S‐LCD3 eBike Display User Manual V1.

0
Hold button to start up and enter display 1.
Dear customer, please read this manual before you use S‐LCD3 instrument. The manual will guide
you use the instrument correctly to achieve a variety of vehicle control and vehicle status display. 2.1 Turn on backlight and headlights
Functions and Display Hold long to turn on backlight and headlights (the controller
Instruments using the structure form of instrument body portion and the operation buttons are should have headlight drive output function); hold long again to turn
designed separately. off the backlight and headlights.
2.2 Assist ratio gear (ASSIST) switch
Hold or shortly to switch 1‐5 file gear. Gear 1 is for the
minimum power, gear 5 is for the highest power. Each startup will
automatically restore the gear shutdown last time(the user can set
randomly). Gear 0 is without booster function.
2.3 6Km/H assist promotion function
1 UP Button 10 6Km/H push power assist
2 SW Button Km/H Riding speed(metric) Hold and flashes, the vehicle drives at the speed not more
3 DOWN Button MPH Riding speed (imperial) than 6Km /h. Release button, the function is invalid.
11
4 Battery capacity indicator MXS MAX speed 2.4 Cruise function
5 Backlight and headlights AVS Average speed After the cruise function is turned on, the trip riding speed is greater
6 The brake display Km Distance(metric) than 7 km/ h, hold long and enter cruise, the CRUISE lit. Brake or
TM Single trip time Mil Distance (imperial) hold any button to cancel.
7
TTM Total trip time 12 DST Trip distance 2.5 Display and delete of single data

MOTOR W Power display ODO Total distance After power on for 5 seconds, hold and at the same time,
8 MOTOR ℃ Motor temperature VOL Battery voltage single trip riding time (TM) and single trip distance (DST) flash, hold

MOTOR ℉ Motor fahrenheit ASSIST Pas level button shortly, the content of both is cleared. If failed holding the
13 button within 5 seconds, it will automatically return the display interface after 5 seconds, original
℃ Environment temperature CRUISE Cruise
9 content is preserved.
℉ Environment fahrenheit
3. Display 2
Operation
1. ON/OFF
Hold button shortly in display 1 to enter display 2.
Hold button long to turn on the power, and hold long for a second time to turn off the
power. When the motor stops driving and when the e‐bike is not used for a consecutive 5 minutes, it will
In the riding mode after 5 seconds, display 2 automatically returns to display 1, and the original
automatically shut down and turn off the motor power supply.
motor power (MOTOR W) display is replaced with motor operating temperature display
2. Display 1
(MOTOR ℃) display (the internal motor should be equipped with the temperature sensor and the The wheel diameter will be set after finishing setting the maximum
output of temperature detection signal). riding speed, wheel diameter specifications flashes. Hold or
4. Display 3 shortly to set the specifications of wheel diameter. Select the range
6,8,10,12,14,16,18,20,22,24,26,700c and 28 inches. Hold button
Hold button shortly in display 2 to enter display 3. shortly and go to the next parameter settings.
3. Set the metric units
In the riding condition, five seconds later, a single maximum speed (MXS) display automatically The metric units will be set after finishing setting wheel diameter,
returns to the real riding speed (Km/H). Km/H and Km flash. Hold or shortly and select the three
5. In display 3, hold button shortly (SW),and the display will re‐enter display 1. metric units of speed, mileage, and ambient temperature in
6. Hold button to turn off the display and the power supply of controller. synchronization.
7. Automatically prompt interface Display Metric Imperial
7.1 Error Code display Error Code Definition Riding speed Km/H MPH
01＿info Throttle Abnormality Total distance Km Mil
03＿info Motor hall signal Abnormality Environment temperature ℃ Temperature ℉ Fahrenheit
04＿info Torque sensor signal Abnormality 4. Km/H and Km stop flash after metric unit setting is completed. Hold button shortly again to
05＿info Axis speed sensor Abnormality(only applied to torque re‐enter the maximum riding speed setting interface; or hold button long to exit from setting
sensor) environment of routine projects and save the setting values, returning to display 1.
06＿info Motor or controller has short circuit Abnormality 5. Exit from routine project setting
Electronic control system failure will display (flashing) fault code. Once the fault was removed, it All three routine project settings can exit from the setting environment and return to the display
automatically exits from the fault code display interface. if hold button long after each setting is completed, meanwhile the setting values are saved.
7.2 Motor temperature alarm Under each setting interface, if the button failed holding for more than 1 minute, it will
When the motor temperature (the internal motor should be equipped with the temperature automatically return to display 1, and the setting value is invalid.
sensor and the output of temperature detection signal) is over the warning value, MOTOR ℃ (℉) Outline Drawings and Dimensions
flashes to alarm at any display, meanwhile the motor controller will offer the appropriate protection to 1. Dimensions of main instrument body 2. Mounting dimensions of double brackets
motor.
General Project Setting
1. Set maximum riding speed
After power on for 5 seconds, hold and at the same time,
maximum riding speed Km/H and MXS flash, hold or shortly
to set the maximum riding speed (default 25Km/H). Hold button 3. Dimensions of button box 4. Wiring diagram
shortly and go to the next parameter settings.
2. Wheel diameter setting
Prepared by Guangzhou Electrony Corporation