Scribd
Upload
28 views5 pages

Pot Tach

Uploaded by

Mohammad alhaboob2030
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
28 views5 pages

Pot Tach

Uploaded by

Mohammad alhaboob2030
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

ME 3200 Mechatronics I Laboratory

Lab 8: Angular Position and Velocity Sensors

In this exercise you will explore the use of the potentiometer and the tachometer as
angular position and velocity sensors. In addition, you will have the opportunity to
implement the skills gained in the experiment on operational amplifiers.

Potentiometers
In previous exercises you have used the bench potentiometer to create a controllable
voltage supply. In this experiment, you will use a servo potentiometer to measure
angular position of a DC motor. In either case the principle is the same: the
potentiometer is used as a voltage divider that produces an output voltage linearly
dependent on angular position (note that audio pots are logarithmic). Since the
potentiometer mounted on the motor setup is a servo (continuous) potentiometer, its shaft
can be rotated indefinitely, but there is a small “dead-zone” of about 5-10 degrees that
will produce no output voltage. The bench potentiometer, in contrast, is a single-turn pot
(which is a misnomer since it achieves much less than a full rotation) with physical stops
at the extreme positions. Ultimately, for a servo-pot with a 5 degree dead-zone and 5
volts applied across the pot, we find voltage relationship similar to:
θ θ
Vout = Vin ≅ 5v
θ max 355°
For the above relationship for Vout to be true, we must prevent current from flowing
through the wiper. To assure this, the wiper signal must first be buffered, as shown in
Figure 1. We do not need to buffer the signal connected to the data acquisition board
since the board has a very high input resistance. Since pots often use wire windings, the
wiper produces electrical noise as it travels across the winding, and hence it is especially
important to use a low pass filter when differentiating the signal from a pot. The filter is
placed after the buffer. The filtered signal can then be differentiated to determine angular
velocity. A diagram of this circuit is shown in Figure 1. The most important thing to
avoid when using a pot in this fashion is the possibility of connecting the 5 volt
supply or Ground to the wiper, which will burn out the pot when the wiper
approaches the Grounded or 5 volt supply terminals, respectively.

Figure 1. Buffer amplifier filter differentiator circuit.

Page 1 of 5 Rev. 11/5/2001


Tachometers
A tachometer is essentially a generator; a DC motor run in reverse. The DC motor, or
tachometer, consists of multiple loops of copper wire that can rotate through a magnetic
field, typically provided by a fixed permanent magnet. These loops of wire are connected
via brushes and a commutator ring to the external electrical leads. In the case of a
generator, when the loops rotate through the field a nominal voltage is produced and can
be measured at the electrical leads. The faster the generator rotates, the greater the
voltage. Assuming that the electrical leads are connected to a device with high input
resistance (such as an op-amp circuit or a measurement device such as a voltmeter or
DAQ) this produces a linear relationship:
Vout = k Bω
where kB is the back-emf constant. Weaknesses of the tachometer include noise
produced by the internal brushes, voltage fluctuations caused by the individual loops of
wire moving through the field, and small output voltages at low speeds. Hence, it is wise
to buffer, amplify, and filter the signal from a tachometer rotating at low speeds, as
shown in Figure 2. Note that the last op-amp in this circuit inverts the inverted signal
from the filter and uses equal resistors to provide unity gain.

Figure 2. Buffer amplifier filter inverter circuit.


Measuring Phase
In this lab, you will be required to measure the phase between two different voltage
signals. Given two signals with the same frequency, you can calculate the phase between
them based upon the time between the peaks of the signals and the period, T, of the
signals. An example calculation, refering to Figure 3, for phase φ based upon the peak
time of the first signal, tp1, and the second signal tp2 is:
t p1 − t p 2
φ= 360°
T

Figure 3. Measuring phase difference.

Page 2 of 5 Rev. 11/5/2001


Laboratory Exercise
- WARNING! The pendulum makes an effective weapon! -
- Keep hands and heads clear! -
1. Be sure the bench power supply is turned off!
2. In order to measure the angular response of the pendulum, connect the wiper
(YELLOW banana jack on setup) to AI_CH0 on the DAQ terminal block.
3. Connect the motor terminals to the amplifier power outputs (the + and – banana plug
jacks) on the bench power supply.
4. Apply a sinusoidal signal from the function generator to the power-amplifier that
drives the motor (the coaxial BNC connection labeled Vref on the bench power
supply). Also connect the output from the function generator to AI_CH1. It is
important that the DC offset of the signal is at or near zero, which can be checked via
the oscilloscope or the CVI program that will be opened next.
5. Turn the bench power supply on. The pendulum attached to the motor should
oscillate. Try to get the largest (by adjusting the signal generator amplitude) and
fastest (by adjusting the signal generator frequency) oscillation you can without the
pendulum spinning around. Make sure that the pendulum is balanced on the shaft, so
that it will oscillate through the same region throughout the experiment. Also try to
avoid having the potentiometer oscillate through its dead zone.
6. Start CVI and load and run the project "POT.PRJ" from the
"C:\CVI\PROGRAMS\LABS\POT" folder. Set the appropriate sampling rate and
number of samples and start the program. There should be two waveforms displayed
by CVI, one is the output signal from the potentiometer and the other is function
generator input signal. Depending on the quality of signal from your pot, you may
choose to buffer, filter, and amplify the signal from the potentiometer according to
Figure 2 (substituting vtach with vwiper) to get the best resolution from the data
acquisition card and reduce the presence of noise.
7. The CVI program will allow you to capture the signals from the pot and signal
generator. Save the file to disk. The data file contains three columns. First column is
time, second column is output signal, and third column is input signal. Use a data-
plotting program such as MATLAB or EXCEL to plot your data.
What are the amplitudes of the signals and what is the phase difference between input
applied to the motor and the resulting potentiometer signal?

Page 3 of 5 Rev. 11/5/2001


8. Buffer, amplify, filter, and differentiate your pot signal according to Figure 1 to
obtain velocity information from the potentiometer output. Ensure that you have a
low pass filter built into your differentiator with a cutoff frequency at least twice as
high as the oscillating frequency of the pot. Connect the output from the
differentiator to AI_CH0 and the function generator signal of AI_CH1. Set the
appropriate sampling rate and number of samples and start the program. Save the file
to disk. The data file contains three columns. First column is time, second column is
differentiated potentiometer signal, and third column is input signal. Use a data-
plotting program such as MATLAB or EXCEL to plot your data.
What is the amplitude of the velocity signal and the phase difference from the input to
the output? Is this phase expected? Why or why not?

9. With the differentiated signal from the potentiometer still connected to AI_CH0,
connect the output voltage of the tachometer to AI_CH1 of the DAQ terminal block
via the circuit in Figure 2 so that you can see the signal. Again, make educated
decisions on the cutoff frequency and system gain for your circuit. Set the
appropriate sampling rate and number of samples and start the program. Save the file
to disk. The data file contains three columns. The first column is time, second
column is differentiated potentiometer signal, and third column is tachometer voltage
signal. Use a data-plotting program such as MATLAB or EXCEL to plot your data.
Compare the signal from the tachometer with the information provided by
differentiating the voltage from the potentiometer.
What is the phase difference between these signals?

Page 4 of 5 Rev. 11/5/2001


Questions:
1. Briefly describe at least two advantages of using a potentiometer for both position
and velocity measurement.

2. Briefly describe at least two disadvantages of using a potentiometer for both position
and velocity measurement.

3. Briefly describe at least two advantages of using a tachometer for velocity


measurement.

4. Briefly describe at least two disadvantages of using a tachometer for velocity


measurement.

5. How could you use a potentiometer or tachometer in your robotics project?

Page 5 of 5 Rev. 11/5/2001

You might also like