN 100 m OF STRAIGHT CAST
IRON PIPELINE (HAZEN-WILLIAMS FORMULA C=100)

FLOW RATE NOMINAL DIAMETER in mm and INCHES

m3/h l/min 15 20 25 32 40 50 65 80 100 125 150 175 200 250 300 350 400
1/2" 3/4" 1" 1 1/4" 1 1/2" 2 2 1/2" 3" 4" 5" 6" 7" 8" 10" 12" 14" 16"
v 0,94 0,53 0,34 0,21 0,13
0,6 10 hr 16 3,94 1,33 0,40 0,13 The hr values must be multiplied by:
v 1,42 0,80 0,51 0,31 0,20 0.71 for galvanized or painted steel pipes
0,9 15 hr 33,9 8,35 2,82 0,85 0,29 0.54 for stainless steel or copper pipes
v 1,89 1,06 0,68 0,41 0,27 0,17 0.47 for PVC or PE pipes
1,2 20 hr 57,7 14,21 4,79 1,44 0,49 0,16
v 2,36 1,33 0,85 0,52 0,33 0,21
1,5 25 hr 87,2 21,5 7,24 2,18 0,73 0,25
v 2,83 1,59 1,02 0,62 0,40 0,25
1,8 30 hr 122 30,1 10,1 3,05 1,03 0,35
v 3,30 1,86 1,19 0,73 0,46 0,30
2,1 35 hr 162 40,0 13,5 4,06 1,37 0,46
v 2,12 1,36 0,83 0,53 0,34 0,20
2,4 40 hr 51,2 17,3 5,19 1,75 0,59 0,16
v 2,65 1,70 1,04 0,66 0,42 0,25
3 50 hr 77,4 26,1 7,85 2,65 0,89 0,25
v 3,18 2,04 1,24 0,80 0,51 0,30
3,6 60 hr 108 36,6 11,0 3,71 1,25 0,35
v 3,72 2,38 1,45 0,93 0,59 0,35
4,2 70 hr 144 48,7 14,6 4,93 1,66 0,46
v 4,25 2,72 1,66 1,06 0,68 0,40
4,8 80 hr 185 62,3 18,7 6,32 2,13 0,59
v 3,06 1,87 1,19 0,76 0,45 0,30
5,4 90 hr 77,5 23,3 7,85 2,65 0,74 0,27
v 3,40 2,07 1,33 0,85 0,50 0,33
6 100 hr 94,1 28,3 9,54 3,22 0,90 0,33
v 4,25 2,59 1,66 1,06 0,63 0,41
7,5 125 hr 142 42,8 14,4 4,86 1,36 0,49
v 3,11 1,99 1,27 0,75 0,50 0,32
9 150 hr 59,9 20,2 6,82 1,90 0,69 0,23
v 3,63 2,32 1,49 0,88 0,58 0,37
10,5 175 hr 79,7 26,9 9,07 2,53 0,92 0,31
v 4,15 2,65 1,70 1,01 0,66 0,42
12 200 hr 102 34,4 11,6 3,23 1,18 0,40
v 5,18 3,32 2,12 1,26 0,83 0,53 0,34
15 250 hr 154 52,0 17,5 4,89 1,78 0,60 0,20
v 3,98 2,55 1,51 1,00 0,64 0,41
18 300 hr 72,8 24,6 6,85 2,49 0,84 0,28
v 5,31 3,40 2,01 1,33 0,85 0,54 0,38
24 400 hr 124 41,8 11,66 4,24 1,43 0,48 0,20
v 6,63 4,25 2,51 1,66 1,06 0,68 0,47
30 500 hr 187 63,2 17,6 6,41 2,16 0,73 0,30
v 5,10 3,02 1,99 1,27 0,82 0,57 0,42
36 600 hr 88,6 24,7 8,98 3,03 1,02 0,42 0,20
v 5,94 3,52 2,32 1,49 0,95 0,66 0,49
42 700 hr 118 32,8 11,9 4,03 1,36 0,56 0,26
v 6,79 4,02 2,65 1,70 1,09 0,75 0,55
48 800 hr 151 42,0 15,3 5,16 1,74 0,72 0,34
v 7,64 4,52 2,99 1,91 1,22 0,85 0,62
54 900 hr 188 52,3 19,0 6,41 2,16 0,89 0,42
v 5,03 3,32 2,12 1,36 0,94 0,69 0,53
60 1000 hr 63,5 23,1 7,79 2,63 1,08 0,51 0,27
v 6,28 4,15 2,65 1,70 1,18 0,87 0,66
75 1250 hr 96,0 34,9 11,8 3,97 1,63 0,77 0,40
v 7,54 4,98 3,18 2,04 1,42 1,04 0,80
90 1500 hr 134 48,9 16,5 5,57 2,29 1,08 0,56
v 8,79 5,81 3,72 2,38 1,65 1,21 0,93
105 1750 hr 179 65,1 21,9 7,40 3,05 1,44 0,75
v 6,63 4,25 2,72 1,89 1,39 1,06 0,68
120 2000 hr 83,3 28,1 9,48 3,90 1,84 0,96 0,32
v 8,29 5,31 3,40 2,36 1,73 1,33 0,85
150 2500 hr 126 42,5 14,3 5,89 2,78 1,45 0,49
v 6,37 4,08 2,83 2,08 1,59 1,02 0,71
180 3000 hr 59,5 20,1 8,26 3,90 2,03 0,69 0,28
v 7,43 4,76 3,30 2,43 1,86 1,19 0,83
210 3500 hr 79,1 26,7 11,0 5,18 2,71 0,91 0,38
v 8,49 5,44 3,77 2,77 2,12 1,36 0,94
240 4000 hr 101 34,2 14,1 6,64 3,46 1,17 0,48
v 6,79 4,72 3,47 2,65 1,70 1,18
300 5000 hr 51,6 21,2 10,0 5,23 1,77 0,73
v 8,15 5,66 4,16 3,18 2,04 1,42
360 6000 hr 72,3 29,8 14,1 7,33 2,47 1,02
v 6,61 4,85 3,72 2,38 1,65 1,21
420 7000 hr 39,6 18,7 9,75 3,29 1,35 0,64
v 7,55 5,55 4,25 2,72 1,89 1,39
480 8000 hr 50,7 23,9 12,49 4,21 1,73 0,82
v 8,49 6,24 4,78 3,06 2,12 1,56 1,19
540 9000 hr 63,0 29,8 15,5 5,24 2,16 1,02 0,53
v 6,93 5,31 3,40 2,36 1,73 1,33
600 10000 hr 36,2 18,9 6,36 2,62 1,24 0,65
G-at-pct_a_th
hr = flow resistance for 100m of straight pipeline (m)
V = water speed (m/s)

113 TECHNICAL APPENDIX

FLOW RESISTANCE

TABLE OF FLOW RESISTANCE IN BENDS, VALVES AND GATES

The flow resistance is calculated using the equivalent pipeline length method according to the table below:

ACCESSORY DN
TYPE 25 32 40 50 65 80 100 125 150 200 250 300
Equivalent pipeline length (m)
45° bend 0,2 0,2 0,4 0,4 0,6 0,6 0,9 1,1 1,5 1,9 2,4 2,8
90° bend 0,4 0,6 0,9 1,1 1,3 1,5 2,1 2,6 3,0 3,9 4,7 5,8
90° smooth bend 0,4 0,4 0,4 0,6 0,9 1,1 1,3 1,7 1,9 2,8 3,4 3,9
Union tee or cross 1,1 1,3 1,7 2,1 2,6 3,2 4,3 5,3 6,4 7,5 10,7 12,8
Gate - - - 0,2 0,2 0,2 0,4 0,4 0,6 0,9 1,1 1,3
Non return valve 1,1 1,5 1,9 2,4 3,0 3,4 4,7 5,9 7,4 9,6 11,8 13,9
G-a-pcv_a_th

The table is valid for the Hazen Williams coefficient C = 100 (cast iron pipework). For steel pipework, multiply the
values by 1.41. For stainless steel, copper and coated cast iron pipework, multiply the values by 1.85.
When the equivalent pipeline length has been determined, the flow resistance is obtained from the table of
flow resistance.
The values given are guideline values which are bound to vary slightly according to the model, especially for gate
valves and non-return valves, for which it is a good idea to check the values supplied by the manufacturers.

TECHNICAL APPENDIX 114

VOL UMETRIC
OLUMETRIC
VOLUMETRIC CAP ACITY
CAPACITY
CAPACITY
Litres Cubic metres Cubic feet Cubic feet Imp. gal. US gal.
per minute per hour per hour per minute per minute per minute
l/min m3/h ft3/h ft3/min Imp. gal/min Us gal./min
1,0000 0,0600 2,1189 0,0353 0,2200 0,2642
16,6667 1,0000 35,3147 0,5886 3,6662 4,4029
0,4719 0,0283 1,0000 0,0167 0,1038 0,1247
28,3168 1,6990 60,0000 1,0000 6,2288 7,4805
4,5461 0,2728 9,6326 0,1605 1,0000 1,2009
3,7854 0,2271 8,0208 0,1337 0,8327 1,0000

PRESSURE
SURE
PRESSURE
PRES AND HEAD
AND HEAD
Newton per kilo Pascal bar Pound force per metre millimetre of
square metre square inch of water mercury
N/m2 kPa bar psi m H 2O mm Hg
1,0000 0,0010 1 x 10-5 1.45 x 10-4 1.02 x 10-4 0,0075
1000,0000 1,0000 0,0100 0,1450 0,1020 7,5006
1 x 105 100,0000 1,0000 14,5038 10,1972 750,0638
6894,7570 6,8948 0,0689 1,0000 0,7031 51,7151
9806,6500 9,8067 0,0981 1,4223 1,0000 73,5561
133,3220 0,1333 0,0013 0,0193 0,0136 1,0000

LENGTH
TH
LENGTH
LENG
millimetre centimetre metre inch foot yard
mm cm m in ft yd

1,0000 0,1000 0,0010 0,0394 0,0033 0,0011

10,0000 1,0000 0,0100 0,3937 0,0328 0,0109
1000,0000 100,0000 1,0000 39,3701 3,2808 1,0936
25,4000 2,5400 0,0254 1,0000 0,0833 0,0278
304,8000 30,4800 0,3048 12,0000 1,0000 0,3333
914,4000 91,4400 0,9144 36,0000 3,0000 1,0000

VOLUME
V OLUME
OLUME
cubic metre litre millilitre imp. Gallon US gallon cubic foot
3
m litro ml imp. gal. US gal. ft3

1,0000 1000,0000 1 x 106 219,9694 264,1720 35,3147

0,0010 1,0000 1000,0000 0,2200 0,2642 0,0353
1 x 10-6 0,0010 1,0000 2.2 x 10-4 2.642 x 10-4 3.53 x 10-5
0,0045 4,5461 4546,0870 1,0000 1,2009 0,1605
0,0038 3,7854 3785,4120 0,8327 1,0000 0,1337
0,0283 28,3168 28316,8466 6,2288 7,4805 1,0000
G-at_pp-en_a_sc

115 TECHNICAL APPENDIX

FURTHER PRODUCT SELECTION AND DOCUMENTATION
DOCUMENTA

Xylect

Xylect is pump solution selection software with an extensive online database of product information across the entire
Lowara, and Vogel range of pumps and related products, with multiple search options and helpful project management
facilities. The system holds up-to-date product information on thousands of products and accessories.
The possibility to search by applications and the detailed information output given makes it easy to make the optimal
selection without having detailed knowledge about the Lowara and Vogel products.

The search can be made by:

• Application
• Product type
• Duty point

Xylect gives a detailed output:

• List with search results
• Performance curves (flow, head, power,
efficiency, NPSH)
• Motor data
• Dimensional drawings
• Options
• Data sheet printouts
The search by application guides users not familiar with
• Document downloads incl dxf files the product range to the right choice.

TECHNICAL APPENDIX 116

FURTHER PRODUCT SELECTION AND DOCUMENTATION
DOCUMENTA

Xylect

The detailed output makes it easy to select the optimal pump from the given alternatives.

The best way to work with Xylect is to create a

personal account. This makes it possible to:

• Set own standard units

• Create and save projects

• Share projects with other Xylect users

Every user have a My Xylect space, where all projects

are saved.

For more information about Xylect please contact Dimensional drawings appear on the screen and can be
our sales network or visit www.xylect.com. downloaded in dxf format.

117 TECHNICAL APPENDIX

118
Xylem
1) The tissue in plants that brings water upward from the roots;
2) a leading global water technology company.

We’re 12,000 people unified in a common purpose: creating innovative solutions

to meet our world’s water needs. Developing new technologies that will improve
the way water is used, conserved, and re-used in the future is central to our work.
We move, treat, analyze, and return water to the environment, and we help people
use water efficiently, in their homes, buildings, factories and farms. In more than 150
countries, we have strong, long-standing relationships with customers who know us
for our powerful combination of leading product brands and applications expertise,
backed by a legacy of innovation.

For more information on how Xylem can help you, go to xyleminc.com.

Headquarters
LOWARA S.r.l. Unipersonale
Via Vittorio Lombardi 14
36075 Montecchio Maggiore - Vicenza - Italy
Tel.(+39) 0444 707111 - Fax(+39) 0444 492166
e-mail: [email protected]
web: www.lowara.com - www.completewatersystems.com
LOWARA reserves the right to make modification without prior notice.
LOWARA is a trademark of Xylem Inc. or one of its subsidiaries.