Sr.
No Description Make Equivalent =Approved by TCL Incharge
1 Internal and External Painting work Asian
2 Cement JK /Ultratek /Equivalent
3 Waterproofing chemicals Fosroc/Sikka/Dr.fixit/Pidilite/Equivalent
4 bounding agents Fosroc/Sikka/Dr.fixit/Pidilite/Equivalent
5 Epoxy painting MRF/Equivalent
6 ACP sheet Eurobond/Equivalent
7 MS (Mild Steel ) JSW/Equivalent
8 Ceiling Gyproc /Saddam
If Any missing consultant suggest
t =Approved by TCL Incharge
TATA COMMUNICATION,DIGHI, PUNE.
Coral BILL OF QUANTITIES
POLYMER
SECTION A: STRUCTURALREPAIR OF COLUMS AND BEAMS: Providing & laying Polymer Modified Cement Mortar (PCM) for damaged R.C members of External area
REPAIRS
Sr No upto 20-40 mm thk., as per T-S3 using "Acrylic based polymer" with the procedure given below. Remove all the loose concrete/cover completely and
Description Unit
clean the reinforcement with wire brush. Apply "Rust Remover" by means of cotton waste swab to the reinforcement. Wash with water jet after 4 hours
of this application. After 24 hours clean the reinforcement with wire brush or tap very gently with wooden strip or inverted chisel. Apply a passivation
A1 coat of "Rust inhibitor" & cement slurry in 1:1 proportion to the chemically de-rusted surface of steel. Repeat the same coat after 4 hours of the first coat. SQFT
Apply priming cum bonding coat of "Acrylic based polymer" & cement slurry in 1:1 to the concrete by brush. Immediately place polymer modified
mortar (PCM) in 1:5:15 by weight, prepared by mixing of "Acrylic based polymer" per bag of cement. [Water shall be added for desired consistency].
A2 NOTE: PolymerREPAIRS
STRUCTURAL Modified ON Mortar
RCCshould
ITEMSbe applied byADDITION
WITHOUT hands in layers of thickness
OF POLYMERS ASnot exceedingBY
DIRECTED 10-12mm.
C.E Apply
as item no. bond coat on every layer. PCM as
NOZZEL GROUTING : Providing injections to core concrete of columns and beams by drilling holes of 12mm dia forA1.
a depth of 30 to 50mm inside the SQFT
above but by embedding Khadi (aggregate 10/20mm sige) as per site 'requirements and as directed by Edifice Erection’s Consultant
damage & honey combed concrete area at spacing with PVC or aluminum nipples and sealed periphery by polymer modified mortar and Pressure
grouting it with neat cement polymer based chemical slurry for severely damaged RCC members as directed by CE. Grout into concrete/brick work by
A3 NOS.
suitable gun/pump at required pressures by providing
EFFECTIVE BOND COAT
necessary, scaffolding, : Providing
drilling & applying
and inserting 12mm effective bonding
dia aluminium coat between
grouting old and new
multiperferated concrete
nipples upto /30mm
mortar to of approved
40mm depth,brands
using of
`Mpolymer based
Seal around
chemicals
the nipple as per manufacturer’s
cutting of nipples after specifications.
curing, cleaningProviding
etc. and applying priming cum bonding coat of
Complete
A4 LTR
polymer of approved make and quality as approved by Engineer-in-charge and cement slurry in1:1 proportionate by weight to concrete area by brush or
any other
STEEL establishment method etc. Complete. ( Item shall be execute after exposing reinforcement while breaking of existing slab.)
TOTALSCAFFOLDING
OF SECTION – :AProviding and fixing double scaffolding system (cup lock type) on the exterior side/ H FRAME, up to the height of the building
made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S.
SECTION B: CIVIL REPAIRS & Waterproofing
clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as
Sr No Description
approved and removing it thereafter .The scaffolding system shall be stiffened with bracings, runners,connection with the building etc wherever Unit
required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of
B1 SQFT
REMOVING EXISTING
Edifice Erection’s PLASTER
Consultant. TheEXTERNAL: Removing
elevational area of the existing tiles
scaffolding andbe
shall ormeasuredfor
plaster on the externalpurpose
payment walls and parapet
.The paymentwallwill
including
be made carting
once away the
debris. Cost of duration
irrespectiveof Scaffoldingis paid extra.Providing,
of scaffolding. Identification of damaged,
cutting, bending &loose,
fixingspalled plaster,
/ placing demarcating
in position the /same
Mild Steel withbars
H.Y.S.D. distinct
coatedchalk
with/ paint
'Rust colour, getting
Preventive'
B2 the
coatsame
SAND approved
ofFACE
specified
PLASTER: from
sizes the consultant
connecting
Dismantling to the and cutting
existing a groove
reinforcement
old plaster as directed mechanically
including
by up to the
welding
PMC, including depth of
/ threading
disposal of debris,
the plaster
/ tying andG.I.
with
cleaning carefully
ofbinding
exposed chipping
wire ofProviding
plasterwith
[if required]
surface, from
andthe
applying SQFT
masonry
existingcoat
double & waterproof
concrete surfaces
reinforcement complete
sand face atasany
per height
the
plaster in patches
drawing
(sponge oravg.
longthickness
& specification
finish) of stretches, ofincluding
including labour,
necessary
25mm achieved tools,
labour, tackles,
tools,
in 2coats,with materials,
tackles, stacking
materials,
base coat thecomplete
etc.
(avg. thk15mm) debris inaspremises
per the
& finishing coat
B3 carting
(avg. thkaway
specification the
&
10mm) debris
asincluding
directed fromby time
C.E tooftime
addition etc.
plasticizers, waterproofing compound in each coat (as per manufacturer’s specifications), Polypropylene/glass SQFT
fibers, curing etccomplete as instructed and directed by Edifice Erection’s Consultant (rate should includePremixed pakster, drip mould, Pattas,
platforms,
POLYMERstages etc.)
BASE CHEMICAL : Providing and applying bonding coat/ hacked plast of approved brands of polymer (WP) based chemicals between old
B9 SQFT
and new plaster
GROOVE FILLING- Surface preparation by Racking the joints at the junction of column-beam and brick work , filling it with POLYSEAL etc 1.Apply 1st
coat of POLYSEAL 0724 in a band width of 100mm to fill all external crakes.
B10 SQFT
2. 2nd coat of POLYSEAL 0724 wet coat, fix a woven net fleece of 75mm to 80mm width on the wet coat.
3. Apply 3rd coat of POLYSEAL 0724 and allow it to dry.
DASH COAT PLASTER : Providing dash coat plaster in cement mortar 1:4 to a thickness of 15 mm on badly damaged wall surfaces including inserting
Brick pieces into the wall surface and make the wall ready for final plaster. Providing & Applying dash coat plaster in one coat over extensively damaged
B12 walls with cement sand mortar 1:4, impregnating brick bat / metal pieces in the plaster & bringing the damaged surface in line & level with original wall SQFT
as per instruction including necessary labour, tools, tackles, materials, curing, carting away the debris from time to time etc. complete as
per the specification & as directed by C.E.
TOTAL OF SECTION – B
SECTION C : PLUMBING & PAINTING WORKS
Sr No Description Unit
CRACKS FILINIG:- Thermal stress crack repair on Plaster surface by open up all the visible cracks in the plaster, in a 'V' groove fashion using an electric cutter machine up to 6 to 8 mm deep & filing
C1 RFT
EPOXY PAINTING: Painting the structural steel sections on the walls with one coat of primer and two coats of epoxy paint after cleaning the rusted surfaces with
C3 sand paper. SQFT
C4 PLUMBING WORK: Proving plumbing services as directed by consultant material cost will be extra at actual. RFT
C5 PLUMBING MATERIAL- fitting including all socket,ebow and joints etc completed. Nos
C7 Chemical coating on the terrace slab:- Cleaning the existing slab with jet wash. Carefully opening the cracks in V shape and filling the same with SQFT
chemical
TOTAL OF and finishing– with
SECTION C fiber mash and proveding one coat of primer and two coat of WP chemical with specail membrane sheet.MOP suggested by
Structural
SUMMARY consultant .
A SECTION A: STRUCTURAL REPAIRS
B SECTION B: CIVIL REPAIRS & Waterproofing
C SECTION C : PLUMBING & PAINTING WORKS
CORAL REPAIR ELASTOMERIC COASTING (A+B+C)
Quantity Rate Amount
750 #REF! #REF!
200 #REF! #REF!
65 #REF! #REF!
125 #REF! #REF!
#REF!
Quantity
2000 28 56000
980 #REF! #REF!
980 #REF! #REF!
1500 20 30000
1200 #REF! #REF!
1000 #REF! #REF!
#REF!
Quantity
1500 #REF! #REF!
650 25 16250
200 0
25 0
3100 120 372000
#REF!
#REF!
#REF!
#REF!
#REF!
