HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL
ORIGINAL MANUAL ISSUE DATE: 4/2015
GN1T CHASSIS
Segment: XFL
Version Date Subject
1.0 4/2015 Original manual issue.

LCD TV

9-888-570-01
SERVICE MANUAL
GN1T CHASSIS
Segment: XFL

LCD TV

9-888-570-01
MODEL LIST

MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST.

KD-43X8301C Black RMT-TX100D CEI KD-49X8301C Black RMT-TX100D CEI
(FW-43X8370C) (FW-49X8370C)

KD-43X8305C Black RMT-TX100D CEI

UKA KD-49X8305C Black RMT-TX100D CEI
RMT-TX100E RU3 UKA
RMT-TX100E RU3
KD-43X8307C Silver RMT-TX100D CEI
UKA KD-49X8307C Silver RMT-TX100D CEI
RMT-TX100E RU3 UKA
RMT-TX100E RU3
KD-43X8308C Black RMT-TX100D CEI
UKA KD-49X8308C Black RMT-TX100D CEI
UKA
KD-43X8309C Black RMT-TX100D CEI RMT-TX100E RU3
UKA
KD-49X8309C Black RMT-TX100D CEI
UKA

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 3

WARNINGS AND CAUTIONS - ENGLISH

CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.

CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.

SAFETY-RELATED COMPONENT WARNING!!

Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony
parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Follow these procedures whenever critical components are replaced or improper operation is suspected.

CAUTION ABOUT THE LITHIUM BATTERY

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Outer case broken battery should not contact to water.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 4

WARNINGS AND CAUTIONS - FRENCH

ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement.
Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.

WARNING!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est
directement raccordé à l’alimentation du secteur.

POUR TRANSPORTER LE TÉLÉVISEUR

Tenez compte de ce qui suit pendant l’installation du téléviseur :
• Débranchez tous les câbles avant de transporter le téléviseur.
• Transportez le téléviseur avec le nombre de personnes approprié ; un téléviseur de grande taille doit être transporté par au moins deux personnes.
• Lors du transport du téléviseur, l’emplacement des mains est très important pour votre sécurité, ainsi que pour éviter de causer des dommages.

ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chassis sous tension, un transformateur d’isolement doit etre utilise lors de tout depannage. Le chassis de ce recepteur est
directement raccorde a l’alimentation du secteur.

ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!

Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du
fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages
de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de
composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.

AVERTISSEMENT CONCERNANT LA BATTERIE AU LITHIUM

• Il existe un risque d’explosion si la batterie n’est pas correctement remplacée. Utilisez uniquement un type de batterie similaire ou équivalent.
• Lorsqu’il est endommagé, le boîtier externe de la batterie ne doit pas entrer en contact avec l’eau.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 5

 WARNINGS AND CAUTIONS

USE CAUTION WHEN HANDLING THE LCD PANEL

When repairing the LCD panel, be sure you are grounded by using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.

1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).

10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 6

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.

7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 7

 SAFETY CHECK-OUT

Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’
instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all
battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also
at earth ground.
If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance
between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot
side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the
lamp should light at normal brilliance if the screw is at ground potential (see Figure B).

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 8

SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.

DIAGNOSTIC TEST INDICATORS

When an error occurs, the Smart Core Red LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
<G>: Power supply board, <B>: Main board, <T>: Tcon board, (LD) board ,
If the screen displays a “0”, no error has occurred . <P>: Panel module , <S>: Speaker , <A>: Power Adapter

RED LED blinking count Detection Items

2x <G/B> Main 12V over voltage [MAIN_POWER]

<B> Main 5.0V failure [DC_ALERT]

3x <B/S> Audio amp. protection [AUD_ERR]

<B> Tuner or demodulator I2C No ACK [TU_DEMOD]
<B> HDMI Switch/Equalizer I2C communication error [HDMI_EQ]

4x None

<P/T/G/B> Panel ID EEPROM I2C No ACK (Also panel power failure is a suspect) [P_ID_ERR]
5x
<T> TCon IC I2C communication error [TCON_ERR]

6x <G/P/B> Backlight failure [BACKLIGHT]

Over temperature protection [TEMP_ERR]

7x <B> Temp. sensor I2C No ACK [TEMP_ERR]
<B> V By One lock error between Main device and 4KBE device [4KBE_ERR]

8x <B> Software error [SW_ERR]

Red italic: detect at startup sequence only.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 9

 SELF DIAGNOSIS FUNCTION

[SELF DIAGNOSTIC SCREEN DISPLAY]

Error count
Error item Naming

Format of error timestamps SELF CHECK

YYMMDDhhmmss (in UTC)
Example: Back
120823132523 -> Aug 23 2012 13:25:23 UTC
<<
* Only when time is set, an error timestamp 002 MAIN_POWER 000000000000 000000000000 000000000000 000
is saved. 003 DC_ALERT 000000000000 000000000000 000000000000 000
003 AUD_ERR 150101000018 150101000018 150101000018 003
003 HDMI_EQ 150101000123 150101000045 150101000045 003
003 TU_DEMOD 150101000218 150101000223 150101000105 003
004 LD_ERR 000000000000 000000000000 000000000000 000
Smart Core Red LED 004 BCM_ERR 000000000000 000000000000 000000000000 000
blinking count
005 TCON_ERR 150101000504 000000000000 000000000000 001
005 P_ID_ERR 000000000000 000000000000 000000000000 000
006 BACKLIGHT ERR 000000000000 000000000000 000000000000 000
007 TEMP_ERR 150101000200 150101000002 000000000000 002
007 4KBE_ERR 000000000000 000000000000 000000000000 000
008 SW_ERR 000000000000 000000000000 000000000000 000

00005 00414 00002

•Panel Operation Time is recorded every [Home]Exit
30 min, but Total Operation Time is recorded every 1 hr.
Therefore, the panel op. time might become larger than Error Error Error
the total op. time. timestamp for timestamp for timestamp
last recorded second last for 3rd last
error recorded error recorded
error

Total Operation Time [hr] – Boot Count – Panel Operation Time [hr]

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 10

 SELF DIAGNOSIS FUNCTION

SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.

Clearing the Self Check Diagnostic List

Panel operation time : Press the Channel 7 => Channel 0 .

Exiting the Self-diagnostic screen

To exit the Self Diagnostic screen, Power off & on or Push the <Home> button.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 11

SEC 1. DISASSEMBLY
• There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts.
1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C
1-1-1. STAND

4 screws (SCREW, +PSW M5X16) P/N: 4-449-743-01

STAND

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 12

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-2. LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W) AND LABEL, CI

LABEL, CI

LABEL, REAR TERMINAL

LABEL, SIDE TERMINAL (W)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 13

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-3. AC COVER AND POWER SUPPLY CORD

Screw (SCREW, +PWH M3X6) P/N: 4-452-935-11

2 3 4 POWER SUPPLY CORD 5

AC COVER

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 14

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-4. REAR COVER (SM HRN) A

9 screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: 2-580-639-01

4 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01
9 screws (SCREW, +PWH M3X6) P/N: 4-452-935-11

2
3
REAR COVER (SM HRN) A

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 15

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-5. TAPE AND WIRE DRESSING

TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 16

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-6. TAPE AND WIRE DRESSING

TAPE
TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 17

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-7. SPEAKER BOX ASSY (L)

2 3

SPEAKER BOX ASSY (L)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 18

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-8. SPEAKER BOX ASSY (R)

2 3

SPEAKER BOX ASSY (R)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 19

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-9. TAPE

TAPE

TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 20

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-10. BT ANTENNA

BT ANTENNA
2 3 4

Screw (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 21

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-11. SMART CORE
1

2 3
SMART CORE

Notes on assembling the Smart core

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 22

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-12. SWITCH UNIT

Release the lock

2 3

SWITCH UNIT

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 23

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-13. HARNESS ASSY (MAIN) AND CONNECTOR ASSY 28P

HARNESS ASSY (MAIN)

P/N: 1-910-110-20

CONNECTOR ASSY 28P

P/N: 1-910-110-19

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 24

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-14. BRACKET,SC (HRN)

2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3
BRACKET,SC (HRN)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 25

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-15. SLIDE, CLAMP

2
SLIDE, CLAMP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 26

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-16. BOTTOM, FRAME (HRN)

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2
3

BOTTOM, FRAME (HRN)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 27

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-17. BRACKET, SP (LAK)
1

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3
BRACKET, SP (LAK)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 28

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-18. GL4

4 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-11

2 3

GL4

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 29

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-19. SHEET, INSULATION(HRN S)
(An insulation sheet is under the GL4 power supply board.)
1 2

SHEET, INSULATION(HRN S)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 30

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-20. FLEXIBLE FLAT CABLE 41P (XFA) AND FLEXIBLE FLAT CABLE 51P (XFA)

TAPE

FLEXIBLE FLAT CABLE 51P (XFA)

2 FLEXIBLE FLAT CABLE 41P (XFA) 3 P/N: 1-848-920-11
P/N: 1-848-925-11

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 31

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-21. BRACKET, SIDE F (MOLD)

3
2

BRACKET, SIDE F (MOLD)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 32

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-22. BRACKET, TOP FL (MOLD)

3
2

BRACKET, TOP FL (MOLD)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 33

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-23. BMFW ASSY

1
<1> <2>

<1>
<1>

<1>

<1>
<1> <3>

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

BMFW ASSY

2 3

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 34

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-24. GASKET (BMF) GASKET (BMF)

GASKET (BMF)

NOTE:
When you replace a BMFL board, it is necessary to
stick five new GASKET on a new BMFL board.
GASKET (BMF): 4-566-117-01

However, there are sets that mount the surface

mount type gasket.
In that case, replacing the GASKET is nor
necessary
Because it is soldered on the board and
Impossible to detach

To stick the GASKET firmly,

Stick GASKET inside the guide line.
Press the gasket until compression completely.
(0.5-1.0kgf)

Guide line
*No indication of direction

Caution:
1. Please aim at the center of square land.
2. Assy the gaskets just before B board panel installation.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 35

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-25. SHEET, THERMAL(BM)

SHEET, THERMAL(BM)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 36

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-26. PLATE, MAIN S (HRN)

1 2 3

PLATE, MAIN S
(HRN)
2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

1 2 3

PLATE, MAIN S
(HRN)
2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 37

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-27. SLIDE, CLAMP

2
SLIDE, CLAMP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 38

 DISASSEMBLY

1-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

1-1-28. LCD PANEL

LCD PANEL

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 39

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-1. STAND

4 screws (SCREW, +PSW M5X16) P/N: 4-449-743-01

STAND

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 40

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-2. LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (W) AND LABEL, CI

LABEL, CI

LABEL, REAR TERMINAL

LABEL, SIDE TERMINAL (W)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 41

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-3. AC COVER AND POWER SUPPLY CORD

Screw (SCREW, +PWH M3X6) P/N: 4-452-935-11

2 3 4 POWER SUPPLY CORD 5

AC COVER

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 42

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-4. REAR COVER (M HRN) A

9 screws (SCREW, +BVTP 4X12 TYPE2 IT-3) P/N: 2-580-639-01

4 screws (SCREW, +PSW M4X10) P/N: 4-159-298-01
10 screws (SCREW, +PWH M3X6) P/N: 4-452-935-11

2
3
REAR COVER (M HRN) A

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 43

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-5. BRACKET, VESA

4 Screws (SCREW +BVTP 3X8 TYPE2 IT-3) P/N: 7-685-646-79

2
3

BRACKET, VESA

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 44

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-6. TAPE AND WIRE DRESSING

TAPE

TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 45

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-7. TAPE AND WIRE DRESSING

TAPE
TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 46

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-8. SPEAKER BOX ASSY (L)

2 3

SPEAKER BOX ASSY (L)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 47

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-9. SPEAKER BOX ASSY (R)

2 3

SPEAKER BOX ASSY (R)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 48

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-10. TAPE

TAPE

TAPE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 49

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-11. BT ANTENNA

BT ANTENNA
2 3 4

Screw (SCREW (+PSW) (M3X6))

P/N: 2-990-421-41

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 50

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-12. SMART CORE

2 3
SMART CORE

Notes on assembling the Smart core

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 51

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-13. SWITCH UNIT

Release the lock

2 3

SWITCH UNIT

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 52

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-14. HARNESS ASSY (MAIN) AND CONNECTOR ASSY 28P

HARNESS ASSY (MAIN)

P/N: 1-910-110-22

CONNECTOR ASSY 28P

P/N: 1-910-110-21

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 53

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-15. BRACKET,SC (HRN)

2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3
BRACKET,SC (HRN)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 54

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-16. SLIDE, CLAMP

2
SLIDE, CLAMP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 55

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-17. BOTTOM, FRAME (HRN)

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3

BOTTOM, FRAME (HRN)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 56

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-18. BRACKET, SP (LAK)
1

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

2 3
BRACKET, SP (LAK)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 57

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-19. GL4

4 screws (SCREW, +PSW M3X6 W12) P/N: 4-256-393-11

2 3

GL4

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 58

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-20. SHEET, INSULATION (HRN S)
(An insulation sheet under the GL4 power supply board.)
1 2

SHEET, INSULATION(HRN S)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 59

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-21. FLEXIBLE FLAT CABLE 41P (XFB) AND FLEXIBLE FLAT CABLE 51P (XFB)

TAPE

2 FLEXIBLE FLAT CABLE 41P (XFB) 3 FLEXIBLE FLAT CABLE 51P (XFB)
P/N: 1-848-926-11 P/N: 1-848-921-11

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 60

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-22. BRACKET, SIDE F (MOLD)

3
2

BRACKET, SIDE F (MOLD)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 61

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-23. BRACKET, TOP FL (MOLD)

3 BRACKET, TOP FL (MOLD)

2

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 62

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-24. BMFW ASSY

1
<1> <2>

<1>

<1>

<1>

<1>
<1> <3>

8 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

BMFW ASSY
2 3

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 63

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-25. GASKET (BMF) GASKET (BMF)

GASKET (BMF)

NOTE:
When you replace a BMFL board, it is necessary to
stick five new GASKET on a new BMFL board.
GASKET (BMF): 4-566-117-01

However, there are sets that mount the surface

mount type gasket.
In that case, replacing the GASKET is nor
necessary
Because it is soldered on the board and
Impossible to detach

To stick the GASKET firmly,

Stick GASKET inside the guide line.
Press the gasket until compression completely.
(0.5-1.0kgf)

Guide line
*No indication of direction

Caution:
1. Please aim at the center of square land.
2. Assy the gaskets just before B board panel installation.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 64

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-26. SHEET, THERMAL(BM)

SHEET, THERMAL(BM)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 65

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-27. PLATE, MAIN S (HRN)

1 2 3

PLATE, MAIN S
(HRN)

2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

1 2 3

PLATE, MAIN S
(HRN)
2 screws (SCREW (+PSW) (M3X6)) P/N: 2-990-421-41

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 66

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-28. SLIDE, CLAMP

2
SLIDE, CLAMP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 67

 DISASSEMBLY

1-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

1-2-29. LCD PANEL

LCD PANEL

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 68

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-1. WLAN / BT MODULE (11AC) ASSY

2
WLAN / BT MODULE(11AC) ASSY

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 69

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-2. WLAN / BT MODULE (11AC)

1 2

Caution!
1 Avoid to touching on this components
and connector
WLAN / BT MODULE(11AC)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 70

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-3. SHEET, THERMAL (SC) AND HEAT SINK L (SC) AND BRACKET, WIFI

1 2 SHEET, THERMAL (SC)

3 4 HEAT SINK L (SC)

BRACKET, WIFI

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 71

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-4. COVER, TOP

COVER, TOP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 72

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-5. PANEL, ORNAMENT

2 3

PANEL, ORNAMENT

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 73

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-6. LIGHT, GUIDE

2 3
LIGHT, GUIDE

LOCK PORTION

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 74

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-7. HSC3_S_M MOUNT

1 2

HSC3_S_M MOUNT

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 75

 DISASSEMBLY

1-3. SMART CORE (ML)

1-3-8. CASE, BOTTOM (M)

CASE, BOTTOM (M)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 76

SEC 2. ADJUSTMENT
HOW TO ENTER THE SERVICE MODE
1) Turn on the main power switch to set in standby mode. 4) How to use the remote commander.
2) Press the buttons on the remote commander in the following sequence
with each interval within 1 sec, then the service mode will be set. Function The flow of control
Service mode on <Display><5><Vol Up><Power>
Service mode off <MENU>/<HOME>
Item up / down <↑>/ <↓>
Item select left/right <←>/<→>
3) Service mode display.
Execute <OK>

Service Mode
Model Information >> 5) After entering service mode, then turn off the power switch.
Self diagnosis History >>
Video / Audio >>
Panel / PQ >> Summary of key behavior
General Setting >>
Tuner >> Key Behavior
Wifi >> Menu Close service menu

Return Previous page, Change potion of focus item,

Cursor/Enter
Enter next page of focus item, etc..

[</>] Set [Home]Exit

Return Return to previous page, close service menu etc..

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 77

 ADJUSTMENT

SOFTWARE VERSION
1) In Service Mode, select “Model Information”, press “Enter” or → button to enter Status Information.

Main Micro
Service Mode Model SW Version: PKG2.011.0010NAB
NVM Version: 0001 UC2
Model Information >> Boot Version: V1.000
Self diagnosis History >> Status Information >> PQ Version: 102100006
AQ Version: AQ1.100
Video / Audio >> Model Information >> <Ext>
exFRC: 00.00.00.00
Panel / PQ >> Model Number Setting >> CameraVID: 0
General Setting >> SERIAL NUMBER EDIT >> CameraPIC: 0
Tuner >> CameraFW: 0
4k BE
Wifi >> MLFW: SF1.002
MAFW: SF0.360
ADSP SF0.501
NDAT SD0.370
PDAT SD0.370
BDAT SD1.011
BCM SD-------
FDAT SD0.002
[</>] Set [Home]Exit [</>] Set [Home]Exit UDAT SD0.000
BDIX SD0.370

2) Press “Enter” or “Return” button to return to Service Mode.

Service Mode
Model Information >>
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi >>

[</>] Set [Home]Exit

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 78

 ADJUSTMENT

SERIAL NUMBER EDIT (1)

Service Mode
1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” then pressing “Enter” or Model Information >>
Self diagnosis History >>
“→” button to enter inside. Video / Audio >>
Panel / PQ >>
General Setting >>
2) Select “Serial Number Edit” by pressing “↑” or “↓” button then pressing “Enter” or “→” button Tuner >>
Wifi >>
3) Press “↑” or “↓” to input numbers.
4) After user input data , press <Enter> . [</>] Set [Home]Exit

• Pop-up dialog appear to confirm input data correct

Mode
• Serial Number can be set ONLY ONCE
Status Information >>
Model Information >>
Model Number Setting >>
5) Press “→” or “←” button to select YES or NO. Select YES if input data is correct. Select NO if Serial Number Edit _ _ _ _ _ _ _

input data is incorrect. Press <Enter> to save answer.

Service Mode

Status Information >>

Model Information >>
Model Number Setting >>
Serial Number Edit 9 9 9 9 9 9 9

Input Data correct?

Yes No

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 79

 ADJUSTMENT

SERIAL NUMBER EDIT (2)

Service Mode
If YES is selected, the input data is saved into EEPROM.
SERIAL NUMBER EDIT is greyed out and the serial number that has been input is displayed. Status Information >>

>>
User will not able to edit anymore. Model Information

Model Number Setting <[ KDL-40X500B ]>

Serial Number Edit 9999999

If NO is selected, the input data is not saved into EEPROM. Service Mode

The serial number that has been input is displayed. >>

Status Information
User can still edit the Serial Number. Model Information >>

Model Number Setting <[ KDL-40X500B ]>

Serial Number Edit 9 9 9 9 9 9 9

Input Data correct?

Yes No

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 80

 ADJUSTMENT

MODEL NUMBER SETTING

1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
2) Select “Model Number Setting” by pressing “↑” or “↓” button then pressing “Enter” or “→” button.
3) Press “↑” or “↓” arrow key to scroll Product Name Candidate.
 (e.g. KDL-40X500B CO1,KDL-40X500C BR6)
4) Select one Product Name from the list, press <Enter> will pop dialog to inform user to confirm data. Model dependent settings will be overwritten into EEPROM.

Service Mode Service Mode [MODEL_NUMBER_SETTING]

Model Information >>
Status Information >>
Self diagnosis History >>
Model Information >>
Video / Audio >>
Model Number Setting >>
Panel / PQ >>
General Setting >> Serial Number Edit >>
____________
Tuner >>
Wifi >>

OK

[</>] Set [Home]Exit

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 81

 ADJUSTMENT

WB ADJUSTMENT
(Please apply when main board or panel is replaced.) c. To change data , press “←” or “→” on remote commander.
In “Panel/PQ” service mode.
a. Go to “WB Adjustment” category by “↑” or “↓”.
Back <<
Service Mode R WB Gain <[ 0 ]>
Model Information >> G WB Gain <[ 0 ]>
Self diagnosis History >> B WB Gain <[ 0 ]>
Video / Audio >> R WB Offset <[ 0 ]>
Panel / PQ >> G WB Offset <[ 0 ]>
General Setting >> B WB Offset <[ 0 ]>
Tuner >>
Wifi / BT >>

[</>] Set [Home]Exit

b. To select “WB Adjustment”, press “→” button.

[</>] Set [Home]Exit

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 82

 ADJUSTMENT

WB/MURA/CUC DATA TRANSFER 2. In “WB/Mura/CUC data transfer”.

(Please apply when main board or panel is replaced.) a. Select “WB/Gamma data transfer” by pressing “↑” or “↓” on remote commander.
1. In “Panel/PQ” service mode. b. To change the items, press “←” or “→” on remote commander and press “Enter”
a. Go to “WB/Mura/CUC data transfer” category by “↑” or “↓”. button.
Selectable items are:
Service Mode 0. SoC to T-con
Model Information >>
1. T-con to SoC
Self diagnosis History >>
Video / Audio >> 2. Not atction
Panel / PQ >> c. Select “[start]” and press “Enter” button to start transfer.
General Setting >>
Tuner >>
Wifi / BT >> Back <<
WB/Gamma data transfer <[ 0. SoC to T-con ]>
Mura data transfer <[ 0. SoC to T-con ]>
CUC data transfer <[ 0. SoC to T-con ]>
b. To select “WB/Mura/CUC data transfer”, press “→” button.
[</>] Set [Home]Exit [Start]
c. To change data , press “←” or “→” on remote commander.

[</>] Set [Home]Exit

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 83

 ADJUSTMENT

HDD PERFORMANCE CHECK 3. A message "Please wait ..." is displayed during performance check processing.
1. In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then
pressing “Enter” or “→” button to enter inside.
Service Mode

Service Mode
Model Information >> Please wait…
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>

2. Select “HDD Performance[</>]

checkSet”[Home]Exit
by pressing “↑” or “↓” then pressing 4. Result OK or NG will be displayed after performance of HDD is checked
“Enter” or “→” button to enter inside.

HDD Performace Check

General Setting

Back << Result <[ NG ]>

Aging mode <[On/Off]> Back <<
HDD Performance Check >>
AAA >>
Update CI+ Credentials >>
Boot count reset >>
ECS Enable <[On/Off]>

[</>] Set [Home]Exit

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 84

 ADJUSTMENT

HDD RE-REGISTER
1) In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
2) Select “AAA” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.

Service Mode General Setting

Model Information >>
Back <<
Self diagnosis History >>
Video / Audio >>
Aging mode <[On/Off]>
Panel / PQ >> HDD Performance Check >>
General Setting >> AAA >>
Tuner >> Update CI+ Credentials >>
Wifi / BT >> Boot count reset >>
ECS Enable <[On/Off]>

[</>] Set [Home]Exit [</>] Set [Home]Exit

3) Result OK or NG will be displayed after HDD re-registration is succeed/failed.

HDD Performace Check

Result <[ NG ]>

Back <<

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 85

SEC 3. TROUBLE SHOOTING
3-1. TRIAGE

Chart of triage information

1. Confirm the claimed symptom.
2. Select that symptom from the chart.
3. Bring all the boards and cables listed for that symptom.
4. Follow the troubleshooting charts in the technical guides to isolate the board.
5. Chart Color Code.

RED DOT: Most likely defective part

BLUE TRIANGLE: Secondary possible defective part
BLACK TEXT: Board that may correct the symptom

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 86

 TROUBLE SHOOTING

3-2. NO POWER
3-2-1. NO POWER-PCU

No Power

Check STBY 3.3V NG Replace NG

C9030 Between G* Board to G* Board
On B* board B* Board Harness

OK OK

Harness

B* Board

u-Com Failure

DDCON/LDO

Main Device Failure

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 87

 TROUBLE SHOOTING

3-2-2. NO POWER-U-Com Failure (1/2)

START

Check MAIN_VCC
No
Check C9117 Voltage. No Check +3.3V_STBY R9175 Voltage. G-Board
Is the voltage >3.0V? R9144, CN9000 #26pin Is the voltage >1.6V?

Yes
Yes

No Check P_ON_VBUS No
Check R9186 Voltage. Check DC_OFF_DET P-on ucom #pin11 Change IC9017
Is the voltage >3.0V? IC9018 is >3.0V?

Yes
Yes

Check STBY_MHL No SOC

Check OPWRSB No R9176 Voltage. Muffin Check P_ON_#1 No
R9179 Voltage. Is the voltage >3.0V? problem P-on ucom #pin13 Change IC9017
Is the voltage 0V? is >3.0V?

Yes
Yes Yes
No problem
TV set stays in Check PGOOD_1 No 1.3 No POWER - DDCON/LDO
STBY MHL charge mode. R9173 Voltage.
Check 1.0V DDCON (IC9008)
Is the voltage >3.0V?

Try AC Off and On after few minutes.

Check POWER_ON No If #pin19 keep Low, change IC9017.
P-on ucom #pin19
If #pin19 goes High few seconds and downs to Low,
Is the voltage >3.0V?
Check G board and harness.
yes
A

Check P_ON_LNB No To the next page

P-on ucom #pin15 Change IC9017
Is the voltage >3.0V?

Yes

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 88

 TROUBLE SHOOTING

3-2-2. NO POWER-U-Com Failure (2/2)

From previous page

Yes

Check P_ON_#2 No
P-on ucom #pin14 Change IC9017
Is the voltage >3.0V?

Yes

Check ORESETB No
P-on ucom #pin12 Change IC9017
Is the voltage >3.0V?

Yes

Check X_SYSTEM_RST
No
P-on ucom #pin16 Change IC9017
Is the voltage >3.0V?

Yes

If PANEL_PWER_ON (R9172) is 0V
Check XRST No
Change IC9017
P-on ucom #pin17
Is the voltage >3.0V?

Yes

If BL_MUTE (R9174) is 0V
Check BL_ON No
Change IC9017
P-on ucom #pin18
Is the voltage >3.0V?
Yes

END
Ucom IC9017 is working OK

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 89

 TROUBLE SHOOTING

3-2-3. NO POWER: DC_OFF_DET check 3-2-4. NO POWER: DDCONs check

START
START

Check fuse No
F9xxx Change Fuse
Check Vdd No Is fuse OK?
C9118 Change IC9018
Is voltage >5V?
Yes
Yes Check Vcc voltage No Check POWER_ON P-on ucom #pin19
C9xxx
END Is voltage >12.0V? (Refer 1.2 No Power U-Com Failure)

Yes

Check Enable pin No

voltage 1.2 No Power U-Com Failure
Is voltage >2.5V?

Yes

Change DDCON IC

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 90

 TROUBLE SHOOTING

3-2-5. NO POWER: DDCON check

START

Check IC9403 Vcc voltage Check Vcc voltage No Check No

No
C9428 C9061 D9000 Change D9000
Is voltage >12V? Is voltage >3V? Is diode ?

Yes Yes Yes

Check G board and harness

Check Vcc voltage No Check No

C9061 D9001 Change D9001
Is voltage >4V? Is diode ?

Yes Yes
Check +5V_MAIN DDCON (IC9001)

Check Enable No
IC9010 #pin1 Change IC9010
Is voltage >2.5V?

Yes

Change DDCON
IC9009

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 91

 TROUBLE SHOOTING

3-2-6. NO POWER: LDOs check check

START

Yes

Check Vcc voltage No

C9xxx Check +3.3V_MAIN DDCON (IC9003)
Is voltage >3V?

Yes

Check Enable pin No

voltage 1.2 No Power U-Com Failure
Is voltage >3V?

Yes

Change LDO IC

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 92

 TROUBLE SHOOTING

3-3. STANDBY LED BLINKING

3-3-1. 2 Times Blinking (Main power Error) 3-3-2. 3 Times Blinking (DC Alert)

BMFL/BMFW board
2-time blinking

3-time blinking

Check +12V_REG DC_ALERT

at pin 13/15/17 of CN9000 Yes
G* Board
on B* Board, Check +5.0V_MAIN NG
IC9014,etc
Voltage > 13.2V ? at pin1 in IC8001, 4.959V
(B* Board)
<Voltage<5.285V?
No
OK

B* Board AUDIO

Go to Audio check point

TUNER
HDMI
Go to Tuner check point
Go to HDMI check point

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 93

 TROUBLE SHOOTING

3-3-3. 3 Times Blinking (Tuner Error)

BMF* board

3-time blinking

No
Tuner Error ? See other flows

Yes
[except JP:R6001,R6002,C6004,C6005,R1468,R1469]
Check the voltage of Main Tuner I2C / JL6010, JL6011 NG
[JP,EU:R6003,R6004,C6006,C6007,R1466,R1467]
Check the voltage of Sub Tuner I2C (EU,JP only) / JL6021,
JL6022
[JP only:R6005,R6006]
[If these parts are OK, check Muffin]
OK

Check TU_3.3V / JL6005 [FB6001,C6002,C6003]

Check TU_1.8V (except UC) / JL6006 NG [FB6004,C6014,C6015]
Check TU_DEM_3.3V (except UC) / JL6019 [FB6006,C6020,C6021]
Check TU_1.1V(JP/FB6800 tuner-side)
[FB6800,C6800]
[If these parts are OK, go to DDCON troubleshooting]

OK
NG
Check TU_12V(EU,JP only)/JL 6027 [go to “NO PICTURE@Tuner”]

OK

[Change Tuner Module](UC:TU6000,PAD/LA-ISDB/CH/HK:TU6001,EU:TU6003,JP:TU6802)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 94

 TROUBLE SHOOTING

3-3-4. 3 Times Blinking (Audio Error)

LED 3x blinking Yes

Segment “XS”?

No No
Audio Error ? See other flow
Replace B-K Harness Yes
B-K harness NG
OK ?
Yes

No

Go to page
Replace K-PWB Yes
Power Off Checking*1 K-PWB NG
OK ?

Go to page No
Power off Checking*2

Replace B-PWB Yes

B-PWB NG
OK ?

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 95

 TROUBLE SHOOTING

Note 1: Note 2:
(1) PVDD-GND short check (1) PVDD-GND short check
1) Power Off Checking*1 Measure impedance between PVDD and GND at C7706, Measure impedance between PVDD and GND at C7722, C7762, C7782,
C7707. C7834.
If impedance is <100Ω → NG
If impedance is <100Ω → NG
(2) LDO out short check
(2) LDO out short check
Measure impedance between +3.3V and GND at C9130.
If impedance is <100Ω → NG
Measure impedance between +3.3V and GND at
C7909.
Power Off Check*1 (3) Fuse open check If impedance is <100Ω → NG
Measure impedance of fuse F7700, F7702 5A (12.5V)
If fuse open → NG (3) Fuse open check
Measure impedance of fuse
F7702, F7704, F7705, F7701 5A (12.5V)
Segment “XS”? F7700 3.15A (DDC5V)
Yes If fuse open → NG

No
Power Off Check*3
(1) B-PWB (1) K-PWB
PVDD-GND short ? PVDD-GND short ?
(See Note 1) Yes (See Note 2) Yes

No No Measure the Speaker

impedance by multi-meter Replace Speaker
(2) B-PWB (2) K-PWB Less than 3Ω ? Yes
LDO out short ? LDO out short ?
(See Note 1) Yes (See Note 2) Yes No
Confirm the speaker
No No harness
Replace Speaker Harness
Cut or shorted Yes
(3) B-PWB (3) K-PWB
to the chassis ?
Fuse broken ? Fuse broken ?
(See Note 1) Yes (See Note 2) Yes No

No Replace B-PWB No Replace K-PWB Return to LED 3x blinking

or Power Off Checking*3

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 96

 TROUBLE SHOOTING

2) Power Off Checking*2

(4) 12.5V check BMFL / BMFW

Measure voltage between PVDD and GND at
capacitor C7706 or C7707.(See 3.3)
Power Off Check*2 Voltage rise more than 0V for a moment at
power on
→ Yes
Yes
Segment “XS”? (5) 12.5V check KS-PWB (XS)
Measure voltage between PVDD and GND at
capacitor C7722, C7762, C7782 or C7834. (See
No
3.3)
(5) 12.5V check
(4) 12.5V check Yes Voltage rise more than 0V for a moment at
12.5V is supplied to
12.5V is supplied to Yes power on
K-PWB for a moment
B-PWB for a moment → Yes
before LED 3x brinking ?
before LED 3x brinking ?
No
No

Yes Replace G-K Harness Yes

Replace B-K Harness
OK ?
OK ?

No No

Replace G-PWB Yes Replace G-PWB Yes

OK ? OK ?

No No
Return to Return to
LED 3x blinking LED 3x blinking
Finish Finish

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 97

 TROUBLE SHOOTING

3) Power Off Checking*3

No Sound
Without LED 3x
No sound only Yes Go to
Analog RF and Digital RF ? No Sound Tuner
Select [External Inputs]→
AV receiver is connected Yes
[BRAVIA Sync Settings]→
to HDMI in ?
[BRAVIA Sync Control]→[off] No
No
Yes Go to
No sound only HDMI ?
No Sound HDMI
[Speakers] setting is Yes Change the setting to
[Audio System] ? [TV Speakers] No

No Go to
No Sound Audio
Headphone is connected to Yes
Disconnect the Headphone
HP/Audio Out terminal ?

No
[Sound]→ Change [Sound]→
Yes
[Headphone Speaker Link] [Headphone Speaker Link]
setting is [On] ? Yes to [Off], OK ?
No No

Replace B-PWB
Go to
Power Off Checking*1 HP/Audio out terminal or Headphone detect
GPIO may be broken

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 98

 TROUBLE SHOOTING

3-3-5. 3 Times Blinking (HDMI EQ Error)

BMFL/BMFW board

3-time blinking Check

I2C_C bus signal. NG IC5212
at CL5259 and Or IC1000
CL5261.
Check
VS GND impedance NG
of +1.0V_HDMI IC5212 OK
at HDMI EQ side
(ex.C5335) Check
OK Voltage
of +1.0V_HDMI,
EQ_+3.3V_MAIN, NG Power,
Check +5V_BOSTON DDCON
VS GND impedance NG at HDMI EQ side
of EQ_+3.3V_MAIN IC5212 (ex.C5335, C5317,
at HDMI EQ side and C5351, )
(ex.C5317)
OK
OK
X’tal or
around parts.
Check
NG X5202,
Check Frequency of X’tal
R5478(100ohm),
VS GND impedance NG (X5202)
R5368(1Mohm)
of +5V_BOSTON IC5212 27MHz?
C5298(10pF)
at HDMI EQ side OK C5297(12pF)
(ex.C5351)

OK
IC1000

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 99

 TROUBLE SHOOTING

3-3-6. 4 Times Blinking (LED Voltage Error)

4-time blinking

Between 0.898V to 2.997V

Check LED driver or G* board

R9027
on the B* Board  Change LD board or G* board.

0.897V or less

B* Board

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 100

 TROUBLE SHOOTING

3-3-7. 5 Times Blinking (Panel Communication Error)

5-times blinking

NG
Change Change
B-Board Panel (T-con)
Check NG OK
“+12.5V_TCON” at G-Board is
Replace G-Board
CN9000 suspicious
Symptom Symptom
on the B-Board
improvement improvement
NG
OK B-Board is Panel (T-Con) is
suspicious suspicious
Symptom
Replace the Harness improve Harness is
Between G-Board
suspicious
and B-Board

NG

Symptom
improve
Replace V-By-One FFC
the V-By-One FFC is suspicious

NG

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 101

 TROUBLE SHOOTING

3-3-8. 6 Times Blinking (Backlight Error)

6-times blinking

Check a voltage of
Harness /
BL_ERR_DET. Check
Connection
Check point is Voltage ≥ 1.9 V harness/connection
broken Change Symptom
JL9007 G*board to B*Board Harness
harness Improvement
or or
23pin of CN9000 LD board to B*Board
No improvement
on B*Board

Voltage < 1.8 V Harness /

Connection OK LED driver or G* board Symptom
LD board/G board
 Change LD board or G* board. Improvement

No improvement
Change Symptom
Panel
Panel Improvement

No Improvement
Change Symptom
B* Board
B* board Improvement

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 102

 TROUBLE SHOOTING

3-3-9. 7 Times Blinking (Temperature Error)

7-time blinking

Setting
circumstance is OK? No Set to another
Temperature, location, etc.
Ventilation, etc.

Yes
Change B* Board, NG
and Aging a few Panel
hours

Symptom
improvement
Check I2C_C bus Yes Temp sensor
B* Board NG communication OK?
IC1400
(check the next page)
No

I2C_C bus dumping or

Muffin check

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 103

 TROUBLE SHOOTING

3-4. NO SOUND
3-4-1. No Sound Audio 3-4-2. No Sound : TUNER

No Sound No Sound with normal picture

Audio

Yes NO
Segment “XS”? Only RF tuner input?

YES
No

Replace B-K Harness Yes

Please refer Audio
OK ? Check IC1000 (SOC)
troubleshooting

No

Replace K-PWB Yes

OK ?

No

Replace B-PWB Yes

OK ?

No

Finish

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 104

 TROUBLE SHOOTING

3-4-3. No Sound : MHL

No Sound

NG
Check the picture Refer to 4.6 MHL NO PICTURE

OK

OK
Check Sound by other TV set
Refer to 3.1 No Sound Audio
which is same model

NG

Check Source equipment

OK
by Reference TV set
Change B-Board.
(For example, Samsung TV(UN46ES7000),
Toshiba TV(42WL863), RB1 or RB2)

NG

Check the settings of

Source equipment

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 105

 TROUBLE SHOOTING

3-4-4. No Sound : HDMI1/2/3/4

No Sound

NG
Check the picture Refer to 4.5 HDMI (1/2/3/4) NO PICTURE

OK
Does this model have YES
Check the mode DVI Connect Stereo minijack cable between Source and the TV, and
Analog Audio In
of Source equipment Change “HDMI/DVI Audio Source” to Auto or Analog Audio In.
(Stereo minijack)?
No
HDMI Change the mode of Source equipment to HDMI

Analog Audio In
Does this model have YES “HDMI/DVI Audio Source”
Analog Audio In Change “HDMI/DVI Audio Source” to Auto or HDMI Audio In
setting is?
(Stereo minijack)?
Auto or HDMI Audio
NO

Check Sound by other TV set OK

Refer to 3.1 No Sound Audio
which is same model

NG

Check Source equipment OK

NO
Is Distributor used ? by Reference TV set Change B-Board.
(For example, RB2, RB1)
YES
NG

Connect Source Check the settings of

equipment directly Source equipment

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 106

 TROUBLE SHOOTING

3-5. NO PICUTURE

No Picture BL_ON (L or H): IC9017 #18pin (for 4K BMFW/BMFL board)

BL_ON：H
No Check Smart Core No Check Replace NG NG
Got Any Normal Replace LCD Panel
Behavior BL_ON the V by One FFC
Display? the main Board (T-CON)
(5x Blinking) on the main board Harness

Yes Symptom Symptom

Yes BL_ON：L
improvement improvement

Check Other 5x Blinking Backlight V by One FFC

Main board NG
Portion: Harness

Ext. Video Input -

No Picture

HDMI - No Picture

Tuner - No Picture

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 107

 TROUBLE SHOOTING

3-5-1. No Picture AEP Destination (BMFL/BMFW) SCART

No Picture AEP

SCART RGB SCART CVBS

No Picture No Picture
NG
NG
[LOW: 0V]
[LOW: 0V]
OK NG NG
Check SCART_FB ** Detailed check all parts Check SCART_FB
* Check CN7501 * Check CN7501
IC1000 L37 at SCART_FB signal IC1000 L37
Connection Connection
[SOY0] at R7514 Path [VD7504/R7513] [SOY0] at R7514
OK
OK [HIGH: 0.4V  Composite] NG OK [HIGH: 0.4V  Composite]
OK
OK [HIGH: 3V  RGB] OK [HIGH: 3V  RGB]

NG
** Detailed check all parts
at SCART_FB signal
** Detailed check all parts at Path [VD7504/R7513]
CN7501 along signal path
at Pin No: OK
Check wave between NG (Vpp: 0 V)
7 : [VD7503/R7503/C7501/ Detailed check all parts at
C7502/C7505/C7507 R7504] NG (Vpp: 0 V) CN7501 along signal path NG
and IC1000 11 : [VD7502/R7506/C7503/ NG Check wave between
at Pin No:
R7507] C7511 and IC1000
20 : [D7505/R7518/C7510/
15 : [VD7501/R7510/C7506/ R7599/R7519]
OK (Vpp: 1 V) R7511]
OK (Vpp: 1 V)

OK OK

Muffin [IC1000] CN7501 Connectivity CN7501 Connector Muffin [IC1000] CN7501 Connector CN7501 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 108

 TROUBLE SHOOTING

3-5-2. No Picture AEP Destination (BMFL/BMFW) VIDEO

No Picture AEP

Video 2 Component
No Picture No Picture

NG NG * Check J7504 Con

Check if input OSD
* Check J7504 NG (Vpp: 0 V) Check if input OSD
VIDEO_DET at NG (Vpp: 0 V)
Connection, is GREY OUT
is GREY OUT
VIDEO_DET R7539,
OK if it is highlighted OK if it is highlighted
At R7539 CR_DET at R7538

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V) ** Detailed check all parts

parts at VIDEO_DET at VIDEO_DET signal NG (Vpp: 0 V)
signal Path [R7535] Path [R7535] and CR_DET
signal path [R7534]
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
Check wave between
NG (Vpp: 0 V) ** Detailed check all parts NG Check wave
NG (Vpp: 0 V) Y1P : [D7530/R7524/C7514/
NG
at CVBS3P signal path Between R7527]
C7512 and IC1000
[D7530/R7524/R7525] C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
OK (Vpp: 1 V) OK
OK (Vpp: 1 V) R7553]

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 109

 TROUBLE SHOOTING

3-5-3. No Picture CH/MX/PA/COL/LA (BMFL/BMFW)

No Picture Video

Video 1 Video 2
No Picture No Picture

NG
NG * Check J7505 * Check J7504
Check if input OSD NG (Vpp: 0 V) Check if input OSD NG (Vpp: 0 V)
Connection, Connection,
is GREY OUT is GREY OUT
VIDEO2_DET VIDEO_DET
OK if it is highlighted OK if it is highlighted
At R7562 At R7539

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V)

parts at VIDEO2_DET ** Detailed check all NG (Vpp: 0 V)
Signal Path [R7561] parts at VIDEO_DET
Signal Path [R7535]

OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

NG (Vpp: 0 V) ** Detailed check all parts NG NG (Vpp: 0 V)

Check wave between at CVBS2P signal path
Check wave between ** Detailed check all parts NG
C7511 and IC1000 [D7514/R721/C7521/ at CVBS3P signal path
C7512 and IC1000
R7519/C7534] [D7530/R7524/R7525]

OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK

Muffin [IC1000] J7505 Connector J7505 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 110

 TROUBLE SHOOTING

3-5-4. No Picture CH/MX/PA2/NZ/AUS/BR/COL/BR/UC/HK/TW (BMX)

No Picture Video

Component
No Picture

NG
Check if input OSD * Check J7504 Con NG (Vpp: 0 V)
is GREY OUT VIDEO_DET at R7539,
OK if it is highlighted CR_DET at R7538

OK
OK (Vpp: 3.3 V)

** Detailed check all parts

NG (Vpp: 0 V)
at VIDEO_DET signal
Path [R7535] and CR_DET
signal path [R7534]

OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
Check wave Y1P : [D7530/R7524/C7514/ NG
NG (Vpp: 0 V)
Between R7527]
C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
OK (Vpp: 1 V) R7553]

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity

Problem Parts Broken
Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 111

 TROUBLE SHOOTING

3-5-5. No Picture J/UC/HK/TW Destination (BMFL/BMFW)

No Picture

Video1 Video2
No Picture No Picture

Check if input OSD

NG * Check J7501 NG * Check J7504
NG (Vpp: 0 V) Check if input OSD NG (Vpp: 0 V)
Connection, Connection,
is GREY OUT is GREY OUT
VIDEO2_DET VIDEO_DET
OK if it is highlighted OK if it is highlighted
At R7537 At R7539

OK OK (Vpp: 3.3 V) OK OK (Vpp: 3.3 V)

** Detailed check all NG (Vpp: 0 V)

parts at VIDEO2_DET ** Detailed check all NG (Vpp: 0 V)
Signal Path [R7556] parts at VIDEO_DET
Signal Path [R7535]

OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)

NG (Vpp: 0 V) ** Detailed check all parts NG NG (Vpp: 0 V)

Check wave between at CVBS2P signal path
Check wave between
** Detailed check all parts NG
C7511 and IC1000 [D7505/R7559/ at CVBS3P signal path
C7512 and IC1000
C7511etc] [D7530/R7524/R7525]

OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK

Muffin [IC1000] J7501 Connector J7501 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited
[All voltage measurement using Oscilloscope]

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 112

 TROUBLE SHOOTING

3-5-6. No Picture J/UC/HK/TW Destination (BMFL/BMFW)

No Picture

Component
No Picture

Check if input OSD NG * Check J7504 Con NG (Vpp: 0 V)

is GREY OUT VIDEO_DET at R7539,
OK if it is highlighted CR_DET at R7538

OK
OK (Vpp: 3.3 V)

** Detailed check all parts NG (Vpp: 0 V)

at VIDEO_DET signal
Path [R7535] and CR_DET
signal path [R7534]

OK (Vpp: 3.3 V)

** Detailed check all parts

at signal path of:
Check wave NG (Vpp: 0 V) Y1P : [D7530/R7524/C7514/ NG
Between R7527]
C7515/C7518/C7520 PB1P : [VD7508/R7529/C7517/
and IC1000 R7530]
PR1P : [VD7509/R7532/C7519/
R7553]
OK (Vpp: 1 V)

OK

Muffin [IC1000] J7504 Connector J7504 Connectivity

Problem Parts Broken
Problem Problem

*  OK Condition : No solder splash can be seen **  OK Condition : No part short-circuited

 NG Condition : Solder splash can be seen  NG Condition : Part short-circuited

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 113

 TROUBLE SHOOTING

3-5-7. No Picture : @ Tuner

Notes:
I2C line for all tuners except Japan_SKP
- Parts for I2C_A_SDA line: R6001, C6004.
RF input no picture / noisy picture - Parts for I2C_A_SCL line: R6002, C6005.

I2C line for Japan_SKP

Check RF source cable NG - Parts for I2C_D_SDA line: R6003,C6006
Change RF cable and antenna - Parts for I2C_D_SCL line: R6004,C6007
and antenna, OK?
OK TU_1.1V line only in Japan_SKP Tuner
- Parts for TU_1.1V: FB6800
Check Tuner power line:
3.3V at JL6005 = 3.3V?
1.8V at JL6006 = 1.8V? NG Please refer DDCON
DEM_3.3V at JL6019 = 3.3V? troubleshooting
A_RESET value at JL6012 = 3.3V?
For JP_SK only – TU1.1 V (Refer notes)
OK
Check part mounting condition
YES for “I2C_A_SDA, I2C_A_SCL NG
All broadcasting channel Change NG parts
or
cannot be received? connected to I2C bus
I2C_D_SDA, I2C_D_SCL”
Refer Note I2C
NO
OK

Digital

Satellite

Check Tuner power line NG 12V LNB Voltage

Terrestrial/Cable
Analog 12V at JL6027 = 12V? Checking
OK

For TW & NA-ATSC All tuners except

(MX/UC) only TW & NA-ATSC(MX/UC)

Refer Analog Tuning Refer Digital Tuning 1 Refer Digital Tuning 2

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 114

 TROUBLE SHOOTING

3-5-8. FOR 12V LNB Voltage Checking: @ AEP_W and JP_SKP

12V LNB Voltage Checking

OK OK OK
Check Tuner power line Check P_ON_LNB signal line MOSFET Q9019
Check fuse F6000
12V at JL9012 = 12V? at R9167 = 3.3V? broken

NG NG NG

Please refer DDCON

Change the fuse troubleshooting

NG
Check harness between
Harness broken
B-Board and G-board

OK

Please refer G-board

troubleshooting

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 115

 TROUBLE SHOOTING

3-5-9. FOR ANALOG TUNING: @ All destination except JP

Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327,
C6301, R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326,
C6300, R6300.
For LA-ISDB(BR/AR), LA-T2(COL) and TW only - Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
Analog Tuning
R6303.
For Other destination
NG A : Insert correct signal in correct terminal.
Confirm ANT or Cable connection A

OK

Check part mounting condition for NG

analog control line Change NG parts
“IFOUT_N, IFOUT_P, IFAGC”

OK

Check IC1000(SOC)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 116

 TROUBLE SHOOTING

3-5-10. FOR DIGITAL TUNING 1: @ TW, NA-ATSC(MX/UC), JP_SKP and LA-T2(COL)

Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327, C6301,
R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326, C6300,
Digital Tuning 1 R6300.
- Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
For TW only R6303.
For all
tuners A : Insert correct signal in correct terminal.
NG
except TW
Confirm ANT or Cable connection A

OK
Sound is normal?

Check IC1000 (SoC)

No sound

OK
Check part mounting condition for digital data line
“IFOUT_N, IFOUT_P, IFAGC”

NG

Change NG parts Check SOC(IC1000) and Tuner

module

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 117

 TROUBLE SHOOTING

3-5-11. FOR DIGITAL TUNING 2: @ AEP_W, JP_SKP, PA_T2, CH/HK, LA-ISDB(BR/AR) and LA-T2(COL)

For LA-ISDB(BR) and Digital Tuning 2

LA-T2(COL) only

For AEP-W For JP_SKP

NG For PA_T2 and NG
CH/HK only NG
Confirm ANT or Cable connection A Confirm ANT or Satellite connection A Confirm ANT or Satellite connection A

OK OK OK
Terrestrial All except SKP_Opticast BS/CS or SKP_Opticast/
Digital cable/ Terrestrial
SKP_Premium or terrestrial

Cable OK SKP_Opticast
Sound is normal?

Refer to Digital Tuning 1 No sound Refer to Digital Tuning 1

Check IC1000 (SoC)

On Service Notes:
mode display CASE B - Parts for TU1_TS_DATA0 line: R6015,
TS_LOCK ? R6321.
UEC ? - Parts for TU1_TS_CLK line: R6016, R6322.
- Parts for TU1_TS_VALID line: R6017, R6323.
CASE A - Parts for TU1_TS_SYNC line: R6018, R6324.
Change Tuner module
(Refer to Note tuner ) - CASE A : TS _LOCK = LOCK and UEC
constant
- CASE B : TS _LOCK = UNLOCK or UEC is
OK increasing
Check part mounting condition for digital data line
“TU1_TS_DATA0, TU1_TS_CLK, TU1_TS_VALID, TU1_TS_SYNC”
Note Tuner –
(IC reference -- destination)
TU6001 - PA-T2
NG TU6001 - LA-T2/LA-ISDB
TU6001 - CH, HK
Check IC1000 (SoC)
TU6003 - AEP_W
TU6802 - JP_SKP
Change NG parts
A : Insert correct signal in correct terminal.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 118

 TROUBLE SHOOTING

3-5-12. NO PICTURE: HDMI1

No Picture

If you can do Check the below point at

component repair Connector side All lines
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5202
・Check DDC lines NG
All Inputs are NG ・Check TMDS lines

+5V line is OK Only TMDS

Only +5V line
and HPD line lines
is NG
Check Picture by other TV set is NG are NG
Change B-Board. Spec:4.7~5.3V
which is same model Spec:2.4~5.3
Other TV set V
OK Replace
Target board & other TV set If you can do JC5216, JC5217
both NG component repair Replace RB5209, RB5210
R5515 Only DDC
lines NG
are NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
(HDMI EQ).
No

Check Source equipment Replace IC5212

by Reference TV set Change B-Board. (HDMI EQ).
(For example, RB1) Reference TV Set OK

Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 119

 TROUBLE SHOOTING

3-5-13. NO PICTURE: HDMI2

No Picture

If you can do Check the below point at

component repair Connector side All lines
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5202
NG
・Check DDC lines
All Inputs are ・Check TMDS lines
NG
Only +5V line +5V line is OK
Only TMDS lines
is NG and HPD line
are NG
Check Picture by other TV set Spec:4.7~5.3V is NG
Change B-Board.
which is same model Spec:2.4~5.3
Other TV set
V Replace
OK If you can do
Target board & other TV set component repair JC5208, JC5209
both NG Replace Only DDC RB5211, RB5212
R5517, R5518 lines
are NG NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
(HDMI EQ).
No

Check Source equipment

by Reference TV set Change B-Board. Replace IC5212
(For example, RB1) Reference TV Set OK (HDMI EQ).

Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 120

 TROUBLE SHOOTING

3-5-14. NO PICTURE: HDMI3

No Picture

Check the below point at

If you can do Connector side All lines
Check other Other Input is OK component repair ・Check +5V line are NG Replace
Change B-Board.
HDMI input ・Check HPD line CN5203 NG
・Check DDC lines
All Inputs are ・Check TMDS lines
NG
Only +5V line +5V line is OK Only TMDS lines
is NG and HPD line are NG
Check Picture by other TV set
Change B-Board. Spec:4.7~5.3V is NG
which is same model Other TV Spec:2.4~5.3
set OK V Replace
If you can do JC5237, JC5238
Target board & other TV set component repair
both NG RB5213, RB5214
Replace Only DDC lines NG
R5428 are NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
No (HDMI EQ).

Check Source equipment

by Reference TV set Change B-Board. Replace IC5212
(For example, RB1) Reference TV Set OK (HDMI EQ).

Reference TV
set
NG Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 121

 TROUBLE SHOOTING

3-5-15. NO PICTURE: HDMI4

No Picture

If you can do
Check the below point at
component repair All lines
Connector side
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5208 NG
・Check DDC lines
All Inputs are NG ・Check TMDS lines

Only +5V line +5V line is OK

is NG and HPD line Only TMDS lines
Check Picture by other TV set Spec:4.7~5.3V is NG are NG
Change B-Board.
which is same model Other TV Spec:2.4~5.3
set OK V
If you can do Replace
Target board & other TV set Replace JC5239, JC5240
component repair
both NG R5467 RB5215, RB5216
Only DDC lines
are NG NG
Connect Source
Is Distributor used ?
Yes equipment directly Replace IC5212
No (HDMI EQ).

Check Source equipment

by Reference TV set Change B-Board.
(For example, RB1) Reference TV Set OK Replace IC5212
(HDMI EQ).
Reference TV
set
NG Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 122

 TROUBLE SHOOTING

3-5-16. NO PICTURE: MHL (BMX)

No Picture

Check voltage at
CD_SENSE_0,
High NG (No communications)
R5509 Check HDMI_0_HPD_CBUS
Replace IC5212(HDMI EQ).
Spec:High:2.0~5.3V at connector side
Low:0.8~2.0V
OK
Low NG (No communications)
Check TMDS(D0+/D0-) lines
at connector side
Replace
RB5211
OK
Low (< 2V)

Check DDCCLK,
Check RB5219 (47k ) Check Source equipment
at CL5256
NG (Open) by Reference TV set
High OK (For example, Samsung TV(UN46ES7000),
Replace Toshiba TV(42WL863), RB1, RB2) OK
RB5219

NG

Check HDMI picture

Check D5205, D5206
in this input
Change NG (Open)
MHL cable
OK Replace NG
D5205, D5206

Check the settings of Check “NO PICTURE

Replace IC1000 (SoC).
Source equipment – HDMI” flow

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 123

 TROUBLE SHOOTING

3-5-17. NO CHARGE: MHL (BMX)

No Charge

STBY “MHL Charge During STBY” Off

The TV Power Status? Change “MHL Charge During STBY” (UI) to “On”
(UI) Status?

TV On

5V
CN5202 #18 pin Change MHL Cable

0V
High 0V
Check voltage at 0V
Check IC5208 #6 Check IC5208 #3
CD_SENSE_0, Replace IC1000 (SoC).
(VBUS IC, Out) (VBUS IC, EN)
R5509
Low (< 2V) 5V

Low (< 2V) Replace IC5208 (VBUS IC)

Check DDCCLK, NG (Open)
Check RB5219 (47k )
at CL5256

High Replace
OK
RB5219

Change
MHL cable Check D5205, D5206 NG (Open)

Replace
OK
D5205, D5206

Replace IC1000 (SoC).

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 124

 TROUBLE SHOOTING

3-6. SIDE BUTTONS MALFUNCTION

Side Key button OK

Change Switch Unit Switch unit issue
malfunction

NG

Harness on Switch Unit OK Harness

and B* Board properly connected connection
issue
NG

Change OK
Switch unit-B* board Harness Harness issue

NG
NG
Power Key (B*Board) NG Key AD(B*Board)
NG Check parts value :
Check parts value : Parts Broken issue
0 ohm < R1089 < 2 ohm 0 ohm < R1091 < 2 ohm
4.4k ohm < R1432 < 5k ohm 0 ohm < R1042 < 2 ohm
OK OK

Power Key Muffin Pin (B*Board) OK OK Key AD muffin pin (B*Board)

Muffin IC1000 Check voltage (Power ON condition):
Check voltage(Power ON condition) :
3.13V < Voltage < 3.47V problem 1.62V < voltage < 1.84V

NG NG

Change B*Board

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 125

 TROUBLE SHOOTING

3-7. IR REMOTE COMMANDER MALFUNCTION

Check whether center Remote control battery

Center white LED OK OK
IR do not response to white LED blink ,when using
lit up when remote could be weak.
Remote Commander commander near the sensor
control is pressed windows Change battery.

NG
Harness on H-board OK Harness
and B* Board connection
properly connected issue
NG

Change OK H-B* board harness

H-B* board Harness issue

NG

OK
Change Smart Core Smart core issue

NG
B*Board
NG
Check parts value : Parts Broken issue
R1080 = zero ohm
OK

SIRCS (IC1000 Pin Y35 , B*Board) OK Muffin IC1000

Check voltage (Power ON condition):
3.287V < Voltage < 3.55V? problem

NG

Change B*Board

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 126

 TROUBLE SHOOTING

3-8. LIGHT SENSOR ERROR

Backlight doesn’t change OK

Check UI setting for light Change the UI setting User did not activate light
when ambient lighting Sensor. Make sure it is “on”
level changed
to “ON” sensor function
NG

Harness on H-board and OK Harness connection

B* Board properly connected issue

NG
OK H-B* board harness
Change
H-B* board Harness issue

NG
OK
Change Smart Core Smart Core issue

NG
B*Board NG
Check LIGTH_SENSOR signal path : Part broken issue
R1079 = zero ohm
OK
LIGTH_SENSOR (Muffin Pin L35) OK
Check voltage variation from Muffin IC1000 problem
room light to dark condition
NG

Change B*Board

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 127

 TROUBLE SHOOTING

3-9. NETWORK MALFUNCTION

1) Ethernet (Wired)

[Network Set-up]
>[Wired Set-up]
on the TV

OK OK OK
Connection Results Connection Results Connection Results
Cable Connection Local Access Internet Access
B board

Failed Failed Failed

OK Auto
Check Proxy setting
Check cable B board Wired Set-up
Local router
IP address setting
DHCP server

NG Manual

Ethernet Cable Check IP address

&
Local router setting

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 128

 TROUBLE SHOOTING

2) Internal Wireless Network malfunction

Wireless Network
on the TV

Error Message appear No Is the radio field No

when the Wireless Strength too weak Bxx Board
Network is selected? or even No signal?

Yes Yes
NG
Change WiFi module Access Point
From previous page
OK

WiFi module

Check harness
NG OK
connection is OK Connect properly Loose harness
between WiFi and Bxx

OK NG
Change harness
Change NG NG
between Bxx board Change Bxx board
Wi-Fi module
and WiFi
OK If Wi-Fi malfunction happens,
OK
• Wi-Fi module
• Harness between WiFi
Wi-Fi module Main Harness and Bxx
• Bxx board
are suspected.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 129

 TROUBLE SHOOTING

3) Bluetooth malfunction

Touch pad Remote doesn’t work

Or
3D-glasses (Active) doesn’t work
Or
Bluetooth Speaker/Headphone/Headset doesn’t work

Please refer
OK Touch pad Remote manual
Home > Settings > Check BT antenna OK 3D-glasses (Active) manual
Bluetooth Settings Connection is OK
Can read Or
Near discoverable
Bluetooth Device Bluetooth Speaker/Headphone/Headset operation manual
NG NG
else

OK Loose BT antenna
Connect properly connection
NG

Check harness NG OK
connection is OK Connect properly Loose harness
between BT and Bxx

OK
NG

NG Change harness NG
Change BT module Between Bxx board Change Bxx board
and BT
OK OK

BT module Main Harness

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 130

SEC 4. DIAGRAMS
4-1. BLOCK DIAGRAM

Ether

Tuner
I2C
(Audio)
TEMP IC card
Sens LOG
or

eMM LOG
C I2C(panel)
ECS
HDMI1 Vx1 x16

HDMI2 HDMI EQ
DDR3
/MHL 2Gb
LD
Vx1 x8 LD
AV2/Component Main SoC Vx1 x4 Soc
HDMI3
I2C(Backlight,Panel)
4k SoC I2C(Backlight)
UART(4KBE
AV1(SCART) Communication) I2C
HDMI4 (Audio) Audio
AMP
Audio
Audio AMP
AMP

Audio
AMP
Audio
AMP

HP/Line out
Audio
Opt.Out AMP
Audio
AMP

USB3.0 USB2.0 USB2.0 WIFI/BT

SmarCore Key-pad

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 131

 (Only Interface between board and board）

SM (FY14) BAX_F Board

BMFW Board CN3601 To BMFW
CN203 GND 1 51 GND T-con Board
1-798-511-11(ALPS)/ HUS_GND 1 19 VBTX7P 2 50 RxP7
1-798-510-12(NOBLE) HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 PANEL FFC
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
5 5 WIFI_GND VBTX2P 17 35 RxP2
6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
9 9 WIFI_GND VBTX1N 21 31 RxN1
10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
11 12 BT_3D_LR VBTX0N 24 28 RxN0
13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 AGP/NSB (High/Open:AGP, Low: NSB)
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 NC
1 19 CAM_GND BITSEL 31 21 NC(BITSEL(High/Open:10Bit; L:8Bit))
CN001 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 nWP(High:Write; L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 PCID_EN (High: Enable, Low/Open: Disable)
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 NC
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 NC
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 NC
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 NC
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 NC
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 NC
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 NC
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 NC
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 NC
NC 39 HUS_GND NC(ABL_HOT0)/12V 51 1 NC
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
WOBT_L 4 4 CN3600 To BMFW
GND 5 5 NC/HTPDN1/ELTIMO3/POWER_ON 1 41 NC
VCC 6 6 CN8004 NC/LOCKN1/ABL_PHT/READY 2 40 NC
VCC 7 7 3 BLK#28 1 CAMERA_5V NC/SDA/PANEL_ERROR/PANEL ON 3 39 NC
VCC 8 8 3 RED#28 2 CAMERA_USB_M NC/SCL/PANEL ERROR 4 38 NC
GND 9 9 3 CAMERA_USB_P SPI_CS 5 VbyOne-FFC 37 NC
GND 10 10 4 ID (GND/CLK/CAM_POP) : Connect GND via R=0 Ohm SPI_CK 6 36 NC
VSYNC 11 12 5 GND_S NC/RESETX 7 35 NC
GND 12 11 3 Shield 1-822-265-21 GND 8 34 NC
GND 13 13 ACON Mini-USB NC 9 33 NC
DM 14 14 3 WHT#28 NC 10 32 NC
4-2. CONNECTOR DIAGRAM

DP 15 16 3 GRN#28 NC 11 31 NC
1-819-332-11 1-819-502-11 VCA/(SPI_SEL0) 12 30 NC
JST SM15B-GHS-TB(LF)(SN)
GHR-15V-S CN9000 BUS_SW 13 41pin FFC 29 NC
NC 30 DIGITAL_STBY SPI_DI/(WDT) 14 28 NC
2 29 DC_DIMMER SPI_DO 15 27 HTPDN (LGD Use Only)
3 28 BL_ON/ICSPCLK SPI_ENB 16 26 LOCKN (LGD Use Only)
4 27 PWM_DIMMER GND 17 25 GND
BT 5 26 STBY_3.3V VBTX15P 18 24 RxP15
6 25 BLINKING VBTX15N 19 23 RxN15
Antena 7 24 AC_OFF_DET GND 20 22 GND
8 23 BL_ERR VBTX14P 21 21 RxP14
9 22 POWER_ON/ICSPDAT VBTX14N 22 20 RxN14
10 21 GND GND 23 19 GND
11 20 GND VBTX13P 24 18 RxP13 J110
12 19 GND VBTX13N 25 17 RxN13 GND Ground 1 21 AWG#22
13 18 REG12V_Audio GND 26 16 GND GND Ground 2 23 AWG#22
14 17 REG12V VBTX12P 27 15 RxP12 PWR Power V12 IN 3 NC
15 16 REG12V_Audio VBTX12N 28 14 RxN12 PWR Power V12 IN 4 25 AWG#22
16 15 REG12V GND 29 13 GND PWR Power V12 IN 5 27 AWG#22
NC 14 REG12V_Audio VBTX11P 30 12 RxP11 1-822-322-11 1-820-264-11
18 13 REG12V VBTX11N 31 11 RxN11 JST SM05B-PASS-TBT(LF)(SN) PAP-05V-S
NC 12 GND GND 32 10 GND

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C

20 11 GND VBTX10P 33 9 RxP10
NC 10 TCON_GND/VPP_PIC VBTX10N 34 8 RxN10
22 9 GND GND 35 7 GND
NC 8 TCON_GND VBTX9P 36 6 RxP9
24 7 TCON_ON VBTX9N 37 5 RxN9
NC 6 TCON_VCC12V GND 38 4 GND
26 5 TCON_VCC12V VBTX8P 39 3 RxP8
NC 4 TCON_VCC12V VBTX8N 40 2 RxN8
NC 3 TCON_VCC12V GND 41 1 GND
NC 2 GND 1-843-699-11 1-819-564-11
NC 1 GND FFC Direct Connector :IPEX JAE/FI-RE41S-HF
1-843-925-11 1-843-917-11 or Yamaichi 1-843-708-XX
PBDP-30V-S JST SM30B-PBDSS-TF
CN8301
TM_SCL 1
TM_SDA 2
GND 3
TM_SPI1_SCK 4
TM_SPI1_MOSI 5
TM_SPI1_nSS 6
GND 7
TM_EMIT 8
BL_TYPE 9
TM_SPI0_SCK 10
TM_SPI0_MOSI 11
TM_SPI0_nSS 12
GND 13
TM_SPI_SYNC 14
TM_MODE0 15
TM_MODE1 16
TM_RDY 17
TM_LOG_RX 18
TM_LOG_TX 19
SA_MODE 20
VLEDPWM1 21
VLEDPWM0 22
CN7706 Reserve 23
1 GND_D BL_ON 24
2 +5.0V_AUDIO 0-336-971-01
3 GND_D FFC 24pin IRISO
4 X_SYSTEM_RST or Hirose FH52-24S-0.5SH
5 X_DAMP_MUTE
6 X_AMP_ERR_DET
7 X_DAMP_RESET
8 I2C_C_SCL
9 I2C_C_SDA
10 DC_OFF_DET
SPEAKER L+ 1 4 11 DAUOA_DAT3
Front L- 2 3 12 DAUOA_DAT2
Lch JST SMP-02VF-N 13 DAUOA_DAT1
1-784-991-21 14 DAUOA_DAT0
15 DAUOA_LRCK
16 GND_D
SPEAKER R+ 1 1 17 DAUOA_BCK
Front R- 2 2 18 GND_D
Rch JST SMP-02VF-N 19 DAUOA_MCK
1-784-991-21 20 GND_D
1-819-407-71
IMSA-9637S-40-Y801
or Hirose FH52-20S-0.5SH

GL4 Board

CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 24
BL_ERR 8 23 CN7700
POWER_ON 9 22 #24 1 1 SP_MAIN_RP
GND 10 21 #22 #24 2 2 SP_MAIN_RN
GND 11 20 #22 #24 2 3 SP_MAIN_LN
GND 12 19 #22 #24 1 4 SP_MAIN_LP
REG12V 13 18 #22 1-842-593-11 1-842-566-12
REG12V 14 17 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11

CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21

CN6801
1-822-359-11
53426-0410
+OUT1 1
NC 2 To LS
+OUT2 3
NC 4
1-822-326-11
51103-0400
CN6802
1-843-363-11
53426-0810 Molex
-OUT1-1 1
-OUT1-2 2 To LS
-OUT1-3 3
-OUT2-1 4
-OUT2-2 5
-OUT2-3 6
NC 7
NC 8
1-822-330-11
51103-0800
DIAGRAMS

132
 DIAGRAMS

4-3. PC BOARD DIAGRAM

BMFW (A SIDE)

qmPNMV
Å~ã V Å~ã MNP Å~ã R
` TTQS ` TTQT ` TTQU ` TTQV ` kTTMS ` kPSMN ` kPSMM ` kUPMN
` kNMMM Å~ã MNN
Å~ã UMQ ` PNRO
` kTTMQ
` kTTMR` kTTMM nVMOT ` kVMMM
Å~ã MOR Å~ã PV f ` PNMP
Å~ã MVT Å~ã VMQ ` i PSOT ` i PSOP
` i PSOR ` i PSNU
` i PSOM
` i PSON ` i PSNS
` i PSNT ` i PSNR
` i PSNQ
` NMSU ` i NM
`iMUMT
NM
` TUTU Å~ã MPQ ` i NMMS a VMMOnVMOU
oVMVP oPSRP
` i PSPN
` i PSPP ` i PSOU ` i PSOQ
` i PSOS ` i PSRV
` i PSOO ` i PSNV ` i UPMV
Å~ã MNO i TTMQ i TTMR i TTMS i TTMT ` TTSS` TTSR ` NMST ` i PSQM ` i PSPS ` i PSPO
` i PSPU ` i PSPM g` PSMT g` PSMS g` PSMR g` PSMQ g` PSMP g` PSMO g` PSMN g` PSMM ` PSUR` PSUQ
o_NMMM` i NMMP oNMVN s a NMMM oNMUM ` NMSO oPPPNoPPPO
oPPPMoPPPP
oPPPS
oTVUM ` NM`TN
NMTO` NMSQ` NMTP ` NMTR` NMTU ` NMTV ` PSUP ` PSUO
oPSOT
oTVPM oTVON
qmPNNN oNNMV oPSRO ` i PSQN
` i PSQO
` i PSQP ` i PSPT
` i PSPV ` i PSPR ` i PSOV ` PSVO ` PSUU
` PSVP ` PSUT
` PSUS
oPSPM oPSTO
oTVOT oTVOM oNMTR oNMUU oNMTV ` NMSN oNMSO oPSUR
oPSUQ oPSTV ` i PSRQ Å~ã MOQ
s a NMMN Å~ã OS OMoVM
oVNUU `ON ` UPSN
` UPSO
UPRR ` UPRQ ` UPRO
` UPRP ` UPQV
` UPRM
` UPRN ` UPQS
` UPQT
` UPQU ` UPQR` UPQP
` UPQQ ` UPQN
` UPQO ` UPPV
` UPQM
oTVPN
oTVTU ` NMTM` i NMMQ ` NMSR oNMUOoNMURoNNMT
nVMOV nVMPM oPSVR
oPSVQ ` PTMN
oPSVP
NoPSPS oPSTQ
R oPSTR oPSPN
oPSTP oPSPO
oPSOV oPSPP
oPSOU oPSPQ
oPSTNoPSTM ` VM
oPPOT
oPPOS oPPOV
oPPOU
Å~ã MPO ` TUSR ` i NMMR a NMMP
` NMRT oNM
`TP
NMUO
oPTNS
` PTMQ oPSVN` PTM M` PSVU
` PSVV ` PTNP
oPTM Q` PTNO
oPTM P` PSVQ
oPTM OoPSUM
oPTM oPSPR
oPTM
f oj MMN
` TTUO ` TTUN` TTUM ` TTTV` TTOM ` TTNV` TTNU ` TTMV oTVOS` TUTT oNNOU oNMVM ` i PSNM ` VMNT ` VM NU ` VNNV ` VMNN
NRoVNUN
oVM ` VMMV ` VMOT
oVMoVM
OToVM MQoVM
OSoVM OR OQ
oTVOP
oTVOO oNQRM
oNNOToNM oNM
TS TT` NMSS oNMTU ` NMRSoNMUV ` PSVT
` PSVS` PSVR ` i PSSM
` i PSRR oVM`OP
oVMOO VMoUPRV
NS oUPVU oUPRU
oUPVT oUPRS
oUPRT oUPRR
oUPRQ oUPRO
oUPRP oUPRN
oUPRM
oUPVP oUPQU
oUPQV oUPQT
oUPQS
oUPQR
oUPQQ
` NMTT `oPPPQ
j PNMO
` TTRO ` TTRP ` TTRM ` TTRN ` NMTQ ` NMTS oNMUQ oPSQR` PTM OoPSQO
oPSQN oPSVMoPSUVoPSUU oVMOU
oNNMRoNNMS s a NMMO oVMVO ` VMPM i VMMM oVNQQ `oUPUO
j UPMM `oPPPR
j PNMP
` NMUP oNM UT US
oNM oNMUN oPSUP
oPSUT oPSUO
` NMRR oNMUP oPSVOoPSQT ` i PSM `Vi PSM
` i PSM U T oVOMU ` VM
`OS
VM`OR
VM`NP
VM`OP
VM`ON
VMNU
oNNOV oNNOSoNNMU ` i PSNO ` i PSNN ` i PSM S
oPSUS
a NMMO oPSQMoPSPVoPSPU nVMOM ` VNRN
` TTQR a NMMN oPSQQoPSQP oPSQS nVMONoVONS oVNUS
oVNUT oVNUO ` kUMMQ
h^MMN oPSPT oVONR
oVONQoVONO
oVONP oVOMV
oVONN f ` VMNU ` UMPP
oPSOS oPSOR oPSQV oPSQU oVNUR
` VNNU f ` UMMP ` TUMOR` UM
`QN
UM`OQ
UMOP
a PSM
aNPSMM s OU
oUM a UMM
` TTQO ` TTQP oVNUPnVMNR nVMNS
` TTNQ ` TTNR ` TTNS oVNSS
oVNSUoVNVQ i VQMP oVNUQ ` UMOT
` TTQQ oVNRQ pPSMO Å~ã UMS Å~ã UMO
` TTNT ` VNNToVNRSoVNTUoVNUM
Å~ã ONT nPSMN nPSMM Å~ã UMN
oVNRR oPSRN
oPSRM c VQMS ` VQQM ` UMOSÅ~ã UMP oUMPM
oVNTV oVNSP
` VQQP ` VQQO f ` UMMQ
` TUTP ` TUTQ oPTNQoPTNR nVMNT oUMOV
oTVPO oVNRT ` VQRM
oVONM oVNSQ ` VQQN
` TTPN oTTSS i TTMM ` TTMP ` TTMN oVNTT ` VQQQ oVQQT
i TTMN oTVPP ` i UM
` iMN MO
UM
oTVPQ f ` VMNT oVNSR oUPQN oVQQU
i TTMO i TTMP ` VQQR
oVNRU
oVNST
oVNSV oUPVQ
oUPVR f ` VQMS g` UMMO
oTVPR oVMSS
qmPNMS oVNTS oVMSR oVM
f ` TTMM oTVPS ` VMSO oVMSO oVM
SQ RN
Å~ã NTV ` UPPT
` UPPR ` UPPO
` UPPS
c VMMR c VMMM oUPQP
oVNSN oVMSM oVNOV` VMSV
oVNTM ` VNOS
oVNTRoVNRV
oVNTP ` i PSRU Å~ã MVN bqMPR
` TTOU oVNSO
oVNTO ` VMTM ` VQQU ` VQOM` VQMV
` VQON oUPPS
` TTOV ` i RPMO oVNTQ nVMOO ` VMSU i VMMN oUPPU oUPQM` UPPU
oUPPT ` UPPP
oUPVS ` UPOT
` UPOO
` TTOT oVMVM ` VNOT ` i UTNT oVQQRoVQQQ` VQPV
nVMOP f ` VMMU
` TTPM ` VMQT ` VMQU ` VMQV ` VMRM
` VNOV ` VNOU Å~ã MUT oVQQP ` VQQT
` i UTNS oUPPP oUPPV
` TUTR ` TUTS oVQNP oUPUT
oUPUU oUPOP oUPOU qmPNMU
` TTNN oTTRU oVMVN
oVNRP ` VMRN ` VMSR bqMPS oUPPQ
Å~ã MRU oTTRM
oTVST oTTRO
oTTRN c TTMM oVNTN f ` VMMP oVQNO i VQMN ` VQQS
oVQQO
` TTMU ` TTMS oNNTP Å~ã MPR ` i UTNR` UPPQ
` TTQN oTTST ` UPSM f ` VQMN f c j MMO oUPPR
` TUSP ` TTMQ oVQMV ` i PSRS` i PSRT
oTTQU
oTTSM oTTSN oTTQV c TTMO Å~ã MNV
oUPVV ` NMPT` NMPR ` VNPP
oTTOU oVMPQ oVQNM
` TTMM ` TTMO oNMMT oNMMS ` VMUU` VMUS` VMUR` VMUN` VMTR
` VNNS oVNVU
oVNVT ` i PSMR
oPSNP
` UPMT
` UPNT
` TTMT
` TTNM oNMPU oNMPT oVOM
` VNOO ` VNOQ` VNPM
N` VNOP
oVNVV oVMPR oVQNN
` VQNV
oVQMU ` VQNM
f c j MMP ` PNQO oPNSU` i PNNO
f ` TTMN ` NQOU
` NQOR ` UPRV oNMPV ` VQRN oVQON oPNRV ` PSRQ
` PSRP ` PSRM ` PSQR` PSQO
` PSQV` PSQS ` PSPP ` PSPM
` PSPT ` PSPQ
` PSQN` PSPU ` PSOV` PSOS
` PSOR
oPSMN
` UPRU
` NQNR ` PNQR oPNTP c i VQMMoVQRM
` j VQMM oUPNU
oVQQV
Å~ã NMP i VMMQ oVOMM
Å~ã RTU ` VNPN oVMPT oUPMU` UPM U` UPM
` UPNM P` UPM
` UPM Q N
h^MMP Å~ã MVR ` NMPV ` VQNN ` VQNQ ` PNQSoPNTQ ` PNNV oPNOP
oNQOV
oNQPP` NQNN ` i ROOM
oRQUS
oNNQO oVQOM
` PNNMoPNON ` PSRS
` PSRR` PSRO
` PSRN` PSQU ` PSQP ` PSQM
` PSQT ` PSQQ ` PSPR` PSPO
` PSPV ` PSPS ` PSPN ` PSOU
` PSOT ` PSMN ` oPM
j PMM
MQ
N
oNRMP ` NM QN
oNNOO oVMUQ
oVMUR
oVMUS oVMUU
oVMUT oVMUV oPPNQ oPNVV oPNSM
oUTMN ` VNPO ` j VMMS ` VQNR oVQNV ` PNNOoPNNO oPSMMoPNTT ` i PMMP
oTTRT
` NQPP
oNMQM ` NM oNNNN
OS ` VQNO ` PNNT oPNNP ` UPMO
` PQMN` UPNO oUPMVoUPM
oUPNNoUPM
QoUPM
R O
Å~ã MRV oUPTV
oNQPO oUPUM ` NMMN oNMNR
oUPVO oVQNU ` PNMUoPNNN `oUPUS
j UPMS
oUPUR
oNQSM ` PMPM
` TTNP oTTRV ` VQNS ` PNOO ` PNNQoPNOO o_PQNO o_PQNN
Å~ã NMM Å~ã MMP oTTRR
oTTOVoTTRS oNQOT oNMNV oNMNS ` NMPM ` VQNP oVQNT oVQPQ oPSMO` i PSMN ` i PSMM ` PNOP ` POMNoUPNP
oUPM P ` UPM
` UPOQ V` UPM
` UPNN S M` UPOP
R` UPM
` UPM oUPOQ
` TTNO oNQMN oNQMM oPNRUoPNOQ oVQPT ` VQPR
` NMPQ ` PMOT
oTTSP ` TTMR ` NQNQ` NQMM oVMOV oVMPV ` VMQS ` VMQR ` VQNT oVQNS f ` VQMQ
` TUSQoTTRP
oTTSQoTTRQ ` NQNS ` NQNV oNMNToNNMO oPSMP o_PQNM o_PQMV o_PQMU
` NQNT oVMQR ` VQPP ` i PSMO
oTVSU oNQOM oNRMM oNQVVoNQPU ` NMMQ oNMNU oVMPM oVMPUÅ~ã MTV Å~ã MUV oUPNMoUPM
oUPNOoUPM ToUPM
SoUPM M
NoUPUV
oNQOR ` NQMT oNMON ` NMMM ` VQNU oVQNR ` VQPQ oVQPR ` i UPOPoUPOR o_PQMR o_PQMQ
oNQNV oNQPV oNNNU oVMQP f ` VMMQ oVMQS oUPUP ` PSRT oPQMP
oNRMS ` NMMO oVQNQ oPNUM ` i PSMP ` i UPOQ ` i UPNV
Å~ã NMN oNM OM c VQMN ` PNRM oVQPS
oNQPQ `oUPUQoUPVN nUPMN
j UPMN nUPMM ` i UPOO ` i UPOM
` i UPNT
oNNPM oUPTU oVMQQ oUPVM o_PQMP o_PQMO o_PQMN
oNNPN ` UPRT ` PMMN ` PMMR ` i UPON ` i UPNN ` PQQR
` PQQU` PQQV` PQQT` PQQS oPQM VoPQNN
` PQRU oPQNM
` PQRT ` PQQQ
oOMNSoOMNOoOMNR Å~ã MVU ` NM `NT
NQOQ
` NQNM uPSMM
` NQQN ` NMON oPMMR ` PSMP ` i UPNR ` i UPNM
` i UPNS
oNMQR ` NMOV ` PMMS ` PMMQ
` PMOU ` i PMMQ ` PSRU ` i UPNQ
oUTMP oUTM
oUTON Q
oUTOO ` TTVRoTTQNoTTQM ` PMMM ` PMOO ` PSNQ ` PSMO` PSMT ` PSNT
Å~ã NMO o_PQMM o_PQMT
` NMNP oNQNT
oNMQOoNQON ` TUMNoTTUVoTTUU ` PMNN ` PSNO ` PSNS` PSMR ` PSOM oPSNN oPSOM
f ` NQMM oOMMQ oNMQP` NQMS a UTMM a UTMN ` PMNS ` PMNU oPSNR ` PQQP
` PTNQ
` OMMN oPTNN
` TTVSoTTQPoTTQO c i PMMM ` i PMMM ` PMMT ` PMNT ` PMOR ` PSMS ` PSNV` PSMQ ` PSOQ oPSNT
Å~ã NTU ` OMNU oUPTT oPTNM ` TUMOoTTVNoTTVM ` PMNO ` PMON ` PMOS ` PRMU
f ` OMMO oNMQN ` NQOS ` NMOQ ` PSMU ` PSNM ` PSNR ` PSMV ` PQRM o_PQMS
` OMNS oOM
` OMNR MP oNQOO ` NQM Q O
` NQM oNQNOoNQSR f ` PSMM ` POMO ` POMT
oNNNT ` UPRS oPTMS oPTMT ` TUMMoTTUToTTUS ` PMOV ` PMOP ` PSOP` PSNP ` PSNN
` OMON oNQNPoNQSQ oNQSP oNMPQ ` POMR ` POMP
`oPTM
j PSMVN `oPTM
j PSMUM ` TTVQoTTPVoTTPU ` PSOO` PNOR
oOMMR oOMNP o_OMMN o_OMMP ` NMOM ` PMPN f ` PQMN
Å~ã MQS ` OMNV ` NQMU` NQPS oNQSO oNNNS oPTNP oPTNO oTTOT ` PMPQ ` PMPS ` PQMO ` POMQ
Å~ã MUR
f ` OMMN oNQNS
oNQOP
oNQOQ oNMPP Å~ã ONP ` TTVVoTTURoTTUQ oTURR ` PMPO ` PSNU` PNOT
` NQNO` NQPQ
oUTMO
` i TTNQ ` PMPP ` PMPR ` PMOM
` PQMP ` PQMT
` OMOOoOMNT ` NMNS oPSVS ` TTVPoTTPToTTPS ` PMMO ` PMMU ` PQMQ ` POMS
` kNQMP ` NQPO
` NQPM oNMPO oPSOO pPSMM oTURQ
` i TTNP ` i PQNQ
oPSNU ` TTVNoTTPPoTTPO ` TTVT c i PMMN ` PMNM ` PMNR ` i PQMT
o_OMMO o_OMMQ oNQQR
oNQQQ oNQRP
oNQRQ oNNNR oTTOS ` PMMP ` PQMR
oNMSP ` TTVUoTTUPoTTUO ` PSMM ` i PQNO
oNQQT
oNQQS oOMMVoOMMN Å~ã ONO Å~ã ONN oNQRN
oNQRO oPSMT oTTQRoTTQQ ` PMMV ` PQMS ` i UPNO
oNRNP oPSNQ ` TTVOoTTPRoTTPQ ` PSON ` i UPNP Å~ã MSN
Å~ã MUP Å~ã ONU ` i NMMO oPSMQ
oNNPS f ` NQMToNRNOf ` NQMS oTTPNoTTPM ` i TTSN ` i PQNR
oNNOR oPSOP pPSMN oPSVT oPSMV
`NO
` OMOM`NN
OM`NM
OMM`VOMNP` OMNQ
oOMNM ` TUTV ` i TTSM
Å~ã MOM ` NMQP oPSNVoPSMU ` PMSO ` PMSP ` PQRS` PQRR` PQRQ ` PQRV ` PQRO` PQRN
oNMPM ` PQRP oPQNP
` NQSOoNRNR oNRNQ oNRNS oUTNP oPSNSoPSMR ` i TTRV
oNNPT oNRNM oPQNO
` OMMOoOMMO ` OMOM` OMNT oNNNP
` NMMV oOQMP ` OSRR c i OSMO` OSRV c i OSMP ` OSRQ oPSMS ` i UTNQ ` i TTRU
` NMNO ` PQSM
oNMPN pUTMM ` i UTNP ` i TTRT
oOQMQ
oNNPU ` kNQMM oNMRQ ` OOOP ` i UTMO ` i TTRS ` PSUM
oNNNQ ` PQPN` PQOV` PQOU
` PQPM ` PQQM
oPQM
` PQOT QoPQM` SPQPV
oPQM`RPQOS
oNMRP c i OSMN oTURS ` i TTNR oUTNS
` OSSR ` i TTOO
oTUSP oUTOM ` PM`ST
PMSU ` PSTV
` OQOU
` OQOS ` OQPQ oUTNQ ` i UTNO oTUSN ` i TTOM ` UTQQ
` UTQP
` UTQO
` UTPV
oNNPV ` OSQM` OSPU
` OQMT ` PM`SS
PMSV
` OQNN pPNMT oUTOQ oUTNR ` i UTMP ` i TTON
oTUSO ` i UTNU
`OU
` NMNMPO ` OSPR oOQNQ ` OQMN ` OSPT oOQMO ` OSPV oTUSM ` i TTNV
oUTMR oUTMS oTURV
` i TTNU ` UTMU ` i PQMP
` i UTMQ oTURU ` i TTNT ` PQOR
oNNQM ` NQSN ` NMNV oNM oOQMV oOQMT oPPMV oTURT
` i TTNS ` UTMV ` UTQR
` UTPU ` UTPO
` UTPQ
` UTPS ` UTPP ` PM QQ
` PM ` PT
` PM
PU PM
` QP
PM` TM
PSSN
` PSSO
` PSSP` PSSR
` PSSQ` PSSS `RP
POSN
oNQQV
oNQQU oNMPR PS ` OQMS oPPNOoPPNP ` UTNM ` PMRV ` PM
` RS
PM ` i PQNP
oNMOS oNNNO oOQMR oUTMT oUTMU ` i UTMR oPPMU ` QS
` PM PM ` QT
QN
` PM PM
` QO
PM
` QM
PM QRPV
` PM ` PSTU
` PSTS ` PSTT
` PSTN ` PSTO
` PSTP ` PSSV ` POSS
` PSTM ` i PQMS
` PQPO
` UTNN ` PMRT
` kTTMP ` l j NMM ` OQOT
oOQNM ` OQMU oOQMS oUTMV oUTNM` i UTMM ` i TTSO ` UTNO ` PMRU
oNNQN ` OQMO ` TUPS
oTTOR ` POSP
oNRNT Å~ã PU ` OQMR ` OQOQ oUTNN oUTNO ` UTNP ` POSQ oPQM NoPQM
` PQOO M
` PQON f ` PQMM
nNQMO oOMNQ oPPNN oPPNM oTTOQ ` UTNQ ` POSR ` i PQNN
` TTSQ oOQNO ` OSMP ` OSSP
` UTNR
` NQSP ` NMMS ` OQNR ` OOOQ c i OSMR
` OSSO ` UTNS ` POTN ` i PQMO
oOQM`UOQOR ` UTQT ` i PQMV
Å~ã MQP ` kUMMP Å~ã MQV ` UTNT ` UTQU
` UTQV
` UTRM
oNMOO ` OSNM ` UTNU ` PQTR
f ` NQMU nNQMN ` NMNN ` UTRS ` POTR ` i PQMN ` i PQMU
gTTMN ` OSSQ oOQNN ` OQMP Å~ã MPU ` UTNV ` POTS ` PQTQ
qUMMN qUMMM qUMMO oNNNV
oNMOQ ` UTOM ` UTRR f ` PMMM ` i PQMR
` OQPM ` POTT` PQSU ` i PQMQ Å~ã MSM
` OSMS f ` OQMN ` OQMV f ` OQMM ` UTON ` UTRQ ` PQTS ` i PQNM
oNRNUnNQMM oNNON ` UTOO ` UTRP
` UTRO
` UTRN ` POTU
Å~ã MPP ` OQOV
` OSMT ` POTQ ` PQPU` PQPT` PQPS ` PQQN ` PQPQ` PQPP
c i OSMM oOQMM bqMPN ` UTOP ` PMRN ` PQTT ` PQPR oPQMU
` OSMQ ` OQNO ` UTOQ ` PQTV` PQSV ` i PQMMoPQMO oPQMT
` TUSO
oTVSSoTVSQ s oTTMN
` TUSM ` PMRQ ` PMTP
` UTOR ` PQQO
oOQNP ` OSNT ` OSRP ` PMRO
` TURU oTVSN ` NMNR ` OQNP ` OQMM ` OQMQ
` UTOS
` PMRR
` PMSN
` UMNT ` OQNM ` UTOT ` PMSM
Å~ã OMO oUMPV ` UTOU ` POST
` UMNR ` UMNS oNMOR ` OQNQ ` PM
` UTPT
` UTPR `NV
PM `NQ
PMNP ` PM QVRM
` PM ` PM`QU ` PQUN
PQUM ` POTV
` PQUP
` PQUO ` PQTU` PNQT` POTM
` TUSN
oTVSR ` TURV
oTVSP s oTTMM o_UMMQ bqMPO g` UTMQ g` UTMO g` UTMM` i OOMN ` UTOV ` PQTP ` POSU
` NQMV ` OSRU ` UTPM ` PQTO` PQSO` PQSP
` PQTN
` POUP ` PQSR
` POUO `
` POUMPOUN` PQSS
` PQSN
` `
PQTM` POTO
PQSQ
Å~ã MRM c i OSMQ ` UTPN
` TURT oTVRV Å~ã MON ` NQNP ` VUMT ` POTP
` POSO
g` UTMR g` UTMP g` UTMN oUTNT
` UTQM oUTNU
i UMMM oNRMN ` UTQN ` POSV
oNQMO ` VUMO Å~ã MOU oOONP
oOONQ ` OOPN ` OOOO
Å~ã OMP ` i PMMO
` NQPN oNQNR ` OMOP `oPM
j PM
MM
PM
Å~ã MOT ` PQST
oOMMS
oNQQM ` VUMN ` OONM ` OOMV oOOMO ` OONT ` OONN ` OSMV oPPOM
oPPNV
` NQOO oNQNQ ` PNRN
` PMOQ
` NQOP oNQQN ` TTUP
oNQRV ` NQOM ` VUMM oPNUN oPMMO` i PMMN ` PNOS
` NMMU ` OONO oPPNS Å~ã MQR
` UTMM ` PNOQ oPNTU
oOMNN ` VUMQ oPPNR oPPPT oPNNQ oPNMR ` PMSR ` PMSQ ` PQNT` PQNR` PQNP` PQNV oPNOR` PNON
oNQPM ` TTUS` TTUR oNMOP ` OSRS oPNUO oPNRN
` PNMM oPNRO ` PNMN ` i PNOP oPNOT
` NQMN oNQQO ` TTUT ` TTUQ
oTTON ` VUMP `oPPOP
j PNM
`oPPOQ
j PNM N M ` i POMO ` PQNU` PQNS` PQNQ
oNQQP f ` PNMO
` NQMR oNNOM ` VUMR ` OSSM oPPNT ` i PNOO Å~ã MQT ` i POMN
oTTNR oOMMT ` PNPQ oPPMR ` PRMT
oTTNV oTTOM ` PNPM ` i POMM` i POM oPNOS uPNMM ` PONT
` PQNO` PONS
` PQOM
oNQPT ` TTUU oTTNT
oTTOP oTTNU
oTTNP
` VUMS` UTM N
`oOONT
j OOMM
oPPNU oPNPS oPNPR ` i PNON ` POOQ Q R
` i POM oPOM`Ni POM S` i T
` i POM POMP U V` PONN` PONP` PONR
` POM
` POM
qmPNNM
oTTNQ ` PONM` PONO` PONQ
oNQPR ` UTMP oPNOV o_PNMO
o_PNMP` PNPO oPNOU ` i PNOM ` PNPT oPNQM
oPNPP ` PQOQ ` POOM ` POOO
` i UPMM oUTMM f ` OOMP ` PNOU ` PNOM oVQPO
oNRMV oTTNO oTTNS ` UTMR` OONU ` i PNNU ` POOP ` POMM oPOMO oPOMM
oTTOO oPPORoPPOO
oPPON ` i PNNV ` POON bqMPT oVQPN
oRQTS ` OMMP ` PNPU oPNST
` PNPV ` PQOP
` kTRMNN
gTRM ` NQMP ` OMMU oPNPT ` i PNNS
` OOPS ` PQMM oVQPM
` NQQM oNQPS o_PNMQ oPNPM oPNTS
` OMMT ` PNPS ` PNPP ` PQNN` PQM
` PQNM V U
` PQM
oNQSV ` PNPNoPNPU oPNPO ` i PNNP
` PNQP
` OMMQ ` oPONQ
j POMM
oNQSU ` PNOVoPNPN oPNSS oPNPV oPNTO
` NQPVoNQRUoNQRT ` OMMS oOONO ` PNPR ` i PONQ
` NQOT ` OMMR oPNNRÅ~ã MQQ ` i PNMR ` i POM U V
` i POM ` POPO ` i PONO
` i PONP ` PORM f c j MMQ
oNQOU oPNRP
` PNMP
oPNTR oVQQM oVQPV Å~ã MRR i VQMO
` VUNN ` OSNU` OSSN` OSNV ` OONQ ` OSOR ` i PNMS
Å~ã`MOOM` OONP ` OONR
OP U oPNVMoPNUToPNUU ` PNQQ oPNNS oPNNU Å~ã MPT
Å~ã MRQ ` POPM ` POQU
o_OMMR oNRMT ` OOPQ oPNUVoPNUP ` PNMToPNNToPNMU ` VQPT ` PONV ` POPU ` PORS ` VQOS
oOONM oPNUQ
Å~ã MNT o_OMMS oNQPN oOOMN ` OSOS oOOMV
` OOMN oNSMNoPNTVoPNVUoPNRQ` PNNN` PNNP ` PNNR ` VQQV
` OOMQ ` OOMP ` OOMO ` OONS oPNRSoPNRT ` POPN ` POQV
oPNVT ` POPT ` PORR
oNRMU
` NQNU bqMPU ` VQOT ` VQPM
` VUNM c i OSMS f ` VQMR
oNQOS oPNVNoPNUS oPNMT ` i PNMN ` POOV ` POQT ` PPMU
oNRM O
` NQOV ` VUMV ` OOMR `oNSPM
j UPM`PoNSOV
j UPMO oPNVO oPNOMoPNM oPNNM
V ` POPS ` PORQ
` PNMV ` i PONN ` VQPN
oNSMM f c j MMN f ` VQMP
oNMMM oNMRM f ` NSMM ` i PNMO` PNMQ ` POPR ` POOU ` PORP ` POQS
` NMQO MN
oNM ` OSOQ oPNUR oPNRR` PNMS ` PNNU ` VQPS
oVQQN ` i PONR
oNNSO ` OOON ` i PNMM Å~ã OMQ ` POOT` POSM ` POQR
oPOM
` POQO T
` POQN f ` POMM oPONO
` PORV f ` POMN
` NMPU j UPM`Q
`oNSPN j UPMR oNSMQ
oNSPO ` i PNMPoVQPU oPOMP
Å~ã NTN
oNMMQ oNMQV ` VUMU ` i TSM
` i TSM `Oi TSM
`Si TSM U V ` VUNQ oVMTQ ` VMVM oVMTT oPNNV oPOMU
oPOMQ
oPONP
oPOMV
`M
oNMNM
R QM oNNSN `M
TSM N ` PNMO
s a TRMM ` TSM ` i TSM
` i TSM ` VMUVoVMTR f ` VMNN ` VMVO ` NSMM ` i PONM ` POQM ` PORU oVQOV oVQOT ` VQOQ
oVUMN RoNMQU
`Qi TSNM f ` OOMO
Å~ã P oNMQS oTSMM f ` NMMM ` OSSS
` OSOM oPOMS oPONN o_POMR
oTRMN `VV
oNMNMPP ` i TSMP ` i TSM T ` VMVN oNSPS oNSPToNSMT ` PONU o_PONO ` VQOU Å~ã MUQ oVQOS
oVUM
` i VUMO `PUMPT oVQOU ` VQOR
` TRMM c _TRMM oVMTP nVMOR oPNMS ` POPQ ` POPV ` PORO ` PORT
oNQNU oUMNP ` VQPO
oVQOR
oTRMM oNRNN
` NQON ` PNMR oPOMR oPONM ` VQOV
oNQSN oTROS` TRNP oOOMS Å~ã MNS nPNMM o_POMQ o_PONN
oTRRT ` TRPP nVMOS oVMTS ` i PNNR ` POPP ` PORN
oNRM R
` NQPR oTRRQ oTROT` TRNR ` OSOP ` OOOS
` OOOT
` OQOP Å~ã MVS oPPMT ` POOS ` POQQ
oTRPT ` OSOT oVMSV
oTRRN` TRNS c VMMO oPNMMa PNMM o_PNMN ` PPMT
oTRRS pPNMM o_PNMM c VQMP qmPNMO
oTRPM ` TRNU ` j VMMQ f ` VMNM oPPMS
oTRPR ` VMSM o_POMP o_PONM
oTRRP` TROM Å~ã MNU ` POOR ` POQP
oTRPV ` OSNN ` OOMS ` OOMT ` OSON ` OSOO a VMMM oVMTN ` VMRV ` VMPS ` i PNNQ
` OOMM ` OOPP
gTRMQ oTRMQ` TRMO oOOMM ` OSMO ` VMSN
oTRMU` TRMQ oOONN ` OSNQ ` OSMR
` OOPO
oOONS
oOONR
` OSMU o_POMO o_POMV
c _TRMN ` VNRO a VMMN` j VMMR ` VMPP
oTRMT` TRMR oOOMU ` OQON
` i OOMS qmPNMR o_POMM
oTSMN` TSMO
` TRPO Å~ã OU
oTRNN` TRMT ` SPMP oOOMT oVMTM oVMMM ` VMPN
qmPNMN ` OOOR oVMST Å~ã RTV o_POMN o_POMU
oUM`QQ
UM`MR OO
UM oTROR` TRNO oVMUP
oVMUO
oVMoVM
UN`TO oVMNN
nUMMMoUMQR ` UMON oNM
`SQ
NMQT VMTP oVMSU oVMNM
` VMMM
oTRNV` TRNN oSMPR ` OSNO f ` VMMV
oOSMO ` VM
`TQ
VMTS o_POMS o_POMT pUQMM
` UMQO RS
oUM nUMMN ` VMUT oVMMR oUQOO
oUQON
oUMNT oTRNR oTRNS oNMRS ` OOOM ` VMUO
oUMQPoUMQO ` VMMQ f ` VMMN ` VMOU qmPNNO
oUMNU ` OONV ` VNNQ
` i UMMoUTOP
P ` UTM Q` UTM
` UTMS T oOSM`NOQOM ` VMNM
nUMMO ` UTMO ` VUON
s a TRPO s a TRMsSa TRMN s a TRMOoTRPUs a TRMPoTRMO s a TRMQ s a TRMV s a TRMT oUMRU f ` OSMM c i OSMT ` VNON
s a TRPNs a TRPPoTROM
` i TRM N
oTRPS oTROQ a UMMN oNMQT i VMMO
` TRQO s a TRPM a TRMOoTRPQ ` TRMN a TRMQ
oTRNP a TRPO a TRMS a TRM
`M
TRNQ ` NMPS oVUMQ oOSNO
` TRQN ` TRQP a TRPSs a TRMR a TRMRoTRM aV
TRMN a TRMU oTRPN
` TRNV a TRPM oNNTOoUMRT
oNNTN ` TTPS` TTPV
Å~ã MRO ` UMNU` RSMR ` NMRM ` OSPQ
` TRQM ` i TTMT ` UMNV oOSNQ i VMMT oVMOM ` VNMV
a TRPR s a TRPR ` TRMU a TRNN oTRMP oTRNO oTROP ` TTQM oUMNQ ` NMRO Å~ã MQM
oTRNT
` TRNM
oTRMR oTRNQ oTTMR ` TTPR ` TTPU ` UMMN ` UMMM` RSMQ
oNNPQ oOSNP oVNOR oVMQO ` VMQQ` VMQO` VMPV
a TRPP
s a TRPQ ` TRQR ` TRMS oTRPO ` TRNToTROV
s a TRMUa TRPN oTRRO
a TRPQ oTRM
` TRMP S c TTMN ` j TTMO ` TTPT ` VUNO ` OSRO oVMQN
` TRQQ i TRMM oVNOQ
` TRQU ` TRMV a TRNM oTRNU oTRNM ` TTPO oTUMOc i TTMM oNMRO o_TMMQ o_TMMNoNMOVoNM
oNM NQoNNPR
NOoNMRT ` VUNP ` OSOU ` OSPS ` j VMMM oVMQM
` TRQVoTRTQ
oTRTT oTRTS oTRPP oTRVV ` i SPM N M
` i SPM ` i SPMO
oTROU ` i TRMO oTROO f ` TTMO ` NMQR RR
oNM oUMNR
` TRRN
oTRTV oTRTOoTRTU oSPMO ` NMQQ ` UM
`PS
UMPR Å~ã MRP
` i TRMR ` TRQT ` i TRMQ VoTTQT
oTTNM
oTTM oTTQS
` TRRM oTTMU o_TMMO ` NM
`PN
NM`NQ
NM`OO
NM QS` iSM
oNM OOMM
oVUMO
oOONV
aj M
Å~ã MM
MNR oSPM oSPM
N M ` i SPNO
` i TRMP ` OSOV
oOSNR
` OSRN oOSM Q` OSNS ` OSNR ` OSMN ` OSMM
R ` OSNP
oOSM
oTTM uNMMM oSPNQ
Å~ãTMTN ` SPMN` SPMM oNMQQ
` i SPMQ
` OOOU
` NMOR oSPNP o_TMMS oNM
oNM MUoNM
NPoNM RU`RV
NNoNM NMRN
oOSNN
` TRQS ` Si TTMR
oTTM oSPNU ` OQOO
oSPOS
oSPOT oNMMP ` SPMQ oOSNM bqMPP
oNNPP
oNNMM ` OQNV ` OOPM ` OQNU ` OQNT
oNMMO oSPNR ` OQNS oTMOOoTMNT
` TTPQ ` TTPP ` j SPMN oSPMP `NU
` NMNM`MP`NM
NM NM
`QUoNNPO
NMQV
oNNMN
` j SPMM h^MMQ
` SPMO o_TMOO o_TMNN o_TMNU
` i NMMV o_TMOR
` i TTRN oTMMQ
oTUQS
` i TTRMoTUROoTUQV oNMRN
oTUQT
oTURPoTUQU ` TMMU oTMNR
` SMNN ` SMOP ` TUOQ ` TUPN ` i TTRO oTMOP
oSMMU c _SMMP ` SMMV ` TUOP oNMVU
` i ROON uTMMM
oTRTN
` i TTRPoTRTP ` j TTMPoTRTR
oTVSM o_TMON Å~ã MPV
oSMMT c _SMMO ` SMMU oTUNN oTRTMoTVSO bqMPQ o_TMPO PR oTM
oTMoTMPQ PP
` SMNM ` SMOO ` TUNV Å~ã MTO oNNOP
` TUPO ` NQPU oTMNVo_TMNO
` TUON ` TUTN
oTUNP oNMOT` NMOP o_TMMT oTMMO oTMPO
` j TTMS oNQRS oUMRV oTMMV
o_TTNP o_TTNO oTUNR ` NQPT oNQRR oNMOU oTMOU Å~ã MRT
oUMSM
` TUOM f ` TTMT ` TUTO
oTUNQ o_TMMR ` UQOT
oNMNM oTMOR`OQ
oTM NMOT oUMSO o_TMNS
oNQSToNQSS
o_TMNQ oUMSN oTMMU oTMOV ` TMMR
` TUTM ` NMMT oTMNU o_TMMU
oTMMT oTMMR ` UQOS
` RSMO ` TMNM f ` TMMP
oRSNP`oRPRN oNMMV ` TMMV oUQOP
oTVTP` TUOO oSPNV` i SPMR ` RSMP j ROMO
oSPON oRSNO o_TMPP o_TMNP o_TMPN ` UQOO
`OM
NMoNNOQ
MR Å~ã MTS
oSPOM
` i SPNN oTM ` UQNU oTMNN oTMOT
Å~ã NR ` i SPM U` iSSPMT o_TMMV
oSPORoSPOO ` i SPM nRSMR oTMOS
` jNR
oSM SM MQNS
` SM oSMTM oUQNV oTMNM
o_TMOP o_TMOU ` UQOR
` jNS
oSM SM MRNT
` SM oSPOP ` i SPMV f ` UQMP ` TMMS
` SMNO ` i SPNM
oSMTNf ` SMMM oSPOQ oRSNQoRSNR o_TMNV ` TMMT
` jNT
oSM SMMS `oSM
j SMTO
NO o_TMOM
oSM oTMPM ` UQON
oUQMN M
oUQM
` jNU
SMMT oSMMV ` UQNT oTMPN ` TMMO
` jOM
oSM SM MUOR
` SM ` SMÅ~ã
TM MoSM
SS NM
g` ROOT oUQMO Å~ã MTQ Å~ã
oTMMS MRS
` jON
oSM SM MVOS
` SM oSMSV ` TMMN
oSPNSoSPNT ` kTMMN ` kUQMM ^TMMN
` j SMNM g` ROPR g` ROOU g` ROQP ` TMMQ
oSMOO o_TMOV ` TMMP
oSMPP ` j SMNN g` ROPS oRQUM f ` TMMO
g` ROQN g` ROQQ oTMMP
f ` UQMM ` UQOU
oSUMM g` ROQO
` UQPM
oRRMS oRRMQ o_TMOS o_TMPR
oSUMN oRRMN oRQVV ` RPRP ` RPRS
` RPTT ` RPTS ` ROVU uROMO
` RPSN
oSUMO ` i RSMQ oRRMR oRRMP ` UQMM
oRSOP
oRSOO oRRMO oRRMM ` RPSO
oSUMP oRQTU
oRPSU
oRSNS ` RPPV ` ROVT oUQMR
oSMMP oRSOM ` RPMR ` RPRQ oUQM
oUQNP P U
oUQM o_TMPM
`TUQOM
` UQOQ ` UQM
oSMMQ oRSON ` RPMT ` RPMS
` RPPS ` RPQO ` RPMU ` RPMV ` RPPM
` RPPT ` RPQM
` RPTR ` RPTQ
` RPQN ` RPRO ` UQOP o_TMMP ` UQMV
` RPMQ ` RPQP ` RPPU oRQOO
` RPNR ` RPPR oUQMS
nVMNU oRSNT oRQMM ` RPOS Å~ã MPN oTMNQ
^SMMM ` SMMT` SMMS oRPVV oUQNO oUQNQ
oRSNU oTMNP
c VMMV oTVTV Å~ã MUO ` RPRR oUQNR
` SMMRoSM
oSM MS`M
SM MQoSM
RoSM MN MO ` TUNS Å~ã MSR oTMNO a UQMM
c _SMMN oVNVM ` TUNP oRSNV nROMU ` RPNQ ` RPOM ` UQMS oUQMT o_TMPQ
` TUMU ` UQMR f ` UQMN o_TMOT
oVNUV oTUMVoTUMT ` RPNM f ` UQMO
` SM
`MO MN
SM ` TUNU ` UQMP
` TUNQoTUMU oRQON `NQ
oVMVMMO
` SM`OM
SMON ` j TTMR ` RPNN
` RPTU
o_RONM oUQNM
o_TMNM ` UQNM c UQMM
c _SMMS ` TUMS
` TUMT oVMNR oVMMO oUQMV Å~ã MRN Å~ã RTT
oRQOQ oRQNV oTMMN
` VNOM ` TUMR f ` TTMP o_TTNNo_TTNM ` VMMU
` VMNO o_TMNT
oRQOP oVMMoVM
U MP ` UQMOoUQMQoUQOM ` UQMN
o_TTMU ` RPNT o_ROON ` RPTP oUQNS
` SMNV oVNVO
oVNVP oVMMN oUQNToUQNU
` SMNU oVMNV o_ROMV o_TMNR
oSM
oSMSO SP c _SMMR c SMMM nVMNV ` TUNOoTUMQ oVMNS
oVMNT ` RPON ` UQNV o_TMOQ
` TUNT Å~ã MTU ` l j TMM
oTUMRoTUMS oRQNT
oSMSN a ROMT oRQNUo_ROOO ` RPOO uUQMM
` TUNN oTMON
oSMNN ` TUNM ` TUNR o_TTMV ` VMMP ` RPSM f ` VMMO
` SMOQ ` SMPM oSM ` TUMV o_ROOP oRQPN ` RPOT
` jSU
SMMP qmPNMQ ` VMQP
` SMOV oSM oRQPM ` RPOR ` VMPQ ` VMPT oTMNS
` j NQ
SMMOoSMSR a ROMU oRPVT
oRPVU
` SMOU oSM a NQMO oRQPP ` RPPO o_RONO ` VMPO
` j NP
SMMNoSMSQ oNQUV ` NQRR f ` VMMM ` VMQM Å~ã NQ
` j NO
SMMM
oSMSS Å~ã MOO oRQPO ` RPMP oVOMT
` SMOT oSM oNQUS oROVV ` VNNM c VMNN oVOMS oVOM R O
oVOM
` VMTT oNQTU ` NQQV Å~ã MTT oRQPQ ` VNPV oVOMQ
oNQUT oROVU` i ROOU ` RPTO oVMPO oUMMS
i VMMR oSMNVoSMST `RU
oVMVMRP oNQUR f ` NQMQ oRPNO oVMMS oRQPR o_RONN c VMMP Å~ã MQN
o_NQMM `oRQOT
` i ROSVj ROM` iSROTN ` RPOP ` VMOV oVOMP oUMMR` UMMT
oSMPS oVMoVM
RM QU oRPM`UROVQ oRQPT f ` RONO ` VNQO a UMMM
nSMMN ` VMMR oVMPN ` UMNN`M
oUM P`NQ
UM UMNM
` VMTN ` VMRRoVMRV
` VMRU oRQPS` i RPM`oRQUN
j NROM
` iTROTO ` RPOQ ` VNQN
` i UMMM
oVMRP Å~ã MUM ` i ROTP` RPPN i VMMP
nROMP oRQPU oRPVN
` i ROSN ` i ROSO ` VNPT ` VNPS ` VNPR f ` VMNQ o_UMMP
` SMNP ` RPRV oVMPP
` VMSS ` VMSP ` VNNN ` SUMM qmPNMP nROMQ oRQPV ` VNQM ` UMMU
` SMNQ oNQTV ` i ROTQ oRPVM
` i RORV ` i ROSM ` VNPU
` NQRM oRPMV oRQQN ` i ROTR
` i ROTS oRQTT
` VMTV Å~ã MVM f ` NQMN ` i ROTT ` RPUN ` UMMS f ` UMMO
` SMNR c _SUMM oRQQM ` RPPP ` UMNO uUMMM
` i RSMM ` i ROSP
` i ROSQ oRPVP oUMMM
f ` VMMS oRQQO oRQQQ oUMOP
` VMUP c _SMMQ ` i RSMN ` i ROTU ` RPUO oRQVU oUMOQ
oVMTV ` VMUQ oRQQP oRQQR oRPVQ oUMMO
` VMTO ` VMTU oRSNM ` i ROTV ` RPQT ` VNQV oUMMN
f ` VMMR qr SUMO c VMNM oRPVR Å~ã MSQ
` VMST oRSNN oRQRQ oRQRN
` UMPM oRQRP oRQMU ` VNQS ` VNQR ` VNQQ oUMMQ` UMM
`VUMNP
oVMTU ` VMUM oUMSU
Å~ã MST oUMPO oRQRR nROMS
oRQTV ` RPRT oRQMT i VMMU oUMST ` UQOV
oUQOQ
` VNNO a NQMM ` UMOV s aM
RSMM ` i RSMO oRQQS
Å~ã NO a RSM oRQRO oRQMS
oVMUM ` i RSMP oRQQT
oVMQV oVMRO ` VMSQ ` RSMS oRQMR oVNOP oVNOOoVNONoVNOM
` VMRT f ` UMMS f ` UMMR oRQMV oUMTO
oVMRT ` VMRQ qr SMMP i VMMS ` i ROQUnROMM oRPVS
a ROMP Å~ã MTR
oVMQT oUMNNoUMMUoUM
oUM OT QN
` SMMP oRQUP
oRPPU oRPQM
oRPQN oRQUO
oRPPV a ROMQ `oRPTP
j ROMP
` VMRO RS
oVM oRQVN oRPQT ` RPPQ o_ROMS oRRMU
` ROQS oUMQV ` UQNN ` UQNQ ` UQNP ` UQNO ` UQMU
oNQTN
oNQTMoNQUM oRQUT
oRQVM Å~ã MUU ` ROMM oROSUoRPTQoRPRT
Å~ã NUN nROMV oROMT oROMU oRQTP oRRMT oUMQU oUM MToUM
oUM OS QM
` UMOU ` ROVS
` NQRQ Å~ã O ` i ROQM ` ROQT
` NQQP ` NQRP s a NQMM ` ROVR a ROMM oRQUQ oUMQT oUMSS
` NQQQ oUMPNÅ~ã MSU ` i ROVT
` i ROVV ` i RORR
` i RORT` i RORP ` RPQU` RPRN o_ROMR f ` ROMU
oRQTQ ` i ROVR
` i ROVP ` i ROOR
` i ROOS ` i RORN
oRRON ` RPRM oUMRM oUMQSf ` UMMV oUMSR Å~ã MNQ
oRQUV a ROMN ` RPSP oRQVQ
oRQVT oUMRQ
` TRON s a UMMU oRQTR oRPQR ` RPNV ` RPSR
` RPSQ ` RPSS
` RPOU ` RPNU
` RPST ` RPSU ` i RPM
` i ROVQ` i ROVU M
` RPOV ` i RORQ
` i RORS
` i RORU ` i RORO` RPQV oRQRT ` i ROPV oUMSQ
` NQQR f ` NQMO ` TRSM
oTRVP oUMPP oUMRR
a TRNO
oTRRU ` TRSO g` UMMR oRONOa ROMO
oRONN oRQUR
` i ROVS oRQVR o_ROOQ f ` ROMM
` ROQU` ROQV oUMSP
oTRON oTRVO ` UMPVi UMMN i UMMO oRQUU oROTQ oRROO oROON
oROSR f ` UMNMoUMRP
` TRRV oRPRP ` kROMM oUMPS
` NQQS oNQUN s a TROM oROMV oRQTO oRPOMoROVT oRQRM
oRQQV oROVQ
oRQQU oROVRo_ROOM
oROVP oRQVS oUM Å~ã MTP f ` UMMT ` UMPN g` UMMM
s a TRPU ` TRSN o_RONR oROTP Å~ã MQORN oUMTN s a UM
oUM
MVPR g` UMMN
s a UMNM
s a UMNN sPa UMM
s a UMM sOa UMNPs a UMNO o_RONQ
c _TRMO a TRNQ s a TRPV qmPNMT oRONM o_RONP oROVS ` UMPU ` UMQM
oNQTR a TRNP a TRPT ` ROOOnROMN Å~ã MUN oUMPToUMRO sNa UMMM
s a UMM
o_RONS ` i ROOT Å~ã MTM Å~ã MSV oUMPU oUMNO s a UMMsRa UMMQ
` l j TRN oUMTP oTUNU` TUPR ` TUPQ` j TTM
`T
TUPP ` UMM`QUMMP oUM
s a UMMS MV qmPNMM
a TRPU `oRPTR
j ROM
oRPTS `QoRPTT
oRPTUj ROMRoRPTV
oRPUM a ROM
aSROMR ` UMPO f ` UMMM ` UMM O f oj MMO h^MMO
Å~ã MUS oNQTP
oNQTO Å~ã U oTRSO ` RPUM
oRQSU ` UMPQ f ` UMMU Å~ã VMP s a TTMO s a TTMN s a TTMM
oTUQR oUMTMSV
oUM Å~ã S
Å~ã MPS oRQST Å~ã MSO Å~ã MMV
s a NQMN
s a NQMO oTRSN ` RPTN oRQOU oRROM
` RPVM Å~ã MSP
` j ROMM o_RONV oRRNS
` RPUT
oRRNR` RPUU o_RONU Å~ã PTT
o_ROMU oRQOV o_ROMT oRROQ
oRROS ` RPTV ` RPTM s a ROMP f ` UMMN
g` ROQM g` ROPV g` ROPU g` ROPT ` RPUV g` ROMU oRRMV` RPUR
Å~ã OUU s a RONM
s a RONO oRROR
s a ROMU s a ROM
sSa ROMT oRRNT oRRNV
oRRNU
s a ROM sOa ROM
s a ROM Q g` ROMV
oRQRS oRROP
s a ROMN s a ROMRg` RONT g` RONS
qr SMMN s a RONN Å~ã MOV Å~ã MPM ` iVROPT Å~ã MOS oRRNM oUMNM
` i ROPU Å~ã VMO
Å~ã Q ` i ROVO ` i ROTM Å~ã N ` i ROQR
Å~ã MNR
qr SMMM
Å~ã MMT qmPNNP
` kUMMM ` kUMMO
gTRMR ` kUMMR
gNQMN
gTTMM
` kROMU ` kROMP ` kROMO ` kROMN

Å~ã MNM Å~ã MMO Å~ã MMP Å~ã MMQ Å~ã MMN

Å~ã MMS Å~ã MMR

Å~ã MMQ

Å~ã MMN Å~ã MMO

hgMMN hgMMO

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 133

 DIAGRAMS

BMFW (B SIDE)

hgMMQ hgMMP
Å~ã MMT

Å~ã MMU

` j TTMQ

gi SMOV

gi UMMO
gi ROMU

gi SMMR

gi UMMT gi UMMRgi UMMS gi UMMU

gi SMMU
gi UMOQ f oj MMQ h_MMO
gi ROMV
bqMMS gi UMNN
gi SMMT gi UMMPgi UMMQ gi ROMS gi UMMMgi UMMVgi UMNM
gi ROMR
bqSMMM
bqSMMN gi ROMQ

gi ROMO
gi SMMV gi ROMN gi ROMP

` RPUP
gi SMPM
gi SMNMgi SMNNgi SMOU gi SMNV ` RPUQ gi ROMT
` i ROUP
` i ROUO a j MMO
` i ROSU
` i ROUQ
` i ROUR
` i ROUS
` i ROUT
` i ROUU
` i ROUV
` i ROVM
` i ROSS
gi VMON ` i ROST

gi VMOO
gi SMPQ

gi SMNQgi SMNS gi SMOMgi SMOO gi SMOR

h_MMQ
gi SMNOgi SMNP gi SUMO gi SMNRgi SMNT gi SMONgi SMOP gi SMOQgi SMOS gi SMPO ` i ROUN
` i ROUM
bqMNR

gi SMOT bqMOT

bqMOP

gi SMMS gi SMPN gi SMNU

bqMNV
gi SMPP

gi SMMQ

bqMOV

bqMOR ` j TTMN

bqMNO

gi TUNS gi VMNR

` i TTSQ
` i SMMM gi VMNS
` i UMMQ
` i UMMR
` i TTSP
bqMOU
` i TSMM
` i TSMN
` i NM
` iM
NM
MMN
bqMOO ` i VUMM
` i VUNM

` i VUMN
gi TRMT gi TRMS ` i VUMR` i VUMP
gi PNMP
gi PNMO
bqMMV
gi VMOQ
gi PNMM
gi PNMN

gi TRMM
` i UPMT̀ i UPMU ` i UPMN
bqMNQ
gi PNMQgi PNMR
` i TTMU

gi VUMM
bqMNP

bqMNU
gi TUPM
Å~ã MMU

gi UMNP
gi TUPN
gi UMNR gi UMNQ gi VMNU ` i UTNN
bqMMT ` i UTNM
gi UMNO
gi TUOV

` i UTMV
` i UTMU

` i UTMT ` i UTMS

gi NMNR

gi NMNQ

gi NMNP gi NQMV gi NQMU bqMOQ bqMNN

gi NMMV gi NQMR gi NQMQ gi NQMP gi NQMO gi NQMN
gi VMOP ` i PNMV
gi NMNO
` i PSMQ
gi NQMM
gi NMNN gi NQMT gi NQMS gi NQNM gi PSMN
Å~ã OMU
Å~ã OP
gi NMNM gi NQNO gi NQNN
Å~ã OMV
bqMPM

Å~ã NS Å~ã NT
Å~ã MVO

Å~ã ONM

Å~ã MVP

Å~ã MVQ
Å~ã MMS
gi VMNT

Å~ã MVV

gi VMOR

bqMOS
gi VMNV bqMNS
h_MMP
Å~ã MQU
gi VMOS

bqMNT
gi VMOM

bqMON

gi UMNS
h_MMN

gi UMNT
gi TUOQgi TUOPgi TUOOgi TUONgi TUOMgi TUNVgi TUNUgi TUNT gi TTVQ gi TTVM
gi NMMQ
gi TTVR gi TTUV
gi TUMN gi TTVN
f oj MMP gi NMMT
gi TUMM gi NMMN
gi TUNP gi TTVV gi TUNR gi NMMPgi NMMR
gi TUMO gi TUPO
gi TUNQ gi VMNO gi VMNP
gi NMMO gi NMMU
gi TTVU gi NMMM gi NMMS
gi TTUU gi VMMVgi VMNQ gi VMMTgi VMMRgi VMMPgi VMMN
gi TUMQgi TUMP
gi PSMM
gi VMNM

gi VMNN gi VMMUgi VMMSgi VMMQgi VMMOgi VMMM

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 134

 DIAGRAMS

4-4. CIRCUIT BOARDS LOCATION

KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

BMFW

SWITCH UNIT

GL4 SMART CORE

KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C
BMFW
SMART CORE (M, L)

HSC3_S_M

SWITCH UNIT

WLAN/BT MODULE

GL4 SMART CORE

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 135

SEC 5. EXPLODED VIEWS
• Items with no part number and no description are not stocked because they are seldom required for routine service.
• The construction parts of an assembled part are indicated with a collation number in the remark column.
• Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated
when ordering these items.

5-1. KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C

5-1-1. REAR COVER REF. No. PART No. DESCRIPTION MARK
1 1-798-510-31 SWITCH UNIT (SM-G-WW)
2 4-563-755-31 LABEL, SIDE TERMINAL (W)
3 4-563-766-01 LABEL, REAR TERMINAL
4 4-297-989-01 AC COVER
5 1-839-667-12 POWER-SUPPLY CORD (WITH CONN.) UKA
5 1-839-691-12 POWER-SUPPLY CORD (WITH CONN.) CEI/RU3
6 4-559-708-01 REAR COVER (SM HRN) A
7 1-754-953-11 BT ANTENNA
8 1-859-100-11 SPEAKER BOX ASSY (L)
9 1-859-100-21 SPEAKER BOX ASSY (R)
10 4-567-609-01 LABEL, CI
1 10

SMART CORE
2

7 4 3

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 136

 EXPLODED VIEWS

5-1-2. LCD PANEL REF. No. PART No. DESCRIPTION MARK

51 1-812-098-11 LCD PANEL (Y43QHNDS) KD-43X8307C
51 1-812-099-11 LCD PANEL (Y43QHNDB) Except KD-43X8307C
52 4-546-444-41 BRACKET, SIDE F (MOLD)
51 53 A-2072-550-A COMPLE SVC (XF) BMFW CEI
54 1-474-621-11 GL4 (CH)-STATIC CONVERTER (TV)
55 4-565-060-01 SHEET, INSULATION (HRN S)
56 4-562-155-01 BRACKET,SC (HRN)
59
57 2-650-770-21 SLIDE, CLAMP
58 4-566-017-01 BRACKET, SP (LAK)
52
59 4-546-441-11 BRACKET, TOP FL (MOLD)

58
57

56 53

55

57 54
56

58

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 137

 EXPLODED VIEWS

5-1-3. CONNECTORS

101 102

104

103

PART No. DESCRIPTION MARK

101 1-910-110-19 CONNECTOR ASSY 28P CN6401 (GL4/GL5) -CN9000 (BMFW) -TCON (1)
102 1-848-925-11 FLEXIBLE FLAT CABLE 41P (XFA) CN3600 (BMFW) -TCON (1)
103 1-910-110-20 HARNESS ASSY (MAIN) CN1000 (BMFW) -CN101 (HSC3) -WIFI-SM/CN7700 (BMFW) -SP (1)
104 1-848-920-11 FLEXIBLE FLAT CABLE 51P (XFA) CN3601 (BMFW) -TCON (1)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 138

 EXPLODED VIEWS

5-1-4. SCREWS

REF. DESCRIPTION PART No.

SCREW +PSW M4X10 4-159-298-01

SCREW , +PWH M3X6 4-452-935-11
SCREW, +BVTP 4X12 TYPE2 IT-3 2-580-639-01
SCREW (+PSW)(M3X6) 2-990-421-41
SCREW, +PSW M3X6 W12 4-256-393-11

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 139

 EXPLODED VIEWS

5-2. KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C

5-2-1. REAR COVER REF. No. PART No. DESCRIPTION MARK
201 4-567-609-01 LABEL, CI
202 4-563-755-31 LABEL, SIDE TERMINAL (W)
203 4-563-766-01 LABEL, REAR TERMINAL
204 4-297-989-01 AC COVER
205 1-839-667-12 POWER-SUPPLY CORD (WITH CONN.) UKA
205 1-839-691-12 POWER-SUPPLY CORD (WITH CONN.) Except UKA
206 4-567-563-01 REAR COVER (M HRN) A
207 1-754-955-11 BT ANTENNA
208 1-859-100-11 SPEAKER BOX ASSY (L)
209 1-859-100-21 SPEAKER BOX ASSY (R)
210 1-798-510-31 SWITCH UNIT (SM-G-WW)
210

201

208

SMART CORE

209

202
207
203

204

205

206

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 140

 EXPLODED VIEWS

5-2-2. LCD PANEL REF. No. PART No. DESCRIPTION MARK

251 4-546-441-11 BRACKET, TOP FL (MOLD)
252 4-546-444-41 BRACKET, SIDE F (MOLD)
253 A-2072-550-A COMPLE SVC (XF) BMFW CEI
254 1-474-621-11 GL4(CH)-STATIC CONVERTER (TV)
255 4-565-060-01 SHEET, INSULATION(HRN S)
256 4-562-155-01 BRACKET, SC (HRN)
257 2-650-770-21 SLIDE, CLAMP
211
258 4-566-017-01 BRACKET, SP (LAK)
259 1-812-100-11 LCD PANEL (Y49QHNDS) KD-49X8307C
259 1-812-101-11 LCD PANEL (Y49QHNDB) Except KD-49X8307C

251

258
257
252

253
256
255

254
257 256

258

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 141

 EXPLODED VIEWS

5-2-3. CONNECTORS

302 301

303

304

REF.NO. PART No. DESCRIPTION MARK

301 1-848-926-11 FLEXIBLE FLAT CABLE 41P (XFB) [CN3600 (BMFW) -TCON (1)]
302 1-910-110-21 CONNECTOR ASSY 28P CN6401 (GL4/GL5) -CN9000 (BMFW) -TCON (1)
303 1-848-921-11 FLEXIBLE FLAT CABLE 51P (XFB) [CN3601 (BMFW) -TCON (1)]
304 1-910-110-22 HARNESS ASSY (MAIN) CN1000 (BMFW) -CN101 (HSC3) -WIFI-SM/CN7700 (BMFW) -SP (1)

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 142

 EXPLODED VIEWS

5-2-4. SCREWS

REF. DESCRIPTION PART No.

SCREW +PSW M4X10 4-159-298-01

SCREW , +PWH M3X6 4-452-935-11
SCREW, +BVTP 4X12 TYPE2 IT-3 2-580-639-01
SCREW (+PSW)(M3X6) 2-990-421-41
SCREW, +PSW M3X6 W12 4-256-393-11

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 143

 EXPLODED VIEWS

5-3. KD-43X8301C (FW-43X8370C)/ 8305C/8307C/8308C/8309C,

KD-49X8301C (FW-49X8370C)/ 8305C/8307C/8308C/8309C
5-3-1. SMART CORE (M, L) REF. No. PART No. DESCRIPTION MARK
601 4-547-392-01 CASE, BOTTOM (M)
602 A-2066-088-A HSC3_S_M MOUNT
603 4-547-390-02 LIGHT, GUIDE
604 4-547-389-01 PANEL, ORNAMENT
607
605 4-547-395-01 COVER, TOP
606 4-547-397-01 BRACKET, WIFI
607 1-458-853-11 WLAN/BT MODULE(11AC)
608 4-566-841-01 HEAT SINK L(SC)

608

606

605

604

602
603

601

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 144

 EXPLODED VIEWS

5-4. OTHER PART

5-4-1. MISCELLANEOUS 5-4-2. ACCESSORIES

PART No. DESCRIPTION MARK PART No. DESCRIPTION MARK

* 4-144-046-11 LABEL, COMBI 1-492-961-11 REMOTE COMMANDER (RMT-TX100E) RU3
4-262-708-04 CLAMPER, CABLE 1-492-963-11 REMOTE COMMANDER (RMT-TX100D) Except RU3
4-449-083-11 SPACER (22) +C
4-547-493-01 HEAT, SINK (MUFF) 4-562-157-01 STAND (SM HRN) A 43": X8301C (X8370C) /8305C
4-548-743-01 HOLDER, HS WS (MUF) 4-562-157-11 STAND (SM HRN) A 43": X8307C/8308C/8309C
4-549-186-01 SHEET, THERMAL (BM) 4-562-158-01 STAND (M HRN) A 49": X8301C/8305C
4-549-188-01 HOLDER (HS MUF) 4-562-158-11 STAND (M HRN) A 49": X8307C/8308C/8309C
4-549-395-01 HEAT SINK (MUFF C) 4-564-539-01 STAND NECK ASSY (LAK)
7-600-040-44 ADHESIVE (SV380C) 333CC GRY
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 4-449-743-01 SCREW, +PSW M5X16
7-600-031-97 TAPE (3M 1350FB-1) 15MMX66M BLK

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 145

END

English
2015DL08-Data
Made in Japan
9-888-570-01 Sony Visual Products Inc. © 2015. 4
KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 146
APPENDIX-1
How to USB update

1:Download USB image and unzip file.

2: copy unzip file to USB memory root folder.

3: USB memory insert TV.

4:USB image is newer soft version. 4:USB image is not newer soft version.
Automatically show message and start update. Automatically show message and start update.
Please follow directions. Please follow directions.

Copying update file from USB. Please wait...

Preparing for system software update. During the No newer version of the system software was found.
system software update, the TV will automatically Please remove the USB device and select “OK” to exit.
restart. Please do not remove the USB device until an
update complete message is displayed. The update may
take up to 30 minutes to complete.

5: finished

The system software update is complete.

Some user settings may have changed during the update.
Please remove the USB device and select "OK" to exit.

5: finished

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 147

 APPENDIX-1

Software update for B board replacement

Check the leftmost bit

B board replacement
of NVM version by “0”
Service mode to
confirm RCD version.
Is it except 0 or 0?
<Case1>
After AC Plug-in, wait for 30sec Panel : No Picture Except “0” Check the software
then turn on TV by power key SMART CORE LED : Red LED 3x blinking version by Service
on TV or remote commander. mode.
Is it latest version?
No
Model Number setting
<Case3> Yes
Panel : Picture appear
SMART CORE LED : White Lit
Check condition.
Is it the Case 1,2 or 3?
Update to the latest software
<Case2> version
Panel : No Picture *Remove all signal connection.
SMART CORE LED : Amber & Green blinking (antenna, external input, ether
cable, etc)
Update to the latest software *Insert the USB memory. Serial Number input and
version SMART CORE LED will change WB/Gamma, MURA, CUC data
*Remove all signal connection. Check Model name by to white blinking. *After transfer by Service mode
Different
(antenna, external input, ether Service mode. completes, TV will reboot by itself
cable, etc) Is it the same or and turns on.
*Insert the USB memory. different? *Disconnect the USB memory.
SMART CORE LED will change
Reconfirm Software version
to white blinking. *After Same
and Model name by Service
completes, TV will reboot by
Check NVM version mode
itself and turns on. Note1:
*Disconnect the USB memory. affix by Service mode For a success of software writing,
Different
to confirm the country. it will take 20~30 min/time.
Is it the same or
Note2: Turn off the TV by remote
different?
Do not turn off TV while updating software. power key then reboot the set
Same If older software package version is used, software (AC OFF wait 10sec then AC
cannot be update. plug-in), turn on the TV by
TV will reboot and turn on again. remote power key.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 148

 APPENDIX-1

Software update for Panel/T-CON replacement

Check the software version No

Panel/T-CON replacement by Service mode. Model Number setting
Is it latest version?

Yes

After AC Plug-in, wait for 30sec then Update to the latest software
turn on TV by power key on TV or version
remote commander. *Remove all signal connection.
(antenna, external input, ether cable,
etc)
*Insert the USB memory.
SMART CORE LED will change to
white blinking. *After completes, TV
Check condition will reboot by itself and turns on.
Is it the Case 1 or 2? *Disconnect the USB memory.
<Case2>
Panel : Picture appear
SMART CORE LED : White Lit

<Case1> WB/Gamma, MURA, CUC data

Panel : No Picture transfer by Service mode
SMART CORE LED : Amber & Green blinking

Update to the latest software

version
*Remove all signal connection. Note1: Reconfirm Software version and
(antenna, external input, ether cable, For a success of software writing, Model name by Service mode
etc) it will take 20~30 min/time.
*Insert the USB memory.
SMART CORE LED will change to
Note2:
white blinking. *After completes, TV Do not turn off TV while updating software.
will reboot by itself and turns on. If older software package version is used, software cannot be update. Turn off the TV by remote power key
*Disconnect the USB memory. TV will reboot and turn on again. then reboot the set (AC OFF wait
10sec then AC plug-in), turn on the TV
by remote power key.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 149

APPENDIX-2
Wire Dressing (KD-43X8301C (FW-43X8370C)/8305C/8307C/8308C/8309C)

VA Tape x6 Harness Tie x4 Slide Clamp x2

• Fix wire • Fix wire • Hold wires

150

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 150

 APPENDIX-2

Wire Dressing (KD-49X8301C (FW-49X8370C)/8305C/8307C/8308C/8309C)

VA Tape x7 Harness Tie x5 Slide Clamp x2

• Fix wire • Fix wire • Hold wires

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 151

APPENDIX-3
HANDLING GUIDANCE
Unpacking(1/2)

1.Take out panel from carton box with proper number of operator.
≧43” MINIMUM NUMBER OF
OPERATOR

≧43”
2

2.Take out panel straight out from carton box.

When taking out a panel,

be careful not to hit front panel and back panel.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 152

 APPENDIX-3

HANDLING GUIDANCE
Unpacking(2/2)

3. Do not hold or press glass (TFT cell).

Glass area
Glass area

4. Put in “separator board” between panel and panel.

When “vacuum handling jig” is used.

When taking out a panel,

be careful not to hit next panel module.
Separator board

*Please prepare “Separator board” by yourself.

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 153

 APPENDIX-3

HANDLING GUIDANCE
Carrying (1/2) MINIMUM NUMBER OF OPERATOR
43” 49”
DO NOT HOLD PANEL HORIZONTALLY AT ALL TIMES. 1 2

1. Carry panel vertically.

PANEL WILL WARP IF HANDLED LIKE THIS PICTURE

2. Do not hold glass area(TFT Cell area).

Glass area Glass area

AL BEZEL

Glass area

AL BEZEL

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 154

 APPENDIX-3

HANDLING GUIDANCE
Carrying (2/2) MINIMUM NUMBER OF OPERATOR
43” 49”
1 2
3. When carrying by only 1 person, hold panel at top and bottom center position.

4. For large panels, sizes 49” or larger, hold panel by 2 people.

≧49” ≧49”

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 155

 APPENDIX-3

HANDLING GUIDANCE
Placing to table
For panels 43” inches or larger, follow guidelines below. MINIMUM NUMBER OF
OPERATOR
43”, 49”
1. Steps to place panel to table. 2

(1) Place vertically. (2) Change hold position. (3) Place to table.

2. Place panel by 2 people. 3. Place panel within table 4. Table must not have any step.
surface.

STEP

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 156

 APPENDIX-3

HANDLING GUIDANCE
Others
1. Do not press panel during fixing screw. 3. When attaching or detaching
vacuum handling jig to panel,
maximum force on panel shall be
less than 100N total.

Less than 100N

total

4. Operator must wear gloves.

Do not touch Panel module without gloves.
2. Do not hold or touch glass (TFT cell) at all times.

Glass area

KD-43/49X8301C (FW-43/49X8370C), 8305C, 8307C, 8308C, 8309C 157