6 7 8 9 10

43 44

11
12 42 45
5 13 46
47
41
14

777
15
4
3

384
∅157 H7/k6
∅125 H7
∅150 H7

∅ 75 k6

∅68 h11
∅96 H8
∅70 k6

∅56 k6
2 Highest oil level
Lowest oil level
1
16 6x ∅27
17
18
400 ±0.11
19 385
20
800 539
21
951 613

∅240 H8/h7

∅105 k6

40 22 SYSTEM'S TECHNICAL SPECIFICATION

∅137 H8 Shaft
Motor Shaft I Shaft II Shaft III
∅108 h11 Specification
39 23 Ratio, u 3.5 15 4.2893
∅125 H7
∅75 k6
Power, P, kW 9.74 9.35 7.59 7.21
∅115 H8/k7 ∅80 H8/k7
Rated Speed, n, rpm 1460 730 48.6667 11.346
38 24 Torque, T, N.mm 63710.274 122318.4932 1489407.534 6068702.626

∅120 H7/k6 ∅85 H7/k6

TECHNICAL REQUIREMENTS 30 33115/Q Tapered roller bearings 2 Chrome Steel ISO 492
37 25 1. The body and and the lid of the box need to apply a layer of glue-glass before assembling.
29
28
22x14x100
m=10, z=30
Key
Worm drive
1
1
C45-Steel
C45-Steel
2. The taper pin is used as a reference in both manufacturing and installation. 27 16x10x74 Key 1 C45-Steel
3. The non-manufacturing sides of the box should be painted blue for the outside and red for the inside.
4. All the transmission system of the box should be rotated easily by hand after assembling. 26 m=4,z=36, β=17.2539 Helical gear z 1 1 C45-Steel
5. It is recommended to operate without loads for 2 hours before using . 25 22x14x180 Key 1 C45-Steel
6. Grease-lubricated roller bearings, oil-lubricated reducers box. The oil must be changed regularly.
36 26 8. Leave a thermal gap between the roller bearing cover and the box wall for 0.1mm.
24 a= 8mm,l= 54mm Oil barrier for shaft II
23 ∅125x∅180x0.1 Steel plate
2
2
GX15-32
C45 Steel
9. Fit tolerances for Keys and Keyways: N9/js9.
∅85 H7/k6 22 D=125mm,D₂=181mm Housing's cover shaft II 2 GX15-32
21 21314 E Spherical roller bearings 1 Chrome Steel ISO 492
20 Oil Spreader 1 C45-Steel
19 m=10, z=2 Worm Screw 1 C45-Steel
27 18 Shaft I 1 C45-Steel
17 33115/QDFC150 Matched tapered bearings 1 Chrome steel ISO 492
∅110 k6
16 Bushing 1 SUJ2
∅240 H7
15 Oil seal 1 Rubber
35 14 D=185mm, D₂=219mm Housing's through cover shaft I 2 GX15-32
28 13 M20X2.5 Hex. Nut 8 Steel DIN 934
12 M20 Split Washer 8 Steel DIN 128A
∅240 H8/h7 ∅125 H8/h7
11 M20X1.5X150 Hex. head screw 4 Steel DIN 933
10 Observation door 1 GX15-32
47 M16X2 Hex. Nut 6 Steel DIN 934 9 M27X2 Vent plug 1 Ceramic
34 33 32 31 30 29 46 M16 Split Washer 6 Steel DIN 128A 8 M10X1.5X30 Hex. Head Screw 6 Steel DIN 933
45 M16X2X65 Hex. head screw 6 Steel DIN 931 7 M12X1.75X40 Hex. Head Screw 24 Steel DIN 933
44 M20X1.5X210 Hex. head screw 4 Steel DIN 931 6 M24 Lifting Eye Bolt 2 Alloy Steel DIN 580
43 M16X2X50 Hex. head screw 1 Steel DIN 931 5 δ=14mm Gearbox's lid 1 GX15-32
42 Taper pin 2 Steel DIN 1474 4 δ=15mm Gearbox's body 1 GX15-32
41 28x16x115 Key 1 C45-Steel 3 Oil dip stick 1 Aluminium
40 Oil seal 1 Rubber ISO 492 2 M20X1.5 Rubber basket 1 Rubber
39 D=240mm,D₂=307mm Housing's cover shaft III 1 GX15-32 1 M20X1.5 Oil drain plug 1 Steel
38 Shaft III 1 C45-Steel No. Symbol Name Q.ty Material Notation
37 m=4,z=155, β=17.2539 Helical gear z 2 1 C45-Steel
36 32x18x180 Key 1 C45-Steel
TRANSMISSION SYSTEM FOR CHAIN CONVEYOR DESIGN PROJECT
35 l=54mm,a=8mm Oil barrier for shaft III 2 GX15-32 Func. Full name Sign Date Quantity Weight Ratio
Name H.N.Thông 12/12 DRAWING OF 2-SPEED 900kg
34 D=240mm,D₂=307mm Housing's cover shaft III 1 GX15-32 1 1:2
33 30322 J2 Spherical roller bearings 2 Chrome Steel ISO 492 Instruct. N.V.Thịnh GEARBOX Sheet:1 Total sheet:2
32 ∅240x∅307x0.1 Steel plate 2 C45-Steel Approve NATIONAL UNIVERSITY-HCMC
31 Shaft II 1 C45-Steel UNIVERSITY OF TECHNOLOGY